Merge branch 'i2c-mux/for-next' of https://github.com/peda-r/i2c-mux into i2c/for-4.12

Pull in changes from the i2c-mux subsubsystem:

"Here are a new LTC4306/5 driver, a fix needed by the RT kernel and some
error message cleanup."

Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt

@@ -0,0 +1,61 @@
+* Linear Technology / Analog Devices I2C bus switch
+
+Required Properties:
+
+  - compatible: Must contain one of the following.
+    "lltc,ltc4305", "lltc,ltc4306"
+  - reg: The I2C address of the device.
+
+  The following required properties are defined externally:
+
+  - Standard I2C mux properties. See i2c-mux.txt in this directory.
+  - I2C child bus nodes. See i2c-mux.txt in this directory.
+
+Optional Properties:
+
+  - enable-gpios: Reference to the GPIO connected to the enable input.
+  - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
+    children in idle state. This is necessary for example, if there are several
+    multiplexers on the bus and the devices behind them use same I2C addresses.
+  - gpio-controller: Marks the device node as a GPIO Controller.
+  - #gpio-cells: Should be two.  The first cell is the pin number and
+	the second cell is used to specify flags.
+	See ../gpio/gpio.txt for more information.
+  - ltc,downstream-accelerators-enable: Enables the rise time accelerators
+	on the downstream port.
+  - ltc,upstream-accelerators-enable: Enables the rise time accelerators
+	on the upstream port.
+
+Example:
+
+	ltc4306: i2c-mux@4a {
+		compatible = "lltc,ltc4306";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x4a>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "at,24c02";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "at,24c02";
+				reg = <0x50>;
+			};
+		};
+	};

MAINTAINERS

@@ -7698,6 +7698,14 @@ S:	Maintained
 F:	Documentation/hwmon/ltc4261
 F:	drivers/hwmon/ltc4261.c
 
+LTC4306 I2C MULTIPLEXER DRIVER
+M:	Michael Hennerich <michael.hennerich@analog.com>
+W:	http://ez.analog.com/community/linux-device-drivers
+L:	linux-i2c@vger.kernel.org
+S:	Supported
+F:	drivers/i2c/muxes/i2c-mux-ltc4306.c
+F:	Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt
+
 LTP (Linux Test Project)
 M:	Mike Frysinger <vapier@gentoo.org>
 M:	Cyril Hrubis <chrubis@suse.cz>

drivers/i2c/i2c-mux.c

@@ -395,13 +395,16 @@ int i2c_mux_add_adapter(struct i2c_mux_core *muxc,
 	if (force_nr) {
 		priv->adap.nr = force_nr;
 		ret = i2c_add_numbered_adapter(&priv->adap);
+		dev_err(&parent->dev,
+			"failed to add mux-adapter %u as bus %u (error=%d)\n",
+			chan_id, force_nr, ret);
 	} else {
 		ret = i2c_add_adapter(&priv->adap);
+		dev_err(&parent->dev,
+			"failed to add mux-adapter %u (error=%d)\n",
+			chan_id, ret);
 	}
 	if (ret < 0) {
-		dev_err(&parent->dev,
-			"failed to add mux-adapter (error=%d)\n",
-			ret);
 		kfree(priv);
 		return ret;
 	}

drivers/i2c/muxes/Kconfig

@@ -30,6 +30,17 @@ config I2C_MUX_GPIO
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-mux-gpio.
 
+config I2C_MUX_LTC4306
+	tristate "LTC LTC4306/5 I2C multiplexer"
+	select GPIOLIB
+	select REGMAP_I2C
+	help
+	  If you say yes here you get support for the Analog Devices
+	  LTC4306 or LTC4305 I2C mux/switch devices.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-mux-ltc4306.
+
 config I2C_MUX_PCA9541
 	tristate "NXP PCA9541 I2C Master Selector"
 	help

drivers/i2c/muxes/Makefile

@@ -6,6 +6,7 @@ obj-$(CONFIG_I2C_ARB_GPIO_CHALLENGE)	+= i2c-arb-gpio-challenge.o
 obj-$(CONFIG_I2C_DEMUX_PINCTRL)		+= i2c-demux-pinctrl.o
 
