Merge tag 'v4.2-rc4' into devel

Linux 4.2-rc4

.mailmap

@@ -116,6 +116,7 @@ Shiraz Hashim <shiraz.linux.kernel@gmail.com> <shiraz.hashim@st.com>
 Simon Kelley <simon@thekelleys.org.uk>
 Stéphane Witzmann <stephane.witzmann@ubpmes.univ-bpclermont.fr>
 Stephen Hemminger <shemminger@osdl.org>
+Sudeep Holla <sudeep.holla@arm.com> Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
 Sumit Semwal <sumit.semwal@ti.com>
 Tejun Heo <htejun@gmail.com>
 Thomas Graf <tgraf@suug.ch>
@@ -125,7 +126,9 @@ Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
 Uwe Kleine-König <ukl@pengutronix.de>
 Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
 Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
-Viresh Kumar <viresh.linux@gmail.com> <viresh.kumar@st.com>
+Viresh Kumar <vireshk@kernel.org> <viresh.kumar@st.com>
+Viresh Kumar <vireshk@kernel.org> <viresh.linux@gmail.com>
+Viresh Kumar <vireshk@kernel.org> <viresh.kumar2@arm.com>
 Takashi YOSHII <takashi.yoshii.zj@renesas.com>
 Yusuke Goda <goda.yusuke@renesas.com>
 Gustavo Padovan <gustavo@las.ic.unicamp.br>

Documentation/ABI/testing/sysfs-bus-iio

@@ -1234,10 +1234,8 @@ Description:
 		object is near the sensor, usually be observing
 		reflectivity of infrared or ultrasound emitted.
 		Often these sensors are unit less and as such conversion
-		to SI units is not possible.  Where it is, the units should
-		be meters.  If such a conversion is not possible, the reported
-		values should behave in the same way as a distance, i.e. lower
-		values indicate something is closer to the sensor.
+		to SI units is not possible. Higher proximity measurements
+		indicate closer objects, and vice versa.
 
 What:		/sys/.../iio:deviceX/in_illuminance_input
 What:		/sys/.../iio:deviceX/in_illuminance_raw

Documentation/DocBook/drm.tmpl

@@ -3383,7 +3383,7 @@ void intel_crt_init(struct drm_device *dev)
 	<td valign="top" >TBD</td>
 	</tr>
 	<tr>
-	<td rowspan="2" valign="top" >omap</td>
+	<td valign="top" >omap</td>
 	<td valign="top" >Generic</td>
 	<td valign="top" >“zorder”</td>
 	<td valign="top" >RANGE</td>

Documentation/arm/SPEAr/overview.txt

@@ -60,4 +60,4 @@ Introduction
   Document Author
   ---------------
 
-  Viresh Kumar <viresh.linux@gmail.com>, (c) 2010-2012 ST Microelectronics
+  Viresh Kumar <vireshk@kernel.org>, (c) 2010-2012 ST Microelectronics

Documentation/device-mapper/cache.txt

@@ -258,6 +258,12 @@ cache metadata mode      : ro if read-only, rw if read-write
 	no further I/O will be permitted and the status will just
 	contain the string 'Fail'.  The userspace recovery tools
 	should then be used.
+needs_check		 : 'needs_check' if set, '-' if not set
+	A metadata operation has failed, resulting in the needs_check
+	flag being set in the metadata's superblock.  The metadata
+	device must be deactivated and checked/repaired before the
+	cache can be made fully operational again.  '-' indicates
+	needs_check is not set.
 
 Messages
 --------

Documentation/device-mapper/thin-provisioning.txt

@@ -296,7 +296,7 @@ ii) Status
 	underlying device.  When this is enabled when loading the table,
 	it can get disabled if the underlying device doesn't support it.
 
-    ro|rw
+    ro|rw|out_of_data_space
 	If the pool encounters certain types of device failures it will
 	drop into a read-only metadata mode in which no changes to
 	the pool metadata (like allocating new blocks) are permitted.
@@ -314,6 +314,13 @@ ii) Status
 	module parameter can be used to change this timeout -- it
 	defaults to 60 seconds but may be disabled using a value of 0.
 
+    needs_check
+	A metadata operation has failed, resulting in the needs_check
+	flag being set in the metadata's superblock.  The metadata
+	device must be deactivated and checked/repaired before the
+	thin-pool can be made fully operational again.  '-' indicates
+	needs_check is not set.
+
 iii) Messages
 
     create_thin <dev id>

Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt

@@ -65,8 +65,10 @@ Optional properties:
 - edid: verbatim EDID data block describing attached display.
 - ddc: phandle describing the i2c bus handling the display data
   channel
-- port: A port node with endpoint definitions as defined in
+- port@[0-1]: Port nodes with endpoint definitions as defined in
   Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Port 0 is the input port connected to the IPU display interface,
+  port 1 is the output port connected to a panel.
 
 example:
 
@@ -75,9 +77,29 @@ display@di0 {
 	edid = [edid-data];
 	interface-pix-fmt = "rgb24";
 
-	port {
+	port@0 {
+		reg = <0>;
+
 		display_in: endpoint {
 			remote-endpoint = <&ipu_di0_disp0>;
 		};
 	};
+
+	port@1 {
+		reg = <1>;
+
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+panel {
+	...
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&display_out>;
+		};
+	};
 };

Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt

@@ -35,3 +35,6 @@ the PCIe specification.
 
                       NOTE: this only applies to the SMMU itself, not
                       masters connected upstream of the SMMU.
+
+- hisilicon,broken-prefetch-cmd
+                    : Avoid sending CMD_PREFETCH_* commands to the SMMU.

Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt

@@ -17,7 +17,6 @@ Required properties:
 	       "fsl,imx6sx-usdhc"
 
 Optional properties:
-- fsl,cd-controller : Indicate to use controller internal card detection
 - fsl,wp-controller : Indicate to use controller internal write protection
 - fsl,delay-line : Specify the number of delay cells for override mode.
   This is used to set the clock delay for DLL(Delay Line) on override mode
@@ -35,7 +34,6 @@ esdhc@70004000 {
 	compatible = "fsl,imx51-esdhc";
 	reg = <0x70004000 0x4000>;
 	interrupts = <1>;
-	fsl,cd-controller;
 	fsl,wp-controller;
 };
 

Documentation/kbuild/makefiles.txt

@@ -952,6 +952,14 @@ When kbuild executes, the following steps are followed (roughly):
 	$(KBUILD_ARFLAGS) set by the top level Makefile to "D" (deterministic
 	mode) if this option is supported by $(AR).
 
+    ARCH_CPPFLAGS, ARCH_AFLAGS, ARCH_CFLAGS   Overrides the kbuild defaults
+
+	These variables are appended to the KBUILD_CPPFLAGS,
+	KBUILD_AFLAGS, and KBUILD_CFLAGS, respectively, after the
+	top-level Makefile has set any other flags. This provides a
+	means for an architecture to override the defaults.
+
+
 --- 6.2 Add prerequisites to archheaders:
 
 	The archheaders: rule is used to generate header files that

MAINTAINERS

@@ -361,11 +361,11 @@ S:	Supported
 F:	drivers/input/touchscreen/ad7879.c
 
 ADDRESS SPACE LAYOUT RANDOMIZATION (ASLR)
-M:	Jiri Kosina <jkosina@suse.cz>
+M:	Jiri Kosina <jkosina@suse.com>
 S:	Maintained
 
 ADM1025 HARDWARE MONITOR DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/adm1025
@@ -430,7 +430,7 @@ S:	Maintained
 F:	drivers/macintosh/therm_adt746x.c
 
 ADT7475 HARDWARE MONITOR DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/adt7475
@@ -445,7 +445,7 @@ F:	drivers/input/misc/adxl34x.c
 
 ADVANSYS SCSI DRIVER
 M:	Matthew Wilcox <matthew@wil.cx>
-M:	Hannes Reinecke <hare@suse.de>
+M:	Hannes Reinecke <hare@suse.com>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	Documentation/scsi/advansys.txt
@@ -506,7 +506,7 @@ F:	drivers/scsi/aha152x*
 F:	drivers/scsi/pcmcia/aha152x*
 
 AIC7XXX / AIC79XX SCSI DRIVER
-M:	Hannes Reinecke <hare@suse.de>
+M:	Hannes Reinecke <hare@suse.com>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/aic7xxx/
@@ -746,7 +746,7 @@ S:	Maintained
 F:	sound/aoa/
 
 APM DRIVER
-M:	Jiri Kosina <jkosina@suse.cz>
+M:	Jiri Kosina <jkosina@suse.com>
 S:	Odd fixes
 F:	arch/x86/kernel/apm_32.c
 F:	include/linux/apm_bios.h
@@ -1001,6 +1001,7 @@ ARM/CONEXANT DIGICOLOR MACHINE SUPPORT
 M:	Baruch Siach <baruch@tkos.co.il>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
+F:	arch/arm/boot/dts/cx92755*
 N:	digicolor
 
 ARM/EBSA110 MACHINE SUPPORT
@@ -1324,7 +1325,7 @@ F:	arch/arm/mach-pxa/include/mach/palmtc.h
 F:	arch/arm/mach-pxa/palmtc.c
 
