Merge tag 'asoc-fix-v4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v4.3

Quite a few fixes here but they're all very small and driver specific,
none of them really stand out if you aren't using the relevant hardware
but they're all useful if you do happen to have an affected device.

Documentation/Changes

@@ -43,7 +43,7 @@ o  udev                   081                     # udevd --version
 o  grub                   0.93                    # grub --version || grub-install --version
 o  mcelog                 0.6                     # mcelog --version
 o  iptables               1.4.2                   # iptables -V
-o  openssl & libcrypto    1.0.1k                  # openssl version
+o  openssl & libcrypto    1.0.0                   # openssl version
 
 
 Kernel compilation

Documentation/devicetree/bindings/arm/gic-v3.txt

@@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs.
 These nodes must have the following properties:
 - compatible : Should at least contain  "arm,gic-v3-its".
 - msi-controller : Boolean property. Identifies the node as an MSI controller
+- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device
+  which will generate the MSI.
 - reg: Specifies the base physical address and size of the ITS
   registers.
 
@@ -83,6 +85,7 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 	};
@@ -107,12 +110,14 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 
 		gic-its@2c400000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c400000 0 0x200000>;
 		};
 	};

Documentation/devicetree/bindings/arm/idle-states.txt

@@ -497,7 +497,7 @@ cpus {
 	};
 
 	idle-states {
-		entry-method = "arm,psci";
+		entry-method = "psci";
 
 		CPU_RETENTION_0_0: cpu-retention-0-0 {
 			compatible = "arm,idle-state";

Documentation/devicetree/bindings/gpio/gpio.txt

@@ -16,7 +16,9 @@ properties, each containing a 'gpio-list':
 GPIO properties should be named "[<name>-]gpios", with <name> being the purpose
 of this GPIO for the device. While a non-existent <name> is considered valid
 for compatibility reasons (resolving to the "gpios" property), it is not allowed
-for new bindings.
+for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old
+bindings use it, but are only supported for compatibility reasons and should not
+be used for newer bindings since it has been deprecated.
 
 GPIO properties can contain one or more GPIO phandles, but only in exceptional
 cases should they contain more than one. If your device uses several GPIOs with

Documentation/devicetree/bindings/iio/accel/bma180.txt

@@ -1,10 +1,11 @@
-* Bosch BMA180 triaxial acceleration sensor
+* Bosch BMA180 / BMA250 triaxial acceleration sensor
 
 http://omapworld.com/BMA180_111_1002839.pdf
+http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf
 
 Required properties:
 
-  - compatible : should be "bosch,bma180"
+  - compatible : should be "bosch,bma180" or "bosch,bma250"
   - reg : the I2C address of the sensor
 
 Optional properties:
@@ -13,6 +14,9 @@ Optional properties:
 
   - interrupts : interrupt mapping for GPIO IRQ, it should by configured with
 		flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING
+		For the bma250 the first interrupt listed must be the one
+		connected to the INT1 pin, the second (optional) interrupt
+		listed must be the one connected to the INT2 pin.
 
 Example:
 

Documentation/devicetree/bindings/input/cypress,cyapa.txt

@@ -25,7 +25,7 @@ Example:
 		/* Cypress Gen3 touchpad */
 		touchpad@67 {
 			compatible = "cypress,cyapa";
-			reg = <0x24>;
+			reg = <0x67>;
 			interrupt-parent = <&gpio>;
 			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;	/* GPIO 2 */
 			wakeup-source;

Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt

@@ -4,8 +4,8 @@ The MISC interrupt controller is a secondary controller for lower priority
 interrupt.
 
 Required Properties:
-- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc"
-  as fallback
+- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" or
+  "qca,<soctype>-cpu-intc", "qca,ar7240-misc-intc"
 - reg: Base address and size of the controllers memory area
 - interrupt-parent: phandle of the parent interrupt controller.
 - interrupts: Interrupt specifier for the controllers interrupt.
@@ -13,6 +13,9 @@ Required Properties:
 - #interrupt-cells : Specifies the number of cells needed to encode interrupt
 		     source, should be 1
 
+Compatible fallback depends on the SoC. Use ar7100 for ar71xx and ar913x,
+use ar7240 for all other SoCs.
+
 Please refer to interrupts.txt in this directory for details of the common
 Interrupt Controllers bindings used by client devices.
 
@@ -28,3 +31,16 @@ Example:
 		interrupt-controller;
 		#interrupt-cells = <1>;
 	};
+
+Another example:
+
+	interrupt-controller@18060010 {
+		compatible = "qca,ar9331-misc-intc", qca,ar7240-misc-intc";
+		reg = <0x18060010 0x4>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <6>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};

Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt

@@ -7,7 +7,8 @@ OHCI and EHCI controllers.
 
 Required properties:
 - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
-	      "renesas,pci-r8a7791" for the R8A7791 SoC.
+	      "renesas,pci-r8a7791" for the R8A7791 SoC;
+	      "renesas,pci-r8a7794" for the R8A7794 SoC.
 - reg:	A list of physical regions to access the device: the first is
 	the operational registers for the OHCI/EHCI controllers and the
 	second is for the bridge configuration and control registers.

Documentation/devicetree/bindings/regulator/pbias-regulator.txt

@@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs.
 
 Required properties:
 - compatible:
-  - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7.
+  - should be "ti,pbias-dra7" for DRA7
+  - should be "ti,pbias-omap2" for OMAP2
+  - should be "ti,pbias-omap3" for OMAP3
+  - should be "ti,pbias-omap4" for OMAP4
+  - should be "ti,pbias-omap5" for OMAP5
+  - "ti,pbias-omap" is deprecated
 - reg: pbias register offset from syscon base and size of pbias register.
 - syscon : phandle of the system control module
 - regulator-name : should be

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

@@ -15,17 +15,18 @@ Required properties:
 - interrupts: Should contain spi interrupt
 
 - clocks: phandles to input clocks.
-  The first should be <&topckgen CLK_TOP_SPI_SEL>.
-  The second should be one of the following.
+  The first should be one of the following. It's PLL.
    -  <&clk26m>: specify parent clock 26MHZ.
    -  <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ.
 				      It's the default one.
    -  <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+  The second should be <&topckgen CLK_TOP_SPI_SEL>. It's clock mux.
+  The third is <&pericfg CLK_PERI_SPI0>. It's clock gate.
 
-- clock-names: shall be "spi-clk" for the controller clock, and
-  "parent-clk" for the parent clock.
+- clock-names: shall be "parent-clk" for the parent clock, "sel-clk" for the
+  muxes clock, and "spi-clk" for the clock gate.
 
 Optional properties:
 - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
@@ -44,8 +45,11 @@ spi: spi@1100a000 {
 	#size-cells = <0>;
 	reg = <0 0x1100a000 0 0x1000>;
 	interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>;
-	clock-names = "spi-clk", "parent-clk";
+	clocks = <&topckgen CLK_TOP_SYSPLL3_D2>,
+		 <&topckgen CLK_TOP_SPI_SEL>,
+		 <&pericfg CLK_PERI_SPI0>;
+	clock-names = "parent-clk", "sel-clk", "spi-clk";
+
 	mediatek,pad-select = <0>;
 	status = "disabled";
 };

Documentation/devicetree/bindings/thermal/thermal.txt

@@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to
 the different fan speeds possible. Cooling states are referred to by
 single unsigned integers, where larger numbers mean greater heat
 dissipation. The precise set of cooling states associated with a device
-(as referred to be the cooling-min-state and cooling-max-state
+(as referred to by the cooling-min-level and cooling-max-level
 properties) should be defined in a particular device's binding.
 For more examples of cooling devices, refer to the example sections below.
 
 Required properties:
-- cooling-min-state:	An integer indicating the smallest
-  Type: unsigned	cooling state accepted. Typically 0.
-  Size: one cell
-
-- cooling-max-state:	An integer indicating the largest
-  Type: unsigned	cooling state accepted.
-  Size: one cell
-
 - #cooling-cells:	Used to provide cooling device specific information
   Type: unsigned	while referring to it. Must be at least 2, in order
   Size: one cell      	to specify minimum and maximum cooling state used
@@ -77,6 +69,15 @@ Required properties:
 			See Cooling device maps section below for more details
 			on how consumers refer to cooling devices.
 
