Merge branch 'at91/cleanup5' into next/drivers

The at91 cleanups changed a lot of files, this merges in the
latest cleanups to resolve the conflicts

Conflicts:
	arch/arm/mach-at91/at91sam9260.c
	arch/arm/mach-at91/at91sam9261.c
	arch/arm/mach-at91/at91sam9263.c
	arch/arm/mach-at91/clock.c
	arch/arm/mach-at91/clock.h
	drivers/rtc/Kconfig

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

MAINTAINERS

@@ -861,6 +861,7 @@ W:	http://maxim.org.za/at91_26.html
 W:	http://www.linux4sam.org
 S:	Supported
 F:	arch/arm/mach-at91/
+F:	include/soc/at91/
 F:	arch/arm/boot/dts/at91*.dts
 F:	arch/arm/boot/dts/at91*.dtsi
 F:	arch/arm/boot/dts/sama*.dts

arch/arm/Kconfig

@@ -376,10 +376,11 @@ config ARCH_AT91
 	select IRQ_DOMAIN
 	select NEED_MACH_IO_H if PCCARD
 	select PINCTRL
-	select PINCTRL_AT91 if USE_OF
+	select PINCTRL_AT91
+	select USE_OF
 	help
 	  This enables support for systems based on Atmel
-	  AT91RM9200 and AT91SAM9* processors.
+	  AT91RM9200, AT91SAM9 and SAMA5 processors.
 
 config ARCH_CLPS711X
 	bool "Cirrus Logic CLPS711x/EP721x/EP731x-based"

arch/arm/configs/at91rm9200_defconfig

@@ -1,161 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_USER_NS=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_MODULE_SRCVERSION_ALL=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91RM9200=y
-CONFIG_MACH_ONEARM=y
-CONFIG_MACH_AT91RM9200EK=y
-CONFIG_MACH_CSB337=y
-CONFIG_MACH_CSB637=y
-CONFIG_MACH_CARMEVA=y
-CONFIG_MACH_ATEB9200=y
-CONFIG_MACH_KB9200=y
-CONFIG_MACH_PICOTUX2XX=y
-CONFIG_MACH_KAFA=y
-CONFIG_MACH_ECBAT91=y
-CONFIG_MACH_YL9200=y
-CONFIG_MACH_CPUAT91=y
-CONFIG_MACH_ECO920=y
-CONFIG_MTD_AT91_DATAFLASH_CARD=y
-CONFIG_AT91_TIMER_HZ=100
-# CONFIG_ARM_THUMB is not set
-CONFIG_PCCARD=y
-CONFIG_AT91_CF=y
-CONFIG_AEABI=y
-# CONFIG_COMPACTION is not set
-CONFIG_ZBOOT_ROM_TEXT=0x10000000
-CONFIG_ZBOOT_ROM_BSS=0x20040000
-CONFIG_KEXEC=y
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_MISC=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_DIAG is not set
-CONFIG_IPV6=y
-CONFIG_IPV6_PRIVACY=y
-CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-# CONFIG_STANDALONE is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PLATRAM=y
-CONFIG_MTD_DATAFLASH=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_NAND_PLATFORM=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_GLUEBI=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_NETDEVICES=y
-CONFIG_MII=y
-CONFIG_ARM_AT91_ETHER=y
-CONFIG_DAVICOM_PHY=y
-CONFIG_SMSC_PHY=y
-CONFIG_MICREL_PHY=y
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_GPIO=y
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=y
-CONFIG_GPIO_SYSFS=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_AT91RM9200_WATCHDOG=y
-CONFIG_FB=y
-CONFIG_FB_MODE_HELPERS=y
-CONFIG_FB_TILEBLITTING=y
-CONFIG_FB_S1D13XXX=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-# CONFIG_BACKLIGHT_GENERIC is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_LOGO=y
-CONFIG_USB=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_AT91=y
-CONFIG_USB_G_SERIAL=y
-CONFIG_MMC=y
-CONFIG_MMC_ATMELMCI=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_LEDS_TRIGGER_GPIO=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AT91RM9200=y
-CONFIG_EXT4_FS=y
-CONFIG_AUTOFS4_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_UBIFS_FS=y
-CONFIG_UBIFS_FS_ADVANCED_COMPR=y
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_UTF8=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_CRYPTO_PCBC=y
-CONFIG_CRYPTO_SHA1=y
-CONFIG_XZ_DEC_ARMTHUMB=y

arch/arm/configs/at91sam9260_9g20_defconfig

@@ -1,145 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EMBEDDED=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91SAM9260=y
-CONFIG_MACH_AT91SAM9260EK=y
-CONFIG_MACH_CAM60=y
-CONFIG_MACH_SAM9_L9260=y
-CONFIG_MACH_AFEB9260=y
-CONFIG_MACH_CPU9260=y
-CONFIG_MACH_FLEXIBITY=y
-CONFIG_MACH_AT91SAM9G20EK=y
-CONFIG_MACH_AT91SAM9G20EK_2MMC=y
-CONFIG_MACH_CPU9G20=y
-CONFIG_MACH_ACMENETUSFOXG20=y
-CONFIG_MACH_PORTUXG20=y
-CONFIG_MACH_STAMP9G20=y
-CONFIG_MACH_PCONTROL_G20=y
-CONFIG_MACH_GSIA18S=y
-CONFIG_MACH_SNAPPER_9260=y
-CONFIG_MACH_AT91SAM9_DT=y
-CONFIG_AT91_SLOW_CLOCK=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_ARM_ATAG_DTB_COMPAT=y
-CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_DATAFLASH=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_UBI=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_EEPROM_AT25=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-# CONFIG_SCSI_LOWLEVEL is not set
-CONFIG_NETDEVICES=y
-CONFIG_MACB=y
-# CONFIG_NET_VENDOR_BROADCOM is not set
-# CONFIG_NET_VENDOR_FARADAY is not set
-# CONFIG_NET_VENDOR_INTEL is not set
-# CONFIG_NET_VENDOR_MARVELL is not set
-# CONFIG_NET_VENDOR_MICREL is not set
-# CONFIG_NET_VENDOR_MICROCHIP is not set
-# CONFIG_NET_VENDOR_NATSEMI is not set
-# CONFIG_NET_VENDOR_SEEQ is not set
-# CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
-CONFIG_SMSC_PHY=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_GPIO=y
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=y
-CONFIG_SPI_SPIDEV=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_POWER_RESET=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_AT91SAM9X_WATCHDOG=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_SEQUENCER=y
-CONFIG_SND_MIXER_OSS=y
-CONFIG_SND_PCM_OSS=y
-CONFIG_SND_SEQUENCER_OSS=y
-# CONFIG_SND_VERBOSE_PROCFS is not set
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_AT91=y
-CONFIG_USB_G_SERIAL=y
-CONFIG_MMC=y
-CONFIG_MMC_ATMELMCI=y
-CONFIG_MMC_SPI=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_RV3029C2=y
-CONFIG_RTC_DRV_AT91SAM9=y
-CONFIG_IIO=y
-CONFIG_AT91_ADC=y
-CONFIG_EXT4_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_UBIFS_FS=y
-CONFIG_UBIFS_FS_ADVANCED_COMPR=y
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_15=y
-CONFIG_NLS_UTF8=y
-CONFIG_DEBUG_INFO=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_LL=y
-CONFIG_EARLY_PRINTK=y

arch/arm/configs/at91sam9261_9g10_defconfig

@@ -1,147 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_KERNEL_LZMA=y
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_NAMESPACES=y
-CONFIG_EMBEDDED=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91SAM9261=y
-CONFIG_MACH_AT91SAM9261EK=y
-CONFIG_MACH_AT91SAM9G10EK=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_VFP=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_CFG80211=y
-CONFIG_MAC80211=y
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_GLUEBI=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_ATMEL_TCLIB=y
-CONFIG_ATMEL_SSC=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_NETDEVICES=y
-CONFIG_DM9000=y
-CONFIG_USB_ZD1201=m
-CONFIG_RTL8187=m
-CONFIG_LIBERTAS=m
-CONFIG_LIBERTAS_USB=m
-CONFIG_LIBERTAS_SDIO=m
-CONFIG_LIBERTAS_SPI=m
-CONFIG_RT2X00=m
-CONFIG_RT2500USB=m
-CONFIG_RT73USB=m
-CONFIG_ZD1211RW=m
-CONFIG_INPUT_POLLDEV=m
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=240
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=320
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ADS7846=y
-CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_GPIO=y
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_POWER_RESET=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_AT91SAM9X_WATCHDOG=y
-CONFIG_FB=y
-CONFIG_FB_ATMEL=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-# CONFIG_LCD_CLASS_DEVICE is not set
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_ATMEL_LCDC=y
-# CONFIG_BACKLIGHT_GENERIC is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-CONFIG_LOGO=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_SEQUENCER=y
-CONFIG_SND_MIXER_OSS=y
-CONFIG_SND_PCM_OSS=y
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-CONFIG_SND_AT73C213=y
-CONFIG_SND_USB_AUDIO=m
-# CONFIG_USB_HID is not set
-CONFIG_USB=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_AT91=y
-CONFIG_USB_G_SERIAL=y
-CONFIG_MMC=y
-CONFIG_MMC_ATMELMCI=m
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_LEDS_TRIGGER_GPIO=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AT91SAM9=y
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_UBIFS_FS=y
-CONFIG_UBIFS_FS_ADVANCED_COMPR=y
-CONFIG_SQUASHFS=y
-CONFIG_SQUASHFS_LZO=y
-CONFIG_SQUASHFS_XZ=y
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_15=y
-CONFIG_NLS_UTF8=y
-CONFIG_CRC_CCITT=m

arch/arm/configs/at91sam9263_defconfig

@@ -1,151 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_NAMESPACES=y
-CONFIG_EMBEDDED=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91SAM9263=y
-CONFIG_MACH_AT91SAM9263EK=y
-CONFIG_MTD_AT91_DATAFLASH_CARD=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_NET_KEY=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_ADVANCED_ROUTER=y
-CONFIG_IP_ROUTE_VERBOSE=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-CONFIG_NET_IPIP=y
-CONFIG_IP_MROUTE=y
-CONFIG_IP_PIMSM_V1=y
-CONFIG_IP_PIMSM_V2=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-CONFIG_IPV6=y
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_NFTL=y
-CONFIG_NFTL_RW=y
-CONFIG_MTD_DATAFLASH=y
-CONFIG_MTD_BLOCK2MTD=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_GLUEBI=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_ATMEL_TCLIB=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_NETDEVICES=y
-CONFIG_MACB=y
-CONFIG_SMSC_PHY=y
-# CONFIG_WLAN is not set
-CONFIG_INPUT_POLLDEV=m
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ADS7846=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_GPIO=y
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_POWER_RESET=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_AT91SAM9X_WATCHDOG=y
-CONFIG_FB=y
-CONFIG_FB_ATMEL=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-CONFIG_LOGO=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_SEQUENCER=y
-CONFIG_SND_MIXER_OSS=y
-CONFIG_SND_PCM_OSS=y
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-CONFIG_SND_ATMEL_AC97C=y
-# CONFIG_SND_SPI is not set
-CONFIG_SND_USB_AUDIO=m
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_ATMEL_USBA=y
-CONFIG_USB_G_SERIAL=y
-CONFIG_MMC=y
-CONFIG_SDIO_UART=m
-CONFIG_MMC_ATMELMCI=m
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_PWM=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AT91SAM9=y
-CONFIG_PWM=y
-CONFIG_PWM_ATMEL=y
-CONFIG_EXT4_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_UBIFS_FS=y
-CONFIG_UBIFS_FS_ADVANCED_COMPR=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_UTF8=y
-CONFIG_DEBUG_USER=y
-CONFIG_XZ_DEC=y
-CONFIG_FONTS=y

arch/arm/configs/sama5_defconfig

@@ -20,7 +20,6 @@ CONFIG_ARCH_AT91=y
 CONFIG_SOC_SAM_V7=y
 CONFIG_SOC_SAMA5D3=y
 CONFIG_SOC_SAMA5D4=y
-CONFIG_MACH_SAMA5_DT=y
 CONFIG_AEABI=y
 CONFIG_UACCESS_WITH_MEMCPY=y
 CONFIG_ZBOOT_ROM_TEXT=0x0

arch/arm/mach-at91/Kconfig

@@ -15,23 +15,10 @@ config HAVE_AT91_DBGU1
 config HAVE_AT91_DBGU2
 	bool
 
-config AT91_USE_OLD_CLK
-	bool
-
 config COMMON_CLK_AT91
 	bool
-	default USE_OF && !AT91_USE_OLD_CLK
 	select COMMON_CLK
 
-config OLD_CLK_AT91
-	bool
-	default AT91_USE_OLD_CLK
-
-config OLD_IRQ_AT91
-	bool
-	select MULTI_IRQ_HANDLER
-	select SPARSE_IRQ
-
 config HAVE_AT91_SMD
 	bool
 
@@ -40,20 +27,22 @@ config HAVE_AT91_H32MX
 
 config SOC_AT91SAM9
 	bool
-	select ATMEL_AIC_IRQ if !OLD_IRQ_AT91
+	select ATMEL_AIC_IRQ
+	select COMMON_CLK_AT91
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
-	select MEMORY if USE_OF
-	select ATMEL_SDRAMC if USE_OF
+	select MEMORY
+	select ATMEL_SDRAMC
 
 config SOC_SAMA5
 	bool
 	select ATMEL_AIC5_IRQ
+	select COMMON_CLK_AT91
 	select CPU_V7
 	select GENERIC_CLOCKEVENTS
-	select USE_OF
 	select MEMORY
 	select ATMEL_SDRAMC
+	select PHYLIB if NETDEVICES
 
 menu "Atmel AT91 System-on-Chip"
 
@@ -108,7 +97,8 @@ endif
 if SOC_SAM_V4_V5
 config SOC_AT91RM9200
 	bool "AT91RM9200"
-	select ATMEL_AIC_IRQ if !OLD_IRQ_AT91
+	select ATMEL_AIC_IRQ
+	select COMMON_CLK_AT91
 	select CPU_ARM920T
 	select GENERIC_CLOCKEVENTS
 	select HAVE_AT91_DBGU0
@@ -184,37 +174,11 @@ config SOC_AT91SAM9N12
 # ----------------------------------------------------------
 endif # SOC_SAM_V4_V5
 
-
-if SOC_SAM_V4_V5
-source arch/arm/mach-at91/Kconfig.non_dt
-endif
-
-comment "Generic Board Type"
-
 config MACH_AT91RM9200_DT
-	bool "Atmel AT91RM9200 Evaluation Kits with device-tree support"
-	depends on SOC_AT91RM9200
-	select USE_OF
-	help
-	  Select this if you want to experiment device-tree with
-	  an Atmel RM9200 Evaluation Kit.
+	def_bool SOC_AT91RM9200
 
 config MACH_AT91SAM9_DT
-	bool "Atmel AT91SAM Evaluation Kits with device-tree support"
-	depends on SOC_AT91SAM9
-	select USE_OF
-	help
-	  Select this if you want to experiment device-tree with
-	  an Atmel Evaluation Kit.
-
-config MACH_SAMA5_DT
-	bool "Atmel SAMA5 Evaluation Kits with device-tree support"
-	depends on SOC_SAMA5
-	select USE_OF
-	select PHYLIB if NETDEVICES
-	help
-	  Select this if you want to experiment device-tree with
-	  an Atmel Evaluation Kit.
+	def_bool SOC_AT91SAM9
 
 # ----------------------------------------------------------
 
@@ -237,7 +201,7 @@ config AT91_TIMER_HZ
        int "Kernel HZ (jiffies per second)"
        range 32 1024
        depends on ARCH_AT91
-       default "128" if ARCH_AT91RM9200
+       default "128" if SOC_AT91RM9200
        default "100"
        help
 	  On AT91rm9200 chips where you're using a system clock derived

arch/arm/mach-at91/Kconfig.non_dt

@@ -1,286 +0,0 @@
-menu "Atmel Non-DT world"
-
-config HAVE_AT91_DATAFLASH_CARD
-	bool
-
-choice
-	prompt "Atmel AT91 Processor Devices for non DT boards"
-
-config ARCH_AT91_NONE
-	bool "None"
-
-config ARCH_AT91RM9200
-	bool "AT91RM9200"
-	select SOC_AT91RM9200
-	select AT91_USE_OLD_CLK
-	select OLD_IRQ_AT91
-
-config ARCH_AT91SAM9260
-	bool "AT91SAM9260 or AT91SAM9XE or AT91SAM9G20"
-	select SOC_AT91SAM9260
-	select AT91_USE_OLD_CLK
-	select OLD_IRQ_AT91
-
-config ARCH_AT91SAM9261
-	bool "AT91SAM9261 or AT91SAM9G10"
-	select SOC_AT91SAM9261
-	select AT91_USE_OLD_CLK
-	select OLD_IRQ_AT91
-
-config ARCH_AT91SAM9263
-	bool "AT91SAM9263"
-	select SOC_AT91SAM9263
-	select AT91_USE_OLD_CLK
-	select OLD_IRQ_AT91
-
-endchoice
-
-config ARCH_AT91SAM9G20
-	bool
-	select ARCH_AT91SAM9260
-
-config ARCH_AT91SAM9G10
-	bool
-	select ARCH_AT91SAM9261
-
-# ----------------------------------------------------------
-
-if ARCH_AT91RM9200
-
-comment "AT91RM9200 Board Type"
-
-config MACH_ONEARM
-	bool "Ajeco 1ARM Single Board Computer"
-	help
-	  Select this if you are using Ajeco's 1ARM Single Board Computer.
-	  <http://www.ajeco.fi/>
-
-config MACH_AT91RM9200EK
-	bool "Atmel AT91RM9200-EK Evaluation Kit"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using Atmel's AT91RM9200-EK Evaluation Kit.
-	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507>
-
-config MACH_CSB337
-	bool "Cogent CSB337"
-	help
-	  Select this if you are using Cogent's CSB337 board.
-	  <http://www.cogcomp.com/csb_csb337.htm>
-
-config MACH_CSB637
-	bool "Cogent CSB637"
-	help
-	  Select this if you are using Cogent's CSB637 board.
-	  <http://www.cogcomp.com/csb_csb637.htm>
-
-config MACH_CARMEVA
-	bool "Conitec ARM&EVA"
-	help
-	  Select this if you are using Conitec's AT91RM9200-MCU-Module.
-	  <http://www.conitec.net/english/linuxboard.php>
-
-config MACH_ATEB9200
-	bool "Embest ATEB9200"
-	help
-	  Select this if you are using Embest's ATEB9200 board.
-	  <http://www.embedinfo.com/english/product/ATEB9200.asp>
-
-config MACH_KB9200
-	bool "KwikByte KB920x"
-	help
-	  Select this if you are using KwikByte's KB920x board.
-	  <http://www.kwikbyte.com/KB9202.html>
-
-config MACH_PICOTUX2XX
-	bool "picotux 200"
-	help
-	  Select this if you are using a picotux 200.
-	  <http://www.picotux.com/>
-
-config MACH_KAFA
-	bool "Sperry-Sun KAFA board"
-	help
-	  Select this if you are using Sperry-Sun's KAFA board.
-
-config MACH_ECBAT91
-	bool "emQbit ECB_AT91 SBC"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using emQbit's ECB_AT91 board.
-	  <http://wiki.emqbit.com/free-ecb-at91>
-
-config MACH_YL9200
-	bool "ucDragon YL-9200"
-	help
-	  Select this if you are using the ucDragon YL-9200 board.
-
-config MACH_CPUAT91
-	bool "Eukrea CPUAT91"
-	help
-	  Select this if you are using the Eukrea Electromatique's
-	  CPUAT91 board <http://www.eukrea.com/>.
-
-config MACH_ECO920
-	bool "eco920"
-	help
-	  Select this if you are using the eco920 board
-endif
-
-# ----------------------------------------------------------
-
-if ARCH_AT91SAM9260
-
-comment "AT91SAM9260 Variants"
-
-comment "AT91SAM9260 / AT91SAM9XE Board Type"
-
-config MACH_AT91SAM9260EK
-	bool "Atmel AT91SAM9260-EK / AT91SAM9XE Evaluation Kit"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit
-	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933>
-
-config MACH_CAM60
-	bool "KwikByte KB9260 (CAM60) board"
-	help
-	  Select this if you are using KwikByte's KB9260 (CAM60) board based on the Atmel AT91SAM9260.
-	  <http://www.kwikbyte.com/KB9260.html>
-
-config MACH_SAM9_L9260
-	bool "Olimex SAM9-L9260 board"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using Olimex's SAM9-L9260 board based on the Atmel AT91SAM9260.
-	  <http://www.olimex.com/dev/sam9-L9260.html>
-
-config MACH_AFEB9260
-	bool "Custom afeb9260 board v1"
-	help
-	  Select this if you are using custom afeb9260 board based on
-	  open hardware design. Select this for revision 1 of the board.
-	  <svn://194.85.238.22/home/users/george/svn/arm9eb>
-	  <http://groups.google.com/group/arm9fpga-evolution-board>
-
-config MACH_CPU9260
-	bool "Eukrea CPU9260 board"
-	help
-	  Select this if you are using a Eukrea Electromatique's
-	  CPU9260 Board <http://www.eukrea.com/>
-
-config MACH_FLEXIBITY
-	bool "Flexibity Connect board"
-	help
-	  Select this if you are using Flexibity Connect board
-	  <http://www.flexibity.com>
-
-comment "AT91SAM9G20 Board Type"
-
-config MACH_AT91SAM9G20EK
-	bool "Atmel AT91SAM9G20-EK Evaluation Kit"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit
-	  that embeds only one SD/MMC slot.
-
-config MACH_AT91SAM9G20EK_2MMC
-	depends on MACH_AT91SAM9G20EK
-	bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots"
-	help
-	  Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit
-	  with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and
-	  onwards.
-	  <http://www.atmel.com/tools/SAM9G20-EK.aspx>
-
-config MACH_CPU9G20
-	bool "Eukrea CPU9G20 board"
-	help
-	  Select this if you are using a Eukrea Electromatique's
-	  CPU9G20 Board <http://www.eukrea.com/>
-
-config MACH_PORTUXG20
-	bool "taskit PortuxG20"
-	help
-	  Select this if you are using taskit's PortuxG20.
-	  <http://www.taskit.de/en/>
-
-config MACH_STAMP9G20
-	bool "taskit Stamp9G20 CPU module"
-	help
-	  Select this if you are using taskit's Stamp9G20 CPU module on its
-	  evaluation board.
-	  <http://www.taskit.de/en/>
-
-config MACH_PCONTROL_G20
-	bool "PControl G20 CPU module"
-	help
-	  Select this if you are using taskit's Stamp9G20 CPU module on this
-	  carrier board, being the decentralized unit of a building automation
-	  system; featuring nvram, eth-switch, iso-rs485, display, io
-
-config MACH_GSIA18S
-	bool "GS_IA18_S board"
-	help
-	  This enables support for the GS_IA18_S board
-	  produced by GeoSIG Ltd company. This is an internet accelerograph.
-	  <http://www.geosig.com>
-
-config MACH_SNAPPER_9260
-	bool "Bluewater Systems Snapper 9260/9G20 module"
-	help
-	  Select this if you are using the Bluewater Systems Snapper 9260 or
-	  Snapper 9G20 modules.
-	  <http://www.bluewatersys.com/>
-endif
-
-# ----------------------------------------------------------
-
-if ARCH_AT91SAM9261
-
-comment "AT91SAM9261 Board Type"
-
-config MACH_AT91SAM9261EK
-	bool "Atmel AT91SAM9261-EK Evaluation Kit"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using Atmel's AT91SAM9261-EK Evaluation Kit.
-	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3820>
-
-comment "AT91SAM9G10 Board Type"
-
-config MACH_AT91SAM9G10EK
-	bool "Atmel AT91SAM9G10-EK Evaluation Kit"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using Atmel's AT91SAM9G10-EK Evaluation Kit.
-	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4588>
-
-endif
-
-# ----------------------------------------------------------
-
-if ARCH_AT91SAM9263
-
-comment "AT91SAM9263 Board Type"
-
-config MACH_AT91SAM9263EK
-	bool "Atmel AT91SAM9263-EK Evaluation Kit"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit.
-	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057>
-
-endif
-
-# ----------------------------------------------------------
-
-comment "AT91 Board Options"
-
-config MTD_AT91_DATAFLASH_CARD
-	bool "Enable DataFlash Card support"
-	depends on HAVE_AT91_DATAFLASH_CARD
-	help
-	  Enable support for the DataFlash card.
-
-endmenu

arch/arm/mach-at91/Makefile

@@ -2,10 +2,8 @@
 # Makefile for the linux kernel.
 #
 
-obj-y		:= gpio.o setup.o sysirq_mask.o
+obj-y		:= setup.o sysirq_mask.o
 
-obj-$(CONFIG_OLD_IRQ_AT91)	+= irq.o
-obj-$(CONFIG_OLD_CLK_AT91)	+= clock.o
 obj-$(CONFIG_SOC_AT91SAM9)	+= sam9_smc.o
 
 # CPU-specific support
@@ -20,61 +18,12 @@ obj-$(CONFIG_SOC_AT91SAM9RL)	+= at91sam9rl.o
 obj-$(CONFIG_SOC_SAMA5D3)	+= sama5d3.o
 obj-$(CONFIG_SOC_SAMA5D4)	+= sama5d4.o
 
-obj-$(CONFIG_ARCH_AT91RM9200)	+= at91rm9200_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263_devices.o
-
-# AT91RM9200 board-specific support
-obj-$(CONFIG_MACH_ONEARM)	+= board-1arm.o
-obj-$(CONFIG_MACH_AT91RM9200EK)	+= board-rm9200ek.o
-obj-$(CONFIG_MACH_CSB337)	+= board-csb337.o
-obj-$(CONFIG_MACH_CSB637)	+= board-csb637.o
-obj-$(CONFIG_MACH_CARMEVA)	+= board-carmeva.o
-obj-$(CONFIG_MACH_KB9200)	+= board-kb9202.o
-obj-$(CONFIG_MACH_ATEB9200)	+= board-eb9200.o
-obj-$(CONFIG_MACH_KAFA)		+= board-kafa.o
-obj-$(CONFIG_MACH_PICOTUX2XX)	+= board-picotux200.o
-obj-$(CONFIG_MACH_ECBAT91)	+= board-ecbat91.o
-obj-$(CONFIG_MACH_YL9200)	+= board-yl-9200.o
-obj-$(CONFIG_MACH_CPUAT91)	+= board-cpuat91.o
-obj-$(CONFIG_MACH_ECO920)	+= board-eco920.o
-
-# AT91SAM9260 board-specific support
-obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
-obj-$(CONFIG_MACH_CAM60)	+= board-cam60.o
-obj-$(CONFIG_MACH_SAM9_L9260)	+= board-sam9-l9260.o
-obj-$(CONFIG_MACH_AFEB9260)	+= board-afeb-9260v1.o
-obj-$(CONFIG_MACH_CPU9260)	+= board-cpu9krea.o
-obj-$(CONFIG_MACH_FLEXIBITY)	+= board-flexibity.o
-
-# AT91SAM9261 board-specific support
-obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
-obj-$(CONFIG_MACH_AT91SAM9G10EK) += board-sam9261ek.o
-
-# AT91SAM9263 board-specific support
-obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
-
-# AT91SAM9G20 board-specific support
-obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
-obj-$(CONFIG_MACH_CPU9G20)	+= board-cpu9krea.o
-obj-$(CONFIG_MACH_STAMP9G20)	+= board-stamp9g20.o
-obj-$(CONFIG_MACH_PORTUXG20)	+= board-stamp9g20.o
-obj-$(CONFIG_MACH_PCONTROL_G20)	+= board-pcontrol-g20.o board-stamp9g20.o
-obj-$(CONFIG_MACH_GSIA18S)	+= board-gsia18s.o board-stamp9g20.o
-
-# AT91SAM9260/AT91SAM9G20 board-specific support
-obj-$(CONFIG_MACH_SNAPPER_9260)	+= board-snapper9260.o
-
 # AT91SAM board with device-tree
 obj-$(CONFIG_MACH_AT91RM9200_DT) += board-dt-rm9200.o
 obj-$(CONFIG_MACH_AT91SAM9_DT) += board-dt-sam9.o
 
 # SAMA5 board with device-tree
-obj-$(CONFIG_MACH_SAMA5_DT) += board-dt-sama5.o
-
-# Drivers
-obj-y				+= leds.o
+obj-$(CONFIG_SOC_SAMA5)		+= board-dt-sama5.o
 
 # Power Management
 obj-$(CONFIG_PM)		+= pm.o

arch/arm/mach-at91/Makefile.boot

@@ -3,12 +3,6 @@
 #   PARAMS_PHYS must be within 4MB of ZRELADDR
 #   INITRD_PHYS must be in RAM
 
-ifeq ($(CONFIG_ARCH_AT91SAM9G45),y)
-   zreladdr-y	+= 0x70008000
-params_phys-y	:= 0x70000100
-initrd_phys-y	:= 0x70410000
-else
    zreladdr-y	+= 0x20008000
 params_phys-y	:= 0x20000100
 initrd_phys-y	:= 0x20410000
-endif

arch/arm/mach-at91/at91_aic.h

@@ -1,99 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91_aic.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * Advanced Interrupt Controller (AIC) - System peripherals registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91_AIC_H
-#define AT91_AIC_H
-
-#ifndef __ASSEMBLY__
-extern void __iomem *at91_aic_base;
-
-#define at91_aic_read(field) \
-	__raw_readl(at91_aic_base + field)
-
-#define at91_aic_write(field, value) \
-	__raw_writel(value, at91_aic_base + field)
-#else
-.extern at91_aic_base
-#endif
-
-/* Number of irq lines managed by AIC */
-#define NR_AIC_IRQS	32
-#define NR_AIC5_IRQS	128
-
-#define AT91_AIC5_SSR		0x0			/* Source Select Register [AIC5] */
-#define 	AT91_AIC5_INTSEL_MSK	(0x7f << 0)		/* Interrupt Line Selection Mask */
-
-#define AT91_AIC_IRQ_MIN_PRIORITY	0
-#define AT91_AIC_IRQ_MAX_PRIORITY	7
-
-#define AT91_AIC_SMR(n)		((n) * 4)		/* Source Mode Registers 0-31 */
-#define AT91_AIC5_SMR		0x4			/* Source Mode Register [AIC5] */
-#define		AT91_AIC_PRIOR		(7 << 0)		/* Priority Level */
-#define		AT91_AIC_SRCTYPE	(3 << 5)		/* Interrupt Source Type */
-#define			AT91_AIC_SRCTYPE_LOW		(0 << 5)
-#define			AT91_AIC_SRCTYPE_FALLING	(1 << 5)
-#define			AT91_AIC_SRCTYPE_HIGH		(2 << 5)
-#define			AT91_AIC_SRCTYPE_RISING		(3 << 5)
-
-#define AT91_AIC_SVR(n)		(0x80 + ((n) * 4))	/* Source Vector Registers 0-31 */
-#define AT91_AIC5_SVR		0x8			/* Source Vector Register [AIC5] */
-#define AT91_AIC_IVR		0x100			/* Interrupt Vector Register */
-#define AT91_AIC5_IVR		0x10			/* Interrupt Vector Register [AIC5] */
-#define AT91_AIC_FVR		0x104			/* Fast Interrupt Vector Register */
-#define AT91_AIC5_FVR		0x14			/* Fast Interrupt Vector Register [AIC5] */
-#define AT91_AIC_ISR		0x108			/* Interrupt Status Register */
-#define AT91_AIC5_ISR		0x18			/* Interrupt Status Register [AIC5] */
-#define		AT91_AIC_IRQID		(0x1f << 0)		/* Current Interrupt Identifier */
-
-#define AT91_AIC_IPR		0x10c			/* Interrupt Pending Register */
-#define AT91_AIC5_IPR0		0x20			/* Interrupt Pending Register 0 [AIC5] */
-#define AT91_AIC5_IPR1		0x24			/* Interrupt Pending Register 1 [AIC5] */
-#define AT91_AIC5_IPR2		0x28			/* Interrupt Pending Register 2 [AIC5] */
-#define AT91_AIC5_IPR3		0x2c			/* Interrupt Pending Register 3 [AIC5] */
-#define AT91_AIC_IMR		0x110			/* Interrupt Mask Register */
-#define AT91_AIC5_IMR		0x30			/* Interrupt Mask Register [AIC5] */
-#define AT91_AIC_CISR		0x114			/* Core Interrupt Status Register */
-#define AT91_AIC5_CISR		0x34			/* Core Interrupt Status Register [AIC5] */
-#define		AT91_AIC_NFIQ		(1 << 0)		/* nFIQ Status */
-#define		AT91_AIC_NIRQ		(1 << 1)		/* nIRQ Status */
-
-#define AT91_AIC_IECR		0x120			/* Interrupt Enable Command Register */
-#define AT91_AIC5_IECR		0x40			/* Interrupt Enable Command Register [AIC5] */
-#define AT91_AIC_IDCR		0x124			/* Interrupt Disable Command Register */
-#define AT91_AIC5_IDCR		0x44			/* Interrupt Disable Command Register [AIC5] */
-#define AT91_AIC_ICCR		0x128			/* Interrupt Clear Command Register */
-#define AT91_AIC5_ICCR		0x48			/* Interrupt Clear Command Register [AIC5] */
-#define AT91_AIC_ISCR		0x12c			/* Interrupt Set Command Register */
-#define AT91_AIC5_ISCR		0x4c			/* Interrupt Set Command Register [AIC5] */
-#define AT91_AIC_EOICR		0x130			/* End of Interrupt Command Register */
-#define AT91_AIC5_EOICR		0x38			/* End of Interrupt Command Register [AIC5] */
-#define AT91_AIC_SPU		0x134			/* Spurious Interrupt Vector Register */
-#define AT91_AIC5_SPU		0x3c			/* Spurious Interrupt Vector Register [AIC5] */
-#define AT91_AIC_DCR		0x138			/* Debug Control Register */
-#define AT91_AIC5_DCR		0x6c			/* Debug Control Register [AIC5] */
-#define		AT91_AIC_DCR_PROT	(1 << 0)		/* Protection Mode */
-#define		AT91_AIC_DCR_GMSK	(1 << 1)		/* General Mask */
-
-#define AT91_AIC_FFER		0x140			/* Fast Forcing Enable Register [SAM9 only] */
-#define AT91_AIC5_FFER		0x50			/* Fast Forcing Enable Register [AIC5] */
-#define AT91_AIC_FFDR		0x144			/* Fast Forcing Disable Register [SAM9 only] */
-#define AT91_AIC5_FFDR		0x54			/* Fast Forcing Disable Register [AIC5] */
-#define AT91_AIC_FFSR		0x148			/* Fast Forcing Status Register [SAM9 only] */
-#define AT91_AIC5_FFSR		0x58			/* Fast Forcing Status Register [AIC5] */
-
-void at91_aic_handle_irq(struct pt_regs *regs);
-void at91_aic5_handle_irq(struct pt_regs *regs);
-
-#endif

