Merge tag 'mvebu-dt-3.16-2' of git://git.infradead.org/linux-mvebu into next/dt

Merge "mvebu DT changes for v3.16 (incremental #2)" from Jason Cooper:

 - kirkwood
    - add OpenRD boards
    - make keymile boards bootable with latest kernels

 - mvebu
    - add ehci/xhci to Armada 375/38x boards

* tag 'mvebu-dt-3.16-2' of git://git.infradead.org/linux-mvebu:
  ARM: dts: kirkwood: add kirkwood-km_fixedeth DTS file
  ARM: dts: kirkwood: add kirkwood-km_common DTSI files
  ARM: dts: kirkwood: resynch 98dx4122 dtsi
  ARM: mvebu: add Device Tree description for the EHCI controllers on Armada 375
  ARM: mvebu: add Device Tree description of the xHCI controller on Armada 375
  ARM: mvebu: add Device Tree description of the EHCI controller on Armada 38x
  ARM: mvebu: add Device Tree description of xHCI controllers on Armada 38x
  ARM: Kirkwood: DT versions of OpenRD boards

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/boot/dts/Makefile

@@ -128,6 +128,9 @@ kirkwood := \
 	kirkwood-nsa310a.dtb \
 	kirkwood-openblocks_a6.dtb \
 	kirkwood-openblocks_a7.dtb \
+	kirkwood-openrd-base.dtb \
+	kirkwood-openrd-client.dtb \
+	kirkwood-openrd-ultimate.dtb \
 	kirkwood-rd88f6192.dtb \
 	kirkwood-rd88f6281-a0.dtb \
 	kirkwood-rd88f6281-a1.dtb \

arch/arm/boot/dts/armada-375-db.dts

@@ -101,6 +101,14 @@
 				};
 			};
 
+			usb@54000 {
+				status = "okay";
+			};
+
+			usb3@58000 {
+				status = "okay";
+			};
+
 			mvsdio@d4000 {
 				pinctrl-0 = <&sdio_pins &sdio_st_pins>;
 				pinctrl-names = "default";

arch/arm/boot/dts/armada-375.dtsi

@@ -345,6 +345,30 @@
 				reg = <0x21010 0x1c>;
 			};
 
+			usb@50000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x50000 0x500>;
+				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 18>;
+				status = "disabled";
+			};
+
+			usb@54000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x54000 0x500>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 26>;
+				status = "disabled";
+			};
+
+			usb3@58000 {
+				compatible = "marvell,armada-375-xhci";
+				reg = <0x58000 0x20000>,<0x5b880 0x80>;
+				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 16>;
+				status = "disabled";
+			};
+
 			xor@60800 {
 				compatible = "marvell,orion-xor";
 				reg = <0x60800 0x100

arch/arm/boot/dts/armada-385-db.dts

@@ -64,6 +64,10 @@
 				phy-mode = "rgmii-id";
 			};
 
+			usb@50000 {
+				status = "ok";
+			};
+
 			ethernet@70000 {
 				status = "okay";
 				phy = <&phy0>;
@@ -116,6 +120,14 @@
 				bus-width = <8>;
 				status = "okay";
 			};
+
+			usb3@f0000 {
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				status = "okay";
+			};
 		};
 
 		pcie-controller {

arch/arm/boot/dts/armada-385-rd.dts

@@ -76,6 +76,10 @@
 					reg = <1>;
 				};
 			};
+
+			usb3@f0000 {
+				status = "okay";
+			};
 		};
 
 		pcie-controller {

arch/arm/boot/dts/armada-38x.dtsi

@@ -312,6 +312,14 @@
 				status = "disabled";
 			};
 
