Merge branch 'synaptics-rmi4' into next

Bring in support for devices using Synaptics RMI4 protocol, including
RMI4 bus, 2D sensor and button handlers, and SPI and I2C interface
drivers.

Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt

@@ -0,0 +1,56 @@
+Synaptics RMI4 2D Sensor Device Binding
+
+The Synaptics RMI4 core is able to support RMI4 devices using different
+transports and different functions. This file describes the device tree
+bindings for devices which contain 2D sensors using Function 11 or
+Function 12. Complete documentation for transports and other functions
+can be found in:
+Documentation/devicetree/bindings/input/rmi4.
+
+RMI4 Function 11 and Function 12 are for 2D touch position sensing.
+Additional documentation for F11 can be found at:
+http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf
+
+Optional Touch Properties:
+Description in Documentation/devicetree/bindings/input/touch
+- touchscreen-inverted-x
+- touchscreen-inverted-y
+- touchscreen-swapped-x-y
+- touchscreen-x-mm
+- touchscreen-y-mm
+
+Optional Properties:
+- syna,clip-x-low: Sets a minimum value for X.
+- syna,clip-y-low: Sets a minimum value for Y.
+- syna,clip-x-high: Sets a maximum value for X.
+- syna,clip-y-high: Sets a maximum value for Y.
+- syna,offset-x: Add an offset to X.
+- syna,offset-y: Add an offset to Y.
+- syna,delta-x-threshold: Set the minimum distance on the X axis required
+				to generate an interrupt in reduced reporting
+				mode.
+- syna,delta-y-threshold: Set the minimum distance on the Y axis required
+				to generate an interrupt in reduced reporting
+				mode.
+- syna,sensor-type: Set the sensor type. 1 for touchscreen 2 for touchpad.
+- syna,disable-report-mask: Mask for disabling posiiton reporting. Used to
+				disable reporing absolute position data.
+- syna,rezero-wait-ms: Time in miliseconds to wait after issuing a rezero
+				command.
+
+
+Example of a RMI4 I2C device with F11:
+Example:
+	&i2c1 {
+		rmi4-i2c-dev@2c {
+			compatible = "syna,rmi4-i2c";
+
+			...
+
+			rmi4-f11@11 {
+				reg = <0x11>;
+				touchscreen-inverted-y;
+				syna,sensor-type = <2>;
+			};
+		};
+	};

Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt

@@ -0,0 +1,39 @@
+Synaptics RMI4 F01 Device Binding
+
+The Synaptics RMI4 core is able to support RMI4 devices using different
+transports and different functions. This file describes the device tree
+bindings for devices which contain Function 1. Complete documentation
+for transports and other functions can be found in:
+Documentation/devicetree/bindings/input/rmi4.
+
+Additional documentation for F01 can be found at:
+http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf
+
+Optional Properties:
+- syna,nosleep-mode: If set the device will run at full power without sleeping.
+			nosleep has 3 modes, 0 will not change the default
+			setting, 1 will disable nosleep (allow sleeping),
+			and 2 will enable nosleep (disabling sleep).
+- syna,wakeup-threshold: Defines the amplitude of the disturbance to the
+				background capacitance that will cause the
+				device to wake from dozing.
+- syna,doze-holdoff-ms: The delay to wait after the last finger lift and the
+				first doze cycle.
+- syna,doze-interval-ms: The time period that the device sleeps between finger
+				activity.
+
+
+Example of a RMI4 I2C device with F01:
+	Example:
+	&i2c1 {
+		rmi4-i2c-dev@2c {
+			compatible = "syna,rmi4-i2c";
+
+			...
+
+			rmi4-f01@1 {
+				reg = <0x1>;
+				syna,nosleep-mode = <1>;
+			};
+		};
+	};

Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt

@@ -0,0 +1,53 @@
+Synaptics RMI4 I2C Device Binding
+
+The Synaptics RMI4 core is able to support RMI4 devices using different
+transports and different functions. This file describes the device tree
+bindings for devices using the I2C transport driver. Complete documentation
+for other transports and functions can be found in
+Documentation/devicetree/bindings/input/rmi4.
+
+Required Properties:
+- compatible: syna,rmi4-i2c
+- reg: I2C address
+- #address-cells: Set to 1 to indicate that the function child nodes
+		    consist of only on uint32 value.
+- #size-cells: Set to 0 to indicate that the function child nodes do not
+		have a size property.
+
+Optional Properties:
+- interrupts: interrupt which the rmi device is connected to.
+- interrupt-parent: The interrupt controller.
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+- syna,reset-delay-ms: The number of milliseconds to wait after resetting the
+			device.
+
+Function Parameters:
+Parameters specific to RMI functions are contained in child nodes of the rmi device
+ node. Documentation for the parameters of each function can be found in:
+Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt.
+
+
+
+Example:
+	&i2c1 {
+		rmi4-i2c-dev@2c {
+			compatible = "syna,rmi4-i2c";
+			reg = <0x2c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupt-parent = <&gpio>;
+			interrupts = <4 2>;
+
+			rmi4-f01@1 {
+				reg = <0x1>;
+				syna,nosleep-mode = <1>;
+			};
+
+			rmi4-f11@11 {
+				reg = <0x11>;
+				touchscreen-inverted-y;
+				syna,sensor-type = <2>;
+			};
+		};
+	};

Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt

@@ -0,0 +1,57 @@
+Synaptics RMI4 SPI Device Binding
+
+The Synaptics RMI4 core is able to support RMI4 devices using different
+transports and different functions. This file describes the device tree
+bindings for devices using the SPI transport driver. Complete documentation
+for other transports and functions can be found in
+Documentation/devicetree/bindings/input/rmi4.
+
+Required Properties:
+- compatible: syna,rmi4-spi
+- reg: Chip select address for the device
+- #address-cells: Set to 1 to indicate that the function child nodes
+		    consist of only on uint32 value.
+- #size-cells: Set to 0 to indicate that the function child nodes do not
+		have a size property.
+
+Optional Properties:
+- interrupts: interrupt which the rmi device is connected to.
+- interrupt-parent: The interrupt controller.
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+- spi-rx-delay-us: microsecond delay after a read transfer.
+- spi-tx-delay-us: microsecond delay after a write transfer.
+
+Function Parameters:
+Parameters specific to RMI functions are contained in child nodes of the rmi device
+ node. Documentation for the parameters of each function can be found in:
+Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt.
+
+
+
+Example:
+	spi@7000d800 {
+		rmi4-spi-dev@0 {
+			compatible = "syna,rmi4-spi";
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			spi-max-frequency = <4000000>;
+			spi-cpha;
+			spi-cpol;
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(K, 2) 0x2>;
+			spi-rx-delay-us = <30>;
+
+			rmi4-f01@1 {
+				reg = <0x1>;
+				syna,nosleep-mode = <1>;
+			};
+
+			rmi4-f11@11 {
+				reg = <0x11>;
+				touchscreen-inverted-y;
+				syna,sensor-type = <2>;
+			};
+		};
+	};

Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt

@@ -18,6 +18,8 @@ Optional properties for Touchscreens:
  - touchscreen-inverted-y	: Y axis is inverted (boolean)
  - touchscreen-swapped-x-y	: X and Y axis are swapped (boolean)
 				  Swapping is done after inverting the axis
+ - touchscreen-x-mm		: horizontal length in mm of the touchscreen
+ - touchscreen-y-mm		: vertical length in mm of the touchscreen
 
 Deprecated properties for Touchscreens:
  - x-size			: deprecated name for touchscreen-size-x

Documentation/devicetree/bindings/spi/spi-bus.txt

@@ -61,6 +61,8 @@ contain the following properties.
                       used for MOSI. Defaults to 1 if not present.
 - spi-rx-bus-width - (optional) The bus width(number of data wires) that
                       used for MISO. Defaults to 1 if not present.
+- spi-rx-delay-us  - (optional) Microsecond delay after a read transfer.
+- spi-tx-delay-us  - (optional) Microsecond delay after a write transfer.
 
 Some SPI controllers and devices support Dual and Quad SPI transfer mode.
 It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD).

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -220,6 +220,7 @@ sprd	Spreadtrum Communications Inc.
 st	STMicroelectronics
 ste	ST-Ericsson
 stericsson	ST-Ericsson
+syna	Synaptics Inc.
 synology	Synology, Inc.
 tbs	TBS Technologies
 tcl	Toby Churchill Ltd.

drivers/input/Kconfig

@@ -201,6 +201,8 @@ source "drivers/input/touchscreen/Kconfig"
 
 source "drivers/input/misc/Kconfig"
 
+source "drivers/input/rmi4/Kconfig"
+
 endif
 
 menu "Hardware I/O ports"

drivers/input/Makefile

@@ -26,3 +26,5 @@ obj-$(CONFIG_INPUT_TOUCHSCREEN)	+= touchscreen/
 obj-$(CONFIG_INPUT_MISC)	+= misc/
 
 obj-$(CONFIG_INPUT_APMPOWER)	+= apm-power.o
+
+obj-$(CONFIG_RMI4_CORE)		+= rmi4/

drivers/input/rmi4/Kconfig

@@ -0,0 +1,63 @@
+#
+# RMI4 configuration
+#
+config RMI4_CORE
+	tristate "Synaptics RMI4 bus support"
+	help
+	  Say Y here if you want to support the Synaptics RMI4 bus.  This is
+	  required for all RMI4 device support.
+
+	  If unsure, say Y.
+
+config RMI4_I2C
+	tristate "RMI4 I2C Support"
+	depends on RMI4_CORE && I2C
+	help
+	  Say Y here if you want to support RMI4 devices connected to an I2C
+	  bus.
+
+	  If unsure, say Y.
+
+config RMI4_SPI
+	tristate "RMI4 SPI Support"
+	depends on RMI4_CORE && SPI
+	help
+	  Say Y here if you want to support RMI4 devices connected to a SPI
+	  bus.
+
+	  If unsure, say N.
+
+config RMI4_2D_SENSOR
+	bool
+	depends on RMI4_CORE
+
+config RMI4_F11
+	bool "RMI4 Function 11 (2D pointing)"
+	select RMI4_2D_SENSOR
+	depends on RMI4_CORE
+	help
+	  Say Y here if you want to add support for RMI4 function 11.
+
+	  Function 11 provides 2D multifinger pointing for touchscreens and
+	  touchpads. For sensors that support relative pointing, F11 also
+	  provides mouse input.
+
+config RMI4_F12
+	bool "RMI4 Function 12 (2D pointing)"
+	select RMI4_2D_SENSOR
+	depends on RMI4_CORE
+	help
+	  Say Y here if you want to add support for RMI4 function 12.
+
+	  Function 12 provides 2D multifinger pointing for touchscreens and
+	  touchpads. For sensors that support relative pointing, F12 also
+	  provides mouse input.
+
+config RMI4_F30
+	bool "RMI4 Function 30 (GPIO LED)"
+	depends on RMI4_CORE
+	help
+	  Say Y here if you want to add support for RMI4 function 30.
+
+	  Function 30 provides GPIO and LED support for RMI4 devices. This
+	  includes support for buttons on TouchPads and ClickPads.

drivers/input/rmi4/Makefile

@@ -0,0 +1,13 @@
+obj-$(CONFIG_RMI4_CORE) += rmi_core.o
+rmi_core-y := rmi_bus.o rmi_driver.o rmi_f01.o
+
+rmi_core-$(CONFIG_RMI4_2D_SENSOR) += rmi_2d_sensor.o
+
+# Function drivers
+rmi_core-$(CONFIG_RMI4_F11) += rmi_f11.o
+rmi_core-$(CONFIG_RMI4_F12) += rmi_f12.o
+rmi_core-$(CONFIG_RMI4_F30) += rmi_f30.o
+
+# Transports
+obj-$(CONFIG_RMI4_I2C) += rmi_i2c.o
+obj-$(CONFIG_RMI4_SPI) += rmi_spi.o

drivers/input/rmi4/rmi_2d_sensor.c

@@ -0,0 +1,329 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/of.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/rmi.h>
+#include "rmi_driver.h"
+#include "rmi_2d_sensor.h"
+
+#define RMI_2D_REL_POS_MIN		-128
+#define RMI_2D_REL_POS_MAX		127
+
+/* maximum ABS_MT_POSITION displacement (in mm) */
+#define DMAX 10
+
+void rmi_2d_sensor_abs_process(struct rmi_2d_sensor *sensor,
+				struct rmi_2d_sensor_abs_object *obj,
+				int slot)
+{
+	struct rmi_2d_axis_alignment *axis_align = &sensor->axis_align;
+
+	/* we keep the previous values if the finger is released */
+	if (obj->type == RMI_2D_OBJECT_NONE)
+		return;
+
+	if (axis_align->swap_axes)
+		swap(obj->x, obj->y);
+
+	if (axis_align->flip_x)
+		obj->x = sensor->max_x - obj->x;
+
+	if (axis_align->flip_y)
+		obj->y = sensor->max_y - obj->y;
+
+	/*
+	 * Here checking if X offset or y offset are specified is
+	 * redundant. We just add the offsets or clip the values.
+	 *
+	 * Note: offsets need to be applied before clipping occurs,
+	 * or we could get funny values that are outside of
+	 * clipping boundaries.
+	 */
+	obj->x += axis_align->offset_x;
+	obj->y += axis_align->offset_y;
+
+	obj->x =  max(axis_align->clip_x_low, obj->x);
+	obj->y =  max(axis_align->clip_y_low, obj->y);
+
+	if (axis_align->clip_x_high)
+		obj->x = min(sensor->max_x, obj->x);
+
+	if (axis_align->clip_y_high)
+		obj->y =  min(sensor->max_y, obj->y);
+
+	sensor->tracking_pos[slot].x = obj->x;
+	sensor->tracking_pos[slot].y = obj->y;
+}
+EXPORT_SYMBOL_GPL(rmi_2d_sensor_abs_process);
+
+void rmi_2d_sensor_abs_report(struct rmi_2d_sensor *sensor,
+				struct rmi_2d_sensor_abs_object *obj,
+				int slot)
+{
+	struct rmi_2d_axis_alignment *axis_align = &sensor->axis_align;
+	struct input_dev *input = sensor->input;
+	int wide, major, minor;
+
+	if (sensor->kernel_tracking)
+		input_mt_slot(input, sensor->tracking_slots[slot]);
+	else
+		input_mt_slot(input, slot);
+
+	input_mt_report_slot_state(input, obj->mt_tool,
+				   obj->type != RMI_2D_OBJECT_NONE);
+
+	if (obj->type != RMI_2D_OBJECT_NONE) {
+		obj->x = sensor->tracking_pos[slot].x;
+		obj->y = sensor->tracking_pos[slot].y;
+
+		if (axis_align->swap_axes)
+			swap(obj->wx, obj->wy);
+
+		wide = (obj->wx > obj->wy);
+		major = max(obj->wx, obj->wy);
+		minor = min(obj->wx, obj->wy);
+
+		if (obj->type == RMI_2D_OBJECT_STYLUS) {
+			major = max(1, major);
+			minor = max(1, minor);
+		}
+
+		input_event(sensor->input, EV_ABS, ABS_MT_POSITION_X, obj->x);
+		input_event(sensor->input, EV_ABS, ABS_MT_POSITION_Y, obj->y);
+		input_event(sensor->input, EV_ABS, ABS_MT_ORIENTATION, wide);
+		input_event(sensor->input, EV_ABS, ABS_MT_PRESSURE, obj->z);
+		input_event(sensor->input, EV_ABS, ABS_MT_TOUCH_MAJOR, major);
+		input_event(sensor->input, EV_ABS, ABS_MT_TOUCH_MINOR, minor);
+
+		rmi_dbg(RMI_DEBUG_2D_SENSOR, &sensor->input->dev,
+			"%s: obj[%d]: type: 0x%02x X: %d Y: %d Z: %d WX: %d WY: %d\n",
+			__func__, slot, obj->type, obj->x, obj->y, obj->z,
+			obj->wx, obj->wy);
+	}
+}
+EXPORT_SYMBOL_GPL(rmi_2d_sensor_abs_report);
+
+void rmi_2d_sensor_rel_report(struct rmi_2d_sensor *sensor, int x, int y)
+{
+	struct rmi_2d_axis_alignment *axis_align = &sensor->axis_align;
+
+	x = min(RMI_2D_REL_POS_MAX, max(RMI_2D_REL_POS_MIN, (int)x));
+	y = min(RMI_2D_REL_POS_MAX, max(RMI_2D_REL_POS_MIN, (int)y));
+
+	if (axis_align->swap_axes)
+		swap(x, y);
+
+	if (axis_align->flip_x)
+		x = min(RMI_2D_REL_POS_MAX, -x);
+
+	if (axis_align->flip_y)
+		y = min(RMI_2D_REL_POS_MAX, -y);
+
+	if (x || y) {
+		input_report_rel(sensor->input, REL_X, x);
+		input_report_rel(sensor->input, REL_Y, y);
+	}
+}
+EXPORT_SYMBOL_GPL(rmi_2d_sensor_rel_report);
+
+static void rmi_2d_sensor_set_input_params(struct rmi_2d_sensor *sensor)
+{
+	struct input_dev *input = sensor->input;
+	int res_x;
+	int res_y;
+	int input_flags = 0;
+
+	if (sensor->report_abs) {
+		if (sensor->axis_align.swap_axes)
+			swap(sensor->max_x, sensor->max_y);
+
+		sensor->min_x = sensor->axis_align.clip_x_low;
+		if (sensor->axis_align.clip_x_high)
+			sensor->max_x = min(sensor->max_x,
+				sensor->axis_align.clip_x_high);
+
+		sensor->min_y = sensor->axis_align.clip_y_low;
+		if (sensor->axis_align.clip_y_high)
+			sensor->max_y = min(sensor->max_y,
+				sensor->axis_align.clip_y_high);
+
+		set_bit(EV_ABS, input->evbit);
+		input_set_abs_params(input, ABS_MT_POSITION_X, 0, sensor->max_x,
+					0, 0);
+		input_set_abs_params(input, ABS_MT_POSITION_Y, 0, sensor->max_y,
+					0, 0);
+
+		if (sensor->x_mm && sensor->y_mm) {
+			res_x = (sensor->max_x - sensor->min_x) / sensor->x_mm;
+			res_y = (sensor->max_y - sensor->min_y) / sensor->y_mm;
+
+			input_abs_set_res(input, ABS_X, res_x);
+			input_abs_set_res(input, ABS_Y, res_y);
+
+			input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
+			input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+
+			if (!sensor->dmax)
+				sensor->dmax = DMAX * res_x;
+		}
+
+		input_set_abs_params(input, ABS_MT_PRESSURE, 0,	0xff, 0, 0);
+		input_set_abs_params(input, ABS_MT_TOUCH_MAJOR,	0, 0x0f, 0, 0);
+		input_set_abs_params(input, ABS_MT_TOUCH_MINOR,	0, 0x0f, 0, 0);
+		input_set_abs_params(input, ABS_MT_ORIENTATION,	0, 1, 0, 0);
+
+		if (sensor->sensor_type == rmi_sensor_touchpad)
+			input_flags = INPUT_MT_POINTER;
+		else
+			input_flags = INPUT_MT_DIRECT;
+
+		if (sensor->kernel_tracking)
+			input_flags |= INPUT_MT_TRACK;
+
+		input_mt_init_slots(input, sensor->nbr_fingers, input_flags);
+	}
+
+	if (sensor->report_rel) {
+		set_bit(EV_REL, input->evbit);
+		set_bit(REL_X, input->relbit);
+		set_bit(REL_Y, input->relbit);
+	}
+
+	if (sensor->topbuttonpad)
+		set_bit(INPUT_PROP_TOPBUTTONPAD, input->propbit);
+}
+EXPORT_SYMBOL_GPL(rmi_2d_sensor_set_input_params);
+
+int rmi_2d_sensor_configure_input(struct rmi_function *fn,
+					struct rmi_2d_sensor *sensor)
+{
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	struct rmi_driver_data *drv_data = dev_get_drvdata(&rmi_dev->dev);
+
+	if (!drv_data->input)
+		return -ENODEV;
+
+	sensor->input = drv_data->input;
+	rmi_2d_sensor_set_input_params(sensor);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(rmi_2d_sensor_configure_input);
+
+#ifdef CONFIG_OF
+int rmi_2d_sensor_of_probe(struct device *dev,
+			struct rmi_2d_sensor_platform_data *pdata)
+{
+	int retval;
+	u32 val;
+
+	pdata->axis_align.swap_axes = of_property_read_bool(dev->of_node,
+						"touchscreen-swapped-x-y");
+
+	pdata->axis_align.flip_x = of_property_read_bool(dev->of_node,
+						"touchscreen-inverted-x");
+
+	pdata->axis_align.flip_y = of_property_read_bool(dev->of_node,
+						"touchscreen-inverted-y");
+
+	retval = rmi_of_property_read_u32(dev, &val, "syna,clip-x-low", 1);
+	if (retval)
+		return retval;
+
+	pdata->axis_align.clip_x_low = val;
+
+	retval = rmi_of_property_read_u32(dev, &val, "syna,clip-y-low",	1);
+	if (retval)
+		return retval;
+
+	pdata->axis_align.clip_y_low = val;
+
+	retval = rmi_of_property_read_u32(dev, &val, "syna,clip-x-high", 1);
+	if (retval)
+		return retval;
+
+	pdata->axis_align.clip_x_high = val;
+
+	retval = rmi_of_property_read_u32(dev, &val, "syna,clip-y-high", 1);
+	if (retval)
+		return retval;
+
+	pdata->axis_align.clip_y_high = val;
+
+	retval = rmi_of_property_read_u32(dev, &val, "syna,offset-x", 1);
+	if (retval)
+		return retval;
+
+	pdata->axis_align.offset_x = val;
+
+	retval = rmi_of_property_read_u32(dev, &val, "syna,offset-y", 1);
+	if (retval)
+		return retval;
+
+	pdata->axis_align.offset_y = val;
+
+	retval = rmi_of_property_read_u32(dev, &val, "syna,delta-x-threshold",
+						1);
+	if (retval)
+		return retval;
+
+	pdata->axis_align.delta_x_threshold = val;
+
+	retval = rmi_of_property_read_u32(dev, &val, "syna,delta-y-threshold",
+						1);
+	if (retval)
+		return retval;
+
+	pdata->axis_align.delta_y_threshold = val;
+
+	retval = rmi_of_property_read_u32(dev, (u32 *)&pdata->sensor_type,
+			"syna,sensor-type", 1);
+	if (retval)
+		return retval;
+
+	retval = rmi_of_property_read_u32(dev, &val, "touchscreen-x-mm", 1);
+	if (retval)
+		return retval;
+
+	pdata->x_mm = val;
+
+	retval = rmi_of_property_read_u32(dev, &val, "touchscreen-y-mm", 1);
+	if (retval)
+		return retval;
+
+	pdata->y_mm = val;
+
+	retval = rmi_of_property_read_u32(dev, &val,
+				"syna,disable-report-mask", 1);
+	if (retval)
+		return retval;
+
+	pdata->disable_report_mask = val;
+
+	retval = rmi_of_property_read_u32(dev, &val, "syna,rezero-wait-ms",
+						1);
+	if (retval)
+		return retval;
+
+	pdata->rezero_wait = val;
+
+	return 0;
+}
+#else
+inline int rmi_2d_sensor_of_probe(struct device *dev,
+			struct rmi_2d_sensor_platform_data *pdata)
+{
+	return -ENODEV;
+}
+#endif
+EXPORT_SYMBOL_GPL(rmi_2d_sensor_of_probe);

drivers/input/rmi4/rmi_2d_sensor.h

@@ -0,0 +1,87 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#ifndef _RMI_2D_SENSOR_H
+#define _RMI_2D_SENSOR_H
+
+enum rmi_2d_sensor_object_type {
+	RMI_2D_OBJECT_NONE,
+	RMI_2D_OBJECT_FINGER,
+	RMI_2D_OBJECT_STYLUS,
+	RMI_2D_OBJECT_PALM,
+	RMI_2D_OBJECT_UNCLASSIFIED,
+};
+
+struct rmi_2d_sensor_abs_object {
+	enum rmi_2d_sensor_object_type type;
+	int mt_tool;
+	u16 x;
+	u16 y;
+	u8 z;
+	u8 wx;
+	u8 wy;
+};
+
+/**
+ * @axis_align - controls parameters that are useful in system prototyping
+ * and bring up.
+ * @max_x - The maximum X coordinate that will be reported by this sensor.
+ * @max_y - The maximum Y coordinate that will be reported by this sensor.
+ * @nbr_fingers - How many fingers can this sensor report?
+ * @data_pkt - buffer for data reported by this sensor.
+ * @pkt_size - number of bytes in that buffer.
+ * @attn_size - Size of the HID attention report (only contains abs data).
+ * position when two fingers are on the device.  When this is true, we
+ * assume we have one of those sensors and report events appropriately.
+ * @sensor_type - indicates whether we're touchscreen or touchpad.
+ * @input - input device for absolute pointing stream
+ * @input_phys - buffer for the absolute phys name for this sensor.
+ */
+struct rmi_2d_sensor {
+	struct rmi_2d_axis_alignment axis_align;
+	struct input_mt_pos *tracking_pos;
+	int *tracking_slots;
+	bool kernel_tracking;
+	struct rmi_2d_sensor_abs_object *objs;
+	int dmax;
+	u16 min_x;
+	u16 max_x;
+	u16 min_y;
+	u16 max_y;
+	u8 nbr_fingers;
+	u8 *data_pkt;
+	int pkt_size;
+	int attn_size;
+	bool topbuttonpad;
+	enum rmi_sensor_type sensor_type;
+	struct input_dev *input;
+	struct rmi_function *fn;
+	char input_phys[32];
+	u8 report_abs;
+	u8 report_rel;
+	u8 x_mm;
+	u8 y_mm;
+};
+
+int rmi_2d_sensor_of_probe(struct device *dev,
+				struct rmi_2d_sensor_platform_data *pdata);
+
+void rmi_2d_sensor_abs_process(struct rmi_2d_sensor *sensor,
+				struct rmi_2d_sensor_abs_object *obj,
+				int slot);
+
+void rmi_2d_sensor_abs_report(struct rmi_2d_sensor *sensor,
+				struct rmi_2d_sensor_abs_object *obj,
+				int slot);
+
+void rmi_2d_sensor_rel_report(struct rmi_2d_sensor *sensor, int x, int y);
+
+int rmi_2d_sensor_configure_input(struct rmi_function *fn,
+					struct rmi_2d_sensor *sensor);
+#endif /* _RMI_2D_SENSOR_H */