arch/arm/mach-at91/at91_tc.h

@@ -1,146 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91_tc.h
- *
- * Copyright (C) SAN People
- *
- * Timer/Counter Unit (TC) registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91_TC_H
-#define AT91_TC_H
-
-#define AT91_TC_BCR		0xc0		/* TC Block Control Register */
-#define		AT91_TC_SYNC		(1 << 0)	/* Synchro Command */
-
-#define AT91_TC_BMR		0xc4		/* TC Block Mode Register */
-#define		AT91_TC_TC0XC0S		(3 << 0)	/* External Clock Signal 0 Selection */
-#define			AT91_TC_TC0XC0S_TCLK0		(0 << 0)
-#define			AT91_TC_TC0XC0S_NONE		(1 << 0)
-#define			AT91_TC_TC0XC0S_TIOA1		(2 << 0)
-#define			AT91_TC_TC0XC0S_TIOA2		(3 << 0)
-#define		AT91_TC_TC1XC1S		(3 << 2)	/* External Clock Signal 1 Selection */
-#define			AT91_TC_TC1XC1S_TCLK1		(0 << 2)
-#define			AT91_TC_TC1XC1S_NONE		(1 << 2)
-#define			AT91_TC_TC1XC1S_TIOA0		(2 << 2)
-#define			AT91_TC_TC1XC1S_TIOA2		(3 << 2)
-#define		AT91_TC_TC2XC2S		(3 << 4)	/* External Clock Signal 2 Selection */
-#define			AT91_TC_TC2XC2S_TCLK2		(0 << 4)
-#define			AT91_TC_TC2XC2S_NONE		(1 << 4)
-#define			AT91_TC_TC2XC2S_TIOA0		(2 << 4)
-#define			AT91_TC_TC2XC2S_TIOA1		(3 << 4)
-
-
-#define AT91_TC_CCR		0x00		/* Channel Control Register */
-#define		AT91_TC_CLKEN		(1 << 0)	/* Counter Clock Enable Command */
-#define		AT91_TC_CLKDIS		(1 << 1)	/* Counter CLock Disable Command */
-#define		AT91_TC_SWTRG		(1 << 2)	/* Software Trigger Command */
-
-#define AT91_TC_CMR		0x04		/* Channel Mode Register */
-#define		AT91_TC_TCCLKS		(7 << 0)	/* Capture/Waveform Mode: Clock Selection */
-#define			AT91_TC_TIMER_CLOCK1		(0 << 0)
-#define			AT91_TC_TIMER_CLOCK2		(1 << 0)
-#define			AT91_TC_TIMER_CLOCK3		(2 << 0)
-#define			AT91_TC_TIMER_CLOCK4		(3 << 0)
-#define			AT91_TC_TIMER_CLOCK5		(4 << 0)
-#define			AT91_TC_XC0			(5 << 0)
-#define			AT91_TC_XC1			(6 << 0)
-#define			AT91_TC_XC2			(7 << 0)
-#define		AT91_TC_CLKI		(1 << 3)	/* Capture/Waveform Mode: Clock Invert */
-#define		AT91_TC_BURST		(3 << 4)	/* Capture/Waveform Mode: Burst Signal Selection */
-#define		AT91_TC_LDBSTOP		(1 << 6)	/* Capture Mode: Counter Clock Stopped with TB Loading */
-#define		AT91_TC_LDBDIS		(1 << 7)	/* Capture Mode: Counter Clock Disable with RB Loading */
-#define		AT91_TC_ETRGEDG		(3 << 8)	/* Capture Mode: External Trigger Edge Selection */
-#define		AT91_TC_ABETRG		(1 << 10)	/* Capture Mode: TIOA or TIOB External Trigger Selection */
-#define		AT91_TC_CPCTRG		(1 << 14)	/* Capture Mode: RC Compare Trigger Enable */
-#define		AT91_TC_WAVE		(1 << 15)	/* Capture/Waveform mode */
-#define		AT91_TC_LDRA		(3 << 16)	/* Capture Mode: RA Loading Selection */
-#define		AT91_TC_LDRB		(3 << 18)	/* Capture Mode: RB Loading Selection */
-
-#define		AT91_TC_CPCSTOP		(1 <<  6)	/* Waveform Mode: Counter Clock Stopped with RC Compare */
-#define		AT91_TC_CPCDIS		(1 <<  7)	/* Waveform Mode: Counter Clock Disable with RC Compare */
-#define		AT91_TC_EEVTEDG		(3 <<  8)	/* Waveform Mode: External Event Edge Selection */
-#define			AT91_TC_EEVTEDG_NONE		(0 << 8)
-#define			AT91_TC_EEVTEDG_RISING		(1 << 8)
-#define			AT91_TC_EEVTEDG_FALLING		(2 << 8)
-#define			AT91_TC_EEVTEDG_BOTH		(3 << 8)
-#define		AT91_TC_EEVT		(3 << 10)	/* Waveform Mode: External Event Selection */
-#define			AT91_TC_EEVT_TIOB		(0 << 10)
-#define			AT91_TC_EEVT_XC0		(1 << 10)
-#define			AT91_TC_EEVT_XC1		(2 << 10)
-#define			AT91_TC_EEVT_XC2		(3 << 10)
-#define		AT91_TC_ENETRG		(1 << 12)	/* Waveform Mode: External Event Trigger Enable */
-#define		AT91_TC_WAVESEL		(3 << 13)	/* Waveform Mode: Waveform Selection */
-#define			AT91_TC_WAVESEL_UP		(0 << 13)
-#define			AT91_TC_WAVESEL_UP_AUTO		(2 << 13)
-#define			AT91_TC_WAVESEL_UPDOWN		(1 << 13)
-#define			AT91_TC_WAVESEL_UPDOWN_AUTO	(3 << 13)
-#define		AT91_TC_ACPA		(3 << 16)	/* Waveform Mode: RA Compare Effect on TIOA */
-#define			AT91_TC_ACPA_NONE		(0 << 16)
-#define			AT91_TC_ACPA_SET		(1 << 16)
-#define			AT91_TC_ACPA_CLEAR		(2 << 16)
-#define			AT91_TC_ACPA_TOGGLE		(3 << 16)
-#define		AT91_TC_ACPC		(3 << 18)	/* Waveform Mode: RC Compre Effect on TIOA */
-#define			AT91_TC_ACPC_NONE		(0 << 18)
-#define			AT91_TC_ACPC_SET		(1 << 18)
-#define			AT91_TC_ACPC_CLEAR		(2 << 18)
-#define			AT91_TC_ACPC_TOGGLE		(3 << 18)
-#define		AT91_TC_AEEVT		(3 << 20)	/* Waveform Mode: External Event Effect on TIOA */
-#define			AT91_TC_AEEVT_NONE		(0 << 20)
-#define			AT91_TC_AEEVT_SET		(1 << 20)
-#define			AT91_TC_AEEVT_CLEAR		(2 << 20)
-#define			AT91_TC_AEEVT_TOGGLE		(3 << 20)
-#define		AT91_TC_ASWTRG		(3 << 22)	/* Waveform Mode: Software Trigger Effect on TIOA */
-#define			AT91_TC_ASWTRG_NONE		(0 << 22)
-#define			AT91_TC_ASWTRG_SET		(1 << 22)
-#define			AT91_TC_ASWTRG_CLEAR		(2 << 22)
-#define			AT91_TC_ASWTRG_TOGGLE		(3 << 22)
-#define		AT91_TC_BCPB		(3 << 24)	/* Waveform Mode: RB Compare Effect on TIOB */
-#define			AT91_TC_BCPB_NONE		(0 << 24)
-#define			AT91_TC_BCPB_SET		(1 << 24)
-#define			AT91_TC_BCPB_CLEAR		(2 << 24)
-#define			AT91_TC_BCPB_TOGGLE		(3 << 24)
-#define		AT91_TC_BCPC		(3 << 26)	/* Waveform Mode: RC Compare Effect on TIOB */
-#define			AT91_TC_BCPC_NONE		(0 << 26)
-#define			AT91_TC_BCPC_SET		(1 << 26)
-#define			AT91_TC_BCPC_CLEAR		(2 << 26)
-#define			AT91_TC_BCPC_TOGGLE		(3 << 26)
-#define		AT91_TC_BEEVT		(3 << 28)	/* Waveform Mode: External Event Effect on TIOB */
-#define			AT91_TC_BEEVT_NONE		(0 << 28)
-#define			AT91_TC_BEEVT_SET		(1 << 28)
-#define			AT91_TC_BEEVT_CLEAR		(2 << 28)
-#define			AT91_TC_BEEVT_TOGGLE		(3 << 28)
-#define		AT91_TC_BSWTRG		(3 << 30)	/* Waveform Mode: Software Trigger Effect on TIOB */
-#define			AT91_TC_BSWTRG_NONE		(0 << 30)
-#define			AT91_TC_BSWTRG_SET		(1 << 30)
-#define			AT91_TC_BSWTRG_CLEAR		(2 << 30)
-#define			AT91_TC_BSWTRG_TOGGLE		(3 << 30)
-
-#define AT91_TC_CV		0x10		/* Counter Value */
-#define AT91_TC_RA		0x14		/* Register A */
-#define AT91_TC_RB		0x18		/* Register B */
-#define AT91_TC_RC		0x1c		/* Register C */
-
-#define AT91_TC_SR		0x20		/* Status Register */
-#define		AT91_TC_COVFS		(1 <<  0)	/* Counter Overflow Status */
-#define		AT91_TC_LOVRS		(1 <<  1)	/* Load Overrun Status */
-#define		AT91_TC_CPAS		(1 <<  2)	/* RA Compare Status */
-#define		AT91_TC_CPBS		(1 <<  3)	/* RB Compare Status */
-#define		AT91_TC_CPCS		(1 <<  4)	/* RC Compare Status */
-#define		AT91_TC_LDRAS		(1 <<  5)	/* RA Loading Status */
-#define		AT91_TC_LDRBS		(1 <<  6)	/* RB Loading Status */
-#define		AT91_TC_ETRGS		(1 <<  7)	/* External Trigger Status */
-#define		AT91_TC_CLKSTA		(1 << 16)	/* Clock Enabling Status */
-#define		AT91_TC_MTIOA		(1 << 17)	/* TIOA Mirror */
-#define		AT91_TC_MTIOB		(1 << 18)	/* TIOB Mirror */
-
-#define AT91_TC_IER		0x24		/* Interrupt Enable Register */
-#define AT91_TC_IDR		0x28		/* Interrupt Disable Register */
-#define AT91_TC_IMR		0x2c		/* Interrupt Mask Register */
-
-#endif

arch/arm/mach-at91/at91rm9200.c

@@ -11,296 +11,15 @@
  */
 
 #include <linux/module.h>
-#include <linux/reboot.h>
 #include <linux/clk/at91_pmc.h>
 
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <asm/system_misc.h>
-#include <mach/at91rm9200.h>
 #include <mach/at91_st.h>
-#include <mach/cpu.h>
 #include <mach/hardware.h>
 
-#include "at91_aic.h"
 #include "soc.h"
 #include "generic.h"
-#include "sam9_smc.h"
-#include "pm.h"
-
-#if defined(CONFIG_OLD_CLK_AT91)
-#include "clock.h"
-/* --------------------------------------------------------------------
- *  Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk udc_clk = {
-	.name		= "udc_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_UDP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ohci_clk = {
-	.name		= "ohci_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_UHP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ether_clk = {
-	.name		= "ether_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_EMAC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc_clk = {
-	.name		= "mci_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_MCI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi_clk = {
-	.name		= "twi_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_TWI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
-	.name		= "usart0_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_US0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
-	.name		= "usart1_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_US1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
-	.name		= "usart2_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_US2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart3_clk = {
-	.name		= "usart3_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_US3,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi_clk = {
-	.name		= "spi_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_SPI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioA_clk = {
-	.name		= "pioA_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_PIOA,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioB_clk = {
-	.name		= "pioB_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_PIOB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioC_clk = {
-	.name		= "pioC_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_PIOC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioD_clk = {
-	.name		= "pioD_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_PIOD,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc0_clk = {
-	.name		= "ssc0_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_SSC0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc1_clk = {
-	.name		= "ssc1_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_SSC1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc2_clk = {
-	.name		= "ssc2_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_SSC2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc0_clk = {
-	.name		= "tc0_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_TC0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc1_clk = {
-	.name		= "tc1_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_TC1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc2_clk = {
-	.name		= "tc2_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_TC2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc3_clk = {
-	.name		= "tc3_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_TC3,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc4_clk = {
-	.name		= "tc4_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_TC4,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc5_clk = {
-	.name		= "tc5_clk",
-	.pmc_mask	= 1 << AT91RM9200_ID_TC5,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk *periph_clocks[] __initdata = {
-	&pioA_clk,
-	&pioB_clk,
-	&pioC_clk,
-	&pioD_clk,
-	&usart0_clk,
-	&usart1_clk,
-	&usart2_clk,
-	&usart3_clk,
-	&mmc_clk,
-	&udc_clk,
-	&twi_clk,
-	&spi_clk,
-	&ssc0_clk,
-	&ssc1_clk,
-	&ssc2_clk,
-	&tc0_clk,
-	&tc1_clk,
-	&tc2_clk,
-	&tc3_clk,
-	&tc4_clk,
-	&tc5_clk,
-	&ohci_clk,
-	&ether_clk,
-	// irq0 .. irq6
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.1", &tc3_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.1", &tc4_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.1", &tc5_clk),
-	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.0", &ssc0_clk),
-	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.1", &ssc1_clk),
-	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.2", &ssc2_clk),
-	CLKDEV_CON_DEV_ID("pclk", "fffd0000.ssc", &ssc0_clk),
-	CLKDEV_CON_DEV_ID("pclk", "fffd4000.ssc", &ssc1_clk),
-	CLKDEV_CON_DEV_ID("pclk", "fffd8000.ssc", &ssc2_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91rm9200.0", &twi_clk),
-	/* fake hclk clock */
-	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
-	CLKDEV_CON_ID("pioA", &pioA_clk),
-	CLKDEV_CON_ID("pioB", &pioB_clk),
-	CLKDEV_CON_ID("pioC", &pioC_clk),
-	CLKDEV_CON_ID("pioD", &pioD_clk),
-	/* usart lookup table for DT entries */
-	CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
-	CLKDEV_CON_DEV_ID("usart", "fffc0000.serial", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "fffc4000.serial", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "fffc8000.serial", &usart2_clk),
-	CLKDEV_CON_DEV_ID("usart", "fffcc000.serial", &usart3_clk),
-	/* tc lookup table for DT entries */
-	CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "fffa0000.timer", &tc1_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "fffa0000.timer", &tc2_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "fffa4000.timer", &tc3_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "fffa4000.timer", &tc4_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "fffa4000.timer", &tc5_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "fffb4000.mmc", &mmc_clk),
-	CLKDEV_CON_DEV_ID("emac_clk", "fffbc000.ethernet", &ether_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffb8000.i2c", &twi_clk),
-	CLKDEV_CON_DEV_ID("hclk", "300000.ohci", &ohci_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioD_clk),
-};
-
-static struct clk_lookup usart_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.4", &usart3_clk),
-};
-
-/*
- * The four programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
-	.name		= "pck0",
-	.pmc_mask	= AT91_PMC_PCK0,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 0,
-};
-static struct clk pck1 = {
-	.name		= "pck1",
-	.pmc_mask	= AT91_PMC_PCK1,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 1,
-};
-static struct clk pck2 = {
-	.name		= "pck2",
-	.pmc_mask	= AT91_PMC_PCK2,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 2,
-};
-static struct clk pck3 = {
-	.name		= "pck3",
-	.pmc_mask	= AT91_PMC_PCK3,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 3,
-};
-
-static void __init at91rm9200_register_clocks(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
-		clk_register(periph_clocks[i]);
-
-	clkdev_add_table(periph_clocks_lookups,
-			 ARRAY_SIZE(periph_clocks_lookups));
-	clkdev_add_table(usart_clocks_lookups,
-			 ARRAY_SIZE(usart_clocks_lookups));
-
-	clk_register(&pck0);
-	clk_register(&pck1);
-	clk_register(&pck2);
-	clk_register(&pck3);
-}
-#else
-#define at91rm9200_register_clocks NULL
-#endif
-
-/* --------------------------------------------------------------------
- *  GPIO
- * -------------------------------------------------------------------- */
-
-static struct at91_gpio_bank at91rm9200_gpio[] __initdata = {
-	{
-		.id		= AT91RM9200_ID_PIOA,
-		.regbase	= AT91RM9200_BASE_PIOA,
-	}, {
-		.id		= AT91RM9200_ID_PIOB,
-		.regbase	= AT91RM9200_BASE_PIOB,
-	}, {
-		.id		= AT91RM9200_ID_PIOC,
-		.regbase	= AT91RM9200_BASE_PIOC,
-	}, {
-		.id		= AT91RM9200_ID_PIOD,
-		.regbase	= AT91RM9200_BASE_PIOD,
-	}
-};
 
 static void at91rm9200_idle(void)
 {
@@ -329,74 +48,14 @@ static void __init at91rm9200_map_io(void)
 	at91_init_sram(0, AT91RM9200_SRAM_BASE, AT91RM9200_SRAM_SIZE);
 }
 
-static void __init at91rm9200_ioremap_registers(void)
-{
-	at91rm9200_ioremap_st(AT91RM9200_BASE_ST);
-	at91_ioremap_ramc(0, AT91RM9200_BASE_MC, 256);
-	at91_pm_set_standby(at91rm9200_standby);
-}
-
 static void __init at91rm9200_initialize(void)
 {
 	arm_pm_idle = at91rm9200_idle;
 	arm_pm_restart = at91rm9200_restart;
-
-	/* Initialize GPIO subsystem */
-	at91_gpio_init(at91rm9200_gpio,
-		cpu_is_at91rm9200_bga() ? AT91RM9200_BGA : AT91RM9200_PQFP);
 }
 
 
-/* --------------------------------------------------------------------
- *  Interrupt initialization
- * -------------------------------------------------------------------- */
-
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = {
-	7,	/* Advanced Interrupt Controller (FIQ) */
-	7,	/* System Peripherals */
-	1,	/* Parallel IO Controller A */
-	1,	/* Parallel IO Controller B */
-	1,	/* Parallel IO Controller C */
-	1,	/* Parallel IO Controller D */
-	5,	/* USART 0 */
-	5,	/* USART 1 */
-	5,	/* USART 2 */
-	5,	/* USART 3 */
-	0,	/* Multimedia Card Interface */
-	2,	/* USB Device Port */
-	6,	/* Two-Wire Interface */
-	5,	/* Serial Peripheral Interface */
-	4,	/* Serial Synchronous Controller 0 */
-	4,	/* Serial Synchronous Controller 1 */
-	4,	/* Serial Synchronous Controller 2 */
-	0,	/* Timer Counter 0 */
-	0,	/* Timer Counter 1 */
-	0,	/* Timer Counter 2 */
-	0,	/* Timer Counter 3 */
-	0,	/* Timer Counter 4 */
-	0,	/* Timer Counter 5 */
-	2,	/* USB Host port */
-	3,	/* Ethernet MAC */
-	0,	/* Advanced Interrupt Controller (IRQ0) */
-	0,	/* Advanced Interrupt Controller (IRQ1) */
-	0,	/* Advanced Interrupt Controller (IRQ2) */
-	0,	/* Advanced Interrupt Controller (IRQ3) */
-	0,	/* Advanced Interrupt Controller (IRQ4) */
-	0,	/* Advanced Interrupt Controller (IRQ5) */
-	0	/* Advanced Interrupt Controller (IRQ6) */
-};
-
 AT91_SOC_START(at91rm9200)
 	.map_io = at91rm9200_map_io,
-	.default_irq_priority = at91rm9200_default_irq_priority,
-	.extern_irq = (1 << AT91RM9200_ID_IRQ0) | (1 << AT91RM9200_ID_IRQ1)
-		    | (1 << AT91RM9200_ID_IRQ2) | (1 << AT91RM9200_ID_IRQ3)
-		    | (1 << AT91RM9200_ID_IRQ4) | (1 << AT91RM9200_ID_IRQ5)
-		    | (1 << AT91RM9200_ID_IRQ6),
-	.ioremap_registers = at91rm9200_ioremap_registers,
-	.register_clocks = at91rm9200_register_clocks,
 	.init = at91rm9200_initialize,
 AT91_SOC_END

arch/arm/mach-at91/at91rm9200_devices.c

@@ -1,1212 +0,0 @@
-/*
- * arch/arm/mach-at91/at91rm9200_devices.c
- *
- *  Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
- *  Copyright (C) 2005 David Brownell
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/platform_device.h>
-#include <linux/i2c-gpio.h>
-
-#include <mach/at91rm9200.h>
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-#include <mach/hardware.h>
-
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-/* --------------------------------------------------------------------
- *  USB Host
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-static struct at91_usbh_data usbh_data;
-
-static struct resource usbh_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_UHP_BASE,
-		.end	= AT91RM9200_UHP_BASE + SZ_1M - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_UHP,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_UHP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_usbh_device = {
-	.name		= "at91_ohci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &ohci_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &usbh_data,
-	},
-	.resource	= usbh_resources,
-	.num_resources	= ARRAY_SIZE(usbh_resources),
-};
-
-void __init at91_add_device_usbh(struct at91_usbh_data *data)
-{
-	int i;
-
-	if (!data)
-		return;
-
-	/* Enable overcurrent notification */
-	for (i = 0; i < data->ports; i++) {
-		if (gpio_is_valid(data->overcurrent_pin[i]))
-			at91_set_gpio_input(data->overcurrent_pin[i], 1);
-	}
-
-	usbh_data = *data;
-	platform_device_register(&at91rm9200_usbh_device);
-}
-#else
-void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  USB Device (Gadget)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
-static struct at91_udc_data udc_data;
-
-static struct resource udc_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_UDP,
-		.end	= AT91RM9200_BASE_UDP + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_UDP,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_UDP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_udc_device = {
-	.name		= "at91_udc",
-	.id		= -1,
-	.dev		= {
-				.platform_data		= &udc_data,
-	},
-	.resource	= udc_resources,
-	.num_resources	= ARRAY_SIZE(udc_resources),
-};
-
-void __init at91_add_device_udc(struct at91_udc_data *data)
-{
-	if (!data)
-		return;
-
-	if (gpio_is_valid(data->vbus_pin)) {
-		at91_set_gpio_input(data->vbus_pin, 0);
-		at91_set_deglitch(data->vbus_pin, 1);
-	}
-	if (gpio_is_valid(data->pullup_pin))
-		at91_set_gpio_output(data->pullup_pin, 0);
-
-	udc_data = *data;
-	platform_device_register(&at91rm9200_udc_device);
-}
-#else
-void __init at91_add_device_udc(struct at91_udc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Ethernet
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE)
-static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct macb_platform_data eth_data;
-
-static struct resource eth_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_EMAC,
-		.end	= AT91RM9200_BASE_EMAC + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_EMAC,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_EMAC,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_eth_device = {
-	.name		= "at91_ether",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &eth_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &eth_data,
-	},
-	.resource	= eth_resources,
-	.num_resources	= ARRAY_SIZE(eth_resources),
-};
-
-void __init at91_add_device_eth(struct macb_platform_data *data)
-{
-	if (!data)
-		return;
-
-	if (gpio_is_valid(data->phy_irq_pin)) {
-		at91_set_gpio_input(data->phy_irq_pin, 0);
-		at91_set_deglitch(data->phy_irq_pin, 1);
-	}
-
-	/* Pins used for MII and RMII */
-	at91_set_A_periph(AT91_PIN_PA16, 0);	/* EMDIO */
-	at91_set_A_periph(AT91_PIN_PA15, 0);	/* EMDC */
-	at91_set_A_periph(AT91_PIN_PA14, 0);	/* ERXER */
-	at91_set_A_periph(AT91_PIN_PA13, 0);	/* ERX1 */
-	at91_set_A_periph(AT91_PIN_PA12, 0);	/* ERX0 */
-	at91_set_A_periph(AT91_PIN_PA11, 0);	/* ECRS_ECRSDV */
-	at91_set_A_periph(AT91_PIN_PA10, 0);	/* ETX1 */
-	at91_set_A_periph(AT91_PIN_PA9, 0);	/* ETX0 */
-	at91_set_A_periph(AT91_PIN_PA8, 0);	/* ETXEN */
-	at91_set_A_periph(AT91_PIN_PA7, 0);	/* ETXCK_EREFCK */
-
-	if (!data->is_rmii) {
-		at91_set_B_periph(AT91_PIN_PB19, 0);	/* ERXCK */
-		at91_set_B_periph(AT91_PIN_PB18, 0);	/* ECOL */
-		at91_set_B_periph(AT91_PIN_PB17, 0);	/* ERXDV */
-		at91_set_B_periph(AT91_PIN_PB16, 0);	/* ERX3 */
-		at91_set_B_periph(AT91_PIN_PB15, 0);	/* ERX2 */
-		at91_set_B_periph(AT91_PIN_PB14, 0);	/* ETXER */
-		at91_set_B_periph(AT91_PIN_PB13, 0);	/* ETX3 */
-		at91_set_B_periph(AT91_PIN_PB12, 0);	/* ETX2 */
-	}
-
-	eth_data = *data;
-	platform_device_register(&at91rm9200_eth_device);
-}
-#else
-void __init at91_add_device_eth(struct macb_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Compact Flash / PCMCIA
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
-static struct at91_cf_data cf_data;
-
-#define CF_BASE		AT91_CHIPSELECT_4
-
-static struct resource cf_resources[] = {
-	[0] = {
-		.start	= CF_BASE,
-		/* ties up CS4, CS5 and CS6 */
-		.end	= CF_BASE + (0x30000000 - 1),
-		.flags	= IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
-	},
-};
-
-static struct platform_device at91rm9200_cf_device = {
-	.name		= "at91_cf",
-	.id		= -1,
-	.dev		= {
-				.platform_data		= &cf_data,
-	},
-	.resource	= cf_resources,
-	.num_resources	= ARRAY_SIZE(cf_resources),
-};
-
-void __init at91_add_device_cf(struct at91_cf_data *data)
-{
-	unsigned int csa;
-
-	if (!data)
-		return;
-
-	data->chipselect = 4;		/* can only use EBI ChipSelect 4 */
-
-	/* CF takes over CS4, CS5, CS6 */
-	csa = at91_ramc_read(0, AT91_EBI_CSA);
-	at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH);
-
-	/*
-	 * Static memory controller timing adjustments.
-	 * REVISIT:  these timings are in terms of MCK cycles, so
-	 * when MCK changes (cpufreq etc) so must these values...
-	 */
-	at91_ramc_write(0, AT91_SMC_CSR(4),
-				  AT91_SMC_ACSS_STD
-				| AT91_SMC_DBW_16
-				| AT91_SMC_BAT
-				| AT91_SMC_WSEN
-				| AT91_SMC_NWS_(32)	/* wait states */
-				| AT91_SMC_RWSETUP_(6)	/* setup time */
-				| AT91_SMC_RWHOLD_(4)	/* hold time */
-	);
-
-	/* input/irq */
-	if (gpio_is_valid(data->irq_pin)) {
-		at91_set_gpio_input(data->irq_pin, 1);
-		at91_set_deglitch(data->irq_pin, 1);
-	}
-	at91_set_gpio_input(data->det_pin, 1);
-	at91_set_deglitch(data->det_pin, 1);
-
-	/* outputs, initially off */
-	if (gpio_is_valid(data->vcc_pin))
-		at91_set_gpio_output(data->vcc_pin, 0);
-	at91_set_gpio_output(data->rst_pin, 0);
-
-	/* force poweron defaults for these pins ... */
-	at91_set_A_periph(AT91_PIN_PC9, 0);	/* A25/CFRNW */
-	at91_set_A_periph(AT91_PIN_PC10, 0);	/* NCS4/CFCS */
-	at91_set_A_periph(AT91_PIN_PC11, 0);	/* NCS5/CFCE1 */
-	at91_set_A_periph(AT91_PIN_PC12, 0);	/* NCS6/CFCE2 */
-
-	/* nWAIT is _not_ a default setting */
-	at91_set_A_periph(AT91_PIN_PC6, 1);	/* nWAIT */
-
-	cf_data = *data;
-	platform_device_register(&at91rm9200_cf_device);
-}
-#else
-void __init at91_add_device_cf(struct at91_cf_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  MMC / SD
- * -------------------------------------------------------------------- */
-
-#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct mci_platform_data mmc_data;
-
-static struct resource mmc_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_MCI,
-		.end	= AT91RM9200_BASE_MCI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_MCI,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_MCI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_mmc_device = {
-	.name		= "atmel_mci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &mmc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &mmc_data,
-	},
-	.resource	= mmc_resources,
-	.num_resources	= ARRAY_SIZE(mmc_resources),
-};
-
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
-{
-	unsigned int i;
-	unsigned int slot_count = 0;
-
-	if (!data)
-		return;
-
-	for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
-
-		if (!data->slot[i].bus_width)
-			continue;
-
-		/* input/irq */
-		if (gpio_is_valid(data->slot[i].detect_pin)) {
-			at91_set_gpio_input(data->slot[i].detect_pin, 1);
-			at91_set_deglitch(data->slot[i].detect_pin, 1);
-		}
-		if (gpio_is_valid(data->slot[i].wp_pin))
-			at91_set_gpio_input(data->slot[i].wp_pin, 1);
-
-		switch (i) {
-		case 0:					/* slot A */
-			/* CMD */
-			at91_set_A_periph(AT91_PIN_PA28, 1);
-			/* DAT0, maybe DAT1..DAT3 */
-			at91_set_A_periph(AT91_PIN_PA29, 1);
-			if (data->slot[i].bus_width == 4) {
-				at91_set_B_periph(AT91_PIN_PB3, 1);
-				at91_set_B_periph(AT91_PIN_PB4, 1);
-				at91_set_B_periph(AT91_PIN_PB5, 1);
-			}
-			slot_count++;
-			break;
-		case 1:					/* slot B */
-			/* CMD */
-			at91_set_B_periph(AT91_PIN_PA8, 1);
-			/* DAT0, maybe DAT1..DAT3 */
-			at91_set_B_periph(AT91_PIN_PA9, 1);
-			if (data->slot[i].bus_width == 4) {
-				at91_set_B_periph(AT91_PIN_PA10, 1);
-				at91_set_B_periph(AT91_PIN_PA11, 1);
-				at91_set_B_periph(AT91_PIN_PA12, 1);
-			}
-			slot_count++;
-			break;
-		default:
-			printk(KERN_ERR
-			       "AT91: SD/MMC slot %d not available\n", i);
-			break;
-		}
-		if (slot_count) {
-			/* CLK */
-			at91_set_A_periph(AT91_PIN_PA27, 0);
-
-			mmc_data = *data;
-			platform_device_register(&at91rm9200_mmc_device);
-		}
-	}
-
-}
-#else
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  NAND / SmartMedia
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
-static struct atmel_nand_data nand_data;
-
-#define NAND_BASE	AT91_CHIPSELECT_3
-
-static struct resource nand_resources[] = {
-	{
-		.start	= NAND_BASE,
-		.end	= NAND_BASE + SZ_256M - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device at91rm9200_nand_device = {
-	.name		= "atmel_nand",
-	.id		= -1,
-	.dev		= {
-				.platform_data	= &nand_data,
-	},
-	.resource	= nand_resources,
-	.num_resources	= ARRAY_SIZE(nand_resources),
-};
-
-void __init at91_add_device_nand(struct atmel_nand_data *data)
-{
-	unsigned int csa;
-
-	if (!data)
-		return;
-
-	/* enable the address range of CS3 */
-	csa = at91_ramc_read(0, AT91_EBI_CSA);
-	at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
-
-	/* set the bus interface characteristics */
-	at91_ramc_write(0, AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
-		| AT91_SMC_NWS_(5)
-		| AT91_SMC_TDF_(1)
-		| AT91_SMC_RWSETUP_(0)	/* tDS Data Set up Time 30 - ns */
-		| AT91_SMC_RWHOLD_(1)	/* tDH Data Hold Time 20 - ns */
-	);
-
-	/* enable pin */
-	if (gpio_is_valid(data->enable_pin))
-		at91_set_gpio_output(data->enable_pin, 1);
-
-	/* ready/busy pin */
-	if (gpio_is_valid(data->rdy_pin))
-		at91_set_gpio_input(data->rdy_pin, 1);
-
-	/* card detect pin */
-	if (gpio_is_valid(data->det_pin))
-		at91_set_gpio_input(data->det_pin, 1);
-
-	at91_set_A_periph(AT91_PIN_PC1, 0);		/* SMOE */
-	at91_set_A_periph(AT91_PIN_PC3, 0);		/* SMWE */
-
-	nand_data = *data;
-	platform_device_register(&at91rm9200_nand_device);
-}
-#else
-void __init at91_add_device_nand(struct atmel_nand_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  TWI (i2c)
- * -------------------------------------------------------------------- */
-
-/*
- * Prefer the GPIO code since the TWI controller isn't robust
- * (gets overruns and underruns under load) and can only issue
- * repeated STARTs in one scenario (the driver doesn't yet handle them).
- */
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
-
-static struct i2c_gpio_platform_data pdata = {
-	.sda_pin		= AT91_PIN_PA25,
-	.sda_is_open_drain	= 1,
-	.scl_pin		= AT91_PIN_PA26,
-	.scl_is_open_drain	= 1,
-	.udelay			= 2,		/* ~100 kHz */
-};
-
-static struct platform_device at91rm9200_twi_device = {
-	.name			= "i2c-gpio",
-	.id			= 0,
-	.dev.platform_data	= &pdata,
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	at91_set_GPIO_periph(AT91_PIN_PA25, 1);		/* TWD (SDA) */
-	at91_set_multi_drive(AT91_PIN_PA25, 1);
-
-	at91_set_GPIO_periph(AT91_PIN_PA26, 1);		/* TWCK (SCL) */
-	at91_set_multi_drive(AT91_PIN_PA26, 1);
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at91rm9200_twi_device);
-}
-
-#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
-
-static struct resource twi_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_TWI,
-		.end	= AT91RM9200_BASE_TWI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_TWI,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_TWI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_twi_device = {
-	.name		= "i2c-at91rm9200",
-	.id		= 0,
-	.resource	= twi_resources,
-	.num_resources	= ARRAY_SIZE(twi_resources),
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	/* pins used for TWI interface */
-	at91_set_A_periph(AT91_PIN_PA25, 0);		/* TWD */
-	at91_set_multi_drive(AT91_PIN_PA25, 1);
-
-	at91_set_A_periph(AT91_PIN_PA26, 0);		/* TWCK */
-	at91_set_multi_drive(AT91_PIN_PA26, 1);
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at91rm9200_twi_device);
-}
-#else
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  SPI
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct resource spi_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_SPI,
-		.end	= AT91RM9200_BASE_SPI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_SPI,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_SPI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_spi_device = {
-	.name		= "atmel_spi",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &spi_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= spi_resources,
-	.num_resources	= ARRAY_SIZE(spi_resources),
-};
-
-static const unsigned spi_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
-
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
-{
-	int i;
-	unsigned long cs_pin;
-
-	at91_set_A_periph(AT91_PIN_PA0, 0);	/* MISO */
-	at91_set_A_periph(AT91_PIN_PA1, 0);	/* MOSI */
-	at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPCK */
-
-	/* Enable SPI chip-selects */
-	for (i = 0; i < nr_devices; i++) {
-		if (devices[i].controller_data)
-			cs_pin = (unsigned long) devices[i].controller_data;
-		else
-			cs_pin = spi_standard_cs[devices[i].chip_select];
-
-		if (devices[i].chip_select == 0)	/* for CS0 errata */
-			at91_set_A_periph(cs_pin, 0);
-		else
-			at91_set_gpio_output(cs_pin, 1);
-
-
-		/* pass chip-select pin to driver */
-		devices[i].controller_data = (void *) cs_pin;
-	}
-
-	spi_register_board_info(devices, nr_devices);
-	platform_device_register(&at91rm9200_spi_device);
-}
-#else
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Timer/Counter blocks
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_ATMEL_TCLIB
-
-static struct resource tcb0_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_TCB0,
-		.end	= AT91RM9200_BASE_TCB0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_TC0,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_TC0,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[2] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_TC1,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_TC1,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[3] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_TC2,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_TC2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_tcb0_device = {
-	.name		= "atmel_tcb",
-	.id		= 0,
-	.resource	= tcb0_resources,
-	.num_resources	= ARRAY_SIZE(tcb0_resources),
-};
-
-static struct resource tcb1_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_TCB1,
-		.end	= AT91RM9200_BASE_TCB1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_TC3,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_TC3,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[2] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_TC4,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_TC4,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[3] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_TC5,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_TC5,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_tcb1_device = {
-	.name		= "atmel_tcb",
-	.id		= 1,
-	.resource	= tcb1_resources,
-	.num_resources	= ARRAY_SIZE(tcb1_resources),
-};
-
-static void __init at91_add_device_tc(void)
-{
-	platform_device_register(&at91rm9200_tcb0_device);
-	platform_device_register(&at91rm9200_tcb1_device);
-}
-#else
-static void __init at91_add_device_tc(void) { }
-#endif
-
-
-/* --------------------------------------------------------------------
- *  RTC
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
-static struct resource rtc_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_RTC,
-		.end	= AT91RM9200_BASE_RTC + SZ_256 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.end	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_rtc_device = {
-	.name		= "at91_rtc",
-	.id		= -1,
-	.resource	= rtc_resources,
-	.num_resources	= ARRAY_SIZE(rtc_resources),
-};
-
-static void __init at91_add_device_rtc(void)
-{
-	platform_device_register(&at91rm9200_rtc_device);
-}
-#else
-static void __init at91_add_device_rtc(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Watchdog
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91RM9200_WATCHDOG) || defined(CONFIG_AT91RM9200_WATCHDOG_MODULE)
-static struct platform_device at91rm9200_wdt_device = {
-	.name		= "at91_wdt",
-	.id		= -1,
-	.num_resources	= 0,
-};
-
-static void __init at91_add_device_watchdog(void)
-{
-	platform_device_register(&at91rm9200_wdt_device);
-}
-#else
-static void __init at91_add_device_watchdog(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  SSC -- Synchronous Serial Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
-static u64 ssc0_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc0_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_SSC0,
-		.end	= AT91RM9200_BASE_SSC0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_SSC0,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_SSC0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_ssc0_device = {
-	.name	= "at91rm9200_ssc",
-	.id	= 0,
-	.dev	= {
-		.dma_mask		= &ssc0_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= ssc0_resources,
-	.num_resources	= ARRAY_SIZE(ssc0_resources),
-};
-
-static inline void configure_ssc0_pins(unsigned pins)
-{
-	if (pins & ATMEL_SSC_TF)
-		at91_set_A_periph(AT91_PIN_PB0, 1);
-	if (pins & ATMEL_SSC_TK)
-		at91_set_A_periph(AT91_PIN_PB1, 1);
-	if (pins & ATMEL_SSC_TD)
-		at91_set_A_periph(AT91_PIN_PB2, 1);
-	if (pins & ATMEL_SSC_RD)
-		at91_set_A_periph(AT91_PIN_PB3, 1);
-	if (pins & ATMEL_SSC_RK)
-		at91_set_A_periph(AT91_PIN_PB4, 1);
-	if (pins & ATMEL_SSC_RF)
-		at91_set_A_periph(AT91_PIN_PB5, 1);
-}
-
-static u64 ssc1_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc1_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_SSC1,
-		.end	= AT91RM9200_BASE_SSC1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_SSC1,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_SSC1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_ssc1_device = {
-	.name	= "at91rm9200_ssc",
-	.id	= 1,
-	.dev	= {
-		.dma_mask		= &ssc1_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= ssc1_resources,
-	.num_resources	= ARRAY_SIZE(ssc1_resources),
-};
-
-static inline void configure_ssc1_pins(unsigned pins)
-{
-	if (pins & ATMEL_SSC_TF)
-		at91_set_A_periph(AT91_PIN_PB6, 1);
-	if (pins & ATMEL_SSC_TK)
-		at91_set_A_periph(AT91_PIN_PB7, 1);
-	if (pins & ATMEL_SSC_TD)
-		at91_set_A_periph(AT91_PIN_PB8, 1);
-	if (pins & ATMEL_SSC_RD)
-		at91_set_A_periph(AT91_PIN_PB9, 1);
-	if (pins & ATMEL_SSC_RK)
-		at91_set_A_periph(AT91_PIN_PB10, 1);
-	if (pins & ATMEL_SSC_RF)
-		at91_set_A_periph(AT91_PIN_PB11, 1);
-}
-
-static u64 ssc2_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc2_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_SSC2,
-		.end	= AT91RM9200_BASE_SSC2 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_SSC2,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_SSC2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91rm9200_ssc2_device = {
-	.name	= "at91rm9200_ssc",
-	.id	= 2,
-	.dev	= {
-		.dma_mask		= &ssc2_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= ssc2_resources,
-	.num_resources	= ARRAY_SIZE(ssc2_resources),
-};
-
-static inline void configure_ssc2_pins(unsigned pins)
-{
-	if (pins & ATMEL_SSC_TF)
-		at91_set_A_periph(AT91_PIN_PB12, 1);
-	if (pins & ATMEL_SSC_TK)
-		at91_set_A_periph(AT91_PIN_PB13, 1);
-	if (pins & ATMEL_SSC_TD)
-		at91_set_A_periph(AT91_PIN_PB14, 1);
-	if (pins & ATMEL_SSC_RD)
-		at91_set_A_periph(AT91_PIN_PB15, 1);
-	if (pins & ATMEL_SSC_RK)
-		at91_set_A_periph(AT91_PIN_PB16, 1);
-	if (pins & ATMEL_SSC_RF)
-		at91_set_A_periph(AT91_PIN_PB17, 1);
-}
-
-/*
- * SSC controllers are accessed through library code, instead of any
- * kind of all-singing/all-dancing driver.  For example one could be
- * used by a particular I2S audio codec's driver, while another one
- * on the same system might be used by a custom data capture driver.
- */
-void __init at91_add_device_ssc(unsigned id, unsigned pins)
-{
-	struct platform_device *pdev;
-
-	/*
-	 * NOTE: caller is responsible for passing information matching
-	 * "pins" to whatever will be using each particular controller.
-	 */
-	switch (id) {
-	case AT91RM9200_ID_SSC0:
-		pdev = &at91rm9200_ssc0_device;
-		configure_ssc0_pins(pins);
-		break;
-	case AT91RM9200_ID_SSC1:
-		pdev = &at91rm9200_ssc1_device;
-		configure_ssc1_pins(pins);
-		break;
-	case AT91RM9200_ID_SSC2:
-		pdev = &at91rm9200_ssc2_device;
-		configure_ssc2_pins(pins);
-		break;
-	default:
-		return;
-	}
-
-	platform_device_register(pdev);
-}
-
-#else
-void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  UART
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SERIAL_ATMEL)
-static struct resource dbgu_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_DBGU,
-		.end	= AT91RM9200_BASE_DBGU + SZ_512 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.end	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data dbgu_data = {
-	.use_dma_tx	= 0,
-	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
-};
-
-static u64 dbgu_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_dbgu_device = {
-	.name		= "atmel_usart",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &dbgu_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &dbgu_data,
-	},
-	.resource	= dbgu_resources,
-	.num_resources	= ARRAY_SIZE(dbgu_resources),
-};
-
-static inline void configure_dbgu_pins(void)
-{
-	at91_set_A_periph(AT91_PIN_PA30, 0);		/* DRXD */
-	at91_set_A_periph(AT91_PIN_PA31, 1);		/* DTXD */
-}
-
-static struct resource uart0_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_US0,
-		.end	= AT91RM9200_BASE_US0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_US0,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_US0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart0_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static struct gpiod_lookup_table uart0_gpios_table = {
-	.dev_id = "atmel_usart",
-	.table = {
-		GPIO_LOOKUP("pioA", 21, "rts", GPIO_ACTIVE_LOW),
-		{ },
-	},
-};
-
-static u64 uart0_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_uart0_device = {
-	.name		= "atmel_usart",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &uart0_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart0_data,
-	},
-	.resource	= uart0_resources,
-	.num_resources	= ARRAY_SIZE(uart0_resources),
-};
-
-static inline void configure_usart0_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PA17, 1);		/* TXD0 */
-	at91_set_A_periph(AT91_PIN_PA18, 0);		/* RXD0 */
-
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PA20, 0);	/* CTS0 */
-
-	if (pins & ATMEL_UART_RTS) {
-		/*
-		 * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
-		 * We need to drive the pin manually. The serial driver will driver
-		 * this to high when initializing.
-		 */
-		gpiod_add_lookup_table(&uart0_gpios_table);
-	}
-}
-
-static struct resource uart1_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_US1,
-		.end	= AT91RM9200_BASE_US1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_US1,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_US1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart1_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart1_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_uart1_device = {
-	.name		= "atmel_usart",
-	.id		= 2,
-	.dev		= {
-				.dma_mask		= &uart1_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart1_data,
-	},
-	.resource	= uart1_resources,
-	.num_resources	= ARRAY_SIZE(uart1_resources),
-};
-
-static inline void configure_usart1_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PB20, 1);		/* TXD1 */
-	at91_set_A_periph(AT91_PIN_PB21, 0);		/* RXD1 */
-
-	if (pins & ATMEL_UART_RI)
-		at91_set_A_periph(AT91_PIN_PB18, 0);	/* RI1 */
-	if (pins & ATMEL_UART_DTR)
-		at91_set_A_periph(AT91_PIN_PB19, 0);	/* DTR1 */
-	if (pins & ATMEL_UART_DCD)
-		at91_set_A_periph(AT91_PIN_PB23, 0);	/* DCD1 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PB24, 0);	/* CTS1 */
-	if (pins & ATMEL_UART_DSR)
-		at91_set_A_periph(AT91_PIN_PB25, 0);	/* DSR1 */
-	if (pins & ATMEL_UART_RTS)
-		at91_set_A_periph(AT91_PIN_PB26, 0);	/* RTS1 */
-}
-
-static struct resource uart2_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_US2,
-		.end	= AT91RM9200_BASE_US2 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_US2,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_US2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart2_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart2_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_uart2_device = {
-	.name		= "atmel_usart",
-	.id		= 3,
-	.dev		= {
-				.dma_mask		= &uart2_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart2_data,
-	},
-	.resource	= uart2_resources,
-	.num_resources	= ARRAY_SIZE(uart2_resources),
-};
-
-static inline void configure_usart2_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PA22, 0);		/* RXD2 */
-	at91_set_A_periph(AT91_PIN_PA23, 1);		/* TXD2 */
-
-	if (pins & ATMEL_UART_CTS)
-		at91_set_B_periph(AT91_PIN_PA30, 0);	/* CTS2 */
-	if (pins & ATMEL_UART_RTS)
-		at91_set_B_periph(AT91_PIN_PA31, 0);	/* RTS2 */
-}
-
-static struct resource uart3_resources[] = {
-	[0] = {
-		.start	= AT91RM9200_BASE_US3,
-		.end	= AT91RM9200_BASE_US3 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91RM9200_ID_US3,
-		.end	= NR_IRQS_LEGACY + AT91RM9200_ID_US3,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart3_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart3_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_uart3_device = {
-	.name		= "atmel_usart",
-	.id		= 4,
-	.dev		= {
-				.dma_mask		= &uart3_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart3_data,
-	},
-	.resource	= uart3_resources,
-	.num_resources	= ARRAY_SIZE(uart3_resources),
-};
-
-static inline void configure_usart3_pins(unsigned pins)
-{
-	at91_set_B_periph(AT91_PIN_PA5, 1);		/* TXD3 */
-	at91_set_B_periph(AT91_PIN_PA6, 0);		/* RXD3 */
-
-	if (pins & ATMEL_UART_CTS)
-		at91_set_B_periph(AT91_PIN_PB1, 0);	/* CTS3 */
-	if (pins & ATMEL_UART_RTS)
-		at91_set_B_periph(AT91_PIN_PB0, 0);	/* RTS3 */
-}
-
-static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
-
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
-{
-	struct platform_device *pdev;
-	struct atmel_uart_data *pdata;
-
-	switch (id) {
-		case 0:		/* DBGU */
-			pdev = &at91rm9200_dbgu_device;
-			configure_dbgu_pins();
-			break;
-		case AT91RM9200_ID_US0:
-			pdev = &at91rm9200_uart0_device;
-			configure_usart0_pins(pins);
-			break;
-		case AT91RM9200_ID_US1:
-			pdev = &at91rm9200_uart1_device;
-			configure_usart1_pins(pins);
-			break;
-		case AT91RM9200_ID_US2:
-			pdev = &at91rm9200_uart2_device;
-			configure_usart2_pins(pins);
-			break;
-		case AT91RM9200_ID_US3:
-			pdev = &at91rm9200_uart3_device;
-			configure_usart3_pins(pins);
-			break;
-		default:
-			return;
-	}
-	pdata = pdev->dev.platform_data;
-	pdata->num = portnr;		/* update to mapped ID */
-
-	if (portnr < ATMEL_MAX_UART)
-		at91_uarts[portnr] = pdev;
-}
-
-void __init at91_add_device_serial(void)
-{
-	int i;
-
-	for (i = 0; i < ATMEL_MAX_UART; i++) {
-		if (at91_uarts[i])
-			platform_device_register(at91_uarts[i]);
-	}
-}
-#else
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_add_device_serial(void) {}
-#endif
-
-
-/* -------------------------------------------------------------------- */
-
-/*
- * These devices are always present and don't need any board-specific
- * setup.
- */
-static int __init at91_add_standard_devices(void)
-{
-	at91_add_device_rtc();
-	at91_add_device_watchdog();
-	at91_add_device_tc();
-	return 0;
-}
-
-arch_initcall(at91_add_standard_devices);

