powerpc/t2080rdb: Add T2080RDB board support

T2080PCIe-RDB is a Freescale Reference Design Board that hosts T2080 SoC.
The board feature overview:
Processor:
 - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
 - Single memory controller capable of supporting DDR3 and DDR3-LP devices
 - 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
 - Two 1Gbps RGMII ports on-board
 - Two 10Gbps SFP+ ports on-board
 - Two 10Gbps Base-T ports on-board
Accelerator:
 - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
IFC/Local Bus
 - NOR:  128MB 16-bit NOR flash
 - NAND: 1GB 8-bit NAND flash
 - CPLD: for system controlling with programable header on-board
eSPI:
 - 64MB N25Q512 SPI flash
USB:
 - Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
 - One PCIe x4 goldfinger(support SR-IOV)
 - One PCIe x4 slot
 - One PCIe x2 end-point device (C293 crypto co-processor)
SATA:
 - Two SATA 2.0 ports on-board
SDHC:
 - support a MicroSD/TF card on-board
I2C:
 - Four I2C controllers.
UART:
 - Dual 4-pins UART serial ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

arch/powerpc/boot/dts/t2080rdb.dts

@@ -0,0 +1,57 @@
+/*
+ * T2080PCIe-RDB Board Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t208xsi-pre.dtsi"
+/include/ "t208xrdb.dtsi"
+
+/ {
+	model = "fsl,T2080RDB";
+	compatible = "fsl,T2080RDB";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	rio: rapidio@ffe0c0000 {
+		reg = <0xf 0xfe0c0000 0 0x11000>;
+
+		port1 {
+			ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+		};
+		port2 {
+			ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+		};
+	};
+};
+
+/include/ "fsl/t2080si-post.dtsi"

arch/powerpc/boot/dts/t208xrdb.dtsi

@@ -0,0 +1,184 @@
+/*
+ * T2080PCIe-RDB Board Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/ {
+	model = "fsl,T2080RDB";
+	compatible = "fsl,T2080RDB";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	ifc: localbus@ffe124000 {
+		reg = <0xf 0xfe124000 0 0x2000>;
+		ranges = <0 0 0xf 0xe8000000 0x08000000
+			  2 0 0xf 0xff800000 0x00010000
+			  3 0 0xf 0xffdf0000 0x00008000>;
+
+		nor@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x8000000>;
+
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		nand@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x2 0x0 0x10000>;
+		};
+
+		boardctrl: board-control@2,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,t2080-cpld";
+			reg = <3 0 0x300>;
+			ranges = <0 3 0 0x300>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	dcsr: dcsr@f00000000 {
+		ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+	};
+
+	soc: soc@ffe000000 {
+		ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+		reg = <0xf 0xfe000000 0 0x00001000>;
+		spi@110000 {
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "micron,n25q512a";
+				reg = <0>;
+				spi-max-frequency = <10000000>; /* input clock */
+			};
+		};
+
+		i2c@118000 {
+			adt7481@4c {
+				compatible = "adi,adt7481";
+				reg = <0x4c>;
+			};
+
+			rtc@68 {
+				compatible = "dallas,ds1339";
+				reg = <0x68>;
+				interrupts = <0x1 0x1 0 0>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c256";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@118100 {
+			pca9546@77 {
+				compatible = "nxp,pca9546";
+				reg = <0x77>;
+			};
+		};
+
+		sdhc@114000 {
+			voltage-ranges = <1800 1800 3300 3300>;
+		};
+	};
+
+	pci0: pcie@ffe240000 {
+		reg = <0xf 0xfe240000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+			  0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x20000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci1: pcie@ffe250000 {
+		reg = <0xf 0xfe250000 0 0x10000>;
+		ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x10000000
+			  0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x20000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci2: pcie@ffe260000 {
+		reg = <0xf 0xfe260000 0 0x1000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x30000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x20000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci3: pcie@ffe270000 {
+		reg = <0xf 0xfe270000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x20000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+};

arch/powerpc/platforms/85xx/Kconfig

@@ -274,7 +274,7 @@ config CORENET_GENERIC
 	  For 32bit kernel, the following boards are supported:
 	    P2041 RDB, P3041 DS, P4080 DS, kmcoge4, and OCA4080
 	  For 64bit kernel, the following boards are supported:
-	    T208x QDS, T4240 QDS/RDB and B4 QDS
+	    T208x QDS/RDB, T4240 QDS/RDB and B4 QDS
 	  The following boards are supported for both 32bit and 64bit kernel:
 	    P5020 DS, P5040 DS and T104xQDS
 

arch/powerpc/platforms/85xx/corenet_generic.c

@@ -120,6 +120,7 @@ static const char * const boards[] __initconst = {
 	"fsl,P5020DS",
 	"fsl,P5040DS",
 	"fsl,T2080QDS",
+	"fsl,T2080RDB",
 	"fsl,T2081QDS",
 	"fsl,T4240QDS",
 	"fsl,T4240RDB",