drivers/input/rmi4/rmi_bus.c

@@ -0,0 +1,419 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/kconfig.h>
+#include <linux/list.h>
+#include <linux/pm.h>
+#include <linux/rmi.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/of.h>
+#include "rmi_bus.h"
+#include "rmi_driver.h"
+
+static int debug_flags;
+module_param(debug_flags, int, 0644);
+MODULE_PARM_DESC(debug_flags, "control debugging information");
+
+void rmi_dbg(int flags, struct device *dev, const char *fmt, ...)
+{
+	struct va_format vaf;
+	va_list args;
+
+	if (flags & debug_flags) {
+		va_start(args, fmt);
+
+		vaf.fmt = fmt;
+		vaf.va = &args;
+
+		dev_printk(KERN_DEBUG, dev, "%pV", &vaf);
+
+		va_end(args);
+	}
+}
+EXPORT_SYMBOL_GPL(rmi_dbg);
+
+/*
+ * RMI Physical devices
+ *
+ * Physical RMI device consists of several functions serving particular
+ * purpose. For example F11 is a 2D touch sensor while F01 is a generic
+ * function present in every RMI device.
+ */
+
+static void rmi_release_device(struct device *dev)
+{
+	struct rmi_device *rmi_dev = to_rmi_device(dev);
+
+	kfree(rmi_dev);
+}
+
+static struct device_type rmi_device_type = {
+	.name		= "rmi4_sensor",
+	.release	= rmi_release_device,
+};
+
+bool rmi_is_physical_device(struct device *dev)
+{
+	return dev->type == &rmi_device_type;
+}
+
+/**
+ * rmi_register_transport_device - register a transport device connection
+ * on the RMI bus.  Transport drivers provide communication from the devices
+ * on a bus (such as SPI, I2C, and so on) to the RMI4 sensor.
+ *
+ * @xport: the transport device to register
+ */
+int rmi_register_transport_device(struct rmi_transport_dev *xport)
+{
+	static atomic_t transport_device_count = ATOMIC_INIT(0);
+	struct rmi_device *rmi_dev;
+	int error;
+
+	rmi_dev = kzalloc(sizeof(struct rmi_device), GFP_KERNEL);
+	if (!rmi_dev)
+		return -ENOMEM;
+
+	device_initialize(&rmi_dev->dev);
+
+	rmi_dev->xport = xport;
+	rmi_dev->number = atomic_inc_return(&transport_device_count) - 1;
+
+	dev_set_name(&rmi_dev->dev, "rmi4-%02d", rmi_dev->number);
+
+	rmi_dev->dev.bus = &rmi_bus_type;
+	rmi_dev->dev.type = &rmi_device_type;
+
+	xport->rmi_dev = rmi_dev;
+
+	error = device_add(&rmi_dev->dev);
+	if (error)
+		goto err_put_device;
+
+	rmi_dbg(RMI_DEBUG_CORE, xport->dev,
+		"%s: Registered %s as %s.\n", __func__,
+		dev_name(rmi_dev->xport->dev), dev_name(&rmi_dev->dev));
+
+	return 0;
+
+err_put_device:
+	put_device(&rmi_dev->dev);
+	return error;
+}
+EXPORT_SYMBOL_GPL(rmi_register_transport_device);
+
+/**
+ * rmi_unregister_transport_device - unregister a transport device connection
+ * @xport: the transport driver to unregister
+ *
+ */
+void rmi_unregister_transport_device(struct rmi_transport_dev *xport)
+{
+	struct rmi_device *rmi_dev = xport->rmi_dev;
+
+	device_del(&rmi_dev->dev);
+	put_device(&rmi_dev->dev);
+}
+EXPORT_SYMBOL(rmi_unregister_transport_device);
+
+
+/* Function specific stuff */
+
+static void rmi_release_function(struct device *dev)
+{
+	struct rmi_function *fn = to_rmi_function(dev);
+
+	kfree(fn);
+}
+
+static struct device_type rmi_function_type = {
+	.name		= "rmi4_function",
+	.release	= rmi_release_function,
+};
+
+bool rmi_is_function_device(struct device *dev)
+{
+	return dev->type == &rmi_function_type;
+}
+
+static int rmi_function_match(struct device *dev, struct device_driver *drv)
+{
+	struct rmi_function_handler *handler = to_rmi_function_handler(drv);
+	struct rmi_function *fn = to_rmi_function(dev);
+
+	return fn->fd.function_number == handler->func;
+}
+
+#ifdef CONFIG_OF
+static void rmi_function_of_probe(struct rmi_function *fn)
+{
+	char of_name[9];
+
+	snprintf(of_name, sizeof(of_name), "rmi4-f%02x",
+		fn->fd.function_number);
+	fn->dev.of_node = of_find_node_by_name(
+				fn->rmi_dev->xport->dev->of_node, of_name);
+}
+#else
+static inline void rmi_function_of_probe(struct rmi_function *fn)
+{}
+#endif
+
+static int rmi_function_probe(struct device *dev)
+{
+	struct rmi_function *fn = to_rmi_function(dev);
+	struct rmi_function_handler *handler =
+					to_rmi_function_handler(dev->driver);
+	int error;
+
+	rmi_function_of_probe(fn);
+
+	if (handler->probe) {
+		error = handler->probe(fn);
+		return error;
+	}
+
+	return 0;
+}
+
+static int rmi_function_remove(struct device *dev)
+{
+	struct rmi_function *fn = to_rmi_function(dev);
+	struct rmi_function_handler *handler =
+					to_rmi_function_handler(dev->driver);
+
+	if (handler->remove)
+		handler->remove(fn);
+
+	return 0;
+}
+
+int rmi_register_function(struct rmi_function *fn)
+{
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	int error;
+
+	device_initialize(&fn->dev);
+
+	dev_set_name(&fn->dev, "%s.fn%02x",
+		     dev_name(&rmi_dev->dev), fn->fd.function_number);
+
+	fn->dev.parent = &rmi_dev->dev;
+	fn->dev.type = &rmi_function_type;
+	fn->dev.bus = &rmi_bus_type;
+
+	error = device_add(&fn->dev);
+	if (error) {
+		dev_err(&rmi_dev->dev,
+			"Failed device_register function device %s\n",
+			dev_name(&fn->dev));
+		goto err_put_device;
+	}
+
+	rmi_dbg(RMI_DEBUG_CORE, &rmi_dev->dev, "Registered F%02X.\n",
+			fn->fd.function_number);
+
+	return 0;
+
+err_put_device:
+	put_device(&fn->dev);
+	return error;
+}
+
+void rmi_unregister_function(struct rmi_function *fn)
+{
+	device_del(&fn->dev);
+
+	if (fn->dev.of_node)
+		of_node_put(fn->dev.of_node);
+
+	put_device(&fn->dev);
+}
+
+/**
+ * rmi_register_function_handler - register a handler for an RMI function
+ * @handler: RMI handler that should be registered.
+ * @module: pointer to module that implements the handler
+ * @mod_name: name of the module implementing the handler
+ *
+ * This function performs additional setup of RMI function handler and
+ * registers it with the RMI core so that it can be bound to
+ * RMI function devices.
+ */
+int __rmi_register_function_handler(struct rmi_function_handler *handler,
+				     struct module *owner,
+				     const char *mod_name)
+{
+	struct device_driver *driver = &handler->driver;
+	int error;
+
+	driver->bus = &rmi_bus_type;
+	driver->owner = owner;
+	driver->mod_name = mod_name;
+	driver->probe = rmi_function_probe;
+	driver->remove = rmi_function_remove;
+
+	error = driver_register(&handler->driver);
+	if (error) {
+		pr_err("driver_register() failed for %s, error: %d\n",
+			handler->driver.name, error);
+		return error;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(__rmi_register_function_handler);
+
+/**
+ * rmi_unregister_function_handler - unregister given RMI function handler
+ * @handler: RMI handler that should be unregistered.
+ *
+ * This function unregisters given function handler from RMI core which
+ * causes it to be unbound from the function devices.
+ */
+void rmi_unregister_function_handler(struct rmi_function_handler *handler)
+{
+	driver_unregister(&handler->driver);
+}
+EXPORT_SYMBOL_GPL(rmi_unregister_function_handler);
+
+/* Bus specific stuff */
+
+static int rmi_bus_match(struct device *dev, struct device_driver *drv)
+{
+	bool physical = rmi_is_physical_device(dev);
+
+	/* First see if types are not compatible */
+	if (physical != rmi_is_physical_driver(drv))
+		return 0;
+
+	return physical || rmi_function_match(dev, drv);
+}
+
+struct bus_type rmi_bus_type = {
+	.match		= rmi_bus_match,
+	.name		= "rmi4",
+};
+
+static struct rmi_function_handler *fn_handlers[] = {
+	&rmi_f01_handler,
+#ifdef CONFIG_RMI4_F11
+	&rmi_f11_handler,
+#endif
+#ifdef CONFIG_RMI4_F12
+	&rmi_f12_handler,
+#endif
+#ifdef CONFIG_RMI4_F30
+	&rmi_f30_handler,
+#endif
+};
+
+static void __rmi_unregister_function_handlers(int start_idx)
+{
+	int i;
+
+	for (i = start_idx; i >= 0; i--)
+		rmi_unregister_function_handler(fn_handlers[i]);
+}
+
+static void rmi_unregister_function_handlers(void)
+{
+	__rmi_unregister_function_handlers(ARRAY_SIZE(fn_handlers) - 1);
+}
+
+static int rmi_register_function_handlers(void)
+{
+	int ret;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(fn_handlers); i++)	{
+		ret = rmi_register_function_handler(fn_handlers[i]);
+		if (ret) {
+			pr_err("%s: error registering the RMI F%02x handler: %d\n",
+				__func__, fn_handlers[i]->func, ret);
+			goto err_unregister_function_handlers;
+		}
+	}
+
+	return 0;
+
+err_unregister_function_handlers:
+	__rmi_unregister_function_handlers(i - 1);
+	return ret;
+}
+
+int rmi_of_property_read_u32(struct device *dev, u32 *result,
+				const char *prop, bool optional)
+{
+	int retval;
+	u32 val = 0;
+
+	retval = of_property_read_u32(dev->of_node, prop, &val);
+	if (retval && (!optional && retval == -EINVAL)) {
+		dev_err(dev, "Failed to get %s value: %d\n",
+			prop, retval);
+		return retval;
+	}
+	*result = val;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(rmi_of_property_read_u32);
+
+static int __init rmi_bus_init(void)
+{
+	int error;
+
+	error = bus_register(&rmi_bus_type);
+	if (error) {
+		pr_err("%s: error registering the RMI bus: %d\n",
+			__func__, error);
+		return error;
+	}
+
+	error = rmi_register_function_handlers();
+	if (error)
+		goto err_unregister_bus;
+
+	error = rmi_register_physical_driver();
+	if (error) {
+		pr_err("%s: error registering the RMI physical driver: %d\n",
+			__func__, error);
+		goto err_unregister_bus;
+	}
+
+	return 0;
+
+err_unregister_bus:
+	bus_unregister(&rmi_bus_type);
+	return error;
+}
+module_init(rmi_bus_init);
+
+static void __exit rmi_bus_exit(void)
+{
+	/*
+	 * We should only ever get here if all drivers are unloaded, so
+	 * all we have to do at this point is unregister ourselves.
+	 */
+
+	rmi_unregister_physical_driver();
+	rmi_unregister_function_handlers();
+	bus_unregister(&rmi_bus_type);
+}
+module_exit(rmi_bus_exit);
+
+MODULE_AUTHOR("Christopher Heiny <cheiny@synaptics.com");
+MODULE_AUTHOR("Andrew Duggan <aduggan@synaptics.com");
+MODULE_DESCRIPTION("RMI bus");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(RMI_DRIVER_VERSION);

drivers/input/rmi4/rmi_bus.h

@@ -0,0 +1,182 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#ifndef _RMI_BUS_H
+#define _RMI_BUS_H
+
+#include <linux/rmi.h>
+
+struct rmi_device;
+
+/**
+ * struct rmi_function - represents the implementation of an RMI4
+ * function for a particular device (basically, a driver for that RMI4 function)
+ *
+ * @fd: The function descriptor of the RMI function
+ * @rmi_dev: Pointer to the RMI device associated with this function container
+ * @dev: The device associated with this particular function.
+ *
+ * @num_of_irqs: The number of irqs needed by this function
+ * @irq_pos: The position in the irq bitfield this function holds
+ * @irq_mask: For convenience, can be used to mask IRQ bits off during ATTN
+ * interrupt handling.
+ *
+ * @node: entry in device's list of functions
+ */
+struct rmi_function {
+	struct rmi_function_descriptor fd;
+	struct rmi_device *rmi_dev;
+	struct device dev;
+	struct list_head node;
+
+	unsigned int num_of_irqs;
+	unsigned int irq_pos;
+	unsigned long irq_mask[];
+};
+
+#define to_rmi_function(d)	container_of(d, struct rmi_function, dev)
+
+bool rmi_is_function_device(struct device *dev);
+
+int __must_check rmi_register_function(struct rmi_function *);
+void rmi_unregister_function(struct rmi_function *);
+
+/**
+ * struct rmi_function_handler - driver routines for a particular RMI function.
+ *
+ * @func: The RMI function number
+ * @reset: Called when a reset of the touch sensor is detected.  The routine
+ * should perform any out-of-the-ordinary reset handling that might be
+ * necessary.  Restoring of touch sensor configuration registers should be
+ * handled in the config() callback, below.
+ * @config: Called when the function container is first initialized, and
+ * after a reset is detected.  This routine should write any necessary
+ * configuration settings to the device.
+ * @attention: Called when the IRQ(s) for the function are set by the touch
+ * sensor.
+ * @suspend: Should perform any required operations to suspend the particular
+ * function.
+ * @resume: Should perform any required operations to resume the particular
+ * function.
+ *
+ * All callbacks are expected to return 0 on success, error code on failure.
+ */
+struct rmi_function_handler {
+	struct device_driver driver;
+
+	u8 func;
+
+	int (*probe)(struct rmi_function *fn);
+	void (*remove)(struct rmi_function *fn);
+	int (*config)(struct rmi_function *fn);
+	int (*reset)(struct rmi_function *fn);
+	int (*attention)(struct rmi_function *fn, unsigned long *irq_bits);
+	int (*suspend)(struct rmi_function *fn);
+	int (*resume)(struct rmi_function *fn);
+};
+
+#define to_rmi_function_handler(d) \
+		container_of(d, struct rmi_function_handler, driver)
+
+int __must_check __rmi_register_function_handler(struct rmi_function_handler *,
+						 struct module *, const char *);
+#define rmi_register_function_handler(handler) \
+	__rmi_register_function_handler(handler, THIS_MODULE, KBUILD_MODNAME)
+
+void rmi_unregister_function_handler(struct rmi_function_handler *);
+
+#define to_rmi_driver(d) \
+	container_of(d, struct rmi_driver, driver)
+
+#define to_rmi_device(d) container_of(d, struct rmi_device, dev)
+
+static inline struct rmi_device_platform_data *
+rmi_get_platform_data(struct rmi_device *d)
+{
+	return &d->xport->pdata;
+}
+
+bool rmi_is_physical_device(struct device *dev);
+
+/**
+ * rmi_read - read a single byte
+ * @d: Pointer to an RMI device
+ * @addr: The address to read from
+ * @buf: The read buffer
+ *
+ * Reads a single byte of data using the underlying transport protocol
+ * into memory pointed by @buf. It returns 0 on success or a negative
+ * error code.
+ */
+static inline int rmi_read(struct rmi_device *d, u16 addr, u8 *buf)
+{
+	return d->xport->ops->read_block(d->xport, addr, buf, 1);
+}
+
+/**
+ * rmi_read_block - read a block of bytes
+ * @d: Pointer to an RMI device
+ * @addr: The start address to read from
+ * @buf: The read buffer
+ * @len: Length of the read buffer
+ *
+ * Reads a block of byte data using the underlying transport protocol
+ * into memory pointed by @buf. It returns 0 on success or a negative
+ * error code.
+ */
+static inline int rmi_read_block(struct rmi_device *d, u16 addr,
+				 void *buf, size_t len)
+{
+	return d->xport->ops->read_block(d->xport, addr, buf, len);
+}
+
+/**
+ * rmi_write - write a single byte
+ * @d: Pointer to an RMI device
+ * @addr: The address to write to
+ * @data: The data to write
+ *
+ * Writes a single byte using the underlying transport protocol. It
+ * returns zero on success or a negative error code.
+ */
+static inline int rmi_write(struct rmi_device *d, u16 addr, u8 data)
+{
+	return d->xport->ops->write_block(d->xport, addr, &data, 1);
+}
+
+/**
+ * rmi_write_block - write a block of bytes
+ * @d: Pointer to an RMI device
+ * @addr: The start address to write to
+ * @buf: The write buffer
+ * @len: Length of the write buffer
+ *
+ * Writes a block of byte data from buf using the underlaying transport
+ * protocol.  It returns the amount of bytes written or a negative error code.
+ */
+static inline int rmi_write_block(struct rmi_device *d, u16 addr,
+				  const void *buf, size_t len)
+{
+	return d->xport->ops->write_block(d->xport, addr, buf, len);
+}
+
+int rmi_for_each_dev(void *data, int (*func)(struct device *dev, void *data));
+
+extern struct bus_type rmi_bus_type;
+
+int rmi_of_property_read_u32(struct device *dev, u32 *result,
+				const char *prop, bool optional);
+
+#define RMI_DEBUG_CORE			BIT(0)
+#define RMI_DEBUG_XPORT			BIT(1)
+#define RMI_DEBUG_FN			BIT(2)
+#define RMI_DEBUG_2D_SENSOR		BIT(3)
+
+void rmi_dbg(int flags, struct device *dev, const char *fmt, ...);
+#endif