+Optional properties:
+- cooling-min-level:	An integer indicating the smallest
+  Type: unsigned	cooling state accepted. Typically 0.
+  Size: one cell
+
+- cooling-max-level:	An integer indicating the largest
+  Type: unsigned	cooling state accepted.
+  Size: one cell
+
 * Trip points
 
 The trip node is a node to describe a point in the temperature domain
@@ -225,8 +226,8 @@ cpus {
 			396000  950000
 			198000  850000
 		>;
-		cooling-min-state = <0>;
-		cooling-max-state = <3>;
+		cooling-min-level = <0>;
+		cooling-max-level = <3>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 	...
@@ -240,8 +241,8 @@ cpus {
 	 */
 	fan0: fan@0x48 {
 		...
-		cooling-min-state = <0>;
-		cooling-max-state = <9>;
+		cooling-min-level = <0>;
+		cooling-max-level = <9>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 };

Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt

@@ -6,6 +6,7 @@ Required properties:
 	"lsi,zevio-usb"
 	"qcom,ci-hdrc"
 	"chipidea,usb2"
+	"xlnx,zynq-usb-2.20a"
 - reg: base address and length of the registers
 - interrupts: interrupt for the USB controller
 

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -203,6 +203,7 @@ sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
+socionext	Socionext Inc.
 solidrun	SolidRun
 solomon        Solomon Systech Limited
 sony	Sony Corporation

Documentation/input/multi-touch-protocol.txt

@@ -361,7 +361,7 @@ For win8 devices with both T and C coordinates, the position mapping is
    ABS_MT_POSITION_X := T_X
    ABS_MT_POSITION_Y := T_Y
    ABS_MT_TOOL_X := C_X
-   ABS_MT_TOOL_X := C_Y
+   ABS_MT_TOOL_Y := C_Y
 
 Unfortunately, there is not enough information to specify both the touching
 ellipse and the tool ellipse, so one has to resort to approximations.  One

Documentation/networking/vrf.txt

@@ -0,0 +1,96 @@
+Virtual Routing and Forwarding (VRF)
+====================================
+The VRF device combined with ip rules provides the ability to create virtual
+routing and forwarding domains (aka VRFs, VRF-lite to be specific) in the
+Linux network stack. One use case is the multi-tenancy problem where each
+tenant has their own unique routing tables and in the very least need
+different default gateways.
+
+Processes can be "VRF aware" by binding a socket to the VRF device. Packets
+through the socket then use the routing table associated with the VRF
+device. An important feature of the VRF device implementation is that it
+impacts only Layer 3 and above so L2 tools (e.g., LLDP) are not affected
+(ie., they do not need to be run in each VRF). The design also allows
+the use of higher priority ip rules (Policy Based Routing, PBR) to take
+precedence over the VRF device rules directing specific traffic as desired.
+
+In addition, VRF devices allow VRFs to be nested within namespaces. For
+example network namespaces provide separation of network interfaces at L1
+(Layer 1 separation), VLANs on the interfaces within a namespace provide
+L2 separation and then VRF devices provide L3 separation.
+
+Design
+------
+A VRF device is created with an associated route table. Network interfaces
+are then enslaved to a VRF device:
+
+         +-----------------------------+
+         |           vrf-blue          |  ===> route table 10
+         +-----------------------------+
+            |        |            |
+         +------+ +------+     +-------------+
+         | eth1 | | eth2 | ... |    bond1    |
+         +------+ +------+     +-------------+
+                                  |       |
+                              +------+ +------+
+                              | eth8 | | eth9 |
+                              +------+ +------+
+
+Packets received on an enslaved device and are switched to the VRF device
+using an rx_handler which gives the impression that packets flow through
+the VRF device. Similarly on egress routing rules are used to send packets
+to the VRF device driver before getting sent out the actual interface. This
+allows tcpdump on a VRF device to capture all packets into and out of the
+VRF as a whole.[1] Similiarly, netfilter [2] and tc rules can be applied
+using the VRF device to specify rules that apply to the VRF domain as a whole.
+
+[1] Packets in the forwarded state do not flow through the device, so those
+    packets are not seen by tcpdump. Will revisit this limitation in a
+    future release.
+
+[2] Iptables on ingress is limited to NF_INET_PRE_ROUTING only with skb->dev
+    set to real ingress device and egress is limited to NF_INET_POST_ROUTING.
+    Will revisit this limitation in a future release.
+
+
+Setup
+-----
+1. VRF device is created with an association to a FIB table.
+   e.g, ip link add vrf-blue type vrf table 10
+        ip link set dev vrf-blue up
+
+2. Rules are added that send lookups to the associated FIB table when the
+   iif or oif is the VRF device. e.g.,
+       ip ru add oif vrf-blue table 10
+       ip ru add iif vrf-blue table 10
+
+   Set the default route for the table (and hence default route for the VRF).
+   e.g, ip route add table 10 prohibit default
+
+3. Enslave L3 interfaces to a VRF device.
+   e.g,  ip link set dev eth1 master vrf-blue
+
+   Local and connected routes for enslaved devices are automatically moved to
+   the table associated with VRF device. Any additional routes depending on
+   the enslaved device will need to be reinserted following the enslavement.
+
+4. Additional VRF routes are added to associated table.
+   e.g., ip route add table 10 ...
+
+
+Applications
+------------
+Applications that are to work within a VRF need to bind their socket to the
+VRF device:
+
+    setsockopt(sd, SOL_SOCKET, SO_BINDTODEVICE, dev, strlen(dev)+1);
+
+or to specify the output device using cmsg and IP_PKTINFO.
+
+
+Limitations
+-----------
+VRF device currently only works for IPv4. Support for IPv6 is under development.
+
+Index of original ingress interface is not available via cmsg. Will address
+soon.

Documentation/power/pci.txt

@@ -979,20 +979,45 @@ every time right after the runtime_resume() callback has returned
 (alternatively, the runtime_suspend() callback will have to check if the
 device should really be suspended and return -EAGAIN if that is not the case).
 
-The runtime PM of PCI devices is disabled by default.  It is also blocked by
-pci_pm_init() that runs the pm_runtime_forbid() helper function.  If a PCI
-driver implements the runtime PM callbacks and intends to use the runtime PM
-framework provided by the PM core and the PCI subsystem, it should enable this
-feature by executing the pm_runtime_enable() helper function.  However, the
-driver should not call the pm_runtime_allow() helper function unblocking
-the runtime PM of the device.  Instead, it should allow user space or some
-platform-specific code to do that (user space can do it via sysfs), although
-once it has called pm_runtime_enable(), it must be prepared to handle the
+The runtime PM of PCI devices is enabled by default by the PCI core.  PCI
+device drivers do not need to enable it and should not attempt to do so.
+However, it is blocked by pci_pm_init() that runs the pm_runtime_forbid()
+helper function.  In addition to that, the runtime PM usage counter of
+each PCI device is incremented by local_pci_probe() before executing the
+probe callback provided by the device's driver.
+
+If a PCI driver implements the runtime PM callbacks and intends to use the
+runtime PM framework provided by the PM core and the PCI subsystem, it needs
+to decrement the device's runtime PM usage counter in its probe callback
+function.  If it doesn't do that, the counter will always be different from
+zero for the device and it will never be runtime-suspended.  The simplest
+way to do that is by calling pm_runtime_put_noidle(), but if the driver
+wants to schedule an autosuspend right away, for example, it may call
+pm_runtime_put_autosuspend() instead for this purpose.  Generally, it
+just needs to call a function that decrements the devices usage counter
+from its probe routine to make runtime PM work for the device.
+
+It is important to remember that the driver's runtime_suspend() callback
+may be executed right after the usage counter has been decremented, because
+user space may already have cuased the pm_runtime_allow() helper function
+unblocking the runtime PM of the device to run via sysfs, so the driver must
+be prepared to cope with that.
+
+The driver itself should not call pm_runtime_allow(), though.  Instead, it
+should let user space or some platform-specific code do that (user space can
+do it via sysfs as stated above), but it must be prepared to handle the
 runtime PM of the device correctly as soon as pm_runtime_allow() is called
-(which may happen at any time).  [It also is possible that user space causes
-pm_runtime_allow() to be called via sysfs before the driver is loaded, so in
-fact the driver has to be prepared to handle the runtime PM of the device as
-soon as it calls pm_runtime_enable().]
+(which may happen at any time, even before the driver is loaded).
+
+When the driver's remove callback runs, it has to balance the decrementation
+of the device's runtime PM usage counter at the probe time.  For this reason,
+if it has decremented the counter in its probe callback, it must run
+pm_runtime_get_noresume() in its remove callback.  [Since the core carries
+out a runtime resume of the device and bumps up the device's usage counter
+before running the driver's remove callback, the runtime PM of the device
+is effectively disabled for the duration of the remove execution and all
+runtime PM helper functions incrementing the device's usage counter are
+then effectively equivalent to pm_runtime_get_noresume().]
 
 The runtime PM framework works by processing requests to suspend or resume
 devices, or to check if they are idle (in which cases it is reasonable to

Documentation/ptp/testptp.c

@@ -18,6 +18,7 @@
  *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 #define _GNU_SOURCE
+#define __SANE_USERSPACE_TYPES__        /* For PPC64, to get LL64 types */
 #include <errno.h>
 #include <fcntl.h>
 #include <inttypes.h>

Documentation/sysctl/net.txt

@@ -54,13 +54,15 @@ default_qdisc
 --------------
 
 The default queuing discipline to use for network devices. This allows
-overriding the default queue discipline of pfifo_fast with an
-alternative. Since the default queuing discipline is created with the
-no additional parameters so is best suited to queuing disciplines that
-work well without configuration like stochastic fair queue (sfq),
-CoDel (codel) or fair queue CoDel (fq_codel). Don't use queuing disciplines
-like Hierarchical Token Bucket or Deficit Round Robin which require setting
-up classes and bandwidths.
+overriding the default of pfifo_fast with an alternative. Since the default
+queuing discipline is created without additional parameters so is best suited
+to queuing disciplines that work well without configuration like stochastic
+fair queue (sfq), CoDel (codel) or fair queue CoDel (fq_codel). Don't use
+queuing disciplines like Hierarchical Token Bucket or Deficit Round Robin
+which require setting up classes and bandwidths. Note that physical multiqueue
+interfaces still use mq as root qdisc, which in turn uses this default for its
+leaves. Virtual devices (like e.g. lo or veth) ignore this setting and instead
+default to noqueue.
 Default: pfifo_fast
 
 busy_read

Documentation/thermal/power_allocator.txt

@@ -4,7 +4,7 @@ Power allocator governor tunables
 Trip points
 -----------
 
-The governor requires the following two passive trip points:
+The governor works optimally with the following two passive trip points:
 
 1.  "switch on" trip point: temperature above which the governor
     control loop starts operating.  This is the first passive trip

MAINTAINERS

@@ -615,9 +615,8 @@ F:	Documentation/hwmon/fam15h_power
 F:	drivers/hwmon/fam15h_power.c
 