 obj-$(CONFIG_I2C_MUX_GPIO)	+= i2c-mux-gpio.o
+obj-$(CONFIG_I2C_MUX_LTC4306)	+= i2c-mux-ltc4306.o
 obj-$(CONFIG_I2C_MUX_MLXCPLD)	+= i2c-mux-mlxcpld.o
 obj-$(CONFIG_I2C_MUX_PCA9541)	+= i2c-mux-pca9541.o
 obj-$(CONFIG_I2C_MUX_PCA954x)	+= i2c-mux-pca954x.o

drivers/i2c/muxes/i2c-arb-gpio-challenge.c

@@ -202,10 +202,8 @@ static int i2c_arbitrator_probe(struct platform_device *pdev)
 
 	/* Actually add the mux adapter */
 	ret = i2c_mux_add_adapter(muxc, 0, 0, 0);
-	if (ret) {
-		dev_err(dev, "Failed to add adapter\n");
+	if (ret)
 		i2c_put_adapter(muxc->parent);
-	}
 
 	return ret;
 }

drivers/i2c/muxes/i2c-mux-gpio.c

@@ -245,10 +245,8 @@ static int i2c_mux_gpio_probe(struct platform_device *pdev)
 		unsigned int class = mux->data.classes ? mux->data.classes[i] : 0;
 
 		ret = i2c_mux_add_adapter(muxc, nr, mux->data.values[i], class);
-		if (ret) {
-			dev_err(&pdev->dev, "Failed to add adapter %d\n", i);
+		if (ret)
 			goto add_adapter_failed;
-		}
 	}
 