+			usb@50000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x58000 0x500>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 18>;
+				status = "disabled";
+			};
+
 			xor@60800 {
 				compatible = "marvell,orion-xor";
 				reg = <0x60800 0x100
@@ -416,6 +424,22 @@
 				mrvl,clk-delay-cycles = <0x1F>;
 				status = "disabled";
 			};
+
+			usb3@f0000 {
+				compatible = "marvell,armada-380-xhci";
+				reg = <0xf0000 0x4000>,<0xf4000 0x4000>;
+				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 9>;
+				status = "disabled";
+			};
+
+			usb3@f8000 {
+				compatible = "marvell,armada-380-xhci";
+				reg = <0xf8000 0x4000>,<0xfc000 0x4000>;
+				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 10>;
+				status = "disabled";
+			};
 		};
 	};
 

arch/arm/boot/dts/kirkwood-98dx4122.dtsi

@@ -1,4 +1,39 @@
 / {
+	mbus {
+		pciec: pcie-controller {
+			compatible = "marvell,kirkwood-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0       1 0 /* Port 0.0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0       1 0 /* Port 0.0 IO  */>;
+
+			pcie0: pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &intc 9>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gate_clk 2>;
+				status = "disabled";
+			};
+		};
+	};
+
 	ocp@f1000000 {
 		pinctrl: pin-controller@10000 {
 			compatible = "marvell,98dx4122-pinctrl";
@@ -6,3 +41,11 @@
 		};
 	};
 };
+
+&sata_phy0 {
+	status = "disabled";
+};
+
+&sata_phy1 {
+	status = "disabled";
+};

arch/arm/boot/dts/kirkwood-km_common.dtsi

@@ -0,0 +1,48 @@
+/ {
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	mbus {
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-0 = < &pmx_i2c_gpio_sda &pmx_i2c_gpio_scl >;
+			pinctrl-names = "default";
+
+			pmx_i2c_gpio_sda: pmx-gpio-sda {
+				marvell,pins = "mpp8";
+				marvell,function = "gpio";
+			};
+			pmx_i2c_gpio_scl: pmx-gpio-scl {
+				marvell,pins = "mpp9";
+				marvell,function = "gpio";
+			};
+		};
+
+		serial@12000 {
+			status = "okay";
+		};
+	};
+
+	i2c@0 {
+		compatible = "i2c-gpio";
+		gpios = < &gpio0 8 GPIO_ACTIVE_HIGH		/* sda */
+			  &gpio0 9 GPIO_ACTIVE_HIGH>;		/* scl */
+		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
+	};
+};
+
+&nand {
+	status = "okay";
+	chip-delay = <25>;
+};

arch/arm/boot/dts/kirkwood-km_fixedeth.dts

@@ -0,0 +1,23 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-98dx4122.dtsi"
+#include "kirkwood-km_common.dtsi"
+
+/ {
+	model = "Keymile Kirkwood Fixed Eth";
+	compatible = "keymile,km_fixedeth", "marvell,kirkwood-98DX4122", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		speed = <1000>;  /* <SPEED_1000> */
+		duplex = <1>; /* <DUPLEX_FULL> */
+	};
+};

arch/arm/boot/dts/kirkwood-km_kirkwood.dts

@@ -2,6 +2,7 @@
 
 #include "kirkwood.dtsi"
 #include "kirkwood-98dx4122.dtsi"
+#include "kirkwood-km_common.dtsi"
 
 / {
 	model = "Keymile Kirkwood Reference Design";
@@ -11,43 +12,6 @@
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>;
 	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8 earlyprintk";
-		stdout-path = &uart0;
-	};
-
-	ocp@f1000000 {
-		pinctrl: pin-controller@10000 {
-			pinctrl-0 = < &pmx_i2c_gpio_sda &pmx_i2c_gpio_scl >;
-			pinctrl-names = "default";
-
-			pmx_i2c_gpio_sda: pmx-gpio-sda {
-				marvell,pins = "mpp8";
-				marvell,function = "gpio";
-			};
-			pmx_i2c_gpio_scl: pmx-gpio-scl {
-				marvell,pins = "mpp9";
-				marvell,function = "gpio";
-			};
-		};
-
-		serial@12000 {
-			status = "ok";
-		};
-	};
-
-	i2c@0 {
-		compatible = "i2c-gpio";
-		gpios = < &gpio0 8 GPIO_ACTIVE_HIGH		/* sda */
-			  &gpio0 9 GPIO_ACTIVE_HIGH>;		/* scl */
-		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
-	};
-};
-
-&nand {
-	status = "okay";
-	chip-delay = <25>;
 };
 