arch/arm/mach-at91/at91rm9200_time.c

@@ -183,7 +183,6 @@ static struct clock_event_device clkevt = {
 void __iomem *at91_st_base;
 EXPORT_SYMBOL_GPL(at91_st_base);
 
-#ifdef CONFIG_OF
 static struct of_device_id at91rm9200_st_timer_ids[] = {
 	{ .compatible = "atmel,at91rm9200-st" },
 	{ /* sentinel */ }
@@ -219,28 +218,6 @@ node_err:
 err:
 	return -EINVAL;
 }
-#else
-static int __init of_at91rm9200_st_init(void)
-{
-	return -EINVAL;
-}
-#endif
-
-void __init at91rm9200_ioremap_st(u32 addr)
-{
-#ifdef CONFIG_OF
-	struct device_node *np;
-
-	np = of_find_matching_node(NULL, at91rm9200_st_timer_ids);
-	if (np) {
-		of_node_put(np);
-		return;
-	}
-#endif
-	at91_st_base = ioremap(addr, 256);
-	if (!at91_st_base)
-		panic("Impossible to ioremap ST\n");
-}
 
 /*
  * ST (system timer) module supports both clockevents and clocksource.

arch/arm/mach-at91/at91sam9260.c

@@ -10,307 +10,13 @@
  *
  */
 
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk/at91_pmc.h>
-
-#include <asm/proc-fns.h>
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
 #include <asm/system_misc.h>
 #include <mach/cpu.h>
 #include <mach/at91_dbgu.h>
-#include <mach/at91sam9260.h>
 #include <mach/hardware.h>
 
-#include "at91_aic.h"
 #include "soc.h"
 #include "generic.h"
-#include "sam9_smc.h"
-#include "pm.h"
-
-#if defined(CONFIG_OLD_CLK_AT91)
-#include "clock.h"
-/* --------------------------------------------------------------------
- *  Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk pioA_clk = {
-	.name		= "pioA_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_PIOA,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioB_clk = {
-	.name		= "pioB_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_PIOB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioC_clk = {
-	.name		= "pioC_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_PIOC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk adc_clk = {
-	.name		= "adc_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_ADC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk adc_op_clk = {
-	.name		= "adc_op_clk",
-	.type		= CLK_TYPE_PERIPHERAL,
-	.rate_hz	= 5000000,
-};
-
-static struct clk usart0_clk = {
-	.name		= "usart0_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_US0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
-	.name		= "usart1_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_US1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
-	.name		= "usart2_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_US2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc_clk = {
-	.name		= "mci_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_MCI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk udc_clk = {
-	.name		= "udc_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_UDP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi_clk = {
-	.name		= "twi_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_TWI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi0_clk = {
-	.name		= "spi0_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_SPI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi1_clk = {
-	.name		= "spi1_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_SPI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc_clk = {
-	.name		= "ssc_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_SSC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc0_clk = {
-	.name		= "tc0_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_TC0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc1_clk = {
-	.name		= "tc1_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_TC1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc2_clk = {
-	.name		= "tc2_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_TC2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ohci_clk = {
-	.name		= "ohci_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_UHP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk macb_clk = {
-	.name		= "pclk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_EMAC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk isi_clk = {
-	.name		= "isi_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_ISI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart3_clk = {
-	.name		= "usart3_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_US3,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart4_clk = {
-	.name		= "usart4_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_US4,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart5_clk = {
-	.name		= "usart5_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_US5,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc3_clk = {
-	.name		= "tc3_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_TC3,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc4_clk = {
-	.name		= "tc4_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_TC4,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc5_clk = {
-	.name		= "tc5_clk",
-	.pmc_mask	= 1 << AT91SAM9260_ID_TC5,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk *periph_clocks[] __initdata = {
-	&pioA_clk,
-	&pioB_clk,
-	&pioC_clk,
-	&adc_clk,
-	&adc_op_clk,
-	&usart0_clk,
-	&usart1_clk,
-	&usart2_clk,
-	&mmc_clk,
-	&udc_clk,
-	&twi_clk,
-	&spi0_clk,
-	&spi1_clk,
-	&ssc_clk,
-	&tc0_clk,
-	&tc1_clk,
-	&tc2_clk,
-	&ohci_clk,
-	&macb_clk,
-	&isi_clk,
-	&usart3_clk,
-	&usart4_clk,
-	&usart5_clk,
-	&tc3_clk,
-	&tc4_clk,
-	&tc5_clk,
-	// irq0 .. irq2
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
-	/* One additional fake clock for macb_hclk */
-	CLKDEV_CON_ID("hclk", &macb_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.1", &tc3_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.1", &tc4_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.1", &tc5_clk),
-	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.0", &ssc_clk),
-	CLKDEV_CON_DEV_ID("pclk", "fffbc000.ssc", &ssc_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260.0", &twi_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g20.0", &twi_clk),
-	CLKDEV_CON_DEV_ID(NULL, "rtc-at91sam9.0", &clk32k),
-	/* more usart lookup table for DT entries */
-	CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
-	CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "fffb4000.serial", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "fffb8000.serial", &usart2_clk),
-	CLKDEV_CON_DEV_ID("usart", "fffd0000.serial", &usart3_clk),
-	CLKDEV_CON_DEV_ID("usart", "fffd4000.serial", &usart4_clk),
-	CLKDEV_CON_DEV_ID("usart", "fffd8000.serial", &usart5_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffac000.i2c", &twi_clk),
-	/* more tc lookup table for DT entries */
-	CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "fffa0000.timer", &tc1_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "fffa0000.timer", &tc2_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "fffdc000.timer", &tc3_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "fffdc000.timer", &tc4_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "fffdc000.timer", &tc5_clk),
-	CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &ohci_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "fffa8000.mmc", &mmc_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "fffc8000.spi", &spi0_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "fffcc000.spi", &spi1_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffffd20.rtc", &clk32k),
-	/* fake hclk clock */
-	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
-	CLKDEV_CON_ID("pioA", &pioA_clk),
-	CLKDEV_CON_ID("pioB", &pioB_clk),
-	CLKDEV_CON_ID("pioC", &pioC_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
-};
-
-static struct clk_lookup usart_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.4", &usart3_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.5", &usart4_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.6", &usart5_clk),
-};
-
-/*
- * The two programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
-	.name		= "pck0",
-	.pmc_mask	= AT91_PMC_PCK0,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 0,
-};
-static struct clk pck1 = {
-	.name		= "pck1",
-	.pmc_mask	= AT91_PMC_PCK1,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 1,
-};
-
-static void __init at91sam9260_register_clocks(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
-		clk_register(periph_clocks[i]);
-
-	clkdev_add_table(periph_clocks_lookups,
-			 ARRAY_SIZE(periph_clocks_lookups));
-	clkdev_add_table(usart_clocks_lookups,
-			 ARRAY_SIZE(usart_clocks_lookups));
-
-	clk_register(&pck0);
-	clk_register(&pck1);
-}
-#else
-#define at91sam9260_register_clocks NULL
-#endif
-
-/* --------------------------------------------------------------------
- *  GPIO
- * -------------------------------------------------------------------- */
-
-static struct at91_gpio_bank at91sam9260_gpio[] __initdata = {
-	{
-		.id		= AT91SAM9260_ID_PIOA,
-		.regbase	= AT91SAM9260_BASE_PIOA,
-	}, {
-		.id		= AT91SAM9260_ID_PIOB,
-		.regbase	= AT91SAM9260_BASE_PIOB,
-	}, {
-		.id		= AT91SAM9260_ID_PIOC,
-		.regbase	= AT91SAM9260_BASE_PIOC,
-	}
-};
 
 /* --------------------------------------------------------------------
  *  AT91SAM9260 processor initialization
@@ -342,119 +48,14 @@ static void __init at91sam9260_map_io(void)
 		at91_init_sram(0, AT91SAM9260_SRAM_BASE, AT91SAM9260_SRAM_SIZE);
 }
 
-static void __init at91sam9260_ioremap_registers(void)
-{
-	at91_ioremap_ramc(0, AT91SAM9260_BASE_SDRAMC, 512);
-	at91sam926x_ioremap_pit(AT91SAM9260_BASE_PIT);
-	at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC);
-	at91_ioremap_matrix(AT91SAM9260_BASE_MATRIX);
-	at91_pm_set_standby(at91sam9_sdram_standby);
-}
-
 static void __init at91sam9260_initialize(void)
 {
 	arm_pm_idle = at91sam9_idle;
 
 	at91_sysirq_mask_rtt(AT91SAM9260_BASE_RTT);
-
-	/* Register GPIO subsystem */
-	at91_gpio_init(at91sam9260_gpio, 3);
-}
-
-static struct resource rstc_resources[] = {
-	[0] = {
-		.start  = AT91SAM9260_BASE_RSTC,
-		.end    = AT91SAM9260_BASE_RSTC + SZ_16 - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start  = AT91SAM9260_BASE_SDRAMC,
-		.end    = AT91SAM9260_BASE_SDRAMC + SZ_512 - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device rstc_device = {
-	.name           = "at91-sam9260-reset",
-	.resource       = rstc_resources,
-	.num_resources  = ARRAY_SIZE(rstc_resources),
-};
-
-static struct resource shdwc_resources[] = {
-	[0] = {
-		.start  = AT91SAM9260_BASE_SHDWC,
-		.end    = AT91SAM9260_BASE_SHDWC + SZ_16 - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device shdwc_device = {
-	.name           = "at91-poweroff",
-	.resource       = shdwc_resources,
-	.num_resources  = ARRAY_SIZE(shdwc_resources),
-};
-
-static void __init at91sam9260_register_devices(void)
-{
-	platform_device_register(&rstc_device);
-	platform_device_register(&shdwc_device);
-}
-
-/* --------------------------------------------------------------------
- *  Interrupt initialization
- * -------------------------------------------------------------------- */
-
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = {
-	7,	/* Advanced Interrupt Controller */
-	7,	/* System Peripherals */
-	1,	/* Parallel IO Controller A */
-	1,	/* Parallel IO Controller B */
-	1,	/* Parallel IO Controller C */
-	0,	/* Analog-to-Digital Converter */
-	5,	/* USART 0 */
-	5,	/* USART 1 */
-	5,	/* USART 2 */
-	0,	/* Multimedia Card Interface */
-	2,	/* USB Device Port */
-	6,	/* Two-Wire Interface */
-	5,	/* Serial Peripheral Interface 0 */
-	5,	/* Serial Peripheral Interface 1 */
-	5,	/* Serial Synchronous Controller */
-	0,
-	0,
-	0,	/* Timer Counter 0 */
-	0,	/* Timer Counter 1 */
-	0,	/* Timer Counter 2 */
-	2,	/* USB Host port */
-	3,	/* Ethernet */
-	0,	/* Image Sensor Interface */
-	5,	/* USART 3 */
-	5,	/* USART 4 */
-	5,	/* USART 5 */
-	0,	/* Timer Counter 3 */
-	0,	/* Timer Counter 4 */
-	0,	/* Timer Counter 5 */
-	0,	/* Advanced Interrupt Controller */
-	0,	/* Advanced Interrupt Controller */
-	0,	/* Advanced Interrupt Controller */
-};
-
-static void __init at91sam9260_init_time(void)
-{
-	at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
 }
 
 AT91_SOC_START(at91sam9260)
 	.map_io = at91sam9260_map_io,
-	.default_irq_priority = at91sam9260_default_irq_priority,
-	.extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1)
-		    | (1 << AT91SAM9260_ID_IRQ2),
-	.ioremap_registers = at91sam9260_ioremap_registers,
-	.register_clocks = at91sam9260_register_clocks,
-	.register_devices = at91sam9260_register_devices,
 	.init = at91sam9260_initialize,
-	.init_time = at91sam9260_init_time,
 AT91_SOC_END