drivers/input/rmi4/rmi_driver.c

@@ -0,0 +1,1055 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This driver provides the core support for a single RMI4-based device.
+ *
+ * The RMI4 specification can be found here (URL split for line length):
+ *
+ * http://www.synaptics.com/sites/default/files/
+ *      511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/bitmap.h>
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/kconfig.h>
+#include <linux/pm.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <uapi/linux/input.h>
+#include <linux/rmi.h>
+#include "rmi_bus.h"
+#include "rmi_driver.h"
+
+#define HAS_NONSTANDARD_PDT_MASK 0x40
+#define RMI4_MAX_PAGE 0xff
+#define RMI4_PAGE_SIZE 0x100
+#define RMI4_PAGE_MASK 0xFF00
+
+#define RMI_DEVICE_RESET_CMD	0x01
+#define DEFAULT_RESET_DELAY_MS	100
+
+static void rmi_free_function_list(struct rmi_device *rmi_dev)
+{
+	struct rmi_function *fn, *tmp;
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+
+	data->f01_container = NULL;
+
+	/* Doing it in the reverse order so F01 will be removed last */
+	list_for_each_entry_safe_reverse(fn, tmp,
+					 &data->function_list, node) {
+		list_del(&fn->node);
+		rmi_unregister_function(fn);
+	}
+}
+
+static int reset_one_function(struct rmi_function *fn)
+{
+	struct rmi_function_handler *fh;
+	int retval = 0;
+
+	if (!fn || !fn->dev.driver)
+		return 0;
+
+	fh = to_rmi_function_handler(fn->dev.driver);
+	if (fh->reset) {
+		retval = fh->reset(fn);
+		if (retval < 0)
+			dev_err(&fn->dev, "Reset failed with code %d.\n",
+				retval);
+	}
+
+	return retval;
+}
+
+static int configure_one_function(struct rmi_function *fn)
+{
+	struct rmi_function_handler *fh;
+	int retval = 0;
+
+	if (!fn || !fn->dev.driver)
+		return 0;
+
+	fh = to_rmi_function_handler(fn->dev.driver);
+	if (fh->config) {
+		retval = fh->config(fn);
+		if (retval < 0)
+			dev_err(&fn->dev, "Config failed with code %d.\n",
+				retval);
+	}
+
+	return retval;
+}
+
+static int rmi_driver_process_reset_requests(struct rmi_device *rmi_dev)
+{
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	struct rmi_function *entry;
+	int retval;
+
+	list_for_each_entry(entry, &data->function_list, node) {
+		retval = reset_one_function(entry);
+		if (retval < 0)
+			return retval;
+	}
+
+	return 0;
+}
+
+static int rmi_driver_process_config_requests(struct rmi_device *rmi_dev)
+{
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	struct rmi_function *entry;
+	int retval;
+
+	list_for_each_entry(entry, &data->function_list, node) {
+		retval = configure_one_function(entry);
+		if (retval < 0)
+			return retval;
+	}
+
+	return 0;
+}
+
+static void process_one_interrupt(struct rmi_driver_data *data,
+				  struct rmi_function *fn)
+{
+	struct rmi_function_handler *fh;
+
+	if (!fn || !fn->dev.driver)
+		return;
+
+	fh = to_rmi_function_handler(fn->dev.driver);
+	if (fn->irq_mask && fh->attention) {
+		bitmap_and(data->fn_irq_bits, data->irq_status, fn->irq_mask,
+				data->irq_count);
+		if (!bitmap_empty(data->fn_irq_bits, data->irq_count))
+			fh->attention(fn, data->fn_irq_bits);
+	}
+}
+
+int rmi_process_interrupt_requests(struct rmi_device *rmi_dev)
+{
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	struct device *dev = &rmi_dev->dev;
+	struct rmi_function *entry;
+	int error;
+
+	if (!data)
+		return 0;
+
+	if (!rmi_dev->xport->attn_data) {
+		error = rmi_read_block(rmi_dev,
+				data->f01_container->fd.data_base_addr + 1,
+				data->irq_status, data->num_of_irq_regs);
+		if (error < 0) {
+			dev_err(dev, "Failed to read irqs, code=%d\n", error);
+			return error;
+		}
+	}
+
+	mutex_lock(&data->irq_mutex);
+	bitmap_and(data->irq_status, data->irq_status, data->current_irq_mask,
+	       data->irq_count);
+	/*
+	 * At this point, irq_status has all bits that are set in the
+	 * interrupt status register and are enabled.
+	 */
+	mutex_unlock(&data->irq_mutex);
+
+	/*
+	 * It would be nice to be able to use irq_chip to handle these
+	 * nested IRQs.  Unfortunately, most of the current customers for
+	 * this driver are using older kernels (3.0.x) that don't support
+	 * the features required for that.  Once they've shifted to more
+	 * recent kernels (say, 3.3 and higher), this should be switched to
+	 * use irq_chip.
+	 */
+	list_for_each_entry(entry, &data->function_list, node)
+		if (entry->irq_mask)
+			process_one_interrupt(data, entry);
+
+	if (data->input)
+		input_sync(data->input);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(rmi_process_interrupt_requests);
+
+static int suspend_one_function(struct rmi_function *fn)
+{
+	struct rmi_function_handler *fh;
+	int retval = 0;
+
+	if (!fn || !fn->dev.driver)
+		return 0;
+
+	fh = to_rmi_function_handler(fn->dev.driver);
+	if (fh->suspend) {
+		retval = fh->suspend(fn);
+		if (retval < 0)
+			dev_err(&fn->dev, "Suspend failed with code %d.\n",
+				retval);
+	}
+
+	return retval;
+}
+
+static int rmi_suspend_functions(struct rmi_device *rmi_dev)
+{
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	struct rmi_function *entry;
+	int retval;
+
+	list_for_each_entry(entry, &data->function_list, node) {
+		retval = suspend_one_function(entry);
+		if (retval < 0)
+			return retval;
+	}
+
+	return 0;
+}
+
+static int resume_one_function(struct rmi_function *fn)
+{
+	struct rmi_function_handler *fh;
+	int retval = 0;
+
+	if (!fn || !fn->dev.driver)
+		return 0;
+
+	fh = to_rmi_function_handler(fn->dev.driver);
+	if (fh->resume) {
+		retval = fh->resume(fn);
+		if (retval < 0)
+			dev_err(&fn->dev, "Resume failed with code %d.\n",
+				retval);
+	}
+
+	return retval;
+}
+
+static int rmi_resume_functions(struct rmi_device *rmi_dev)
+{
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	struct rmi_function *entry;
+	int retval;
+
+	list_for_each_entry(entry, &data->function_list, node) {
+		retval = resume_one_function(entry);
+		if (retval < 0)
+			return retval;
+	}
+
+	return 0;
+}
+
+static int enable_sensor(struct rmi_device *rmi_dev)
+{
+	int retval = 0;
+
+	retval = rmi_driver_process_config_requests(rmi_dev);
+	if (retval < 0)
+		return retval;
+
+	return rmi_process_interrupt_requests(rmi_dev);
+}
+
+/**
+ * rmi_driver_set_input_params - set input device id and other data.
+ *
+ * @rmi_dev: Pointer to an RMI device
+ * @input: Pointer to input device
+ *
+ */
+static int rmi_driver_set_input_params(struct rmi_device *rmi_dev,
+				struct input_dev *input)
+{
+	input->name = SYNAPTICS_INPUT_DEVICE_NAME;
+	input->id.vendor  = SYNAPTICS_VENDOR_ID;
+	input->id.bustype = BUS_RMI;
+	return 0;
+}
+
+static void rmi_driver_set_input_name(struct rmi_device *rmi_dev,
+				struct input_dev *input)
+{
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	char *device_name = rmi_f01_get_product_ID(data->f01_container);
+	char *name;
+
+	name = devm_kasprintf(&rmi_dev->dev, GFP_KERNEL,
+			      "Synaptics %s", device_name);
+	if (!name)
+		return;
+
+	input->name = name;
+}
+
+static int rmi_driver_set_irq_bits(struct rmi_device *rmi_dev,
+				   unsigned long *mask)
+{
+	int error = 0;
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	struct device *dev = &rmi_dev->dev;
+
+	mutex_lock(&data->irq_mutex);
+	bitmap_or(data->new_irq_mask,
+		  data->current_irq_mask, mask, data->irq_count);
+
+	error = rmi_write_block(rmi_dev,
+			data->f01_container->fd.control_base_addr + 1,
+			data->new_irq_mask, data->num_of_irq_regs);
+	if (error < 0) {
+		dev_err(dev, "%s: Failed to change enabled interrupts!",
+							__func__);
+		goto error_unlock;
+	}
+	bitmap_copy(data->current_irq_mask, data->new_irq_mask,
+		    data->num_of_irq_regs);
+
+error_unlock:
+	mutex_unlock(&data->irq_mutex);
+	return error;
+}
+
+static int rmi_driver_clear_irq_bits(struct rmi_device *rmi_dev,
+				     unsigned long *mask)
+{
+	int error = 0;
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	struct device *dev = &rmi_dev->dev;
+
+	mutex_lock(&data->irq_mutex);
+	bitmap_andnot(data->new_irq_mask,
+		  data->current_irq_mask, mask, data->irq_count);
+
+	error = rmi_write_block(rmi_dev,
+			data->f01_container->fd.control_base_addr + 1,
+			data->new_irq_mask, data->num_of_irq_regs);
+	if (error < 0) {
+		dev_err(dev, "%s: Failed to change enabled interrupts!",
+							__func__);
+		goto error_unlock;
+	}
+	bitmap_copy(data->current_irq_mask, data->new_irq_mask,
+		    data->num_of_irq_regs);
+
+error_unlock:
+	mutex_unlock(&data->irq_mutex);
+	return error;
+}
+
+static int rmi_driver_reset_handler(struct rmi_device *rmi_dev)
+{
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	int error;
+
+	/*
+	 * Can get called before the driver is fully ready to deal with
+	 * this situation.
+	 */
+	if (!data || !data->f01_container) {
+		dev_warn(&rmi_dev->dev,
+			 "Not ready to handle reset yet!\n");
+		return 0;
+	}
+
+	error = rmi_read_block(rmi_dev,
+			       data->f01_container->fd.control_base_addr + 1,
+			       data->current_irq_mask, data->num_of_irq_regs);
+	if (error < 0) {
+		dev_err(&rmi_dev->dev, "%s: Failed to read current IRQ mask.\n",
+			__func__);
+		return error;
+	}
+
+	error = rmi_driver_process_reset_requests(rmi_dev);
+	if (error < 0)
+		return error;
+
+	error = rmi_driver_process_config_requests(rmi_dev);
+	if (error < 0)
+		return error;
+
+	return 0;
+}
+
+int rmi_read_pdt_entry(struct rmi_device *rmi_dev, struct pdt_entry *entry,
+			u16 pdt_address)
+{
+	u8 buf[RMI_PDT_ENTRY_SIZE];
+	int error;
+
+	error = rmi_read_block(rmi_dev, pdt_address, buf, RMI_PDT_ENTRY_SIZE);
+	if (error) {
+		dev_err(&rmi_dev->dev, "Read PDT entry at %#06x failed, code: %d.\n",
+				pdt_address, error);
+		return error;
+	}
+
+	entry->page_start = pdt_address & RMI4_PAGE_MASK;
+	entry->query_base_addr = buf[0];
+	entry->command_base_addr = buf[1];
+	entry->control_base_addr = buf[2];
+	entry->data_base_addr = buf[3];
+	entry->interrupt_source_count = buf[4] & RMI_PDT_INT_SOURCE_COUNT_MASK;
+	entry->function_version = (buf[4] & RMI_PDT_FUNCTION_VERSION_MASK) >> 5;
+	entry->function_number = buf[5];
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(rmi_read_pdt_entry);
+
+static void rmi_driver_copy_pdt_to_fd(const struct pdt_entry *pdt,
+				      struct rmi_function_descriptor *fd)
+{
+	fd->query_base_addr = pdt->query_base_addr + pdt->page_start;
+	fd->command_base_addr = pdt->command_base_addr + pdt->page_start;
+	fd->control_base_addr = pdt->control_base_addr + pdt->page_start;
+	fd->data_base_addr = pdt->data_base_addr + pdt->page_start;
+	fd->function_number = pdt->function_number;
+	fd->interrupt_source_count = pdt->interrupt_source_count;
+	fd->function_version = pdt->function_version;
+}
+
+#define RMI_SCAN_CONTINUE	0
+#define RMI_SCAN_DONE		1
+
+static int rmi_scan_pdt_page(struct rmi_device *rmi_dev,
+			     int page,
+			     void *ctx,
+			     int (*callback)(struct rmi_device *rmi_dev,
+					     void *ctx,
+					     const struct pdt_entry *entry))
+{
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	struct pdt_entry pdt_entry;
+	u16 page_start = RMI4_PAGE_SIZE * page;
+	u16 pdt_start = page_start + PDT_START_SCAN_LOCATION;
+	u16 pdt_end = page_start + PDT_END_SCAN_LOCATION;
+	u16 addr;
+	int error;
+	int retval;
+
+	for (addr = pdt_start; addr >= pdt_end; addr -= RMI_PDT_ENTRY_SIZE) {
+		error = rmi_read_pdt_entry(rmi_dev, &pdt_entry, addr);
+		if (error)
+			return error;
+
+		if (RMI4_END_OF_PDT(pdt_entry.function_number))
+			break;
+
+		retval = callback(rmi_dev, ctx, &pdt_entry);
+		if (retval != RMI_SCAN_CONTINUE)
+			return retval;
+	}
+
+	return (data->f01_bootloader_mode || addr == pdt_start) ?
+					RMI_SCAN_DONE : RMI_SCAN_CONTINUE;
+}
+
+static int rmi_scan_pdt(struct rmi_device *rmi_dev, void *ctx,
+			int (*callback)(struct rmi_device *rmi_dev,
+					void *ctx,
+					const struct pdt_entry *entry))
+{
+	int page;
+	int retval = RMI_SCAN_DONE;
+
+	for (page = 0; page <= RMI4_MAX_PAGE; page++) {
+		retval = rmi_scan_pdt_page(rmi_dev, page, ctx, callback);
+		if (retval != RMI_SCAN_CONTINUE)
+			break;
+	}
+
+	return retval < 0 ? retval : 0;
+}
+
+int rmi_read_register_desc(struct rmi_device *d, u16 addr,
+				struct rmi_register_descriptor *rdesc)
+{
+	int ret;
+	u8 size_presence_reg;
+	u8 buf[35];
+	int presense_offset = 1;
+	u8 *struct_buf;
+	int reg;
+	int offset = 0;
+	int map_offset = 0;
+	int i;
+	int b;
+
+	/*
+	 * The first register of the register descriptor is the size of
+	 * the register descriptor's presense register.
+	 */
+	ret = rmi_read(d, addr, &size_presence_reg);
+	if (ret)
+		return ret;
+	++addr;
+
+	if (size_presence_reg < 0 || size_presence_reg > 35)
+		return -EIO;
+
+	memset(buf, 0, sizeof(buf));
+
+	/*
+	 * The presence register contains the size of the register structure
+	 * and a bitmap which identified which packet registers are present
+	 * for this particular register type (ie query, control, or data).
+	 */
+	ret = rmi_read_block(d, addr, buf, size_presence_reg);
+	if (ret)
+		return ret;
+	++addr;
+
+	if (buf[0] == 0) {
+		presense_offset = 3;
+		rdesc->struct_size = buf[1] | (buf[2] << 8);
+	} else {
+		rdesc->struct_size = buf[0];
+	}
+
+	for (i = presense_offset; i < size_presence_reg; i++) {
+		for (b = 0; b < 8; b++) {
+			if (buf[i] & (0x1 << b))
+				bitmap_set(rdesc->presense_map, map_offset, 1);
+			++map_offset;
+		}
+	}
+
+	rdesc->num_registers = bitmap_weight(rdesc->presense_map,
+						RMI_REG_DESC_PRESENSE_BITS);
+
+	rdesc->registers = devm_kzalloc(&d->dev, rdesc->num_registers *
+				sizeof(struct rmi_register_desc_item),
+				GFP_KERNEL);
+	if (!rdesc->registers)
+		return -ENOMEM;
+
+	/*
+	 * Allocate a temporary buffer to hold the register structure.
+	 * I'm not using devm_kzalloc here since it will not be retained
+	 * after exiting this function
+	 */
+	struct_buf = kzalloc(rdesc->struct_size, GFP_KERNEL);
+	if (!struct_buf)
+		return -ENOMEM;
+
+	/*
+	 * The register structure contains information about every packet
+	 * register of this type. This includes the size of the packet
+	 * register and a bitmap of all subpackets contained in the packet
+	 * register.
+	 */
+	ret = rmi_read_block(d, addr, struct_buf, rdesc->struct_size);
+	if (ret)
+		goto free_struct_buff;
+
+	reg = find_first_bit(rdesc->presense_map, RMI_REG_DESC_PRESENSE_BITS);
+	map_offset = 0;
+	for (i = 0; i < rdesc->num_registers; i++) {
+		struct rmi_register_desc_item *item = &rdesc->registers[i];
+		int reg_size = struct_buf[offset];
+
+		++offset;
+		if (reg_size == 0) {
+			reg_size = struct_buf[offset] |
+					(struct_buf[offset + 1] << 8);
+			offset += 2;
+		}
+
+		if (reg_size == 0) {
+			reg_size = struct_buf[offset] |
+					(struct_buf[offset + 1] << 8) |
+					(struct_buf[offset + 2] << 16) |
+					(struct_buf[offset + 3] << 24);
+			offset += 4;
+		}
+
+		item->reg = reg;
+		item->reg_size = reg_size;
+
+		do {
+			for (b = 0; b < 7; b++) {
+				if (struct_buf[offset] & (0x1 << b))
+					bitmap_set(item->subpacket_map,
+						map_offset, 1);
+				++map_offset;
+			}
+		} while (struct_buf[offset++] & 0x80);
+
+		item->num_subpackets = bitmap_weight(item->subpacket_map,
+						RMI_REG_DESC_SUBPACKET_BITS);
+
+		rmi_dbg(RMI_DEBUG_CORE, &d->dev,
+			"%s: reg: %d reg size: %ld subpackets: %d\n", __func__,
+			item->reg, item->reg_size, item->num_subpackets);
+
+		reg = find_next_bit(rdesc->presense_map,
+				RMI_REG_DESC_PRESENSE_BITS, reg + 1);
+	}
+
+free_struct_buff:
+	kfree(struct_buf);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(rmi_read_register_desc);
+
+const struct rmi_register_desc_item *rmi_get_register_desc_item(
+				struct rmi_register_descriptor *rdesc, u16 reg)
+{
+	const struct rmi_register_desc_item *item;
+	int i;
+
+	for (i = 0; i < rdesc->num_registers; i++) {
+		item = &rdesc->registers[i];
+		if (item->reg == reg)
+			return item;
+	}
+
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(rmi_get_register_desc_item);
+
+size_t rmi_register_desc_calc_size(struct rmi_register_descriptor *rdesc)
+{
+	const struct rmi_register_desc_item *item;
+	int i;
+	size_t size = 0;
+
+	for (i = 0; i < rdesc->num_registers; i++) {
+		item = &rdesc->registers[i];
+		size += item->reg_size;
+	}
+	return size;
+}
+EXPORT_SYMBOL_GPL(rmi_register_desc_calc_size);
+
+/* Compute the register offset relative to the base address */
+int rmi_register_desc_calc_reg_offset(
+		struct rmi_register_descriptor *rdesc, u16 reg)
+{
+	const struct rmi_register_desc_item *item;
+	int offset = 0;
+	int i;
+
+	for (i = 0; i < rdesc->num_registers; i++) {
+		item = &rdesc->registers[i];
+		if (item->reg == reg)
+			return offset;
+		++offset;
+	}
+	return -1;
+}
+EXPORT_SYMBOL_GPL(rmi_register_desc_calc_reg_offset);
+
+bool rmi_register_desc_has_subpacket(const struct rmi_register_desc_item *item,
+	u8 subpacket)
+{
+	return find_next_bit(item->subpacket_map, RMI_REG_DESC_PRESENSE_BITS,
+				subpacket) == subpacket;
+}
+
+/* Indicates that flash programming is enabled (bootloader mode). */
+#define RMI_F01_STATUS_BOOTLOADER(status)	(!!((status) & 0x40))
+
+/*
+ * Given the PDT entry for F01, read the device status register to determine
+ * if we're stuck in bootloader mode or not.
+ *
+ */
+static int rmi_check_bootloader_mode(struct rmi_device *rmi_dev,
+				     const struct pdt_entry *pdt)
+{
+	int error;
+	u8 device_status;
+
+	error = rmi_read(rmi_dev, pdt->data_base_addr + pdt->page_start,
+			 &device_status);
+	if (error) {
+		dev_err(&rmi_dev->dev,
+			"Failed to read device status: %d.\n", error);
+		return error;
+	}
+
+	return RMI_F01_STATUS_BOOTLOADER(device_status);
+}
+
+static int rmi_count_irqs(struct rmi_device *rmi_dev,
+			 void *ctx, const struct pdt_entry *pdt)
+{
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	int *irq_count = ctx;
+
+	*irq_count += pdt->interrupt_source_count;
+	if (pdt->function_number == 0x01) {
+		data->f01_bootloader_mode =
+			rmi_check_bootloader_mode(rmi_dev, pdt);
+		if (data->f01_bootloader_mode)
+			dev_warn(&rmi_dev->dev,
+				"WARNING: RMI4 device is in bootloader mode!\n");
+	}
+
+	return RMI_SCAN_CONTINUE;
+}
+
+static int rmi_initial_reset(struct rmi_device *rmi_dev,
+			     void *ctx, const struct pdt_entry *pdt)
+{
+	int error;
+
+	if (pdt->function_number == 0x01) {
+		u16 cmd_addr = pdt->page_start + pdt->command_base_addr;
+		u8 cmd_buf = RMI_DEVICE_RESET_CMD;
+		const struct rmi_device_platform_data *pdata =
+				rmi_get_platform_data(rmi_dev);
+
+		if (rmi_dev->xport->ops->reset) {
+			error = rmi_dev->xport->ops->reset(rmi_dev->xport,
+								cmd_addr);
+			if (error)
+				return error;
+
+			return RMI_SCAN_DONE;
+		}
+
+		error = rmi_write_block(rmi_dev, cmd_addr, &cmd_buf, 1);
+		if (error) {
+			dev_err(&rmi_dev->dev,
+				"Initial reset failed. Code = %d.\n", error);
+			return error;
+		}
+
+		mdelay(pdata->reset_delay_ms ?: DEFAULT_RESET_DELAY_MS);
+
+		return RMI_SCAN_DONE;
+	}
+
+	/* F01 should always be on page 0. If we don't find it there, fail. */
+	return pdt->page_start == 0 ? RMI_SCAN_CONTINUE : -ENODEV;
+}
+
+static int rmi_create_function(struct rmi_device *rmi_dev,
+			       void *ctx, const struct pdt_entry *pdt)
+{
+	struct device *dev = &rmi_dev->dev;
+	struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
+	int *current_irq_count = ctx;
+	struct rmi_function *fn;
+	int i;
+	int error;
+
+	rmi_dbg(RMI_DEBUG_CORE, dev, "Initializing F%02X.\n",
+			pdt->function_number);
+
+	fn = kzalloc(sizeof(struct rmi_function) +
+			BITS_TO_LONGS(data->irq_count) * sizeof(unsigned long),
+		     GFP_KERNEL);
+	if (!fn) {
+		dev_err(dev, "Failed to allocate memory for F%02X\n",
+			pdt->function_number);
+		return -ENOMEM;
+	}
+
+	INIT_LIST_HEAD(&fn->node);
+	rmi_driver_copy_pdt_to_fd(pdt, &fn->fd);
+
+	fn->rmi_dev = rmi_dev;
+
+	fn->num_of_irqs = pdt->interrupt_source_count;
+	fn->irq_pos = *current_irq_count;
+	*current_irq_count += fn->num_of_irqs;
+
+	for (i = 0; i < fn->num_of_irqs; i++)
+		set_bit(fn->irq_pos + i, fn->irq_mask);
+
+	error = rmi_register_function(fn);
+	if (error)
+		goto err_put_fn;
+
+	if (pdt->function_number == 0x01)
+		data->f01_container = fn;
+
+	list_add_tail(&fn->node, &data->function_list);
+
+	return RMI_SCAN_CONTINUE;
+
+err_put_fn:
+	put_device(&fn->dev);
+	return error;
+}
+
+int rmi_driver_suspend(struct rmi_device *rmi_dev)
+{
+	int retval = 0;
+
+	retval = rmi_suspend_functions(rmi_dev);
+	if (retval)
+		dev_warn(&rmi_dev->dev, "Failed to suspend functions: %d\n",
+			retval);
+
+	return retval;
+}
+EXPORT_SYMBOL_GPL(rmi_driver_suspend);
+
+int rmi_driver_resume(struct rmi_device *rmi_dev)
+{
+	int retval;
+
+	retval = rmi_resume_functions(rmi_dev);
+	if (retval)
+		dev_warn(&rmi_dev->dev, "Failed to suspend functions: %d\n",
+			retval);
+
+	return retval;
+}
+EXPORT_SYMBOL_GPL(rmi_driver_resume);
+
+static int rmi_driver_remove(struct device *dev)
+{
+	struct rmi_device *rmi_dev = to_rmi_device(dev);
+
+	rmi_free_function_list(rmi_dev);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static int rmi_driver_of_probe(struct device *dev,
+				struct rmi_device_platform_data *pdata)
+{
+	int retval;
+
+	retval = rmi_of_property_read_u32(dev, &pdata->reset_delay_ms,
+					"syna,reset-delay-ms", 1);
+	if (retval)
+		return retval;
+
+	return 0;
+}
+#else
+static inline int rmi_driver_of_probe(struct device *dev,
+					struct rmi_device_platform_data *pdata)
+{
+	return -ENODEV;
+}
+#endif
+
+static int rmi_driver_probe(struct device *dev)
+{
+	struct rmi_driver *rmi_driver;
+	struct rmi_driver_data *data;
+	struct rmi_device_platform_data *pdata;
+	struct rmi_device *rmi_dev;
+	size_t size;
+	void *irq_memory;
+	int irq_count;
+	int retval;
+
+	rmi_dbg(RMI_DEBUG_CORE, dev, "%s: Starting probe.\n",
+			__func__);
+
+	if (!rmi_is_physical_device(dev)) {
+		rmi_dbg(RMI_DEBUG_CORE, dev, "Not a physical device.\n");
+		return -ENODEV;
+	}
+
+	rmi_dev = to_rmi_device(dev);
+	rmi_driver = to_rmi_driver(dev->driver);
+	rmi_dev->driver = rmi_driver;
+
+	pdata = rmi_get_platform_data(rmi_dev);
+
+	if (rmi_dev->xport->dev->of_node) {
+		retval = rmi_driver_of_probe(rmi_dev->xport->dev, pdata);
+		if (retval)
+			return retval;
+	}
+
+	data = devm_kzalloc(dev, sizeof(struct rmi_driver_data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&data->function_list);
+	data->rmi_dev = rmi_dev;
+	dev_set_drvdata(&rmi_dev->dev, data);
+
+	/*
+	 * Right before a warm boot, the sensor might be in some unusual state,
+	 * such as F54 diagnostics, or F34 bootloader mode after a firmware
+	 * or configuration update.  In order to clear the sensor to a known
+	 * state and/or apply any updates, we issue a initial reset to clear any
+	 * previous settings and force it into normal operation.
+	 *
+	 * We have to do this before actually building the PDT because
+	 * the reflash updates (if any) might cause various registers to move
+	 * around.
+	 *
+	 * For a number of reasons, this initial reset may fail to return
+	 * within the specified time, but we'll still be able to bring up the
+	 * driver normally after that failure.  This occurs most commonly in
+	 * a cold boot situation (where then firmware takes longer to come up
+	 * than from a warm boot) and the reset_delay_ms in the platform data
+	 * has been set too short to accommodate that.  Since the sensor will
+	 * eventually come up and be usable, we don't want to just fail here
+	 * and leave the customer's device unusable.  So we warn them, and
+	 * continue processing.
+	 */
+	retval = rmi_scan_pdt(rmi_dev, NULL, rmi_initial_reset);
+	if (retval < 0)
+		dev_warn(dev, "RMI initial reset failed! Continuing in spite of this.\n");
+
+	retval = rmi_read(rmi_dev, PDT_PROPERTIES_LOCATION, &data->pdt_props);
+	if (retval < 0) {
+		/*
+		 * we'll print out a warning and continue since
+		 * failure to get the PDT properties is not a cause to fail
+		 */
+		dev_warn(dev, "Could not read PDT properties from %#06x (code %d). Assuming 0x00.\n",
+			 PDT_PROPERTIES_LOCATION, retval);
+	}
+
+	/*
+	 * We need to count the IRQs and allocate their storage before scanning
+	 * the PDT and creating the function entries, because adding a new
+	 * function can trigger events that result in the IRQ related storage
+	 * being accessed.
+	 */
+	rmi_dbg(RMI_DEBUG_CORE, dev, "Counting IRQs.\n");
+	irq_count = 0;
+	retval = rmi_scan_pdt(rmi_dev, &irq_count, rmi_count_irqs);
+	if (retval < 0) {
+		dev_err(dev, "IRQ counting failed with code %d.\n", retval);
+		goto err;
+	}
+	data->irq_count = irq_count;
+	data->num_of_irq_regs = (data->irq_count + 7) / 8;
+
+	mutex_init(&data->irq_mutex);
+
+	size = BITS_TO_LONGS(data->irq_count) * sizeof(unsigned long);
+	irq_memory = devm_kzalloc(dev, size * 4, GFP_KERNEL);
+	if (!irq_memory) {
+		dev_err(dev, "Failed to allocate memory for irq masks.\n");
+		goto err;
+	}
+
+	data->irq_status	= irq_memory + size * 0;
+	data->fn_irq_bits	= irq_memory + size * 1;
+	data->current_irq_mask	= irq_memory + size * 2;
+	data->new_irq_mask	= irq_memory + size * 3;
+
+	if (rmi_dev->xport->input) {
+		/*
+		 * The transport driver already has an input device.
+		 * In some cases it is preferable to reuse the transport
+		 * devices input device instead of creating a new one here.
+		 * One example is some HID touchpads report "pass-through"
+		 * button events are not reported by rmi registers.
+		 */
+		data->input = rmi_dev->xport->input;
+	} else {
+		data->input = devm_input_allocate_device(dev);
+		if (!data->input) {
+			dev_err(dev, "%s: Failed to allocate input device.\n",
+				__func__);
+			retval = -ENOMEM;
+			goto err_destroy_functions;
+		}
+		rmi_driver_set_input_params(rmi_dev, data->input);
+		data->input->phys = devm_kasprintf(dev, GFP_KERNEL,
+						"%s/input0", dev_name(dev));
+	}
+
+	irq_count = 0;
+	rmi_dbg(RMI_DEBUG_CORE, dev, "Creating functions.");
+	retval = rmi_scan_pdt(rmi_dev, &irq_count, rmi_create_function);
+	if (retval < 0) {
+		dev_err(dev, "Function creation failed with code %d.\n",
+			retval);
+		goto err_destroy_functions;
+	}
+
+	if (!data->f01_container) {
+		dev_err(dev, "Missing F01 container!\n");
+		retval = -EINVAL;
+		goto err_destroy_functions;
+	}
+
+	retval = rmi_read_block(rmi_dev,
+				data->f01_container->fd.control_base_addr + 1,
+				data->current_irq_mask, data->num_of_irq_regs);
+	if (retval < 0) {
+		dev_err(dev, "%s: Failed to read current IRQ mask.\n",
+			__func__);
+		goto err_destroy_functions;
+	}
+
+	if (data->input) {
+		rmi_driver_set_input_name(rmi_dev, data->input);
+		if (!rmi_dev->xport->input) {
+			if (input_register_device(data->input)) {
+				dev_err(dev, "%s: Failed to register input device.\n",
+					__func__);
+				goto err_destroy_functions;
+			}
+		}
+	}
+
+	if (data->f01_container->dev.driver)
+		/* Driver already bound, so enable ATTN now. */
+		return enable_sensor(rmi_dev);
+
+	return 0;
+
+err_destroy_functions:
+	rmi_free_function_list(rmi_dev);
+err:
+	return retval < 0 ? retval : 0;
+}
+
+static struct rmi_driver rmi_physical_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= "rmi4_physical",
+		.bus	= &rmi_bus_type,
+		.probe = rmi_driver_probe,
+		.remove = rmi_driver_remove,
+	},
+	.reset_handler = rmi_driver_reset_handler,
+	.clear_irq_bits = rmi_driver_clear_irq_bits,
+	.set_irq_bits = rmi_driver_set_irq_bits,
+	.set_input_params = rmi_driver_set_input_params,
+};
+
+bool rmi_is_physical_driver(struct device_driver *drv)
+{
+	return drv == &rmi_physical_driver.driver;
+}
+
+int __init rmi_register_physical_driver(void)
+{
+	int error;
+
+	error = driver_register(&rmi_physical_driver.driver);
+	if (error) {
+		pr_err("%s: driver register failed, code=%d.\n", __func__,
+		       error);
+		return error;
+	}
+
+	return 0;
+}
+
+void __exit rmi_unregister_physical_driver(void)
+{
+	driver_unregister(&rmi_physical_driver.driver);
+}

drivers/input/rmi4/rmi_driver.h

@@ -0,0 +1,105 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#ifndef _RMI_DRIVER_H
+#define _RMI_DRIVER_H
+
+#include <linux/ctype.h>
+#include <linux/hrtimer.h>
+#include <linux/ktime.h>
+#include <linux/input.h>
+#include "rmi_bus.h"
+
+#define RMI_DRIVER_VERSION "2.0"
+
+#define SYNAPTICS_INPUT_DEVICE_NAME "Synaptics RMI4 Touch Sensor"
+#define SYNAPTICS_VENDOR_ID 0x06cb
+
+#define GROUP(_attrs) { \
+	.attrs = _attrs,  \
+}
+
+#define PDT_PROPERTIES_LOCATION 0x00EF
+#define BSR_LOCATION 0x00FE
+
+#define RMI_PDT_PROPS_HAS_BSR 0x02
+
+#define NAME_BUFFER_SIZE 256
+
+#define RMI_PDT_ENTRY_SIZE 6
+#define RMI_PDT_FUNCTION_VERSION_MASK   0x60
+#define RMI_PDT_INT_SOURCE_COUNT_MASK   0x07
+
+#define PDT_START_SCAN_LOCATION 0x00e9
+#define PDT_END_SCAN_LOCATION	0x0005
+#define RMI4_END_OF_PDT(id) ((id) == 0x00 || (id) == 0xff)
+
+struct pdt_entry {
+	u16 page_start;
+	u8 query_base_addr;
+	u8 command_base_addr;
+	u8 control_base_addr;
+	u8 data_base_addr;
+	u8 interrupt_source_count;
+	u8 function_version;
+	u8 function_number;
+};
+
+int rmi_read_pdt_entry(struct rmi_device *rmi_dev, struct pdt_entry *entry,
+			u16 pdt_address);
+
+#define RMI_REG_DESC_PRESENSE_BITS	(32 * BITS_PER_BYTE)
+#define RMI_REG_DESC_SUBPACKET_BITS	(37 * BITS_PER_BYTE)
+
+/* describes a single packet register */
+struct rmi_register_desc_item {
+	u16 reg;
+	unsigned long reg_size;
+	u8 num_subpackets;
+	unsigned long subpacket_map[BITS_TO_LONGS(
+				RMI_REG_DESC_SUBPACKET_BITS)];
+};
+
+/*
+ * describes the packet registers for a particular type
+ * (ie query, control, data)
+ */
+struct rmi_register_descriptor {
+	unsigned long struct_size;
+	unsigned long presense_map[BITS_TO_LONGS(RMI_REG_DESC_PRESENSE_BITS)];
+	u8 num_registers;
+	struct rmi_register_desc_item *registers;
+};
+
+int rmi_read_register_desc(struct rmi_device *d, u16 addr,
+				struct rmi_register_descriptor *rdesc);
+const struct rmi_register_desc_item *rmi_get_register_desc_item(
+				struct rmi_register_descriptor *rdesc, u16 reg);
+
+/*
+ * Calculate the total size of all of the registers described in the
+ * descriptor.
+ */
+size_t rmi_register_desc_calc_size(struct rmi_register_descriptor *rdesc);
+int rmi_register_desc_calc_reg_offset(
+			struct rmi_register_descriptor *rdesc, u16 reg);
+bool rmi_register_desc_has_subpacket(const struct rmi_register_desc_item *item,
+			u8 subpacket);
+
+bool rmi_is_physical_driver(struct device_driver *);
+int rmi_register_physical_driver(void);
+void rmi_unregister_physical_driver(void);
+
+char *rmi_f01_get_product_ID(struct rmi_function *fn);
+
+extern struct rmi_function_handler rmi_f01_handler;
+extern struct rmi_function_handler rmi_f11_handler;
+extern struct rmi_function_handler rmi_f12_handler;
+extern struct rmi_function_handler rmi_f30_handler;
+#endif