 	dev_info(&pdev->dev, "%d port mux on %s adapter\n",

drivers/i2c/muxes/i2c-mux-ltc4306.c

@@ -0,0 +1,322 @@
+/*
+ * Linear Technology LTC4306 and LTC4305 I2C multiplexer/switch
+ *
+ * Copyright (C) 2017 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2.
+ *
+ * Based on: i2c-mux-pca954x.c
+ *
+ * Datasheet: http://cds.linear.com/docs/en/datasheet/4306.pdf
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/driver.h>
+#include <linux/i2c-mux.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define LTC4305_MAX_NCHANS 2
+#define LTC4306_MAX_NCHANS 4
+
+#define LTC_REG_STATUS	0x0
+#define LTC_REG_CONFIG	0x1
+#define LTC_REG_MODE	0x2
+#define LTC_REG_SWITCH	0x3
+
+#define LTC_DOWNSTREAM_ACCL_EN	BIT(6)
+#define LTC_UPSTREAM_ACCL_EN	BIT(7)
+
+#define LTC_GPIO_ALL_INPUT	0xC0
+#define LTC_SWITCH_MASK		0xF0
+
+enum ltc_type {
+	ltc_4305,
+	ltc_4306,
+};
+
+struct chip_desc {
+	u8 nchans;
+	u8 num_gpios;
+};
+
+struct ltc4306 {
+	struct regmap *regmap;
+	struct gpio_chip gpiochip;
+	const struct chip_desc *chip;
+};
+
+static const struct chip_desc chips[] = {
+	[ltc_4305] = {
+		.nchans = LTC4305_MAX_NCHANS,
+	},
+	[ltc_4306] = {
+		.nchans = LTC4306_MAX_NCHANS,
+		.num_gpios = 2,
+	},
+};
+
+static bool ltc4306_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	return (reg == LTC_REG_CONFIG) ? true : false;
+}
+
+static const struct regmap_config ltc4306_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = LTC_REG_SWITCH,
+	.volatile_reg = ltc4306_is_volatile_reg,
+	.cache_type = REGCACHE_FLAT,
+};
+
+static int ltc4306_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct ltc4306 *data = gpiochip_get_data(chip);
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(data->regmap, LTC_REG_CONFIG, &val);
+	if (ret < 0)
+		return ret;
+
+	return !!(val & BIT(1 - offset));
+}
+
+static void ltc4306_gpio_set(struct gpio_chip *chip, unsigned int offset,
+			     int value)
+{
+	struct ltc4306 *data = gpiochip_get_data(chip);
+
+	regmap_update_bits(data->regmap, LTC_REG_CONFIG, BIT(5 - offset),
+			   value ? BIT(5 - offset) : 0);
+}
+
+static int ltc4306_gpio_get_direction(struct gpio_chip *chip,
+				      unsigned int offset)
+{
+	struct ltc4306 *data = gpiochip_get_data(chip);
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(data->regmap, LTC_REG_MODE, &val);
+	if (ret < 0)
+		return ret;
+
+	return !!(val & BIT(7 - offset));
+}
+
+static int ltc4306_gpio_direction_input(struct gpio_chip *chip,
+					unsigned int offset)
+{
+	struct ltc4306 *data = gpiochip_get_data(chip);
+
+	return regmap_update_bits(data->regmap, LTC_REG_MODE,
+				  BIT(7 - offset), BIT(7 - offset));
+}
+
+static int ltc4306_gpio_direction_output(struct gpio_chip *chip,
+					 unsigned int offset, int value)
+{
+	struct ltc4306 *data = gpiochip_get_data(chip);
+
+	ltc4306_gpio_set(chip, offset, value);
+	return regmap_update_bits(data->regmap, LTC_REG_MODE,
+				  BIT(7 - offset), 0);
+}
+
+static int ltc4306_gpio_set_config(struct gpio_chip *chip,
+				   unsigned int offset, unsigned long config)
+{
+	struct ltc4306 *data = gpiochip_get_data(chip);
+	unsigned int val;
+
+	switch (pinconf_to_config_param(config)) {
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		val = 0;
+		break;
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		val = BIT(4 - offset);
+		break;
+	default:
+		return -ENOTSUPP;
+	}
+
+	return regmap_update_bits(data->regmap, LTC_REG_MODE,
+				  BIT(4 - offset), val);
+}
+
+static int ltc4306_gpio_init(struct ltc4306 *data)
+{
+	struct device *dev = regmap_get_device(data->regmap);
+
+	if (!data->chip->num_gpios)
+		return 0;
+
+	data->gpiochip.label = dev_name(dev);
+	data->gpiochip.base = -1;
+	data->gpiochip.ngpio = data->chip->num_gpios;
+	data->gpiochip.parent = dev;
+	data->gpiochip.can_sleep = true;
+	data->gpiochip.get_direction = ltc4306_gpio_get_direction;
+	data->gpiochip.direction_input = ltc4306_gpio_direction_input;
+	data->gpiochip.direction_output = ltc4306_gpio_direction_output;
+	data->gpiochip.get = ltc4306_gpio_get;
+	data->gpiochip.set = ltc4306_gpio_set;