arch/arm/mach-at91/at91sam9260_devices.c

@@ -1,1364 +0,0 @@
-/*
- * arch/arm/mach-at91/at91sam9260_devices.c
- *
- *  Copyright (C) 2006 Atmel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/i2c-gpio.h>
-
-#include <linux/platform_data/at91_adc.h>
-
-#include <mach/cpu.h>
-#include <mach/at91sam9260.h>
-#include <mach/at91sam9260_matrix.h>
-#include <mach/at91_matrix.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/hardware.h>
-
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-/* --------------------------------------------------------------------
- *  USB Host
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-static struct at91_usbh_data usbh_data;
-
-static struct resource usbh_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_UHP_BASE,
-		.end	= AT91SAM9260_UHP_BASE + SZ_1M - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_UHP,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_UHP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91_usbh_device = {
-	.name		= "at91_ohci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &ohci_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &usbh_data,
-	},
-	.resource	= usbh_resources,
-	.num_resources	= ARRAY_SIZE(usbh_resources),
-};
-
-void __init at91_add_device_usbh(struct at91_usbh_data *data)
-{
-	int i;
-
-	if (!data)
-		return;
-
-	/* Enable overcurrent notification */
-	for (i = 0; i < data->ports; i++) {
-		if (gpio_is_valid(data->overcurrent_pin[i]))
-			at91_set_gpio_input(data->overcurrent_pin[i], 1);
-	}
-
-	usbh_data = *data;
-	platform_device_register(&at91_usbh_device);
-}
-#else
-void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  USB Device (Gadget)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
-static struct at91_udc_data udc_data;
-
-static struct resource udc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_UDP,
-		.end	= AT91SAM9260_BASE_UDP + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_UDP,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_UDP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91_udc_device = {
-	.name		= "at91_udc",
-	.id		= -1,
-	.dev		= {
-				.platform_data		= &udc_data,
-	},
-	.resource	= udc_resources,
-	.num_resources	= ARRAY_SIZE(udc_resources),
-};
-
-void __init at91_add_device_udc(struct at91_udc_data *data)
-{
-	if (!data)
-		return;
-
-	if (gpio_is_valid(data->vbus_pin)) {
-		at91_set_gpio_input(data->vbus_pin, 0);
-		at91_set_deglitch(data->vbus_pin, 1);
-	}
-
-	/* Pullup pin is handled internally by USB device peripheral */
-
-	udc_data = *data;
-	platform_device_register(&at91_udc_device);
-}
-#else
-void __init at91_add_device_udc(struct at91_udc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Ethernet
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
-static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct macb_platform_data eth_data;
-
-static struct resource eth_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_EMAC,
-		.end	= AT91SAM9260_BASE_EMAC + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_EMAC,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_EMAC,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_eth_device = {
-	.name		= "macb",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &eth_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &eth_data,
-	},
-	.resource	= eth_resources,
-	.num_resources	= ARRAY_SIZE(eth_resources),
-};
-
-void __init at91_add_device_eth(struct macb_platform_data *data)
-{
-	if (!data)
-		return;
-
-	if (gpio_is_valid(data->phy_irq_pin)) {
-		at91_set_gpio_input(data->phy_irq_pin, 0);
-		at91_set_deglitch(data->phy_irq_pin, 1);
-	}
-
-	/* Pins used for MII and RMII */
-	at91_set_A_periph(AT91_PIN_PA19, 0);	/* ETXCK_EREFCK */
-	at91_set_A_periph(AT91_PIN_PA17, 0);	/* ERXDV */
-	at91_set_A_periph(AT91_PIN_PA14, 0);	/* ERX0 */
-	at91_set_A_periph(AT91_PIN_PA15, 0);	/* ERX1 */
-	at91_set_A_periph(AT91_PIN_PA18, 0);	/* ERXER */
-	at91_set_A_periph(AT91_PIN_PA16, 0);	/* ETXEN */
-	at91_set_A_periph(AT91_PIN_PA12, 0);	/* ETX0 */
-	at91_set_A_periph(AT91_PIN_PA13, 0);	/* ETX1 */
-	at91_set_A_periph(AT91_PIN_PA21, 0);	/* EMDIO */
-	at91_set_A_periph(AT91_PIN_PA20, 0);	/* EMDC */
-
-	if (!data->is_rmii) {
-		at91_set_B_periph(AT91_PIN_PA28, 0);	/* ECRS */
-		at91_set_B_periph(AT91_PIN_PA29, 0);	/* ECOL */
-		at91_set_B_periph(AT91_PIN_PA25, 0);	/* ERX2 */
-		at91_set_B_periph(AT91_PIN_PA26, 0);	/* ERX3 */
-		at91_set_B_periph(AT91_PIN_PA27, 0);	/* ERXCK */
-		at91_set_B_periph(AT91_PIN_PA23, 0);	/* ETX2 */
-		at91_set_B_periph(AT91_PIN_PA24, 0);	/* ETX3 */
-		at91_set_B_periph(AT91_PIN_PA22, 0);	/* ETXER */
-	}
-
-	eth_data = *data;
-	platform_device_register(&at91sam9260_eth_device);
-}
-#else
-void __init at91_add_device_eth(struct macb_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  MMC / SD Slot for Atmel MCI Driver
- * -------------------------------------------------------------------- */
-
-#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct mci_platform_data mmc_data;
-
-static struct resource mmc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_MCI,
-		.end	= AT91SAM9260_BASE_MCI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_MCI,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_MCI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_mmc_device = {
-	.name		= "atmel_mci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &mmc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &mmc_data,
-	},
-	.resource	= mmc_resources,
-	.num_resources	= ARRAY_SIZE(mmc_resources),
-};
-
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
-{
-	unsigned int i;
-	unsigned int slot_count = 0;
-
-	if (!data)
-		return;
-
-	for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
-		if (data->slot[i].bus_width) {
-			/* input/irq */
-			if (gpio_is_valid(data->slot[i].detect_pin)) {
-				at91_set_gpio_input(data->slot[i].detect_pin, 1);
-				at91_set_deglitch(data->slot[i].detect_pin, 1);
-			}
-			if (gpio_is_valid(data->slot[i].wp_pin))
-				at91_set_gpio_input(data->slot[i].wp_pin, 1);
-
-			switch (i) {
-			case 0:
-				/* CMD */
-				at91_set_A_periph(AT91_PIN_PA7, 1);
-				/* DAT0, maybe DAT1..DAT3 */
-				at91_set_A_periph(AT91_PIN_PA6, 1);
-				if (data->slot[i].bus_width == 4) {
-					at91_set_A_periph(AT91_PIN_PA9, 1);
-					at91_set_A_periph(AT91_PIN_PA10, 1);
-					at91_set_A_periph(AT91_PIN_PA11, 1);
-				}
-				slot_count++;
-				break;
-			case 1:
-				/* CMD */
-				at91_set_B_periph(AT91_PIN_PA1, 1);
-				/* DAT0, maybe DAT1..DAT3 */
-				at91_set_B_periph(AT91_PIN_PA0, 1);
-				if (data->slot[i].bus_width == 4) {
-					at91_set_B_periph(AT91_PIN_PA5, 1);
-					at91_set_B_periph(AT91_PIN_PA4, 1);
-					at91_set_B_periph(AT91_PIN_PA3, 1);
-				}
-				slot_count++;
-				break;
-			default:
-				printk(KERN_ERR
-					"AT91: SD/MMC slot %d not available\n", i);
-				break;
-			}
-		}
-	}
-
-	if (slot_count) {
-		/* CLK */
-		at91_set_A_periph(AT91_PIN_PA8, 0);
-
-		mmc_data = *data;
-		platform_device_register(&at91sam9260_mmc_device);
-	}
-}
-#else
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  NAND / SmartMedia
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
-static struct atmel_nand_data nand_data;
-
-#define NAND_BASE	AT91_CHIPSELECT_3
-
-static struct resource nand_resources[] = {
-	[0] = {
-		.start	= NAND_BASE,
-		.end	= NAND_BASE + SZ_256M - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT91SAM9260_BASE_ECC,
-		.end	= AT91SAM9260_BASE_ECC + SZ_512 - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device at91sam9260_nand_device = {
-	.name		= "atmel_nand",
-	.id		= -1,
-	.dev		= {
-				.platform_data	= &nand_data,
-	},
-	.resource	= nand_resources,
-	.num_resources	= ARRAY_SIZE(nand_resources),
-};
-
-void __init at91_add_device_nand(struct atmel_nand_data *data)
-{
-	unsigned long csa;
-
-	if (!data)
-		return;
-
-	csa = at91_matrix_read(AT91_MATRIX_EBICSA);
-	at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
-
-	/* enable pin */
-	if (gpio_is_valid(data->enable_pin))
-		at91_set_gpio_output(data->enable_pin, 1);
-
-	/* ready/busy pin */
-	if (gpio_is_valid(data->rdy_pin))
-		at91_set_gpio_input(data->rdy_pin, 1);
-
-	/* card detect pin */
-	if (gpio_is_valid(data->det_pin))
-		at91_set_gpio_input(data->det_pin, 1);
-
-	nand_data = *data;
-	platform_device_register(&at91sam9260_nand_device);
-}
-#else
-void __init at91_add_device_nand(struct atmel_nand_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  TWI (i2c)
- * -------------------------------------------------------------------- */
-
-/*
- * Prefer the GPIO code since the TWI controller isn't robust
- * (gets overruns and underruns under load) and can only issue
- * repeated STARTs in one scenario (the driver doesn't yet handle them).
- */
-
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
-
-static struct i2c_gpio_platform_data pdata = {
-	.sda_pin		= AT91_PIN_PA23,
-	.sda_is_open_drain	= 1,
-	.scl_pin		= AT91_PIN_PA24,
-	.scl_is_open_drain	= 1,
-	.udelay			= 2,		/* ~100 kHz */
-};
-
-static struct platform_device at91sam9260_twi_device = {
-	.name			= "i2c-gpio",
-	.id			= 0,
-	.dev.platform_data	= &pdata,
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	at91_set_GPIO_periph(AT91_PIN_PA23, 1);		/* TWD (SDA) */
-	at91_set_multi_drive(AT91_PIN_PA23, 1);
-
-	at91_set_GPIO_periph(AT91_PIN_PA24, 1);		/* TWCK (SCL) */
-	at91_set_multi_drive(AT91_PIN_PA24, 1);
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at91sam9260_twi_device);
-}
-
-#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
-
-static struct resource twi_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_TWI,
-		.end	= AT91SAM9260_BASE_TWI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_TWI,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_TWI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_twi_device = {
-	.id		= 0,
-	.resource	= twi_resources,
-	.num_resources	= ARRAY_SIZE(twi_resources),
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	/* IP version is not the same on 9260 and g20 */
-	if (cpu_is_at91sam9g20()) {
-		at91sam9260_twi_device.name = "i2c-at91sam9g20";
-	} else {
-		at91sam9260_twi_device.name = "i2c-at91sam9260";
-	}
-
-	/* pins used for TWI interface */
-	at91_set_A_periph(AT91_PIN_PA23, 0);		/* TWD */
-	at91_set_multi_drive(AT91_PIN_PA23, 1);
-
-	at91_set_A_periph(AT91_PIN_PA24, 0);		/* TWCK */
-	at91_set_multi_drive(AT91_PIN_PA24, 1);
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at91sam9260_twi_device);
-}
-#else
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  SPI
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct resource spi0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_SPI0,
-		.end	= AT91SAM9260_BASE_SPI0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_SPI0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_SPI0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_spi0_device = {
-	.name		= "atmel_spi",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &spi_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= spi0_resources,
-	.num_resources	= ARRAY_SIZE(spi0_resources),
-};
-
-static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PC11, AT91_PIN_PC16, AT91_PIN_PC17 };
-
-static struct resource spi1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_SPI1,
-		.end	= AT91SAM9260_BASE_SPI1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_SPI1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_SPI1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_spi1_device = {
-	.name		= "atmel_spi",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &spi_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= spi1_resources,
-	.num_resources	= ARRAY_SIZE(spi1_resources),
-};
-
-static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB3, AT91_PIN_PC5, AT91_PIN_PC4, AT91_PIN_PC3 };
-
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
-{
-	int i;
-	unsigned long cs_pin;
-	short enable_spi0 = 0;
-	short enable_spi1 = 0;
-
-	/* Choose SPI chip-selects */
-	for (i = 0; i < nr_devices; i++) {
-		if (devices[i].controller_data)
-			cs_pin = (unsigned long) devices[i].controller_data;
-		else if (devices[i].bus_num == 0)
-			cs_pin = spi0_standard_cs[devices[i].chip_select];
-		else
-			cs_pin = spi1_standard_cs[devices[i].chip_select];
-
-		if (!gpio_is_valid(cs_pin))
-			continue;
-
-		if (devices[i].bus_num == 0)
-			enable_spi0 = 1;
-		else
-			enable_spi1 = 1;
-
-		/* enable chip-select pin */
-		at91_set_gpio_output(cs_pin, 1);
-
-		/* pass chip-select pin to driver */
-		devices[i].controller_data = (void *) cs_pin;
-	}
-
-	spi_register_board_info(devices, nr_devices);
-
-	/* Configure SPI bus(es) */
-	if (enable_spi0) {
-		at91_set_A_periph(AT91_PIN_PA0, 0);	/* SPI0_MISO */
-		at91_set_A_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
-		at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPI1_SPCK */
-
-		platform_device_register(&at91sam9260_spi0_device);
-	}
-	if (enable_spi1) {
-		at91_set_A_periph(AT91_PIN_PB0, 0);	/* SPI1_MISO */
-		at91_set_A_periph(AT91_PIN_PB1, 0);	/* SPI1_MOSI */
-		at91_set_A_periph(AT91_PIN_PB2, 0);	/* SPI1_SPCK */
-
-		platform_device_register(&at91sam9260_spi1_device);
-	}
-}
-#else
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Timer/Counter blocks
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_ATMEL_TCLIB
-
-static struct resource tcb0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_TCB0,
-		.end	= AT91SAM9260_BASE_TCB0 + SZ_256 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC0,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[2] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC1,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[3] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC2,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_tcb0_device = {
-	.name		= "atmel_tcb",
-	.id		= 0,
-	.resource	= tcb0_resources,
-	.num_resources	= ARRAY_SIZE(tcb0_resources),
-};
-
-static struct resource tcb1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_TCB1,
-		.end	= AT91SAM9260_BASE_TCB1 + SZ_256 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC3,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC3,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[2] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC4,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC4,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[3] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC5,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_TC5,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_tcb1_device = {
-	.name		= "atmel_tcb",
-	.id		= 1,
-	.resource	= tcb1_resources,
-	.num_resources	= ARRAY_SIZE(tcb1_resources),
-};
-
-static void __init at91_add_device_tc(void)
-{
-	platform_device_register(&at91sam9260_tcb0_device);
-	platform_device_register(&at91sam9260_tcb1_device);
-}
-#else
-static void __init at91_add_device_tc(void) { }
-#endif
-
-
-/* --------------------------------------------------------------------
- *  RTT
- * -------------------------------------------------------------------- */
-
-static struct resource rtt_resources[] = {
-	{
-		.start	= AT91SAM9260_BASE_RTT,
-		.end	= AT91SAM9260_BASE_RTT + SZ_16 - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.flags  = IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_rtt_device = {
-	.name		= "at91_rtt",
-	.id		= 0,
-	.resource	= rtt_resources,
-};
-
-
-#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
-static void __init at91_add_device_rtt_rtc(void)
-{
-	at91sam9260_rtt_device.name = "rtc-at91sam9";
-	/*
-	 * The second resource is needed:
-	 * GPBR will serve as the storage for RTC time offset
-	 */
-	at91sam9260_rtt_device.num_resources = 3;
-	rtt_resources[1].start = AT91SAM9260_BASE_GPBR +
-				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
-	rtt_resources[1].end = rtt_resources[1].start + 3;
-	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
-	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
-}
-#else
-static void __init at91_add_device_rtt_rtc(void)
-{
-	/* Only one resource is needed: RTT not used as RTC */
-	at91sam9260_rtt_device.num_resources = 1;
-}
-#endif
-
-static void __init at91_add_device_rtt(void)
-{
-	at91_add_device_rtt_rtc();
-	platform_device_register(&at91sam9260_rtt_device);
-}
-
-
-/* --------------------------------------------------------------------
- *  Watchdog
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
-static struct resource wdt_resources[] = {
-	{
-		.start	= AT91SAM9260_BASE_WDT,
-		.end	= AT91SAM9260_BASE_WDT + SZ_16 - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device at91sam9260_wdt_device = {
-	.name		= "at91_wdt",
-	.id		= -1,
-	.resource	= wdt_resources,
-	.num_resources	= ARRAY_SIZE(wdt_resources),
-};
-
-static void __init at91_add_device_watchdog(void)
-{
-	platform_device_register(&at91sam9260_wdt_device);
-}
-#else
-static void __init at91_add_device_watchdog(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  SSC -- Synchronous Serial Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
-static u64 ssc_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_SSC,
-		.end	= AT91SAM9260_BASE_SSC + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_SSC,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_SSC,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_ssc_device = {
-	.name	= "at91rm9200_ssc",
-	.id	= 0,
-	.dev	= {
-		.dma_mask		= &ssc_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= ssc_resources,
-	.num_resources	= ARRAY_SIZE(ssc_resources),
-};
-
-static inline void configure_ssc_pins(unsigned pins)
-{
-	if (pins & ATMEL_SSC_TF)
-		at91_set_A_periph(AT91_PIN_PB17, 1);
-	if (pins & ATMEL_SSC_TK)
-		at91_set_A_periph(AT91_PIN_PB16, 1);
-	if (pins & ATMEL_SSC_TD)
-		at91_set_A_periph(AT91_PIN_PB18, 1);
-	if (pins & ATMEL_SSC_RD)
-		at91_set_A_periph(AT91_PIN_PB19, 1);
-	if (pins & ATMEL_SSC_RK)
-		at91_set_A_periph(AT91_PIN_PB20, 1);
-	if (pins & ATMEL_SSC_RF)
-		at91_set_A_periph(AT91_PIN_PB21, 1);
-}
-
-/*
- * SSC controllers are accessed through library code, instead of any
- * kind of all-singing/all-dancing driver.  For example one could be
- * used by a particular I2S audio codec's driver, while another one
- * on the same system might be used by a custom data capture driver.
- */
-void __init at91_add_device_ssc(unsigned id, unsigned pins)
-{
-	struct platform_device *pdev;
-
-	/*
-	 * NOTE: caller is responsible for passing information matching
-	 * "pins" to whatever will be using each particular controller.
-	 */
-	switch (id) {
-	case AT91SAM9260_ID_SSC:
-		pdev = &at91sam9260_ssc_device;
-		configure_ssc_pins(pins);
-		break;
-	default:
-		return;
-	}
-
-	platform_device_register(pdev);
-}
-
-#else
-void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  UART
- * -------------------------------------------------------------------- */
-#if defined(CONFIG_SERIAL_ATMEL)
-static struct resource dbgu_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_DBGU,
-		.end	= AT91SAM9260_BASE_DBGU + SZ_512 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.end	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data dbgu_data = {
-	.use_dma_tx	= 0,
-	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
-};
-
-static u64 dbgu_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9260_dbgu_device = {
-	.name		= "atmel_usart",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &dbgu_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &dbgu_data,
-	},
-	.resource	= dbgu_resources,
-	.num_resources	= ARRAY_SIZE(dbgu_resources),
-};
-
-static inline void configure_dbgu_pins(void)
-{
-	at91_set_A_periph(AT91_PIN_PB14, 0);		/* DRXD */
-	at91_set_A_periph(AT91_PIN_PB15, 1);		/* DTXD */
-}
-
-static struct resource uart0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_US0,
-		.end	= AT91SAM9260_BASE_US0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_US0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_US0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart0_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart0_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9260_uart0_device = {
-	.name		= "atmel_usart",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &uart0_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart0_data,
-	},
-	.resource	= uart0_resources,
-	.num_resources	= ARRAY_SIZE(uart0_resources),
-};
-
-static inline void configure_usart0_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PB4, 1);		/* TXD0 */
-	at91_set_A_periph(AT91_PIN_PB5, 0);		/* RXD0 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_A_periph(AT91_PIN_PB26, 0);	/* RTS0 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PB27, 0);	/* CTS0 */
-	if (pins & ATMEL_UART_DTR)
-		at91_set_A_periph(AT91_PIN_PB24, 0);	/* DTR0 */
-	if (pins & ATMEL_UART_DSR)
-		at91_set_A_periph(AT91_PIN_PB22, 0);	/* DSR0 */
-	if (pins & ATMEL_UART_DCD)
-		at91_set_A_periph(AT91_PIN_PB23, 0);	/* DCD0 */
-	if (pins & ATMEL_UART_RI)
-		at91_set_A_periph(AT91_PIN_PB25, 0);	/* RI0 */
-}
-
-static struct resource uart1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_US1,
-		.end	= AT91SAM9260_BASE_US1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_US1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_US1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart1_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart1_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9260_uart1_device = {
-	.name		= "atmel_usart",
-	.id		= 2,
-	.dev		= {
-				.dma_mask		= &uart1_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart1_data,
-	},
-	.resource	= uart1_resources,
-	.num_resources	= ARRAY_SIZE(uart1_resources),
-};
-
-static inline void configure_usart1_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PB6, 1);		/* TXD1 */
-	at91_set_A_periph(AT91_PIN_PB7, 0);		/* RXD1 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_A_periph(AT91_PIN_PB28, 0);	/* RTS1 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PB29, 0);	/* CTS1 */
-}
-
-static struct resource uart2_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_US2,
-		.end	= AT91SAM9260_BASE_US2 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_US2,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_US2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart2_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart2_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9260_uart2_device = {
-	.name		= "atmel_usart",
-	.id		= 3,
-	.dev		= {
-				.dma_mask		= &uart2_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart2_data,
-	},
-	.resource	= uart2_resources,
-	.num_resources	= ARRAY_SIZE(uart2_resources),
-};
-
-static inline void configure_usart2_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PB8, 1);		/* TXD2 */
-	at91_set_A_periph(AT91_PIN_PB9, 0);		/* RXD2 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_A_periph(AT91_PIN_PA4, 0);	/* RTS2 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PA5, 0);	/* CTS2 */
-}
-
-static struct resource uart3_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_US3,
-		.end	= AT91SAM9260_BASE_US3 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_US3,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_US3,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart3_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart3_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9260_uart3_device = {
-	.name		= "atmel_usart",
-	.id		= 4,
-	.dev		= {
-				.dma_mask		= &uart3_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart3_data,
-	},
-	.resource	= uart3_resources,
-	.num_resources	= ARRAY_SIZE(uart3_resources),
-};
-
-static inline void configure_usart3_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PB10, 1);		/* TXD3 */
-	at91_set_A_periph(AT91_PIN_PB11, 0);		/* RXD3 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_B_periph(AT91_PIN_PC8, 0);	/* RTS3 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_B_periph(AT91_PIN_PC10, 0);	/* CTS3 */
-}
-
-static struct resource uart4_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_US4,
-		.end	= AT91SAM9260_BASE_US4 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_US4,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_US4,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart4_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart4_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9260_uart4_device = {
-	.name		= "atmel_usart",
-	.id		= 5,
-	.dev		= {
-				.dma_mask		= &uart4_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart4_data,
-	},
-	.resource	= uart4_resources,
-	.num_resources	= ARRAY_SIZE(uart4_resources),
-};
-
-static inline void configure_usart4_pins(void)
-{
-	at91_set_B_periph(AT91_PIN_PA31, 1);		/* TXD4 */
-	at91_set_B_periph(AT91_PIN_PA30, 0);		/* RXD4 */
-}
-
-static struct resource uart5_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_US5,
-		.end	= AT91SAM9260_BASE_US5 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_US5,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_US5,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart5_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart5_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9260_uart5_device = {
-	.name		= "atmel_usart",
-	.id		= 6,
-	.dev		= {
-				.dma_mask		= &uart5_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart5_data,
-	},
-	.resource	= uart5_resources,
-	.num_resources	= ARRAY_SIZE(uart5_resources),
-};
-
-static inline void configure_usart5_pins(void)
-{
-	at91_set_A_periph(AT91_PIN_PB12, 1);		/* TXD5 */
-	at91_set_A_periph(AT91_PIN_PB13, 0);		/* RXD5 */
-}
-
-static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
-
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
-{
-	struct platform_device *pdev;
-	struct atmel_uart_data *pdata;
-
-	switch (id) {
-		case 0:		/* DBGU */
-			pdev = &at91sam9260_dbgu_device;
-			configure_dbgu_pins();
-			break;
-		case AT91SAM9260_ID_US0:
-			pdev = &at91sam9260_uart0_device;
-			configure_usart0_pins(pins);
-			break;
-		case AT91SAM9260_ID_US1:
-			pdev = &at91sam9260_uart1_device;
-			configure_usart1_pins(pins);
-			break;
-		case AT91SAM9260_ID_US2:
-			pdev = &at91sam9260_uart2_device;
-			configure_usart2_pins(pins);
-			break;
-		case AT91SAM9260_ID_US3:
-			pdev = &at91sam9260_uart3_device;
-			configure_usart3_pins(pins);
-			break;
-		case AT91SAM9260_ID_US4:
-			pdev = &at91sam9260_uart4_device;
-			configure_usart4_pins();
-			break;
-		case AT91SAM9260_ID_US5:
-			pdev = &at91sam9260_uart5_device;
-			configure_usart5_pins();
-			break;
-		default:
-			return;
-	}
-	pdata = pdev->dev.platform_data;
-	pdata->num = portnr;		/* update to mapped ID */
-
-	if (portnr < ATMEL_MAX_UART)
-		at91_uarts[portnr] = pdev;
-}
-
-void __init at91_add_device_serial(void)
-{
-	int i;
-
-	for (i = 0; i < ATMEL_MAX_UART; i++) {
-		if (at91_uarts[i])
-			platform_device_register(at91_uarts[i]);
-	}
-}
-#else
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_add_device_serial(void) {}
-#endif
-
-/* --------------------------------------------------------------------
- *  CF/IDE
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
-	defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
-
-static struct at91_cf_data cf0_data;
-
-static struct resource cf0_resources[] = {
-	[0] = {
-		.start	= AT91_CHIPSELECT_4,
-		.end	= AT91_CHIPSELECT_4 + SZ_256M - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device cf0_device = {
-	.id		= 0,
-	.dev		= {
-				.platform_data	= &cf0_data,
-	},
-	.resource	= cf0_resources,
-	.num_resources	= ARRAY_SIZE(cf0_resources),
-};
-
-static struct at91_cf_data cf1_data;
-
-static struct resource cf1_resources[] = {
-	[0] = {
-		.start	= AT91_CHIPSELECT_5,
-		.end	= AT91_CHIPSELECT_5 + SZ_256M - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device cf1_device = {
-	.id		= 1,
-	.dev		= {
-				.platform_data	= &cf1_data,
-	},
-	.resource	= cf1_resources,
-	.num_resources	= ARRAY_SIZE(cf1_resources),
-};
-
-void __init at91_add_device_cf(struct at91_cf_data *data)
-{
-	struct platform_device *pdev;
-	unsigned long csa;
-
-	if (!data)
-		return;
-
-	csa = at91_matrix_read(AT91_MATRIX_EBICSA);
-
-	switch (data->chipselect) {
-	case 4:
-		at91_set_multi_drive(AT91_PIN_PC8, 0);
-		at91_set_A_periph(AT91_PIN_PC8, 0);
-		csa |= AT91_MATRIX_CS4A_SMC_CF1;
-		cf0_data = *data;
-		pdev = &cf0_device;
-		break;
-	case 5:
-		at91_set_multi_drive(AT91_PIN_PC9, 0);
-		at91_set_A_periph(AT91_PIN_PC9, 0);
-		csa |= AT91_MATRIX_CS5A_SMC_CF2;
-		cf1_data = *data;
-		pdev = &cf1_device;
-		break;
-	default:
-		printk(KERN_ERR "AT91 CF: bad chip-select requested (%u)\n",
-		       data->chipselect);
-		return;
-	}
-
-	at91_matrix_write(AT91_MATRIX_EBICSA, csa);
-
-	if (gpio_is_valid(data->rst_pin)) {
-		at91_set_multi_drive(data->rst_pin, 0);
-		at91_set_gpio_output(data->rst_pin, 1);
-	}
-
-	if (gpio_is_valid(data->irq_pin)) {
-		at91_set_gpio_input(data->irq_pin, 0);
-		at91_set_deglitch(data->irq_pin, 1);
-	}
-
-	if (gpio_is_valid(data->det_pin)) {
-		at91_set_gpio_input(data->det_pin, 0);
-		at91_set_deglitch(data->det_pin, 1);
-	}
-
-	at91_set_B_periph(AT91_PIN_PC6, 0);     /* CFCE1 */
-	at91_set_B_periph(AT91_PIN_PC7, 0);     /* CFCE2 */
-	at91_set_A_periph(AT91_PIN_PC10, 0);    /* CFRNW */
-	at91_set_A_periph(AT91_PIN_PC15, 1);    /* NWAIT */
-
-	if (IS_ENABLED(CONFIG_PATA_AT91) && (data->flags & AT91_CF_TRUE_IDE))
-		pdev->name = "pata_at91";
-	else
-		pdev->name = "at91_cf";
-
-	platform_device_register(pdev);
-}
-
-#else
-void __init at91_add_device_cf(struct at91_cf_data * data) {}
-#endif
-
-/* --------------------------------------------------------------------
- *  ADCs
- * -------------------------------------------------------------------- */
-
-#if IS_ENABLED(CONFIG_AT91_ADC)
-static struct at91_adc_data adc_data;
-
-static struct resource adc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_ADC,
-		.end	= AT91SAM9260_BASE_ADC + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_ADC,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_ADC,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91_adc_device = {
-	.name		= "at91sam9260-adc",
-	.id		= -1,
-	.dev		= {
-				.platform_data		= &adc_data,
-	},
-	.resource	= adc_resources,
-	.num_resources	= ARRAY_SIZE(adc_resources),
-};
-
-static struct at91_adc_trigger at91_adc_triggers[] = {
-	[0] = {
-		.name = "timer-counter-0",
-		.value = 0x1,
-	},
-	[1] = {
-		.name = "timer-counter-1",
-		.value = 0x3,
-	},
-	[2] = {
-		.name = "timer-counter-2",
-		.value = 0x5,
-	},
-	[3] = {
-		.name = "external",
-		.value = 0xd,
-		.is_external = true,
-	},
-};
-
-void __init at91_add_device_adc(struct at91_adc_data *data)
-{
-	if (!data)
-		return;
-
-	if (test_bit(0, &data->channels_used))
-		at91_set_A_periph(AT91_PIN_PC0, 0);
-	if (test_bit(1, &data->channels_used))
-		at91_set_A_periph(AT91_PIN_PC1, 0);
-	if (test_bit(2, &data->channels_used))
-		at91_set_A_periph(AT91_PIN_PC2, 0);
-	if (test_bit(3, &data->channels_used))
-		at91_set_A_periph(AT91_PIN_PC3, 0);
-
-	if (data->use_external_triggers)
-		at91_set_A_periph(AT91_PIN_PA22, 0);
-
-	data->startup_time = 10;
-	data->trigger_number = 4;
-	data->trigger_list = at91_adc_triggers;
-
-	adc_data = *data;
-	platform_device_register(&at91_adc_device);
-}
-#else
-void __init at91_add_device_adc(struct at91_adc_data *data) {}
-#endif
-
-/* -------------------------------------------------------------------- */
-/*
- * These devices are always present and don't need any board-specific
- * setup.
- */
-static int __init at91_add_standard_devices(void)
-{
-	if (of_have_populated_dt())
-		return 0;
-
-	at91_add_device_rtt();
-	at91_add_device_watchdog();
-	at91_add_device_tc();
-	return 0;
-}
-
-arch_initcall(at91_add_standard_devices);

arch/arm/mach-at91/at91sam9261.c

@@ -10,284 +10,12 @@
  *
  */
 
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk/at91_pmc.h>
-
-#include <asm/proc-fns.h>
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
 #include <asm/system_misc.h>
 #include <mach/cpu.h>
-#include <mach/at91sam9261.h>
 #include <mach/hardware.h>
 
-#include "at91_aic.h"
 #include "soc.h"
 #include "generic.h"
-#include "sam9_smc.h"
-#include "pm.h"
-
-#if defined(CONFIG_OLD_CLK_AT91)
-#include "clock.h"
-
-/* --------------------------------------------------------------------
- *  Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk pioA_clk = {
-	.name		= "pioA_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_PIOA,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioB_clk = {
-	.name		= "pioB_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_PIOB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioC_clk = {
-	.name		= "pioC_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_PIOC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
-	.name		= "usart0_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_US0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
-	.name		= "usart1_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_US1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
-	.name		= "usart2_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_US2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc_clk = {
-	.name		= "mci_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_MCI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk udc_clk = {
-	.name		= "udc_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_UDP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi_clk = {
-	.name		= "twi_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_TWI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi0_clk = {
-	.name		= "spi0_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_SPI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi1_clk = {
-	.name		= "spi1_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_SPI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc0_clk = {
-	.name		= "ssc0_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_SSC0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc1_clk = {
-	.name		= "ssc1_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_SSC1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc2_clk = {
-	.name		= "ssc2_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_SSC2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc0_clk = {
-	.name		= "tc0_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_TC0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc1_clk = {
-	.name		= "tc1_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_TC1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc2_clk = {
-	.name		= "tc2_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_TC2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ohci_clk = {
-	.name		= "ohci_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_UHP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk lcdc_clk = {
-	.name		= "lcdc_clk",
-	.pmc_mask	= 1 << AT91SAM9261_ID_LCDC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-
-/* HClocks */
-static struct clk hck0 = {
-	.name		= "hck0",
-	.pmc_mask	= AT91_PMC_HCK0,
-	.type		= CLK_TYPE_SYSTEM,
-	.id		= 0,
-};
-static struct clk hck1 = {
-	.name		= "hck1",
-	.pmc_mask	= AT91_PMC_HCK1,
-	.type		= CLK_TYPE_SYSTEM,
-	.id		= 1,
-};
-
-static struct clk *periph_clocks[] __initdata = {
-	&pioA_clk,
-	&pioB_clk,
-	&pioC_clk,
-	&usart0_clk,
-	&usart1_clk,
-	&usart2_clk,
-	&mmc_clk,
-	&udc_clk,
-	&twi_clk,
-	&spi0_clk,
-	&spi1_clk,
-	&ssc0_clk,
-	&ssc1_clk,
-	&ssc2_clk,
-	&tc0_clk,
-	&tc1_clk,
-	&tc2_clk,
-	&ohci_clk,
-	&lcdc_clk,
-	// irq0 .. irq2
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("hclk", "at91sam9261-lcdfb.0", &hck1),
-	CLKDEV_CON_DEV_ID("hclk", "at91sam9g10-lcdfb.0", &hck1),
-	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
-	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.0", &ssc0_clk),
-	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.1", &ssc1_clk),
-	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.2", &ssc2_clk),
-	CLKDEV_CON_DEV_ID("pclk", "fffbc000.ssc", &ssc0_clk),
-	CLKDEV_CON_DEV_ID("pclk", "fffc0000.ssc", &ssc1_clk),
-	CLKDEV_CON_DEV_ID("pclk", "fffc4000.ssc", &ssc2_clk),
-	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &hck0),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9261.0", &twi_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g10.0", &twi_clk),
-	CLKDEV_CON_ID("pioA", &pioA_clk),
-	CLKDEV_CON_ID("pioB", &pioB_clk),
-	CLKDEV_CON_ID("pioC", &pioC_clk),
-	CLKDEV_CON_DEV_ID(NULL, "rtc-at91sam9.0", &clk32k),
-	/* more lookup table for DT entries */
-	CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
-	CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "ffffb400.serial", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "fffa0000.timer", &tc1_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "fffa0000.timer", &tc2_clk),
-	CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &hck0),
-	CLKDEV_CON_DEV_ID("hclk", "600000.fb", &hck1),
-	CLKDEV_CON_DEV_ID("spi_clk", "fffc8000.spi", &spi0_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "fffcc000.spi", &spi1_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "fffa8000.mmc", &mmc_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffac000.i2c", &twi_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffffd20.rtc", &clk32k),
-};
-
-static struct clk_lookup usart_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
-};
-
-/*
- * The four programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
-	.name		= "pck0",
-	.pmc_mask	= AT91_PMC_PCK0,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 0,
-};
-static struct clk pck1 = {
-	.name		= "pck1",
-	.pmc_mask	= AT91_PMC_PCK1,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 1,
-};
-static struct clk pck2 = {
-	.name		= "pck2",
-	.pmc_mask	= AT91_PMC_PCK2,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 2,
-};
-static struct clk pck3 = {
-	.name		= "pck3",
-	.pmc_mask	= AT91_PMC_PCK3,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 3,
-};
-
-static void __init at91sam9261_register_clocks(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
-		clk_register(periph_clocks[i]);
-
-	clkdev_add_table(periph_clocks_lookups,
-			 ARRAY_SIZE(periph_clocks_lookups));
-	clkdev_add_table(usart_clocks_lookups,
-			 ARRAY_SIZE(usart_clocks_lookups));
-
-	clk_register(&pck0);
-	clk_register(&pck1);
-	clk_register(&pck2);
-	clk_register(&pck3);
-
-	clk_register(&hck0);
-	clk_register(&hck1);
-}
-#else
-#define at91sam9261_register_clocks NULL
-#endif
-/* --------------------------------------------------------------------
- *  GPIO
- * -------------------------------------------------------------------- */
-
-static struct at91_gpio_bank at91sam9261_gpio[] __initdata = {
-	{
-		.id		= AT91SAM9261_ID_PIOA,
-		.regbase	= AT91SAM9261_BASE_PIOA,
-	}, {
-		.id		= AT91SAM9261_ID_PIOB,
-		.regbase	= AT91SAM9261_BASE_PIOB,
-	}, {
-		.id		= AT91SAM9261_ID_PIOC,
-		.regbase	= AT91SAM9261_BASE_PIOC,
-	}
-};
 
 /* --------------------------------------------------------------------
  *  AT91SAM9261 processor initialization
@@ -301,119 +29,14 @@ static void __init at91sam9261_map_io(void)
 		at91_init_sram(0, AT91SAM9261_SRAM_BASE, AT91SAM9261_SRAM_SIZE);
 }
 
-static void __init at91sam9261_ioremap_registers(void)
-{
-	at91_ioremap_ramc(0, AT91SAM9261_BASE_SDRAMC, 512);
-	at91sam926x_ioremap_pit(AT91SAM9261_BASE_PIT);
-	at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC);
-	at91_ioremap_matrix(AT91SAM9261_BASE_MATRIX);
-	at91_pm_set_standby(at91sam9_sdram_standby);
-}
-
 static void __init at91sam9261_initialize(void)
 {
 	arm_pm_idle = at91sam9_idle;
 
 	at91_sysirq_mask_rtt(AT91SAM9261_BASE_RTT);
-
-	/* Register GPIO subsystem */
-	at91_gpio_init(at91sam9261_gpio, 3);
-}
-
-static struct resource rstc_resources[] = {
-	[0] = {
-		.start  = AT91SAM9261_BASE_RSTC,
-		.end    = AT91SAM9261_BASE_RSTC + SZ_16 - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start  = AT91SAM9261_BASE_SDRAMC,
-		.end    = AT91SAM9261_BASE_SDRAMC + SZ_512 - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device rstc_device = {
-	.name           = "at91-sam9260-reset",
-	.resource       = rstc_resources,
-	.num_resources  = ARRAY_SIZE(rstc_resources),
-};
-
-static struct resource shdwc_resources[] = {
-	[0] = {
-		.start  = AT91SAM9261_BASE_SHDWC,
-		.end    = AT91SAM9261_BASE_SHDWC + SZ_16 - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device shdwc_device = {
-	.name           = "at91-poweroff",
-	.resource       = shdwc_resources,
-	.num_resources  = ARRAY_SIZE(shdwc_resources),
-};
-
-static void __init at91sam9261_register_devices(void)
-{
-	platform_device_register(&rstc_device);
-	platform_device_register(&shdwc_device);
-}
-
-/* --------------------------------------------------------------------
- *  Interrupt initialization
- * -------------------------------------------------------------------- */
-
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = {
-	7,	/* Advanced Interrupt Controller */
-	7,	/* System Peripherals */
-	1,	/* Parallel IO Controller A */
-	1,	/* Parallel IO Controller B */
-	1,	/* Parallel IO Controller C */
-	0,
-	5,	/* USART 0 */
-	5,	/* USART 1 */
-	5,	/* USART 2 */
-	0,	/* Multimedia Card Interface */
-	2,	/* USB Device Port */
-	6,	/* Two-Wire Interface */
-	5,	/* Serial Peripheral Interface 0 */
-	5,	/* Serial Peripheral Interface 1 */
-	4,	/* Serial Synchronous Controller 0 */
-	4,	/* Serial Synchronous Controller 1 */
-	4,	/* Serial Synchronous Controller 2 */
-	0,	/* Timer Counter 0 */
-	0,	/* Timer Counter 1 */
-	0,	/* Timer Counter 2 */
-	2,	/* USB Host port */
-	3,	/* LCD Controller */
-	0,
-	0,
-	0,
-	0,
-	0,
-	0,
-	0,
-	0,	/* Advanced Interrupt Controller */
-	0,	/* Advanced Interrupt Controller */
-	0,	/* Advanced Interrupt Controller */
-};
-
-static void __init at91sam9261_init_time(void)
-{
-	at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
 }
 