 ARM/PALM TREO SUPPORT
-M:	Tomas Cech <sleep_walker@suse.cz>
+M:	Tomas Cech <sleep_walker@suse.com>
 L:	linux-arm-kernel@lists.infradead.org
 W:	http://hackndev.com
 S:	Maintained
@@ -2405,7 +2406,7 @@ F:	drivers/gpio/gpio-bt8xx.c
 BTRFS FILE SYSTEM
 M:	Chris Mason <clm@fb.com>
 M:	Josef Bacik <jbacik@fb.com>
-M:	David Sterba <dsterba@suse.cz>
+M:	David Sterba <dsterba@suse.com>
 L:	linux-btrfs@vger.kernel.org
 W:	http://btrfs.wiki.kernel.org/
 Q:	http://patchwork.kernel.org/project/linux-btrfs/list/
@@ -2748,7 +2749,7 @@ COCCINELLE/Semantic Patches (SmPL)
 M:	Julia Lawall <Julia.Lawall@lip6.fr>
 M:	Gilles Muller <Gilles.Muller@lip6.fr>
 M:	Nicolas Palix <nicolas.palix@imag.fr>
-M:	Michal Marek <mmarek@suse.cz>
+M:	Michal Marek <mmarek@suse.com>
 L:	cocci@systeme.lip6.fr (moderated for non-subscribers)
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild.git misc
 W:	http://coccinelle.lip6.fr/
@@ -2864,7 +2865,7 @@ F:	kernel/cpuset.c
 
 CONTROL GROUP - MEMORY RESOURCE CONTROLLER (MEMCG)
 M:	Johannes Weiner <hannes@cmpxchg.org>
-M:	Michal Hocko <mhocko@suse.cz>
+M:	Michal Hocko <mhocko@kernel.org>
 L:	cgroups@vger.kernel.org
 L:	linux-mm@kvack.org
 S:	Maintained
@@ -2945,7 +2946,7 @@ F:	arch/x86/kernel/cpuid.c
 F:	arch/x86/kernel/msr.c
 
 CPU POWER MONITORING SUBSYSTEM
-M:	Thomas Renninger <trenn@suse.de>
+M:	Thomas Renninger <trenn@suse.com>
 L:	linux-pm@vger.kernel.org
 S:	Maintained
 F:	tools/power/cpupower/
@@ -3175,7 +3176,7 @@ F:	Documentation/networking/dmfe.txt
 F:	drivers/net/ethernet/dec/tulip/dmfe.c
 
 DC390/AM53C974 SCSI driver
-M:	Hannes Reinecke <hare@suse.de>
+M:	Hannes Reinecke <hare@suse.com>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/am53c974.c
@@ -3379,7 +3380,7 @@ W:	http://www.win.tue.nl/~aeb/partitions/partition_types-1.html
 S:	Maintained
 
 DISKQUOTA
-M:	Jan Kara <jack@suse.cz>
+M:	Jan Kara <jack@suse.com>
 S:	Maintained
 F:	Documentation/filesystems/quota.txt
 F:	fs/quota/
@@ -3435,7 +3436,7 @@ F:	Documentation/hwmon/dme1737
 F:	drivers/hwmon/dme1737.c
 
 DMI/SMBIOS SUPPORT
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 S:	Maintained
 T:	quilt http://jdelvare.nerim.net/devel/linux/jdelvare-dmi/
 F:	Documentation/ABI/testing/sysfs-firmware-dmi-tables
@@ -4051,7 +4052,7 @@ F:	drivers/of/of_mdio.c
 F:	drivers/of/of_net.c
 
 EXT2 FILE SYSTEM
-M:	Jan Kara <jack@suse.cz>
+M:	Jan Kara <jack@suse.com>
 L:	linux-ext4@vger.kernel.org
 S:	Maintained
 F:	Documentation/filesystems/ext2.txt
@@ -4059,7 +4060,7 @@ F:	fs/ext2/
 F:	include/linux/ext2*
 
 EXT3 FILE SYSTEM
-M:	Jan Kara <jack@suse.cz>
+M:	Jan Kara <jack@suse.com>
 M:	Andrew Morton <akpm@linux-foundation.org>
 M:	Andreas Dilger <adilger.kernel@dilger.ca>
 L:	linux-ext4@vger.kernel.org
@@ -4109,7 +4110,7 @@ F:	drivers/video/fbdev/exynos/exynos_mipi*
 F:	include/video/exynos_mipi*
 
 F71805F HARDWARE MONITORING DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/f71805f
@@ -4244,7 +4245,7 @@ S:	Maintained
 F:	drivers/block/rsxx/
 
 FLOPPY DRIVER
-M:	Jiri Kosina <jkosina@suse.cz>
+M:	Jiri Kosina <jkosina@suse.com>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/floppy.git
 S:	Odd fixes
 F:	drivers/block/floppy.c
@@ -4665,7 +4666,7 @@ F:	drivers/media/usb/stk1160/
 
 H8/300 ARCHITECTURE
 M:	Yoshinori Sato <ysato@users.sourceforge.jp>
-L:	uclinux-h8-devel@lists.sourceforge.jp
+L:	uclinux-h8-devel@lists.sourceforge.jp (moderated for non-subscribers)
 W:	http://uclinux-h8.sourceforge.jp
 T:	git git://git.sourceforge.jp/gitroot/uclinux-h8/linux.git
 S:	Maintained
@@ -4712,7 +4713,7 @@ S:	Maintained
 F:	drivers/media/usb/hackrf/
 
 HARDWARE MONITORING
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 M:	Guenter Roeck <linux@roeck-us.net>
 L:	lm-sensors@lm-sensors.org
 W:	http://www.lm-sensors.org/
@@ -4815,7 +4816,7 @@ F:	include/linux/pm.h
 F:	arch/*/include/asm/suspend*.h
 
 HID CORE LAYER
-M:	Jiri Kosina <jkosina@suse.cz>
+M:	Jiri Kosina <jkosina@suse.com>
 L:	linux-input@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid.git
 S:	Maintained
@@ -4824,7 +4825,7 @@ F:	include/linux/hid*
 F:	include/uapi/linux/hid*
 
 HID SENSOR HUB DRIVERS
-M:	Jiri Kosina <jkosina@suse.cz>
+M:	Jiri Kosina <jkosina@suse.com>
 M:	Jonathan Cameron <jic23@kernel.org>
 M:	Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
 L:	linux-input@vger.kernel.org
@@ -4958,7 +4959,7 @@ F:	include/linux/hyperv.h
 F:	tools/hv/
 
 I2C OVER PARALLEL PORT
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	Documentation/i2c/busses/i2c-parport
@@ -4967,7 +4968,7 @@ F:	drivers/i2c/busses/i2c-parport.c
 F:	drivers/i2c/busses/i2c-parport-light.c
 
 I2C/SMBUS CONTROLLER DRIVERS FOR PC
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	Documentation/i2c/busses/i2c-ali1535
@@ -5008,7 +5009,7 @@ F:	drivers/i2c/busses/i2c-ismt.c
 F:	Documentation/i2c/busses/i2c-ismt
 
 I2C/SMBUS STUB DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	drivers/i2c/i2c-stub.c
@@ -5035,7 +5036,7 @@ L:	linux-acpi@vger.kernel.org
 S:	Maintained
 
 I2C-TAOS-EVM DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	Documentation/i2c/busses/i2c-taos-evm
@@ -5564,8 +5565,8 @@ F:	include/uapi/linux/ip_vs.h
 F:	net/netfilter/ipvs/
 
 IPWIRELESS DRIVER
-M:	Jiri Kosina <jkosina@suse.cz>
-M:	David Sterba <dsterba@suse.cz>
+M:	Jiri Kosina <jkosina@suse.com>
+M:	David Sterba <dsterba@suse.com>
 S:	Odd Fixes
 F:	drivers/tty/ipwireless/
 
@@ -5685,7 +5686,7 @@ S:	Maintained
 F:	drivers/isdn/hardware/eicon/
 
 IT87 HARDWARE MONITORING DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/it87
@@ -5752,7 +5753,7 @@ F:	include/uapi/linux/jffs2.h
 
 JOURNALLING LAYER FOR BLOCK DEVICES (JBD)
 M:	Andrew Morton <akpm@linux-foundation.org>
-M:	Jan Kara <jack@suse.cz>
+M:	Jan Kara <jack@suse.com>
 L:	linux-ext4@vger.kernel.org
 S:	Maintained
 F:	fs/jbd/
@@ -5816,7 +5817,7 @@ S:	Maintained
 F:	fs/autofs4/
 
 KERNEL BUILD + files below scripts/ (unless maintained elsewhere)
-M:	Michal Marek <mmarek@suse.cz>
+M:	Michal Marek <mmarek@suse.com>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild.git for-next
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild.git rc-fixes
 L:	linux-kbuild@vger.kernel.org
@@ -5880,7 +5881,7 @@ F:	arch/x86/include/asm/svm.h
 F:	arch/x86/kvm/svm.c
 
 KERNEL VIRTUAL MACHINE (KVM) FOR POWERPC
-M:	Alexander Graf <agraf@suse.de>
+M:	Alexander Graf <agraf@suse.com>
 L:	kvm-ppc@vger.kernel.org
 W:	http://kvm.qumranet.com
 T:	git git://github.com/agraf/linux-2.6.git
@@ -5898,7 +5899,6 @@ S:	Supported
 F:	Documentation/s390/kvm.txt
 F:	arch/s390/include/asm/kvm*
 F:	arch/s390/kvm/
-F:	drivers/s390/kvm/
 
 KERNEL VIRTUAL MACHINE (KVM) FOR ARM
 M:	Christoffer Dall <christoffer.dall@linaro.org>
@@ -6037,7 +6037,7 @@ F:	drivers/leds/
 F:	include/linux/leds.h
 