drivers/input/rmi4/rmi_f01.c

@@ -0,0 +1,624 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/kconfig.h>
+#include <linux/rmi.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/of.h>
+#include "rmi_driver.h"
+
+#define RMI_PRODUCT_ID_LENGTH    10
+#define RMI_PRODUCT_INFO_LENGTH   2
+
+#define RMI_DATE_CODE_LENGTH      3
+
+#define PRODUCT_ID_OFFSET 0x10
+#define PRODUCT_INFO_OFFSET 0x1E
+
+
+/* Force a firmware reset of the sensor */
+#define RMI_F01_CMD_DEVICE_RESET	1
+
+/* Various F01_RMI_QueryX bits */
+
+#define RMI_F01_QRY1_CUSTOM_MAP		BIT(0)
+#define RMI_F01_QRY1_NON_COMPLIANT	BIT(1)
+#define RMI_F01_QRY1_HAS_LTS		BIT(2)
+#define RMI_F01_QRY1_HAS_SENSOR_ID	BIT(3)
+#define RMI_F01_QRY1_HAS_CHARGER_INP	BIT(4)
+#define RMI_F01_QRY1_HAS_ADJ_DOZE	BIT(5)
+#define RMI_F01_QRY1_HAS_ADJ_DOZE_HOFF	BIT(6)
+#define RMI_F01_QRY1_HAS_QUERY42	BIT(7)
+
+#define RMI_F01_QRY5_YEAR_MASK		0x1f
+#define RMI_F01_QRY6_MONTH_MASK		0x0f
+#define RMI_F01_QRY7_DAY_MASK		0x1f
+
+#define RMI_F01_QRY2_PRODINFO_MASK	0x7f
+
+#define RMI_F01_BASIC_QUERY_LEN		21 /* From Query 00 through 20 */
+
+struct f01_basic_properties {
+	u8 manufacturer_id;
+	bool has_lts;
+	bool has_adjustable_doze;
+	bool has_adjustable_doze_holdoff;
+	char dom[11]; /* YYYY/MM/DD + '\0' */
+	u8 product_id[RMI_PRODUCT_ID_LENGTH + 1];
+	u16 productinfo;
+	u32 firmware_id;
+};
+
+/* F01 device status bits */
+
+/* Most recent device status event */
+#define RMI_F01_STATUS_CODE(status)		((status) & 0x0f)
+/* The device has lost its configuration for some reason. */
+#define RMI_F01_STATUS_UNCONFIGURED(status)	(!!((status) & 0x80))
+
+/* Control register bits */
+
+/*
+ * Sleep mode controls power management on the device and affects all
+ * functions of the device.
+ */
+#define RMI_F01_CTRL0_SLEEP_MODE_MASK	0x03
+
+#define RMI_SLEEP_MODE_NORMAL		0x00
+#define RMI_SLEEP_MODE_SENSOR_SLEEP	0x01
+#define RMI_SLEEP_MODE_RESERVED0	0x02
+#define RMI_SLEEP_MODE_RESERVED1	0x03
+
+/*
+ * This bit disables whatever sleep mode may be selected by the sleep_mode
+ * field and forces the device to run at full power without sleeping.
+ */
+#define RMI_F01_CRTL0_NOSLEEP_BIT	BIT(2)
+
+/*
+ * When this bit is set, the touch controller employs a noise-filtering
+ * algorithm designed for use with a connected battery charger.
+ */
+#define RMI_F01_CRTL0_CHARGER_BIT	BIT(5)
+
+/*
+ * Sets the report rate for the device. The effect of this setting is
+ * highly product dependent. Check the spec sheet for your particular
+ * touch sensor.
+ */
+#define RMI_F01_CRTL0_REPORTRATE_BIT	BIT(6)
+
+/*
+ * Written by the host as an indicator that the device has been
+ * successfully configured.
+ */
+#define RMI_F01_CRTL0_CONFIGURED_BIT	BIT(7)
+
+/**
+ * @ctrl0 - see the bit definitions above.
+ * @doze_interval - controls the interval between checks for finger presence
+ * when the touch sensor is in doze mode, in units of 10ms.
+ * @wakeup_threshold - controls the capacitance threshold at which the touch
+ * sensor will decide to wake up from that low power state.
+ * @doze_holdoff - controls how long the touch sensor waits after the last
+ * finger lifts before entering the doze state, in units of 100ms.
+ */
+struct f01_device_control {
+	u8 ctrl0;
+	u8 doze_interval;
+	u8 wakeup_threshold;
+	u8 doze_holdoff;
+};
+
+struct f01_data {
+	struct f01_basic_properties properties;
+	struct f01_device_control device_control;
+
+	u16 doze_interval_addr;
+	u16 wakeup_threshold_addr;
+	u16 doze_holdoff_addr;
+
+	bool suspended;
+	bool old_nosleep;
+
+	unsigned int num_of_irq_regs;
+};
+
+static int rmi_f01_read_properties(struct rmi_device *rmi_dev,
+				   u16 query_base_addr,
+				   struct f01_basic_properties *props)
+{
+	u8 queries[RMI_F01_BASIC_QUERY_LEN];
+	int ret;
+	int query_offset = query_base_addr;
+	bool has_ds4_queries = false;
+	bool has_query42 = false;
+	bool has_sensor_id = false;
+	bool has_package_id_query = false;
+	bool has_build_id_query = false;
+	u16 prod_info_addr;
+	u8 ds4_query_len;
+
+	ret = rmi_read_block(rmi_dev, query_offset,
+			       queries, RMI_F01_BASIC_QUERY_LEN);
+	if (ret) {
+		dev_err(&rmi_dev->dev,
+			"Failed to read device query registers: %d\n", ret);
+		return ret;
+	}
+
+	prod_info_addr = query_offset + 17;
+	query_offset += RMI_F01_BASIC_QUERY_LEN;
+
+	/* Now parse what we got */
+	props->manufacturer_id = queries[0];
+
+	props->has_lts = queries[1] & RMI_F01_QRY1_HAS_LTS;
+	props->has_adjustable_doze =
+			queries[1] & RMI_F01_QRY1_HAS_ADJ_DOZE;
+	props->has_adjustable_doze_holdoff =
+			queries[1] & RMI_F01_QRY1_HAS_ADJ_DOZE_HOFF;
+	has_query42 = queries[1] & RMI_F01_QRY1_HAS_QUERY42;
+	has_sensor_id = queries[1] & RMI_F01_QRY1_HAS_SENSOR_ID;
+
+	snprintf(props->dom, sizeof(props->dom), "20%02d/%02d/%02d",
+		 queries[5] & RMI_F01_QRY5_YEAR_MASK,
+		 queries[6] & RMI_F01_QRY6_MONTH_MASK,
+		 queries[7] & RMI_F01_QRY7_DAY_MASK);
+
+	memcpy(props->product_id, &queries[11],
+		RMI_PRODUCT_ID_LENGTH);
+	props->product_id[RMI_PRODUCT_ID_LENGTH] = '\0';
+
+	props->productinfo =
+			((queries[2] & RMI_F01_QRY2_PRODINFO_MASK) << 7) |
+			(queries[3] & RMI_F01_QRY2_PRODINFO_MASK);
+
+	if (has_sensor_id)
+		query_offset++;
+
+	if (has_query42) {
+		ret = rmi_read(rmi_dev, query_offset, queries);
+		if (ret) {
+			dev_err(&rmi_dev->dev,
+				"Failed to read query 42 register: %d\n", ret);
+			return ret;
+		}
+
+		has_ds4_queries = !!(queries[0] & BIT(0));
+		query_offset++;
+	}
+
+	if (has_ds4_queries) {
+		ret = rmi_read(rmi_dev, query_offset, &ds4_query_len);
+		if (ret) {
+			dev_err(&rmi_dev->dev,
+				"Failed to read DS4 queries length: %d\n", ret);
+			return ret;
+		}
+		query_offset++;
+
+		if (ds4_query_len > 0) {
+			ret = rmi_read(rmi_dev, query_offset, queries);
+			if (ret) {
+				dev_err(&rmi_dev->dev,
+					"Failed to read DS4 queries: %d\n",
+					ret);
+				return ret;
+			}
+
+			has_package_id_query = !!(queries[0] & BIT(0));
+			has_build_id_query = !!(queries[0] & BIT(1));
+		}
+
+		if (has_package_id_query)
+			prod_info_addr++;
+
+		if (has_build_id_query) {
+			ret = rmi_read_block(rmi_dev, prod_info_addr, queries,
+					    3);
+			if (ret) {
+				dev_err(&rmi_dev->dev,
+					"Failed to read product info: %d\n",
+					ret);
+				return ret;
+			}
+
+			props->firmware_id = queries[1] << 8 | queries[0];
+			props->firmware_id += queries[2] * 65536;
+		}
+	}
+
+	return 0;
+}
+
+char *rmi_f01_get_product_ID(struct rmi_function *fn)
+{
+	struct f01_data *f01 = dev_get_drvdata(&fn->dev);
+
+	return f01->properties.product_id;
+}
+
+#ifdef CONFIG_OF
+static int rmi_f01_of_probe(struct device *dev,
+				struct rmi_device_platform_data *pdata)
+{
+	int retval;
+	u32 val;
+
+	retval = rmi_of_property_read_u32(dev,
+			(u32 *)&pdata->power_management.nosleep,
+			"syna,nosleep-mode", 1);
+	if (retval)
+		return retval;
+
+	retval = rmi_of_property_read_u32(dev, &val,
+			"syna,wakeup-threshold", 1);
+	if (retval)
+		return retval;
+
+	pdata->power_management.wakeup_threshold = val;
+
+	retval = rmi_of_property_read_u32(dev, &val,
+			"syna,doze-holdoff-ms", 1);
+	if (retval)
+		return retval;
+
+	pdata->power_management.doze_holdoff = val * 100;
+
+	retval = rmi_of_property_read_u32(dev, &val,
+			"syna,doze-interval-ms", 1);
+	if (retval)
+		return retval;
+
+	pdata->power_management.doze_interval = val / 10;
+
+	return 0;
+}
+#else
+static inline int rmi_f01_of_probe(struct device *dev,
+					struct rmi_device_platform_data *pdata)
+{
+	return -ENODEV;
+}
+#endif
+
+static int rmi_f01_probe(struct rmi_function *fn)
+{
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	struct rmi_driver_data *driver_data = dev_get_drvdata(&rmi_dev->dev);
+	struct rmi_device_platform_data *pdata = rmi_get_platform_data(rmi_dev);
+	struct f01_data *f01;
+	int error;
+	u16 ctrl_base_addr = fn->fd.control_base_addr;
+	u8 device_status;
+	u8 temp;
+
+	if (fn->dev.of_node) {
+		error = rmi_f01_of_probe(&fn->dev, pdata);
+		if (error)
+			return error;
+	}
+
+	f01 = devm_kzalloc(&fn->dev, sizeof(struct f01_data), GFP_KERNEL);
+	if (!f01)
+		return -ENOMEM;
+
+	f01->num_of_irq_regs = driver_data->num_of_irq_regs;
+
+	/*
+	 * Set the configured bit and (optionally) other important stuff
+	 * in the device control register.
+	 */
+
+	error = rmi_read(rmi_dev, fn->fd.control_base_addr,
+			 &f01->device_control.ctrl0);
+	if (error) {
+		dev_err(&fn->dev, "Failed to read F01 control: %d\n", error);
+		return error;
+	}
+
+	switch (pdata->power_management.nosleep) {
+	case RMI_F01_NOSLEEP_DEFAULT:
+		break;
+	case RMI_F01_NOSLEEP_OFF:
+		f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
+		break;
+	case RMI_F01_NOSLEEP_ON:
+		f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+		break;
+	}
+
+	/*
+	 * Sleep mode might be set as a hangover from a system crash or
+	 * reboot without power cycle.  If so, clear it so the sensor
+	 * is certain to function.
+	 */
+	if ((f01->device_control.ctrl0 & RMI_F01_CTRL0_SLEEP_MODE_MASK) !=
+			RMI_SLEEP_MODE_NORMAL) {
+		dev_warn(&fn->dev,
+			 "WARNING: Non-zero sleep mode found. Clearing...\n");
+		f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
+	}
+
+	f01->device_control.ctrl0 |= RMI_F01_CRTL0_CONFIGURED_BIT;
+
+	error = rmi_write(rmi_dev, fn->fd.control_base_addr,
+			  f01->device_control.ctrl0);
+	if (error) {
+		dev_err(&fn->dev, "Failed to write F01 control: %d\n", error);
+		return error;
+	}
+
+	/* Dummy read in order to clear irqs */
+	error = rmi_read(rmi_dev, fn->fd.data_base_addr + 1, &temp);
+	if (error < 0) {
+		dev_err(&fn->dev, "Failed to read Interrupt Status.\n");
+		return error;
+	}
+
+	error = rmi_f01_read_properties(rmi_dev, fn->fd.query_base_addr,
+					&f01->properties);
+	if (error < 0) {
+		dev_err(&fn->dev, "Failed to read F01 properties.\n");
+		return error;
+	}
+
+	dev_info(&fn->dev, "found RMI device, manufacturer: %s, product: %s, fw id: %d\n",
+		 f01->properties.manufacturer_id == 1 ? "Synaptics" : "unknown",
+		 f01->properties.product_id, f01->properties.firmware_id);
+
+	/* Advance to interrupt control registers, then skip over them. */
+	ctrl_base_addr++;
+	ctrl_base_addr += f01->num_of_irq_regs;
+
+	/* read control register */
+	if (f01->properties.has_adjustable_doze) {
+		f01->doze_interval_addr = ctrl_base_addr;
+		ctrl_base_addr++;
+
+		if (pdata->power_management.doze_interval) {
+			f01->device_control.doze_interval =
+				pdata->power_management.doze_interval;
+			error = rmi_write(rmi_dev, f01->doze_interval_addr,
+					  f01->device_control.doze_interval);
+			if (error) {
+				dev_err(&fn->dev,
+					"Failed to configure F01 doze interval register: %d\n",
+					error);
+				return error;
+			}
+		} else {
+			error = rmi_read(rmi_dev, f01->doze_interval_addr,
+					 &f01->device_control.doze_interval);
+			if (error) {
+				dev_err(&fn->dev,
+					"Failed to read F01 doze interval register: %d\n",
+					error);
+				return error;
+			}
+		}
+
+		f01->wakeup_threshold_addr = ctrl_base_addr;
+		ctrl_base_addr++;
+
+		if (pdata->power_management.wakeup_threshold) {
+			f01->device_control.wakeup_threshold =
+				pdata->power_management.wakeup_threshold;
+			error = rmi_write(rmi_dev, f01->wakeup_threshold_addr,
+					  f01->device_control.wakeup_threshold);
+			if (error) {
+				dev_err(&fn->dev,
+					"Failed to configure F01 wakeup threshold register: %d\n",
+					error);
+				return error;
+			}
+		} else {
+			error = rmi_read(rmi_dev, f01->wakeup_threshold_addr,
+					 &f01->device_control.wakeup_threshold);
+			if (error < 0) {
+				dev_err(&fn->dev,
+					"Failed to read F01 wakeup threshold register: %d\n",
+					error);
+				return error;
+			}
+		}
+	}
+
+	if (f01->properties.has_lts)
+		ctrl_base_addr++;
+
+	if (f01->properties.has_adjustable_doze_holdoff) {
+		f01->doze_holdoff_addr = ctrl_base_addr;
+		ctrl_base_addr++;
+
+		if (pdata->power_management.doze_holdoff) {
+			f01->device_control.doze_holdoff =
+				pdata->power_management.doze_holdoff;
+			error = rmi_write(rmi_dev, f01->doze_holdoff_addr,
+					  f01->device_control.doze_holdoff);
+			if (error) {
+				dev_err(&fn->dev,
+					"Failed to configure F01 doze holdoff register: %d\n",
+					error);
+				return error;
+			}
+		} else {
+			error = rmi_read(rmi_dev, f01->doze_holdoff_addr,
+					 &f01->device_control.doze_holdoff);
+			if (error) {
+				dev_err(&fn->dev,
+					"Failed to read F01 doze holdoff register: %d\n",
+					error);
+				return error;
+			}
+		}
+	}
+
+	error = rmi_read(rmi_dev, fn->fd.data_base_addr, &device_status);
+	if (error < 0) {
+		dev_err(&fn->dev,
+			"Failed to read device status: %d\n", error);
+		return error;
+	}
+
+	if (RMI_F01_STATUS_UNCONFIGURED(device_status)) {
+		dev_err(&fn->dev,
+			"Device was reset during configuration process, status: %#02x!\n",
+			RMI_F01_STATUS_CODE(device_status));
+		return -EINVAL;
+	}
+
+	dev_set_drvdata(&fn->dev, f01);
+
+	return 0;
+}
+
+static int rmi_f01_config(struct rmi_function *fn)
+{
+	struct f01_data *f01 = dev_get_drvdata(&fn->dev);
+	int error;
+
+	error = rmi_write(fn->rmi_dev, fn->fd.control_base_addr,
+			  f01->device_control.ctrl0);
+	if (error) {
+		dev_err(&fn->dev,
+			"Failed to write device_control register: %d\n", error);
+		return error;
+	}
+
+	if (f01->properties.has_adjustable_doze) {
+		error = rmi_write(fn->rmi_dev, f01->doze_interval_addr,
+				  f01->device_control.doze_interval);
+		if (error) {
+			dev_err(&fn->dev,
+				"Failed to write doze interval: %d\n", error);
+			return error;
+		}
+
+		error = rmi_write_block(fn->rmi_dev,
+					 f01->wakeup_threshold_addr,
+					 &f01->device_control.wakeup_threshold,
+					 sizeof(u8));
+		if (error) {
+			dev_err(&fn->dev,
+				"Failed to write wakeup threshold: %d\n",
+				error);
+			return error;
+		}
+	}
+
+	if (f01->properties.has_adjustable_doze_holdoff) {
+		error = rmi_write(fn->rmi_dev, f01->doze_holdoff_addr,
+				  f01->device_control.doze_holdoff);
+		if (error) {
+			dev_err(&fn->dev,
+				"Failed to write doze holdoff: %d\n", error);
+			return error;
+		}
+	}
+
+	return 0;
+}
+
+static int rmi_f01_suspend(struct rmi_function *fn)
+{
+	struct f01_data *f01 = dev_get_drvdata(&fn->dev);
+	int error;
+
+	f01->old_nosleep =
+		f01->device_control.ctrl0 & RMI_F01_CRTL0_NOSLEEP_BIT;
+	f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
+
+	f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
+	if (device_may_wakeup(fn->rmi_dev->xport->dev))
+		f01->device_control.ctrl0 |= RMI_SLEEP_MODE_RESERVED1;
+	else
+		f01->device_control.ctrl0 |= RMI_SLEEP_MODE_SENSOR_SLEEP;
+
+	error = rmi_write(fn->rmi_dev, fn->fd.control_base_addr,
+			  f01->device_control.ctrl0);
+	if (error) {
+		dev_err(&fn->dev, "Failed to write sleep mode: %d.\n", error);
+		if (f01->old_nosleep)
+			f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+		f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
+		f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;
+		return error;
+	}
+
+	return 0;
+}
+
+static int rmi_f01_resume(struct rmi_function *fn)
+{
+	struct f01_data *f01 = dev_get_drvdata(&fn->dev);
+	int error;
+
+	if (f01->old_nosleep)
+		f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+
+	f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
+	f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;
+
+	error = rmi_write(fn->rmi_dev, fn->fd.control_base_addr,
+			  f01->device_control.ctrl0);
+	if (error) {
+		dev_err(&fn->dev,
+			"Failed to restore normal operation: %d.\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int rmi_f01_attention(struct rmi_function *fn,
+			     unsigned long *irq_bits)
+{
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	int error;
+	u8 device_status;
+
+	error = rmi_read(rmi_dev, fn->fd.data_base_addr, &device_status);
+	if (error) {
+		dev_err(&fn->dev,
+			"Failed to read device status: %d.\n", error);
+		return error;
+	}
+
+	if (RMI_F01_STATUS_UNCONFIGURED(device_status)) {
+		dev_warn(&fn->dev, "Device reset detected.\n");
+		error = rmi_dev->driver->reset_handler(rmi_dev);
+		if (error) {
+			dev_err(&fn->dev, "Device reset failed: %d\n", error);
+			return error;
+		}
+	}
+
+	return 0;
+}
+
+struct rmi_function_handler rmi_f01_handler = {
+	.driver = {
+		.name	= "rmi4_f01",
+		/*
+		 * Do not allow user unbinding F01 as it is critical
+		 * function.
+		 */
+		.suppress_bind_attrs = true,
+	},
+	.func		= 0x01,
+	.probe		= rmi_f01_probe,
+	.config		= rmi_f01_config,
+	.attention	= rmi_f01_attention,
+	.suspend	= rmi_f01_suspend,
+	.resume		= rmi_f01_resume,
+};