 &mdio {

arch/arm/boot/dts/kirkwood-openrd-base.dts

@@ -0,0 +1,42 @@
+/*
+ * Marvell OpenRD Base Board Description
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ * This file contains the definitions that are specific to OpenRD
+ * base variant of the Marvell Kirkwood Development Board.
+ */
+
+/dts-v1/;
+
+#include "kirkwood-openrd.dtsi"
+
+/ {
+	model = "OpenRD Base";
+	compatible = "marvell,openrd-base", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	ocp@f1000000 {
+		serial@12100 {
+			status = "okay";
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};

arch/arm/boot/dts/kirkwood-openrd-client.dts

@@ -0,0 +1,73 @@
+/*
+ * Marvell OpenRD Client Board Description
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ * This file contains the definitions that are specific to OpenRD
+ * client variant of the Marvell Kirkwood Development Board.
+ */
+
+/dts-v1/;
+
+#include "kirkwood-openrd.dtsi"
+
+/ {
+	model = "OpenRD Client";
+	compatible = "marvell,openrd-client", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	ocp@f1000000 {
+		i2c@11000 {
+			status = "okay";
+			clock-frequency = <400000>;
+
+			cs42l51: cs42l51@4a {
+				compatible = "cirrus,cs42l51";
+				reg = <0x4a>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&audio0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&cs42l51>;
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		reg = <8>;
+	};
+	ethphy1: ethernet-phy@24 {
+		reg = <24>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
+

arch/arm/boot/dts/kirkwood-openrd-ultimate.dts

@@ -0,0 +1,58 @@
+/*
+ * Marvell OpenRD Ultimate Board Description
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ * This file contains the definitions that are specific to OpenRD
+ * ultimate variant of the Marvell Kirkwood Development Board.
+ */
+
+/dts-v1/;
+
+#include "kirkwood-openrd.dtsi"
+
+/ {
+	model = "OpenRD Ultimate";
+	compatible = "marvell,openrd-ultimate", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	ocp@f1000000 {
+		i2c@11000 {
+			status = "okay";
+			clock-frequency = <400000>;
+
+			cs42l51: cs42l51@4a {
+				compatible = "cirrus,cs42l51";
+				reg = <0x4a>;
+			};
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+	ethphy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};

arch/arm/boot/dts/kirkwood-openrd.dtsi

@@ -0,0 +1,90 @@
+/*
+ * Marvell OpenRD (Base|Client|Ultimate) Board Description
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ * This file contains the definitions that are common between the three
+ * variants of the Marvell Kirkwood Development Board.
+ */
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	mbus {
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-0 = <&pmx_select28 &pmx_sdio_cd &pmx_select34>;
+			pinctrl-names = "default";
+
+			pmx_select28: pmx-select-uart-sd {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+			pmx_sdio_cd: pmx-sdio-cd {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+			pmx_select34: pmx-select-rs232-rs484 {
+				marvell,pins = "mpp34";
+				marvell,function = "gpio";
+			};
+		};
+		serial@12000 {
+			status = "okay";
+
+		};
+		sata@80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+		mvsdio@90000 {
+			status = "okay";
+			cd-gpios = <&gpio0 29 9>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+	pinctrl-0 = <&pmx_nand>;
+	pinctrl-names = "default";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+	};
+
+	partition@100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition@600000 {
+		label = "root";
+		reg = <0x0600000 0x1FA00000>;
+	};
+};