 LEGACY EEPROM DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 S:	Maintained
 F:	Documentation/misc-devices/eeprom
 F:	drivers/misc/eeprom/eeprom.c
@@ -6090,7 +6090,7 @@ F:	include/linux/ata.h
 F:	include/linux/libata.h
 
 LIBATA PATA ARASAN COMPACT FLASH CONTROLLER
-M:	Viresh Kumar <viresh.linux@gmail.com>
+M:	Viresh Kumar <vireshk@kernel.org>
 L:	linux-ide@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata.git
 S:	Maintained
@@ -6251,8 +6251,8 @@ F:	drivers/platform/x86/hp_accel.c
 LIVE PATCHING
 M:	Josh Poimboeuf <jpoimboe@redhat.com>
 M:	Seth Jennings <sjenning@redhat.com>
-M:	Jiri Kosina <jkosina@suse.cz>
-M:	Vojtech Pavlik <vojtech@suse.cz>
+M:	Jiri Kosina <jkosina@suse.com>
+M:	Vojtech Pavlik <vojtech@suse.com>
 S:	Maintained
 F:	kernel/livepatch/
 F:	include/linux/livepatch.h
@@ -6278,21 +6278,21 @@ S:	Maintained
 F:	drivers/hwmon/lm73.c
 
 LM78 HARDWARE MONITOR DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/lm78
 F:	drivers/hwmon/lm78.c
 
 LM83 HARDWARE MONITOR DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/lm83
 F:	drivers/hwmon/lm83.c
 
 LM90 HARDWARE MONITOR DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/lm90
@@ -6838,6 +6838,12 @@ T:	git git://linuxtv.org/anttip/media_tree.git
 S:	Maintained
 F:	drivers/media/usb/msi2500/
 
+MSYSTEMS DISKONCHIP G3 MTD DRIVER
+M:	Robert Jarzmik <robert.jarzmik@free.fr>
+L:	linux-mtd@lists.infradead.org
+S:	Maintained
+F:	drivers/mtd/devices/docg3*
+
 MT9M032 APTINA SENSOR DRIVER
 M:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
 L:	linux-media@vger.kernel.org
@@ -7019,6 +7025,7 @@ F:	include/uapi/linux/netfilter/
 F:	net/*/netfilter.c
 F:	net/*/netfilter/
 F:	net/netfilter/
+F:	net/bridge/br_netfilter*.c
 
 NETLABEL
 M:	Paul Moore <paul@paul-moore.com>
@@ -7718,7 +7725,7 @@ S:	Maintained
 F:	drivers/char/pc8736x_gpio.c
 
 PC87427 HARDWARE MONITORING DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/pc87427
@@ -7995,7 +8002,7 @@ S:	Maintained
 F:	drivers/pinctrl/samsung/
 
 PIN CONTROLLER - ST SPEAR
-M:	Viresh Kumar <viresh.linux@gmail.com>
+M:	Viresh Kumar <vireshk@kernel.org>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.st.com/spear
@@ -8003,7 +8010,7 @@ S:	Maintained
 F:	drivers/pinctrl/spear/
 
 PKTCDVD DRIVER
-M:	Jiri Kosina <jkosina@suse.cz>
+M:	Jiri Kosina <jkosina@suse.com>
 S:	Maintained
 F:	drivers/block/pktcdvd.c
 F:	include/linux/pktcdvd.h
@@ -8894,7 +8901,7 @@ S:	Maintained
 F:	drivers/tty/serial/
 
 SYNOPSYS DESIGNWARE DMAC DRIVER
-M:	Viresh Kumar <viresh.linux@gmail.com>
+M:	Viresh Kumar <vireshk@kernel.org>
 M:	Andy Shevchenko <andriy.shevchenko@linux.intel.com>
 S:	Maintained
 F:	include/linux/dma/dw.h
@@ -9061,7 +9068,7 @@ S:	Maintained
 F:	drivers/mmc/host/sdhci-s3c*
 
 SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) ST SPEAR DRIVER
-M:	Viresh Kumar <viresh.linux@gmail.com>
+M:	Viresh Kumar <vireshk@kernel.org>
 L:	spear-devel@list.st.com
 L:	linux-mmc@vger.kernel.org
 S:	Maintained
@@ -9423,7 +9430,7 @@ F:	Documentation/hwmon/sch5627
 F:	drivers/hwmon/sch5627.c
 
 SMSC47B397 HARDWARE MONITOR DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/smsc47b397
@@ -9472,7 +9479,7 @@ S:	Supported
 F:	drivers/media/pci/solo6x10/
 
 SOFTWARE RAID (Multiple Disks) SUPPORT
-M:	Neil Brown <neilb@suse.de>
+M:	Neil Brown <neilb@suse.com>
 L:	linux-raid@vger.kernel.org
 S:	Supported
 F:	drivers/md/
@@ -9515,7 +9522,7 @@ F:	drivers/memstick/core/ms_block.*
 
 SOUND
 M:	Jaroslav Kysela <perex@perex.cz>
-M:	Takashi Iwai <tiwai@suse.de>
+M:	Takashi Iwai <tiwai@suse.com>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 W:	http://www.alsa-project.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git
@@ -9599,7 +9606,7 @@ S:	Maintained
 F:	include/linux/compiler.h
 
 SPEAR PLATFORM SUPPORT
-M:	Viresh Kumar <viresh.linux@gmail.com>
+M:	Viresh Kumar <vireshk@kernel.org>
 M:	Shiraz Hashim <shiraz.linux.kernel@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -9608,7 +9615,7 @@ S:	Maintained
 F:	arch/arm/mach-spear/
 
 SPEAR CLOCK FRAMEWORK SUPPORT
-M:	Viresh Kumar <viresh.linux@gmail.com>
+M:	Viresh Kumar <vireshk@kernel.org>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.st.com/spear
@@ -10398,7 +10405,7 @@ K:	^Subject:.*(?i)trivial
 
 TTY LAYER
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-M:	Jiri Slaby <jslaby@suse.cz>
+M:	Jiri Slaby <jslaby@suse.com>
 S:	Supported
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git
 F:	Documentation/serial/
@@ -10472,7 +10479,7 @@ F:	arch/m68k/*/*_no.*
 F:	arch/m68k/include/asm/*_no.*
 
 UDF FILESYSTEM
-M:	Jan Kara <jack@suse.cz>
+M:	Jan Kara <jack@suse.com>
 S:	Maintained
 F:	Documentation/filesystems/udf.txt
 F:	fs/udf/
@@ -10615,7 +10622,7 @@ F:	drivers/usb/gadget/
 F:	include/linux/usb/gadget*
 
 USB HID/HIDBP DRIVERS (USB KEYBOARDS, MICE, REMOTE CONTROLS, ...)
-M:	Jiri Kosina <jkosina@suse.cz>
+M:	Jiri Kosina <jkosina@suse.com>
 L:	linux-usb@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid.git
 S:	Maintained
@@ -10740,7 +10747,7 @@ S:	Maintained
 F:	drivers/usb/host/uhci*
 
 USB "USBNET" DRIVER FRAMEWORK
-M:	Oliver Neukum <oneukum@suse.de>
+M:	Oliver Neukum <oneukum@suse.com>
 L:	netdev@vger.kernel.org
 W:	http://www.linux-usb.org/usbnet
 S:	Maintained
@@ -10894,6 +10901,15 @@ F:	drivers/block/virtio_blk.c
 F:	include/linux/virtio_*.h
 F:	include/uapi/linux/virtio_*.h
 
+VIRTIO DRIVERS FOR S390
+M:	Christian Borntraeger <borntraeger@de.ibm.com>
+M:	Cornelia Huck <cornelia.huck@de.ibm.com>
+L:	linux-s390@vger.kernel.org
+L:	virtualization@lists.linux-foundation.org
+L:	kvm@vger.kernel.org
+S:	Supported
+F:	drivers/s390/virtio/
+
 VIRTIO GPU DRIVER
 M:	David Airlie <airlied@linux.ie>
 M:	Gerd Hoffmann <kraxel@redhat.com>
@@ -11067,7 +11083,7 @@ F:	Documentation/hwmon/w83793
 F:	drivers/hwmon/w83793.c
 
 W83795 HARDWARE MONITORING DRIVER
-M:	Jean Delvare <jdelvare@suse.de>
+M:	Jean Delvare <jdelvare@suse.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	drivers/hwmon/w83795.c

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 2
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc4
 NAME = Hurr durr I'ma sheep
 
 # *DOCUMENTATION*
@@ -780,10 +780,11 @@ endif
 include scripts/Makefile.kasan
 include scripts/Makefile.extrawarn
 
-# Add user supplied CPPFLAGS, AFLAGS and CFLAGS as the last assignments
-KBUILD_CPPFLAGS += $(KCPPFLAGS)
-KBUILD_AFLAGS += $(KAFLAGS)
-KBUILD_CFLAGS += $(KCFLAGS)
+# Add any arch overrides and user supplied CPPFLAGS, AFLAGS and CFLAGS as the
+# last assignments
+KBUILD_CPPFLAGS += $(ARCH_CPPFLAGS) $(KCPPFLAGS)
+KBUILD_AFLAGS   += $(ARCH_AFLAGS)   $(KAFLAGS)
+KBUILD_CFLAGS   += $(ARCH_CFLAGS)   $(KCFLAGS)
 
 # Use --build-id when available.
 LDFLAGS_BUILD_ID = $(patsubst -Wl$(comma)%,%,\

arch/Kconfig

@@ -221,6 +221,10 @@ config ARCH_TASK_STRUCT_ALLOCATOR
 config ARCH_THREAD_INFO_ALLOCATOR
 	bool
 