 AMD GEODE CS5536 USB DEVICE CONTROLLER DRIVER
-M:	Thomas Dahlmann <dahlmann.thomas@arcor.de>
 L:	linux-geode@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Orphan
 F:	drivers/usb/gadget/udc/amd5536udc.*
 
 AMD GEODE PROCESSOR/CHIPSET SUPPORT
@@ -808,6 +807,13 @@ S:	Maintained
 F:	drivers/video/fbdev/arcfb.c
 F:	drivers/video/fbdev/core/fb_defio.c
 
+ARCNET NETWORK LAYER
+M:	Michael Grzeschik <m.grzeschik@pengutronix.de>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	drivers/net/arcnet/
+F:	include/uapi/linux/if_arcnet.h
+
 ARM MFM AND FLOPPY DRIVERS
 M:	Ian Molton <spyro@f2s.com>
 S:	Maintained
@@ -3394,7 +3400,6 @@ F:	drivers/staging/dgnc/
 
 DIGI EPCA PCI PRODUCTS
 M:	Lidza Louina <lidza.louina@gmail.com>
-M:	Mark Hounschell <markh@compro.net>
 M:	Daeseok Youn <daeseok.youn@gmail.com>
 L:	driverdev-devel@linuxdriverproject.org
 S:	Maintained
@@ -5952,7 +5957,7 @@ F:	virt/kvm/
 KERNEL VIRTUAL MACHINE (KVM) FOR AMD-V
 M:	Joerg Roedel <joro@8bytes.org>
 L:	kvm@vger.kernel.org
-W:	http://kvm.qumranet.com
+W:	http://www.linux-kvm.org/
 S:	Maintained
 F:	arch/x86/include/asm/svm.h
 F:	arch/x86/kvm/svm.c
@@ -5960,7 +5965,7 @@ F:	arch/x86/kvm/svm.c
 KERNEL VIRTUAL MACHINE (KVM) FOR POWERPC
 M:	Alexander Graf <agraf@suse.com>
 L:	kvm-ppc@vger.kernel.org
-W:	http://kvm.qumranet.com
+W:	http://www.linux-kvm.org/
 T:	git git://github.com/agraf/linux-2.6.git
 S:	Supported
 F:	arch/powerpc/include/asm/kvm*
@@ -8500,7 +8505,6 @@ F:	Documentation/networking/LICENSE.qla3xxx
 F:	drivers/net/ethernet/qlogic/qla3xxx.*
 
 QLOGIC QLCNIC (1/10)Gb ETHERNET DRIVER
-M:	Shahed Shaikh <shahed.shaikh@qlogic.com>
 M:	Dept-GELinuxNICDev@qlogic.com
 L:	netdev@vger.kernel.org
 S:	Supported
@@ -9904,8 +9908,8 @@ F:	drivers/staging/media/lirc/
 STAGING - LUSTRE PARALLEL FILESYSTEM
 M:	Oleg Drokin <oleg.drokin@intel.com>
 M:	Andreas Dilger <andreas.dilger@intel.com>
-L:	HPDD-discuss@lists.01.org (moderated for non-subscribers)
-W:	http://lustre.opensfs.org/
+L:	lustre-devel@lists.lustre.org (moderated for non-subscribers)
+W:	http://wiki.lustre.org/
 S:	Maintained
 F:	drivers/staging/lustre
 
@@ -10338,6 +10342,16 @@ F:	include/uapi/linux/thermal.h
 F:	include/linux/cpu_cooling.h
 F:	Documentation/devicetree/bindings/thermal/
 
+THERMAL/CPU_COOLING
+M:	Amit Daniel Kachhap <amit.kachhap@gmail.com>
+M:	Viresh Kumar <viresh.kumar@linaro.org>
+M:	Javi Merino <javi.merino@arm.com>
+L:	linux-pm@vger.kernel.org
+S:	Supported
+F:	Documentation/thermal/cpu-cooling-api.txt
+F:	drivers/thermal/cpu_cooling.c
+F:	include/linux/cpu_cooling.h
+
 THINGM BLINK(1) USB RGB LED DRIVER
 M:	Vivien Didelot <vivien.didelot@savoirfairelinux.com>
 S:	Maintained
@@ -11187,7 +11201,7 @@ F:	drivers/vlynq/vlynq.c
 F:	include/linux/vlynq.h
 
 VME SUBSYSTEM
-M:	Martyn Welch <martyn.welch@ge.com>
+M:	Martyn Welch <martyn@welchs.me.uk>
 M:	Manohar Vanga <manohar.vanga@gmail.com>
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	devel@driverdev.osuosl.org
@@ -11252,6 +11266,7 @@ L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/vrf.c
 F:	include/net/vrf.h
+F:	Documentation/networking/vrf.txt
 
 VT1211 HARDWARE MONITOR DRIVER
 M:	Juerg Haefliger <juergh@gmail.com>
@@ -11363,15 +11378,6 @@ W:	http://oops.ghostprotocols.net:81/blog
 S:	Maintained
 F:	drivers/net/wireless/wl3501*
 
-WM97XX TOUCHSCREEN DRIVERS
-M:	Mark Brown <broonie@kernel.org>
-M:	Liam Girdwood <lrg@slimlogic.co.uk>
-L:	linux-input@vger.kernel.org
-W:	https://github.com/CirrusLogic/linux-drivers/wiki
-S:	Supported
-F:	drivers/input/touchscreen/*wm97*
-F:	include/linux/wm97xx.h
-
 WOLFSON MICROELECTRONICS DRIVERS
 L:	patches@opensource.wolfsonmicro.com
 T:	git https://github.com/CirrusLogic/linux-drivers.git

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 3
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc4
 NAME = Hurr durr I'ma sheep
 
 # *DOCUMENTATION*

arch/alpha/kernel/pci.c

@@ -242,7 +242,12 @@ pci_restore_srm_config(void)
 
 void pcibios_fixup_bus(struct pci_bus *bus)
 {
-	struct pci_dev *dev;
+	struct pci_dev *dev = bus->self;
+
+	if (pci_has_flag(PCI_PROBE_ONLY) && dev &&
+	    (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
+		pci_read_bridge_bases(bus);
+	}
 
 	list_for_each_entry(dev, &bus->devices, bus_list) {
 		pdev_save_srm_config(dev);

arch/arc/include/asm/Kbuild

@@ -48,4 +48,5 @@ generic-y += types.h
 generic-y += ucontext.h
 generic-y += user.h
 generic-y += vga.h
+generic-y += word-at-a-time.h
 generic-y += xor.h

arch/arm/boot/dts/am335x-phycore-som.dtsi

@@ -252,10 +252,10 @@
 		};
 
 		vdd1_reg: regulator@2 {
-			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			/* VDD_MPU voltage limits 0.95V - 1.325V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <912500>;
-			regulator-max-microvolt = <1312500>;
+			regulator-max-microvolt = <1378000>;
 			regulator-boot-on;
 			regulator-always-on;
 		};

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -98,13 +98,6 @@
 		pinctrl-0 = <&extcon_usb1_pins>;
 	};
 
-	extcon_usb2: extcon_usb2 {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&gpio7 24 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&extcon_usb2_pins>;
-	};
-
 	hdmi0: connector {
 		compatible = "hdmi-connector";
 		label = "hdmi";
@@ -326,12 +319,6 @@
 		>;
 	};
 
-	extcon_usb2_pins: extcon_usb2_pins {
-		pinctrl-single,pins = <
-			0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */
-		>;
-	};
-
 	tpd12s015_pins: pinmux_tpd12s015_pins {
 		pinctrl-single,pins = <
 			0x3b0 (PIN_OUTPUT | MUX_MODE14)		/* gpio7_10 CT_CP_HPD */
@@ -432,7 +419,7 @@
 				};
 
 				ldo3_reg: ldo3 {
-					/* VDDA_1V8_PHY */
+					/* VDDA_1V8_PHYA */
 					regulator-name = "ldo3";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -440,6 +427,15 @@
 					regulator-boot-on;
 				};
 
+				ldo4_reg: ldo4 {
+					/* VDDA_1V8_PHYB */
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
 				ldo9_reg: ldo9 {
 					/* VDD_RTC */
 					regulator-name = "ldo9";
@@ -495,6 +491,14 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
+
+		extcon_usb2: tps659038_usb {
+			compatible = "ti,palmas-usb-vid";
+			ti,enable-vbus-detection;
+			ti,enable-id-detection;
+			id-gpios = <&gpio7 24 GPIO_ACTIVE_HIGH>;
+		};
+
 	};
 
 	tmp102: tmp102@48 {
@@ -517,7 +521,8 @@
 	mcp_rtc: rtc@6f {
 		compatible = "microchip,mcp7941x";
 		reg = <0x6f>;
-		interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>;  /* IRQ_SYS_1N */
+		interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>,
+				      <&dra7_pmx_core 0x424>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcp79410_pins_default>;
@@ -579,7 +584,6 @@
 	pinctrl-0 = <&mmc1_pins_default>;
 
 	vmmc-supply = <&ldo1_reg>;
-	vmmc_aux-supply = <&vdd_3v3>;
 	bus-width = <4>;
 	cd-gpios = <&gpio6 27 0>; /* gpio 219 */
 };
@@ -623,6 +627,14 @@
 };
 
 &usb2 {
+	/*
+	 * Stand alone usage is peripheral only.
+	 * However, with some resistor modifications
+	 * this port can be used via expansion connectors
+	 * as "host" or "dual-role". If so, provide
+	 * the necessary dr_mode override in the expansion
+	 * board's DT.
+	 */
 	dr_mode = "peripheral";
 };
 