drivers/input/rmi4/rmi_f11.c

@@ -0,0 +1,1317 @@
+/*
+ * Copyright (c) 2011-2015 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/kconfig.h>
+#include <linux/rmi.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include "rmi_driver.h"
+#include "rmi_2d_sensor.h"
+
+#define F11_MAX_NUM_OF_FINGERS		10
+#define F11_MAX_NUM_OF_TOUCH_SHAPES	16
+
+#define FINGER_STATE_MASK	0x03
+
+#define F11_CTRL_SENSOR_MAX_X_POS_OFFSET	6
+#define F11_CTRL_SENSOR_MAX_Y_POS_OFFSET	8
+
+#define DEFAULT_XY_MAX 9999
+#define DEFAULT_MAX_ABS_MT_PRESSURE 255
+#define DEFAULT_MAX_ABS_MT_TOUCH 15
+#define DEFAULT_MAX_ABS_MT_ORIENTATION 1
+#define DEFAULT_MIN_ABS_MT_TRACKING_ID 1
+#define DEFAULT_MAX_ABS_MT_TRACKING_ID 10
+
+/** A note about RMI4 F11 register structure.
+ *
+ * The properties for
+ * a given sensor are described by its query registers.  The number of query
+ * registers and the layout of their contents are described by the F11 device
+ * queries as well as the sensor query information.
+ *
+ * Similarly, each sensor has control registers that govern its behavior.  The
+ * size and layout of the control registers for a given sensor can be determined
+ * by parsing that sensors query registers.
+ *
+ * And in a likewise fashion, each sensor has data registers where it reports
+ * its touch data and other interesting stuff.  The size and layout of a
+ * sensors data registers must be determined by parsing its query registers.
+ *
+ * The short story is that we need to read and parse a lot of query
+ * registers in order to determine the attributes of a sensor. Then
+ * we need to use that data to compute the size of the control and data
+ * registers for sensor.
+ *
+ * The end result is that we have a number of structs that aren't used to
+ * directly generate the input events, but their size, location and contents
+ * are critical to determining where the data we are interested in lives.
+ *
+ * At this time, the driver does not yet comprehend all possible F11
+ * configuration options, but it should be sufficient to cover 99% of RMI4 F11
+ * devices currently in the field.
+ */
+
+/* maximum ABS_MT_POSITION displacement (in mm) */
+#define DMAX 10
+
+/**
+ * @rezero - writing this to the F11 command register will cause the sensor to
+ * calibrate to the current capacitive state.
+ */
+#define RMI_F11_REZERO  0x01
+
+#define RMI_F11_HAS_QUERY9              (1 << 3)
+#define RMI_F11_HAS_QUERY11             (1 << 4)
+#define RMI_F11_HAS_QUERY12             (1 << 5)
+#define RMI_F11_HAS_QUERY27             (1 << 6)
+#define RMI_F11_HAS_QUERY28             (1 << 7)
+
+/** Defs for Query 1 */
+
+#define RMI_F11_NR_FINGERS_MASK 0x07
+#define RMI_F11_HAS_REL                 (1 << 3)
+#define RMI_F11_HAS_ABS                 (1 << 4)
+#define RMI_F11_HAS_GESTURES            (1 << 5)
+#define RMI_F11_HAS_SENSITIVITY_ADJ     (1 << 6)
+#define RMI_F11_CONFIGURABLE            (1 << 7)
+
+/** Defs for Query 2, 3, and 4. */
+#define RMI_F11_NR_ELECTRODES_MASK      0x7F
+
+/** Defs for Query 5 */
+
+#define RMI_F11_ABS_DATA_SIZE_MASK      0x03
+#define RMI_F11_HAS_ANCHORED_FINGER     (1 << 2)
+#define RMI_F11_HAS_ADJ_HYST            (1 << 3)
+#define RMI_F11_HAS_DRIBBLE             (1 << 4)
+#define RMI_F11_HAS_BENDING_CORRECTION  (1 << 5)
+#define RMI_F11_HAS_LARGE_OBJECT_SUPPRESSION    (1 << 6)
+#define RMI_F11_HAS_JITTER_FILTER       (1 << 7)
+
+/** Defs for Query 7 */
+#define RMI_F11_HAS_SINGLE_TAP                  (1 << 0)
+#define RMI_F11_HAS_TAP_AND_HOLD                (1 << 1)
+#define RMI_F11_HAS_DOUBLE_TAP                  (1 << 2)
+#define RMI_F11_HAS_EARLY_TAP                   (1 << 3)
+#define RMI_F11_HAS_FLICK                       (1 << 4)
+#define RMI_F11_HAS_PRESS                       (1 << 5)
+#define RMI_F11_HAS_PINCH                       (1 << 6)
+#define RMI_F11_HAS_CHIRAL                      (1 << 7)
+
+/** Defs for Query 8 */
+#define RMI_F11_HAS_PALM_DET                    (1 << 0)
+#define RMI_F11_HAS_ROTATE                      (1 << 1)
+#define RMI_F11_HAS_TOUCH_SHAPES                (1 << 2)
+#define RMI_F11_HAS_SCROLL_ZONES                (1 << 3)
+#define RMI_F11_HAS_INDIVIDUAL_SCROLL_ZONES     (1 << 4)
+#define RMI_F11_HAS_MF_SCROLL                   (1 << 5)
+#define RMI_F11_HAS_MF_EDGE_MOTION              (1 << 6)
+#define RMI_F11_HAS_MF_SCROLL_INERTIA           (1 << 7)
+
+/** Defs for Query 9. */
+#define RMI_F11_HAS_PEN                         (1 << 0)
+#define RMI_F11_HAS_PROXIMITY                   (1 << 1)
+#define RMI_F11_HAS_PALM_DET_SENSITIVITY        (1 << 2)
+#define RMI_F11_HAS_SUPPRESS_ON_PALM_DETECT     (1 << 3)
+#define RMI_F11_HAS_TWO_PEN_THRESHOLDS          (1 << 4)
+#define RMI_F11_HAS_CONTACT_GEOMETRY            (1 << 5)
+#define RMI_F11_HAS_PEN_HOVER_DISCRIMINATION    (1 << 6)
+#define RMI_F11_HAS_PEN_FILTERS                 (1 << 7)
+
+/** Defs for Query 10. */
+#define RMI_F11_NR_TOUCH_SHAPES_MASK            0x1F
+
+/** Defs for Query 11 */
+
+#define RMI_F11_HAS_Z_TUNING                    (1 << 0)
+#define RMI_F11_HAS_ALGORITHM_SELECTION         (1 << 1)
+#define RMI_F11_HAS_W_TUNING                    (1 << 2)
+#define RMI_F11_HAS_PITCH_INFO                  (1 << 3)
+#define RMI_F11_HAS_FINGER_SIZE                 (1 << 4)
+#define RMI_F11_HAS_SEGMENTATION_AGGRESSIVENESS (1 << 5)
+#define RMI_F11_HAS_XY_CLIP                     (1 << 6)
+#define RMI_F11_HAS_DRUMMING_FILTER             (1 << 7)
+
+/** Defs for Query 12. */
+
+#define RMI_F11_HAS_GAPLESS_FINGER              (1 << 0)
+#define RMI_F11_HAS_GAPLESS_FINGER_TUNING       (1 << 1)
+#define RMI_F11_HAS_8BIT_W                      (1 << 2)
+#define RMI_F11_HAS_ADJUSTABLE_MAPPING          (1 << 3)
+#define RMI_F11_HAS_INFO2                       (1 << 4)
+#define RMI_F11_HAS_PHYSICAL_PROPS              (1 << 5)
+#define RMI_F11_HAS_FINGER_LIMIT                (1 << 6)
+#define RMI_F11_HAS_LINEAR_COEFF                (1 << 7)
+
+/** Defs for Query 13. */
+
+#define RMI_F11_JITTER_WINDOW_MASK              0x1F
+#define RMI_F11_JITTER_FILTER_MASK              0x60
+#define RMI_F11_JITTER_FILTER_SHIFT             5
+
+/** Defs for Query 14. */
+#define RMI_F11_LIGHT_CONTROL_MASK              0x03
+#define RMI_F11_IS_CLEAR                        (1 << 2)
+#define RMI_F11_CLICKPAD_PROPS_MASK             0x18
+#define RMI_F11_CLICKPAD_PROPS_SHIFT            3
+#define RMI_F11_MOUSE_BUTTONS_MASK              0x60
+#define RMI_F11_MOUSE_BUTTONS_SHIFT             5
+#define RMI_F11_HAS_ADVANCED_GESTURES           (1 << 7)
+
+#define RMI_F11_QUERY_SIZE                      4
+#define RMI_F11_QUERY_GESTURE_SIZE              2
+
+#define F11_LIGHT_CTL_NONE 0x00
+#define F11_LUXPAD	   0x01
+#define F11_DUAL_MODE      0x02
+
+#define F11_NOT_CLICKPAD     0x00
+#define F11_HINGED_CLICKPAD  0x01
+#define F11_UNIFORM_CLICKPAD 0x02
+
+/**
+ * Query registers 1 through 4 are always present.
+ *
+ * @nr_fingers - describes the maximum number of fingers the 2-D sensor
+ * supports.
+ * @has_rel - the sensor supports relative motion reporting.
+ * @has_abs - the sensor supports absolute poition reporting.
+ * @has_gestures - the sensor supports gesture reporting.
+ * @has_sensitivity_adjust - the sensor supports a global sensitivity
+ * adjustment.
+ * @configurable - the sensor supports various configuration options.
+ * @num_of_x_electrodes -  the maximum number of electrodes the 2-D sensor
+ * supports on the X axis.
+ * @num_of_y_electrodes -  the maximum number of electrodes the 2-D sensor
+ * supports on the Y axis.
+ * @max_electrodes - the total number of X and Y electrodes that may be
+ * configured.
+ *
+ * Query 5 is present if the has_abs bit is set.
+ *
+ * @abs_data_size - describes the format of data reported by the absolute
+ * data source.  Only one format (the kind used here) is supported at this
+ * time.
+ * @has_anchored_finger - then the sensor supports the high-precision second
+ * finger tracking provided by the manual tracking and motion sensitivity
+ * options.
+ * @has_adjust_hyst - the difference between the finger release threshold and
+ * the touch threshold.
+ * @has_dribble - the sensor supports the generation of dribble interrupts,
+ * which may be enabled or disabled with the dribble control bit.
+ * @has_bending_correction - Bending related data registers 28 and 36, and
+ * control register 52..57 are present.
+ * @has_large_object_suppression - control register 58 and data register 28
+ * exist.
+ * @has_jitter_filter - query 13 and control 73..76 exist.
+ *
+ * Gesture information queries 7 and 8 are present if has_gestures bit is set.
+ *
+ * @has_single_tap - a basic single-tap gesture is supported.
+ * @has_tap_n_hold - tap-and-hold gesture is supported.
+ * @has_double_tap - double-tap gesture is supported.
+ * @has_early_tap - early tap is supported and reported as soon as the finger
+ * lifts for any tap event that could be interpreted as either a single tap
+ * or as the first tap of a double-tap or tap-and-hold gesture.
+ * @has_flick - flick detection is supported.
+ * @has_press - press gesture reporting is supported.
+ * @has_pinch - pinch gesture detection is supported.
+ * @has_palm_det - the 2-D sensor notifies the host whenever a large conductive
+ * object such as a palm or a cheek touches the 2-D sensor.
+ * @has_rotate - rotation gesture detection is supported.
+ * @has_touch_shapes - TouchShapes are supported.  A TouchShape is a fixed
+ * rectangular area on the sensor that behaves like a capacitive button.
+ * @has_scroll_zones - scrolling areas near the sensor edges are supported.
+ * @has_individual_scroll_zones - if 1, then 4 scroll zones are supported;
+ * if 0, then only two are supported.
+ * @has_mf_scroll - the multifinger_scrolling bit will be set when
+ * more than one finger is involved in a scrolling action.
+ *
+ * Convenience for checking bytes in the gesture info registers.  This is done
+ * often enough that we put it here to declutter the conditionals
+ *
+ * @query7_nonzero - true if none of the query 7 bits are set
+ * @query8_nonzero - true if none of the query 8 bits are set
+ *
+ * Query 9 is present if the has_query9 is set.
+ *
+ * @has_pen - detection of a stylus is supported and registers F11_2D_Ctrl20
+ * and F11_2D_Ctrl21 exist.
+ * @has_proximity - detection of fingers near the sensor is supported and
+ * registers F11_2D_Ctrl22 through F11_2D_Ctrl26 exist.
+ * @has_palm_det_sensitivity -  the sensor supports the palm detect sensitivity
+ * feature and register F11_2D_Ctrl27 exists.
+ * @has_two_pen_thresholds - is has_pen is also set, then F11_2D_Ctrl35 exists.
+ * @has_contact_geometry - the sensor supports the use of contact geometry to
+ * map absolute X and Y target positions and registers F11_2D_Data18
+ * through F11_2D_Data27 exist.
+ *
+ * Touch shape info (query 10) is present if has_touch_shapes is set.
+ *
+ * @nr_touch_shapes - the total number of touch shapes supported.
+ *
+ * Query 11 is present if the has_query11 bit is set in query 0.
+ *
+ * @has_z_tuning - if set, the sensor supports Z tuning and registers
+ * F11_2D_Ctrl29 through F11_2D_Ctrl33 exist.
+ * @has_algorithm_selection - controls choice of noise suppression algorithm
+ * @has_w_tuning - the sensor supports Wx and Wy scaling and registers
+ * F11_2D_Ctrl36 through F11_2D_Ctrl39 exist.
+ * @has_pitch_info - the X and Y pitches of the sensor electrodes can be
+ * configured and registers F11_2D_Ctrl40 and F11_2D_Ctrl41 exist.
+ * @has_finger_size -  the default finger width settings for the
+ * sensor can be configured and registers F11_2D_Ctrl42 through F11_2D_Ctrl44
+ * exist.
+ * @has_segmentation_aggressiveness - the sensor’s ability to distinguish
+ * multiple objects close together can be configured and register F11_2D_Ctrl45
+ * exists.
+ * @has_XY_clip -  the inactive outside borders of the sensor can be
+ * configured and registers F11_2D_Ctrl46 through F11_2D_Ctrl49 exist.
+ * @has_drumming_filter - the sensor can be configured to distinguish
+ * between a fast flick and a quick drumming movement and registers
+ * F11_2D_Ctrl50 and F11_2D_Ctrl51 exist.
+ *
+ * Query 12 is present if hasQuery12 bit is set.
+ *
+ * @has_gapless_finger - control registers relating to gapless finger are
+ * present.
+ * @has_gapless_finger_tuning - additional control and data registers relating
+ * to gapless finger are present.
+ * @has_8bit_w - larger W value reporting is supported.
+ * @has_adjustable_mapping - TBD
+ * @has_info2 - the general info query14 is present
+ * @has_physical_props - additional queries describing the physical properties
+ * of the sensor are present.
+ * @has_finger_limit - indicates that F11 Ctrl 80 exists.
+ * @has_linear_coeff - indicates that F11 Ctrl 81 exists.
+ *
+ * Query 13 is present if Query 5's has_jitter_filter bit is set.
+ * @jitter_window_size - used by Design Studio 4.
+ * @jitter_filter_type - used by Design Studio 4.
+ *
+ * Query 14 is present if query 12's has_general_info2 flag is set.
+ *
+ * @light_control - Indicates what light/led control features are present, if
+ * any.
+ * @is_clear - if set, this is a clear sensor (indicating direct pointing
+ * application), otherwise it's opaque (indicating indirect pointing).
+ * @clickpad_props - specifies if this is a clickpad, and if so what sort of
+ * mechanism it uses
+ * @mouse_buttons - specifies the number of mouse buttons present (if any).
+ * @has_advanced_gestures - advanced driver gestures are supported.
+ */
+struct f11_2d_sensor_queries {
+	/* query1 */
+	u8 nr_fingers;
+	bool has_rel;
+	bool has_abs;
+	bool has_gestures;
+	bool has_sensitivity_adjust;
+	bool configurable;
+
+	/* query2 */
+	u8 nr_x_electrodes;
+
+	/* query3 */
+	u8 nr_y_electrodes;
+
+	/* query4 */
+	u8 max_electrodes;
+
+	/* query5 */
+	u8 abs_data_size;
+	bool has_anchored_finger;
+	bool has_adj_hyst;
+	bool has_dribble;
+	bool has_bending_correction;
+	bool has_large_object_suppression;
+	bool has_jitter_filter;
+
+	u8 f11_2d_query6;
+
+	/* query 7 */
+	bool has_single_tap;
+	bool has_tap_n_hold;
+	bool has_double_tap;
+	bool has_early_tap;
+	bool has_flick;
+	bool has_press;
+	bool has_pinch;
+	bool has_chiral;
+
+	bool query7_nonzero;
+
+	/* query 8 */
+	bool has_palm_det;
+	bool has_rotate;
+	bool has_touch_shapes;
+	bool has_scroll_zones;
+	bool has_individual_scroll_zones;
+	bool has_mf_scroll;
+	bool has_mf_edge_motion;
+	bool has_mf_scroll_inertia;
+
+	bool query8_nonzero;
+
+	/* Query 9 */
+	bool has_pen;
+	bool has_proximity;
+	bool has_palm_det_sensitivity;
+	bool has_suppress_on_palm_detect;
+	bool has_two_pen_thresholds;
+	bool has_contact_geometry;
+	bool has_pen_hover_discrimination;
+	bool has_pen_filters;
+
+	/* Query 10 */
+	u8 nr_touch_shapes;
+
+	/* Query 11. */
+	bool has_z_tuning;
+	bool has_algorithm_selection;
+	bool has_w_tuning;
+	bool has_pitch_info;
+	bool has_finger_size;
+	bool has_segmentation_aggressiveness;
+	bool has_XY_clip;
+	bool has_drumming_filter;
+
+	/* Query 12 */
+	bool has_gapless_finger;
+	bool has_gapless_finger_tuning;
+	bool has_8bit_w;
+	bool has_adjustable_mapping;
+	bool has_info2;
+	bool has_physical_props;
+	bool has_finger_limit;
+	bool has_linear_coeff_2;
+
+	/* Query 13 */
+	u8 jitter_window_size;
+	u8 jitter_filter_type;
+
+	/* Query 14 */
+	u8 light_control;
+	bool is_clear;
+	u8 clickpad_props;
+	u8 mouse_buttons;
+	bool has_advanced_gestures;
+
+	/* Query 15 - 18 */
+	u16 x_sensor_size_mm;
+	u16 y_sensor_size_mm;
+};
+
+/* Defs for Ctrl0. */
+#define RMI_F11_REPORT_MODE_MASK        0x07
+#define RMI_F11_ABS_POS_FILT            (1 << 3)
+#define RMI_F11_REL_POS_FILT            (1 << 4)
+#define RMI_F11_REL_BALLISTICS          (1 << 5)
+#define RMI_F11_DRIBBLE                 (1 << 6)
+#define RMI_F11_REPORT_BEYOND_CLIP      (1 << 7)
+
+/* Defs for Ctrl1. */
+#define RMI_F11_PALM_DETECT_THRESH_MASK 0x0F
+#define RMI_F11_MOTION_SENSITIVITY_MASK 0x30
+#define RMI_F11_MANUAL_TRACKING         (1 << 6)
+#define RMI_F11_MANUAL_TRACKED_FINGER   (1 << 7)
+
+#define RMI_F11_DELTA_X_THRESHOLD       2
+#define RMI_F11_DELTA_Y_THRESHOLD       3
+
+#define RMI_F11_CTRL_REG_COUNT          12
+
+struct f11_2d_ctrl {
+	u8              ctrl0_11[RMI_F11_CTRL_REG_COUNT];
+	u16             ctrl0_11_address;
+};
+
+#define RMI_F11_ABS_BYTES 5
+#define RMI_F11_REL_BYTES 2
+
+/* Defs for Data 8 */
+
+#define RMI_F11_SINGLE_TAP              (1 << 0)
+#define RMI_F11_TAP_AND_HOLD            (1 << 1)
+#define RMI_F11_DOUBLE_TAP              (1 << 2)
+#define RMI_F11_EARLY_TAP               (1 << 3)
+#define RMI_F11_FLICK                   (1 << 4)
+#define RMI_F11_PRESS                   (1 << 5)
+#define RMI_F11_PINCH                   (1 << 6)
+
+/* Defs for Data 9 */
+
+#define RMI_F11_PALM_DETECT                     (1 << 0)
+#define RMI_F11_ROTATE                          (1 << 1)
+#define RMI_F11_SHAPE                           (1 << 2)
+#define RMI_F11_SCROLLZONE                      (1 << 3)
+#define RMI_F11_GESTURE_FINGER_COUNT_MASK       0x70
+
+/** Handy pointers into our data buffer.
+ *
+ * @f_state - start of finger state registers.
+ * @abs_pos - start of absolute position registers (if present).
+ * @rel_pos - start of relative data registers (if present).
+ * @gest_1  - gesture flags (if present).
+ * @gest_2  - gesture flags & finger count (if present).
+ * @pinch   - pinch motion register (if present).
+ * @flick   - flick distance X & Y, flick time (if present).
+ * @rotate  - rotate motion and finger separation.
+ * @multi_scroll - chiral deltas for X and Y (if present).
+ * @scroll_zones - scroll deltas for 4 regions (if present).
+ */
+struct f11_2d_data {
+	u8	*f_state;
+	u8	*abs_pos;
+	s8	*rel_pos;
+	u8	*gest_1;
+	u8	*gest_2;
+	s8	*pinch;
+	u8	*flick;
+	u8	*rotate;
+	u8	*shapes;
+	s8	*multi_scroll;
+	s8	*scroll_zones;
+};
+
+/** Data pertaining to F11 in general.  For per-sensor data, see struct
+ * f11_2d_sensor.
+ *
+ * @dev_query - F11 device specific query registers.
+ * @dev_controls - F11 device specific control registers.
+ * @dev_controls_mutex - lock for the control registers.
+ * @rezero_wait_ms - if nonzero, upon resume we will wait this many
+ * milliseconds before rezeroing the sensor(s).  This is useful in systems with
+ * poor electrical behavior on resume, where the initial calibration of the
+ * sensor(s) coming out of sleep state may be bogus.
+ * @sensors - per sensor data structures.
+ */
+struct f11_data {
+	bool has_query9;
+	bool has_query11;
+	bool has_query12;
+	bool has_query27;
+	bool has_query28;
+	bool has_acm;
+	struct f11_2d_ctrl dev_controls;
+	struct mutex dev_controls_mutex;
+	u16 rezero_wait_ms;
+	struct rmi_2d_sensor sensor;
+	struct f11_2d_sensor_queries sens_query;
+	struct f11_2d_data data;
+	struct rmi_2d_sensor_platform_data sensor_pdata;
+	unsigned long *abs_mask;
+	unsigned long *rel_mask;
+	unsigned long *result_bits;
+};
+
+enum f11_finger_state {
+	F11_NO_FINGER	= 0x00,
+	F11_PRESENT	= 0x01,
+	F11_INACCURATE	= 0x02,
+	F11_RESERVED	= 0x03
+};
+
+static void rmi_f11_rel_pos_report(struct f11_data *f11, u8 n_finger)
+{
+	struct rmi_2d_sensor *sensor = &f11->sensor;
+	struct f11_2d_data *data = &f11->data;
+	s8 x, y;
+
+	x = data->rel_pos[n_finger * 2];
+	y = data->rel_pos[n_finger * 2 + 1];
+
+	rmi_2d_sensor_rel_report(sensor, x, y);
+}
+
+static void rmi_f11_abs_pos_process(struct f11_data *f11,
+				   struct rmi_2d_sensor *sensor,
+				   struct rmi_2d_sensor_abs_object *obj,
+				   enum f11_finger_state finger_state,
+				   u8 n_finger)
+{
+	struct f11_2d_data *data = &f11->data;
+	u8 *pos_data = &data->abs_pos[n_finger * RMI_F11_ABS_BYTES];
+	int tool_type = MT_TOOL_FINGER;
+
+	switch (finger_state) {
+	case F11_PRESENT:
+		obj->type = RMI_2D_OBJECT_FINGER;
+		break;
+	default:
+		obj->type = RMI_2D_OBJECT_NONE;
+	}
+
+	obj->mt_tool = tool_type;
+	obj->x = (pos_data[0] << 4) | (pos_data[2] & 0x0F);
+	obj->y = (pos_data[1] << 4) | (pos_data[2] >> 4);
+	obj->z = pos_data[4];
+	obj->wx = pos_data[3] & 0x0f;
+	obj->wy = pos_data[3] >> 4;
+
+	rmi_2d_sensor_abs_process(sensor, obj, n_finger);
+}
+
+static inline u8 rmi_f11_parse_finger_state(const u8 *f_state, u8 n_finger)
+{
+	return (f_state[n_finger / 4] >> (2 * (n_finger % 4))) &
+							FINGER_STATE_MASK;
+}
+
+static void rmi_f11_finger_handler(struct f11_data *f11,
+				   struct rmi_2d_sensor *sensor,
+				   unsigned long *irq_bits, int num_irq_regs)
+{
+	const u8 *f_state = f11->data.f_state;
+	u8 finger_state;
+	u8 i;
+
+	int abs_bits = bitmap_and(f11->result_bits, irq_bits, f11->abs_mask,
+				  num_irq_regs * 8);
+	int rel_bits = bitmap_and(f11->result_bits, irq_bits, f11->rel_mask,
+				  num_irq_regs * 8);
+
+	for (i = 0; i < sensor->nbr_fingers; i++) {
+		/* Possible of having 4 fingers per f_statet register */
+		finger_state = rmi_f11_parse_finger_state(f_state, i);
+		if (finger_state == F11_RESERVED) {
+			pr_err("Invalid finger state[%d]: 0x%02x", i,
+				finger_state);
+			continue;
+		}
+
+		if (abs_bits)
+			rmi_f11_abs_pos_process(f11, sensor, &sensor->objs[i],
+							finger_state, i);
+
+		if (rel_bits)
+			rmi_f11_rel_pos_report(f11, i);
+	}
+
+	if (abs_bits) {
+		/*
+		 * the absolute part is made in 2 parts to allow the kernel
+		 * tracking to take place.
+		 */
+		if (sensor->kernel_tracking)
+			input_mt_assign_slots(sensor->input,
+					      sensor->tracking_slots,
+					      sensor->tracking_pos,
+					      sensor->nbr_fingers,
+					      sensor->dmax);
+
+		for (i = 0; i < sensor->nbr_fingers; i++) {
+			finger_state = rmi_f11_parse_finger_state(f_state, i);
+			if (finger_state == F11_RESERVED)
+				/* no need to send twice the error */
+				continue;
+
+			rmi_2d_sensor_abs_report(sensor, &sensor->objs[i], i);
+		}
+
+		input_mt_sync_frame(sensor->input);
+	}
+}
+
+static int f11_2d_construct_data(struct f11_data *f11)
+{
+	struct rmi_2d_sensor *sensor = &f11->sensor;
+	struct f11_2d_sensor_queries *query = &f11->sens_query;
+	struct f11_2d_data *data = &f11->data;
+	int i;
+
+	sensor->nbr_fingers = (query->nr_fingers == 5 ? 10 :
+				query->nr_fingers + 1);
+
+	sensor->pkt_size = DIV_ROUND_UP(sensor->nbr_fingers, 4);
+
+	if (query->has_abs) {
+		sensor->pkt_size += (sensor->nbr_fingers * 5);
+		sensor->attn_size = sensor->pkt_size;
+	}
+
+	if (query->has_rel)
+		sensor->pkt_size +=  (sensor->nbr_fingers * 2);
+
+	/* Check if F11_2D_Query7 is non-zero */
+	if (query->query7_nonzero)
+		sensor->pkt_size += sizeof(u8);
+
+	/* Check if F11_2D_Query7 or F11_2D_Query8 is non-zero */
+	if (query->query7_nonzero || query->query8_nonzero)
+		sensor->pkt_size += sizeof(u8);
+
+	if (query->has_pinch || query->has_flick || query->has_rotate) {
+		sensor->pkt_size += 3;
+		if (!query->has_flick)
+			sensor->pkt_size--;
+		if (!query->has_rotate)
+			sensor->pkt_size--;
+	}
+
+	if (query->has_touch_shapes)
+		sensor->pkt_size +=
+			DIV_ROUND_UP(query->nr_touch_shapes + 1, 8);
+
+	sensor->data_pkt = devm_kzalloc(&sensor->fn->dev, sensor->pkt_size,
+					GFP_KERNEL);
+	if (!sensor->data_pkt)
+		return -ENOMEM;
+
+	data->f_state = sensor->data_pkt;
+	i = DIV_ROUND_UP(sensor->nbr_fingers, 4);
+
+	if (query->has_abs) {
+		data->abs_pos = &sensor->data_pkt[i];
+		i += (sensor->nbr_fingers * RMI_F11_ABS_BYTES);
+	}
+
+	if (query->has_rel) {
+		data->rel_pos = &sensor->data_pkt[i];
+		i += (sensor->nbr_fingers * RMI_F11_REL_BYTES);
+	}
+
+	if (query->query7_nonzero) {
+		data->gest_1 = &sensor->data_pkt[i];
+		i++;
+	}
+
+	if (query->query7_nonzero || query->query8_nonzero) {
+		data->gest_2 = &sensor->data_pkt[i];
+		i++;
+	}
+
+	if (query->has_pinch) {
+		data->pinch = &sensor->data_pkt[i];
+		i++;
+	}
+
+	if (query->has_flick) {
+		if (query->has_pinch) {
+			data->flick = data->pinch;
+			i += 2;
+		} else {
+			data->flick = &sensor->data_pkt[i];
+			i += 3;
+		}
+	}
+
+	if (query->has_rotate) {
+		if (query->has_flick) {
+			data->rotate = data->flick + 1;
+		} else {
+			data->rotate = &sensor->data_pkt[i];
+			i += 2;
+		}
+	}
+
+	if (query->has_touch_shapes)
+		data->shapes = &sensor->data_pkt[i];
+
+	return 0;
+}
+
+static int f11_read_control_regs(struct rmi_function *fn,
+				struct f11_2d_ctrl *ctrl, u16 ctrl_base_addr) {
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	int error = 0;
+
+	ctrl->ctrl0_11_address = ctrl_base_addr;
+	error = rmi_read_block(rmi_dev, ctrl_base_addr, ctrl->ctrl0_11,
+				RMI_F11_CTRL_REG_COUNT);
+	if (error < 0) {
+		dev_err(&fn->dev, "Failed to read ctrl0, code: %d.\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int f11_write_control_regs(struct rmi_function *fn,
+					struct f11_2d_sensor_queries *query,
+					struct f11_2d_ctrl *ctrl,
+					u16 ctrl_base_addr)
+{
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	int error;
+
+	error = rmi_write_block(rmi_dev, ctrl_base_addr, ctrl->ctrl0_11,
+				RMI_F11_CTRL_REG_COUNT);
+	if (error < 0)
+		return error;
+
+	return 0;
+}
+
+static int rmi_f11_get_query_parameters(struct rmi_device *rmi_dev,
+			struct f11_data *f11,
+			struct f11_2d_sensor_queries *sensor_query,
+			u16 query_base_addr)
+{
+	int query_size;
+	int rc;
+	u8 query_buf[RMI_F11_QUERY_SIZE];
+	bool has_query36 = false;
+
+	rc = rmi_read_block(rmi_dev, query_base_addr, query_buf,
+				RMI_F11_QUERY_SIZE);
+	if (rc < 0)
+		return rc;
+
+	sensor_query->nr_fingers = query_buf[0] & RMI_F11_NR_FINGERS_MASK;
+	sensor_query->has_rel = !!(query_buf[0] & RMI_F11_HAS_REL);
+	sensor_query->has_abs = !!(query_buf[0] & RMI_F11_HAS_ABS);
+	sensor_query->has_gestures = !!(query_buf[0] & RMI_F11_HAS_GESTURES);
+	sensor_query->has_sensitivity_adjust =
+		!!(query_buf[0] && RMI_F11_HAS_SENSITIVITY_ADJ);
+	sensor_query->configurable = !!(query_buf[0] & RMI_F11_CONFIGURABLE);
+
+	sensor_query->nr_x_electrodes =
+				query_buf[1] & RMI_F11_NR_ELECTRODES_MASK;
+	sensor_query->nr_y_electrodes =
+				query_buf[2] & RMI_F11_NR_ELECTRODES_MASK;
+	sensor_query->max_electrodes =
+				query_buf[3] & RMI_F11_NR_ELECTRODES_MASK;
+
+	query_size = RMI_F11_QUERY_SIZE;
+
+	if (sensor_query->has_abs) {
+		rc = rmi_read(rmi_dev, query_base_addr + query_size, query_buf);
+		if (rc < 0)
+			return rc;
+
+		sensor_query->abs_data_size =
+			query_buf[0] & RMI_F11_ABS_DATA_SIZE_MASK;
+		sensor_query->has_anchored_finger =
+			!!(query_buf[0] & RMI_F11_HAS_ANCHORED_FINGER);
+		sensor_query->has_adj_hyst =
+			!!(query_buf[0] & RMI_F11_HAS_ADJ_HYST);
+		sensor_query->has_dribble =
+			!!(query_buf[0] & RMI_F11_HAS_DRIBBLE);
+		sensor_query->has_bending_correction =
+			!!(query_buf[0] & RMI_F11_HAS_BENDING_CORRECTION);
+		sensor_query->has_large_object_suppression =
+		!!(query_buf[0] && RMI_F11_HAS_LARGE_OBJECT_SUPPRESSION);
+		sensor_query->has_jitter_filter =
+			!!(query_buf[0] & RMI_F11_HAS_JITTER_FILTER);
+		query_size++;
+	}
+
+	if (sensor_query->has_rel) {
+		rc = rmi_read(rmi_dev, query_base_addr + query_size,
+					&sensor_query->f11_2d_query6);
+		if (rc < 0)
+			return rc;
+		query_size++;
+	}
+
+	if (sensor_query->has_gestures) {
+		rc = rmi_read_block(rmi_dev, query_base_addr + query_size,
+					query_buf, RMI_F11_QUERY_GESTURE_SIZE);
+		if (rc < 0)
+			return rc;
+
+		sensor_query->has_single_tap =
+			!!(query_buf[0] & RMI_F11_HAS_SINGLE_TAP);
+		sensor_query->has_tap_n_hold =
+			!!(query_buf[0] & RMI_F11_HAS_TAP_AND_HOLD);
+		sensor_query->has_double_tap =
+			!!(query_buf[0] & RMI_F11_HAS_DOUBLE_TAP);
+		sensor_query->has_early_tap =
+			!!(query_buf[0] & RMI_F11_HAS_EARLY_TAP);
+		sensor_query->has_flick =
+			!!(query_buf[0] & RMI_F11_HAS_FLICK);
+		sensor_query->has_press =
+			!!(query_buf[0] & RMI_F11_HAS_PRESS);
+		sensor_query->has_pinch =
+			!!(query_buf[0] & RMI_F11_HAS_PINCH);
+		sensor_query->has_chiral =
+			!!(query_buf[0] & RMI_F11_HAS_CHIRAL);
+
+		/* query 8 */
+		sensor_query->has_palm_det =
+			!!(query_buf[1] & RMI_F11_HAS_PALM_DET);
+		sensor_query->has_rotate =
+			!!(query_buf[1] & RMI_F11_HAS_ROTATE);
+		sensor_query->has_touch_shapes =
+			!!(query_buf[1] & RMI_F11_HAS_TOUCH_SHAPES);
+		sensor_query->has_scroll_zones =
+			!!(query_buf[1] & RMI_F11_HAS_SCROLL_ZONES);
+		sensor_query->has_individual_scroll_zones =
+			!!(query_buf[1] & RMI_F11_HAS_INDIVIDUAL_SCROLL_ZONES);
+		sensor_query->has_mf_scroll =
+			!!(query_buf[1] & RMI_F11_HAS_MF_SCROLL);
+		sensor_query->has_mf_edge_motion =
+			!!(query_buf[1] & RMI_F11_HAS_MF_EDGE_MOTION);
+		sensor_query->has_mf_scroll_inertia =
+			!!(query_buf[1] & RMI_F11_HAS_MF_SCROLL_INERTIA);
+
+		sensor_query->query7_nonzero = !!(query_buf[0]);
+		sensor_query->query8_nonzero = !!(query_buf[1]);
+
+		query_size += 2;
+	}
+
+	if (f11->has_query9) {
+		rc = rmi_read(rmi_dev, query_base_addr + query_size, query_buf);
+		if (rc < 0)
+			return rc;
+
+		sensor_query->has_pen =
+			!!(query_buf[0] & RMI_F11_HAS_PEN);
+		sensor_query->has_proximity =
+			!!(query_buf[0] & RMI_F11_HAS_PROXIMITY);
+		sensor_query->has_palm_det_sensitivity =
+			!!(query_buf[0] & RMI_F11_HAS_PALM_DET_SENSITIVITY);
+		sensor_query->has_suppress_on_palm_detect =
+			!!(query_buf[0] & RMI_F11_HAS_SUPPRESS_ON_PALM_DETECT);
+		sensor_query->has_two_pen_thresholds =
+			!!(query_buf[0] & RMI_F11_HAS_TWO_PEN_THRESHOLDS);
+		sensor_query->has_contact_geometry =
+			!!(query_buf[0] & RMI_F11_HAS_CONTACT_GEOMETRY);
+		sensor_query->has_pen_hover_discrimination =
+			!!(query_buf[0] & RMI_F11_HAS_PEN_HOVER_DISCRIMINATION);
+		sensor_query->has_pen_filters =
+			!!(query_buf[0] & RMI_F11_HAS_PEN_FILTERS);
+
+		query_size++;
+	}
+
+	if (sensor_query->has_touch_shapes) {
+		rc = rmi_read(rmi_dev, query_base_addr + query_size, query_buf);
+		if (rc < 0)
+			return rc;
+
+		sensor_query->nr_touch_shapes = query_buf[0] &
+				RMI_F11_NR_TOUCH_SHAPES_MASK;
+
+		query_size++;
+	}
+
+	if (f11->has_query11) {
+		rc = rmi_read(rmi_dev, query_base_addr + query_size, query_buf);
+		if (rc < 0)
+			return rc;
+
+		sensor_query->has_z_tuning =
+			!!(query_buf[0] & RMI_F11_HAS_Z_TUNING);
+		sensor_query->has_algorithm_selection =
+			!!(query_buf[0] & RMI_F11_HAS_ALGORITHM_SELECTION);
+		sensor_query->has_w_tuning =
+			!!(query_buf[0] & RMI_F11_HAS_W_TUNING);
+		sensor_query->has_pitch_info =
+			!!(query_buf[0] & RMI_F11_HAS_PITCH_INFO);
+		sensor_query->has_finger_size =
+			!!(query_buf[0] & RMI_F11_HAS_FINGER_SIZE);
+		sensor_query->has_segmentation_aggressiveness =
+			!!(query_buf[0] &
+				RMI_F11_HAS_SEGMENTATION_AGGRESSIVENESS);
+		sensor_query->has_XY_clip =
+			!!(query_buf[0] & RMI_F11_HAS_XY_CLIP);
+		sensor_query->has_drumming_filter =
+			!!(query_buf[0] & RMI_F11_HAS_DRUMMING_FILTER);
+
+		query_size++;
+	}
+
+	if (f11->has_query12) {
+		rc = rmi_read(rmi_dev, query_base_addr + query_size, query_buf);
+		if (rc < 0)
+			return rc;
+
+		sensor_query->has_gapless_finger =
+			!!(query_buf[0] & RMI_F11_HAS_GAPLESS_FINGER);
+		sensor_query->has_gapless_finger_tuning =
+			!!(query_buf[0] & RMI_F11_HAS_GAPLESS_FINGER_TUNING);
+		sensor_query->has_8bit_w =
+			!!(query_buf[0] & RMI_F11_HAS_8BIT_W);
+		sensor_query->has_adjustable_mapping =
+			!!(query_buf[0] & RMI_F11_HAS_ADJUSTABLE_MAPPING);
+		sensor_query->has_info2 =
+			!!(query_buf[0] & RMI_F11_HAS_INFO2);
+		sensor_query->has_physical_props =
+			!!(query_buf[0] & RMI_F11_HAS_PHYSICAL_PROPS);
+		sensor_query->has_finger_limit =
+			!!(query_buf[0] & RMI_F11_HAS_FINGER_LIMIT);
+		sensor_query->has_linear_coeff_2 =
+			!!(query_buf[0] & RMI_F11_HAS_LINEAR_COEFF);
+
+		query_size++;
+	}
+
+	if (sensor_query->has_jitter_filter) {
+		rc = rmi_read(rmi_dev, query_base_addr + query_size, query_buf);
+		if (rc < 0)
+			return rc;
+
+		sensor_query->jitter_window_size = query_buf[0] &
+			RMI_F11_JITTER_WINDOW_MASK;
+		sensor_query->jitter_filter_type = (query_buf[0] &
+			RMI_F11_JITTER_FILTER_MASK) >>
+			RMI_F11_JITTER_FILTER_SHIFT;
+
+		query_size++;
+	}
+
+	if (sensor_query->has_info2) {
+		rc = rmi_read(rmi_dev, query_base_addr + query_size, query_buf);
+		if (rc < 0)
+			return rc;
+
+		sensor_query->light_control =
+			query_buf[0] & RMI_F11_LIGHT_CONTROL_MASK;
+		sensor_query->is_clear =
+			!!(query_buf[0] & RMI_F11_IS_CLEAR);
+		sensor_query->clickpad_props =
+			(query_buf[0] & RMI_F11_CLICKPAD_PROPS_MASK) >>
+			RMI_F11_CLICKPAD_PROPS_SHIFT;
+		sensor_query->mouse_buttons =
+			(query_buf[0] & RMI_F11_MOUSE_BUTTONS_MASK) >>
+			RMI_F11_MOUSE_BUTTONS_SHIFT;
+		sensor_query->has_advanced_gestures =
+			!!(query_buf[0] & RMI_F11_HAS_ADVANCED_GESTURES);
+
+		query_size++;
+	}
+
+	if (sensor_query->has_physical_props) {
+		rc = rmi_read_block(rmi_dev, query_base_addr
+			+ query_size, query_buf, 4);
+		if (rc < 0)
+			return rc;
+
+		sensor_query->x_sensor_size_mm =
+			(query_buf[0] | (query_buf[1] << 8)) / 10;
+		sensor_query->y_sensor_size_mm =
+			(query_buf[2] | (query_buf[3] << 8)) / 10;
+
+		/*
+		 * query 15 - 18 contain the size of the sensor
+		 * and query 19 - 26 contain bezel dimensions
+		 */
+		query_size += 12;
+	}
+
+	if (f11->has_query27)
+		++query_size;
+
+	if (f11->has_query28) {
+		rc = rmi_read(rmi_dev, query_base_addr + query_size,
+				query_buf);
+		if (rc < 0)
+			return rc;
+
+		has_query36 = !!(query_buf[0] & BIT(6));
+	}
+
+	if (has_query36) {
+		query_size += 2;
+		rc = rmi_read(rmi_dev, query_base_addr + query_size,
+				query_buf);
+		if (rc < 0)
+			return rc;
+
+		if (!!(query_buf[0] & BIT(5)))
+			f11->has_acm = true;
+	}
+
+	return query_size;
+}
+
+static int rmi_f11_initialize(struct rmi_function *fn)
+{
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	struct f11_data *f11;
+	struct f11_2d_ctrl *ctrl;
+	u8 query_offset;
+	u16 query_base_addr;
+	u16 control_base_addr;
+	u16 max_x_pos, max_y_pos;
+	int rc;
+	const struct rmi_device_platform_data *pdata =
+				rmi_get_platform_data(rmi_dev);
+	struct rmi_driver_data *drvdata = dev_get_drvdata(&rmi_dev->dev);
+	struct rmi_2d_sensor *sensor;
+	u8 buf;
+	int mask_size;
+
+	rmi_dbg(RMI_DEBUG_FN, &fn->dev, "Initializing F11 values.\n");
+
+	mask_size = BITS_TO_LONGS(drvdata->irq_count) * sizeof(unsigned long);
+
+	/*
+	** init instance data, fill in values and create any sysfs files
+	*/
+	f11 = devm_kzalloc(&fn->dev, sizeof(struct f11_data) + mask_size * 3,
+			GFP_KERNEL);
+	if (!f11)
+		return -ENOMEM;
+
+	if (fn->dev.of_node) {
+		rc = rmi_2d_sensor_of_probe(&fn->dev, &f11->sensor_pdata);
+		if (rc)
+			return rc;
+	} else if (pdata->sensor_pdata) {
+		f11->sensor_pdata = *pdata->sensor_pdata;
+	}
+
+	f11->rezero_wait_ms = f11->sensor_pdata.rezero_wait;
+
+	f11->abs_mask = (unsigned long *)((char *)f11
+			+ sizeof(struct f11_data));
+	f11->rel_mask = (unsigned long *)((char *)f11
+			+ sizeof(struct f11_data) + mask_size);
+	f11->result_bits = (unsigned long *)((char *)f11
+			+ sizeof(struct f11_data) + mask_size * 2);
+
+	set_bit(fn->irq_pos, f11->abs_mask);
+	set_bit(fn->irq_pos + 1, f11->rel_mask);
+
+	query_base_addr = fn->fd.query_base_addr;
+	control_base_addr = fn->fd.control_base_addr;
+
+	rc = rmi_read(rmi_dev, query_base_addr, &buf);
+	if (rc < 0)
+		return rc;
+
+	f11->has_query9 = !!(buf & RMI_F11_HAS_QUERY9);
+	f11->has_query11 = !!(buf & RMI_F11_HAS_QUERY11);
+	f11->has_query12 = !!(buf & RMI_F11_HAS_QUERY12);
+	f11->has_query27 = !!(buf & RMI_F11_HAS_QUERY27);
+	f11->has_query28 = !!(buf & RMI_F11_HAS_QUERY28);
+
+	query_offset = (query_base_addr + 1);
+	sensor = &f11->sensor;
+	sensor->fn = fn;
+
+	rc = rmi_f11_get_query_parameters(rmi_dev, f11,
+			&f11->sens_query, query_offset);
+	if (rc < 0)
+		return rc;
+	query_offset += rc;
+
+	rc = f11_read_control_regs(fn, &f11->dev_controls,
+			control_base_addr);
+	if (rc < 0) {
+		dev_err(&fn->dev,
+			"Failed to read F11 control params.\n");
+		return rc;
+	}
+
+	if (f11->sens_query.has_info2) {
+		if (f11->sens_query.is_clear)
+			f11->sensor.sensor_type = rmi_sensor_touchscreen;
+		else
+			f11->sensor.sensor_type = rmi_sensor_touchpad;
+	}
+
+	sensor->report_abs = f11->sens_query.has_abs;
+
+	sensor->axis_align =
+		f11->sensor_pdata.axis_align;
+
+	sensor->topbuttonpad = f11->sensor_pdata.topbuttonpad;
+	sensor->kernel_tracking = f11->sensor_pdata.kernel_tracking;
+	sensor->dmax = f11->sensor_pdata.dmax;
+
+	if (f11->sens_query.has_physical_props) {
+		sensor->x_mm = f11->sens_query.x_sensor_size_mm;
+		sensor->y_mm = f11->sens_query.y_sensor_size_mm;
+	} else {
+		sensor->x_mm = f11->sensor_pdata.x_mm;
+		sensor->y_mm = f11->sensor_pdata.y_mm;
+	}
+
+	if (sensor->sensor_type == rmi_sensor_default)
+		sensor->sensor_type =
+			f11->sensor_pdata.sensor_type;
+
+	sensor->report_abs = sensor->report_abs
+		&& !(f11->sensor_pdata.disable_report_mask
+			& RMI_F11_DISABLE_ABS_REPORT);
+
+	if (!sensor->report_abs)
+		/*
+		 * If device doesn't have abs or if it has been disables
+		 * fallback to reporting rel data.
+		 */
+		sensor->report_rel = f11->sens_query.has_rel;
+
+	rc = rmi_read_block(rmi_dev,
+		control_base_addr + F11_CTRL_SENSOR_MAX_X_POS_OFFSET,
+		(u8 *)&max_x_pos, sizeof(max_x_pos));
+	if (rc < 0)
+		return rc;
+
+	rc = rmi_read_block(rmi_dev,
+		control_base_addr + F11_CTRL_SENSOR_MAX_Y_POS_OFFSET,
+		(u8 *)&max_y_pos, sizeof(max_y_pos));
+	if (rc < 0)
+		return rc;
+
+	sensor->max_x = max_x_pos;
+	sensor->max_y = max_y_pos;
+
+	rc = f11_2d_construct_data(f11);
+	if (rc < 0)
+		return rc;
+
+	if (f11->has_acm)
+		f11->sensor.attn_size += f11->sensor.nbr_fingers * 2;
+
+	/* allocate the in-kernel tracking buffers */
+	sensor->tracking_pos = devm_kzalloc(&fn->dev,
+			sizeof(struct input_mt_pos) * sensor->nbr_fingers,
+			GFP_KERNEL);
+	sensor->tracking_slots = devm_kzalloc(&fn->dev,
+			sizeof(int) * sensor->nbr_fingers, GFP_KERNEL);
+	sensor->objs = devm_kzalloc(&fn->dev,
+			sizeof(struct rmi_2d_sensor_abs_object)
+			* sensor->nbr_fingers, GFP_KERNEL);
+	if (!sensor->tracking_pos || !sensor->tracking_slots || !sensor->objs)
+		return -ENOMEM;
+
+	ctrl = &f11->dev_controls;
+	if (sensor->axis_align.delta_x_threshold)
+		ctrl->ctrl0_11[RMI_F11_DELTA_X_THRESHOLD] =
+			sensor->axis_align.delta_x_threshold;
+
+	if (sensor->axis_align.delta_y_threshold)
+		ctrl->ctrl0_11[RMI_F11_DELTA_Y_THRESHOLD] =
+			sensor->axis_align.delta_y_threshold;
+
+	if (f11->sens_query.has_dribble)
+		ctrl->ctrl0_11[0] = ctrl->ctrl0_11[0] & ~BIT(6);
+
+	if (f11->sens_query.has_palm_det)
+		ctrl->ctrl0_11[11] = ctrl->ctrl0_11[11] & ~BIT(0);
+
+	rc = f11_write_control_regs(fn, &f11->sens_query,
+			   &f11->dev_controls, fn->fd.query_base_addr);
+	if (rc)
+		dev_warn(&fn->dev, "Failed to write control registers\n");
+
+	mutex_init(&f11->dev_controls_mutex);
+
+	dev_set_drvdata(&fn->dev, f11);
+
+	return 0;
+}
+
+static int rmi_f11_config(struct rmi_function *fn)
+{
+	struct f11_data *f11 = dev_get_drvdata(&fn->dev);
+	struct rmi_driver *drv = fn->rmi_dev->driver;
+	struct rmi_2d_sensor *sensor = &f11->sensor;
+	int rc;
+
+	if (!sensor->report_abs)
+		drv->clear_irq_bits(fn->rmi_dev, f11->abs_mask);
+	else
+		drv->set_irq_bits(fn->rmi_dev, f11->abs_mask);
+
+	if (!sensor->report_rel)
+		drv->clear_irq_bits(fn->rmi_dev, f11->rel_mask);
+	else
+		drv->set_irq_bits(fn->rmi_dev, f11->rel_mask);
+
+	rc = f11_write_control_regs(fn, &f11->sens_query,
+			   &f11->dev_controls, fn->fd.query_base_addr);
+	if (rc < 0)
+		return rc;
+
+	return 0;
+}
+
+static int rmi_f11_attention(struct rmi_function *fn, unsigned long *irq_bits)
+{
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	struct rmi_driver_data *drvdata = dev_get_drvdata(&rmi_dev->dev);
+	struct f11_data *f11 = dev_get_drvdata(&fn->dev);
+	u16 data_base_addr = fn->fd.data_base_addr;
+	u16 data_base_addr_offset = 0;
+	int error;
+
+	if (rmi_dev->xport->attn_data) {
+		memcpy(f11->sensor.data_pkt, rmi_dev->xport->attn_data,
+			f11->sensor.attn_size);
+		rmi_dev->xport->attn_data += f11->sensor.attn_size;
+		rmi_dev->xport->attn_size -= f11->sensor.attn_size;
+	} else {
+		error = rmi_read_block(rmi_dev,
+				data_base_addr + data_base_addr_offset,
+				f11->sensor.data_pkt,
+				f11->sensor.pkt_size);
+		if (error < 0)
+			return error;
+	}
+
+	rmi_f11_finger_handler(f11, &f11->sensor, irq_bits,
+				drvdata->num_of_irq_regs);
+	data_base_addr_offset += f11->sensor.pkt_size;
+
+	return 0;
+}
+
+static int rmi_f11_resume(struct rmi_function *fn)
+{
+	struct f11_data *f11 = dev_get_drvdata(&fn->dev);
+	int error;
+
+	rmi_dbg(RMI_DEBUG_FN, &fn->dev, "Resuming...\n");
+	if (!f11->rezero_wait_ms)
+		return 0;
+
+	mdelay(f11->rezero_wait_ms);
+
+	error = rmi_write(fn->rmi_dev, fn->fd.command_base_addr,
+				RMI_F11_REZERO);
+	if (error) {
+		dev_err(&fn->dev,
+			"%s: failed to issue rezero command, error = %d.",
+			__func__, error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int rmi_f11_probe(struct rmi_function *fn)
+{
+	int error;
+	struct f11_data *f11;
+
+	error = rmi_f11_initialize(fn);
+	if (error)
+		return error;
+
+	f11 = dev_get_drvdata(&fn->dev);
+	error = rmi_2d_sensor_configure_input(fn, &f11->sensor);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+struct rmi_function_handler rmi_f11_handler = {
+	.driver = {
+		.name	= "rmi4_f11",
+	},
+	.func		= 0x11,
+	.probe		= rmi_f11_probe,
+	.config		= rmi_f11_config,
+	.attention	= rmi_f11_attention,
+	.resume		= rmi_f11_resume,
+};