+# Select if arch wants to size task_struct dynamically via arch_task_struct_size:
+config ARCH_WANTS_DYNAMIC_TASK_STRUCT
+	bool
+
 config HAVE_REGS_AND_STACK_ACCESS_API
 	bool
 	help

arch/alpha/include/asm/Kbuild

@@ -5,6 +5,7 @@ generic-y += cputime.h
 generic-y += exec.h
 generic-y += irq_work.h
 generic-y += mcs_spinlock.h
+generic-y += mm-arch-hooks.h
 generic-y += preempt.h
 generic-y += sections.h
 generic-y += trace_clock.h

arch/alpha/include/asm/mm-arch-hooks.h

@@ -1,15 +0,0 @@
-/*
- * Architecture specific mm hooks
- *
- * Copyright (C) 2015, IBM Corporation
- * Author: Laurent Dufour <ldufour@linux.vnet.ibm.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef _ASM_ALPHA_MM_ARCH_HOOKS_H
-#define _ASM_ALPHA_MM_ARCH_HOOKS_H
-
-#endif /* _ASM_ALPHA_MM_ARCH_HOOKS_H */

arch/arc/Kconfig

@@ -115,6 +115,7 @@ if ISA_ARCOMPACT
 
 config ARC_CPU_750D
 	bool "ARC750D"
+	select ARC_CANT_LLSC
 	help
 	  Support for ARC750 core
 
@@ -362,7 +363,7 @@ config ARC_CANT_LLSC
 config ARC_HAS_LLSC
 	bool "Insn: LLOCK/SCOND (efficient atomic ops)"
 	default y
-	depends on !ARC_CPU_750D && !ARC_CANT_LLSC
+	depends on !ARC_CANT_LLSC
 
 config ARC_HAS_SWAPE
 	bool "Insn: SWAPE (endian-swap)"

arch/arc/Makefile

@@ -49,7 +49,8 @@ endif
 
 ifndef CONFIG_CC_OPTIMIZE_FOR_SIZE
 # Generic build system uses -O2, we want -O3
-cflags-y  += -O3
+# Note: No need to add to cflags-y as that happens anyways
+ARCH_CFLAGS += -O3
 endif
 
 # small data is default for elf32 tool-chain. If not usable, disable it

arch/arc/boot/dts/axc003.dtsi

@@ -12,7 +12,7 @@
 
 / {
 	compatible = "snps,arc";
-	clock-frequency = <75000000>;
+	clock-frequency = <90000000>;
 	#address-cells = <1>;
 	#size-cells = <1>;
 

arch/arc/boot/dts/axc003_idu.dtsi

@@ -12,7 +12,7 @@
 
 / {
 	compatible = "snps,arc";
-	clock-frequency = <75000000>;
+	clock-frequency = <90000000>;
 	#address-cells = <1>;
 	#size-cells = <1>;
 

arch/arc/include/asm/Kbuild

@@ -22,6 +22,7 @@ generic-y += kvm_para.h
 generic-y += local.h
 generic-y += local64.h
 generic-y += mcs_spinlock.h
+generic-y += mm-arch-hooks.h
 generic-y += mman.h
 generic-y += msgbuf.h
 generic-y += param.h

arch/arc/include/asm/bitops.h

@@ -50,8 +50,7 @@ static inline void op##_bit(unsigned long nr, volatile unsigned long *m)\
 	 * done for const @nr, but no code is generated due to gcc	\
 	 * const prop.							\
 	 */								\
-	if (__builtin_constant_p(nr))					\
-		nr &= 0x1f;						\
+	nr &= 0x1f;							\
 									\
 	__asm__ __volatile__(						\
 	"1:	llock       %0, [%1]		\n"			\
@@ -82,8 +81,7 @@ static inline int test_and_##op##_bit(unsigned long nr, volatile unsigned long *
 									\
 	m += nr >> 5;							\
 									\
-	if (__builtin_constant_p(nr))					\
-		nr &= 0x1f;						\
+	nr &= 0x1f;							\
 									\
 	/*								\
 	 * Explicit full memory barrier needed before/after as		\
@@ -129,16 +127,13 @@ static inline void op##_bit(unsigned long nr, volatile unsigned long *m)\
 	unsigned long temp, flags;					\
 	m += nr >> 5;							\
 									\
-	if (__builtin_constant_p(nr))					\
-		nr &= 0x1f;						\
-									\
 	/*								\
 	 * spin lock/unlock provide the needed smp_mb() before/after	\
 	 */								\
 	bitops_lock(flags);						\
 									\
 	temp = *m;							\
-	*m = temp c_op (1UL << nr);					\
+	*m = temp c_op (1UL << (nr & 0x1f));					\
 									\
 	bitops_unlock(flags);						\
 }
@@ -149,17 +144,14 @@ static inline int test_and_##op##_bit(unsigned long nr, volatile unsigned long *
 	unsigned long old, flags;					\
 	m += nr >> 5;							\
 									\
-	if (__builtin_constant_p(nr))					\
-		nr &= 0x1f;						\
-									\
 	bitops_lock(flags);						\
 									\
 	old = *m;							\
-	*m = old c_op (1 << nr);					\
+	*m = old c_op (1UL << (nr & 0x1f));				\
 									\
 	bitops_unlock(flags);						\
 									\
-	return (old & (1 << nr)) != 0;					\
+	return (old & (1UL << (nr & 0x1f))) != 0;			\
 }
 
 #endif /* CONFIG_ARC_HAS_LLSC */
@@ -174,11 +166,8 @@ static inline void __##op##_bit(unsigned long nr, volatile unsigned long *m)	\
 	unsigned long temp;						\
 	m += nr >> 5;							\
 									\
-	if (__builtin_constant_p(nr))					\
-		nr &= 0x1f;						\
-									\
 	temp = *m;							\
-	*m = temp c_op (1UL << nr);					\
+	*m = temp c_op (1UL << (nr & 0x1f));				\
 }
 
 #define __TEST_N_BIT_OP(op, c_op, asm_op)				\
@@ -187,13 +176,10 @@ static inline int __test_and_##op##_bit(unsigned long nr, volatile unsigned long
 	unsigned long old;						\
 	m += nr >> 5;							\
 									\
-	if (__builtin_constant_p(nr))					\
-		nr &= 0x1f;						\
-									\
 	old = *m;							\
-	*m = old c_op (1 << nr);					\
+	*m = old c_op (1UL << (nr & 0x1f));				\
 									\
-	return (old & (1 << nr)) != 0;					\
+	return (old & (1UL << (nr & 0x1f))) != 0;			\
 }
 
 #define BIT_OPS(op, c_op, asm_op)					\
@@ -224,10 +210,7 @@ test_bit(unsigned int nr, const volatile unsigned long *addr)
 
 	addr += nr >> 5;
 
-	if (__builtin_constant_p(nr))
-		nr &= 0x1f;
-
-	mask = 1 << nr;
+	mask = 1UL << (nr & 0x1f);
 
 	return ((mask & *addr) != 0);
 }

arch/arc/include/asm/futex.h

@@ -16,12 +16,40 @@
 #include <linux/uaccess.h>
 #include <asm/errno.h>
 
+#ifdef CONFIG_ARC_HAS_LLSC
+
+#define __futex_atomic_op(insn, ret, oldval, uaddr, oparg)\
+							\
+	__asm__ __volatile__(				\
+	"1:	llock	%1, [%2]		\n"	\
+		insn				"\n"	\
+	"2:	scond	%0, [%2]		\n"	\
+	"	bnz	1b			\n"	\
+	"	mov %0, 0			\n"	\
+	"3:					\n"	\
+	"	.section .fixup,\"ax\"		\n"	\
+	"	.align  4			\n"	\
+	"4:	mov %0, %4			\n"	\
+	"	b   3b				\n"	\
+	"	.previous			\n"	\
+	"	.section __ex_table,\"a\"	\n"	\
+	"	.align  4			\n"	\
+	"	.word   1b, 4b			\n"	\
+	"	.word   2b, 4b			\n"	\
+	"	.previous			\n"	\
+							\
+	: "=&r" (ret), "=&r" (oldval)			\
+	: "r" (uaddr), "r" (oparg), "ir" (-EFAULT)	\
+	: "cc", "memory")
+
+#else	/* !CONFIG_ARC_HAS_LLSC */
+
 #define __futex_atomic_op(insn, ret, oldval, uaddr, oparg)\
 							\
 	__asm__ __volatile__(				\
-	"1:	ld  %1, [%2]			\n"	\
+	"1:	ld	%1, [%2]		\n"	\
 		insn				"\n"	\
-	"2:	st  %0, [%2]			\n"	\
+	"2:	st	%0, [%2]		\n"	\
 	"	mov %0, 0			\n"	\
 	"3:					\n"	\
 	"	.section .fixup,\"ax\"		\n"	\
@@ -39,6 +67,8 @@
 	: "r" (uaddr), "r" (oparg), "ir" (-EFAULT)	\
 	: "cc", "memory")
 
+#endif
+
 static inline int futex_atomic_op_inuser(int encoded_op, u32 __user *uaddr)
 {
 	int op = (encoded_op >> 28) & 7;
@@ -123,11 +153,17 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr, u32 oldval,
 
 	pagefault_disable();
 