@@ -681,7 +693,7 @@
 
 &hdmi {
 	status = "ok";
-	vdda-supply = <&ldo3_reg>;
+	vdda-supply = <&ldo4_reg>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&hdmi_pins>;

arch/arm/boot/dts/dm8148-evm.dts

@@ -19,10 +19,10 @@
 
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };

arch/arm/boot/dts/dm8148-t410.dts

@@ -8,7 +8,7 @@
 #include "dm814x.dtsi"
 
 / {
-	model = "DM8148 EVM";
+	model = "HP t410 Smart Zero Client";
 	compatible = "hp,t410", "ti,dm8148";
 
 	memory {
@@ -19,10 +19,10 @@
 
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };

arch/arm/boot/dts/dm814x.dtsi

@@ -181,9 +181,9 @@
 				ti,hwmods = "timer3";
 			};
 
-			control: control@160000 {
+			control: control@140000 {
 				compatible = "ti,dm814-scm", "simple-bus";
-				reg = <0x160000 0x16d000>;
+				reg = <0x140000 0x16d000>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0 0x160000 0x16d000>;
@@ -321,9 +321,9 @@
 				mac-address = [ 00 00 00 00 00 00 ];
 			};
 
-			phy_sel: cpsw-phy-sel@0x48160650 {
+			phy_sel: cpsw-phy-sel@48140650 {
 				compatible = "ti,am3352-cpsw-phy-sel";
-				reg= <0x48160650 0x4>;
+				reg= <0x48140650 0x4>;
 				reg-names = "gmii-sel";
 			};
 		};

arch/arm/boot/dts/dra7.dtsi

@@ -120,9 +120,10 @@
 					reg = <0x0 0x1400>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x0 0x1400>;
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-dra7", "ti,pbias-omap";
 						reg = <0xe00 0x4>;
 						syscon = <&scm_conf>;
 						pbias_mmc_reg: pbias_mmc_omap5 {
@@ -1417,7 +1418,7 @@
 			ti,irqs-safe-map = <0>;
 		};
 
-		mac: ethernet@4a100000 {
+		mac: ethernet@48484000 {
 			compatible = "ti,dra7-cpsw","ti,cpsw";
 			ti,hwmods = "gmac";
 			clocks = <&dpll_gmac_ck>, <&gmac_gmii_ref_clk_div>;

arch/arm/boot/dts/omap2430.dtsi

@@ -56,6 +56,7 @@
 					reg = <0x270 0x240>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x270 0x240>;
 
 					scm_clocks: clocks {
 						#address-cells = <1>;
@@ -63,7 +64,7 @@
 					};
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-omap2", "ti,pbias-omap";
 						reg = <0x230 0x4>;
 						syscon = <&scm_conf>;
 						pbias_mmc_reg: pbias_mmc_omap2430 {

arch/arm/boot/dts/omap3-beagle.dts

@@ -202,7 +202,7 @@
 
 	tfp410_pins: pinmux_tfp410_pins {
 		pinctrl-single,pins = <
-			0x194 (PIN_OUTPUT | MUX_MODE4)	/* hdq_sio.gpio_170 */
+			0x196 (PIN_OUTPUT | MUX_MODE4)	/* hdq_sio.gpio_170 */
 		>;
 	};
 

arch/arm/boot/dts/omap3-igep.dtsi

@@ -78,12 +78,6 @@
 		>;
 	};
 
-	smsc9221_pins: pinmux_smsc9221_pins {
-		pinctrl-single,pins = <
-			0x1a2 (PIN_INPUT | MUX_MODE4)		/* mcspi1_cs2.gpio_176 */
-		>;
-	};
-
 	i2c1_pins: pinmux_i2c1_pins {
 		pinctrl-single,pins = <
 			0x18a (PIN_INPUT | MUX_MODE0)   /* i2c1_scl.i2c1_scl */

arch/arm/boot/dts/omap3-igep0020-common.dtsi

@@ -156,6 +156,12 @@
 			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)	/* uart2_rx.uart2_rx */
 		>;
 	};
+
+	smsc9221_pins: pinmux_smsc9221_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4)	/* mcspi1_cs2.gpio_176 */
+		>;
+	};
 };
 
 &omap3_pmx_core2 {

arch/arm/boot/dts/omap3.dtsi

@@ -113,10 +113,22 @@
 				};
 
 				scm_conf: scm_conf@270 {
-					compatible = "syscon";
+					compatible = "syscon", "simple-bus";
 					reg = <0x270 0x330>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x270 0x330>;
+
+					pbias_regulator: pbias_regulator {
+						compatible = "ti,pbias-omap3", "ti,pbias-omap";
+						reg = <0x2b0 0x4>;
+						syscon = <&scm_conf>;
+						pbias_mmc_reg: pbias_mmc_omap2430 {
+							regulator-name = "pbias_mmc_omap2430";
+							regulator-min-microvolt = <1800000>;
+							regulator-max-microvolt = <3000000>;
+						};
+					};
 
 					scm_clocks: clocks {
 						#address-cells = <1>;
@@ -202,17 +214,6 @@
 			dma-requests = <96>;
 		};
 
-		pbias_regulator: pbias_regulator {
-			compatible = "ti,pbias-omap";
-			reg = <0x2b0 0x4>;
-			syscon = <&scm_conf>;
-			pbias_mmc_reg: pbias_mmc_omap2430 {
-				regulator-name = "pbias_mmc_omap2430";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3000000>;
-			};
-		};
-
 		gpio1: gpio@48310000 {
 			compatible = "ti,omap3-gpio";
 			reg = <0x48310000 0x200>;

arch/arm/boot/dts/omap4.dtsi

@@ -196,9 +196,10 @@
 					reg = <0x5a0 0x170>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x5a0 0x170>;
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-omap4", "ti,pbias-omap";
 						reg = <0x60 0x4>;
 						syscon = <&omap4_padconf_global>;
 						pbias_mmc_reg: pbias_mmc_omap4 {

arch/arm/boot/dts/omap5-uevm.dts

@@ -174,8 +174,8 @@
 
 	i2c5_pins: pinmux_i2c5_pins {
 		pinctrl-single,pins = <
-			0x184 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
-			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
+			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
+			0x188 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
 		>;
 	};
 

arch/arm/boot/dts/omap5.dtsi

@@ -185,9 +185,10 @@
 					reg = <0x5a0 0xec>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x5a0 0xec>;
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-omap5", "ti,pbias-omap";
 						reg = <0x60 0x4>;
 						syscon = <&omap5_padconf_global>;
 						pbias_mmc_reg: pbias_mmc_omap5 {

arch/arm/boot/dts/rk3288-veyron.dtsi

@@ -158,6 +158,7 @@
 };
 
 &hdmi {
+	ddc-i2c-bus = <&i2c5>;
 	status = "okay";
 };
 

arch/arm/boot/dts/stih407.dtsi

@@ -103,48 +103,46 @@
 							 <&clk_s_d0_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>;
-				ranges;
-
-				sti-hdmi@8d04000 {
-					compatible = "st,stih407-hdmi";
-					reg = <0x8d04000 0x1000>;
-					reg-names = "hdmi-reg";
-					interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
-					interrupt-names	= "irq";
-					clock-names = "pix",
-						      "tmds",
-						      "phy",
-						      "audio",
-						      "main_parent",
-						      "aux_parent";
-
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
-						 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
-						 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
-						 <&clk_s_d0_flexgen CLK_PCM_0>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-
-					hdmi,hpd-gpio = <&pio5 3>;
-					reset-names = "hdmi";
-					resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
-					ddc = <&hdmiddc>;
-
-				};
-
-				sti-hda@8d02000 {
-					compatible = "st,stih407-hda";
-					reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
-					reg-names = "hda-reg", "video-dacs-ctrl";
-					clock-names = "pix",
-						      "hddac",
-						      "main_parent",
-						      "aux_parent";
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
-						 <&clk_s_d2_flexgen CLK_HDDAC>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-				};
+			};
+
+			sti-hdmi@8d04000 {
+				compatible = "st,stih407-hdmi";
+				reg = <0x8d04000 0x1000>;
+				reg-names = "hdmi-reg";
+				interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
+				interrupt-names	= "irq";
+				clock-names = "pix",
+					      "tmds",
+					      "phy",
+					      "audio",
+					      "main_parent",
+					      "aux_parent";
+
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+					 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+					 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+					 <&clk_s_d0_flexgen CLK_PCM_0>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+
+				hdmi,hpd-gpio = <&pio5 3>;
+				reset-names = "hdmi";
+				resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
+				ddc = <&hdmiddc>;
+			};
+
+			sti-hda@8d02000 {
+				compatible = "st,stih407-hda";
+				reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
+				reg-names = "hda-reg", "video-dacs-ctrl";
+				clock-names = "pix",
+					      "hddac",
+					      "main_parent",
+					      "aux_parent";
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+					 <&clk_s_d2_flexgen CLK_HDDAC>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
 			};
 		};
 	};