 AT91_SOC_START(at91sam9261)
 	.map_io = at91sam9261_map_io,
-	.default_irq_priority = at91sam9261_default_irq_priority,
-	.extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1)
-		    | (1 << AT91SAM9261_ID_IRQ2),
-	.ioremap_registers = at91sam9261_ioremap_registers,
-	.register_clocks = at91sam9261_register_clocks,
-	.register_devices = at91sam9261_register_devices,
 	.init = at91sam9261_initialize,
-	.init_time = at91sam9261_init_time,
 AT91_SOC_END

arch/arm/mach-at91/at91sam9261_devices.c

@@ -1,1098 +0,0 @@
-/*
- * arch/arm/mach-at91/at91sam9261_devices.c
- *
- *  Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
- *  Copyright (C) 2005 David Brownell
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/i2c-gpio.h>
-
-#include <linux/fb.h>
-#include <video/atmel_lcdc.h>
-
-#include <mach/at91sam9261.h>
-#include <mach/at91sam9261_matrix.h>
-#include <mach/at91_matrix.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/hardware.h>
-
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-/* --------------------------------------------------------------------
- *  USB Host
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-static struct at91_usbh_data usbh_data;
-
-static struct resource usbh_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_UHP_BASE,
-		.end	= AT91SAM9261_UHP_BASE + SZ_1M - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_UHP,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_UHP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_usbh_device = {
-	.name		= "at91_ohci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &ohci_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &usbh_data,
-	},
-	.resource	= usbh_resources,
-	.num_resources	= ARRAY_SIZE(usbh_resources),
-};
-
-void __init at91_add_device_usbh(struct at91_usbh_data *data)
-{
-	int i;
-
-	if (!data)
-		return;
-
-	/* Enable overcurrent notification */
-	for (i = 0; i < data->ports; i++) {
-		if (gpio_is_valid(data->overcurrent_pin[i]))
-			at91_set_gpio_input(data->overcurrent_pin[i], 1);
-	}
-
-	usbh_data = *data;
-	platform_device_register(&at91sam9261_usbh_device);
-}
-#else
-void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  USB Device (Gadget)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
-static struct at91_udc_data udc_data;
-
-static struct resource udc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_UDP,
-		.end	= AT91SAM9261_BASE_UDP + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_UDP,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_UDP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_udc_device = {
-	.name		= "at91_udc",
-	.id		= -1,
-	.dev		= {
-				.platform_data		= &udc_data,
-	},
-	.resource	= udc_resources,
-	.num_resources	= ARRAY_SIZE(udc_resources),
-};
-
-void __init at91_add_device_udc(struct at91_udc_data *data)
-{
-	if (!data)
-		return;
-
-	if (gpio_is_valid(data->vbus_pin)) {
-		at91_set_gpio_input(data->vbus_pin, 0);
-		at91_set_deglitch(data->vbus_pin, 1);
-	}
-
-	/* Pullup pin is handled internally by USB device peripheral */
-
-	udc_data = *data;
-	platform_device_register(&at91sam9261_udc_device);
-}
-#else
-void __init at91_add_device_udc(struct at91_udc_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- *  MMC / SD
- * -------------------------------------------------------------------- */
-
-#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct mci_platform_data mmc_data;
-
-static struct resource mmc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_MCI,
-		.end	= AT91SAM9261_BASE_MCI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_MCI,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_MCI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_mmc_device = {
-	.name		= "atmel_mci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &mmc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &mmc_data,
-	},
-	.resource	= mmc_resources,
-	.num_resources	= ARRAY_SIZE(mmc_resources),
-};
-
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
-{
-	if (!data)
-		return;
-
-	if (data->slot[0].bus_width) {
-		/* input/irq */
-		if (gpio_is_valid(data->slot[0].detect_pin)) {
-			at91_set_gpio_input(data->slot[0].detect_pin, 1);
-			at91_set_deglitch(data->slot[0].detect_pin, 1);
-		}
-		if (gpio_is_valid(data->slot[0].wp_pin))
-			at91_set_gpio_input(data->slot[0].wp_pin, 1);
-
-		/* CLK */
-		at91_set_B_periph(AT91_PIN_PA2, 0);
-
-		/* CMD */
-		at91_set_B_periph(AT91_PIN_PA1, 1);
-
-		/* DAT0, maybe DAT1..DAT3 */
-		at91_set_B_periph(AT91_PIN_PA0, 1);
-		if (data->slot[0].bus_width == 4) {
-			at91_set_B_periph(AT91_PIN_PA4, 1);
-			at91_set_B_periph(AT91_PIN_PA5, 1);
-			at91_set_B_periph(AT91_PIN_PA6, 1);
-		}
-
-		mmc_data = *data;
-		platform_device_register(&at91sam9261_mmc_device);
-	}
-}
-#else
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  NAND / SmartMedia
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
-static struct atmel_nand_data nand_data;
-
-#define NAND_BASE	AT91_CHIPSELECT_3
-
-static struct resource nand_resources[] = {
-	{
-		.start	= NAND_BASE,
-		.end	= NAND_BASE + SZ_256M - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device atmel_nand_device = {
-	.name		= "atmel_nand",
-	.id		= -1,
-	.dev		= {
-				.platform_data	= &nand_data,
-	},
-	.resource	= nand_resources,
-	.num_resources	= ARRAY_SIZE(nand_resources),
-};
-
-void __init at91_add_device_nand(struct atmel_nand_data *data)
-{
-	unsigned long csa;
-
-	if (!data)
-		return;
-
-	csa = at91_matrix_read(AT91_MATRIX_EBICSA);
-	at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
-
-	/* enable pin */
-	if (gpio_is_valid(data->enable_pin))
-		at91_set_gpio_output(data->enable_pin, 1);
-
-	/* ready/busy pin */
-	if (gpio_is_valid(data->rdy_pin))
-		at91_set_gpio_input(data->rdy_pin, 1);
-
-	/* card detect pin */
-	if (gpio_is_valid(data->det_pin))
-		at91_set_gpio_input(data->det_pin, 1);
-
-	at91_set_A_periph(AT91_PIN_PC0, 0);		/* NANDOE */
-	at91_set_A_periph(AT91_PIN_PC1, 0);		/* NANDWE */
-
-	nand_data = *data;
-	platform_device_register(&atmel_nand_device);
-}
-
-#else
-void __init at91_add_device_nand(struct atmel_nand_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  TWI (i2c)
- * -------------------------------------------------------------------- */
-
-/*
- * Prefer the GPIO code since the TWI controller isn't robust
- * (gets overruns and underruns under load) and can only issue
- * repeated STARTs in one scenario (the driver doesn't yet handle them).
- */
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
-
-static struct i2c_gpio_platform_data pdata = {
-	.sda_pin		= AT91_PIN_PA7,
-	.sda_is_open_drain	= 1,
-	.scl_pin		= AT91_PIN_PA8,
-	.scl_is_open_drain	= 1,
-	.udelay			= 2,		/* ~100 kHz */
-};
-
-static struct platform_device at91sam9261_twi_device = {
-	.name			= "i2c-gpio",
-	.id			= 0,
-	.dev.platform_data	= &pdata,
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	at91_set_GPIO_periph(AT91_PIN_PA7, 1);		/* TWD (SDA) */
-	at91_set_multi_drive(AT91_PIN_PA7, 1);
-
-	at91_set_GPIO_periph(AT91_PIN_PA8, 1);		/* TWCK (SCL) */
-	at91_set_multi_drive(AT91_PIN_PA8, 1);
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at91sam9261_twi_device);
-}
-
-#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
-
-static struct resource twi_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_TWI,
-		.end	= AT91SAM9261_BASE_TWI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_TWI,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_TWI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_twi_device = {
-	.id		= 0,
-	.resource	= twi_resources,
-	.num_resources	= ARRAY_SIZE(twi_resources),
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	/* IP version is not the same on 9261 and g10 */
-	if (cpu_is_at91sam9g10()) {
-		at91sam9261_twi_device.name = "i2c-at91sam9g10";
-		/* I2C PIO must not be configured as open-drain on this chip */
-	} else {
-		at91sam9261_twi_device.name = "i2c-at91sam9261";
-		at91_set_multi_drive(AT91_PIN_PA7, 1);
-		at91_set_multi_drive(AT91_PIN_PA8, 1);
-	}
-
-	/* pins used for TWI interface */
-	at91_set_A_periph(AT91_PIN_PA7, 0);		/* TWD */
-	at91_set_A_periph(AT91_PIN_PA8, 0);		/* TWCK */
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at91sam9261_twi_device);
-}
-#else
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  SPI
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct resource spi0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_SPI0,
-		.end	= AT91SAM9261_BASE_SPI0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_SPI0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_SPI0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_spi0_device = {
-	.name		= "atmel_spi",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &spi_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= spi0_resources,
-	.num_resources	= ARRAY_SIZE(spi0_resources),
-};
-
-static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
-
-static struct resource spi1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_SPI1,
-		.end	= AT91SAM9261_BASE_SPI1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_SPI1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_SPI1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_spi1_device = {
-	.name		= "atmel_spi",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &spi_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= spi1_resources,
-	.num_resources	= ARRAY_SIZE(spi1_resources),
-};
-
-static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB28, AT91_PIN_PA24, AT91_PIN_PA25, AT91_PIN_PA26 };
-
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
-{
-	int i;
-	unsigned long cs_pin;
-	short enable_spi0 = 0;
-	short enable_spi1 = 0;
-
-	/* Choose SPI chip-selects */
-	for (i = 0; i < nr_devices; i++) {
-		if (devices[i].controller_data)
-			cs_pin = (unsigned long) devices[i].controller_data;
-		else if (devices[i].bus_num == 0)
-			cs_pin = spi0_standard_cs[devices[i].chip_select];
-		else
-			cs_pin = spi1_standard_cs[devices[i].chip_select];
-
-		if (!gpio_is_valid(cs_pin))
-			continue;
-
-		if (devices[i].bus_num == 0)
-			enable_spi0 = 1;
-		else
-			enable_spi1 = 1;
-
-		/* enable chip-select pin */
-		at91_set_gpio_output(cs_pin, 1);
-
-		/* pass chip-select pin to driver */
-		devices[i].controller_data = (void *) cs_pin;
-	}
-
-	spi_register_board_info(devices, nr_devices);
-
-	/* Configure SPI bus(es) */
-	if (enable_spi0) {
-		at91_set_A_periph(AT91_PIN_PA0, 0);	/* SPI0_MISO */
-		at91_set_A_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
-		at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPI0_SPCK */
-
-		platform_device_register(&at91sam9261_spi0_device);
-	}
-	if (enable_spi1) {
-		at91_set_A_periph(AT91_PIN_PB30, 0);	/* SPI1_MISO */
-		at91_set_A_periph(AT91_PIN_PB31, 0);	/* SPI1_MOSI */
-		at91_set_A_periph(AT91_PIN_PB29, 0);	/* SPI1_SPCK */
-
-		platform_device_register(&at91sam9261_spi1_device);
-	}
-}
-#else
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  LCD Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_pdata lcdc_data;
-
-static struct resource lcdc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_LCDC_BASE,
-		.end	= AT91SAM9261_LCDC_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_LCDC,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_LCDC,
-		.flags	= IORESOURCE_IRQ,
-	},
-#if defined(CONFIG_FB_INTSRAM)
-	[2] = {
-		.start	= AT91SAM9261_SRAM_BASE,
-		.end	= AT91SAM9261_SRAM_BASE + AT91SAM9261_SRAM_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-#endif
-};
-
-static struct platform_device at91_lcdc_device = {
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &lcdc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &lcdc_data,
-	},
-	.resource	= lcdc_resources,
-	.num_resources	= ARRAY_SIZE(lcdc_resources),
-};
-
-void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
-{
-	if (!data) {
-		return;
-	}
-
-	if (cpu_is_at91sam9g10())
-		at91_lcdc_device.name = "at91sam9g10-lcdfb";
-	else
-		at91_lcdc_device.name = "at91sam9261-lcdfb";
-
-#if defined(CONFIG_FB_ATMEL_STN)
-	at91_set_A_periph(AT91_PIN_PB0, 0);     /* LCDVSYNC */
-	at91_set_A_periph(AT91_PIN_PB1, 0);     /* LCDHSYNC */
-	at91_set_A_periph(AT91_PIN_PB2, 0);     /* LCDDOTCK */
-	at91_set_A_periph(AT91_PIN_PB3, 0);     /* LCDDEN */
-	at91_set_A_periph(AT91_PIN_PB4, 0);     /* LCDCC */
-	at91_set_A_periph(AT91_PIN_PB5, 0);     /* LCDD0 */
-	at91_set_A_periph(AT91_PIN_PB6, 0);     /* LCDD1 */
-	at91_set_A_periph(AT91_PIN_PB7, 0);     /* LCDD2 */
-	at91_set_A_periph(AT91_PIN_PB8, 0);     /* LCDD3 */
-#else
-	at91_set_A_periph(AT91_PIN_PB1, 0);	/* LCDHSYNC */
-	at91_set_A_periph(AT91_PIN_PB2, 0);	/* LCDDOTCK */
-	at91_set_A_periph(AT91_PIN_PB3, 0);	/* LCDDEN */
-	at91_set_A_periph(AT91_PIN_PB4, 0);	/* LCDCC */
-	at91_set_A_periph(AT91_PIN_PB7, 0);	/* LCDD2 */
-	at91_set_A_periph(AT91_PIN_PB8, 0);	/* LCDD3 */
-	at91_set_A_periph(AT91_PIN_PB9, 0);	/* LCDD4 */
-	at91_set_A_periph(AT91_PIN_PB10, 0);	/* LCDD5 */
-	at91_set_A_periph(AT91_PIN_PB11, 0);	/* LCDD6 */
-	at91_set_A_periph(AT91_PIN_PB12, 0);	/* LCDD7 */
-	at91_set_A_periph(AT91_PIN_PB15, 0);	/* LCDD10 */
-	at91_set_A_periph(AT91_PIN_PB16, 0);	/* LCDD11 */
-	at91_set_A_periph(AT91_PIN_PB17, 0);	/* LCDD12 */
-	at91_set_A_periph(AT91_PIN_PB18, 0);	/* LCDD13 */
-	at91_set_A_periph(AT91_PIN_PB19, 0);	/* LCDD14 */
-	at91_set_A_periph(AT91_PIN_PB20, 0);	/* LCDD15 */
-	at91_set_B_periph(AT91_PIN_PB23, 0);	/* LCDD18 */
-	at91_set_B_periph(AT91_PIN_PB24, 0);	/* LCDD19 */
-	at91_set_B_periph(AT91_PIN_PB25, 0);	/* LCDD20 */
-	at91_set_B_periph(AT91_PIN_PB26, 0);	/* LCDD21 */
-	at91_set_B_periph(AT91_PIN_PB27, 0);	/* LCDD22 */
-	at91_set_B_periph(AT91_PIN_PB28, 0);	/* LCDD23 */
-#endif
-
-	if (ARRAY_SIZE(lcdc_resources) > 2) {
-		void __iomem *fb;
-		struct resource *fb_res = &lcdc_resources[2];
-		size_t fb_len = resource_size(fb_res);
-
-		fb = ioremap(fb_res->start, fb_len);
-		if (fb) {
-			memset(fb, 0, fb_len);
-			iounmap(fb);
-		}
-	}
-	lcdc_data = *data;
-	platform_device_register(&at91_lcdc_device);
-}
-#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Timer/Counter block
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_ATMEL_TCLIB
-
-static struct resource tcb_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_TCB0,
-		.end	= AT91SAM9261_BASE_TCB0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_TC0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_TC0,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[2] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_TC1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_TC1,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[3] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_TC2,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_TC2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_tcb_device = {
-	.name		= "atmel_tcb",
-	.id		= 0,
-	.resource	= tcb_resources,
-	.num_resources	= ARRAY_SIZE(tcb_resources),
-};
-
-static void __init at91_add_device_tc(void)
-{
-	platform_device_register(&at91sam9261_tcb_device);
-}
-#else
-static void __init at91_add_device_tc(void) { }
-#endif
-
-
-/* --------------------------------------------------------------------
- *  RTT
- * -------------------------------------------------------------------- */
-
-static struct resource rtt_resources[] = {
-	{
-		.start	= AT91SAM9261_BASE_RTT,
-		.end	= AT91SAM9261_BASE_RTT + SZ_16 - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.flags  = IORESOURCE_IRQ,
-	}
-};
-
-static struct platform_device at91sam9261_rtt_device = {
-	.name		= "at91_rtt",
-	.id		= 0,
-	.resource	= rtt_resources,
-};
-
-#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
-static void __init at91_add_device_rtt_rtc(void)
-{
-	at91sam9261_rtt_device.name = "rtc-at91sam9";
-	/*
-	 * The second resource is needed:
-	 * GPBR will serve as the storage for RTC time offset
-	 */
-	at91sam9261_rtt_device.num_resources = 3;
-	rtt_resources[1].start = AT91SAM9261_BASE_GPBR +
-				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
-	rtt_resources[1].end = rtt_resources[1].start + 3;
-	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
-	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
-}
-#else
-static void __init at91_add_device_rtt_rtc(void)
-{
-	/* Only one resource is needed: RTT not used as RTC */
-	at91sam9261_rtt_device.num_resources = 1;
-}
-#endif
-
-static void __init at91_add_device_rtt(void)
-{
-	at91_add_device_rtt_rtc();
-	platform_device_register(&at91sam9261_rtt_device);
-}
-
-
-/* --------------------------------------------------------------------
- *  Watchdog
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
-static struct resource wdt_resources[] = {
-	{
-		.start	= AT91SAM9261_BASE_WDT,
-		.end	= AT91SAM9261_BASE_WDT + SZ_16 - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device at91sam9261_wdt_device = {
-	.name		= "at91_wdt",
-	.id		= -1,
-	.resource	= wdt_resources,
-	.num_resources	= ARRAY_SIZE(wdt_resources),
-};
-
-static void __init at91_add_device_watchdog(void)
-{
-	platform_device_register(&at91sam9261_wdt_device);
-}
-#else
-static void __init at91_add_device_watchdog(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  SSC -- Synchronous Serial Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
-static u64 ssc0_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_SSC0,
-		.end	= AT91SAM9261_BASE_SSC0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_SSC0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_SSC0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_ssc0_device = {
-	.name	= "at91rm9200_ssc",
-	.id	= 0,
-	.dev	= {
-		.dma_mask		= &ssc0_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= ssc0_resources,
-	.num_resources	= ARRAY_SIZE(ssc0_resources),
-};
-
-static inline void configure_ssc0_pins(unsigned pins)
-{
-	if (pins & ATMEL_SSC_TF)
-		at91_set_A_periph(AT91_PIN_PB21, 1);
-	if (pins & ATMEL_SSC_TK)
-		at91_set_A_periph(AT91_PIN_PB22, 1);
-	if (pins & ATMEL_SSC_TD)
-		at91_set_A_periph(AT91_PIN_PB23, 1);
-	if (pins & ATMEL_SSC_RD)
-		at91_set_A_periph(AT91_PIN_PB24, 1);
-	if (pins & ATMEL_SSC_RK)
-		at91_set_A_periph(AT91_PIN_PB25, 1);
-	if (pins & ATMEL_SSC_RF)
-		at91_set_A_periph(AT91_PIN_PB26, 1);
-}
-
-static u64 ssc1_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_SSC1,
-		.end	= AT91SAM9261_BASE_SSC1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_SSC1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_SSC1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_ssc1_device = {
-	.name	= "at91rm9200_ssc",
-	.id	= 1,
-	.dev	= {
-		.dma_mask		= &ssc1_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= ssc1_resources,
-	.num_resources	= ARRAY_SIZE(ssc1_resources),
-};
-
-static inline void configure_ssc1_pins(unsigned pins)
-{
-	if (pins & ATMEL_SSC_TF)
-		at91_set_B_periph(AT91_PIN_PA17, 1);
-	if (pins & ATMEL_SSC_TK)
-		at91_set_B_periph(AT91_PIN_PA18, 1);
-	if (pins & ATMEL_SSC_TD)
-		at91_set_B_periph(AT91_PIN_PA19, 1);
-	if (pins & ATMEL_SSC_RD)
-		at91_set_B_periph(AT91_PIN_PA20, 1);
-	if (pins & ATMEL_SSC_RK)
-		at91_set_B_periph(AT91_PIN_PA21, 1);
-	if (pins & ATMEL_SSC_RF)
-		at91_set_B_periph(AT91_PIN_PA22, 1);
-}
-
-static u64 ssc2_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc2_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_SSC2,
-		.end	= AT91SAM9261_BASE_SSC2 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_SSC2,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_SSC2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9261_ssc2_device = {
-	.name	= "at91rm9200_ssc",
-	.id	= 2,
-	.dev	= {
-		.dma_mask		= &ssc2_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= ssc2_resources,
-	.num_resources	= ARRAY_SIZE(ssc2_resources),
-};
-
-static inline void configure_ssc2_pins(unsigned pins)
-{
-	if (pins & ATMEL_SSC_TF)
-		at91_set_B_periph(AT91_PIN_PC25, 1);
-	if (pins & ATMEL_SSC_TK)
-		at91_set_B_periph(AT91_PIN_PC26, 1);
-	if (pins & ATMEL_SSC_TD)
-		at91_set_B_periph(AT91_PIN_PC27, 1);
-	if (pins & ATMEL_SSC_RD)
-		at91_set_B_periph(AT91_PIN_PC28, 1);
-	if (pins & ATMEL_SSC_RK)
-		at91_set_B_periph(AT91_PIN_PC29, 1);
-	if (pins & ATMEL_SSC_RF)
-		at91_set_B_periph(AT91_PIN_PC30, 1);
-}
-
-/*
- * SSC controllers are accessed through library code, instead of any
- * kind of all-singing/all-dancing driver.  For example one could be
- * used by a particular I2S audio codec's driver, while another one
- * on the same system might be used by a custom data capture driver.
- */
-void __init at91_add_device_ssc(unsigned id, unsigned pins)
-{
-	struct platform_device *pdev;
-
-	/*
-	 * NOTE: caller is responsible for passing information matching
-	 * "pins" to whatever will be using each particular controller.
-	 */
-	switch (id) {
-	case AT91SAM9261_ID_SSC0:
-		pdev = &at91sam9261_ssc0_device;
-		configure_ssc0_pins(pins);
-		break;
-	case AT91SAM9261_ID_SSC1:
-		pdev = &at91sam9261_ssc1_device;
-		configure_ssc1_pins(pins);
-		break;
-	case AT91SAM9261_ID_SSC2:
-		pdev = &at91sam9261_ssc2_device;
-		configure_ssc2_pins(pins);
-		break;
-	default:
-		return;
-	}
-
-	platform_device_register(pdev);
-}
-
-#else
-void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  UART
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SERIAL_ATMEL)
-static struct resource dbgu_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_DBGU,
-		.end	= AT91SAM9261_BASE_DBGU + SZ_512 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.end	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data dbgu_data = {
-	.use_dma_tx	= 0,
-	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
-};
-
-static u64 dbgu_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9261_dbgu_device = {
-	.name		= "atmel_usart",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &dbgu_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &dbgu_data,
-	},
-	.resource	= dbgu_resources,
-	.num_resources	= ARRAY_SIZE(dbgu_resources),
-};
-
-static inline void configure_dbgu_pins(void)
-{
-	at91_set_A_periph(AT91_PIN_PA9, 0);		/* DRXD */
-	at91_set_A_periph(AT91_PIN_PA10, 1);		/* DTXD */
-}
-
-static struct resource uart0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_US0,
-		.end	= AT91SAM9261_BASE_US0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_US0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_US0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart0_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart0_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9261_uart0_device = {
-	.name		= "atmel_usart",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &uart0_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart0_data,
-	},
-	.resource	= uart0_resources,
-	.num_resources	= ARRAY_SIZE(uart0_resources),
-};
-
-static inline void configure_usart0_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PC8, 1);		/* TXD0 */
-	at91_set_A_periph(AT91_PIN_PC9, 0);		/* RXD0 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_A_periph(AT91_PIN_PC10, 0);	/* RTS0 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PC11, 0);	/* CTS0 */
-}
-
-static struct resource uart1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_US1,
-		.end	= AT91SAM9261_BASE_US1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_US1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_US1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart1_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart1_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9261_uart1_device = {
-	.name		= "atmel_usart",
-	.id		= 2,
-	.dev		= {
-				.dma_mask		= &uart1_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart1_data,
-	},
-	.resource	= uart1_resources,
-	.num_resources	= ARRAY_SIZE(uart1_resources),
-};
-
-static inline void configure_usart1_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PC12, 1);		/* TXD1 */
-	at91_set_A_periph(AT91_PIN_PC13, 0);		/* RXD1 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_B_periph(AT91_PIN_PA12, 0);	/* RTS1 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_B_periph(AT91_PIN_PA13, 0);	/* CTS1 */
-}
-
-static struct resource uart2_resources[] = {
-	[0] = {
-		.start	= AT91SAM9261_BASE_US2,
-		.end	= AT91SAM9261_BASE_US2 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9261_ID_US2,
-		.end	= NR_IRQS_LEGACY + AT91SAM9261_ID_US2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart2_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart2_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9261_uart2_device = {
-	.name		= "atmel_usart",
-	.id		= 3,
-	.dev		= {
-				.dma_mask		= &uart2_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart2_data,
-	},
-	.resource	= uart2_resources,
-	.num_resources	= ARRAY_SIZE(uart2_resources),
-};
-
-static inline void configure_usart2_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PC15, 0);		/* RXD2 */
-	at91_set_A_periph(AT91_PIN_PC14, 1);		/* TXD2 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_B_periph(AT91_PIN_PA15, 0);	/* RTS2*/
-	if (pins & ATMEL_UART_CTS)
-		at91_set_B_periph(AT91_PIN_PA16, 0);	/* CTS2 */
-}
-
-static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
-
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
-{
-	struct platform_device *pdev;
-	struct atmel_uart_data *pdata;
-
-	switch (id) {
-		case 0:		/* DBGU */
-			pdev = &at91sam9261_dbgu_device;
-			configure_dbgu_pins();
-			break;
-		case AT91SAM9261_ID_US0:
-			pdev = &at91sam9261_uart0_device;
-			configure_usart0_pins(pins);
-			break;
-		case AT91SAM9261_ID_US1:
-			pdev = &at91sam9261_uart1_device;
-			configure_usart1_pins(pins);
-			break;
-		case AT91SAM9261_ID_US2:
-			pdev = &at91sam9261_uart2_device;
-			configure_usart2_pins(pins);
-			break;
-		default:
-			return;
-	}
-	pdata = pdev->dev.platform_data;
-	pdata->num = portnr;		/* update to mapped ID */
-
-	if (portnr < ATMEL_MAX_UART)
-		at91_uarts[portnr] = pdev;
-}
-
-void __init at91_add_device_serial(void)
-{
-	int i;
-
-	for (i = 0; i < ATMEL_MAX_UART; i++) {
-		if (at91_uarts[i])
-			platform_device_register(at91_uarts[i]);
-	}
-}
-#else
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_add_device_serial(void) {}
-#endif
-
-
-/* -------------------------------------------------------------------- */
-
-/*
- * These devices are always present and don't need any board-specific
- * setup.
- */
-static int __init at91_add_standard_devices(void)
-{
-	at91_add_device_rtt();
-	at91_add_device_watchdog();
-	at91_add_device_tc();
-	return 0;
-}
-
-arch_initcall(at91_add_standard_devices);

arch/arm/mach-at91/at91sam9263.c

@@ -10,308 +10,11 @@
  *
  */
 
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk/at91_pmc.h>
-
-#include <asm/proc-fns.h>
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
 #include <asm/system_misc.h>
-#include <mach/at91sam9263.h>
 #include <mach/hardware.h>
 
-#include "at91_aic.h"
 #include "soc.h"
 #include "generic.h"
-#include "sam9_smc.h"
-#include "pm.h"
-
-#if defined(CONFIG_OLD_CLK_AT91)
-#include "clock.h"
-/* --------------------------------------------------------------------
- *  Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk pioA_clk = {
-	.name		= "pioA_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_PIOA,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioB_clk = {
-	.name		= "pioB_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_PIOB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioCDE_clk = {
-	.name		= "pioCDE_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_PIOCDE,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
-	.name		= "usart0_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_US0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
-	.name		= "usart1_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_US1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
-	.name		= "usart2_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_US2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc0_clk = {
-	.name		= "mci0_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_MCI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc1_clk = {
-	.name		= "mci1_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_MCI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk can_clk = {
-	.name		= "can_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_CAN,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi_clk = {
-	.name		= "twi_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_TWI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi0_clk = {
-	.name		= "spi0_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_SPI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi1_clk = {
-	.name		= "spi1_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_SPI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc0_clk = {
-	.name		= "ssc0_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_SSC0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc1_clk = {
-	.name		= "ssc1_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_SSC1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ac97_clk = {
-	.name		= "ac97_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_AC97C,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tcb_clk = {
-	.name		= "tcb_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_TCB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pwm_clk = {
-	.name		= "pwm_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_PWMC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk macb_clk = {
-	.name		= "pclk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_EMAC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk dma_clk = {
-	.name		= "dma_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_DMA,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twodge_clk = {
-	.name		= "2dge_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_2DGE,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk udc_clk = {
-	.name		= "udc_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_UDP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk isi_clk = {
-	.name		= "isi_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_ISI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk lcdc_clk = {
-	.name		= "lcdc_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_LCDC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ohci_clk = {
-	.name		= "ohci_clk",
-	.pmc_mask	= 1 << AT91SAM9263_ID_UHP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk *periph_clocks[] __initdata = {
-	&pioA_clk,
-	&pioB_clk,
-	&pioCDE_clk,
-	&usart0_clk,
-	&usart1_clk,
-	&usart2_clk,
-	&mmc0_clk,
-	&mmc1_clk,
-	&can_clk,
-	&twi_clk,
-	&spi0_clk,
-	&spi1_clk,
-	&ssc0_clk,
-	&ssc1_clk,
-	&ac97_clk,
-	&tcb_clk,
-	&pwm_clk,
-	&macb_clk,
-	&twodge_clk,
-	&udc_clk,
-	&isi_clk,
-	&lcdc_clk,
-	&dma_clk,
-	&ohci_clk,
-	// irq0 .. irq1
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
-	/* One additional fake clock for macb_hclk */
-	CLKDEV_CON_ID("hclk", &macb_clk),
-	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.0", &ssc0_clk),
-	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.1", &ssc1_clk),
-	CLKDEV_CON_DEV_ID("pclk", "fff98000.ssc", &ssc0_clk),
-	CLKDEV_CON_DEV_ID("pclk", "fff9c000.ssc", &ssc1_clk),
-	CLKDEV_CON_DEV_ID("hclk", "at91sam9263-lcdfb.0", &lcdc_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260.0", &twi_clk),
-	CLKDEV_CON_DEV_ID(NULL, "at91sam9rl-pwm", &pwm_clk),
-	CLKDEV_CON_DEV_ID(NULL, "rtc-at91sam9.0", &clk32k),
-	CLKDEV_CON_DEV_ID(NULL, "rtc-at91sam9.1", &clk32k),
-	/* fake hclk clock */
-	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
-	CLKDEV_CON_ID("pioA", &pioA_clk),
-	CLKDEV_CON_ID("pioB", &pioB_clk),
-	CLKDEV_CON_ID("pioC", &pioCDE_clk),
-	CLKDEV_CON_ID("pioD", &pioCDE_clk),
-	CLKDEV_CON_ID("pioE", &pioCDE_clk),
-	/* more usart lookup table for DT entries */
-	CLKDEV_CON_DEV_ID("usart", "ffffee00.serial", &mck),
-	CLKDEV_CON_DEV_ID("usart", "fff8c000.serial", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "fff90000.serial", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk),
-	/* more tc lookup table for DT entries */
-	CLKDEV_CON_DEV_ID("t0_clk", "fff7c000.timer", &tcb_clk),
-	CLKDEV_CON_DEV_ID("hclk", "a00000.ohci", &ohci_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "fffa4000.spi", &spi0_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "fffa8000.spi", &spi1_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "fff80000.mmc", &mmc0_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "fff84000.mmc", &mmc1_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fff88000.i2c", &twi_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioB_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioCDE_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCDE_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCDE_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffb8000.pwm", &pwm_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffffd20.rtc", &clk32k),
-	CLKDEV_CON_DEV_ID(NULL, "fffffd50.rtc", &clk32k),
-};
-
-static struct clk_lookup usart_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
-};
-
-/*
- * The four programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
-	.name		= "pck0",
-	.pmc_mask	= AT91_PMC_PCK0,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 0,
-};
-static struct clk pck1 = {
-	.name		= "pck1",
-	.pmc_mask	= AT91_PMC_PCK1,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 1,
-};
-static struct clk pck2 = {
-	.name		= "pck2",
-	.pmc_mask	= AT91_PMC_PCK2,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 2,
-};
-static struct clk pck3 = {
-	.name		= "pck3",
-	.pmc_mask	= AT91_PMC_PCK3,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 3,
-};
-
-static void __init at91sam9263_register_clocks(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
-		clk_register(periph_clocks[i]);
-
-	clkdev_add_table(periph_clocks_lookups,
-			 ARRAY_SIZE(periph_clocks_lookups));
-	clkdev_add_table(usart_clocks_lookups,
-			 ARRAY_SIZE(usart_clocks_lookups));
-
-	clk_register(&pck0);
-	clk_register(&pck1);
-	clk_register(&pck2);
-	clk_register(&pck3);
-}
-#else
-#define at91sam9263_register_clocks NULL
-#endif
-
-/* --------------------------------------------------------------------
- *  GPIO
- * -------------------------------------------------------------------- */
-
-static struct at91_gpio_bank at91sam9263_gpio[] __initdata = {
-	{
-		.id		= AT91SAM9263_ID_PIOA,
-		.regbase	= AT91SAM9263_BASE_PIOA,
-	}, {
-		.id		= AT91SAM9263_ID_PIOB,
-		.regbase	= AT91SAM9263_BASE_PIOB,
-	}, {
-		.id		= AT91SAM9263_ID_PIOCDE,
-		.regbase	= AT91SAM9263_BASE_PIOC,
-	}, {
-		.id		= AT91SAM9263_ID_PIOCDE,
-		.regbase	= AT91SAM9263_BASE_PIOD,
-	}, {
-		.id		= AT91SAM9263_ID_PIOCDE,
-		.regbase	= AT91SAM9263_BASE_PIOE,
-	}
-};
 
 /* --------------------------------------------------------------------
  *  AT91SAM9263 processor initialization
@@ -323,121 +26,15 @@ static void __init at91sam9263_map_io(void)
 	at91_init_sram(1, AT91SAM9263_SRAM1_BASE, AT91SAM9263_SRAM1_SIZE);
 }
 
-static void __init at91sam9263_ioremap_registers(void)
-{
-	at91_ioremap_ramc(0, AT91SAM9263_BASE_SDRAMC0, 512);
-	at91_ioremap_ramc(1, AT91SAM9263_BASE_SDRAMC1, 512);
-	at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT);
-	at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0);
-	at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
-	at91_ioremap_matrix(AT91SAM9263_BASE_MATRIX);
-	at91_pm_set_standby(at91sam9_sdram_standby);
-}
-
 static void __init at91sam9263_initialize(void)
 {
 	arm_pm_idle = at91sam9_idle;
 
 	at91_sysirq_mask_rtt(AT91SAM9263_BASE_RTT0);
 	at91_sysirq_mask_rtt(AT91SAM9263_BASE_RTT1);
-
-	/* Register GPIO subsystem */
-	at91_gpio_init(at91sam9263_gpio, 5);
-}
-
-static struct resource rstc_resources[] = {
-	[0] = {
-		.start  = AT91SAM9263_BASE_RSTC,
-		.end    = AT91SAM9263_BASE_RSTC + SZ_16 - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start  = AT91SAM9263_BASE_SDRAMC0,
-		.end    = AT91SAM9263_BASE_SDRAMC0 + SZ_512 - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device rstc_device = {
-	.name           = "at91-sam9260-reset",
-	.resource       = rstc_resources,
-	.num_resources  = ARRAY_SIZE(rstc_resources),
-};
-
-static struct resource shdwc_resources[] = {
-	[0] = {
-		.start  = AT91SAM9263_BASE_SHDWC,
-		.end    = AT91SAM9263_BASE_SHDWC + SZ_16 - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device shdwc_device = {
-	.name           = "at91-poweroff",
-	.resource       = shdwc_resources,
-	.num_resources  = ARRAY_SIZE(shdwc_resources),
-};
-
-static void __init at91sam9263_register_devices(void)
-{
-	platform_device_register(&rstc_device);
-	platform_device_register(&shdwc_device);
-}
-
-/* --------------------------------------------------------------------
- *  Interrupt initialization
- * -------------------------------------------------------------------- */
-
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
-	7,	/* Advanced Interrupt Controller (FIQ) */
-	7,	/* System Peripherals */
-	1,	/* Parallel IO Controller A */
-	1,	/* Parallel IO Controller B */
-	1,	/* Parallel IO Controller C, D and E */
-	0,
-	0,
-	5,	/* USART 0 */
-	5,	/* USART 1 */
-	5,	/* USART 2 */
-	0,	/* Multimedia Card Interface 0 */
-	0,	/* Multimedia Card Interface 1 */
-	3,	/* CAN */
-	6,	/* Two-Wire Interface */
-	5,	/* Serial Peripheral Interface 0 */
-	5,	/* Serial Peripheral Interface 1 */
-	4,	/* Serial Synchronous Controller 0 */
-	4,	/* Serial Synchronous Controller 1 */
-	5,	/* AC97 Controller */
-	0,	/* Timer Counter 0, 1 and 2 */
-	0,	/* Pulse Width Modulation Controller */
-	3,	/* Ethernet */
-	0,
-	0,	/* 2D Graphic Engine */
-	2,	/* USB Device Port */
-	0,	/* Image Sensor Interface */
-	3,	/* LDC Controller */
-	0,	/* DMA Controller */
-	0,
-	2,	/* USB Host port */
-	0,	/* Advanced Interrupt Controller (IRQ0) */
-	0,	/* Advanced Interrupt Controller (IRQ1) */
-};
-
-static void __init at91sam9263_init_time(void)
-{
-	at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
 }
 