-	/* TBD : can use llock/scond */
 	__asm__ __volatile__(
-	"1:	ld    %0, [%3]	\n"
-	"	brne  %0, %1, 3f	\n"
-	"2:	st    %2, [%3]	\n"
+#ifdef CONFIG_ARC_HAS_LLSC
+	"1:	llock	%0, [%3]		\n"
+	"	brne	%0, %1, 3f		\n"
+	"2:	scond	%2, [%3]		\n"
+	"	bnz	1b			\n"
+#else
+	"1:	ld	%0, [%3]		\n"
+	"	brne	%0, %1, 3f		\n"
+	"2:	st	%2, [%3]		\n"
+#endif
 	"3:	\n"
 	"	.section .fixup,\"ax\"	\n"
 	"4:	mov %0, %4	\n"

arch/arc/include/asm/mm-arch-hooks.h

@@ -1,15 +0,0 @@
-/*
- * Architecture specific mm hooks
- *
- * Copyright (C) 2015, IBM Corporation
- * Author: Laurent Dufour <ldufour@linux.vnet.ibm.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef _ASM_ARC_MM_ARCH_HOOKS_H
-#define _ASM_ARC_MM_ARCH_HOOKS_H
-
-#endif /* _ASM_ARC_MM_ARCH_HOOKS_H */

arch/arc/include/asm/ptrace.h

@@ -106,7 +106,7 @@ struct callee_regs {
 	long r25, r24, r23, r22, r21, r20, r19, r18, r17, r16, r15, r14, r13;
 };
 
-#define instruction_pointer(regs)	((regs)->ret)
+#define instruction_pointer(regs)	(unsigned long)((regs)->ret)
 #define profile_pc(regs)		instruction_pointer(regs)
 
 /* return 1 if user mode or 0 if kernel mode */

arch/arc/kernel/intc-arcv2.c

@@ -12,7 +12,6 @@
 #include <linux/of.h>
 #include <linux/irqdomain.h>
 #include <linux/irqchip.h>
-#include "../../drivers/irqchip/irqchip.h"
 #include <asm/irq.h>
 
 /*

arch/arc/kernel/intc-compact.c

@@ -12,7 +12,6 @@
 #include <linux/of.h>
 #include <linux/irqdomain.h>
 #include <linux/irqchip.h>
-#include "../../drivers/irqchip/irqchip.h"
 #include <asm/irq.h>
 
 /*

arch/arc/kernel/mcip.c

@@ -175,7 +175,6 @@ void mcip_init_early_smp(void)
 #include <linux/irqchip.h>
 #include <linux/of.h>
 #include <linux/of_irq.h>
-#include "../../drivers/irqchip/irqchip.h"
 
 /*
  * Set the DEST for @cmn_irq to @cpu_mask (1 bit per core)
@@ -218,11 +217,28 @@ static void idu_irq_unmask(struct irq_data *data)
 	raw_spin_unlock_irqrestore(&mcip_lock, flags);
 }
 
+#ifdef CONFIG_SMP
 static int
-idu_irq_set_affinity(struct irq_data *d, const struct cpumask *cpumask, bool f)
+idu_irq_set_affinity(struct irq_data *data, const struct cpumask *cpumask,
+		     bool force)
 {
+	unsigned long flags;
+	cpumask_t online;
+
+	/* errout if no online cpu per @cpumask */
+	if (!cpumask_and(&online, cpumask, cpu_online_mask))
+		return -EINVAL;
+
+	raw_spin_lock_irqsave(&mcip_lock, flags);
+
+	idu_set_dest(data->hwirq, cpumask_bits(&online)[0]);
+	idu_set_mode(data->hwirq, IDU_M_TRIG_LEVEL, IDU_M_DISTRI_RR);
+
+	raw_spin_unlock_irqrestore(&mcip_lock, flags);
+
 	return IRQ_SET_MASK_OK;
 }
+#endif
 
 static struct irq_chip idu_irq_chip = {
 	.name			= "MCIP IDU Intc",
@@ -330,8 +346,7 @@ idu_of_init(struct device_node *intc, struct device_node *parent)
 		if (!i)
 			idu_first_irq = irq;
 
-		irq_set_handler_data(irq, domain);
-		irq_set_chained_handler(irq, idu_cascade_isr);
+		irq_set_chained_handler_and_data(irq, idu_cascade_isr, domain);
 	}
 
 	__mcip_cmd(CMD_IDU_ENABLE, 0);

arch/arc/kernel/setup.c

@@ -142,17 +142,22 @@ static void read_arc_build_cfg_regs(void)
 }
 
 static const struct cpuinfo_data arc_cpu_tbl[] = {
+#ifdef CONFIG_ISA_ARCOMPACT
 	{ {0x20, "ARC 600"      }, 0x2F},
 	{ {0x30, "ARC 700"      }, 0x33},
 	{ {0x34, "ARC 700 R4.10"}, 0x34},
 	{ {0x35, "ARC 700 R4.11"}, 0x35},
-	{ {0x50, "ARC HS38"	}, 0x51},
+#else
+	{ {0x50, "ARC HS38 R2.0"}, 0x51},
+	{ {0x52, "ARC HS38 R2.1"}, 0x52},
+#endif
 	{ {0x00, NULL		} }
 };
 
-#define IS_AVAIL1(v, str)	((v) ? str : "")
-#define IS_USED(cfg)		(IS_ENABLED(cfg) ? "" : "(not used) ")
-#define IS_AVAIL2(v, str, cfg)  IS_AVAIL1(v, str), IS_AVAIL1(v, IS_USED(cfg))
+#define IS_AVAIL1(v, s)		((v) ? s : "")
+#define IS_USED_RUN(v)		((v) ? "" : "(not used) ")
+#define IS_USED_CFG(cfg)	IS_USED_RUN(IS_ENABLED(cfg))
+#define IS_AVAIL2(v, s, cfg)	IS_AVAIL1(v, s), IS_AVAIL1(v, IS_USED_CFG(cfg))
 
 static char *arc_cpu_mumbojumbo(int cpu_id, char *buf, int len)
 {
@@ -226,7 +231,7 @@ static char *arc_cpu_mumbojumbo(int cpu_id, char *buf, int len)
 			n += scnprintf(buf + n, len - n, "mpy[opt %d] ", opt);
 		}
 		n += scnprintf(buf + n, len - n, "%s",
-			       IS_USED(CONFIG_ARC_HAS_HW_MPY));
+			       IS_USED_CFG(CONFIG_ARC_HAS_HW_MPY));
 	}
 
 	n += scnprintf(buf + n, len - n, "%s%s%s%s%s%s%s%s\n",

arch/arc/kernel/troubleshoot.c

@@ -58,7 +58,6 @@ static void show_callee_regs(struct callee_regs *cregs)
 
 static void print_task_path_n_nm(struct task_struct *tsk, char *buf)
 {
-	struct path path;
 	char *path_nm = NULL;
 	struct mm_struct *mm;
 	struct file *exe_file;

arch/arc/mm/cache.c

@@ -468,10 +468,18 @@ static void __ic_line_inv_vaddr(unsigned long paddr, unsigned long vaddr,
 noinline void slc_op(unsigned long paddr, unsigned long sz, const int op)
 {
 #ifdef CONFIG_ISA_ARCV2
+	/*
+	 * SLC is shared between all cores and concurrent aux operations from
+	 * multiple cores need to be serialized using a spinlock
+	 * A concurrent operation can be silently ignored and/or the old/new
+	 * operation can remain incomplete forever (lockup in SLC_CTRL_BUSY loop
+	 * below)
+	 */
+	static DEFINE_SPINLOCK(lock);
 	unsigned long flags;
 	unsigned int ctrl;
 
-	local_irq_save(flags);
+	spin_lock_irqsave(&lock, flags);
 
 	/*
 	 * The Region Flush operation is specified by CTRL.RGN_OP[11..9]
@@ -504,7 +512,7 @@ noinline void slc_op(unsigned long paddr, unsigned long sz, const int op)
 
 	while (read_aux_reg(ARC_REG_SLC_CTRL) & SLC_CTRL_BUSY);
 
-	local_irq_restore(flags);
+	spin_unlock_irqrestore(&lock, flags);
 #endif
 }
 

arch/arc/mm/dma.c

@@ -60,8 +60,8 @@ void *dma_alloc_coherent(struct device *dev, size_t size,
 
 	/* This is kernel Virtual address (0x7000_0000 based) */
 	kvaddr = ioremap_nocache((unsigned long)paddr, size);
-	if (kvaddr != NULL)
-		memset(kvaddr, 0, size);
+	if (kvaddr == NULL)
+		return NULL;
 
 	/* This is bus address, platform dependent */
 	*dma_handle = (dma_addr_t)paddr;

arch/arm/boot/dts/am335x-pepper.dts

@@ -74,6 +74,7 @@
 	audio_codec: tlv320aic3106@1b {
 		compatible = "ti,tlv320aic3106";
 		reg = <0x1b>;
+		ai3x-micbias-vg = <0x2>;
 	};
 
 	accel: lis331dlh@1d {
@@ -153,7 +154,7 @@
 	ti,audio-routing =
 		"Headphone Jack",	"HPLOUT",
 		"Headphone Jack",	"HPROUT",
-		"LINE1L",		"Line In";
+		"MIC3L",		"Mic3L Switch";
 };
 