drivers/input/rmi4/rmi_f12.c

@@ -0,0 +1,457 @@
+/*
+ * Copyright (c) 2012-2016 Synaptics Incorporated
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/rmi.h>
+#include "rmi_driver.h"
+#include "rmi_2d_sensor.h"
+
+enum rmi_f12_object_type {
+	RMI_F12_OBJECT_NONE			= 0x00,
+	RMI_F12_OBJECT_FINGER			= 0x01,
+	RMI_F12_OBJECT_STYLUS			= 0x02,
+	RMI_F12_OBJECT_PALM			= 0x03,
+	RMI_F12_OBJECT_UNCLASSIFIED		= 0x04,
+	RMI_F12_OBJECT_GLOVED_FINGER		= 0x06,
+	RMI_F12_OBJECT_NARROW_OBJECT		= 0x07,
+	RMI_F12_OBJECT_HAND_EDGE		= 0x08,
+	RMI_F12_OBJECT_COVER			= 0x0A,
+	RMI_F12_OBJECT_STYLUS_2			= 0x0B,
+	RMI_F12_OBJECT_ERASER			= 0x0C,
+	RMI_F12_OBJECT_SMALL_OBJECT		= 0x0D,
+};
+
+struct f12_data {
+	struct rmi_function *fn;
+	struct rmi_2d_sensor sensor;
+	struct rmi_2d_sensor_platform_data sensor_pdata;
+
+	u16 data_addr;
+
+	struct rmi_register_descriptor query_reg_desc;
+	struct rmi_register_descriptor control_reg_desc;
+	struct rmi_register_descriptor data_reg_desc;
+
+	/* F12 Data1 describes sensed objects */
+	const struct rmi_register_desc_item *data1;
+	u16 data1_offset;
+
+	/* F12 Data5 describes finger ACM */
+	const struct rmi_register_desc_item *data5;
+	u16 data5_offset;
+
+	/* F12 Data5 describes Pen */
+	const struct rmi_register_desc_item *data6;
+	u16 data6_offset;
+
+
+	/* F12 Data9 reports relative data */
+	const struct rmi_register_desc_item *data9;
+	u16 data9_offset;
+
+	const struct rmi_register_desc_item *data15;
+	u16 data15_offset;
+};
+
+static int rmi_f12_read_sensor_tuning(struct f12_data *f12)
+{
+	const struct rmi_register_desc_item *item;
+	struct rmi_2d_sensor *sensor = &f12->sensor;
+	struct rmi_function *fn = sensor->fn;
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	int ret;
+	int offset;
+	u8 buf[14];
+	int pitch_x = 0;
+	int pitch_y = 0;
+	int clip_x_low = 0;
+	int clip_x_high = 0;
+	int clip_y_low = 0;
+	int clip_y_high = 0;
+	int rx_receivers = 0;
+	int tx_receivers = 0;
+	int sensor_flags = 0;
+
+	item = rmi_get_register_desc_item(&f12->control_reg_desc, 8);
+	if (!item) {
+		dev_err(&fn->dev,
+			"F12 does not have the sensor tuning control register\n");
+		return -ENODEV;
+	}
+
+	offset = rmi_register_desc_calc_reg_offset(&f12->control_reg_desc, 8);
+
+	if (item->reg_size > 14) {
+		dev_err(&fn->dev, "F12 control8 should be 14 bytes, not: %ld\n",
+			item->reg_size);
+		return -ENODEV;
+	}
+
+	ret = rmi_read_block(rmi_dev, fn->fd.control_base_addr + offset, buf,
+				item->reg_size);
+	if (ret)
+		return ret;
+
+	offset = 0;
+	if (rmi_register_desc_has_subpacket(item, 0)) {
+		sensor->max_x = (buf[offset + 1] << 8) | buf[offset];
+		sensor->max_y = (buf[offset + 3] << 8) | buf[offset + 2];
+		offset += 4;
+	}
+
+	rmi_dbg(RMI_DEBUG_FN, &fn->dev, "%s: max_x: %d max_y: %d\n", __func__,
+		sensor->max_x, sensor->max_y);
+
+	if (rmi_register_desc_has_subpacket(item, 1)) {
+		pitch_x = (buf[offset + 1] << 8) | buf[offset];
+		pitch_y	= (buf[offset + 3] << 8) | buf[offset + 2];
+		offset += 4;
+	}
+
+	if (rmi_register_desc_has_subpacket(item, 2)) {
+		sensor->axis_align.clip_x_low = buf[offset];
+		sensor->axis_align.clip_x_high = sensor->max_x
+							- buf[offset + 1];
+		sensor->axis_align.clip_y_low = buf[offset + 2];
+		sensor->axis_align.clip_y_high = sensor->max_y
+							- buf[offset + 3];
+		offset += 4;
+	}
+
+	rmi_dbg(RMI_DEBUG_FN, &fn->dev, "%s: x low: %d x high: %d y low: %d y high: %d\n",
+		__func__, clip_x_low, clip_x_high, clip_y_low, clip_y_high);
+
+	if (rmi_register_desc_has_subpacket(item, 3)) {
+		rx_receivers = buf[offset];
+		tx_receivers = buf[offset + 1];
+		offset += 2;
+	}
+
+	if (rmi_register_desc_has_subpacket(item, 4)) {
+		sensor_flags = buf[offset];
+		offset += 1;
+	}
+
+	sensor->x_mm = (pitch_x * rx_receivers) >> 12;
+	sensor->y_mm = (pitch_y * tx_receivers) >> 12;
+
+	rmi_dbg(RMI_DEBUG_FN, &fn->dev, "%s: x_mm: %d y_mm: %d\n", __func__,
+		sensor->x_mm, sensor->y_mm);
+
+	return 0;
+}
+
+static void rmi_f12_process_objects(struct f12_data *f12, u8 *data1)
+{
+	int i;
+	struct rmi_2d_sensor *sensor = &f12->sensor;
+
+	for (i = 0; i < f12->data1->num_subpackets; i++) {
+		struct rmi_2d_sensor_abs_object *obj = &sensor->objs[i];
+
+		obj->type = RMI_2D_OBJECT_NONE;
+		obj->mt_tool = MT_TOOL_FINGER;
+
+		switch (data1[0]) {
+		case RMI_F12_OBJECT_FINGER:
+			obj->type = RMI_2D_OBJECT_FINGER;
+			break;
+		case RMI_F12_OBJECT_STYLUS:
+			obj->type = RMI_2D_OBJECT_STYLUS;
+			obj->mt_tool = MT_TOOL_PEN;
+			break;
+		case RMI_F12_OBJECT_PALM:
+			obj->type = RMI_2D_OBJECT_PALM;
+			obj->mt_tool = MT_TOOL_PALM;
+			break;
+		case RMI_F12_OBJECT_UNCLASSIFIED:
+			obj->type = RMI_2D_OBJECT_UNCLASSIFIED;
+			break;
+		}
+
+		obj->x = (data1[2] << 8) | data1[1];
+		obj->y = (data1[4] << 8) | data1[3];
+		obj->z = data1[5];
+		obj->wx = data1[6];
+		obj->wy = data1[7];
+
+		rmi_2d_sensor_abs_process(sensor, obj, i);
+
+		data1 += 8;
+	}
+
+	if (sensor->kernel_tracking)
+		input_mt_assign_slots(sensor->input,
+				      sensor->tracking_slots,
+				      sensor->tracking_pos,
+				      sensor->nbr_fingers,
+				      sensor->dmax);
+
+	for (i = 0; i < sensor->nbr_fingers; i++)
+		rmi_2d_sensor_abs_report(sensor, &sensor->objs[i], i);
+}
+
+static int rmi_f12_attention(struct rmi_function *fn,
+			     unsigned long *irq_nr_regs)
+{
+	int retval;
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	struct f12_data *f12 = dev_get_drvdata(&fn->dev);
+	struct rmi_2d_sensor *sensor = &f12->sensor;
+
+	if (rmi_dev->xport->attn_data) {
+		memcpy(sensor->data_pkt, rmi_dev->xport->attn_data,
+			sensor->attn_size);
+		rmi_dev->xport->attn_data += sensor->attn_size;
+		rmi_dev->xport->attn_size -= sensor->attn_size;
+	} else {
+		retval = rmi_read_block(rmi_dev, f12->data_addr,
+					sensor->data_pkt, sensor->pkt_size);
+		if (retval < 0) {
+			dev_err(&fn->dev, "Failed to read object data. Code: %d.\n",
+				retval);
+			return retval;
+		}
+	}
+
+	if (f12->data1)
+		rmi_f12_process_objects(f12,
+			&sensor->data_pkt[f12->data1_offset]);
+
+	input_mt_sync_frame(sensor->input);
+
+	return 0;
+}
+
+static int rmi_f12_config(struct rmi_function *fn)
+{
+	struct rmi_driver *drv = fn->rmi_dev->driver;
+
+	drv->set_irq_bits(fn->rmi_dev, fn->irq_mask);
+
+	return 0;
+}
+
+static int rmi_f12_probe(struct rmi_function *fn)
+{
+	struct f12_data *f12;
+	int ret;
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	char buf;
+	u16 query_addr = fn->fd.query_base_addr;
+	const struct rmi_register_desc_item *item;
+	struct rmi_2d_sensor *sensor;
+	struct rmi_device_platform_data *pdata = rmi_get_platform_data(rmi_dev);
+	struct rmi_transport_dev *xport = rmi_dev->xport;
+	u16 data_offset = 0;
+
+	rmi_dbg(RMI_DEBUG_FN, &fn->dev, "%s\n", __func__);
+
+	ret = rmi_read(fn->rmi_dev, query_addr, &buf);
+	if (ret < 0) {
+		dev_err(&fn->dev, "Failed to read general info register: %d\n",
+			ret);
+		return -ENODEV;
+	}
+	++query_addr;
+
+	if (!(buf & 0x1)) {
+		dev_err(&fn->dev,
+			"Behavior of F12 without register descriptors is undefined.\n");
+		return -ENODEV;
+	}
+
+	f12 = devm_kzalloc(&fn->dev, sizeof(struct f12_data), GFP_KERNEL);
+	if (!f12)
+		return -ENOMEM;
+
+	if (fn->dev.of_node) {
+		ret = rmi_2d_sensor_of_probe(&fn->dev, &f12->sensor_pdata);
+		if (ret)
+			return ret;
+	} else if (pdata->sensor_pdata) {
+		f12->sensor_pdata = *pdata->sensor_pdata;
+	}
+
+	ret = rmi_read_register_desc(rmi_dev, query_addr,
+					&f12->query_reg_desc);
+	if (ret) {
+		dev_err(&fn->dev,
+			"Failed to read the Query Register Descriptor: %d\n",
+			ret);
+		return ret;
+	}
+	query_addr += 3;
+
+	ret = rmi_read_register_desc(rmi_dev, query_addr,
+						&f12->control_reg_desc);
+	if (ret) {
+		dev_err(&fn->dev,
+			"Failed to read the Control Register Descriptor: %d\n",
+			ret);
+		return ret;
+	}
+	query_addr += 3;
+
+	ret = rmi_read_register_desc(rmi_dev, query_addr,
+						&f12->data_reg_desc);
+	if (ret) {
+		dev_err(&fn->dev,
+			"Failed to read the Data Register Descriptor: %d\n",
+			ret);
+		return ret;
+	}
+	query_addr += 3;
+
+	sensor = &f12->sensor;
+	sensor->fn = fn;
+	f12->data_addr = fn->fd.data_base_addr;
+	sensor->pkt_size = rmi_register_desc_calc_size(&f12->data_reg_desc);
+
+	sensor->axis_align =
+		f12->sensor_pdata.axis_align;
+
+	sensor->x_mm = f12->sensor_pdata.x_mm;
+	sensor->y_mm = f12->sensor_pdata.y_mm;
+
+	if (sensor->sensor_type == rmi_sensor_default)
+		sensor->sensor_type =
+			f12->sensor_pdata.sensor_type;
+
+	rmi_dbg(RMI_DEBUG_FN, &fn->dev, "%s: data packet size: %d\n", __func__,
+		sensor->pkt_size);
+	sensor->data_pkt = devm_kzalloc(&fn->dev, sensor->pkt_size, GFP_KERNEL);
+	if (!sensor->data_pkt)
+		return -ENOMEM;
+
+	dev_set_drvdata(&fn->dev, f12);
+
+	ret = rmi_f12_read_sensor_tuning(f12);
+	if (ret)
+		return ret;
+
+	/*
+	 * Figure out what data is contained in the data registers. HID devices
+	 * may have registers defined, but their data is not reported in the
+	 * HID attention report. Registers which are not reported in the HID
+	 * attention report check to see if the device is receiving data from
+	 * HID attention reports.
+	 */
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 0);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 1);
+	if (item) {
+		f12->data1 = item;
+		f12->data1_offset = data_offset;
+		data_offset += item->reg_size;
+		sensor->nbr_fingers = item->num_subpackets;
+		sensor->report_abs = 1;
+		sensor->attn_size += item->reg_size;
+	}
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 2);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 3);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 4);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 5);
+	if (item) {
+		f12->data5 = item;
+		f12->data5_offset = data_offset;
+		data_offset += item->reg_size;
+		sensor->attn_size += item->reg_size;
+	}
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 6);
+	if (item && !xport->attn_data) {
+		f12->data6 = item;
+		f12->data6_offset = data_offset;
+		data_offset += item->reg_size;
+	}
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 7);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 8);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 9);
+	if (item && !xport->attn_data) {
+		f12->data9 = item;
+		f12->data9_offset = data_offset;
+		data_offset += item->reg_size;
+		if (!sensor->report_abs)
+			sensor->report_rel = 1;
+	}
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 10);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 11);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 12);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 13);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 14);
+	if (item && !xport->attn_data)
+		data_offset += item->reg_size;
+
+	item = rmi_get_register_desc_item(&f12->data_reg_desc, 15);
+	if (item && !xport->attn_data) {
+		f12->data15 = item;
+		f12->data15_offset = data_offset;
+		data_offset += item->reg_size;
+	}
+
+	/* allocate the in-kernel tracking buffers */
+	sensor->tracking_pos = devm_kzalloc(&fn->dev,
+			sizeof(struct input_mt_pos) * sensor->nbr_fingers,
+			GFP_KERNEL);
+	sensor->tracking_slots = devm_kzalloc(&fn->dev,
+			sizeof(int) * sensor->nbr_fingers, GFP_KERNEL);
+	sensor->objs = devm_kzalloc(&fn->dev,
+			sizeof(struct rmi_2d_sensor_abs_object)
+			* sensor->nbr_fingers, GFP_KERNEL);
+	if (!sensor->tracking_pos || !sensor->tracking_slots || !sensor->objs)
+		return -ENOMEM;
+
+	ret = rmi_2d_sensor_configure_input(fn, sensor);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+struct rmi_function_handler rmi_f12_handler = {
+	.driver = {
+		.name = "rmi4_f12",
+	},
+	.func = 0x12,
+	.probe = rmi_f12_probe,
+	.config = rmi_f12_config,
+	.attention = rmi_f12_attention,
+};