+	data->gpiochip.set_config = ltc4306_gpio_set_config;
+	data->gpiochip.owner = THIS_MODULE;
+
+	/* gpiolib assumes all GPIOs default input */
+	regmap_write(data->regmap, LTC_REG_MODE, LTC_GPIO_ALL_INPUT);
+
+	return devm_gpiochip_add_data(dev, &data->gpiochip, data);
+}
+
+static int ltc4306_select_mux(struct i2c_mux_core *muxc, u32 chan)
+{
+	struct ltc4306 *data = i2c_mux_priv(muxc);
+
+	return regmap_update_bits(data->regmap, LTC_REG_SWITCH,
+				  LTC_SWITCH_MASK, BIT(7 - chan));
+}
+
+static int ltc4306_deselect_mux(struct i2c_mux_core *muxc, u32 chan)
+{
+	struct ltc4306 *data = i2c_mux_priv(muxc);
+
+	return regmap_update_bits(data->regmap, LTC_REG_SWITCH,
+				  LTC_SWITCH_MASK, 0);
+}
+
+static const struct i2c_device_id ltc4306_id[] = {
+	{ "ltc4305", ltc_4305 },
+	{ "ltc4306", ltc_4306 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, ltc4306_id);
+
+static const struct of_device_id ltc4306_of_match[] = {
+	{ .compatible = "lltc,ltc4305", .data = &chips[ltc_4305] },
+	{ .compatible = "lltc,ltc4306", .data = &chips[ltc_4306] },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ltc4306_of_match);
+
+static int ltc4306_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct i2c_adapter *adap = to_i2c_adapter(client->dev.parent);
+	const struct chip_desc *chip;
+	struct i2c_mux_core *muxc;
+	struct ltc4306 *data;
+	struct gpio_desc *gpio;
+	bool idle_disc;
+	unsigned int val = 0;
+	int num, ret;
+
+	chip = of_device_get_match_data(&client->dev);
+
+	if (!chip)
+		chip = &chips[id->driver_data];
+
+	idle_disc = device_property_read_bool(&client->dev,
+					      "i2c-mux-idle-disconnect");
+
+	muxc = i2c_mux_alloc(adap, &client->dev,
+			     chip->nchans, sizeof(*data),
+			     I2C_MUX_LOCKED, ltc4306_select_mux,
+			     idle_disc ? ltc4306_deselect_mux : NULL);
+	if (!muxc)
+		return -ENOMEM;
+	data = i2c_mux_priv(muxc);
+	data->chip = chip;
+
+	i2c_set_clientdata(client, muxc);
+
+	data->regmap = devm_regmap_init_i2c(client, &ltc4306_regmap_config);
+	if (IS_ERR(data->regmap)) {
+		ret = PTR_ERR(data->regmap);
+		dev_err(&client->dev, "Failed to allocate register map: %d\n",
+			ret);
+		return ret;
+	}
+
+	/* Reset and enable the mux if an enable GPIO is specified. */
+	gpio = devm_gpiod_get_optional(&client->dev, "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(gpio))
+		return PTR_ERR(gpio);
+
+	if (gpio) {
+		udelay(1);
+		gpiod_set_value(gpio, 1);
+	}
+
+	/*
+	 * Write the mux register at addr to verify
+	 * that the mux is in fact present. This also
+	 * initializes the mux to disconnected state.
+	 */
+	if (regmap_write(data->regmap, LTC_REG_SWITCH, 0) < 0) {
+		dev_warn(&client->dev, "probe failed\n");
+		return -ENODEV;
+	}
+
+	if (device_property_read_bool(&client->dev,
+				      "ltc,downstream-accelerators-enable"))
+		val |= LTC_DOWNSTREAM_ACCL_EN;
+
+	if (device_property_read_bool(&client->dev,
+				      "ltc,upstream-accelerators-enable"))
+		val |= LTC_UPSTREAM_ACCL_EN;
+
+	if (regmap_write(data->regmap, LTC_REG_CONFIG, val) < 0)
+		return -ENODEV;
+
+	ret = ltc4306_gpio_init(data);
+	if (ret < 0)
+		return ret;
+
+	/* Now create an adapter for each channel */
+	for (num = 0; num < chip->nchans; num++) {
+		ret = i2c_mux_add_adapter(muxc, 0, num, 0);
+		if (ret) {
+			i2c_mux_del_adapters(muxc);
+			return ret;
+		}
+	}
+
+	dev_info(&client->dev,
+		 "registered %d multiplexed busses for I2C switch %s\n",
+		 num, client->name);
+
+	return 0;
+}
+
+static int ltc4306_remove(struct i2c_client *client)
+{
+	struct i2c_mux_core *muxc = i2c_get_clientdata(client);
+
+	i2c_mux_del_adapters(muxc);
+
+	return 0;
+}
+
+static struct i2c_driver ltc4306_driver = {
+	.driver		= {
+		.name	= "ltc4306",
+		.of_match_table = of_match_ptr(ltc4306_of_match),
+	},
+	.probe		= ltc4306_probe,
+	.remove		= ltc4306_remove,
+	.id_table	= ltc4306_id,
+};
+
+module_i2c_driver(ltc4306_driver);
+
+MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>");
+MODULE_DESCRIPTION("Linear Technology LTC4306, LTC4305 I2C mux/switch driver");
+MODULE_LICENSE("GPL v2");