 &mcasp0 {
@@ -438,41 +439,50 @@
 	regulators {
 		dcdc1_reg: regulator@0 {
 			/* VDD_1V8 system supply */
+			regulator-always-on;
 		};
 
 		dcdc2_reg: regulator@1 {
 			/* VDD_CORE voltage limits 0.95V - 1.26V with +/-4% tolerance */
 			regulator-name = "vdd_core";
 			regulator-min-microvolt = <925000>;
-			regulator-max-microvolt = <1325000>;
+			regulator-max-microvolt = <1150000>;
 			regulator-boot-on;
+			regulator-always-on;
 		};
 
 		dcdc3_reg: regulator@2 {
 			/* VDD_MPU voltage limits 0.95V - 1.1V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <925000>;
-			regulator-max-microvolt = <1150000>;
+			regulator-max-microvolt = <1325000>;
 			regulator-boot-on;
+			regulator-always-on;
 		};
 
 		ldo1_reg: regulator@3 {
 			/* VRTC 1.8V always-on supply */
+			regulator-name = "vrtc,vdds";
 			regulator-always-on;
 		};
 
 		ldo2_reg: regulator@4 {
 			/* 3.3V rail */
+			regulator-name = "vdd_3v3aux";
+			regulator-always-on;
 		};
 
 		ldo3_reg: regulator@5 {
 			/* VDD_3V3A 3.3V rail */
+			regulator-name = "vdd_3v3a";
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;
 		};
 
 		ldo4_reg: regulator@6 {
 			/* VDD_3V3B 3.3V rail */
+			regulator-name = "vdd_3v3b";
+			regulator-always-on;
 		};
 	};
 };

arch/arm/boot/dts/cros-ec-keyboard.dtsi

@@ -22,6 +22,7 @@
 			MATRIX_KEY(0x00, 0x02, KEY_F1)
 			MATRIX_KEY(0x00, 0x03, KEY_B)
 			MATRIX_KEY(0x00, 0x04, KEY_F10)
+			MATRIX_KEY(0x00, 0x05, KEY_RO)
 			MATRIX_KEY(0x00, 0x06, KEY_N)
 			MATRIX_KEY(0x00, 0x08, KEY_EQUAL)
 			MATRIX_KEY(0x00, 0x0a, KEY_RIGHTALT)
@@ -34,6 +35,7 @@
 			MATRIX_KEY(0x01, 0x08, KEY_APOSTROPHE)
 			MATRIX_KEY(0x01, 0x09, KEY_F9)
 			MATRIX_KEY(0x01, 0x0b, KEY_BACKSPACE)
+			MATRIX_KEY(0x01, 0x0c, KEY_HENKAN)
 
 			MATRIX_KEY(0x02, 0x00, KEY_LEFTCTRL)
 			MATRIX_KEY(0x02, 0x01, KEY_TAB)
@@ -45,6 +47,7 @@
 			MATRIX_KEY(0x02, 0x07, KEY_102ND)
 			MATRIX_KEY(0x02, 0x08, KEY_LEFTBRACE)
 			MATRIX_KEY(0x02, 0x09, KEY_F8)
+			MATRIX_KEY(0x02, 0x0a, KEY_YEN)
 
 			MATRIX_KEY(0x03, 0x01, KEY_GRAVE)
 			MATRIX_KEY(0x03, 0x02, KEY_F2)
@@ -53,6 +56,7 @@
 			MATRIX_KEY(0x03, 0x06, KEY_6)
 			MATRIX_KEY(0x03, 0x08, KEY_MINUS)
 			MATRIX_KEY(0x03, 0x0b, KEY_BACKSLASH)
+			MATRIX_KEY(0x03, 0x0c, KEY_MUHENKAN)
 
 			MATRIX_KEY(0x04, 0x00, KEY_RIGHTCTRL)
 			MATRIX_KEY(0x04, 0x01, KEY_A)

arch/arm/boot/dts/dra7-evm.dts

@@ -686,7 +686,8 @@
 
 &dcan1 {
 	status = "ok";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&dcan1_pins_default>;
+	pinctrl-names = "default", "sleep", "active";
+	pinctrl-0 = <&dcan1_pins_sleep>;
 	pinctrl-1 = <&dcan1_pins_sleep>;
+	pinctrl-2 = <&dcan1_pins_default>;
 };

arch/arm/boot/dts/dra72-evm.dts

@@ -587,9 +587,10 @@
 
 &dcan1 {
 	status = "ok";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&dcan1_pins_default>;
+	pinctrl-names = "default", "sleep", "active";
+	pinctrl-0 = <&dcan1_pins_sleep>;
 	pinctrl-1 = <&dcan1_pins_sleep>;
+	pinctrl-2 = <&dcan1_pins_default>;
 };
 
 &qspi {

arch/arm/boot/dts/imx23.dtsi

@@ -468,6 +468,7 @@
 				interrupts = <36 37 38 39 40 41 42 43 44>;
 				status = "disabled";
 				clocks = <&clks 26>;
+				#io-channel-cells = <1>;
 			};
 
 			spdif@80054000 {

arch/arm/boot/dts/imx25-pdk.dts

@@ -10,6 +10,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include "imx25.dtsi"
 
@@ -114,8 +115,8 @@
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio2 1 0>;
-	wp-gpios = <&gpio2 0 0>;
+	cd-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx27.dtsi

@@ -108,7 +108,7 @@
 			};
 
 			gpt1: timer@10003000 {
-				compatible = "fsl,imx27-gpt", "fsl,imx1-gpt";
+				compatible = "fsl,imx27-gpt", "fsl,imx21-gpt";
 				reg = <0x10003000 0x1000>;
 				interrupts = <26>;
 				clocks = <&clks IMX27_CLK_GPT1_IPG_GATE>,
@@ -117,7 +117,7 @@
 			};
 
 			gpt2: timer@10004000 {
-				compatible = "fsl,imx27-gpt", "fsl,imx1-gpt";
+				compatible = "fsl,imx27-gpt", "fsl,imx21-gpt";
 				reg = <0x10004000 0x1000>;
 				interrupts = <25>;
 				clocks = <&clks IMX27_CLK_GPT2_IPG_GATE>,
@@ -126,7 +126,7 @@
 			};
 
 			gpt3: timer@10005000 {
-				compatible = "fsl,imx27-gpt", "fsl,imx1-gpt";
+				compatible = "fsl,imx27-gpt", "fsl,imx21-gpt";
 				reg = <0x10005000 0x1000>;
 				interrupts = <24>;
 				clocks = <&clks IMX27_CLK_GPT3_IPG_GATE>,
@@ -376,7 +376,7 @@
 			};
 
 			gpt4: timer@10019000 {
-				compatible = "fsl,imx27-gpt", "fsl,imx1-gpt";
+				compatible = "fsl,imx27-gpt", "fsl,imx21-gpt";
 				reg = <0x10019000 0x1000>;
 				interrupts = <4>;
 				clocks = <&clks IMX27_CLK_GPT4_IPG_GATE>,
@@ -385,7 +385,7 @@
 			};
 
 			gpt5: timer@1001a000 {
-				compatible = "fsl,imx27-gpt", "fsl,imx1-gpt";
+				compatible = "fsl,imx27-gpt", "fsl,imx21-gpt";
 				reg = <0x1001a000 0x1000>;
 				interrupts = <3>;
 				clocks = <&clks IMX27_CLK_GPT5_IPG_GATE>,
@@ -436,7 +436,7 @@
 			};
 
 			gpt6: timer@1001f000 {
-				compatible = "fsl,imx27-gpt", "fsl,imx1-gpt";
+				compatible = "fsl,imx27-gpt", "fsl,imx21-gpt";
 				reg = <0x1001f000 0x1000>;
 				interrupts = <2>;
 				clocks = <&clks IMX27_CLK_GPT6_IPG_GATE>,

arch/arm/boot/dts/imx51-apf51dev.dts

@@ -98,7 +98,7 @@
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
 	status = "okay";
 };

arch/arm/boot/dts/imx53-ard.dts

@@ -103,8 +103,8 @@
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio1 1 0>;
-	wp-gpios = <&gpio1 9 0>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx53-m53evk.dts

@@ -124,8 +124,8 @@
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio1 1 0>;
-	wp-gpios = <&gpio1 9 0>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx53-qsb-common.dtsi

@@ -147,8 +147,8 @@
 &esdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc3>;
-	cd-gpios = <&gpio3 11 0>;
-	wp-gpios = <&gpio3 12 0>;
+	cd-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 12 GPIO_ACTIVE_HIGH>;
 	bus-width = <8>;
 	status = "okay";
 };
@@ -295,9 +295,10 @@
 &tve {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_vga_sync>;
+	ddc-i2c-bus = <&i2c2>;
 	fsl,tve-mode = "vga";
-	fsl,hsync-pin = <4>;
-	fsl,vsync-pin = <6>;
+	fsl,hsync-pin = <7>;	/* IPU DI1 PIN7 via EIM_OE */
+	fsl,vsync-pin = <8>;	/* IPU DI1 PIN8 via EIM_RW */
 	status = "okay";
 };
 

arch/arm/boot/dts/imx53-smd.dts

@@ -41,8 +41,8 @@
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio3 13 0>;
-	wp-gpios = <&gpio4 11 0>;
+	cd-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx53-tqma53.dtsi

@@ -41,8 +41,8 @@
 	pinctrl-0 = <&pinctrl_esdhc2>,
 		    <&pinctrl_esdhc2_cdwp>;
 	vmmc-supply = <&reg_3p3v>;
-	wp-gpios = <&gpio1 2 0>;
-	cd-gpios = <&gpio1 4 0>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 	status = "disabled";
 };
 

arch/arm/boot/dts/imx53-tx53.dtsi

@@ -183,7 +183,7 @@
 };
 