arch/arm/boot/dts/stih410.dtsi

@@ -178,48 +178,46 @@
 							 <&clk_s_d0_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>;
-				ranges;
-
-				sti-hdmi@8d04000 {
-					compatible = "st,stih407-hdmi";
-					reg = <0x8d04000 0x1000>;
-					reg-names = "hdmi-reg";
-					interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
-					interrupt-names	= "irq";
-					clock-names = "pix",
-						      "tmds",
-						      "phy",
-						      "audio",
-						      "main_parent",
-						      "aux_parent";
-
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
-						 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
-						 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
-						 <&clk_s_d0_flexgen CLK_PCM_0>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-
-					hdmi,hpd-gpio = <&pio5 3>;
-					reset-names = "hdmi";
-					resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
-					ddc = <&hdmiddc>;
-
-				};
-
-				sti-hda@8d02000 {
-					compatible = "st,stih407-hda";
-					reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
-					reg-names = "hda-reg", "video-dacs-ctrl";
-					clock-names = "pix",
-						      "hddac",
-						      "main_parent",
-						      "aux_parent";
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
-						 <&clk_s_d2_flexgen CLK_HDDAC>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-				};
+			};
+
+			sti-hdmi@8d04000 {
+				compatible = "st,stih407-hdmi";
+				reg = <0x8d04000 0x1000>;
+				reg-names = "hdmi-reg";
+				interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
+				interrupt-names	= "irq";
+				clock-names = "pix",
+					      "tmds",
+					      "phy",
+					      "audio",
+					      "main_parent",
+					      "aux_parent";
+
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+					 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+					 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+					 <&clk_s_d0_flexgen CLK_PCM_0>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+
+				hdmi,hpd-gpio = <&pio5 3>;
+				reset-names = "hdmi";
+				resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
+				ddc = <&hdmiddc>;
+			};
+
+			sti-hda@8d02000 {
+				compatible = "st,stih407-hda";
+				reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
+				reg-names = "hda-reg", "video-dacs-ctrl";
+				clock-names = "pix",
+					      "hddac",
+					      "main_parent",
+					      "aux_parent";
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+					 <&clk_s_d2_flexgen CLK_HDDAC>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
 			};
 		};
 

arch/arm/configs/omap2plus_defconfig

@@ -240,7 +240,8 @@ CONFIG_SSI_PROTOCOL=m
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_DEBUG_GPIO=y
 CONFIG_GPIO_SYSFS=y
-CONFIG_GPIO_PCF857X=m
+CONFIG_GPIO_PCA953X=m
+CONFIG_GPIO_PCF857X=y
 CONFIG_GPIO_TWL4030=y
 CONFIG_GPIO_PALMAS=y
 CONFIG_W1=m
@@ -350,6 +351,8 @@ CONFIG_USB_MUSB_HDRC=m
 CONFIG_USB_MUSB_OMAP2PLUS=m
 CONFIG_USB_MUSB_AM35X=m
 CONFIG_USB_MUSB_DSPS=m
+CONFIG_USB_INVENTRA_DMA=y
+CONFIG_USB_TI_CPPI41_DMA=y
 CONFIG_USB_DWC3=m
 CONFIG_USB_TEST=m
 CONFIG_AM335X_PHY_USB=y

arch/arm/include/asm/kvm_host.h

@@ -33,6 +33,7 @@
 #define KVM_PRIVATE_MEM_SLOTS 4
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
 #define KVM_HAVE_ONE_REG
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 #define KVM_VCPU_MAX_FEATURES 2
 

arch/arm/include/asm/unistd.h

@@ -19,7 +19,7 @@
  * This may need to be greater than __NR_last_syscall+1 in order to
  * account for the padding in the syscall table
  */
-#define __NR_syscalls  (388)
+#define __NR_syscalls  (392)
 
 /*
  * *NOTE*: This is a ghost syscall private to the kernel.  Only the

arch/arm/include/uapi/asm/unistd.h

@@ -414,6 +414,8 @@
 #define __NR_memfd_create		(__NR_SYSCALL_BASE+385)
 #define __NR_bpf			(__NR_SYSCALL_BASE+386)
 #define __NR_execveat			(__NR_SYSCALL_BASE+387)
+#define __NR_userfaultfd		(__NR_SYSCALL_BASE+388)
+#define __NR_membarrier			(__NR_SYSCALL_BASE+389)
 
 /*
  * The following SWIs are ARM private.

arch/arm/kernel/calls.S

@@ -397,6 +397,8 @@
 /* 385 */	CALL(sys_memfd_create)
 		CALL(sys_bpf)
 		CALL(sys_execveat)
+		CALL(sys_userfaultfd)
+		CALL(sys_membarrier)
 #ifndef syscalls_counted
 .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
 #define syscalls_counted

arch/arm/mach-omap2/Kconfig

@@ -44,10 +44,11 @@ config SOC_OMAP5
 	select ARM_CPU_SUSPEND if PM
 	select ARM_GIC
 	select HAVE_ARM_SCU if SMP
-	select HAVE_ARM_TWD if SMP
 	select HAVE_ARM_ARCH_TIMER
 	select ARM_ERRATA_798181 if SMP
+	select OMAP_INTERCONNECT
 	select OMAP_INTERCONNECT_BARRIER
+	select PM_OPP if PM
 
 config SOC_AM33XX
 	bool "TI AM33XX"
@@ -70,10 +71,13 @@ config SOC_DRA7XX
 	select ARCH_OMAP2PLUS
 	select ARM_CPU_SUSPEND if PM
 	select ARM_GIC
+	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_ARCH_TIMER
 	select IRQ_CROSSBAR
 	select ARM_ERRATA_798181 if SMP
+	select OMAP_INTERCONNECT
 	select OMAP_INTERCONNECT_BARRIER
+	select PM_OPP if PM
 
 config ARCH_OMAP2PLUS
 	bool

arch/arm/mach-omap2/board-generic.c

@@ -20,13 +20,6 @@
 
 #include "common.h"
 
-#if !(defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3))
-#define intc_of_init	NULL
-#endif
-#ifndef CONFIG_ARCH_OMAP4
-#define gic_of_init		NULL
-#endif
-
 static const struct of_device_id omap_dt_match_table[] __initconst = {
 	{ .compatible = "simple-bus", },
 	{ .compatible = "ti,omap-infra", },

arch/arm/mach-omap2/id.c

@@ -653,8 +653,12 @@ void __init dra7xxx_check_revision(void)
 			omap_revision = DRA752_REV_ES1_0;
 			break;
 		case 1:
-		default:
 			omap_revision = DRA752_REV_ES1_1;
+			break;
+		case 2:
+		default:
+			omap_revision = DRA752_REV_ES2_0;
+			break;
 		}
 		break;
 
@@ -674,7 +678,7 @@ void __init dra7xxx_check_revision(void)
 		/* Unknown default to latest silicon rev as default*/
 		pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%x)\n",
 			__func__, idcode, hawkeye, rev);
-		omap_revision = DRA752_REV_ES1_1;
+		omap_revision = DRA752_REV_ES2_0;
 	}
 
 	sprintf(soc_name, "DRA%03x", omap_rev() >> 16);

arch/arm/mach-omap2/io.c

@@ -676,6 +676,7 @@ void __init am43xx_init_early(void)
 void __init am43xx_init_late(void)
 {
 	omap_common_late_init();
+	omap2_clk_enable_autoidle_all();
 }
 #endif
 

arch/arm/mach-omap2/omap_device.c

@@ -901,7 +901,8 @@ static int __init omap_device_late_idle(struct device *dev, void *data)
 		if (od->hwmods[i]->flags & HWMOD_INIT_NO_IDLE)
 			return 0;
 
-	if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER) {
+	if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER &&
+	    od->_driver_status != BUS_NOTIFY_BIND_DRIVER) {
 		if (od->_state == OMAP_DEVICE_STATE_ENABLED) {
 			dev_warn(dev, "%s: enabled but no driver.  Idling\n",
 				 __func__);

arch/arm/mach-omap2/pm.h

@@ -103,7 +103,8 @@ static inline void enable_omap3630_toggle_l2_on_restore(void) { }
 #define PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD	(1 << 0)
 #define PM_OMAP4_CPU_OSWR_DISABLE		(1 << 1)
 
-#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_PM) && (defined(CONFIG_ARCH_OMAP4) ||\
+	   defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX))
 extern u16 pm44xx_errata;
 #define IS_PM44XX_ERRATUM(id)		(pm44xx_errata & (id))
 #else

arch/arm/mach-omap2/soc.h

@@ -469,6 +469,8 @@ IS_OMAP_TYPE(3430, 0x3430)
 #define DRA7XX_CLASS		0x07000000
 #define DRA752_REV_ES1_0	(DRA7XX_CLASS | (0x52 << 16) | (0x10 << 8))
 #define DRA752_REV_ES1_1	(DRA7XX_CLASS | (0x52 << 16) | (0x11 << 8))
+#define DRA752_REV_ES2_0	(DRA7XX_CLASS | (0x52 << 16) | (0x20 << 8))
+#define DRA722_REV_ES1_0	(DRA7XX_CLASS | (0x22 << 16) | (0x10 << 8))
 #define DRA722_REV_ES1_0	(DRA7XX_CLASS | (0x22 << 16) | (0x10 << 8))
 
 void omap2xxx_check_revision(void);

arch/arm/mach-omap2/timer.c

@@ -297,12 +297,8 @@ static int __init omap_dm_timer_init_one(struct omap_dm_timer *timer,
 	if (IS_ERR(src))
 		return PTR_ERR(src);
 
-	r = clk_set_parent(timer->fclk, src);
-	if (r < 0) {
-		pr_warn("%s: %s cannot set source\n", __func__, oh->name);
-		clk_put(src);
-		return r;
-	}
+	WARN(clk_set_parent(timer->fclk, src) < 0,
+	     "Cannot set timer parent clock, no PLL clock driver?");
 
 	clk_put(src);
 

arch/arm/mach-omap2/vc.c

@@ -300,7 +300,7 @@ static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm)
 
 	val = voltdm->read(OMAP3_PRM_POLCTRL_OFFSET);
 	if (!(val & OMAP3430_PRM_POLCTRL_CLKREQ_POL) ||
-	    (val & OMAP3430_PRM_POLCTRL_CLKREQ_POL)) {
+	    (val & OMAP3430_PRM_POLCTRL_OFFMODE_POL)) {
 		val |= OMAP3430_PRM_POLCTRL_CLKREQ_POL;
 		val &= ~OMAP3430_PRM_POLCTRL_OFFMODE_POL;
 		pr_debug("PM: fixing sys_clkreq and sys_off_mode polarity to 0x%x\n",

arch/arm/mach-pxa/balloon3.c

@@ -502,7 +502,7 @@ static void balloon3_irq_handler(struct irq_desc *desc)
 					balloon3_irq_enabled;
 	do {
 		struct irq_data *d = irq_desc_get_irq_data(desc);
-		struct irq_chip *chip = irq_data_get_chip(d);
+		struct irq_chip *chip = irq_desc_get_chip(desc);
 		unsigned int irq;
 