 AT91_SOC_START(at91sam9263)
 	.map_io = at91sam9263_map_io,
-	.default_irq_priority = at91sam9263_default_irq_priority,
-	.extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1),
-	.ioremap_registers = at91sam9263_ioremap_registers,
-	.register_clocks = at91sam9263_register_clocks,
-	.register_devices = at91sam9263_register_devices,
 	.init = at91sam9263_initialize,
-	.init_time = at91sam9263_init_time,
 AT91_SOC_END

arch/arm/mach-at91/at91sam9263_devices.c

@@ -1,1538 +0,0 @@
-/*
- * arch/arm/mach-at91/at91sam9263_devices.c
- *
- *  Copyright (C) 2007 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/i2c-gpio.h>
-
-#include <linux/fb.h>
-#include <video/atmel_lcdc.h>
-
-#include <mach/at91sam9263.h>
-#include <mach/at91sam9263_matrix.h>
-#include <mach/at91_matrix.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/hardware.h>
-
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-/* --------------------------------------------------------------------
- *  USB Host
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-static struct at91_usbh_data usbh_data;
-
-static struct resource usbh_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_UHP_BASE,
-		.end	= AT91SAM9263_UHP_BASE + SZ_1M - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_UHP,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_UHP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91_usbh_device = {
-	.name		= "at91_ohci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &ohci_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &usbh_data,
-	},
-	.resource	= usbh_resources,
-	.num_resources	= ARRAY_SIZE(usbh_resources),
-};
-
-void __init at91_add_device_usbh(struct at91_usbh_data *data)
-{
-	int i;
-
-	if (!data)
-		return;
-
-	/* Enable VBus control for UHP ports */
-	for (i = 0; i < data->ports; i++) {
-		if (gpio_is_valid(data->vbus_pin[i]))
-			at91_set_gpio_output(data->vbus_pin[i],
-					     data->vbus_pin_active_low[i]);
-	}
-
-	/* Enable overcurrent notification */
-	for (i = 0; i < data->ports; i++) {
-		if (gpio_is_valid(data->overcurrent_pin[i]))
-			at91_set_gpio_input(data->overcurrent_pin[i], 1);
-	}
-
-	usbh_data = *data;
-	platform_device_register(&at91_usbh_device);
-}
-#else
-void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  USB Device (Gadget)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
-static struct at91_udc_data udc_data;
-
-static struct resource udc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_UDP,
-		.end	= AT91SAM9263_BASE_UDP + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_UDP,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_UDP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91_udc_device = {
-	.name		= "at91_udc",
-	.id		= -1,
-	.dev		= {
-				.platform_data		= &udc_data,
-	},
-	.resource	= udc_resources,
-	.num_resources	= ARRAY_SIZE(udc_resources),
-};
-
-void __init at91_add_device_udc(struct at91_udc_data *data)
-{
-	if (!data)
-		return;
-
-	if (gpio_is_valid(data->vbus_pin)) {
-		at91_set_gpio_input(data->vbus_pin, 0);
-		at91_set_deglitch(data->vbus_pin, 1);
-	}
-
-	/* Pullup pin is handled internally by USB device peripheral */
-
-	udc_data = *data;
-	platform_device_register(&at91_udc_device);
-}
-#else
-void __init at91_add_device_udc(struct at91_udc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Ethernet
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
-static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct macb_platform_data eth_data;
-
-static struct resource eth_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_EMAC,
-		.end	= AT91SAM9263_BASE_EMAC + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_EMAC,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_EMAC,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_eth_device = {
-	.name		= "macb",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &eth_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &eth_data,
-	},
-	.resource	= eth_resources,
-	.num_resources	= ARRAY_SIZE(eth_resources),
-};
-
-void __init at91_add_device_eth(struct macb_platform_data *data)
-{
-	if (!data)
-		return;
-
-	if (gpio_is_valid(data->phy_irq_pin)) {
-		at91_set_gpio_input(data->phy_irq_pin, 0);
-		at91_set_deglitch(data->phy_irq_pin, 1);
-	}
-
-	/* Pins used for MII and RMII */
-	at91_set_A_periph(AT91_PIN_PE21, 0);	/* ETXCK_EREFCK */
-	at91_set_B_periph(AT91_PIN_PC25, 0);	/* ERXDV */
-	at91_set_A_periph(AT91_PIN_PE25, 0);	/* ERX0 */
-	at91_set_A_periph(AT91_PIN_PE26, 0);	/* ERX1 */
-	at91_set_A_periph(AT91_PIN_PE27, 0);	/* ERXER */
-	at91_set_A_periph(AT91_PIN_PE28, 0);	/* ETXEN */
-	at91_set_A_periph(AT91_PIN_PE23, 0);	/* ETX0 */
-	at91_set_A_periph(AT91_PIN_PE24, 0);	/* ETX1 */
-	at91_set_A_periph(AT91_PIN_PE30, 0);	/* EMDIO */
-	at91_set_A_periph(AT91_PIN_PE29, 0);	/* EMDC */
-
-	if (!data->is_rmii) {
-		at91_set_A_periph(AT91_PIN_PE22, 0);	/* ECRS */
-		at91_set_B_periph(AT91_PIN_PC26, 0);	/* ECOL */
-		at91_set_B_periph(AT91_PIN_PC22, 0);	/* ERX2 */
-		at91_set_B_periph(AT91_PIN_PC23, 0);	/* ERX3 */
-		at91_set_B_periph(AT91_PIN_PC27, 0);	/* ERXCK */
-		at91_set_B_periph(AT91_PIN_PC20, 0);	/* ETX2 */
-		at91_set_B_periph(AT91_PIN_PC21, 0);	/* ETX3 */
-		at91_set_B_periph(AT91_PIN_PC24, 0);	/* ETXER */
-	}
-
-	eth_data = *data;
-	platform_device_register(&at91sam9263_eth_device);
-}
-#else
-void __init at91_add_device_eth(struct macb_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  MMC / SD
- * -------------------------------------------------------------------- */
-
-#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct mci_platform_data mmc0_data, mmc1_data;
-
-static struct resource mmc0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_MCI0,
-		.end	= AT91SAM9263_BASE_MCI0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_MCI0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_MCI0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_mmc0_device = {
-	.name		= "atmel_mci",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &mmc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &mmc0_data,
-	},
-	.resource	= mmc0_resources,
-	.num_resources	= ARRAY_SIZE(mmc0_resources),
-};
-
-static struct resource mmc1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_MCI1,
-		.end	= AT91SAM9263_BASE_MCI1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_MCI1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_MCI1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_mmc1_device = {
-	.name		= "atmel_mci",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &mmc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &mmc1_data,
-	},
-	.resource	= mmc1_resources,
-	.num_resources	= ARRAY_SIZE(mmc1_resources),
-};
-
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
-{
-	unsigned int i;
-	unsigned int slot_count = 0;
-
-	if (!data)
-		return;
-
-	for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
-
-		if (!data->slot[i].bus_width)
-			continue;
-
-		/* input/irq */
-		if (gpio_is_valid(data->slot[i].detect_pin)) {
-			at91_set_gpio_input(data->slot[i].detect_pin,
-					1);
-			at91_set_deglitch(data->slot[i].detect_pin,
-					1);
-		}
-		if (gpio_is_valid(data->slot[i].wp_pin))
-			at91_set_gpio_input(data->slot[i].wp_pin, 1);
-
-		if (mmc_id == 0) {				/* MCI0 */
-			switch (i) {
-			case 0:					/* slot A */
-				/* CMD */
-				at91_set_A_periph(AT91_PIN_PA1, 1);
-				/* DAT0, maybe DAT1..DAT3 */
-				at91_set_A_periph(AT91_PIN_PA0, 1);
-				if (data->slot[i].bus_width == 4) {
-					at91_set_A_periph(AT91_PIN_PA3, 1);
-					at91_set_A_periph(AT91_PIN_PA4, 1);
-					at91_set_A_periph(AT91_PIN_PA5, 1);
-				}
-				slot_count++;
-				break;
-			case 1:					/* slot B */
-				/* CMD */
-				at91_set_A_periph(AT91_PIN_PA16, 1);
-				/* DAT0, maybe DAT1..DAT3 */
-				at91_set_A_periph(AT91_PIN_PA17, 1);
-				if (data->slot[i].bus_width == 4) {
-					at91_set_A_periph(AT91_PIN_PA18, 1);
-					at91_set_A_periph(AT91_PIN_PA19, 1);
-					at91_set_A_periph(AT91_PIN_PA20, 1);
-				}
-				slot_count++;
-				break;
-			default:
-				printk(KERN_ERR
-				       "AT91: SD/MMC slot %d not available\n", i);
-				break;
-			}
-			if (slot_count) {
-				/* CLK */
-				at91_set_A_periph(AT91_PIN_PA12, 0);
-
-				mmc0_data = *data;
-				platform_device_register(&at91sam9263_mmc0_device);
-			}
-		} else if (mmc_id == 1) {			/* MCI1 */
-			switch (i) {
-			case 0:					/* slot A */
-				/* CMD */
-				at91_set_A_periph(AT91_PIN_PA7, 1);
-				/* DAT0, maybe DAT1..DAT3 */
-				at91_set_A_periph(AT91_PIN_PA8, 1);
-				if (data->slot[i].bus_width == 4) {
-					at91_set_A_periph(AT91_PIN_PA9, 1);
-					at91_set_A_periph(AT91_PIN_PA10, 1);
-					at91_set_A_periph(AT91_PIN_PA11, 1);
-				}
-				slot_count++;
-				break;
-			case 1:					/* slot B */
-				/* CMD */
-				at91_set_A_periph(AT91_PIN_PA21, 1);
-				/* DAT0, maybe DAT1..DAT3 */
-				at91_set_A_periph(AT91_PIN_PA22, 1);
-				if (data->slot[i].bus_width == 4) {
-					at91_set_A_periph(AT91_PIN_PA23, 1);
-					at91_set_A_periph(AT91_PIN_PA24, 1);
-					at91_set_A_periph(AT91_PIN_PA25, 1);
-				}
-				slot_count++;
-				break;
-			default:
-				printk(KERN_ERR
-				       "AT91: SD/MMC slot %d not available\n", i);
-				break;
-			}
-			if (slot_count) {
-				/* CLK */
-				at91_set_A_periph(AT91_PIN_PA6, 0);
-
-				mmc1_data = *data;
-				platform_device_register(&at91sam9263_mmc1_device);
-			}
-		}
-	}
-}
-#else
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- *  Compact Flash (PCMCIA or IDE)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
-	defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
-
-static struct at91_cf_data cf0_data;
-
-static struct resource cf0_resources[] = {
-	[0] = {
-		.start	= AT91_CHIPSELECT_4,
-		.end	= AT91_CHIPSELECT_4 + SZ_256M - 1,
-		.flags	= IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
-	}
-};
-
-static struct platform_device cf0_device = {
-	.id		= 0,
-	.dev		= {
-				.platform_data	= &cf0_data,
-	},
-	.resource	= cf0_resources,
-	.num_resources	= ARRAY_SIZE(cf0_resources),
-};
-
-static struct at91_cf_data cf1_data;
-
-static struct resource cf1_resources[] = {
-	[0] = {
-		.start	= AT91_CHIPSELECT_5,
-		.end	= AT91_CHIPSELECT_5 + SZ_256M - 1,
-		.flags	= IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
-	}
-};
-
-static struct platform_device cf1_device = {
-	.id		= 1,
-	.dev		= {
-				.platform_data	= &cf1_data,
-	},
-	.resource	= cf1_resources,
-	.num_resources	= ARRAY_SIZE(cf1_resources),
-};
-
-void __init at91_add_device_cf(struct at91_cf_data *data)
-{
-	unsigned long ebi0_csa;
-	struct platform_device *pdev;
-
-	if (!data)
-		return;
-
-	/*
-	 * assign CS4 or CS5 to SMC with Compact Flash logic support,
-	 * we assume SMC timings are configured by board code,
-	 * except True IDE where timings are controlled by driver
-	 */
-	ebi0_csa = at91_matrix_read(AT91_MATRIX_EBI0CSA);
-	switch (data->chipselect) {
-	case 4:
-		at91_set_A_periph(AT91_PIN_PD6, 0);  /* EBI0_NCS4/CFCS0 */
-		ebi0_csa |= AT91_MATRIX_EBI0_CS4A_SMC_CF1;
-		cf0_data = *data;
-		pdev = &cf0_device;
-		break;
-	case 5:
-		at91_set_A_periph(AT91_PIN_PD7, 0);  /* EBI0_NCS5/CFCS1 */
-		ebi0_csa |= AT91_MATRIX_EBI0_CS5A_SMC_CF2;
-		cf1_data = *data;
-		pdev = &cf1_device;
-		break;
-	default:
-		printk(KERN_ERR "AT91 CF: bad chip-select requested (%u)\n",
-		       data->chipselect);
-		return;
-	}
-	at91_matrix_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
-
-	if (gpio_is_valid(data->det_pin)) {
-		at91_set_gpio_input(data->det_pin, 1);
-		at91_set_deglitch(data->det_pin, 1);
-	}
-
-	if (gpio_is_valid(data->irq_pin)) {
-		at91_set_gpio_input(data->irq_pin, 1);
-		at91_set_deglitch(data->irq_pin, 1);
-	}
-
-	if (gpio_is_valid(data->vcc_pin))
-		/* initially off */
-		at91_set_gpio_output(data->vcc_pin, 0);
-
-	/* enable EBI controlled pins */
-	at91_set_A_periph(AT91_PIN_PD5, 1);  /* NWAIT */
-	at91_set_A_periph(AT91_PIN_PD8, 0);  /* CFCE1 */
-	at91_set_A_periph(AT91_PIN_PD9, 0);  /* CFCE2 */
-	at91_set_A_periph(AT91_PIN_PD14, 0); /* CFNRW */
-
-	pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "pata_at91" : "at91_cf";
-	platform_device_register(pdev);
-}
-#else
-void __init at91_add_device_cf(struct at91_cf_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- *  NAND / SmartMedia
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
-static struct atmel_nand_data nand_data;
-
-#define NAND_BASE	AT91_CHIPSELECT_3
-
-static struct resource nand_resources[] = {
-	[0] = {
-		.start	= NAND_BASE,
-		.end	= NAND_BASE + SZ_256M - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT91SAM9263_BASE_ECC0,
-		.end	= AT91SAM9263_BASE_ECC0 + SZ_512 - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device at91sam9263_nand_device = {
-	.name		= "atmel_nand",
-	.id		= -1,
-	.dev		= {
-				.platform_data	= &nand_data,
-	},
-	.resource	= nand_resources,
-	.num_resources	= ARRAY_SIZE(nand_resources),
-};
-
-void __init at91_add_device_nand(struct atmel_nand_data *data)
-{
-	unsigned long csa;
-
-	if (!data)
-		return;
-
-	csa = at91_matrix_read(AT91_MATRIX_EBI0CSA);
-	at91_matrix_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
-
-	/* enable pin */
-	if (gpio_is_valid(data->enable_pin))
-		at91_set_gpio_output(data->enable_pin, 1);
-
-	/* ready/busy pin */
-	if (gpio_is_valid(data->rdy_pin))
-		at91_set_gpio_input(data->rdy_pin, 1);
-
-	/* card detect pin */
-	if (gpio_is_valid(data->det_pin))
-		at91_set_gpio_input(data->det_pin, 1);
-
-	nand_data = *data;
-	platform_device_register(&at91sam9263_nand_device);
-}
-#else
-void __init at91_add_device_nand(struct atmel_nand_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  TWI (i2c)
- * -------------------------------------------------------------------- */
-
-/*
- * Prefer the GPIO code since the TWI controller isn't robust
- * (gets overruns and underruns under load) and can only issue
- * repeated STARTs in one scenario (the driver doesn't yet handle them).
- */
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
-
-static struct i2c_gpio_platform_data pdata = {
-	.sda_pin		= AT91_PIN_PB4,
-	.sda_is_open_drain	= 1,
-	.scl_pin		= AT91_PIN_PB5,
-	.scl_is_open_drain	= 1,
-	.udelay			= 2,		/* ~100 kHz */
-};
-
-static struct platform_device at91sam9263_twi_device = {
-	.name			= "i2c-gpio",
-	.id			= 0,
-	.dev.platform_data	= &pdata,
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	at91_set_GPIO_periph(AT91_PIN_PB4, 1);		/* TWD (SDA) */
-	at91_set_multi_drive(AT91_PIN_PB4, 1);
-
-	at91_set_GPIO_periph(AT91_PIN_PB5, 1);		/* TWCK (SCL) */
-	at91_set_multi_drive(AT91_PIN_PB5, 1);
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at91sam9263_twi_device);
-}
-
-#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
-
-static struct resource twi_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_TWI,
-		.end	= AT91SAM9263_BASE_TWI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_TWI,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_TWI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_twi_device = {
-	.name		= "i2c-at91sam9260",
-	.id		= 0,
-	.resource	= twi_resources,
-	.num_resources	= ARRAY_SIZE(twi_resources),
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	/* pins used for TWI interface */
-	at91_set_A_periph(AT91_PIN_PB4, 0);		/* TWD */
-	at91_set_multi_drive(AT91_PIN_PB4, 1);
-
-	at91_set_A_periph(AT91_PIN_PB5, 0);		/* TWCK */
-	at91_set_multi_drive(AT91_PIN_PB5, 1);
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at91sam9263_twi_device);
-}
-#else
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  SPI
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct resource spi0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_SPI0,
-		.end	= AT91SAM9263_BASE_SPI0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_SPI0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_SPI0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_spi0_device = {
-	.name		= "atmel_spi",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &spi_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= spi0_resources,
-	.num_resources	= ARRAY_SIZE(spi0_resources),
-};
-
-static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA5, AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PB11 };
-
-static struct resource spi1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_SPI1,
-		.end	= AT91SAM9263_BASE_SPI1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_SPI1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_SPI1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_spi1_device = {
-	.name		= "atmel_spi",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &spi_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= spi1_resources,
-	.num_resources	= ARRAY_SIZE(spi1_resources),
-};
-
-static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB15, AT91_PIN_PB16, AT91_PIN_PB17, AT91_PIN_PB18 };
-
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
-{
-	int i;
-	unsigned long cs_pin;
-	short enable_spi0 = 0;
-	short enable_spi1 = 0;
-
-	/* Choose SPI chip-selects */
-	for (i = 0; i < nr_devices; i++) {
-		if (devices[i].controller_data)
-			cs_pin = (unsigned long) devices[i].controller_data;
-		else if (devices[i].bus_num == 0)
-			cs_pin = spi0_standard_cs[devices[i].chip_select];
-		else
-			cs_pin = spi1_standard_cs[devices[i].chip_select];
-
-		if (!gpio_is_valid(cs_pin))
-			continue;
-
-		if (devices[i].bus_num == 0)
-			enable_spi0 = 1;
-		else
-			enable_spi1 = 1;
-
-		/* enable chip-select pin */
-		at91_set_gpio_output(cs_pin, 1);
-
-		/* pass chip-select pin to driver */
-		devices[i].controller_data = (void *) cs_pin;
-	}
-
-	spi_register_board_info(devices, nr_devices);
-
-	/* Configure SPI bus(es) */
-	if (enable_spi0) {
-		at91_set_B_periph(AT91_PIN_PA0, 0);	/* SPI0_MISO */
-		at91_set_B_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
-		at91_set_B_periph(AT91_PIN_PA2, 0);	/* SPI0_SPCK */
-
-		platform_device_register(&at91sam9263_spi0_device);
-	}
-	if (enable_spi1) {
-		at91_set_A_periph(AT91_PIN_PB12, 0);	/* SPI1_MISO */
-		at91_set_A_periph(AT91_PIN_PB13, 0);	/* SPI1_MOSI */
-		at91_set_A_periph(AT91_PIN_PB14, 0);	/* SPI1_SPCK */
-
-		platform_device_register(&at91sam9263_spi1_device);
-	}
-}
-#else
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  AC97
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
-static u64 ac97_dmamask = DMA_BIT_MASK(32);
-static struct ac97c_platform_data ac97_data;
-
-static struct resource ac97_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_AC97C,
-		.end	= AT91SAM9263_BASE_AC97C + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_AC97C,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_AC97C,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_ac97_device = {
-	.name		= "atmel_ac97c",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &ac97_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &ac97_data,
-	},
-	.resource	= ac97_resources,
-	.num_resources	= ARRAY_SIZE(ac97_resources),
-};
-
-void __init at91_add_device_ac97(struct ac97c_platform_data *data)
-{
-	if (!data)
-		return;
-
-	at91_set_A_periph(AT91_PIN_PB0, 0);	/* AC97FS */
-	at91_set_A_periph(AT91_PIN_PB1, 0);	/* AC97CK */
-	at91_set_A_periph(AT91_PIN_PB2, 0);	/* AC97TX */
-	at91_set_A_periph(AT91_PIN_PB3, 0);	/* AC97RX */
-
-	/* reset */
-	if (gpio_is_valid(data->reset_pin))
-		at91_set_gpio_output(data->reset_pin, 0);
-
-	ac97_data = *data;
-	platform_device_register(&at91sam9263_ac97_device);
-}
-#else
-void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- *  CAN Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_CAN_AT91) || defined(CONFIG_CAN_AT91_MODULE)
-static struct resource can_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_CAN,
-		.end	= AT91SAM9263_BASE_CAN + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_CAN,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_CAN,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_can_device = {
-	.name		= "at91_can",
-	.id		= -1,
-	.resource	= can_resources,
-	.num_resources	= ARRAY_SIZE(can_resources),
-};
-
-void __init at91_add_device_can(struct at91_can_data *data)
-{
-	at91_set_A_periph(AT91_PIN_PA13, 0);	/* CANTX */
-	at91_set_A_periph(AT91_PIN_PA14, 0);	/* CANRX */
-	at91sam9263_can_device.dev.platform_data = data;
-
-	platform_device_register(&at91sam9263_can_device);
-}
-#else
-void __init at91_add_device_can(struct at91_can_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- *  LCD Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_pdata lcdc_data;
-
-static struct resource lcdc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_LCDC_BASE,
-		.end	= AT91SAM9263_LCDC_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_LCDC,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_LCDC,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91_lcdc_device = {
-	.name		= "at91sam9263-lcdfb",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &lcdc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &lcdc_data,
-	},
-	.resource	= lcdc_resources,
-	.num_resources	= ARRAY_SIZE(lcdc_resources),
-};
-
-void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
-{
-	if (!data)
-		return;
-
-	at91_set_A_periph(AT91_PIN_PC1, 0);	/* LCDHSYNC */
-	at91_set_A_periph(AT91_PIN_PC2, 0);	/* LCDDOTCK */
-	at91_set_A_periph(AT91_PIN_PC3, 0);	/* LCDDEN */
-	at91_set_B_periph(AT91_PIN_PB9, 0);	/* LCDCC */
-	at91_set_A_periph(AT91_PIN_PC6, 0);	/* LCDD2 */
-	at91_set_A_periph(AT91_PIN_PC7, 0);	/* LCDD3 */
-	at91_set_A_periph(AT91_PIN_PC8, 0);	/* LCDD4 */
-	at91_set_A_periph(AT91_PIN_PC9, 0);	/* LCDD5 */
-	at91_set_A_periph(AT91_PIN_PC10, 0);	/* LCDD6 */
-	at91_set_A_periph(AT91_PIN_PC11, 0);	/* LCDD7 */
-	at91_set_A_periph(AT91_PIN_PC14, 0);	/* LCDD10 */
-	at91_set_A_periph(AT91_PIN_PC15, 0);	/* LCDD11 */
-	at91_set_A_periph(AT91_PIN_PC16, 0);	/* LCDD12 */
-	at91_set_B_periph(AT91_PIN_PC12, 0);	/* LCDD13 */
-	at91_set_A_periph(AT91_PIN_PC18, 0);	/* LCDD14 */
-	at91_set_A_periph(AT91_PIN_PC19, 0);	/* LCDD15 */
-	at91_set_A_periph(AT91_PIN_PC22, 0);	/* LCDD18 */
-	at91_set_A_periph(AT91_PIN_PC23, 0);	/* LCDD19 */
-	at91_set_A_periph(AT91_PIN_PC24, 0);	/* LCDD20 */
-	at91_set_B_periph(AT91_PIN_PC17, 0);	/* LCDD21 */
-	at91_set_A_periph(AT91_PIN_PC26, 0);	/* LCDD22 */
-	at91_set_A_periph(AT91_PIN_PC27, 0);	/* LCDD23 */
-
-	lcdc_data = *data;
-	platform_device_register(&at91_lcdc_device);
-}
-#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Image Sensor Interface
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_VIDEO_AT91_ISI) || defined(CONFIG_VIDEO_AT91_ISI_MODULE)
-
-struct resource isi_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_ISI,
-		.end	= AT91SAM9263_BASE_ISI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_ISI,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_ISI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_isi_device = {
-	.name		= "at91_isi",
-	.id		= -1,
-	.resource	= isi_resources,
-	.num_resources	= ARRAY_SIZE(isi_resources),
-};
-
-void __init at91_add_device_isi(struct isi_platform_data *data,
-		bool use_pck_as_mck)
-{
-	at91_set_A_periph(AT91_PIN_PE0, 0);	/* ISI_D0 */
-	at91_set_A_periph(AT91_PIN_PE1, 0);	/* ISI_D1 */
-	at91_set_A_periph(AT91_PIN_PE2, 0);	/* ISI_D2 */
-	at91_set_A_periph(AT91_PIN_PE3, 0);	/* ISI_D3 */
-	at91_set_A_periph(AT91_PIN_PE4, 0);	/* ISI_D4 */
-	at91_set_A_periph(AT91_PIN_PE5, 0);	/* ISI_D5 */
-	at91_set_A_periph(AT91_PIN_PE6, 0);	/* ISI_D6 */
-	at91_set_A_periph(AT91_PIN_PE7, 0);	/* ISI_D7 */
-	at91_set_A_periph(AT91_PIN_PE8, 0);	/* ISI_PCK */
-	at91_set_A_periph(AT91_PIN_PE9, 0);	/* ISI_HSYNC */
-	at91_set_A_periph(AT91_PIN_PE10, 0);	/* ISI_VSYNC */
-	at91_set_B_periph(AT91_PIN_PE12, 0);	/* ISI_PD8 */
-	at91_set_B_periph(AT91_PIN_PE13, 0);	/* ISI_PD9 */
-	at91_set_B_periph(AT91_PIN_PE14, 0);	/* ISI_PD10 */
-	at91_set_B_periph(AT91_PIN_PE15, 0);	/* ISI_PD11 */
-
-	if (use_pck_as_mck) {
-		at91_set_B_periph(AT91_PIN_PE11, 0);	/* ISI_MCK (PCK3) */
-
-		/* TODO: register the PCK for ISI_MCK and set its parent */
-	}
-}
-#else
-void __init at91_add_device_isi(struct isi_platform_data *data,
-		bool use_pck_as_mck) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Timer/Counter block
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_ATMEL_TCLIB
-
-static struct resource tcb_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_TCB0,
-		.end	= AT91SAM9263_BASE_TCB0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_TCB,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_TCB,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_tcb_device = {
-	.name		= "atmel_tcb",
-	.id		= 0,
-	.resource	= tcb_resources,
-	.num_resources	= ARRAY_SIZE(tcb_resources),
-};
-
-#if defined(CONFIG_OF)
-static struct of_device_id tcb_ids[] = {
-	{ .compatible = "atmel,at91rm9200-tcb" },
-	{ /*sentinel*/ }
-};
-#endif
-
-static void __init at91_add_device_tc(void)
-{
-#if defined(CONFIG_OF)
-	struct device_node *np;
-
-	np = of_find_matching_node(NULL, tcb_ids);
-	if (np) {
-		of_node_put(np);
-		return;
-	}
-#endif
-
-	platform_device_register(&at91sam9263_tcb_device);
-}
-#else
-static void __init at91_add_device_tc(void) { }
-#endif
-
-
-/* --------------------------------------------------------------------
- *  RTT
- * -------------------------------------------------------------------- */
-
-static struct resource rtt0_resources[] = {
-	{
-		.start	= AT91SAM9263_BASE_RTT0,
-		.end	= AT91SAM9263_BASE_RTT0 + SZ_16 - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.flags  = IORESOURCE_IRQ,
-	}
-};
-
-static struct platform_device at91sam9263_rtt0_device = {
-	.name		= "at91_rtt",
-	.id		= 0,
-	.resource	= rtt0_resources,
-};
-
-static struct resource rtt1_resources[] = {
-	{
-		.start	= AT91SAM9263_BASE_RTT1,
-		.end	= AT91SAM9263_BASE_RTT1 + SZ_16 - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.flags  = IORESOURCE_IRQ,
-	}
-};
-
-static struct platform_device at91sam9263_rtt1_device = {
-	.name		= "at91_rtt",
-	.id		= 1,
-	.resource	= rtt1_resources,
-};
-
-#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
-static void __init at91_add_device_rtt_rtc(void)
-{
-	struct platform_device *pdev;
-	struct resource *r;
-
-	switch (CONFIG_RTC_DRV_AT91SAM9_RTT) {
-	case 0:
-		/*
-		 * The second resource is needed only for the chosen RTT:
-		 * GPBR will serve as the storage for RTC time offset
-		 */
-		at91sam9263_rtt0_device.num_resources = 3;
-		at91sam9263_rtt1_device.num_resources = 1;
-		pdev = &at91sam9263_rtt0_device;
-		r = rtt0_resources;
-		break;
-	case 1:
-		at91sam9263_rtt0_device.num_resources = 1;
-		at91sam9263_rtt1_device.num_resources = 3;
-		pdev = &at91sam9263_rtt1_device;
-		r = rtt1_resources;
-		break;
-	default:
-		pr_err("at91sam9263: only supports 2 RTT (%d)\n",
-		       CONFIG_RTC_DRV_AT91SAM9_RTT);
-		return;
-	}
-
-	pdev->name = "rtc-at91sam9";
-	r[1].start = AT91SAM9263_BASE_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
-	r[1].end = r[1].start + 3;
-	r[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
-	r[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
-}
-#else
-static void __init at91_add_device_rtt_rtc(void)
-{
-	/* Only one resource is needed: RTT not used as RTC */
-	at91sam9263_rtt0_device.num_resources = 1;
-	at91sam9263_rtt1_device.num_resources = 1;
-}
-#endif
-
-static void __init at91_add_device_rtt(void)
-{
-	at91_add_device_rtt_rtc();
-	platform_device_register(&at91sam9263_rtt0_device);
-	platform_device_register(&at91sam9263_rtt1_device);
-}
-
-
-/* --------------------------------------------------------------------
- *  Watchdog
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
-static struct resource wdt_resources[] = {
-	{
-		.start	= AT91SAM9263_BASE_WDT,
-		.end	= AT91SAM9263_BASE_WDT + SZ_16 - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device at91sam9263_wdt_device = {
-	.name		= "at91_wdt",
-	.id		= -1,
-	.resource	= wdt_resources,
-	.num_resources	= ARRAY_SIZE(wdt_resources),
-};
-
-static void __init at91_add_device_watchdog(void)
-{
-	platform_device_register(&at91sam9263_wdt_device);
-}
-#else
-static void __init at91_add_device_watchdog(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  PWM
- * --------------------------------------------------------------------*/
-
-#if IS_ENABLED(CONFIG_PWM_ATMEL)
-static struct resource pwm_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_PWMC,
-		.end	= AT91SAM9263_BASE_PWMC + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_PWMC,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_PWMC,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_pwm0_device = {
-	.name	= "at91sam9rl-pwm",
-	.id	= -1,
-	.resource	= pwm_resources,
-	.num_resources	= ARRAY_SIZE(pwm_resources),
-};
-
-void __init at91_add_device_pwm(u32 mask)
-{
-	if (mask & (1 << AT91_PWM0))
-		at91_set_B_periph(AT91_PIN_PB7, 1);	/* enable PWM0 */
-
-	if (mask & (1 << AT91_PWM1))
-		at91_set_B_periph(AT91_PIN_PB8, 1);	/* enable PWM1 */
-
-	if (mask & (1 << AT91_PWM2))
-		at91_set_B_periph(AT91_PIN_PC29, 1);	/* enable PWM2 */
-
-	if (mask & (1 << AT91_PWM3))
-		at91_set_B_periph(AT91_PIN_PB29, 1);	/* enable PWM3 */
-
-	platform_device_register(&at91sam9263_pwm0_device);
-}
-#else
-void __init at91_add_device_pwm(u32 mask) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  SSC -- Synchronous Serial Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
-static u64 ssc0_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_SSC0,
-		.end	= AT91SAM9263_BASE_SSC0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_SSC0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_SSC0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_ssc0_device = {
-	.name	= "at91rm9200_ssc",
-	.id	= 0,
-	.dev	= {
-		.dma_mask		= &ssc0_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= ssc0_resources,
-	.num_resources	= ARRAY_SIZE(ssc0_resources),
-};
-
-static inline void configure_ssc0_pins(unsigned pins)
-{
-	if (pins & ATMEL_SSC_TF)
-		at91_set_B_periph(AT91_PIN_PB0, 1);
-	if (pins & ATMEL_SSC_TK)
-		at91_set_B_periph(AT91_PIN_PB1, 1);
-	if (pins & ATMEL_SSC_TD)
-		at91_set_B_periph(AT91_PIN_PB2, 1);
-	if (pins & ATMEL_SSC_RD)
-		at91_set_B_periph(AT91_PIN_PB3, 1);
-	if (pins & ATMEL_SSC_RK)
-		at91_set_B_periph(AT91_PIN_PB4, 1);
-	if (pins & ATMEL_SSC_RF)
-		at91_set_B_periph(AT91_PIN_PB5, 1);
-}
-
-static u64 ssc1_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_SSC1,
-		.end	= AT91SAM9263_BASE_SSC1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_SSC1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_SSC1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9263_ssc1_device = {
-	.name	= "at91rm9200_ssc",
-	.id	= 1,
-	.dev	= {
-		.dma_mask		= &ssc1_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= ssc1_resources,
-	.num_resources	= ARRAY_SIZE(ssc1_resources),
-};
-
-static inline void configure_ssc1_pins(unsigned pins)
-{
-	if (pins & ATMEL_SSC_TF)
-		at91_set_A_periph(AT91_PIN_PB6, 1);
-	if (pins & ATMEL_SSC_TK)
-		at91_set_A_periph(AT91_PIN_PB7, 1);
-	if (pins & ATMEL_SSC_TD)
-		at91_set_A_periph(AT91_PIN_PB8, 1);
-	if (pins & ATMEL_SSC_RD)
-		at91_set_A_periph(AT91_PIN_PB9, 1);
-	if (pins & ATMEL_SSC_RK)
-		at91_set_A_periph(AT91_PIN_PB10, 1);
-	if (pins & ATMEL_SSC_RF)
-		at91_set_A_periph(AT91_PIN_PB11, 1);
-}
-
-/*
- * SSC controllers are accessed through library code, instead of any
- * kind of all-singing/all-dancing driver.  For example one could be
- * used by a particular I2S audio codec's driver, while another one
- * on the same system might be used by a custom data capture driver.
- */
-void __init at91_add_device_ssc(unsigned id, unsigned pins)
-{
-	struct platform_device *pdev;
-
-	/*
-	 * NOTE: caller is responsible for passing information matching
-	 * "pins" to whatever will be using each particular controller.
-	 */
-	switch (id) {
-	case AT91SAM9263_ID_SSC0:
-		pdev = &at91sam9263_ssc0_device;
-		configure_ssc0_pins(pins);
-		break;
-	case AT91SAM9263_ID_SSC1:
-		pdev = &at91sam9263_ssc1_device;
-		configure_ssc1_pins(pins);
-		break;
-	default:
-		return;
-	}
-
-	platform_device_register(pdev);
-}
-
-#else
-void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  UART
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SERIAL_ATMEL)
-
-static struct resource dbgu_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_DBGU,
-		.end	= AT91SAM9263_BASE_DBGU + SZ_512 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.end	= NR_IRQS_LEGACY + AT91_ID_SYS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data dbgu_data = {
-	.use_dma_tx	= 0,
-	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
-};
-
-static u64 dbgu_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_dbgu_device = {
-	.name		= "atmel_usart",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &dbgu_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &dbgu_data,
-	},
-	.resource	= dbgu_resources,
-	.num_resources	= ARRAY_SIZE(dbgu_resources),
-};
-
-static inline void configure_dbgu_pins(void)
-{
-	at91_set_A_periph(AT91_PIN_PC30, 0);		/* DRXD */
-	at91_set_A_periph(AT91_PIN_PC31, 1);		/* DTXD */
-}
-
-static struct resource uart0_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_US0,
-		.end	= AT91SAM9263_BASE_US0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_US0,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_US0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart0_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart0_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_uart0_device = {
-	.name		= "atmel_usart",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &uart0_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart0_data,
-	},
-	.resource	= uart0_resources,
-	.num_resources	= ARRAY_SIZE(uart0_resources),
-};
-
-static inline void configure_usart0_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PA26, 1);		/* TXD0 */
-	at91_set_A_periph(AT91_PIN_PA27, 0);		/* RXD0 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_A_periph(AT91_PIN_PA28, 0);	/* RTS0 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PA29, 0);	/* CTS0 */
-}
-
-static struct resource uart1_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_US1,
-		.end	= AT91SAM9263_BASE_US1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_US1,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_US1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart1_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart1_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_uart1_device = {
-	.name		= "atmel_usart",
-	.id		= 2,
-	.dev		= {
-				.dma_mask		= &uart1_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart1_data,
-	},
-	.resource	= uart1_resources,
-	.num_resources	= ARRAY_SIZE(uart1_resources),
-};
-
-static inline void configure_usart1_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PD0, 1);		/* TXD1 */
-	at91_set_A_periph(AT91_PIN_PD1, 0);		/* RXD1 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_B_periph(AT91_PIN_PD7, 0);	/* RTS1 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_B_periph(AT91_PIN_PD8, 0);	/* CTS1 */
-}
-
-static struct resource uart2_resources[] = {
-	[0] = {
-		.start	= AT91SAM9263_BASE_US2,
-		.end	= AT91SAM9263_BASE_US2 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9263_ID_US2,
-		.end	= NR_IRQS_LEGACY + AT91SAM9263_ID_US2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart2_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart2_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_uart2_device = {
-	.name		= "atmel_usart",
-	.id		= 3,
-	.dev		= {
-				.dma_mask		= &uart2_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart2_data,
-	},
-	.resource	= uart2_resources,
-	.num_resources	= ARRAY_SIZE(uart2_resources),
-};
-
-static inline void configure_usart2_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PD2, 1);		/* TXD2 */
-	at91_set_A_periph(AT91_PIN_PD3, 0);		/* RXD2 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_B_periph(AT91_PIN_PD5, 0);	/* RTS2 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_B_periph(AT91_PIN_PD6, 0);	/* CTS2 */
-}
-
-static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
-
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
-{
-	struct platform_device *pdev;
-	struct atmel_uart_data *pdata;
-
-	switch (id) {
-		case 0:		/* DBGU */
-			pdev = &at91sam9263_dbgu_device;
-			configure_dbgu_pins();
-			break;
-		case AT91SAM9263_ID_US0:
-			pdev = &at91sam9263_uart0_device;
-			configure_usart0_pins(pins);
-			break;
-		case AT91SAM9263_ID_US1:
-			pdev = &at91sam9263_uart1_device;
-			configure_usart1_pins(pins);
-			break;
-		case AT91SAM9263_ID_US2:
-			pdev = &at91sam9263_uart2_device;
-			configure_usart2_pins(pins);
-			break;
-		default:
-			return;
-	}
-	pdata = pdev->dev.platform_data;
-	pdata->num = portnr;		/* update to mapped ID */
-
-	if (portnr < ATMEL_MAX_UART)
-		at91_uarts[portnr] = pdev;
-}
-
-void __init at91_add_device_serial(void)
-{
-	int i;
-
-	for (i = 0; i < ATMEL_MAX_UART; i++) {
-		if (at91_uarts[i])
-			platform_device_register(at91_uarts[i]);
-	}
-}
-#else
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_add_device_serial(void) {}
-#endif
-
-
-/* -------------------------------------------------------------------- */
-/*
- * These devices are always present and don't need any board-specific
- * setup.
- */
-static int __init at91_add_standard_devices(void)
-{
-	if (of_have_populated_dt())
-		return 0;
-
-	at91_add_device_rtt();
-	at91_add_device_watchdog();
-	at91_add_device_tc();
-	return 0;
-}
-
-arch_initcall(at91_add_standard_devices);