 &esdhc1 {
-	cd-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
 	fsl,wp-controller;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
@@ -191,7 +191,7 @@
 };
 
 &esdhc2 {
-	cd-gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
 	fsl,wp-controller;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc2>;

arch/arm/boot/dts/imx53-voipac-bsb.dts

@@ -119,8 +119,8 @@
 &esdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc2>;
-	cd-gpios = <&gpio3 25 0>;
-	wp-gpios = <&gpio2 19 0>;
+	cd-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6dl-riotboard.dts

@@ -305,8 +305,8 @@
 &usdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
-	cd-gpios = <&gpio1 4 0>;
-	wp-gpios = <&gpio1 2 0>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };
@@ -314,8 +314,8 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 0>;
-	wp-gpios = <&gpio7 1 0>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6q-arm2.dts

@@ -11,6 +11,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "imx6q.dtsi"
 
 / {
@@ -196,8 +197,8 @@
 };
 
 &usdhc3 {
-	cd-gpios = <&gpio6 11 0>;
-	wp-gpios = <&gpio6 14 0>;
+	cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&reg_3p3v>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3

arch/arm/boot/dts/imx6q-gk802.dts

@@ -7,6 +7,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "imx6q.dtsi"
 
 / {
@@ -161,7 +162,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <4>;
-	cd-gpios = <&gpio6 11 0>;
+	cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6q-tbs2910.dts

@@ -251,7 +251,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <4>;
-	cd-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };
@@ -260,7 +260,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <4>;
-	cd-gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";

arch/arm/boot/dts/imx6qdl-aristainetos.dtsi

@@ -173,7 +173,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
 	vmmc-supply = <&reg_3p3v>;
-	cd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
@@ -181,7 +181,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	vmmc-supply = <&reg_3p3v>;
-	cd-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio4 8 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi

@@ -392,7 +392,7 @@
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
-	cd-gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
 	no-1-8-v;
 	status = "okay";
 };
@@ -400,7 +400,7 @@
 &usdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
-	cd-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
 	no-1-8-v;
 	status = "okay";

arch/arm/boot/dts/imx6qdl-cubox-i.dtsi

@@ -258,6 +258,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_cubox_i_usdhc2_aux &pinctrl_cubox_i_usdhc2>;
 	vmmc-supply = <&reg_3p3v>;
-	cd-gpios = <&gpio1 4 0>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi

@@ -1,3 +1,5 @@
+#include <dt-bindings/gpio/gpio.h>
+
 / {
 	regulators {
 		compatible = "simple-bus";
@@ -181,7 +183,7 @@
 &usdhc2 { /* module slot */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
-	cd-gpios = <&gpio2 2 0>;
+	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx6qdl-gw52xx.dtsi

@@ -318,7 +318,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-gw53xx.dtsi

@@ -324,7 +324,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-gw54xx.dtsi

@@ -417,7 +417,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-hummingboard.dtsi

@@ -299,6 +299,6 @@
 		&pinctrl_hummingboard_usdhc2
 	>;
 	vmmc-supply = <&reg_3p3v>;
-	cd-gpios = <&gpio1 4 0>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi

@@ -453,7 +453,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 0>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };
@@ -461,7 +461,7 @@
 &usdhc4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc4>;
-	cd-gpios = <&gpio2 6 0>;
+	cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi

@@ -409,8 +409,8 @@
 &usdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
-	cd-gpios = <&gpio1 4 0>;
-	wp-gpios = <&gpio1 2 0>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 	status = "disabled";
 };
 
@@ -418,7 +418,7 @@
         pinctrl-names = "default";
         pinctrl-0 = <&pinctrl_usdhc3
 		     &pinctrl_usdhc3_cdwp>;
-        cd-gpios = <&gpio1 27 0>;
-        wp-gpios = <&gpio1 29 0>;
+	cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
         status = "disabled";
 };

arch/arm/boot/dts/imx6qdl-rex.dtsi

@@ -342,7 +342,7 @@
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
@@ -351,6 +351,6 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-sabreauto.dtsi

@@ -467,8 +467,8 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
-	cd-gpios = <&gpio6 15 0>;
-	wp-gpios = <&gpio1 13 0>;
+	cd-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx6qdl-sabrelite.dtsi

@@ -448,8 +448,8 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 0>;
-	wp-gpios = <&gpio7 1 0>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };
@@ -457,7 +457,7 @@
 &usdhc4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc4>;
-	cd-gpios = <&gpio2 6 0>;
+	cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-sabresd.dtsi

@@ -562,8 +562,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <8>;
-	cd-gpios = <&gpio2 2 0>;
-	wp-gpios = <&gpio2 3 0>;
+	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
@@ -571,8 +571,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <8>;
-	cd-gpios = <&gpio2 0 0>;
-	wp-gpios = <&gpio2 1 0>;
+	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx6qdl-tx6.dtsi

@@ -680,7 +680,7 @@
 	pinctrl-0 = <&pinctrl_usdhc1>;
 	bus-width = <4>;
 	no-1-8-v;
-	cd-gpios = <&gpio7 2 0>;
+	cd-gpios = <&gpio7 2 GPIO_ACTIVE_LOW>;
 	fsl,wp-controller;
 	status = "okay";
 };
@@ -690,7 +690,7 @@
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <4>;
 	no-1-8-v;
-	cd-gpios = <&gpio7 3 0>;
+	cd-gpios = <&gpio7 3 GPIO_ACTIVE_LOW>;
 	fsl,wp-controller;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-wandboard.dtsi

@@ -9,6 +9,8 @@
  *
  */
 
+#include <dt-bindings/gpio/gpio.h>
+
 / {
 	regulators {
 		compatible = "simple-bus";
@@ -250,13 +252,13 @@
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
-	cd-gpios = <&gpio1 2 0>;
+	cd-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio3 9 0>;
+	cd-gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6sl-evk.dts

@@ -617,8 +617,8 @@
 	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
 	bus-width = <8>;
-	cd-gpios = <&gpio4 7 0>;
-	wp-gpios = <&gpio4 6 0>;
+	cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
@@ -627,8 +627,8 @@
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
-	cd-gpios = <&gpio5 0 0>;
-	wp-gpios = <&gpio4 29 0>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
@@ -637,6 +637,6 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
-	cd-gpios = <&gpio3 22 0>;
+	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6sx-sabreauto.dts

@@ -49,7 +49,7 @@
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	bus-width = <8>;
-	cd-gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio7 10 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
 	keep-power-in-suspend;
 	enable-sdio-wakeup;
@@ -61,7 +61,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc4>;
 	bus-width = <8>;
-	cd-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio7 11 GPIO_ACTIVE_LOW>;
 	no-1-8-v;
 	keep-power-in-suspend;
 	enable-sdio-wakup;

arch/arm/boot/dts/imx6sx-sdb.dtsi

@@ -293,7 +293,7 @@
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	bus-width = <8>;
-	cd-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
 	keep-power-in-suspend;
 	enable-sdio-wakeup;
@@ -304,7 +304,7 @@
 &usdhc4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc4>;
-	cd-gpios = <&gpio6 21 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio6 21 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };

arch/arm/boot/dts/imx7d-sdb.dts

@@ -234,8 +234,8 @@
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
-	cd-gpios = <&gpio5 0 0>;
-	wp-gpios = <&gpio5 1 0>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
 	enable-sdio-wakeup;
 	keep-power-in-suspend;
 	status = "okay";

arch/arm/boot/dts/k2e.dtsi

@@ -86,7 +86,7 @@
 			gpio,syscon-dev = <&devctrl 0x240>;
 		};
 
-		pcie@21020000 {
+		pcie1: pcie@21020000 {
 			compatible = "ti,keystone-pcie","snps,dw-pcie";
 			clocks = <&clkpcie1>;
 			clock-names = "pcie";
@@ -96,6 +96,7 @@
 			ranges = <0x81000000 0 0 0x23260000 0x4000 0x4000
 				0x82000000 0 0x60000000 0x60000000 0 0x10000000>;
 
+			status = "disabled";
 			device_type = "pci";
 			num-lanes = <2>;
 

arch/arm/boot/dts/keystone.dtsi

@@ -286,7 +286,7 @@
 			ti,syscon-dev = <&devctrl 0x2a0>;
 		};
 
-		pcie@21800000 {
+		pcie0: pcie@21800000 {
 			compatible = "ti,keystone-pcie", "snps,dw-pcie";
 			clocks = <&clkpcie>;
 			clock-names = "pcie";
@@ -296,6 +296,7 @@
 			ranges = <0x81000000 0 0 0x23250000 0 0x4000
 				0x82000000 0 0x50000000 0x50000000 0 0x10000000>;
 
+			status = "disabled";
 			device_type = "pci";
 			num-lanes = <2>;
 

arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi

@@ -120,7 +120,7 @@
 
 	lcd0: display@0 {
 		compatible = "lgphilips,lb035q02";
-		label = "lcd";
+		label = "lcd35";
 
 		reg = <1>;					/* CS1 */
 		spi-max-frequency = <10000000>;

arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi

@@ -98,7 +98,7 @@
 
 	lcd0: display@0 {
 		compatible = "samsung,lte430wq-f0c", "panel-dpi";
-		label = "lcd";
+		label = "lcd43";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&lte430_pins>;

arch/arm/boot/dts/omap4.dtsi

@@ -551,6 +551,7 @@
 			reg = <0x4a066000 0x100>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmu_dsp";
+			#iommu-cells = <0>;
 		};
 
 		mmu_ipu: mmu@55082000 {
@@ -558,6 +559,7 @@
 			reg = <0x55082000 0x100>;
 			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmu_ipu";
+			#iommu-cells = <0>;
 			ti,iommu-bus-err-back;
 		};
 

arch/arm/boot/dts/omap5.dtsi

@@ -612,6 +612,7 @@
 			reg = <0x4a066000 0x100>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmu_dsp";
+			#iommu-cells = <0>;
 		};
 
 		mmu_ipu: mmu@55082000 {
@@ -619,6 +620,7 @@
 			reg = <0x55082000 0x100>;
 			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmu_ipu";
+			#iommu-cells = <0>;
 			ti,iommu-bus-err-back;
 		};
 

arch/arm/boot/dts/socfpga_cyclone5_sockit.dts

@@ -60,27 +60,27 @@
 	rxc-skew-ps = <2000>;
 };
 