 		/* clear useless edge notification */

arch/arm/mach-pxa/include/mach/addr-map.h

@@ -43,6 +43,13 @@
  * 0xf6200000..0xf6201000
  */
 
+/*
+ * DFI Bus for NAND, PXA3xx only
+ */
+#define NAND_PHYS		0x43100000
+#define NAND_VIRT		IOMEM(0xf6300000)
+#define NAND_SIZE		0x00100000
+
 /*
  * Internal Memory Controller (PXA27x and later)
  */

arch/arm/mach-pxa/pxa3xx.c

@@ -47,6 +47,13 @@ extern void __init pxa_dt_irq_init(int (*fn)(struct irq_data *, unsigned int));
 #define ISRAM_START	0x5c000000
 #define ISRAM_SIZE	SZ_256K
 
+/*
+ * NAND NFC: DFI bus arbitration subset
+ */
+#define NDCR			(*(volatile u32 __iomem*)(NAND_VIRT + 0))
+#define NDCR_ND_ARB_EN		(1 << 12)
+#define NDCR_ND_ARB_CNTL	(1 << 19)
+
 static void __iomem *sram;
 static unsigned long wakeup_src;
 
@@ -362,7 +369,12 @@ static struct map_desc pxa3xx_io_desc[] __initdata = {
 		.pfn		= __phys_to_pfn(PXA3XX_SMEMC_BASE),
 		.length		= SMEMC_SIZE,
 		.type		= MT_DEVICE
-	}
+	}, {
+		.virtual	= (unsigned long)NAND_VIRT,
+		.pfn		= __phys_to_pfn(NAND_PHYS),
+		.length		= NAND_SIZE,
+		.type		= MT_DEVICE
+	},
 };
 
 void __init pxa3xx_map_io(void)
@@ -419,6 +431,13 @@ static int __init pxa3xx_init(void)
 		 */
 		ASCR &= ~(ASCR_RDH | ASCR_D1S | ASCR_D2S | ASCR_D3S);
 
+		/*
+		 * Disable DFI bus arbitration, to prevent a system bus lock if
+		 * somebody disables the NAND clock (unused clock) while this
+		 * bit remains set.
+		 */
+		NDCR = (NDCR & ~NDCR_ND_ARB_EN) | NDCR_ND_ARB_CNTL;
+
 		if ((ret = pxa_init_dma(IRQ_DMA, 32)))
 			return ret;
 

arch/arm/mm/alignment.c

@@ -365,15 +365,21 @@ do_alignment_ldrhstrh(unsigned long addr, unsigned long instr, struct pt_regs *r
  user:
 	if (LDST_L_BIT(instr)) {
 		unsigned long val;
+		unsigned int __ua_flags = uaccess_save_and_enable();
+
 		get16t_unaligned_check(val, addr);
+		uaccess_restore(__ua_flags);
 
 		/* signed half-word? */
 		if (instr & 0x40)
 			val = (signed long)((signed short) val);
 
 		regs->uregs[rd] = val;
-	} else
+	} else {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		put16t_unaligned_check(regs->uregs[rd], addr);
+		uaccess_restore(__ua_flags);
+	}
 
 	return TYPE_LDST;
 
@@ -420,14 +426,21 @@ do_alignment_ldrdstrd(unsigned long addr, unsigned long instr,
 
  user:
 	if (load) {
-		unsigned long val;
+		unsigned long val, val2;
+		unsigned int __ua_flags = uaccess_save_and_enable();
+
 		get32t_unaligned_check(val, addr);
+		get32t_unaligned_check(val2, addr + 4);
+
+		uaccess_restore(__ua_flags);
+
 		regs->uregs[rd] = val;
-		get32t_unaligned_check(val, addr + 4);
-		regs->uregs[rd2] = val;
+		regs->uregs[rd2] = val2;
 	} else {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		put32t_unaligned_check(regs->uregs[rd], addr);
 		put32t_unaligned_check(regs->uregs[rd2], addr + 4);
+		uaccess_restore(__ua_flags);
 	}
 
 	return TYPE_LDST;
@@ -458,10 +471,15 @@ do_alignment_ldrstr(unsigned long addr, unsigned long instr, struct pt_regs *reg
  trans:
 	if (LDST_L_BIT(instr)) {
 		unsigned int val;
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		get32t_unaligned_check(val, addr);
+		uaccess_restore(__ua_flags);
 		regs->uregs[rd] = val;
-	} else
+	} else {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		put32t_unaligned_check(regs->uregs[rd], addr);
+		uaccess_restore(__ua_flags);
+	}
 	return TYPE_LDST;
 
  fault:
@@ -531,6 +549,7 @@ do_alignment_ldmstm(unsigned long addr, unsigned long instr, struct pt_regs *reg
 #endif
 
 	if (user_mode(regs)) {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		for (regbits = REGMASK_BITS(instr), rd = 0; regbits;
 		     regbits >>= 1, rd += 1)
 			if (regbits & 1) {
@@ -542,6 +561,7 @@ do_alignment_ldmstm(unsigned long addr, unsigned long instr, struct pt_regs *reg
 					put32t_unaligned_check(regs->uregs[rd], eaddr);
 				eaddr += 4;
 			}
+		uaccess_restore(__ua_flags);
 	} else {
 		for (regbits = REGMASK_BITS(instr), rd = 0; regbits;
 		     regbits >>= 1, rd += 1)

arch/arm/plat-pxa/ssp.c

@@ -107,7 +107,6 @@ static const struct of_device_id pxa_ssp_of_ids[] = {
 	{ .compatible = "mvrl,pxa168-ssp",	.data = (void *) PXA168_SSP },
 	{ .compatible = "mrvl,pxa910-ssp",	.data = (void *) PXA910_SSP },
 	{ .compatible = "mrvl,ce4100-ssp",	.data = (void *) CE4100_SSP },
-	{ .compatible = "mrvl,lpss-ssp",	.data = (void *) LPSS_SSP },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, pxa_ssp_of_ids);

arch/arm64/boot/dts/mediatek/mt8173.dtsi

@@ -81,7 +81,7 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
+			entry-method = "psci";
 
 			CPU_SLEEP_0: cpu-sleep-0 {
 				compatible = "arm,idle-state";

arch/arm64/boot/dts/rockchip/rk3368.dtsi

@@ -106,7 +106,7 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
+			entry-method = "psci";
 
 			cpu_sleep: cpu-sleep-0 {
 				compatible = "arm,idle-state";

arch/arm64/include/asm/kvm_host.h

@@ -33,6 +33,7 @@
 #define KVM_USER_MEM_SLOTS 32
 #define KVM_PRIVATE_MEM_SLOTS 4
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 #include <kvm/arm_vgic.h>
 #include <kvm/arm_arch_timer.h>

arch/arm64/include/asm/pgtable.h

@@ -79,7 +79,7 @@ extern void __pgd_error(const char *file, int line, unsigned long val);
 #define PAGE_S2			__pgprot(PROT_DEFAULT | PTE_S2_MEMATTR(MT_S2_NORMAL) | PTE_S2_RDONLY)
 #define PAGE_S2_DEVICE		__pgprot(PROT_DEFAULT | PTE_S2_MEMATTR(MT_S2_DEVICE_nGnRE) | PTE_S2_RDONLY | PTE_UXN)
 
-#define PAGE_NONE		__pgprot(((_PAGE_DEFAULT) & ~PTE_TYPE_MASK) | PTE_PROT_NONE | PTE_PXN | PTE_UXN)
+#define PAGE_NONE		__pgprot(((_PAGE_DEFAULT) & ~PTE_VALID) | PTE_PROT_NONE | PTE_PXN | PTE_UXN)
 #define PAGE_SHARED		__pgprot(_PAGE_DEFAULT | PTE_USER | PTE_NG | PTE_PXN | PTE_UXN | PTE_WRITE)
 #define PAGE_SHARED_EXEC	__pgprot(_PAGE_DEFAULT | PTE_USER | PTE_NG | PTE_PXN | PTE_WRITE)
 #define PAGE_COPY		__pgprot(_PAGE_DEFAULT | PTE_USER | PTE_NG | PTE_PXN | PTE_UXN)
@@ -496,7 +496,7 @@ static inline pud_t *pud_offset(pgd_t *pgd, unsigned long addr)
 static inline pte_t pte_modify(pte_t pte, pgprot_t newprot)
 {
 	const pteval_t mask = PTE_USER | PTE_PXN | PTE_UXN | PTE_RDONLY |
-			      PTE_PROT_NONE | PTE_WRITE | PTE_TYPE_MASK;
+			      PTE_PROT_NONE | PTE_VALID | PTE_WRITE;
 	/* preserve the hardware dirty information */
 	if (pte_hw_dirty(pte))
 		pte = pte_mkdirty(pte);