drivers/input/rmi4/rmi_f30.c

@@ -0,0 +1,407 @@
+/*
+ * Copyright (c) 2012-2016 Synaptics Incorporated
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/rmi.h>
+#include <linux/input.h>
+#include <linux/slab.h>
+#include "rmi_driver.h"
+
+#define RMI_F30_QUERY_SIZE			2
+
+/* Defs for Query 0 */
+#define RMI_F30_EXTENDED_PATTERNS		0x01
+#define RMI_F30_HAS_MAPPABLE_BUTTONS		(1 << 1)
+#define RMI_F30_HAS_LED			(1 << 2)
+#define RMI_F30_HAS_GPIO			(1 << 3)
+#define RMI_F30_HAS_HAPTIC			(1 << 4)
+#define RMI_F30_HAS_GPIO_DRV_CTL		(1 << 5)
+#define RMI_F30_HAS_MECH_MOUSE_BTNS		(1 << 6)
+
+/* Defs for Query 1 */
+#define RMI_F30_GPIO_LED_COUNT			0x1F
+
+/* Defs for Control Registers */
+#define RMI_F30_CTRL_1_GPIO_DEBOUNCE		0x01
+#define RMI_F30_CTRL_1_HALT			(1 << 4)
+#define RMI_F30_CTRL_1_HALTED			(1 << 5)
+#define RMI_F30_CTRL_10_NUM_MECH_MOUSE_BTNS	0x03
+
+struct rmi_f30_ctrl_data {
+	int address;
+	int length;
+	u8 *regs;
+};
+
+#define RMI_F30_CTRL_MAX_REGS		32
+#define RMI_F30_CTRL_MAX_BYTES		((RMI_F30_CTRL_MAX_REGS + 7) >> 3)
+#define RMI_F30_CTRL_MAX_REG_BLOCKS	11
+
+#define RMI_F30_CTRL_REGS_MAX_SIZE (RMI_F30_CTRL_MAX_BYTES		\
+					+ 1				\
+					+ RMI_F30_CTRL_MAX_BYTES	\
+					+ RMI_F30_CTRL_MAX_BYTES	\
+					+ RMI_F30_CTRL_MAX_BYTES	\
+					+ 6				\
+					+ RMI_F30_CTRL_MAX_REGS		\
+					+ RMI_F30_CTRL_MAX_REGS		\
+					+ RMI_F30_CTRL_MAX_BYTES	\
+					+ 1				\
+					+ 1)
+
+struct f30_data {
+	/* Query Data */
+	bool has_extended_pattern;
+	bool has_mappable_buttons;
+	bool has_led;
+	bool has_gpio;
+	bool has_haptic;
+	bool has_gpio_driver_control;
+	bool has_mech_mouse_btns;
+	u8 gpioled_count;
+
+	u8 register_count;
+
+	/* Control Register Data */
+	struct rmi_f30_ctrl_data ctrl[RMI_F30_CTRL_MAX_REG_BLOCKS];
+	u8 ctrl_regs[RMI_F30_CTRL_REGS_MAX_SIZE];
+	u32 ctrl_regs_size;
+
+	u8 data_regs[RMI_F30_CTRL_MAX_BYTES];
+	u16 *gpioled_key_map;
+
+	struct input_dev *input;
+};
+
+static int rmi_f30_read_control_parameters(struct rmi_function *fn,
+						struct f30_data *f30)
+{
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	int error = 0;
+
+	error = rmi_read_block(rmi_dev, fn->fd.control_base_addr,
+				f30->ctrl_regs, f30->ctrl_regs_size);
+	if (error) {
+		dev_err(&rmi_dev->dev, "%s : Could not read control registers at 0x%x error (%d)\n",
+			__func__, fn->fd.control_base_addr, error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int rmi_f30_attention(struct rmi_function *fn, unsigned long *irq_bits)
+{
+	struct f30_data *f30 = dev_get_drvdata(&fn->dev);
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	int retval;
+	int gpiled = 0;
+	int value = 0;
+	int i;
+	int reg_num;
+
+	if (!f30->input)
+		return 0;
+
+	/* Read the gpi led data. */
+	if (rmi_dev->xport->attn_data) {
+		memcpy(f30->data_regs, rmi_dev->xport->attn_data,
+			f30->register_count);
+		rmi_dev->xport->attn_data += f30->register_count;
+		rmi_dev->xport->attn_size -= f30->register_count;
+	} else {
+		retval = rmi_read_block(rmi_dev, fn->fd.data_base_addr,
+			f30->data_regs, f30->register_count);
+
+		if (retval) {
+			dev_err(&fn->dev, "%s: Failed to read F30 data registers.\n",
+				__func__);
+			return retval;
+		}
+	}
+
+	for (reg_num = 0; reg_num < f30->register_count; ++reg_num) {
+		for (i = 0; gpiled < f30->gpioled_count && i < 8; ++i,
+			++gpiled) {
+			if (f30->gpioled_key_map[gpiled] != 0) {
+				/* buttons have pull up resistors */
+				value = (((f30->data_regs[reg_num] >> i) & 0x01)
+									== 0);
+
+				rmi_dbg(RMI_DEBUG_FN, &fn->dev,
+					"%s: call input report key (0x%04x) value (0x%02x)",
+					__func__,
+					f30->gpioled_key_map[gpiled], value);
+				input_report_key(f30->input,
+						 f30->gpioled_key_map[gpiled],
+						 value);
+			}
+
+		}
+	}
+
+	return 0;
+}
+
+static int rmi_f30_register_device(struct rmi_function *fn)
+{
+	int i;
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	struct rmi_driver_data *drv_data = dev_get_drvdata(&rmi_dev->dev);
+	struct f30_data *f30 = dev_get_drvdata(&fn->dev);
+	struct input_dev *input_dev;
+	int button_count = 0;
+
+	input_dev = drv_data->input;
+	if (!input_dev) {
+		dev_info(&fn->dev, "F30: no input device found, ignoring.\n");
+		return -EINVAL;
+	}
+
+	f30->input = input_dev;
+
+	set_bit(EV_KEY, input_dev->evbit);
+
+	input_dev->keycode = f30->gpioled_key_map;
+	input_dev->keycodesize = sizeof(u16);
+	input_dev->keycodemax = f30->gpioled_count;
+
+	for (i = 0; i < f30->gpioled_count; i++) {
+		if (f30->gpioled_key_map[i] != 0) {
+			input_set_capability(input_dev, EV_KEY,
+						f30->gpioled_key_map[i]);
+			button_count++;
+		}
+	}
+
+	if (button_count == 1)
+		__set_bit(INPUT_PROP_BUTTONPAD, input_dev->propbit);
+	return 0;
+}
+
+static int rmi_f30_config(struct rmi_function *fn)
+{
+	struct f30_data *f30 = dev_get_drvdata(&fn->dev);
+	struct rmi_driver *drv = fn->rmi_dev->driver;
+	const struct rmi_device_platform_data *pdata =
+				rmi_get_platform_data(fn->rmi_dev);
+	int error;
+
+	if (pdata->f30_data && pdata->f30_data->disable) {
+		drv->clear_irq_bits(fn->rmi_dev, fn->irq_mask);
+	} else {
+		/* Write Control Register values back to device */
+		error = rmi_write_block(fn->rmi_dev, fn->fd.control_base_addr,
+					f30->ctrl_regs, f30->ctrl_regs_size);
+		if (error) {
+			dev_err(&fn->rmi_dev->dev,
+				"%s : Could not write control registers at 0x%x error (%d)\n",
+				__func__, fn->fd.control_base_addr, error);
+			return error;
+		}
+
+		drv->set_irq_bits(fn->rmi_dev, fn->irq_mask);
+	}
+	return 0;
+}
+
+static inline void rmi_f30_set_ctrl_data(struct rmi_f30_ctrl_data *ctrl,
+					int *ctrl_addr, int len, u8 **reg)
+{
+	ctrl->address = *ctrl_addr;
+	ctrl->length = len;
+	ctrl->regs = *reg;
+	*ctrl_addr += len;
+	*reg += len;
+}
+
+static inline bool rmi_f30_is_valid_button(int button,
+		struct rmi_f30_ctrl_data *ctrl)
+{
+	int byte_position = button >> 3;
+	int bit_position = button & 0x07;
+
+	/*
+	 * ctrl2 -> dir == 0 -> input mode
+	 * ctrl3 -> data == 1 -> actual button
+	 */
+	return !(ctrl[2].regs[byte_position] & BIT(bit_position)) &&
+		(ctrl[3].regs[byte_position] & BIT(bit_position));
+}
+
+static inline int rmi_f30_initialize(struct rmi_function *fn)
+{
+	struct f30_data *f30;
+	struct rmi_device *rmi_dev = fn->rmi_dev;
+	const struct rmi_device_platform_data *pdata;
+	int retval = 0;
+	int control_address;
+	int i;
+	int button;
+	u8 buf[RMI_F30_QUERY_SIZE];
+	u8 *ctrl_reg;
+	u8 *map_memory;
+
+	f30 = devm_kzalloc(&fn->dev, sizeof(struct f30_data),
+			   GFP_KERNEL);
+	if (!f30)
+		return -ENOMEM;
+
+	dev_set_drvdata(&fn->dev, f30);
+
+	retval = rmi_read_block(fn->rmi_dev, fn->fd.query_base_addr, buf,
+				RMI_F30_QUERY_SIZE);
+
+	if (retval) {
+		dev_err(&fn->dev, "Failed to read query register.\n");
+		return retval;
+	}
+
+	f30->has_extended_pattern = buf[0] & RMI_F30_EXTENDED_PATTERNS;
+	f30->has_mappable_buttons = buf[0] & RMI_F30_HAS_MAPPABLE_BUTTONS;
+	f30->has_led = buf[0] & RMI_F30_HAS_LED;
+	f30->has_gpio = buf[0] & RMI_F30_HAS_GPIO;
+	f30->has_haptic = buf[0] & RMI_F30_HAS_HAPTIC;
+	f30->has_gpio_driver_control = buf[0] & RMI_F30_HAS_GPIO_DRV_CTL;
+	f30->has_mech_mouse_btns = buf[0] & RMI_F30_HAS_MECH_MOUSE_BTNS;
+	f30->gpioled_count = buf[1] & RMI_F30_GPIO_LED_COUNT;
+
+	f30->register_count = (f30->gpioled_count + 7) >> 3;
+
+	control_address = fn->fd.control_base_addr;
+	ctrl_reg = f30->ctrl_regs;
+
+	if (f30->has_gpio && f30->has_led)
+		rmi_f30_set_ctrl_data(&f30->ctrl[0], &control_address,
+					f30->register_count, &ctrl_reg);
+
+	rmi_f30_set_ctrl_data(&f30->ctrl[1], &control_address, sizeof(u8),
+				&ctrl_reg);
+
+	if (f30->has_gpio) {
+		rmi_f30_set_ctrl_data(&f30->ctrl[2], &control_address,
+					f30->register_count, &ctrl_reg);
+
+		rmi_f30_set_ctrl_data(&f30->ctrl[3], &control_address,
+					f30->register_count, &ctrl_reg);
+	}
+
+	if (f30->has_led) {
+		int ctrl5_len;
+
+		rmi_f30_set_ctrl_data(&f30->ctrl[4], &control_address,
+					f30->register_count, &ctrl_reg);
+
+		if (f30->has_extended_pattern)
+			ctrl5_len = 6;
+		else
+			ctrl5_len = 2;
+
+		rmi_f30_set_ctrl_data(&f30->ctrl[5], &control_address,
+					ctrl5_len, &ctrl_reg);
+	}
+
+	if (f30->has_led || f30->has_gpio_driver_control) {
+		/* control 6 uses a byte per gpio/led */
+		rmi_f30_set_ctrl_data(&f30->ctrl[6], &control_address,
+					f30->gpioled_count, &ctrl_reg);
+	}
+
+	if (f30->has_mappable_buttons) {
+		/* control 7 uses a byte per gpio/led */
+		rmi_f30_set_ctrl_data(&f30->ctrl[7], &control_address,
+					f30->gpioled_count, &ctrl_reg);
+	}
+
+	if (f30->has_haptic) {
+		rmi_f30_set_ctrl_data(&f30->ctrl[8], &control_address,
+					f30->register_count, &ctrl_reg);
+
+		rmi_f30_set_ctrl_data(&f30->ctrl[9], &control_address,
+					sizeof(u8), &ctrl_reg);
+	}
+
+	if (f30->has_mech_mouse_btns)
+		rmi_f30_set_ctrl_data(&f30->ctrl[10], &control_address,
+					sizeof(u8), &ctrl_reg);
+
+	f30->ctrl_regs_size = ctrl_reg - f30->ctrl_regs
+				?: RMI_F30_CTRL_REGS_MAX_SIZE;
+
+	retval = rmi_f30_read_control_parameters(fn, f30);
+	if (retval < 0) {
+		dev_err(&fn->dev,
+			"Failed to initialize F19 control params.\n");
+		return retval;
+	}
+
+	map_memory = devm_kzalloc(&fn->dev,
+				  (f30->gpioled_count * (sizeof(u16))),
+				  GFP_KERNEL);
+	if (!map_memory) {
+		dev_err(&fn->dev, "Failed to allocate gpioled map memory.\n");
+		return -ENOMEM;
+	}
+
+	f30->gpioled_key_map = (u16 *)map_memory;
+
+	pdata = rmi_get_platform_data(rmi_dev);
+	if (pdata && f30->has_gpio) {
+		button = BTN_LEFT;
+		for (i = 0; i < f30->gpioled_count; i++) {
+			if (rmi_f30_is_valid_button(i, f30->ctrl)) {
+				f30->gpioled_key_map[i] = button++;
+
+				/*
+				 * buttonpad might be given by
+				 * f30->has_mech_mouse_btns, but I am
+				 * not sure, so use only the pdata info
+				 */
+				if (pdata->f30_data &&
+				    pdata->f30_data->buttonpad)
+					break;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static int rmi_f30_probe(struct rmi_function *fn)
+{
+	int rc;
+	const struct rmi_device_platform_data *pdata =
+				rmi_get_platform_data(fn->rmi_dev);
+
+	if (pdata->f30_data && pdata->f30_data->disable)
+		return 0;
+
+	rc = rmi_f30_initialize(fn);
+	if (rc < 0)
+		goto error_exit;
+
+	rc = rmi_f30_register_device(fn);
+	if (rc < 0)
+		goto error_exit;
+
+	return 0;
+
+error_exit:
+	return rc;
+
+}
+
+struct rmi_function_handler rmi_f30_handler = {
+	.driver = {
+		.name = "rmi4_f30",
+	},
+	.func = 0x30,
+	.probe = rmi_f30_probe,
+	.config = rmi_f30_config,
+	.attention = rmi_f30_attention,
+};

drivers/input/rmi4/rmi_i2c.c

@@ -0,0 +1,397 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/i2c.h>
+#include <linux/rmi.h>
+#include <linux/irq.h>
+#include <linux/of.h>
+#include "rmi_driver.h"
+
+#define BUFFER_SIZE_INCREMENT 32
+
+/**
+ * struct rmi_i2c_xport - stores information for i2c communication
+ *
+ * @xport: The transport interface structure
+ *
+ * @page_mutex: Locks current page to avoid changing pages in unexpected ways.
+ * @page: Keeps track of the current virtual page
+ *
+ * @tx_buf: Buffer used for transmitting data to the sensor over i2c.
+ * @tx_buf_size: Size of the buffer
+ */
+struct rmi_i2c_xport {
+	struct rmi_transport_dev xport;
+	struct i2c_client *client;
+
+	struct mutex page_mutex;
+	int page;
+
+	int irq;
+
+	u8 *tx_buf;
+	size_t tx_buf_size;
+};
+
+#define RMI_PAGE_SELECT_REGISTER 0xff
+#define RMI_I2C_PAGE(addr) (((addr) >> 8) & 0xff)
+
+/*
+ * rmi_set_page - Set RMI page
+ * @xport: The pointer to the rmi_transport_dev struct
+ * @page: The new page address.
+ *
+ * RMI devices have 16-bit addressing, but some of the transport
+ * implementations (like SMBus) only have 8-bit addressing. So RMI implements
+ * a page address at 0xff of every page so we can reliable page addresses
+ * every 256 registers.
+ *
+ * The page_mutex lock must be held when this function is entered.
+ *
+ * Returns zero on success, non-zero on failure.
+ */
+static int rmi_set_page(struct rmi_i2c_xport *rmi_i2c, u8 page)
+{
+	struct i2c_client *client = rmi_i2c->client;
+	u8 txbuf[2] = {RMI_PAGE_SELECT_REGISTER, page};
+	int retval;
+
+	retval = i2c_master_send(client, txbuf, sizeof(txbuf));
+	if (retval != sizeof(txbuf)) {
+		dev_err(&client->dev,
+			"%s: set page failed: %d.", __func__, retval);
+		return (retval < 0) ? retval : -EIO;
+	}
+
+	rmi_i2c->page = page;
+	return 0;
+}
+
+static int rmi_i2c_write_block(struct rmi_transport_dev *xport, u16 addr,
+			       const void *buf, size_t len)
+{
+	struct rmi_i2c_xport *rmi_i2c =
+		container_of(xport, struct rmi_i2c_xport, xport);
+	struct i2c_client *client = rmi_i2c->client;
+	size_t tx_size = len + 1;
+	int retval;
+
+	mutex_lock(&rmi_i2c->page_mutex);
+
+	if (!rmi_i2c->tx_buf || rmi_i2c->tx_buf_size < tx_size) {
+		if (rmi_i2c->tx_buf)
+			devm_kfree(&client->dev, rmi_i2c->tx_buf);
+		rmi_i2c->tx_buf_size = tx_size + BUFFER_SIZE_INCREMENT;
+		rmi_i2c->tx_buf = devm_kzalloc(&client->dev,
+					       rmi_i2c->tx_buf_size,
+					       GFP_KERNEL);
+		if (!rmi_i2c->tx_buf) {
+			rmi_i2c->tx_buf_size = 0;
+			retval = -ENOMEM;
+			goto exit;
+		}
+	}
+
+	rmi_i2c->tx_buf[0] = addr & 0xff;
+	memcpy(rmi_i2c->tx_buf + 1, buf, len);
+
+	if (RMI_I2C_PAGE(addr) != rmi_i2c->page) {
+		retval = rmi_set_page(rmi_i2c, RMI_I2C_PAGE(addr));
+		if (retval)
+			goto exit;
+	}
+
+	retval = i2c_master_send(client, rmi_i2c->tx_buf, tx_size);
+	if (retval == tx_size)
+		retval = 0;
+	else if (retval >= 0)
+		retval = -EIO;
+
+exit:
+	rmi_dbg(RMI_DEBUG_XPORT, &client->dev,
+		"write %zd bytes at %#06x: %d (%*ph)\n",
+		len, addr, retval, (int)len, buf);
+
+	mutex_unlock(&rmi_i2c->page_mutex);
+	return retval;
+}
+
+static int rmi_i2c_read_block(struct rmi_transport_dev *xport, u16 addr,
+			      void *buf, size_t len)
+{
+	struct rmi_i2c_xport *rmi_i2c =
+		container_of(xport, struct rmi_i2c_xport, xport);
+	struct i2c_client *client = rmi_i2c->client;
+	u8 addr_offset = addr & 0xff;
+	int retval;
+	struct i2c_msg msgs[] = {
+		{
+			.addr	= client->addr,
+			.len	= sizeof(addr_offset),
+			.buf	= &addr_offset,
+		},
+		{
+			.addr	= client->addr,
+			.flags	= I2C_M_RD,
+			.len	= len,
+			.buf	= buf,
+		},
+	};
+
+	mutex_lock(&rmi_i2c->page_mutex);
+
+	if (RMI_I2C_PAGE(addr) != rmi_i2c->page) {
+		retval = rmi_set_page(rmi_i2c, RMI_I2C_PAGE(addr));
+		if (retval)
+			goto exit;
+	}
+
+	retval = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (retval == ARRAY_SIZE(msgs))
+		retval = 0; /* success */
+	else if (retval >= 0)
+		retval = -EIO;
+
+exit:
+	rmi_dbg(RMI_DEBUG_XPORT, &client->dev,
+		"read %zd bytes at %#06x: %d (%*ph)\n",
+		len, addr, retval, (int)len, buf);
+
+	mutex_unlock(&rmi_i2c->page_mutex);
+	return retval;
+}
+
+static const struct rmi_transport_ops rmi_i2c_ops = {
+	.write_block	= rmi_i2c_write_block,
+	.read_block	= rmi_i2c_read_block,
+};
+
+static irqreturn_t rmi_i2c_irq(int irq, void *dev_id)
+{
+	struct rmi_i2c_xport *rmi_i2c = dev_id;
+	struct rmi_device *rmi_dev = rmi_i2c->xport.rmi_dev;
+	int ret;
+
+	ret = rmi_process_interrupt_requests(rmi_dev);
+	if (ret)
+		rmi_dbg(RMI_DEBUG_XPORT, &rmi_dev->dev,
+			"Failed to process interrupt request: %d\n", ret);
+
+	return IRQ_HANDLED;
+}
+
+static int rmi_i2c_init_irq(struct i2c_client *client)
+{
+	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
+	int irq_flags = irqd_get_trigger_type(irq_get_irq_data(rmi_i2c->irq));
+	int ret;
+
+	if (!irq_flags)
+		irq_flags = IRQF_TRIGGER_LOW;
+
+	ret = devm_request_threaded_irq(&client->dev, rmi_i2c->irq, NULL,
+			rmi_i2c_irq, irq_flags | IRQF_ONESHOT, client->name,
+			rmi_i2c);
+	if (ret < 0) {
+		dev_warn(&client->dev, "Failed to register interrupt %d\n",
+			rmi_i2c->irq);
+
+		return ret;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id rmi_i2c_of_match[] = {
+	{ .compatible = "syna,rmi4-i2c" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, rmi_i2c_of_match);
+#endif
+
+static int rmi_i2c_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct rmi_device_platform_data *pdata;
+	struct rmi_device_platform_data *client_pdata =
+					dev_get_platdata(&client->dev);
+	struct rmi_i2c_xport *rmi_i2c;
+	int retval;
+
+	rmi_i2c = devm_kzalloc(&client->dev, sizeof(struct rmi_i2c_xport),
+				GFP_KERNEL);
+	if (!rmi_i2c)
+		return -ENOMEM;
+
+	pdata = &rmi_i2c->xport.pdata;
+
+	if (!client->dev.of_node && client_pdata)
+		*pdata = *client_pdata;
+
+	if (client->irq > 0)
+		rmi_i2c->irq = client->irq;
+
+	rmi_dbg(RMI_DEBUG_XPORT, &client->dev, "Probing %s.\n",
+			dev_name(&client->dev));
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev,
+			"adapter does not support required functionality.\n");
+		return -ENODEV;
+	}
+
+	rmi_i2c->client = client;
+	mutex_init(&rmi_i2c->page_mutex);
+
+	rmi_i2c->xport.dev = &client->dev;
+	rmi_i2c->xport.proto_name = "i2c";
+	rmi_i2c->xport.ops = &rmi_i2c_ops;
+
+	i2c_set_clientdata(client, rmi_i2c);
+
+	/*
+	 * Setting the page to zero will (a) make sure the PSR is in a
+	 * known state, and (b) make sure we can talk to the device.
+	 */
+	retval = rmi_set_page(rmi_i2c, 0);
+	if (retval) {
+		dev_err(&client->dev, "Failed to set page select to 0.\n");
+		return retval;
+	}
+
+	retval = rmi_register_transport_device(&rmi_i2c->xport);
+	if (retval) {
+		dev_err(&client->dev, "Failed to register transport driver at 0x%.2X.\n",
+			client->addr);
+		return retval;
+	}
+
+	retval = rmi_i2c_init_irq(client);
+	if (retval < 0)
+		return retval;
+
+	dev_info(&client->dev, "registered rmi i2c driver at %#04x.\n",
+			client->addr);
+	return 0;
+}
+
+static int rmi_i2c_remove(struct i2c_client *client)
+{
+	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
+
+	rmi_unregister_transport_device(&rmi_i2c->xport);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int rmi_i2c_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
+	int ret;
+
+	ret = rmi_driver_suspend(rmi_i2c->xport.rmi_dev);
+	if (ret)
+		dev_warn(dev, "Failed to resume device: %d\n", ret);
+
+	disable_irq(rmi_i2c->irq);
+	if (device_may_wakeup(&client->dev)) {
+		ret = enable_irq_wake(rmi_i2c->irq);
+		if (!ret)
+			dev_warn(dev, "Failed to enable irq for wake: %d\n",
+				ret);
+	}
+	return ret;
+}
+
+static int rmi_i2c_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
+	int ret;
+
+	enable_irq(rmi_i2c->irq);
+	if (device_may_wakeup(&client->dev)) {
+		ret = disable_irq_wake(rmi_i2c->irq);
+		if (!ret)
+			dev_warn(dev, "Failed to disable irq for wake: %d\n",
+				ret);
+	}
+
+	ret = rmi_driver_resume(rmi_i2c->xport.rmi_dev);
+	if (ret)
+		dev_warn(dev, "Failed to resume device: %d\n", ret);
+
+	return ret;
+}
+#endif
+
+#ifdef CONFIG_PM
+static int rmi_i2c_runtime_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
+	int ret;
+
+	ret = rmi_driver_suspend(rmi_i2c->xport.rmi_dev);
+	if (ret)
+		dev_warn(dev, "Failed to resume device: %d\n", ret);
+
+	disable_irq(rmi_i2c->irq);
+
+	return 0;
+}
+
+static int rmi_i2c_runtime_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
+	int ret;
+
+	enable_irq(rmi_i2c->irq);
+
+	ret = rmi_driver_resume(rmi_i2c->xport.rmi_dev);
+	if (ret)
+		dev_warn(dev, "Failed to resume device: %d\n", ret);
+
+	return 0;
+}
+#endif
+
+static const struct dev_pm_ops rmi_i2c_pm = {
+	SET_SYSTEM_SLEEP_PM_OPS(rmi_i2c_suspend, rmi_i2c_resume)
+	SET_RUNTIME_PM_OPS(rmi_i2c_runtime_suspend, rmi_i2c_runtime_resume,
+			   NULL)
+};
+
+static const struct i2c_device_id rmi_id[] = {
+	{ "rmi4_i2c", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, rmi_id);
+
+static struct i2c_driver rmi_i2c_driver = {
+	.driver = {
+		.name	= "rmi4_i2c",
+		.pm	= &rmi_i2c_pm,
+		.of_match_table = of_match_ptr(rmi_i2c_of_match),
+	},
+	.id_table	= rmi_id,
+	.probe		= rmi_i2c_probe,
+	.remove		= rmi_i2c_remove,
+};
+
+module_i2c_driver(rmi_i2c_driver);
+
+MODULE_AUTHOR("Christopher Heiny <cheiny@synaptics.com>");
+MODULE_AUTHOR("Andrew Duggan <aduggan@synaptics.com>");
+MODULE_DESCRIPTION("RMI I2C driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(RMI_DRIVER_VERSION);