-&mmc0 {
-	vmmc-supply = <&regulator_3_3v>;
-	vqmmc-supply = <&regulator_3_3v>;
-};
-
-&usb1 {
-	status = "okay";
-};
-
 &gpio2 {
 	status = "okay";
 };
 
-&i2c1{
+&i2c1 {
 	status = "okay";
 
-	accel1: accel1@53{
-		compatible = "adxl34x";
+	accel1: accelerometer@53 {
+		compatible = "adi,adxl345";
 		reg = <0x53>;
 
-		interrupt-parent = < &portc >;
+		interrupt-parent = <&portc>;
 		interrupts = <3 2>;
 	};
 };
+
+&mmc0 {
+	vmmc-supply = <&regulator_3_3v>;
+	vqmmc-supply = <&regulator_3_3v>;
+};
+
+&usb1 {
+	status = "okay";
+};

arch/arm/boot/dts/spear1310-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr1310 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear1310.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for all SPEAr1310 SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear1340-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr1340 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear1340.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for all SPEAr1340 SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear13xx.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for all SPEAr13xx SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear300-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr300 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear300.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr300 SoC
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear310-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr310 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear310.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr310 SoC
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear320-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr320 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear320.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr320 SoC
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear3xx.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for all SPEAr3xx SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/ste-ccu8540.dts

@@ -17,6 +17,13 @@
 	model = "ST-Ericsson U8540 platform with Device Tree";
 	compatible = "st-ericsson,ccu8540", "st-ericsson,u8540";
 
+	/* This stablilizes the serial port enumeration */
+	aliases {
+		serial0 = &ux500_serial0;
+		serial1 = &ux500_serial1;
+		serial2 = &ux500_serial2;
+	};
+
 	memory@0 {
 		device_type = "memory";
 		reg = <0x20000000 0x1f000000>, <0xc0000000 0x3f000000>;

arch/arm/boot/dts/ste-ccu9540.dts

@@ -16,6 +16,13 @@
 	model = "ST-Ericsson CCU9540 platform with Device Tree";
 	compatible = "st-ericsson,ccu9540", "st-ericsson,u9540";
 
+	/* This stablilizes the serial port enumeration */
+	aliases {
+		serial0 = &ux500_serial0;
+		serial1 = &ux500_serial1;
+		serial2 = &ux500_serial2;
+	};
+
 	memory {
 		reg = <0x00000000 0x20000000>;
 	};

arch/arm/boot/dts/ste-dbx5x0.dtsi

@@ -971,7 +971,7 @@
 			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
-		uart@80120000 {
+		ux500_serial0: uart@80120000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x80120000 0x1000>;
 			interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
@@ -986,7 +986,7 @@
 			status = "disabled";
 		};
 
-		uart@80121000 {
+		ux500_serial1: uart@80121000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x80121000 0x1000>;
 			interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>;
@@ -1001,7 +1001,7 @@
 			status = "disabled";
 		};
 
-		uart@80007000 {
+		ux500_serial2: uart@80007000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x80007000 0x1000>;
 			interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/boot/dts/ste-href.dtsi

@@ -32,11 +32,11 @@
 			status = "okay";
 		};
 
+		/* This UART is unused and thus left disabled */
 		uart@80121000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart1_default_mode>;
 			pinctrl-1 = <&uart1_sleep_mode>;
-			status = "okay";
 		};
 
 		uart@80007000 {

arch/arm/boot/dts/ste-hrefprev60-stuib.dts

@@ -17,6 +17,13 @@
 	model = "ST-Ericsson HREF (pre-v60) and ST UIB";
 	compatible = "st-ericsson,mop500", "st-ericsson,u8500";
 
+	/* This stablilizes the serial port enumeration */
+	aliases {
+		serial0 = &ux500_serial0;
+		serial1 = &ux500_serial1;
+		serial2 = &ux500_serial2;
+	};
+
 	soc {
 		/* Reset line for the BU21013 touchscreen */
 		i2c@80110000 {

arch/arm/boot/dts/ste-hrefprev60-tvk.dts

@@ -16,4 +16,11 @@
 / {
 	model = "ST-Ericsson HREF (pre-v60) and TVK1281618 UIB";
 	compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+	/* This stablilizes the serial port enumeration */
+	aliases {
+		serial0 = &ux500_serial0;
+		serial1 = &ux500_serial1;
+		serial2 = &ux500_serial2;
+	};
 };

arch/arm/boot/dts/ste-hrefprev60.dtsi

@@ -23,6 +23,11 @@
 	};
 
 	soc {
+		/* Enable UART1 on this board */
+		uart@80121000 {
+			status = "okay";
+		};
+
 		i2c@80004000 {
 			tps61052@33 {
 				compatible = "tps61052";

arch/arm/boot/dts/ste-hrefv60plus-stuib.dts

@@ -19,6 +19,13 @@
 	model = "ST-Ericsson HREF (v60+) and ST UIB";
 	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
 
+	/* This stablilizes the serial port enumeration */
+	aliases {
+		serial0 = &ux500_serial0;
+		serial1 = &ux500_serial1;
+		serial2 = &ux500_serial2;
+	};
+
 	soc {
 		/* Reset line for the BU21013 touchscreen */
 		i2c@80110000 {

arch/arm/boot/dts/ste-hrefv60plus-tvk.dts

@@ -18,4 +18,11 @@
 / {
 	model = "ST-Ericsson HREF (v60+) and TVK1281618 UIB";
 	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+	/* This stablilizes the serial port enumeration */
+	aliases {
+		serial0 = &ux500_serial0;
+		serial1 = &ux500_serial1;
+		serial2 = &ux500_serial2;
+	};
 };

arch/arm/boot/dts/ste-hrefv60plus.dtsi

@@ -43,15 +43,26 @@
 				  <&vaudio_hf_hrefv60_mode>,
 				  <&gbf_hrefv60_mode>,
 				  <&hdtv_hrefv60_mode>,
-				  <&touch_hrefv60_mode>;
+				  <&touch_hrefv60_mode>,
+				  <&gpios_hrefv60_mode>;
 
 			sdi0 {
-				/* SD card detect GPIO pin, extend default state */
 				sdi0_default_mode: sdi0_default {
+					/* SD card detect GPIO pin, extend default state */
 					default_hrefv60_cfg1 {
 						pins = "GPIO95_E8";
 						ste,config = <&gpio_in_pu>;
 					};
+					/* VMMCI level-shifter enable */
+					default_hrefv60_cfg2 {
+						pins = "GPIO169_D22";
+						ste,config = <&gpio_out_lo>;
+					};
+					/* VMMCI level-shifter voltage select */
+					default_hrefv60_cfg3 {
+						pins = "GPIO5_AG6";
+						ste,config = <&gpio_out_hi>;
+					};
 				};
 			};
 			ipgpio {
@@ -213,6 +224,16 @@
 					};
 				};
 			};
+			gpios {
+				/* Dangling GPIO pins */
+				gpios_hrefv60_mode: gpios_hrefv60 {
+					default_cfg1 {
+						/* Normally UART1 RXD, now dangling */
+						pins = "GPIO4_AH6";
+						ste,config = <&in_pu>;
+					};
+				};
+			};
 		};
 	};
 };

arch/arm/boot/dts/ste-snowball.dts

@@ -18,6 +18,13 @@
 	model = "Calao Systems Snowball platform with device tree";
 	compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";
 
+	/* This stablilizes the serial port enumeration */
+	aliases {
+		serial0 = &ux500_serial0;
+		serial1 = &ux500_serial1;
+		serial2 = &ux500_serial2;
+	};
+
 	memory {
 		reg = <0x00000000 0x20000000>;
 	};
@@ -223,11 +230,11 @@
 			status = "okay";
 		};
 
+		/* This UART is unused and thus left disabled */
 		uart@80121000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart1_default_mode>;
 			pinctrl-1 = <&uart1_sleep_mode>;
-			status = "okay";
 		};
 
 		uart@80007000 {
@@ -452,7 +459,21 @@
 						pins = "GPIO21_AB3"; /* DAT31DIR */
 						ste,config = <&out_hi>;
 					};
-
+					/* SD card detect GPIO pin, extend default state */
+					snowball_cfg2 {
+						pins = "GPIO218_AH11";
+						ste,config = <&gpio_in_pu>;
+					};
+					/* VMMCI level-shifter enable */
+					snowball_cfg3 {
+						pins = "GPIO217_AH12";
+						ste,config = <&gpio_out_lo>;
+					};
+					/* VMMCI level-shifter voltage select */
+					snowball_cfg4 {
+						pins = "GPIO228_AJ6";
+						ste,config = <&gpio_out_hi>;
+					};
 				};
 			};
 			ssp0 {