arch/arm64/kernel/efi.c

@@ -258,7 +258,8 @@ static bool __init efi_virtmap_init(void)
 		 */
 		if (!is_normal_ram(md))
 			prot = __pgprot(PROT_DEVICE_nGnRE);
-		else if (md->type == EFI_RUNTIME_SERVICES_CODE)
+		else if (md->type == EFI_RUNTIME_SERVICES_CODE ||
+			 !PAGE_ALIGNED(md->phys_addr))
 			prot = PAGE_KERNEL_EXEC;
 		else
 			prot = PAGE_KERNEL;

arch/arm64/kernel/entry-ftrace.S

@@ -178,6 +178,24 @@ ENTRY(ftrace_stub)
 ENDPROC(ftrace_stub)
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
+	/* save return value regs*/
+	.macro save_return_regs
+	sub sp, sp, #64
+	stp x0, x1, [sp]
+	stp x2, x3, [sp, #16]
+	stp x4, x5, [sp, #32]
+	stp x6, x7, [sp, #48]
+	.endm
+
+	/* restore return value regs*/
+	.macro restore_return_regs
+	ldp x0, x1, [sp]
+	ldp x2, x3, [sp, #16]
+	ldp x4, x5, [sp, #32]
+	ldp x6, x7, [sp, #48]
+	add sp, sp, #64
+	.endm
+
 /*
  * void ftrace_graph_caller(void)
  *
@@ -204,11 +222,11 @@ ENDPROC(ftrace_graph_caller)
  * only when CONFIG_HAVE_FUNCTION_GRAPH_FP_TEST is enabled.
  */
 ENTRY(return_to_handler)
-	str	x0, [sp, #-16]!
+	save_return_regs
 	mov	x0, x29			//     parent's fp
 	bl	ftrace_return_to_handler// addr = ftrace_return_to_hander(fp);
 	mov	x30, x0			// restore the original return address
-	ldr	x0, [sp], #16
+	restore_return_regs
 	ret
 END(return_to_handler)
 #endif /* CONFIG_FUNCTION_GRAPH_TRACER */

arch/avr32/include/asm/Kbuild

@@ -20,4 +20,5 @@ generic-y += sections.h
 generic-y += topology.h
 generic-y += trace_clock.h
 generic-y += vga.h
+generic-y += word-at-a-time.h
 generic-y += xor.h

arch/blackfin/include/asm/Kbuild

@@ -46,4 +46,5 @@ generic-y += types.h
 generic-y += ucontext.h
 generic-y += unaligned.h
 generic-y += user.h
+generic-y += word-at-a-time.h
 generic-y += xor.h

arch/c6x/include/asm/Kbuild

@@ -59,4 +59,5 @@ generic-y += types.h
 generic-y += ucontext.h
 generic-y += user.h
 generic-y += vga.h
+generic-y += word-at-a-time.h
 generic-y += xor.h

arch/cris/include/asm/Kbuild

@@ -43,4 +43,5 @@ generic-y += topology.h
 generic-y += trace_clock.h
 generic-y += types.h
 generic-y += vga.h
+generic-y += word-at-a-time.h
 generic-y += xor.h

arch/frv/include/asm/Kbuild

@@ -7,3 +7,4 @@ generic-y += mcs_spinlock.h
 generic-y += mm-arch-hooks.h
 generic-y += preempt.h
 generic-y += trace_clock.h
+generic-y += word-at-a-time.h

arch/frv/mb93090-mb00/pci-vdk.c

@@ -294,6 +294,8 @@ void pcibios_fixup_bus(struct pci_bus *bus)
 	printk("### PCIBIOS_FIXUP_BUS(%d)\n",bus->number);
 #endif
 
+	pci_read_bridge_bases(bus);
+
 	if (bus->number == 0) {
 		struct pci_dev *dev;
 		list_for_each_entry(dev, &bus->devices, bus_list) {

arch/hexagon/include/asm/Kbuild

@@ -58,4 +58,5 @@ generic-y += types.h
 generic-y += ucontext.h
 generic-y += unaligned.h
 generic-y += vga.h
+generic-y += word-at-a-time.h
 generic-y += xor.h

arch/ia64/include/asm/Kbuild

@@ -8,3 +8,4 @@ generic-y += mm-arch-hooks.h
 generic-y += preempt.h
 generic-y += trace_clock.h
 generic-y += vtime.h
+generic-y += word-at-a-time.h

arch/ia64/pci/pci.c

@@ -533,9 +533,10 @@ void pcibios_fixup_bus(struct pci_bus *b)
 {
 	struct pci_dev *dev;
 
-	if (b->self)
+	if (b->self) {
+		pci_read_bridge_bases(b);
 		pcibios_fixup_bridge_resources(b->self);
-
+	}
 	list_for_each_entry(dev, &b->devices, bus_list)
 		pcibios_fixup_device_resources(dev);
 	platform_pci_fixup_bus(b);

arch/m32r/include/asm/Kbuild

@@ -9,3 +9,4 @@ generic-y += module.h
 generic-y += preempt.h
 generic-y += sections.h
 generic-y += trace_clock.h
+generic-y += word-at-a-time.h

arch/m68k/configs/amiga_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -57,7 +58,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -67,10 +67,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -179,6 +181,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -206,6 +209,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -271,6 +275,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -370,6 +375,7 @@ CONFIG_ZORRO8390=y
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_SMSC is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -537,6 +543,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/apollo_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -55,7 +56,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -65,10 +65,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -177,6 +179,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -204,6 +207,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -269,6 +273,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -344,6 +349,7 @@ CONFIG_VETH=m
 # CONFIG_NET_VENDOR_SAMSUNG is not set
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -495,6 +501,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/atari_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -55,7 +56,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -65,10 +65,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -177,6 +179,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -204,6 +207,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -269,6 +273,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -355,6 +360,7 @@ CONFIG_NE2000=y
 # CONFIG_NET_VENDOR_SEEQ is not set
 CONFIG_SMC91X=y
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -517,6 +523,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/bvme6000_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -53,7 +54,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -63,10 +63,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -175,6 +177,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -202,6 +205,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -267,6 +271,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -343,6 +348,7 @@ CONFIG_BVME6000_NET=y
 # CONFIG_NET_VENDOR_SAMSUNG is not set
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -488,6 +494,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/hp300_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -55,7 +56,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -65,10 +65,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -177,6 +179,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -204,6 +207,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -269,6 +273,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -345,6 +350,7 @@ CONFIG_HPLANCE=y
 # CONFIG_NET_VENDOR_SAMSUNG is not set
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -497,6 +503,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/mac_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -54,7 +55,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -64,10 +64,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -176,6 +178,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -203,6 +206,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -271,6 +275,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -364,6 +369,7 @@ CONFIG_MAC8390=y
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_SMSC is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -519,6 +525,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/multi_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -64,7 +65,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -74,10 +74,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -186,6 +188,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -213,6 +216,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -281,6 +285,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -410,6 +415,7 @@ CONFIG_ZORRO8390=y
 # CONFIG_NET_VENDOR_SEEQ is not set
 CONFIG_SMC91X=y
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PLIP=m
@@ -599,6 +605,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/mvme147_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -52,7 +53,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -62,10 +62,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -174,6 +176,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -201,6 +204,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -266,6 +270,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -343,6 +348,7 @@ CONFIG_MVME147_NET=y
 # CONFIG_NET_VENDOR_SAMSUNG is not set
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -488,6 +494,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/mvme16x_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -53,7 +54,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -63,10 +63,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -175,6 +177,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -202,6 +205,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -267,6 +271,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -343,6 +348,7 @@ CONFIG_MVME16x_NET=y
 # CONFIG_NET_VENDOR_SAMSUNG is not set
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -488,6 +494,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/q40_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -53,7 +54,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -63,10 +63,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -175,6 +177,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -202,6 +205,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -267,6 +271,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -354,6 +359,7 @@ CONFIG_NE2000=y
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_SMSC is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PLIP=m
@@ -510,6 +516,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/configs/sun3_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -50,7 +51,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -60,10 +60,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -172,6 +174,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -199,6 +202,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -264,6 +268,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -341,6 +346,7 @@ CONFIG_SUN3_82586=y
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
 # CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -489,6 +495,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m
 CONFIG_CRYPTO_MANAGER=y

arch/m68k/configs/sun3x_defconfig

@@ -10,6 +10,7 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_USERFAULTFD=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
@@ -50,7 +51,6 @@ CONFIG_NET_IPGRE_DEMUX=m
 CONFIG_NET_IPGRE=m
 CONFIG_NET_IPVTI=m
 CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_GENEVE_CORE=m
 CONFIG_INET_AH=m
 CONFIG_INET_ESP=m
 CONFIG_INET_IPCOMP=m
@@ -60,10 +60,12 @@ CONFIG_INET_XFRM_MODE_BEET=m
 # CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=m
 CONFIG_INET_UDP_DIAG=m
+CONFIG_IPV6=m
 CONFIG_IPV6_ROUTER_PREF=y
 CONFIG_INET6_AH=m
 CONFIG_INET6_ESP=m
 CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_ILA=m
 CONFIG_IPV6_VTI=m
 CONFIG_IPV6_GRE=m
 CONFIG_NETFILTER=y
@@ -172,6 +174,7 @@ CONFIG_IP_SET_HASH_NETIFACE=m
 CONFIG_IP_SET_LIST_SET=m
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
+CONFIG_NFT_DUP_IPV4=m
 CONFIG_NF_TABLES_ARP=m
 CONFIG_NF_LOG_ARP=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
@@ -199,6 +202,7 @@ CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
+CONFIG_NFT_DUP_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_NFT_MASQ_IPV6=m
 CONFIG_NFT_REDIR_IPV6=m
@@ -264,6 +268,7 @@ CONFIG_NETLINK_DIAG=m
 CONFIG_MPLS=y
 CONFIG_NET_MPLS_GSO=m
 CONFIG_MPLS_ROUTING=m
+CONFIG_MPLS_IPTUNNEL=m
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 CONFIG_DEVTMPFS=y
@@ -341,6 +346,7 @@ CONFIG_SUN3LANCE=y
 # CONFIG_NET_VENDOR_SAMSUNG is not set
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_PPP=m
@@ -489,6 +495,7 @@ CONFIG_TEST_USER_COPY=m
 CONFIG_TEST_BPF=m
 CONFIG_TEST_FIRMWARE=m
 CONFIG_TEST_UDELAY=m
+CONFIG_TEST_STATIC_KEYS=m
 CONFIG_EARLY_PRINTK=y
 CONFIG_ENCRYPTED_KEYS=m
 CONFIG_CRYPTO_RSA=m

arch/m68k/include/asm/linkage.h

@@ -4,4 +4,34 @@
 #define __ALIGN .align 4
 #define __ALIGN_STR ".align 4"
 
