ARM: at91: Remove the support for the RSI EWS board

The platform is end of life/support and should not clutter
the mach-at91 directory with non-DT files. It is therefore
removed.

Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

arch/arm/mach-at91/Kconfig.non_dt

@@ -132,12 +132,6 @@ config MACH_ECO920
 	bool "eco920"
 	help
 	  Select this if you are using the eco920 board
-
-config MACH_RSI_EWS
-	bool "RSI Embedded Webserver"
-	depends on ARCH_AT91RM9200
-	help
-	  Select this if you are using RSIs EWS board.
 endif
 
 # ----------------------------------------------------------

arch/arm/mach-at91/Makefile

@@ -46,7 +46,6 @@ obj-$(CONFIG_MACH_ECBAT91)	+= board-ecbat91.o
 obj-$(CONFIG_MACH_YL9200)	+= board-yl-9200.o
 obj-$(CONFIG_MACH_CPUAT91)	+= board-cpuat91.o
 obj-$(CONFIG_MACH_ECO920)	+= board-eco920.o
-obj-$(CONFIG_MACH_RSI_EWS)	+= board-rsi-ews.o
 
 # AT91SAM9260 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o

arch/arm/mach-at91/board-rsi-ews.c

@@ -1,232 +0,0 @@
-/*
- * board-rsi-ews.c
- *
- *  Copyright (C)
- *  2005 SAN People,
- *  2008-2011 R-S-I Elektrotechnik GmbH & Co. KG
- *
- * Licensed under GPLv2 or later.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-
-#include <linux/gpio.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-static void __init rsi_ews_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * Ethernet
- */
-static struct macb_platform_data rsi_ews_eth_data __initdata = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 1,
-};
-
-/*
- * USB Host
- */
-static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * SD/MC
- */
-static struct mci_platform_data __initdata rsi_ews_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PB27,
-		.wp_pin		= AT91_PIN_PB29,
-	},
-};
-
-/*
- * I2C
- */
-static struct i2c_board_info rsi_ews_i2c_devices[] __initdata = {
-	{
-		I2C_BOARD_INFO("ds1337", 0x68),
-	},
-	{
-		I2C_BOARD_INFO("24c01", 0x50),
-	}
-};
-
-/*
- * LEDs
- */
-static struct gpio_led rsi_ews_leds[] = {
-	{
-		.name			= "led0",
-		.gpio			= AT91_PIN_PB6,
-		.active_low		= 0,
-	},
-	{
-		.name			= "led1",
-		.gpio			= AT91_PIN_PB7,
-		.active_low		= 0,
-	},
-	{
-		.name			= "led2",
-		.gpio			= AT91_PIN_PB8,
-		.active_low		= 0,
-	},
-	{
-		.name			= "led3",
-		.gpio			= AT91_PIN_PB9,
-		.active_low		= 0,
-	},
-};
-
-/*
- * DataFlash
- */
-static struct spi_board_info rsi_ews_spi_devices[] = {
-	{	/* DataFlash chip 1*/
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 5 * 1000 * 1000,
-	},
-	{	/* DataFlash chip 2*/
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 5 * 1000 * 1000,
-	},
-};
-
-/*
- * NOR flash
- */
-static struct mtd_partition rsiews_nor_partitions[] = {
-	{
-		.name		= "boot",
-		.offset		= 0,
-		.size		= 3 * SZ_128K,
-		.mask_flags	= MTD_WRITEABLE
-	},
-	{
-		.name		= "kernel",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= SZ_2M - (3 * SZ_128K)
-	},
-	{
-		.name		= "root",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= SZ_8M
-	},
-	{
-		.name		= "kernelupd",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= 3 * SZ_512K,
-		.mask_flags	= MTD_WRITEABLE
-	},
-	{
-		.name		= "rootupd",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= 9 * SZ_512K,
-		.mask_flags	= MTD_WRITEABLE
-	},
-};
-
-static struct physmap_flash_data rsiews_nor_data = {
-	.width		= 2,
-	.parts		= rsiews_nor_partitions,
-	.nr_parts	= ARRAY_SIZE(rsiews_nor_partitions),
-};
-
-#define NOR_BASE	AT91_CHIPSELECT_0
-#define NOR_SIZE	SZ_16M
-
-static struct resource nor_flash_resources[] = {
-	{
-		.start	= NOR_BASE,
-		.end	= NOR_BASE + NOR_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device rsiews_nor_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-				.platform_data	= &rsiews_nor_data,
-	},
-	.resource	= nor_flash_resources,
-	.num_resources	= ARRAY_SIZE(nor_flash_resources),
-};
-
-/*
- * Init Func
- */
-static void __init rsi_ews_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	/* This one is for debugging */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	/* Dialin/-out modem interface */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART3 on ttyS4. (Rx, Tx, RTS) */
-	/* RS485 communication */
-	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
-	at91_add_device_serial();
-	at91_set_gpio_output(AT91_PIN_PA21, 0);
-	/* Ethernet */
-	at91_add_device_eth(&rsi_ews_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&rsi_ews_usbh_data);
-	/* I2C */
-	at91_add_device_i2c(rsi_ews_i2c_devices,
-			ARRAY_SIZE(rsi_ews_i2c_devices));
-	/* SPI */
-	at91_add_device_spi(rsi_ews_spi_devices,
-			ARRAY_SIZE(rsi_ews_spi_devices));
-	/* MMC */
-	at91_add_device_mci(0, &rsi_ews_mci0_data);
-	/* NOR Flash */
-	platform_device_register(&rsiews_nor_flash);
-	/* LEDs */
-	at91_gpio_leds(rsi_ews_leds, ARRAY_SIZE(rsi_ews_leds));
-}
-
-MACHINE_START(RSI_EWS, "RSI EWS")
-	/* Maintainer: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= rsi_ews_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= rsi_ews_board_init,
-MACHINE_END