arch/arm/mach-at91/at91sam9g45.c

@@ -11,7 +11,6 @@
  */
 
 #include <asm/system_misc.h>
-#include <mach/cpu.h>
 #include <mach/hardware.h>
 
 #include "soc.h"
@@ -34,13 +33,7 @@ static void __init at91sam9g45_initialize(void)
 	at91_sysirq_mask_rtt(AT91SAM9G45_BASE_RTT);
 }
 
-static void __init at91sam9g45_init_time(void)
-{
-	at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
-}
-
 AT91_SOC_START(at91sam9g45)
 	.map_io = at91sam9g45_map_io,
 	.init = at91sam9g45_initialize,
-	.init_time = at91sam9g45_init_time,
 AT91_SOC_END

arch/arm/mach-at91/at91sam9n12.c

@@ -6,219 +6,11 @@
  * Licensed under GPLv2 or later.
  */
 
-#include <linux/module.h>
-#include <linux/dma-mapping.h>
-#include <linux/clk/at91_pmc.h>
+#include <asm/system_misc.h>
+#include <mach/hardware.h>
 
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <mach/at91sam9n12.h>
-#include <mach/cpu.h>
-
-#include "board.h"
 #include "soc.h"
 #include "generic.h"
-#include "sam9_smc.h"
-
-#if defined(CONFIG_OLD_CLK_AT91)
-#include "clock.h"
-/* --------------------------------------------------------------------
- *  Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk pioAB_clk = {
-	.name		= "pioAB_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_PIOAB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioCD_clk = {
-	.name		= "pioCD_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_PIOCD,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
-	.name		= "usart0_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_USART0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
-	.name		= "usart1_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_USART1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
-	.name		= "usart2_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_USART2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart3_clk = {
-	.name		= "usart3_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_USART3,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi0_clk = {
-	.name		= "twi0_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_TWI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi1_clk = {
-	.name		= "twi1_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_TWI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc_clk = {
-	.name		= "mci_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_MCI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi0_clk = {
-	.name		= "spi0_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_SPI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi1_clk = {
-	.name		= "spi1_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_SPI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk uart0_clk = {
-	.name		= "uart0_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_UART0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk uart1_clk = {
-	.name		= "uart1_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_UART1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tcb_clk = {
-	.name		= "tcb_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_TCB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pwm_clk = {
-	.name		= "pwm_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_PWM,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk adc_clk = {
-	.name		= "adc_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_ADC,
-	.type	= CLK_TYPE_PERIPHERAL,
-};
-static struct clk dma_clk = {
-	.name		= "dma_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_DMA,
-	.type	= CLK_TYPE_PERIPHERAL,
-};
-static struct clk uhp_clk = {
-	.name		= "uhp",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_UHP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk udp_clk = {
-	.name		= "udp_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_UDP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk lcdc_clk = {
-	.name		= "lcdc_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_LCDC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc_clk = {
-	.name		= "ssc_clk",
-	.pmc_mask	= 1 << AT91SAM9N12_ID_SSC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk *periph_clocks[] __initdata = {
-	&pioAB_clk,
-	&pioCD_clk,
-	&usart0_clk,
-	&usart1_clk,
-	&usart2_clk,
-	&usart3_clk,
-	&twi0_clk,
-	&twi1_clk,
-	&mmc_clk,
-	&spi0_clk,
-	&spi1_clk,
-	&lcdc_clk,
-	&uart0_clk,
-	&uart1_clk,
-	&tcb_clk,
-	&pwm_clk,
-	&adc_clk,
-	&dma_clk,
-	&uhp_clk,
-	&udp_clk,
-	&ssc_clk,
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
-	/* lookup table for DT entries */
-	CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
-	CLKDEV_CON_DEV_ID("usart", "f801c000.serial", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "f8020000.serial", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "f8024000.serial", &usart2_clk),
-	CLKDEV_CON_DEV_ID("usart", "f8028000.serial", &usart3_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "f0008000.mmc", &mmc_clk),
-	CLKDEV_CON_DEV_ID(NULL, "f0010000.ssc", &ssc_clk),
-	CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma_clk),
-	CLKDEV_CON_DEV_ID(NULL, "f8010000.i2c", &twi0_clk),
-	CLKDEV_CON_DEV_ID(NULL, "f8014000.i2c", &twi1_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "f0000000.spi", &spi0_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "f0004000.spi", &spi1_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioAB_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioAB_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCD_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCD_clk),
-	/* additional fake clock for macb_hclk */
-	CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &uhp_clk),
-	CLKDEV_CON_DEV_ID("ohci_clk", "500000.ohci", &uhp_clk),
-	CLKDEV_CON_DEV_ID(NULL, "f8034000.pwm", &pwm_clk),
-};
-
-/*
- * The two programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
-	.name		= "pck0",
-	.pmc_mask	= AT91_PMC_PCK0,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 0,
-};
-static struct clk pck1 = {
-	.name		= "pck1",
-	.pmc_mask	= AT91_PMC_PCK1,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 1,
-};
-
-static void __init at91sam9n12_register_clocks(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
-		clk_register(periph_clocks[i]);
-	clk_register(&pck0);
-	clk_register(&pck1);
-
-	clkdev_add_table(periph_clocks_lookups,
-			 ARRAY_SIZE(periph_clocks_lookups));
-
-}
-#else
-#define at91sam9n12_register_clocks NULL
-#endif
 
 /* --------------------------------------------------------------------
  *  AT91SAM9N12 processor initialization
@@ -236,6 +28,5 @@ static void __init at91sam9n12_initialize(void)
 
 AT91_SOC_START(at91sam9n12)
 	.map_io = at91sam9n12_map_io,
-	.register_clocks = at91sam9n12_register_clocks,
 	.init = at91sam9n12_initialize,
 AT91_SOC_END

arch/arm/mach-at91/at91sam9rl.c

@@ -46,13 +46,7 @@ static void __init at91sam9rl_initialize(void)
 	at91_sysirq_mask_rtt(AT91SAM9RL_BASE_RTT);
 }
 
-static void __init at91sam9rl_init_time(void)
-{
-	at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
-}
-
 AT91_SOC_START(at91sam9rl)
 	.map_io = at91sam9rl_map_io,
 	.init = at91sam9rl_initialize,
-	.init_time = at91sam9rl_init_time,
 AT91_SOC_END

arch/arm/mach-at91/at91sam9x5.c

@@ -6,317 +6,11 @@
  * Licensed under GPLv2 or later.
  */
 
-#include <linux/module.h>
-#include <linux/dma-mapping.h>
-#include <linux/clk/at91_pmc.h>
+#include <asm/system_misc.h>
+#include <mach/hardware.h>
 
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <mach/at91sam9x5.h>
-#include <mach/cpu.h>
-
-#include "board.h"
 #include "soc.h"
 #include "generic.h"
-#include "sam9_smc.h"
-
-#if defined(CONFIG_OLD_CLK_AT91)
-#include "clock.h"
-/* --------------------------------------------------------------------
- *  Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk pioAB_clk = {
-	.name		= "pioAB_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_PIOAB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioCD_clk = {
-	.name		= "pioCD_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_PIOCD,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk smd_clk = {
-	.name		= "smd_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_SMD,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
-	.name		= "usart0_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_USART0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
-	.name		= "usart1_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_USART1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
-	.name		= "usart2_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_USART2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-/* USART3 clock - Only for sam9g25/sam9x25 */
-static struct clk usart3_clk = {
-	.name		= "usart3_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_USART3,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi0_clk = {
-	.name		= "twi0_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_TWI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi1_clk = {
-	.name		= "twi1_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_TWI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi2_clk = {
-	.name		= "twi2_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_TWI2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc0_clk = {
-	.name		= "mci0_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_MCI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi0_clk = {
-	.name		= "spi0_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_SPI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi1_clk = {
-	.name		= "spi1_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_SPI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk uart0_clk = {
-	.name		= "uart0_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_UART0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk uart1_clk = {
-	.name		= "uart1_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_UART1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tcb0_clk = {
-	.name		= "tcb0_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_TCB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pwm_clk = {
-	.name		= "pwm_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_PWM,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk adc_clk = {
-	.name		= "adc_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_ADC,
-	.type	= CLK_TYPE_PERIPHERAL,
-};
-static struct clk adc_op_clk = {
-	.name		= "adc_op_clk",
-	.type		= CLK_TYPE_PERIPHERAL,
-	.rate_hz	= 5000000,
-};
-static struct clk dma0_clk = {
-	.name		= "dma0_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_DMA0,
-	.type	= CLK_TYPE_PERIPHERAL,
-};
-static struct clk dma1_clk = {
-	.name		= "dma1_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_DMA1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk uhphs_clk = {
-	.name		= "uhphs",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_UHPHS,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk udphs_clk = {
-	.name		= "udphs_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_UDPHS,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-/* emac0 clock - Only for sam9g25/sam9x25/sam9g35/sam9x35 */
-static struct clk macb0_clk = {
-	.name		= "pclk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_EMAC0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-/* lcd clock - Only for sam9g15/sam9g35/sam9x35 */
-static struct clk lcdc_clk = {
-	.name		= "lcdc_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_LCDC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-/* isi clock - Only for sam9g25 */
-static struct clk isi_clk = {
-	.name		= "isi_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_ISI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc1_clk = {
-	.name		= "mci1_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_MCI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-/* emac1 clock - Only for sam9x25 */
-static struct clk macb1_clk = {
-	.name		= "pclk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_EMAC1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc_clk = {
-	.name		= "ssc_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_SSC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-/* can0 clock - Only for sam9x35 */
-static struct clk can0_clk = {
-	.name		= "can0_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_CAN0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-/* can1 clock - Only for sam9x35 */
-static struct clk can1_clk = {
-	.name		= "can1_clk",
-	.pmc_mask	= 1 << AT91SAM9X5_ID_CAN1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk *periph_clocks[] __initdata = {
-	&pioAB_clk,
-	&pioCD_clk,
-	&smd_clk,
-	&usart0_clk,
-	&usart1_clk,
-	&usart2_clk,
-	&twi0_clk,
-	&twi1_clk,
-	&twi2_clk,
-	&mmc0_clk,
-	&spi0_clk,
-	&spi1_clk,
-	&uart0_clk,
-	&uart1_clk,
-	&tcb0_clk,
-	&pwm_clk,
-	&adc_clk,
-	&adc_op_clk,
-	&dma0_clk,
-	&dma1_clk,
-	&uhphs_clk,
-	&udphs_clk,
-	&mmc1_clk,
-	&ssc_clk,
-	// irq0
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
-	/* lookup table for DT entries */
-	CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
-	CLKDEV_CON_DEV_ID("usart", "f801c000.serial", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "f8020000.serial", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "f8024000.serial", &usart2_clk),
-	CLKDEV_CON_DEV_ID("usart", "f8028000.serial", &usart3_clk),
-	CLKDEV_CON_DEV_ID("usart", "f8040000.serial", &uart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "f8044000.serial", &uart1_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb0_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb0_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "f0008000.mmc", &mmc0_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "f000c000.mmc", &mmc1_clk),
-	CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma0_clk),
-	CLKDEV_CON_DEV_ID("dma_clk", "ffffee00.dma-controller", &dma1_clk),
-	CLKDEV_CON_DEV_ID("pclk", "f0010000.ssc", &ssc_clk),
-	CLKDEV_CON_DEV_ID(NULL, "f8010000.i2c", &twi0_clk),
-	CLKDEV_CON_DEV_ID(NULL, "f8014000.i2c", &twi1_clk),
-	CLKDEV_CON_DEV_ID(NULL, "f8018000.i2c", &twi2_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "f0000000.spi", &spi0_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "f0004000.spi", &spi1_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioAB_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioAB_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCD_clk),
-	CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCD_clk),
-	/* additional fake clock for macb_hclk */
-	CLKDEV_CON_DEV_ID("hclk", "f802c000.ethernet", &macb0_clk),
-	CLKDEV_CON_DEV_ID("hclk", "f8030000.ethernet", &macb1_clk),
-	CLKDEV_CON_DEV_ID("hclk", "600000.ohci", &uhphs_clk),
-	CLKDEV_CON_DEV_ID("ohci_clk", "600000.ohci", &uhphs_clk),
-	CLKDEV_CON_DEV_ID("ehci_clk", "700000.ehci", &uhphs_clk),
-	CLKDEV_CON_DEV_ID("hclk", "500000.gadget", &utmi_clk),
-	CLKDEV_CON_DEV_ID("pclk", "500000.gadget", &udphs_clk),
-	CLKDEV_CON_DEV_ID(NULL, "f8034000.pwm", &pwm_clk),
-};
-
-/*
- * The two programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
-	.name		= "pck0",
-	.pmc_mask	= AT91_PMC_PCK0,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 0,
-};
-static struct clk pck1 = {
-	.name		= "pck1",
-	.pmc_mask	= AT91_PMC_PCK1,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 1,
-};
-
-static void __init at91sam9x5_register_clocks(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
-		clk_register(periph_clocks[i]);
-
-	clkdev_add_table(periph_clocks_lookups,
-			 ARRAY_SIZE(periph_clocks_lookups));
-
-	if (cpu_is_at91sam9g25()
-	|| cpu_is_at91sam9x25())
-		clk_register(&usart3_clk);
-
-	if (cpu_is_at91sam9g25()
-	|| cpu_is_at91sam9x25()
-	|| cpu_is_at91sam9g35()
-	|| cpu_is_at91sam9x35())
-		clk_register(&macb0_clk);
-
-	if (cpu_is_at91sam9g15()
-	|| cpu_is_at91sam9g35()
-	|| cpu_is_at91sam9x35())
-		clk_register(&lcdc_clk);
-
-	if (cpu_is_at91sam9g25())
-		clk_register(&isi_clk);
-
-	if (cpu_is_at91sam9x25())
-		clk_register(&macb1_clk);
-
-	if (cpu_is_at91sam9x25()
-	|| cpu_is_at91sam9x35()) {
-		clk_register(&can0_clk);
-		clk_register(&can1_clk);
-	}
-
-	clk_register(&pck0);
-	clk_register(&pck1);
-}
-#else
-#define at91sam9x5_register_clocks	NULL
-#endif
 
 /* --------------------------------------------------------------------
  *  AT91SAM9x5 processor initialization
@@ -338,6 +32,5 @@ static void __init at91sam9x5_initialize(void)
 
 AT91_SOC_START(at91sam9x5)
 	.map_io = at91sam9x5_map_io,
-	.register_clocks = at91sam9x5_register_clocks,
 	.init = at91sam9x5_initialize,
 AT91_SOC_END

arch/arm/mach-at91/board-1arm.c

@@ -1,99 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-1arm.c
- *
- *  Copyright (C) 2005 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/cpu.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-static void __init onearm_init_early(void)
-{
-	/* Set cpu type: PQFP */
-	at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
-
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata onearm_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 1,
-};
-
-static struct at91_usbh_data __initdata onearm_usbh_data = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata onearm_udc_data = {
-	.vbus_pin	= AT91_PIN_PC2,
-	.pullup_pin	= AT91_PIN_PC3,
-};
-
-static void __init onearm_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&onearm_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&onearm_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&onearm_udc_data);
-}
-
-MACHINE_START(ONEARM, "Ajeco 1ARM single board computer")
-	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= onearm_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= onearm_board_init,
-MACHINE_END

arch/arm/mach-at91/board-afeb-9260v1.c

@@ -1,223 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-afeb-9260v1.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2006 Atmel
- *  Copyright (C) 2008 Sergey Lapin
- *
- * A custom board designed as open hardware; PCBs and various information
- * is available at http://groups.google.com/group/arm9fpga-evolution-board/
- * Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/clk.h>
-#include <linux/dma-mapping.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init afeb9260_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata afeb9260_usbh_data = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata afeb9260_udc_data = {
-	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-
-/*
- * SPI devices.
- */
-static struct spi_board_info afeb9260_spi_devices[] = {
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata afeb9260_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA9,
-	.is_rmii	= 0,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata afeb9260_nand_partition[] = {
-	{
-		.name	= "bootloader",
-		.offset	= 0,
-		.size	= (640 * SZ_1K),
-	},
-	{
-		.name	= "kernel",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= SZ_2M,
-	},
-	{
-		.name	= "rootfs",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata afeb9260_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.bus_width_16	= 0,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.parts		= afeb9260_nand_partition,
-	.num_parts	= ARRAY_SIZE(afeb9260_nand_partition),
-	.det_pin	= -EINVAL,
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata afeb9260_mci0_data = {
-	.slot[1] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PC9,
-		.wp_pin		= AT91_PIN_PC4,
-	},
-};
-
-
-
-static struct i2c_board_info __initdata afeb9260_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("tlv320aic23", 0x1a),
-	}, {
-		I2C_BOARD_INFO("fm3130", 0x68),
-	}, {
-		I2C_BOARD_INFO("24c64", 0x50),
-	},
-};
-
-/*
- * IDE (CF True IDE mode)
- */
-static struct at91_cf_data afeb9260_cf_data = {
-	.chipselect = 4,
-	.irq_pin    = AT91_PIN_PA6,
-	.det_pin	= -EINVAL,
-	.vcc_pin	= -EINVAL,
-	.rst_pin    = AT91_PIN_PA7,
-	.flags      = AT91_CF_TRUE_IDE,
-};
-
-static void __init afeb9260_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-			     ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR
-			   | ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-			ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&afeb9260_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&afeb9260_udc_data);
-	/* SPI */
-	at91_add_device_spi(afeb9260_spi_devices,
-			ARRAY_SIZE(afeb9260_spi_devices));
-	/* NAND */
-	at91_add_device_nand(&afeb9260_nand_data);
-	/* Ethernet */
-	at91_add_device_eth(&afeb9260_macb_data);
-
-	/* Standard function's pin assignments are not
-	 * appropriate for us and generic code provide
-	 * no API to configure these pins any other way */
-	at91_set_B_periph(AT91_PIN_PA10, 0);	/* ETX2 */
-	at91_set_B_periph(AT91_PIN_PA11, 0);	/* ETX3 */
-	/* MMC */
-	at91_add_device_mci(0, &afeb9260_mci0_data);
-	/* I2C */
-	at91_add_device_i2c(afeb9260_i2c_devices,
-			ARRAY_SIZE(afeb9260_i2c_devices));
-	/* Audio */
-	at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
-	/* IDE */
-	at91_add_device_cf(&afeb9260_cf_data);
-}
-
-MACHINE_START(AFEB9260, "Custom afeb9260 board")
-	/* Maintainer: Sergey Lapin <slapin@ossfans.org> */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= afeb9260_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= afeb9260_board_init,
-MACHINE_END
-

arch/arm/mach-at91/board-cam60.c

@@ -1,199 +0,0 @@
-/*
- * KwikByte CAM60 (KB9260)
- *
- * based on board-sam9260ek.c
- *   Copyright (C) 2005 SAN People
- *   Copyright (C) 2006 Atmel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/at91sam9_smc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init cam60_init_early(void)
-{
-	/* Initialize processor: 10 MHz crystal */
-	at91_initialize(10000000);
-}
-
-/*
- * USB Host
- */
-static struct at91_usbh_data __initdata cam60_usbh_data = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-
-/*
- * SPI devices.
- */
-#if defined(CONFIG_MTD_DATAFLASH)
-static struct mtd_partition cam60_spi_partitions[] = {
-	{
-		.name	= "BOOT1",
-		.offset	= 0,
-		.size	= 4 * 1056,
-	},
-	{
-		.name	= "BOOT2",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 256 * 1056,
-	},
-	{
-		.name	= "kernel",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 2222 * 1056,
-	},
-	{
-		.name	= "file system",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct flash_platform_data cam60_spi_flash_platform_data = {
-	.name		= "spi_flash",
-	.parts		= cam60_spi_partitions,
-	.nr_parts	= ARRAY_SIZE(cam60_spi_partitions)
-};
-#endif
-
-static struct spi_board_info cam60_spi_devices[] __initdata = {
-#if defined(CONFIG_MTD_DATAFLASH)
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-		.platform_data	= &cam60_spi_flash_platform_data
-	},
-#endif
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data cam60_macb_data __initdata = {
-	.phy_irq_pin	= AT91_PIN_PB5,
-	.is_rmii	= 0,
-};
-
-
-/*
- * NAND Flash
- */
-static struct mtd_partition __initdata cam60_nand_partition[] = {
-	{
-		.name	= "nand_fs",
-		.offset	= 0,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata cam60_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PA9,
-	.enable_pin	= AT91_PIN_PA7,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.parts		= cam60_nand_partition,
-	.num_parts	= ARRAY_SIZE(cam60_nand_partition),
-};
-
-static struct sam9_smc_config __initdata cam60_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 2,
-};
-
-static void __init cam60_add_device_nand(void)
-{
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &cam60_nand_smc_config);
-
-	at91_add_device_nand(&cam60_nand_data);
-}
-
-
-static void __init cam60_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-	at91_add_device_serial();
-	/* SPI */
-	at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices));
-	/* Ethernet */
-	at91_add_device_eth(&cam60_macb_data);
-	/* USB Host */
-	/* enable USB power supply circuit */
-	at91_set_gpio_output(AT91_PIN_PB18, 1);
-	at91_add_device_usbh(&cam60_usbh_data);
-	/* NAND */
-	cam60_add_device_nand();
-}
-
-MACHINE_START(CAM60, "KwikByte CAM60")
-	/* Maintainer: KwikByte */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= cam60_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= cam60_board_init,
-MACHINE_END

arch/arm/mach-at91/board-carmeva.c

@@ -1,167 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-carmeva.c
- *
- *  Copyright (c) 2005 Peer Georgi
- *  		       Conitec Datasystems
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init carmeva_init_early(void)
-{
-	/* Initialize processor: 20.000 MHz crystal */
-	at91_initialize(20000000);
-}
-
-static struct macb_platform_data __initdata carmeva_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 1,
-};
-
-static struct at91_usbh_data __initdata carmeva_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata carmeva_udc_data = {
-	.vbus_pin	= AT91_PIN_PD12,
-	.pullup_pin	= AT91_PIN_PD9,
-};
-
-/* FIXME: user dependent */
-// static struct at91_cf_data __initdata carmeva_cf_data = {
-//	.det_pin	= AT91_PIN_PB0,
-//	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= -EINVAL,
-	// .vcc_pin	= -EINVAL,
-// };
-
-static struct mci_platform_data __initdata carmeva_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PB10,
-		.wp_pin		= AT91_PIN_PC14,
-	},
-};
-
-static struct spi_board_info carmeva_spi_devices[] = {
-	{ /* DataFlash chip */
-		.modalias = "mtd_dataflash",
-		.chip_select  = 0,
-		.max_speed_hz = 10 * 1000 * 1000,
-	},
-	{ /* User accessible spi - cs1 (250KHz) */
-		.modalias = "spi-cs1",
-		.chip_select  = 1,
-		.max_speed_hz = 250 *  1000,
-	},
-	{ /* User accessible spi - cs2 (1MHz) */
-		.modalias = "spi-cs2",
-		.chip_select  = 2,
-		.max_speed_hz = 1 * 1000 *  1000,
-	},
-	{ /* User accessible spi - cs3 (10MHz) */
-		.modalias = "spi-cs3",
-		.chip_select  = 3,
-		.max_speed_hz = 10 * 1000 *  1000,
-	},
-};
-
-static struct gpio_led carmeva_leds[] = {
-	{ /* "user led 1", LED9 */
-		.name			= "led9",
-		.gpio			= AT91_PIN_PA21,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	},
-	{ /* "user led 2", LED10 */
-		.name			= "led10",
-		.gpio			= AT91_PIN_PA25,
-		.active_low		= 1,
-	},
-	{ /* "user led 3", LED11 */
-		.name			= "led11",
-		.gpio			= AT91_PIN_PA26,
-		.active_low		= 1,
-	},
-	{ /* "user led 4", LED12 */
-		.name			= "led12",
-		.gpio			= AT91_PIN_PA18,
-		.active_low		= 1,
-	}
-};
-
-static void __init carmeva_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&carmeva_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&carmeva_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&carmeva_udc_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* SPI */
-	at91_add_device_spi(carmeva_spi_devices, ARRAY_SIZE(carmeva_spi_devices));
-	/* Compact Flash */
-//	at91_add_device_cf(&carmeva_cf_data);
-	/* MMC */
-	at91_add_device_mci(0, &carmeva_mci0_data);
-	/* LEDs */
-	at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds));
-}
-
-MACHINE_START(CARMEVA, "Carmeva")
-	/* Maintainer: Conitec Datasystems */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= carmeva_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= carmeva_board_init,
-MACHINE_END

arch/arm/mach-at91/board-cpu9krea.c

@@ -1,386 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-cpu9krea.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2006 Atmel
- *  Copyright (C) 2009 Eric Benard - eric@eukrea.com
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/at91sam9260_matrix.h>
-#include <mach/at91_matrix.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-static void __init cpu9krea_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata cpu9krea_udc_data = {
-	.vbus_pin	= AT91_PIN_PC8,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata cpu9krea_macb_data = {
-	.phy_irq_pin	= -EINVAL,
-	.is_rmii	= 1,
-};
-
-/*
- * NAND flash
- */
-static struct atmel_nand_data __initdata cpu9krea_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.bus_width_16	= 0,
-	.det_pin	= -EINVAL,
-	.ecc_mode	= NAND_ECC_SOFT,
-};
-
-#ifdef CONFIG_MACH_CPU9260
-static struct sam9_smc_config __initdata cpu9krea_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-		| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 2,
-};
-#else
-static struct sam9_smc_config __initdata cpu9krea_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-		| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 3,
-};
-#endif
-
-static void __init cpu9krea_add_device_nand(void)
-{
-	sam9_smc_configure(0, 3, &cpu9krea_nand_smc_config);
-	at91_add_device_nand(&cpu9krea_nand_data);
-}
-
-/*
- * NOR flash
- */
-static struct physmap_flash_data cpuat9260_nor_data = {
-	.width		= 2,
-};
-
-#define NOR_BASE	AT91_CHIPSELECT_0
-#define NOR_SIZE	SZ_64M
-
-static struct resource nor_flash_resources[] = {
-	{
-		.start	= NOR_BASE,
-		.end	= NOR_BASE + NOR_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device cpu9krea_nor_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &cpuat9260_nor_data,
-	},
-	.resource	= nor_flash_resources,
-	.num_resources	= ARRAY_SIZE(nor_flash_resources),
-};
-
-#ifdef CONFIG_MACH_CPU9260
-static struct sam9_smc_config __initdata cpu9krea_nor_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 10,
-	.nrd_pulse		= 10,
-	.ncs_write_pulse	= 6,
-	.nwe_pulse		= 6,
-
-	.read_cycle		= 12,
-	.write_cycle		= 8,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-			| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE
-			| AT91_SMC_DBW_16,
-	.tdf_cycles		= 2,
-};
-#else
-static struct sam9_smc_config __initdata cpu9krea_nor_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 13,
-	.nrd_pulse		= 13,
-	.ncs_write_pulse	= 8,
-	.nwe_pulse		= 8,
-
-	.read_cycle		= 15,
-	.write_cycle		= 10,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-			| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE
-			| AT91_SMC_DBW_16,
-	.tdf_cycles		= 2,
-};
-#endif
-
-static __init void cpu9krea_add_device_nor(void)
-{
-	unsigned long csa;
-
-	csa = at91_matrix_read(AT91_MATRIX_EBICSA);
-	at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_VDDIOMSEL_3_3V);
-
-	/* configure chip-select 0 (NOR) */
-	sam9_smc_configure(0, 0, &cpu9krea_nor_smc_config);
-
-	platform_device_register(&cpu9krea_nor_flash);
-}
-
-/*
- * LEDs
- */
-static struct gpio_led cpu9krea_leds[] = {
-	{	/* LED1 */
-		.name			= "LED1",
-		.gpio			= AT91_PIN_PC11,
-		.active_low		= 1,
-		.default_trigger	= "timer",
-	},
-	{	/* LED2 */
-		.name			= "LED2",
-		.gpio			= AT91_PIN_PC12,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	},
-	{	/* LED3 */
-		.name			= "LED3",
-		.gpio			= AT91_PIN_PC7,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* LED4 */
-		.name			= "LED4",
-		.gpio			= AT91_PIN_PC9,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	}
-};
-
-static struct i2c_board_info __initdata cpu9krea_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("ds1339", 0x68),
-	},
-};
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button cpu9krea_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PC3,
-		.code		= BTN_0,
-		.desc		= "BP1",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PB20,
-		.code		= BTN_1,
-		.desc		= "BP2",
-		.active_low	= 1,
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data cpu9krea_button_data = {
-	.buttons	= cpu9krea_buttons,
-	.nbuttons	= ARRAY_SIZE(cpu9krea_buttons),
-};
-
-static struct platform_device cpu9krea_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &cpu9krea_button_data,
-	}
-};
-
-static void __init cpu9krea_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PC3, 1);	/* BP1 */
-	at91_set_deglitch(AT91_PIN_PC3, 1);
-	at91_set_gpio_input(AT91_PIN_PB20, 1);	/* BP2 */
-	at91_set_deglitch(AT91_PIN_PB20, 1);
-
-	platform_device_register(&cpu9krea_button_device);
-}
-#else
-static void __init cpu9krea_add_device_buttons(void)
-{
-}
-#endif
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata cpu9krea_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PA29,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-static void __init cpu9krea_board_init(void)
-{
-	at91_register_devices();
-
-	/* NOR */
-	cpu9krea_add_device_nor();
-	/* Serial */
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS |
-		ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
-		ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
-
-	/* USART3 on ttyS4. (Rx, Tx) */
-	at91_register_uart(AT91SAM9260_ID_US3, 4, 0);
-
-	/* USART4 on ttyS5. (Rx, Tx) */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
-	/* USART5 on ttyS6. (Rx, Tx) */
-	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&cpu9krea_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&cpu9krea_udc_data);
-	/* NAND */
-	cpu9krea_add_device_nand();
-	/* Ethernet */
-	at91_add_device_eth(&cpu9krea_macb_data);
-	/* MMC */
-	at91_add_device_mci(0, &cpu9krea_mci0_data);
-	/* I2C */
-	at91_add_device_i2c(cpu9krea_i2c_devices,
-		ARRAY_SIZE(cpu9krea_i2c_devices));
-	/* LEDs */
-	at91_gpio_leds(cpu9krea_leds, ARRAY_SIZE(cpu9krea_leds));
-	/* Push Buttons */
-	cpu9krea_add_device_buttons();
-}
-
-#ifdef CONFIG_MACH_CPU9260
-MACHINE_START(CPUAT9260, "Eukrea CPU9260")
-#else
-MACHINE_START(CPUAT9G20, "Eukrea CPU9G20")
-#endif
-	/* Maintainer: Eric Benard - EUKREA Electromatique */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= cpu9krea_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= cpu9krea_board_init,
-MACHINE_END