+/*
+ * Make sure the compiler doesn't do anything stupid with the
+ * arguments on the stack - they are owned by the *caller*, not
+ * the callee. This just fools gcc into not spilling into them,
+ * and keeps it from doing tailcall recursion and/or using the
+ * stack slots for temporaries, since they are live and "used"
+ * all the way to the end of the function.
+ */
+#define asmlinkage_protect(n, ret, args...) \
+	__asmlinkage_protect##n(ret, ##args)
+#define __asmlinkage_protect_n(ret, args...) \
+	__asm__ __volatile__ ("" : "=r" (ret) : "0" (ret), ##args)
+#define __asmlinkage_protect0(ret) \
+	__asmlinkage_protect_n(ret)
+#define __asmlinkage_protect1(ret, arg1) \
+	__asmlinkage_protect_n(ret, "m" (arg1))
+#define __asmlinkage_protect2(ret, arg1, arg2) \
+	__asmlinkage_protect_n(ret, "m" (arg1), "m" (arg2))
+#define __asmlinkage_protect3(ret, arg1, arg2, arg3) \
+	__asmlinkage_protect_n(ret, "m" (arg1), "m" (arg2), "m" (arg3))
+#define __asmlinkage_protect4(ret, arg1, arg2, arg3, arg4) \
+	__asmlinkage_protect_n(ret, "m" (arg1), "m" (arg2), "m" (arg3), \
+			      "m" (arg4))
+#define __asmlinkage_protect5(ret, arg1, arg2, arg3, arg4, arg5) \
+	__asmlinkage_protect_n(ret, "m" (arg1), "m" (arg2), "m" (arg3), \
+			      "m" (arg4), "m" (arg5))
+#define __asmlinkage_protect6(ret, arg1, arg2, arg3, arg4, arg5, arg6) \
+	__asmlinkage_protect_n(ret, "m" (arg1), "m" (arg2), "m" (arg3), \
+			      "m" (arg4), "m" (arg5), "m" (arg6))
+
 #endif

arch/m68k/include/asm/unistd.h

@@ -4,7 +4,7 @@
 #include <uapi/asm/unistd.h>
 
 
-#define NR_syscalls		356
+#define NR_syscalls		375
 
 #define __ARCH_WANT_OLD_READDIR
 #define __ARCH_WANT_OLD_STAT

arch/m68k/include/uapi/asm/unistd.h

@@ -361,5 +361,24 @@
 #define __NR_memfd_create	353
 #define __NR_bpf		354
 #define __NR_execveat		355
+#define __NR_socket		356
+#define __NR_socketpair		357
+#define __NR_bind		358
+#define __NR_connect		359
+#define __NR_listen		360
+#define __NR_accept4		361
+#define __NR_getsockopt		362
+#define __NR_setsockopt		363
+#define __NR_getsockname	364
+#define __NR_getpeername	365
+#define __NR_sendto		366
+#define __NR_sendmsg		367
+#define __NR_recvfrom		368
+#define __NR_recvmsg		369
+#define __NR_shutdown		370
+#define __NR_recvmmsg		371
+#define __NR_sendmmsg		372
+#define __NR_userfaultfd	373
+#define __NR_membarrier		374
 
 #endif /* _UAPI_ASM_M68K_UNISTD_H_ */

arch/m68k/kernel/syscalltable.S

@@ -376,4 +376,22 @@ ENTRY(sys_call_table)
 	.long sys_memfd_create
 	.long sys_bpf
 	.long sys_execveat		/* 355 */
-
+	.long sys_socket
+	.long sys_socketpair
+	.long sys_bind
+	.long sys_connect
+	.long sys_listen		/* 360 */
+	.long sys_accept4
+	.long sys_getsockopt
+	.long sys_setsockopt
+	.long sys_getsockname
+	.long sys_getpeername		/* 365 */
+	.long sys_sendto
+	.long sys_sendmsg
+	.long sys_recvfrom
+	.long sys_recvmsg
+	.long sys_shutdown		/* 370 */
+	.long sys_recvmmsg
+	.long sys_sendmmsg
+	.long sys_userfaultfd
+	.long sys_membarrier

arch/metag/include/asm/Kbuild

@@ -54,4 +54,5 @@ generic-y += ucontext.h
 generic-y += unaligned.h
 generic-y += user.h
 generic-y += vga.h
+generic-y += word-at-a-time.h
 generic-y += xor.h

arch/microblaze/include/asm/Kbuild

@@ -10,3 +10,4 @@ generic-y += mm-arch-hooks.h
 generic-y += preempt.h
 generic-y += syscalls.h
 generic-y += trace_clock.h
+generic-y += word-at-a-time.h

arch/microblaze/pci/pci-common.c

@@ -863,7 +863,14 @@ void pcibios_setup_bus_devices(struct pci_bus *bus)
 
 void pcibios_fixup_bus(struct pci_bus *bus)
 {
-	/* Fixup the bus */
+	/* When called from the generic PCI probe, read PCI<->PCI bridge
+	 * bases. This is -not- called when generating the PCI tree from
+	 * the OF device-tree.
+	 */
+	if (bus->self != NULL)
+		pci_read_bridge_bases(bus);
+
+	/* Now fixup the bus bus */
 	pcibios_setup_bus_self(bus);
 
 	/* Now fixup devices on that bus */

arch/mips/ath79/irq.c

@@ -293,8 +293,26 @@ static int __init ath79_misc_intc_of_init(
 
 	return 0;
 }
-IRQCHIP_DECLARE(ath79_misc_intc, "qca,ar7100-misc-intc",
-		ath79_misc_intc_of_init);
+
+static int __init ar7100_misc_intc_of_init(
+	struct device_node *node, struct device_node *parent)
+{
+	ath79_misc_irq_chip.irq_mask_ack = ar71xx_misc_irq_mask;
+	return ath79_misc_intc_of_init(node, parent);
+}
+
+IRQCHIP_DECLARE(ar7100_misc_intc, "qca,ar7100-misc-intc",
+		ar7100_misc_intc_of_init);
+
+static int __init ar7240_misc_intc_of_init(
+	struct device_node *node, struct device_node *parent)
+{
+	ath79_misc_irq_chip.irq_ack = ar724x_misc_irq_ack;
+	return ath79_misc_intc_of_init(node, parent);
+}
+
+IRQCHIP_DECLARE(ar7240_misc_intc, "qca,ar7240-misc-intc",
+		ar7240_misc_intc_of_init);
 
 static int __init ar79_cpu_intc_of_init(
 	struct device_node *node, struct device_node *parent)

arch/mips/cavium-octeon/setup.c

@@ -933,7 +933,7 @@ void __init plat_mem_setup(void)
 	while ((boot_mem_map.nr_map < BOOT_MEM_MAP_MAX)
 		&& (total < MAX_MEMORY)) {
 		memory = cvmx_bootmem_phy_alloc(mem_alloc_size,
-						__pa_symbol(&__init_end), -1,
+						__pa_symbol(&_end), -1,
 						0x100000,
 						CVMX_BOOTMEM_FLAG_NO_LOCKING);
 		if (memory >= 0) {

arch/mips/include/asm/Kbuild

@@ -17,4 +17,5 @@ generic-y += segment.h
 generic-y += serial.h
 generic-y += trace_clock.h
 generic-y += user.h
+generic-y += word-at-a-time.h
 generic-y += xor.h

arch/mips/include/asm/cpu-features.h

@@ -20,6 +20,9 @@
 #ifndef cpu_has_tlb
 #define cpu_has_tlb		(cpu_data[0].options & MIPS_CPU_TLB)
 #endif
+#ifndef cpu_has_ftlb
+#define cpu_has_ftlb		(cpu_data[0].options & MIPS_CPU_FTLB)
+#endif
 #ifndef cpu_has_tlbinv
 #define cpu_has_tlbinv		(cpu_data[0].options & MIPS_CPU_TLBINV)
 #endif

arch/mips/include/asm/cpu.h

@@ -385,6 +385,7 @@ enum cpu_type_enum {
 #define MIPS_CPU_CDMM		0x4000000000ull	/* CPU has Common Device Memory Map */
 #define MIPS_CPU_BP_GHIST	0x8000000000ull /* R12K+ Branch Prediction Global History */
 #define MIPS_CPU_SP		0x10000000000ull /* Small (1KB) page support */
+#define MIPS_CPU_FTLB		0x20000000000ull /* CPU has Fixed-page-size TLB */
 
 /*
  * CPU ASE encodings

arch/mips/include/asm/kvm_host.h

@@ -61,6 +61,7 @@
 #define KVM_PRIVATE_MEM_SLOTS 	0
 
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
+#define KVM_HALT_POLL_NS_DEFAULT 500000