drivers/input/rmi4/rmi_spi.c

@@ -0,0 +1,589 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/rmi.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/irq.h>
+#include <linux/of.h>
+#include "rmi_driver.h"
+
+#define RMI_SPI_DEFAULT_XFER_BUF_SIZE	64
+
+#define RMI_PAGE_SELECT_REGISTER	0x00FF
+#define RMI_SPI_PAGE(addr)		(((addr) >> 8) & 0x80)
+#define RMI_SPI_XFER_SIZE_LIMIT		255
+
+#define BUFFER_SIZE_INCREMENT 32
+
+enum rmi_spi_op {
+	RMI_SPI_WRITE = 0,
+	RMI_SPI_READ,
+	RMI_SPI_V2_READ_UNIFIED,
+	RMI_SPI_V2_READ_SPLIT,
+	RMI_SPI_V2_WRITE,
+};
+
+struct rmi_spi_cmd {
+	enum rmi_spi_op op;
+	u16 addr;
+};
+
+struct rmi_spi_xport {
+	struct rmi_transport_dev xport;
+	struct spi_device *spi;
+
+	struct mutex page_mutex;
+	int page;
+
+	int irq;
+
+	u8 *rx_buf;
+	u8 *tx_buf;
+	int xfer_buf_size;
+
+	struct spi_transfer *rx_xfers;
+	struct spi_transfer *tx_xfers;
+	int rx_xfer_count;
+	int tx_xfer_count;
+};
+
+static int rmi_spi_manage_pools(struct rmi_spi_xport *rmi_spi, int len)
+{
+	struct spi_device *spi = rmi_spi->spi;
+	int buf_size = rmi_spi->xfer_buf_size
+		? rmi_spi->xfer_buf_size : RMI_SPI_DEFAULT_XFER_BUF_SIZE;
+	struct spi_transfer *xfer_buf;
+	void *buf;
+	void *tmp;
+
+	while (buf_size < len)
+		buf_size *= 2;
+
+	if (buf_size > RMI_SPI_XFER_SIZE_LIMIT)
+		buf_size = RMI_SPI_XFER_SIZE_LIMIT;
+
+	tmp = rmi_spi->rx_buf;
+	buf = devm_kzalloc(&spi->dev, buf_size * 2,
+				GFP_KERNEL | GFP_DMA);
+	if (!buf)
+		return -ENOMEM;
+
+	rmi_spi->rx_buf = buf;
+	rmi_spi->tx_buf = &rmi_spi->rx_buf[buf_size];
+	rmi_spi->xfer_buf_size = buf_size;
+
+	if (tmp)
+		devm_kfree(&spi->dev, tmp);
+
+	if (rmi_spi->xport.pdata.spi_data.read_delay_us)
+		rmi_spi->rx_xfer_count = buf_size;
+	else
+		rmi_spi->rx_xfer_count = 1;
+
+	if (rmi_spi->xport.pdata.spi_data.write_delay_us)
+		rmi_spi->tx_xfer_count = buf_size;
+	else
+		rmi_spi->tx_xfer_count = 1;
+
+	/*
+	 * Allocate a pool of spi_transfer buffers for devices which need
+	 * per byte delays.
+	 */
+	tmp = rmi_spi->rx_xfers;
+	xfer_buf = devm_kzalloc(&spi->dev,
+		(rmi_spi->rx_xfer_count + rmi_spi->tx_xfer_count)
+		* sizeof(struct spi_transfer), GFP_KERNEL);
+	if (!xfer_buf)
+		return -ENOMEM;
+
+	rmi_spi->rx_xfers = xfer_buf;
+	rmi_spi->tx_xfers = &xfer_buf[rmi_spi->rx_xfer_count];
+
+	if (tmp)
+		devm_kfree(&spi->dev, tmp);
+
+	return 0;
+}
+
+static int rmi_spi_xfer(struct rmi_spi_xport *rmi_spi,
+			const struct rmi_spi_cmd *cmd, const u8 *tx_buf,
+			int tx_len, u8 *rx_buf, int rx_len)
+{
+	struct spi_device *spi = rmi_spi->spi;
+	struct rmi_device_platform_data_spi *spi_data =
+					&rmi_spi->xport.pdata.spi_data;
+	struct spi_message msg;
+	struct spi_transfer *xfer;
+	int ret = 0;
+	int len;
+	int cmd_len = 0;
+	int total_tx_len;
+	int i;
+	u16 addr = cmd->addr;
+
+	spi_message_init(&msg);
+
+	switch (cmd->op) {
+	case RMI_SPI_WRITE:
+	case RMI_SPI_READ:
+		cmd_len += 2;
+		break;
+	case RMI_SPI_V2_READ_UNIFIED:
+	case RMI_SPI_V2_READ_SPLIT:
+	case RMI_SPI_V2_WRITE:
+		cmd_len += 4;
+		break;
+	}
+
+	total_tx_len = cmd_len + tx_len;
+	len = max(total_tx_len, rx_len);
+
+	if (len > RMI_SPI_XFER_SIZE_LIMIT)
+		return -EINVAL;
+
+	if (rmi_spi->xfer_buf_size < len)
+		rmi_spi_manage_pools(rmi_spi, len);
+
+	if (addr == 0)
+		/*
+		 * SPI needs an address. Use 0x7FF if we want to keep
+		 * reading from the last position of the register pointer.
+		 */
+		addr = 0x7FF;
+
+	switch (cmd->op) {
+	case RMI_SPI_WRITE:
+		rmi_spi->tx_buf[0] = (addr >> 8);
+		rmi_spi->tx_buf[1] = addr & 0xFF;
+		break;
+	case RMI_SPI_READ:
+		rmi_spi->tx_buf[0] = (addr >> 8) | 0x80;
+		rmi_spi->tx_buf[1] = addr & 0xFF;
+		break;
+	case RMI_SPI_V2_READ_UNIFIED:
+		break;
+	case RMI_SPI_V2_READ_SPLIT:
+		break;
+	case RMI_SPI_V2_WRITE:
+		rmi_spi->tx_buf[0] = 0x40;
+		rmi_spi->tx_buf[1] = (addr >> 8) & 0xFF;
+		rmi_spi->tx_buf[2] = addr & 0xFF;
+		rmi_spi->tx_buf[3] = tx_len;
+		break;
+	}
+
+	if (tx_buf)
+		memcpy(&rmi_spi->tx_buf[cmd_len], tx_buf, tx_len);
+
+	if (rmi_spi->tx_xfer_count > 1) {
+		for (i = 0; i < total_tx_len; i++) {
+			xfer = &rmi_spi->tx_xfers[i];
+			memset(xfer, 0,	sizeof(struct spi_transfer));
+			xfer->tx_buf = &rmi_spi->tx_buf[i];
+			xfer->len = 1;
+			xfer->delay_usecs = spi_data->write_delay_us;
+			spi_message_add_tail(xfer, &msg);
+		}
+	} else {
+		xfer = rmi_spi->tx_xfers;
+		memset(xfer, 0, sizeof(struct spi_transfer));
+		xfer->tx_buf = rmi_spi->tx_buf;
+		xfer->len = total_tx_len;
+		spi_message_add_tail(xfer, &msg);
+	}
+
+	rmi_dbg(RMI_DEBUG_XPORT, &spi->dev, "%s: cmd: %s tx_buf len: %d tx_buf: %*ph\n",
+		__func__, cmd->op == RMI_SPI_WRITE ? "WRITE" : "READ",
+		total_tx_len, total_tx_len, rmi_spi->tx_buf);
+
+	if (rx_buf) {
+		if (rmi_spi->rx_xfer_count > 1) {
+			for (i = 0; i < rx_len; i++) {
+				xfer = &rmi_spi->rx_xfers[i];
+				memset(xfer, 0, sizeof(struct spi_transfer));
+				xfer->rx_buf = &rmi_spi->rx_buf[i];
+				xfer->len = 1;
+				xfer->delay_usecs = spi_data->read_delay_us;
+				spi_message_add_tail(xfer, &msg);
+			}
+		} else {
+			xfer = rmi_spi->rx_xfers;
+			memset(xfer, 0, sizeof(struct spi_transfer));
+			xfer->rx_buf = rmi_spi->rx_buf;
+			xfer->len = rx_len;
+			spi_message_add_tail(xfer, &msg);
+		}
+	}
+
+	ret = spi_sync(spi, &msg);
+	if (ret < 0) {
+		dev_err(&spi->dev, "spi xfer failed: %d\n", ret);
+		return ret;
+	}
+
+	if (rx_buf) {
+		memcpy(rx_buf, rmi_spi->rx_buf, rx_len);
+		rmi_dbg(RMI_DEBUG_XPORT, &spi->dev, "%s: (%d) %*ph\n",
+			__func__, rx_len, rx_len, rx_buf);
+	}
+
+	return 0;
+}
+
+/*
+ * rmi_set_page - Set RMI page
+ * @xport: The pointer to the rmi_transport_dev struct
+ * @page: The new page address.
+ *
+ * RMI devices have 16-bit addressing, but some of the transport
+ * implementations (like SMBus) only have 8-bit addressing. So RMI implements
+ * a page address at 0xff of every page so we can reliable page addresses
+ * every 256 registers.
+ *
+ * The page_mutex lock must be held when this function is entered.
+ *
+ * Returns zero on success, non-zero on failure.
+ */
+static int rmi_set_page(struct rmi_spi_xport *rmi_spi, u8 page)
+{
+	struct rmi_spi_cmd cmd;
+	int ret;
+
+	cmd.op = RMI_SPI_WRITE;
+	cmd.addr = RMI_PAGE_SELECT_REGISTER;
+
+	ret = rmi_spi_xfer(rmi_spi, &cmd, &page, 1, NULL, 0);
+
+	if (ret)
+		rmi_spi->page = page;
+
+	return ret;
+}
+
+static int rmi_spi_write_block(struct rmi_transport_dev *xport, u16 addr,
+			       const void *buf, size_t len)
+{
+	struct rmi_spi_xport *rmi_spi =
+		container_of(xport, struct rmi_spi_xport, xport);
+	struct rmi_spi_cmd cmd;
+	int ret;
+
+	mutex_lock(&rmi_spi->page_mutex);
+
+	if (RMI_SPI_PAGE(addr) != rmi_spi->page) {
+		ret = rmi_set_page(rmi_spi, RMI_SPI_PAGE(addr));
+		if (ret)
+			goto exit;
+	}
+
+	cmd.op = RMI_SPI_WRITE;
+	cmd.addr = addr;
+
+	ret = rmi_spi_xfer(rmi_spi, &cmd, buf, len, NULL, 0);
+
+exit:
+	mutex_unlock(&rmi_spi->page_mutex);
+	return ret;
+}
+
+static int rmi_spi_read_block(struct rmi_transport_dev *xport, u16 addr,
+			      void *buf, size_t len)
+{
+	struct rmi_spi_xport *rmi_spi =
+		container_of(xport, struct rmi_spi_xport, xport);
+	struct rmi_spi_cmd cmd;
+	int ret;
+
+	mutex_lock(&rmi_spi->page_mutex);
+
+	if (RMI_SPI_PAGE(addr) != rmi_spi->page) {
+		ret = rmi_set_page(rmi_spi, RMI_SPI_PAGE(addr));
+		if (ret)
+			goto exit;
+	}
+
+	cmd.op = RMI_SPI_READ;
+	cmd.addr = addr;
+
+	ret = rmi_spi_xfer(rmi_spi, &cmd, NULL, 0, buf, len);
+
+exit:
+	mutex_unlock(&rmi_spi->page_mutex);
+	return ret;
+}
+
+static const struct rmi_transport_ops rmi_spi_ops = {
+	.write_block	= rmi_spi_write_block,
+	.read_block	= rmi_spi_read_block,
+};
+
+static irqreturn_t rmi_spi_irq(int irq, void *dev_id)
+{
+	struct rmi_spi_xport *rmi_spi = dev_id;
+	struct rmi_device *rmi_dev = rmi_spi->xport.rmi_dev;
+	int ret;
+
+	ret = rmi_process_interrupt_requests(rmi_dev);
+	if (ret)
+		rmi_dbg(RMI_DEBUG_XPORT, &rmi_dev->dev,
+			"Failed to process interrupt request: %d\n", ret);
+
+	return IRQ_HANDLED;
+}
+
+static int rmi_spi_init_irq(struct spi_device *spi)
+{
+	struct rmi_spi_xport *rmi_spi = spi_get_drvdata(spi);
+	int irq_flags = irqd_get_trigger_type(irq_get_irq_data(rmi_spi->irq));
+	int ret;
+
+	if (!irq_flags)
+		irq_flags = IRQF_TRIGGER_LOW;
+
+	ret = devm_request_threaded_irq(&spi->dev, rmi_spi->irq, NULL,
+			rmi_spi_irq, irq_flags | IRQF_ONESHOT,
+			dev_name(&spi->dev), rmi_spi);
+	if (ret < 0) {
+		dev_warn(&spi->dev, "Failed to register interrupt %d\n",
+			rmi_spi->irq);
+		return ret;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static int rmi_spi_of_probe(struct spi_device *spi,
+			struct rmi_device_platform_data *pdata)
+{
+	struct device *dev = &spi->dev;
+	int retval;
+
+	retval = rmi_of_property_read_u32(dev,
+			&pdata->spi_data.read_delay_us,
+			"spi-rx-delay-us", 1);
+	if (retval)
+		return retval;
+
+	retval = rmi_of_property_read_u32(dev,
+			&pdata->spi_data.write_delay_us,
+			"spi-tx-delay-us", 1);
+	if (retval)
+		return retval;
+
+	return 0;
+}
+
+static const struct of_device_id rmi_spi_of_match[] = {
+	{ .compatible = "syna,rmi4-spi" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, rmi_spi_of_match);
+#else
+static inline int rmi_spi_of_probe(struct spi_device *spi,
+				struct rmi_device_platform_data *pdata)
+{
+	return -ENODEV;
+}
+#endif
+
+static int rmi_spi_probe(struct spi_device *spi)
+{
+	struct rmi_spi_xport *rmi_spi;
+	struct rmi_device_platform_data *pdata;
+	struct rmi_device_platform_data *spi_pdata = spi->dev.platform_data;
+	int retval;
+
+	if (spi->master->flags & SPI_MASTER_HALF_DUPLEX)
+		return -EINVAL;
+
+	rmi_spi = devm_kzalloc(&spi->dev, sizeof(struct rmi_spi_xport),
+			GFP_KERNEL);
+	if (!rmi_spi)
+		return -ENOMEM;
+
+	pdata = &rmi_spi->xport.pdata;
+
+	if (spi->dev.of_node) {
+		retval = rmi_spi_of_probe(spi, pdata);
+		if (retval)
+			return retval;
+	} else if (spi_pdata) {
+		*pdata = *spi_pdata;
+	}
+
+	if (pdata->spi_data.bits_per_word)
+		spi->bits_per_word = pdata->spi_data.bits_per_word;
+
+	if (pdata->spi_data.mode)
+		spi->mode = pdata->spi_data.mode;
+
+	retval = spi_setup(spi);
+	if (retval < 0) {
+		dev_err(&spi->dev, "spi_setup failed!\n");
+		return retval;
+	}
+
+	if (spi->irq > 0)
+		rmi_spi->irq = spi->irq;
+
+	rmi_spi->spi = spi;
+	mutex_init(&rmi_spi->page_mutex);
+
+	rmi_spi->xport.dev = &spi->dev;
+	rmi_spi->xport.proto_name = "spi";
+	rmi_spi->xport.ops = &rmi_spi_ops;
+
+	spi_set_drvdata(spi, rmi_spi);
+
+	retval = rmi_spi_manage_pools(rmi_spi, RMI_SPI_DEFAULT_XFER_BUF_SIZE);
+	if (retval)
+		return retval;
+
+	/*
+	 * Setting the page to zero will (a) make sure the PSR is in a
+	 * known state, and (b) make sure we can talk to the device.
+	 */
+	retval = rmi_set_page(rmi_spi, 0);
+	if (retval) {
+		dev_err(&spi->dev, "Failed to set page select to 0.\n");
+		return retval;
+	}
+
+	retval = rmi_register_transport_device(&rmi_spi->xport);
+	if (retval) {
+		dev_err(&spi->dev, "failed to register transport.\n");
+		return retval;
+	}
+
+	retval = rmi_spi_init_irq(spi);
+	if (retval < 0)
+		return retval;
+
+	dev_info(&spi->dev, "registered RMI SPI driver\n");
+	return 0;
+}
+
+static int rmi_spi_remove(struct spi_device *spi)
+{
+	struct rmi_spi_xport *rmi_spi = spi_get_drvdata(spi);
+
+	rmi_unregister_transport_device(&rmi_spi->xport);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int rmi_spi_suspend(struct device *dev)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct rmi_spi_xport *rmi_spi = spi_get_drvdata(spi);
+	int ret;
+
+	ret = rmi_driver_suspend(rmi_spi->xport.rmi_dev);
+	if (ret)
+		dev_warn(dev, "Failed to resume device: %d\n", ret);
+
+	disable_irq(rmi_spi->irq);
+	if (device_may_wakeup(&spi->dev)) {
+		ret = enable_irq_wake(rmi_spi->irq);
+		if (!ret)
+			dev_warn(dev, "Failed to enable irq for wake: %d\n",
+				ret);
+	}
+	return ret;
+}
+
+static int rmi_spi_resume(struct device *dev)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct rmi_spi_xport *rmi_spi = spi_get_drvdata(spi);
+	int ret;
+
+	enable_irq(rmi_spi->irq);
+	if (device_may_wakeup(&spi->dev)) {
+		ret = disable_irq_wake(rmi_spi->irq);
+		if (!ret)
+			dev_warn(dev, "Failed to disable irq for wake: %d\n",
+				ret);
+	}
+
+	ret = rmi_driver_resume(rmi_spi->xport.rmi_dev);
+	if (ret)
+		dev_warn(dev, "Failed to resume device: %d\n", ret);
+
+	return ret;
+}
+#endif
+
+#ifdef CONFIG_PM
+static int rmi_spi_runtime_suspend(struct device *dev)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct rmi_spi_xport *rmi_spi = spi_get_drvdata(spi);
+	int ret;
+
+	ret = rmi_driver_suspend(rmi_spi->xport.rmi_dev);
+	if (ret)
+		dev_warn(dev, "Failed to resume device: %d\n", ret);
+
+	disable_irq(rmi_spi->irq);
+
+	return 0;
+}
+
+static int rmi_spi_runtime_resume(struct device *dev)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct rmi_spi_xport *rmi_spi = spi_get_drvdata(spi);
+	int ret;
+
+	enable_irq(rmi_spi->irq);
+
+	ret = rmi_driver_resume(rmi_spi->xport.rmi_dev);
+	if (ret)
+		dev_warn(dev, "Failed to resume device: %d\n", ret);
+
+	return 0;
+}
+#endif
+
+static const struct dev_pm_ops rmi_spi_pm = {
+	SET_SYSTEM_SLEEP_PM_OPS(rmi_spi_suspend, rmi_spi_resume)
+	SET_RUNTIME_PM_OPS(rmi_spi_runtime_suspend, rmi_spi_runtime_resume,
+			   NULL)
+};
+
+static const struct spi_device_id rmi_id[] = {
+	{ "rmi4_spi", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, rmi_id);
+
+static struct spi_driver rmi_spi_driver = {
+	.driver = {
+		.name	= "rmi4_spi",
+		.pm	= &rmi_spi_pm,
+		.of_match_table = of_match_ptr(rmi_spi_of_match),
+	},
+	.id_table	= rmi_id,
+	.probe		= rmi_spi_probe,
+	.remove		= rmi_spi_remove,
+};
+
+module_spi_driver(rmi_spi_driver);
+
+MODULE_AUTHOR("Christopher Heiny <cheiny@synaptics.com>");
+MODULE_AUTHOR("Andrew Duggan <aduggan@synaptics.com>");
+MODULE_DESCRIPTION("RMI SPI driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(RMI_DRIVER_VERSION);

include/linux/rmi.h

@@ -0,0 +1,359 @@
+/*
+ * Copyright (c) 2011-2016 Synaptics Incorporated
+ * Copyright (c) 2011 Unixphere
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#ifndef _RMI_H
+#define _RMI_H
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/types.h>
+
+#define NAME_BUFFER_SIZE 256
+
+/**
+ * struct rmi_2d_axis_alignment - target axis alignment
+ * @swap_axes: set to TRUE if desired to swap x- and y-axis
+ * @flip_x: set to TRUE if desired to flip direction on x-axis
+ * @flip_y: set to TRUE if desired to flip direction on y-axis
+ * @clip_x_low - reported X coordinates below this setting will be clipped to
+ *               the specified value
+ * @clip_x_high - reported X coordinates above this setting will be clipped to
+ *               the specified value
+ * @clip_y_low - reported Y coordinates below this setting will be clipped to
+ *               the specified value
+ * @clip_y_high - reported Y coordinates above this setting will be clipped to
+ *               the specified value
+ * @offset_x - this value will be added to all reported X coordinates
+ * @offset_y - this value will be added to all reported Y coordinates
+ * @rel_report_enabled - if set to true, the relative reporting will be
+ *               automatically enabled for this sensor.
+ */
+struct rmi_2d_axis_alignment {
+	bool swap_axes;
+	bool flip_x;
+	bool flip_y;
+	u16 clip_x_low;
+	u16 clip_y_low;
+	u16 clip_x_high;
+	u16 clip_y_high;
+	u16 offset_x;
+	u16 offset_y;
+	u8 delta_x_threshold;
+	u8 delta_y_threshold;
+};
+
+/** This is used to override any hints an F11 2D sensor might have provided
+ * as to what type of sensor it is.
+ *
+ * @rmi_f11_sensor_default - do not override, determine from F11_2D_QUERY14 if
+ * available.
+ * @rmi_f11_sensor_touchscreen - treat the sensor as a touchscreen (direct
+ * pointing).
+ * @rmi_f11_sensor_touchpad - thread the sensor as a touchpad (indirect
+ * pointing).
+ */
+enum rmi_sensor_type {
+	rmi_sensor_default = 0,
+	rmi_sensor_touchscreen,
+	rmi_sensor_touchpad
+};
+
+#define RMI_F11_DISABLE_ABS_REPORT      BIT(0)
+
+/**
+ * struct rmi_2d_sensor_data - overrides defaults for a 2D sensor.
+ * @axis_align - provides axis alignment overrides (see above).
+ * @sensor_type - Forces the driver to treat the sensor as an indirect
+ * pointing device (touchpad) rather than a direct pointing device
+ * (touchscreen).  This is useful when F11_2D_QUERY14 register is not
+ * available.
+ * @disable_report_mask - Force data to not be reported even if it is supported
+ * by the firware.
+ * @topbuttonpad - Used with the "5 buttons touchpads" found on the Lenovo 40
+ * series
+ * @kernel_tracking - most moderns RMI f11 firmwares implement Multifinger
+ * Type B protocol. However, there are some corner cases where the user
+ * triggers some jumps by tapping with two fingers on the touchpad.
+ * Use this setting and dmax to filter out these jumps.
+ * Also, when using an old sensor using MF Type A behavior, set to true to
+ * report an actual MT protocol B.
+ * @dmax - the maximum distance (in sensor units) the kernel tracking allows two
+ * distincts fingers to be considered the same.
+ */
+struct rmi_2d_sensor_platform_data {
+	struct rmi_2d_axis_alignment axis_align;
+	enum rmi_sensor_type sensor_type;
+	int x_mm;
+	int y_mm;
+	int disable_report_mask;
+	u16 rezero_wait;
+	bool topbuttonpad;
+	bool kernel_tracking;
+	int dmax;
+};
+
+/**
+ * struct rmi_f30_data - overrides defaults for a single F30 GPIOs/LED chip.
+ * @buttonpad - the touchpad is a buttonpad, so enable only the first actual
+ * button that is found.
+ * @trackstick_buttons - Set when the function 30 is handling the physical
+ * buttons of the trackstick (as a PD/2 passthrough device.
+ * @disable - the touchpad incorrectly reports F30 and it should be ignored.
+ * This is a special case which is due to misconfigured firmware.
+ */
+struct rmi_f30_data {
+	bool buttonpad;
+	bool trackstick_buttons;
+	bool disable;
+};
+
+/**
+ * struct rmi_f01_power - override default power management settings.
+ *
+ */
+enum rmi_f01_nosleep {
+	RMI_F01_NOSLEEP_DEFAULT = 0,
+	RMI_F01_NOSLEEP_OFF = 1,
+	RMI_F01_NOSLEEP_ON = 2
+};
+
+/**
+ * struct rmi_f01_power_management -When non-zero, these values will be written
+ * to the touch sensor to override the default firmware settigns.  For a
+ * detailed explanation of what each field does, see the corresponding
+ * documention in the RMI4 specification.
+ *
+ * @nosleep - specifies whether the device is permitted to sleep or doze (that
+ * is, enter a temporary low power state) when no fingers are touching the
+ * sensor.
+ * @wakeup_threshold - controls the capacitance threshold at which the touch
+ * sensor will decide to wake up from that low power state.
+ * @doze_holdoff - controls how long the touch sensor waits after the last
+ * finger lifts before entering the doze state, in units of 100ms.
+ * @doze_interval - controls the interval between checks for finger presence
+ * when the touch sensor is in doze mode, in units of 10ms.
+ */
+struct rmi_f01_power_management {
+	enum rmi_f01_nosleep nosleep;
+	u8 wakeup_threshold;
+	u8 doze_holdoff;
+	u8 doze_interval;
+};
+
+/**
+ * struct rmi_device_platform_data_spi - provides parameters used in SPI
+ * communications.  All Synaptics SPI products support a standard SPI
+ * interface; some also support what is called SPI V2 mode, depending on
+ * firmware and/or ASIC limitations.  In V2 mode, the touch sensor can
+ * support shorter delays during certain operations, and these are specified
+ * separately from the standard mode delays.
+ *
+ * @block_delay - for standard SPI transactions consisting of both a read and
+ * write operation, the delay (in microseconds) between the read and write
+ * operations.
+ * @split_read_block_delay_us - for V2 SPI transactions consisting of both a
+ * read and write operation, the delay (in microseconds) between the read and
+ * write operations.
+ * @read_delay_us - the delay between each byte of a read operation in normal
+ * SPI mode.
+ * @write_delay_us - the delay between each byte of a write operation in normal
+ * SPI mode.
+ * @split_read_byte_delay_us - the delay between each byte of a read operation
+ * in V2 mode.
+ * @pre_delay_us - the delay before the start of a SPI transaction.  This is
+ * typically useful in conjunction with custom chip select assertions (see
+ * below).
+ * @post_delay_us - the delay after the completion of an SPI transaction.  This
+ * is typically useful in conjunction with custom chip select assertions (see
+ * below).
+ * @cs_assert - For systems where the SPI subsystem does not control the CS/SSB
+ * line, or where such control is broken, you can provide a custom routine to
+ * handle a GPIO as CS/SSB.  This routine will be called at the beginning and
+ * end of each SPI transaction.  The RMI SPI implementation will wait
+ * pre_delay_us after this routine returns before starting the SPI transfer;
+ * and post_delay_us after completion of the SPI transfer(s) before calling it
+ * with assert==FALSE.
+ */
+struct rmi_device_platform_data_spi {
+	u32 block_delay_us;
+	u32 split_read_block_delay_us;
+	u32 read_delay_us;
+	u32 write_delay_us;
+	u32 split_read_byte_delay_us;
+	u32 pre_delay_us;
+	u32 post_delay_us;
+	u8 bits_per_word;
+	u16 mode;
+
+	void *cs_assert_data;
+	int (*cs_assert)(const void *cs_assert_data, const bool assert);
+};
+
+/**
+ * struct rmi_device_platform_data - system specific configuration info.
+ *
+ * @reset_delay_ms - after issuing a reset command to the touch sensor, the
+ * driver waits a few milliseconds to give the firmware a chance to
+ * to re-initialize.  You can override the default wait period here.
+ */
+struct rmi_device_platform_data {
+	int reset_delay_ms;
+
+	struct rmi_device_platform_data_spi spi_data;
+
+	/* function handler pdata */
+	struct rmi_2d_sensor_platform_data *sensor_pdata;
+	struct rmi_f01_power_management power_management;
+	struct rmi_f30_data *f30_data;
+};
+
+/**
+ * struct rmi_function_descriptor - RMI function base addresses
+ *
+ * @query_base_addr: The RMI Query base address
+ * @command_base_addr: The RMI Command base address
+ * @control_base_addr: The RMI Control base address
+ * @data_base_addr: The RMI Data base address
+ * @interrupt_source_count: The number of irqs this RMI function needs
+ * @function_number: The RMI function number
+ *
+ * This struct is used when iterating the Page Description Table. The addresses
+ * are 16-bit values to include the current page address.
+ *
+ */
+struct rmi_function_descriptor {
+	u16 query_base_addr;
+	u16 command_base_addr;
+	u16 control_base_addr;
+	u16 data_base_addr;
+	u8 interrupt_source_count;
+	u8 function_number;
+	u8 function_version;
+};
+
+struct rmi_device;
+
+/**
+ * struct rmi_transport_dev - represent an RMI transport device
+ *
+ * @dev: Pointer to the communication device, e.g. i2c or spi
+ * @rmi_dev: Pointer to the RMI device
+ * @proto_name: name of the transport protocol (SPI, i2c, etc)
+ * @ops: pointer to transport operations implementation
+ *
+ * The RMI transport device implements the glue between different communication
+ * buses such as I2C and SPI.
+ *
+ */
+struct rmi_transport_dev {
+	struct device *dev;
+	struct rmi_device *rmi_dev;
+
+	const char *proto_name;
+	const struct rmi_transport_ops *ops;
+
+	struct rmi_device_platform_data pdata;
+
+	struct input_dev *input;
+
+	void *attn_data;
+	int attn_size;
+};
+
+/**
+ * struct rmi_transport_ops - defines transport protocol operations.
+ *
+ * @write_block: Writing a block of data to the specified address
+ * @read_block: Read a block of data from the specified address.
+ */
+struct rmi_transport_ops {
+	int (*write_block)(struct rmi_transport_dev *xport, u16 addr,
+			   const void *buf, size_t len);
+	int (*read_block)(struct rmi_transport_dev *xport, u16 addr,
+			  void *buf, size_t len);
+	int (*reset)(struct rmi_transport_dev *xport, u16 reset_addr);
+};
+
+/**
+ * struct rmi_driver - driver for an RMI4 sensor on the RMI bus.
+ *
+ * @driver: Device driver model driver
+ * @reset_handler: Called when a reset is detected.
+ * @clear_irq_bits: Clear the specified bits in the current interrupt mask.
+ * @set_irq_bist: Set the specified bits in the current interrupt mask.
+ * @store_productid: Callback for cache product id from function 01
+ * @data: Private data pointer
+ *
+ */
+struct rmi_driver {
+	struct device_driver driver;
+
+	int (*reset_handler)(struct rmi_device *rmi_dev);
+	int (*clear_irq_bits)(struct rmi_device *rmi_dev, unsigned long *mask);
+	int (*set_irq_bits)(struct rmi_device *rmi_dev, unsigned long *mask);
+	int (*store_productid)(struct rmi_device *rmi_dev);
+	int (*set_input_params)(struct rmi_device *rmi_dev,
+			struct input_dev *input);
+	void *data;
+};
+
+/**
+ * struct rmi_device - represents an RMI4 sensor device on the RMI bus.
+ *
+ * @dev: The device created for the RMI bus
+ * @number: Unique number for the device on the bus.
+ * @driver: Pointer to associated driver
+ * @xport: Pointer to the transport interface
+ *
+ */
+struct rmi_device {
+	struct device dev;
+	int number;
+
+	struct rmi_driver *driver;
+	struct rmi_transport_dev *xport;
+
+};
+
+struct rmi_driver_data {
+	struct list_head function_list;
+
+	struct rmi_device *rmi_dev;
+
+	struct rmi_function *f01_container;
+	bool f01_bootloader_mode;
+
+	u32 attn_count;
+	int num_of_irq_regs;
+	int irq_count;
+	unsigned long *irq_status;
+	unsigned long *fn_irq_bits;
+	unsigned long *current_irq_mask;
+	unsigned long *new_irq_mask;
+	struct mutex irq_mutex;
+	struct input_dev *input;
+
+	u8 pdt_props;
+	u8 bsr;
+
+	bool enabled;
+
+	void *data;
+};
+
+int rmi_register_transport_device(struct rmi_transport_dev *xport);
+void rmi_unregister_transport_device(struct rmi_transport_dev *xport);
+int rmi_process_interrupt_requests(struct rmi_device *rmi_dev);
+
+int rmi_driver_suspend(struct rmi_device *rmi_dev);
+int rmi_driver_resume(struct rmi_device *rmi_dev);
+#endif

include/uapi/linux/input.h

@@ -246,6 +246,7 @@ struct input_mask {
 #define BUS_GSC			0x1A
 #define BUS_ATARI		0x1B
 #define BUS_SPI			0x1C
+#define BUS_RMI			0x1D
 
 /*
  * MT_TOOL types