drivers/i2c/muxes/i2c-mux-pca9541.c

@@ -369,10 +369,8 @@ static int pca9541_probe(struct i2c_client *client,
 	i2c_set_clientdata(client, muxc);
 
 	ret = i2c_mux_add_adapter(muxc, force, 0, 0);
-	if (ret) {
-		dev_err(&client->dev, "failed to register master selector\n");
+	if (ret)
 		return ret;
-	}
 
 	dev_info(&client->dev, "registered master selector for I2C %s\n",
 		 client->name);

drivers/i2c/muxes/i2c-mux-pca954x.c

@@ -85,7 +85,7 @@ struct pca954x {
 
 	struct irq_domain *irq;
 	unsigned int irq_mask;
-	spinlock_t lock;
+	raw_spinlock_t lock;
 };
 
 /* Provide specs for the PCA954x types we know about */
@@ -264,13 +264,13 @@ static void pca954x_irq_mask(struct irq_data *idata)
 	unsigned int pos = idata->hwirq;
 	unsigned long flags;
 
-	spin_lock_irqsave(&data->lock, flags);
+	raw_spin_lock_irqsave(&data->lock, flags);
 
 	data->irq_mask &= ~BIT(pos);
 	if (!data->irq_mask)
 		disable_irq(data->client->irq);
 
-	spin_unlock_irqrestore(&data->lock, flags);
+	raw_spin_unlock_irqrestore(&data->lock, flags);
 }
 
 static void pca954x_irq_unmask(struct irq_data *idata)
@@ -279,13 +279,13 @@ static void pca954x_irq_unmask(struct irq_data *idata)
 	unsigned int pos = idata->hwirq;
 	unsigned long flags;
 
-	spin_lock_irqsave(&data->lock, flags);
+	raw_spin_lock_irqsave(&data->lock, flags);
 
 	if (!data->irq_mask)
 		enable_irq(data->client->irq);
 	data->irq_mask |= BIT(pos);
 
-	spin_unlock_irqrestore(&data->lock, flags);
+	raw_spin_unlock_irqrestore(&data->lock, flags);
 }
 
 static int pca954x_irq_set_type(struct irq_data *idata, unsigned int type)
@@ -311,7 +311,7 @@ static int pca954x_irq_setup(struct i2c_mux_core *muxc)
 	if (!data->chip->has_irq || client->irq <= 0)
 		return 0;
 
-	spin_lock_init(&data->lock);
+	raw_spin_lock_init(&data->lock);
 
 	data->irq = irq_domain_add_linear(client->dev.of_node,
 					  data->chip->nchans,
@@ -434,13 +434,8 @@ static int pca954x_probe(struct i2c_client *client,
 				   idle_disconnect_dt) << num;
 
 		ret = i2c_mux_add_adapter(muxc, force, num, class);
-
-		if (ret) {
-			dev_err(&client->dev,
-				"failed to register multiplexed adapter"
-				" %d as bus %d\n", num, force);
+		if (ret)
 			goto fail_del_adapters;
-		}
 	}
 
 	dev_info(&client->dev,

drivers/i2c/muxes/i2c-mux-pinctrl.c

@@ -245,10 +245,8 @@ static int i2c_mux_pinctrl_probe(struct platform_device *pdev)
 				(mux->pdata->base_bus_num + i) : 0;
 
 		ret = i2c_mux_add_adapter(muxc, bus, i, 0);
-		if (ret) {
-			dev_err(&pdev->dev, "Failed to add adapter %d\n", i);
+		if (ret)
 			goto err_del_adapter;
-		}
 	}
 
 	return 0;

drivers/i2c/muxes/i2c-mux-reg.c

@@ -222,10 +222,8 @@ static int i2c_mux_reg_probe(struct platform_device *pdev)
 		class = mux->data.classes ? mux->data.classes[i] : 0;
 
 		ret = i2c_mux_add_adapter(muxc, nr, mux->data.values[i], class);
-		if (ret) {
-			dev_err(&pdev->dev, "Failed to add adapter %d\n", i);
+		if (ret)
 			goto add_adapter_failed;
-		}
 	}
 
 	dev_dbg(&pdev->dev, "%d port mux on %s adapter\n",