arch/arm/mach-at91/board-cpuat91.c

@@ -1,189 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-cpuat91.c
- *
- *  Copyright (C) 2009 Eric Benard - eric@eukrea.com
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/plat-ram.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-#include <mach/cpu.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static struct gpio_led cpuat91_leds[] = {
-	{
-		.name			= "led1",
-		.default_trigger	= "heartbeat",
-		.active_low		= 1,
-		.gpio			= AT91_PIN_PC0,
-	},
-};
-
-static void __init cpuat91_init_early(void)
-{
-	/* Set cpu type: PQFP */
-	at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
-
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata cpuat91_eth_data = {
-	.phy_irq_pin	= -EINVAL,
-	.is_rmii	= 1,
-};
-
-static struct at91_usbh_data __initdata cpuat91_usbh_data = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata cpuat91_udc_data = {
-	.vbus_pin	= AT91_PIN_PC15,
-	.pullup_pin	= AT91_PIN_PC14,
-};
-
-static struct mci_platform_data __initdata cpuat91_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PC2,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-static struct physmap_flash_data cpuat91_flash_data = {
-	.width		= 2,
-};
-
-static struct resource cpuat91_flash_resource = {
-	.start		= AT91_CHIPSELECT_0,
-	.end		= AT91_CHIPSELECT_0 + SZ_16M - 1,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device cpuat91_norflash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev	= {
-		.platform_data	= &cpuat91_flash_data,
-	},
-	.resource	= &cpuat91_flash_resource,
-	.num_resources	= 1,
-};
-
-#ifdef CONFIG_MTD_PLATRAM
-struct platdata_mtd_ram at91_sram_pdata = {
-	.mapname	= "SRAM",
-	.bankwidth	= 2,
-};
-
-static struct resource at91_sram_resource[] = {
-	[0] = {
-		.start = AT91RM9200_SRAM_BASE,
-		.end   = AT91RM9200_SRAM_BASE + AT91RM9200_SRAM_SIZE - 1,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device at91_sram = {
-	.name		= "mtd-ram",
-	.id		= 0,
-	.resource	= at91_sram_resource,
-	.num_resources	= ARRAY_SIZE(at91_sram_resource),
-	.dev	= {
-		.platform_data = &at91_sram_pdata,
-	},
-};
-#endif /* MTD_PLATRAM */
-
-static struct platform_device *platform_devices[] __initdata = {
-	&cpuat91_norflash,
-#ifdef CONFIG_MTD_PLATRAM
-	&at91_sram,
-#endif /* CONFIG_MTD_PLATRAM */
-};
-
-static void __init cpuat91_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
-		ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
-		ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART2 on ttyS3 (Rx, Tx) */
-	at91_register_uart(AT91RM9200_ID_US2, 3, 0);
-
-	/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* LEDs. */
-	at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds));
-	/* Ethernet */
-	at91_add_device_eth(&cpuat91_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&cpuat91_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&cpuat91_udc_data);
-	/* MMC */
-	at91_add_device_mci(0, &cpuat91_mci0_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* Platform devices */
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-}
-
-MACHINE_START(CPUAT91, "Eukrea")
-	/* Maintainer: Eric Benard - EUKREA Electromatique */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= cpuat91_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= cpuat91_board_init,
-MACHINE_END

arch/arm/mach-at91/board-csb337.c

@@ -1,260 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-csb337.c
- *
- *  Copyright (C) 2005 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-static void __init csb337_init_early(void)
-{
-	/* Initialize processor: 3.6864 MHz crystal */
-	at91_initialize(3686400);
-}
-
-static struct macb_platform_data __initdata csb337_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC2,
-	.is_rmii	= 0,
-	/* The CSB337 bootloader stores the MAC the wrong-way around */
-	.rev_eth_addr	= 1,
-};
-
-static struct at91_usbh_data __initdata csb337_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata csb337_udc_data = {
-	.pullup_pin	= AT91_PIN_PA24,
-	.vbus_pin	= -EINVAL,
-};
-
-static struct i2c_board_info __initdata csb337_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("ds1307", 0x68),
-	},
-};
-
-static struct at91_cf_data __initdata csb337_cf_data = {
-	/*
-	 * connector P4 on the CSB 337 mates to
-	 * connector P8 on the CSB 300CF
-	 */
-
-	/* CSB337 specific */
-	.det_pin	= AT91_PIN_PC3,
-
-	/* CSB300CF specific */
-	.irq_pin	= AT91_PIN_PA19,
-	.vcc_pin	= AT91_PIN_PD0,
-	.rst_pin	= AT91_PIN_PD2,
-};
-
-static struct mci_platform_data __initdata csb337_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PD5,
-		.wp_pin		= AT91_PIN_PD6,
-	},
-};
-
-static struct spi_board_info csb337_spi_devices[] = {
-	{	/* CAN controller */
-		.modalias	= "sak82c900",
-		.chip_select	= 0,
-		.max_speed_hz	= 6 * 1000 * 1000,
-	},
-};
-
-#define CSB_FLASH_BASE	AT91_CHIPSELECT_0
-#define CSB_FLASH_SIZE	SZ_8M
-
-static struct mtd_partition csb_flash_partitions[] = {
-	{
-		.name		= "uMON flash",
-		.offset		= 0,
-		.size		= MTDPART_SIZ_FULL,
-		.mask_flags	= MTD_WRITEABLE,	/* read only */
-	}
-};
-
-static struct physmap_flash_data csb_flash_data = {
-	.width		= 2,
-	.parts		= csb_flash_partitions,
-	.nr_parts	= ARRAY_SIZE(csb_flash_partitions),
-};
-
-static struct resource csb_flash_resources[] = {
-	{
-		.start	= CSB_FLASH_BASE,
-		.end	= CSB_FLASH_BASE + CSB_FLASH_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device csb_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-				.platform_data = &csb_flash_data,
-			},
-	.resource	= csb_flash_resources,
-	.num_resources	= ARRAY_SIZE(csb_flash_resources),
-};
-
-/*
- * GPIO Buttons (on CSB300)
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button csb300_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PB29,
-		.code		= BTN_0,
-		.desc		= "sw0",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PB28,
-		.code		= BTN_1,
-		.desc		= "sw1",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PA21,
-		.code		= BTN_2,
-		.desc		= "sw2",
-		.active_low	= 1,
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data csb300_button_data = {
-	.buttons	= csb300_buttons,
-	.nbuttons	= ARRAY_SIZE(csb300_buttons),
-};
-
-static struct platform_device csb300_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &csb300_button_data,
-	}
-};
-
-static void __init csb300_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PB29, 1);	/* sw0 */
-	at91_set_deglitch(AT91_PIN_PB29, 1);
-	at91_set_gpio_input(AT91_PIN_PB28, 1);	/* sw1 */
-	at91_set_deglitch(AT91_PIN_PB28, 1);
-	at91_set_gpio_input(AT91_PIN_PA21, 1);	/* sw2 */
-	at91_set_deglitch(AT91_PIN_PA21, 1);
-
-	platform_device_register(&csb300_button_device);
-}
-#else
-static void __init csb300_add_device_buttons(void) {}
-#endif
-
-static struct gpio_led csb_leds[] = {
-	{	/* "led0", yellow */
-		.name			= "led0",
-		.gpio			= AT91_PIN_PB2,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	},
-	{	/* "led1", green */
-		.name			= "led1",
-		.gpio			= AT91_PIN_PB1,
-		.active_low		= 1,
-		.default_trigger	= "mmc0",
-	},
-	{	/* "led2", yellow */
-		.name			= "led2",
-		.gpio			= AT91_PIN_PB0,
-		.active_low		= 1,
-		.default_trigger	= "ide-disk",
-	}
-};
-
-
-static void __init csb337_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0 */
-	at91_register_uart(0, 0, 0);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&csb337_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&csb337_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&csb337_udc_data);
-	/* I2C */
-	at91_add_device_i2c(csb337_i2c_devices, ARRAY_SIZE(csb337_i2c_devices));
-	/* Compact Flash */
-	at91_set_gpio_input(AT91_PIN_PB22, 1);		/* IOIS16 */
-	at91_add_device_cf(&csb337_cf_data);
-	/* SPI */
-	at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
-	/* MMC */
-	at91_add_device_mci(0, &csb337_mci0_data);
-	/* NOR flash */
-	platform_device_register(&csb_flash);
-	/* LEDs */
-	at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
-	/* Switches on CSB300 */
-	csb300_add_device_buttons();
-}
-
-MACHINE_START(CSB337, "Cogent CSB337")
-	/* Maintainer: Bill Gatliff */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= csb337_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= csb337_board_init,
-MACHINE_END

arch/arm/mach-at91/board-csb637.c

@@ -1,142 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-csb637.c
- *
- *  Copyright (C) 2005 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init csb637_init_early(void)
-{
-	/* Initialize processor: 3.6864 MHz crystal */
-	at91_initialize(3686400);
-}
-
-static struct macb_platform_data __initdata csb637_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC0,
-	.is_rmii	= 0,
-};
-
-static struct at91_usbh_data __initdata csb637_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata csb637_udc_data = {
-	.vbus_pin     = AT91_PIN_PB28,
-	.pullup_pin   = AT91_PIN_PB1,
-};
-
-#define CSB_FLASH_BASE	AT91_CHIPSELECT_0
-#define CSB_FLASH_SIZE	SZ_16M
-
-static struct mtd_partition csb_flash_partitions[] = {
-	{
-		.name		= "uMON flash",
-		.offset		= 0,
-		.size		= MTDPART_SIZ_FULL,
-		.mask_flags	= MTD_WRITEABLE,	/* read only */
-	}
-};
-
-static struct physmap_flash_data csb_flash_data = {
-	.width		= 2,
-	.parts		= csb_flash_partitions,
-	.nr_parts	= ARRAY_SIZE(csb_flash_partitions),
-};
-
-static struct resource csb_flash_resources[] = {
-	{
-		.start	= CSB_FLASH_BASE,
-		.end	= CSB_FLASH_BASE + CSB_FLASH_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device csb_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-				.platform_data = &csb_flash_data,
-			},
-	.resource	= csb_flash_resources,
-	.num_resources	= ARRAY_SIZE(csb_flash_resources),
-};
-
-static struct gpio_led csb_leds[] = {
-	{	/* "d1", red */
-		.name			= "d1",
-		.gpio			= AT91_PIN_PB2,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	},
-};
-
-static void __init csb637_board_init(void)
-{
-	/* LED(s) */
-	at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&csb637_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&csb637_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&csb637_udc_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* SPI */
-	at91_add_device_spi(NULL, 0);
-	/* NOR flash */
-	platform_device_register(&csb_flash);
-}
-
-MACHINE_START(CSB637, "Cogent CSB637")
-	/* Maintainer: Bill Gatliff */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= csb637_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= csb637_board_init,
-MACHINE_END

arch/arm/mach-at91/board-dt-rm9200.c

@@ -22,14 +22,11 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include "at91_aic.h"
 #include "generic.h"
 
 static void __init at91rm9200_dt_timer_init(void)
 {
-#if defined(CONFIG_COMMON_CLK)
 	of_clk_init(NULL);
-#endif
 	at91rm9200_timer_init();
 }
 

arch/arm/mach-at91/board-dt-sam9.c

@@ -21,8 +21,6 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include "at91_aic.h"
-#include "board.h"
 #include "generic.h"
 
 static const char *at91_dt_board_compat[] __initdata = {

arch/arm/mach-at91/board-dt-sama5.c

@@ -24,7 +24,6 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include "at91_aic.h"
 #include "generic.h"
 
 static void __init sama5_dt_device_init(void)

arch/arm/mach-at91/board-eb9200.c

@@ -1,126 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-eb9200.c
- *
- *  Copyright (C) 2005 SAN People, adapted for ATEB9200 from Embest
- *  by Andrew Patrikalakis
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/device.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init eb9200_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata eb9200_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 1,
-};
-
-static struct at91_usbh_data __initdata eb9200_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata eb9200_udc_data = {
-	.vbus_pin	= AT91_PIN_PD4,
-	.pullup_pin	= AT91_PIN_PD5,
-};
-
-static struct at91_cf_data __initdata eb9200_cf_data = {
-	.irq_pin	= -EINVAL,
-	.det_pin	= AT91_PIN_PB0,
-	.vcc_pin	= -EINVAL,
-	.rst_pin	= AT91_PIN_PC5,
-};
-
-static struct mci_platform_data __initdata eb9200_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-static struct i2c_board_info __initdata eb9200_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c512", 0x50),
-	},
-};
-
-
-static void __init eb9200_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			| ATMEL_UART_RI);
-
-	/* USART2 on ttyS2. (Rx, Tx) - IRDA */
-	at91_register_uart(AT91RM9200_ID_US2, 2, 0);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&eb9200_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&eb9200_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&eb9200_udc_data);
-	/* I2C */
-	at91_add_device_i2c(eb9200_i2c_devices, ARRAY_SIZE(eb9200_i2c_devices));
-	/* Compact Flash */
-	at91_add_device_cf(&eb9200_cf_data);
-	/* SPI */
-	at91_add_device_spi(NULL, 0);
-	/* MMC */
-	/* only supports 1 or 4 bit interface, not wired through to SPI */
-	at91_add_device_mci(0, &eb9200_mci0_data);
-}
-
-MACHINE_START(ATEB9200, "Embest ATEB9200")
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= eb9200_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= eb9200_board_init,
-MACHINE_END

arch/arm/mach-at91/board-ecbat91.c

@@ -1,191 +0,0 @@
-/*
- * linux/arch/arm/mach-at91rm9200/board-ecbat91.c
- * Copyright (C) 2007 emQbit.com.
- *
- * We started from board-dk.c, which is Copyright (C) 2005 SAN People.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/cpu.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ecb_at91init_early(void)
-{
-	/* Set cpu type: PQFP */
-	at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
-
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata ecb_at91eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 0,
-};
-
-static struct at91_usbh_data __initdata ecb_at91usbh_data = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct mci_platform_data __initdata ecbat91_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-
-#if defined(CONFIG_MTD_DATAFLASH)
-static struct mtd_partition __initdata my_flash0_partitions[] =
-{
-	{	/* 0x8400 */
-		.name	= "Darrell-loader",
-		.offset	= 0,
-		.size	= 12 * 1056,
-	},
-	{
-		.name	= "U-boot",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 110 * 1056,
-	},
-	{	/* 1336 (167 blocks) pages * 1056 bytes = 0x158700 bytes */
-		.name	= "UBoot-env",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 8 * 1056,
-	},
-	{	/* 1336 (167 blocks) pages * 1056 bytes = 0x158700 bytes */
-		.name	= "Kernel",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 1534 * 1056,
-	},
-	{	/* 190200 - jffs2 root filesystem */
-		.name	= "Filesystem",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,	/* 26 sectors */
-	}
-};
-
-static struct flash_platform_data __initdata my_flash0_platform = {
-	.name		= "Removable flash card",
-	.parts		= my_flash0_partitions,
-	.nr_parts	= ARRAY_SIZE(my_flash0_partitions)
-};
-
-#endif
-
-static struct spi_board_info __initdata ecb_at91spi_devices[] = {
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 10 * 1000 * 1000,
-		.bus_num	= 0,
-#if defined(CONFIG_MTD_DATAFLASH)
-		.platform_data	= &my_flash0_platform,
-#endif
-	},
-	{	/* User accessible spi - cs1 (250KHz) */
-		.modalias	= "spi-cs1",
-		.chip_select	= 1,
-		.max_speed_hz	= 250 * 1000,
-	},
-	{	/* User accessible spi - cs2 (1MHz) */
-		.modalias	= "spi-cs2",
-		.chip_select	= 2,
-		.max_speed_hz	= 1 * 1000 * 1000,
-	},
-	{	/* User accessible spi - cs3 (10MHz) */
-		.modalias	= "spi-cs3",
-		.chip_select	= 3,
-		.max_speed_hz	= 10 * 1000 * 1000,
-	},
-};
-
-/*
- * LEDs
- */
-static struct gpio_led ecb_leds[] = {
-	{	/* D1 */
-		.name			= "led1",
-		.gpio			= AT91_PIN_PC7,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-static void __init ecb_at91board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx & Tx only) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
-	at91_add_device_serial();
-
-	/* Ethernet */
-	at91_add_device_eth(&ecb_at91eth_data);
-
-	/* USB Host */
-	at91_add_device_usbh(&ecb_at91usbh_data);
-
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-
-	/* MMC */
-	at91_add_device_mci(0, &ecbat91_mci0_data);
-
-	/* SPI */
-	at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices));
-
-	/* LEDs */
-	at91_gpio_leds(ecb_leds, ARRAY_SIZE(ecb_leds));
-}
-
-MACHINE_START(ECBAT91, "emQbit's ECB_AT91")
-	/* Maintainer: emQbit.com */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ecb_at91init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ecb_at91board_init,
-MACHINE_END

arch/arm/mach-at91/board-eco920.c

@@ -1,160 +0,0 @@
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/gpio.h>
-
-#include <asm/mach-types.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-#include <mach/cpu.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init eco920_init_early(void)
-{
-	/* Set cpu type: PQFP */
-	at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
-
-	at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata eco920_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC2,
-	.is_rmii	= 1,
-};
-
-static struct at91_usbh_data __initdata eco920_usbh_data = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata eco920_udc_data = {
-	.vbus_pin	= AT91_PIN_PB12,
-	.pullup_pin	= AT91_PIN_PB13,
-};
-
-static struct mci_platform_data __initdata eco920_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 1,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-static struct physmap_flash_data eco920_flash_data = {
-	.width  = 2,
-};
-
-static struct resource eco920_flash_resource = {
-	.start          = 0x11000000,
-	.end            = 0x11ffffff,
-	.flags          = IORESOURCE_MEM,
-};
-
-static struct platform_device eco920_flash = {
-	.name           = "physmap-flash",
-	.id             = 0,
-	.dev            = {
-		.platform_data  = &eco920_flash_data,
-	},
-	.resource       = &eco920_flash_resource,
-	.num_resources  = 1,
-};
-
-static struct spi_board_info eco920_spi_devices[] = {
-	{	/* CAN controller */
-		.modalias	= "tlv5638",
-		.chip_select	= 3,
-		.max_speed_hz	= 20 * 1000 * 1000,
-		.mode		= SPI_CPHA,
-	},
-};
-
-/*
- * LEDs
- */
-static struct gpio_led eco920_leds[] = {
-	{       /* D1 */
-		.name                   = "led1",
-		.gpio                   = AT91_PIN_PB0,
-		.active_low             = 1,
-		.default_trigger        = "heartbeat",
-	},
-	{       /* D2 */
-		.name                   = "led2",
-		.gpio                   = AT91_PIN_PB1,
-		.active_low             = 1,
-		.default_trigger        = "timer",
-	}
-};
-
-static void __init eco920_board_init(void)
-{
-	/* DBGU on ttyS0. (Rx & Tx only */
-	at91_register_uart(0, 0, 0);
-	at91_add_device_serial();
-	at91_add_device_eth(&eco920_eth_data);
-	at91_add_device_usbh(&eco920_usbh_data);
-	at91_add_device_udc(&eco920_udc_data);
-
-	at91_add_device_mci(0, &eco920_mci0_data);
-	platform_device_register(&eco920_flash);
-
-	at91_ramc_write(0, AT91_SMC_CSR(7),	AT91_SMC_RWHOLD_(1)
-				| AT91_SMC_RWSETUP_(1)
-				| AT91_SMC_DBW_8
-				| AT91_SMC_WSEN
-				| AT91_SMC_NWS_(15));
-
-	at91_set_A_periph(AT91_PIN_PC6, 1);
-
-	at91_set_gpio_input(AT91_PIN_PA23, 0);
-	at91_set_deglitch(AT91_PIN_PA23, 1);
-
-/* Initialization of the Static Memory Controller for Chip Select 3 */
-	at91_ramc_write(0, AT91_SMC_CSR(3),
-		AT91_SMC_DBW_16  |	/* 16 bit */
-		AT91_SMC_WSEN    |
-		AT91_SMC_NWS_(5) |	/* wait states */
-		AT91_SMC_TDF_(1)	/* float time */
-	);
-
-	at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices));
-	/* LEDs */
-	at91_gpio_leds(eco920_leds, ARRAY_SIZE(eco920_leds));
-}
-
-MACHINE_START(ECO920, "eco920")
-	/* Maintainer: Sascha Hauer */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= eco920_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= eco920_board_init,
-MACHINE_END

arch/arm/mach-at91/board-flexibity.c

@@ -1,171 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-flexibity.c
- *
- *  Copyright (C) 2010-2011 Flexibity
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2006 Atmel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/input.h>
-#include <linux/gpio.h>
-
-#include <asm/mach-types.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-static void __init flexibity_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/* USB Host port */
-static struct at91_usbh_data __initdata flexibity_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/* USB Device port */
-static struct at91_udc_data __initdata flexibity_udc_data = {
-	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-/* I2C devices */
-static struct i2c_board_info __initdata flexibity_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("ds1307", 0x68),
-	},
-};
-
-/* SPI devices */
-static struct spi_board_info flexibity_spi_devices[] = {
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-};
-
-/* MCI (SD/MMC) */
-static struct mci_platform_data __initdata flexibity_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PC9,
-		.wp_pin		= AT91_PIN_PC4,
-	},
-};
-
-/* LEDs */
-static struct gpio_led flexibity_leds[] = {
-	{
-		.name			= "usb1:green",
-		.gpio			= AT91_PIN_PA12,
-		.active_low		= 1,
-		.default_trigger	= "default-on",
-	},
-	{
-		.name			= "usb1:red",
-		.gpio			= AT91_PIN_PA13,
-		.active_low		= 1,
-		.default_trigger	= "default-on",
-	},
-	{
-		.name			= "usb2:green",
-		.gpio			= AT91_PIN_PB26,
-		.active_low		= 1,
-		.default_trigger	= "default-on",
-	},
-	{
-		.name			= "usb2:red",
-		.gpio			= AT91_PIN_PB27,
-		.active_low		= 1,
-		.default_trigger	= "default-on",
-	},
-	{
-		.name			= "usb3:green",
-		.gpio			= AT91_PIN_PC8,
-		.active_low		= 1,
-		.default_trigger	= "default-on",
-	},
-	{
-		.name			= "usb3:red",
-		.gpio			= AT91_PIN_PC6,
-		.active_low		= 1,
-		.default_trigger	= "default-on",
-	},
-	{
-		.name			= "usb4:green",
-		.gpio			= AT91_PIN_PB4,
-		.active_low		= 1,
-		.default_trigger	= "default-on",
-	},
-	{
-		.name			= "usb4:red",
-		.gpio			= AT91_PIN_PB5,
-		.active_low		= 1,
-		.default_trigger	= "default-on",
-	}
-};
-
-static void __init flexibity_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&flexibity_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&flexibity_udc_data);
-	/* I2C */
-	at91_add_device_i2c(flexibity_i2c_devices,
-		ARRAY_SIZE(flexibity_i2c_devices));
-	/* SPI */
-	at91_add_device_spi(flexibity_spi_devices,
-		ARRAY_SIZE(flexibity_spi_devices));
-	/* MMC */
-	at91_add_device_mci(0, &flexibity_mci0_data);
-	/* LEDs */
-	at91_gpio_leds(flexibity_leds, ARRAY_SIZE(flexibity_leds));
-}
-
-MACHINE_START(FLEXIBITY, "Flexibity Connect")
-	/* Maintainer: Maxim Osipov */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= flexibity_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= flexibity_board_init,
-MACHINE_END

arch/arm/mach-at91/board-gsia18s.c

@@ -1,585 +0,0 @@
-/*
- *  Copyright (C) 2010 Christian Glindkamp <christian.glindkamp@taskit.de>
- *                     taskit GmbH
- *                2010 Igor Plyatov <plyatov@gmail.com>
- *                     GeoSIG Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/w1-gpio.h>
-#include <linux/i2c.h>
-#include <linux/i2c/pcf857x.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <mach/at91sam9_smc.h>
-#include <mach/hardware.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gsia18s.h"
-#include "stamp9g20.h"
-#include "gpio.h"
-
-static void __init gsia18s_init_early(void)
-{
-	stamp9g20_init_early();
-}
-
-/*
- * Two USB Host ports
- */
-static struct at91_usbh_data __initdata usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata udc_data = {
-	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA28,
-	.is_rmii	= 1,
-};
-
-/*
- * LEDs and GPOs
- */
-static struct gpio_led gpio_leds[] = {
-	{
-		.name			= "gpo:spi1reset",
-		.gpio			= AT91_PIN_PC1,
-		.active_low		= 0,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{
-		.name			= "gpo:trig_net_out",
-		.gpio			= AT91_PIN_PB20,
-		.active_low		= 0,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{
-		.name			= "gpo:trig_net_dir",
-		.gpio			= AT91_PIN_PB19,
-		.active_low		= 0,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{
-		.name			= "gpo:charge_dis",
-		.gpio			= AT91_PIN_PC2,
-		.active_low		= 0,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{
-		.name			= "led:event",
-		.gpio			= AT91_PIN_PB17,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{
-		.name			= "led:lan",
-		.gpio			= AT91_PIN_PB18,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{
-		.name			= "led:error",
-		.gpio			= AT91_PIN_PB16,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_ON,
-	}
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds = {
-	.name	= "leds-gpio",
-	.id	= 0,
-	.dev	= {
-		.platform_data	= &gpio_led_info,
-	}
-};
-
-static void __init gsia18s_leds_init(void)
-{
-	platform_device_register(&leds);
-}
-
-/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */
-static struct gpio_led pcf_gpio_leds1[] = {
-	{ /* bit 0 */
-		.name			= "gpo:hdc_power",
-		.gpio			= PCF_GPIO_HDC_POWER,
-		.active_low		= 0,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{ /* bit 1 */
-		.name			= "gpo:wifi_setup",
-		.gpio			= PCF_GPIO_WIFI_SETUP,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{ /* bit 2 */
-		.name			= "gpo:wifi_enable",
-		.gpio			= PCF_GPIO_WIFI_ENABLE,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{ /* bit 3	*/
-		.name			= "gpo:wifi_reset",
-		.gpio			= PCF_GPIO_WIFI_RESET,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_ON,
-	},
-	/* bit 4 used as GPI	*/
-	{ /* bit 5 */
-		.name			= "gpo:gps_setup",
-		.gpio			= PCF_GPIO_GPS_SETUP,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{ /* bit 6 */
-		.name			= "gpo:gps_standby",
-		.gpio			= PCF_GPIO_GPS_STANDBY,
-		.active_low		= 0,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_ON,
-	},
-	{ /* bit 7 */
-		.name			= "gpo:gps_power",
-		.gpio			= PCF_GPIO_GPS_POWER,
-		.active_low		= 0,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	}
-};
-
-static struct gpio_led_platform_data pcf_gpio_led_info1 = {
-	.leds		= pcf_gpio_leds1,
-	.num_leds	= ARRAY_SIZE(pcf_gpio_leds1),
-};
-
-static struct platform_device pcf_leds1 = {
-	.name	= "leds-gpio", /* GS_IA18-CB_board */
-	.id	= 1,
-	.dev	= {
-		.platform_data	= &pcf_gpio_led_info1,
-	}
-};
-
-/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */
-static struct gpio_led pcf_gpio_leds2[] = {
-	{ /* bit 0 */
-		.name			= "gpo:alarm_1",
-		.gpio			= PCF_GPIO_ALARM1,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{ /* bit 1 */
-		.name			= "gpo:alarm_2",
-		.gpio			= PCF_GPIO_ALARM2,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{ /* bit 2 */
-		.name			= "gpo:alarm_3",
-		.gpio			= PCF_GPIO_ALARM3,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{ /* bit 3 */
-		.name			= "gpo:alarm_4",
-		.gpio			= PCF_GPIO_ALARM4,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-	/* bits 4, 5, 6 not used */
-	{ /* bit 7 */
-		.name			= "gpo:alarm_v_relay_on",
-		.gpio			= PCF_GPIO_ALARM_V_RELAY_ON,
-		.active_low		= 0,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-};
-
-static struct gpio_led_platform_data pcf_gpio_led_info2 = {
-	.leds		= pcf_gpio_leds2,
-	.num_leds	= ARRAY_SIZE(pcf_gpio_leds2),
-};
-
-static struct platform_device pcf_leds2 = {
-	.name	= "leds-gpio",
-	.id	= 2,
-	.dev	= {
-		.platform_data	= &pcf_gpio_led_info2,
-	}
-};
-
-/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */
-static struct gpio_led pcf_gpio_leds3[] = {
-	{ /* bit 0 */
-		.name			= "gpo:modem_power",
-		.gpio			= PCF_GPIO_MODEM_POWER,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
-	},
-		/* bits 1 and 2 not used */
-	{ /* bit 3 */
-		.name			= "gpo:modem_reset",
-		.gpio			= PCF_GPIO_MODEM_RESET,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_ON,
-	},
-		/* bits 4, 5 and 6 not used */
-	{ /* bit 7 */
-		.name			= "gpo:trx_reset",
-		.gpio			= PCF_GPIO_TRX_RESET,
-		.active_low		= 1,
-		.default_trigger	= "none",
-		.default_state		= LEDS_GPIO_DEFSTATE_ON,
-	}
-};
-
-static struct gpio_led_platform_data pcf_gpio_led_info3 = {
-	.leds		= pcf_gpio_leds3,
-	.num_leds	= ARRAY_SIZE(pcf_gpio_leds3),
-};
-
-static struct platform_device pcf_leds3 = {
-	.name	= "leds-gpio",
-	.id	= 3,
-	.dev	= {
-		.platform_data	= &pcf_gpio_led_info3,
-	}
-};
-
-static void __init gsia18s_pcf_leds_init(void)
-{
-	platform_device_register(&pcf_leds1);
-	platform_device_register(&pcf_leds2);
-	platform_device_register(&pcf_leds3);
-}
-
-/*
- * SPI busses.
- */
-static struct spi_board_info gsia18s_spi_devices[] = {
-	{ /* User accessible spi0, cs0 used for communication with MSP RTC */
-		.modalias	= "spidev",
-		.bus_num	= 0,
-		.chip_select	= 0,
-		.max_speed_hz	= 580000,
-		.mode		= SPI_MODE_1,
-	},
-	{ /* User accessible spi1, cs0 used for communication with int. DSP */
-		.modalias	= "spidev",
-		.bus_num	= 1,
-		.chip_select	= 0,
-		.max_speed_hz	= 5600000,
-		.mode		= SPI_MODE_0,
-	},
-	{ /* User accessible spi1, cs1 used for communication with ext. DSP */
-		.modalias	= "spidev",
-		.bus_num	= 1,
-		.chip_select	= 1,
-		.max_speed_hz	= 5600000,
-		.mode		= SPI_MODE_0,
-	},
-	{ /* User accessible spi1, cs2 used for communication with ext. DSP */
-		.modalias	= "spidev",
-		.bus_num	= 1,
-		.chip_select	= 2,
-		.max_speed_hz	= 5600000,
-		.mode		= SPI_MODE_0,
-	},
-	{ /* User accessible spi1, cs3 used for communication with ext. DSP */
-		.modalias	= "spidev",
-		.bus_num	= 1,
-		.chip_select	= 3,
-		.max_speed_hz	= 5600000,
-		.mode		= SPI_MODE_0,
-	}
-};
-
-/*
- * GPI Buttons
- */
-static struct gpio_keys_button buttons[] = {
-	{
-		.gpio		= GPIO_TRIG_NET_IN,
-		.code		= BTN_1,
-		.desc		= "TRIG_NET_IN",
-		.type		= EV_KEY,
-		.active_low	= 0,
-		.wakeup		= 1,
-	},
-	{ /* SW80 on the GS_IA18_S-MN board*/
-		.gpio		= GPIO_CARD_UNMOUNT_0,
-		.code		= BTN_2,
-		.desc		= "Card umount 0",
-		.type		= EV_KEY,
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{ /* SW79 on the GS_IA18_S-MN board*/
-		.gpio		= GPIO_CARD_UNMOUNT_1,
-		.code		= BTN_3,
-		.desc		= "Card umount 1",
-		.type		= EV_KEY,
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{ /* SW280 on the GS_IA18-CB board*/
-		.gpio		= GPIO_KEY_POWER,
-		.code		= KEY_POWER,
-		.desc		= "Power Off Button",
-		.type		= EV_KEY,
-		.active_low	= 0,
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data button_data = {
-	.buttons	= buttons,
-	.nbuttons	= ARRAY_SIZE(buttons),
-};
-
-static struct platform_device button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &button_data,
-	}
-};
-
-static void __init gsia18s_add_device_buttons(void)
-{
-	at91_set_gpio_input(GPIO_TRIG_NET_IN, 1);
-	at91_set_deglitch(GPIO_TRIG_NET_IN, 1);
-	at91_set_gpio_input(GPIO_CARD_UNMOUNT_0, 1);
-	at91_set_deglitch(GPIO_CARD_UNMOUNT_0, 1);
-	at91_set_gpio_input(GPIO_CARD_UNMOUNT_1, 1);
-	at91_set_deglitch(GPIO_CARD_UNMOUNT_1, 1);
-	at91_set_gpio_input(GPIO_KEY_POWER, 0);
-	at91_set_deglitch(GPIO_KEY_POWER, 1);
-
-	platform_device_register(&button_device);
-}
-
-/*
- * I2C
- */
-static int pcf8574x_0x20_setup(struct i2c_client *client, int gpio,
-				unsigned int ngpio, void *context)
-{
-	int status;
-
-	status = gpio_request(gpio + PCF_GPIO_ETH_DETECT, "eth_det");
-	if (status < 0) {
-		pr_err("error: can't request GPIO%d\n",
-			gpio + PCF_GPIO_ETH_DETECT);
-		return status;
-	}
-	status = gpio_direction_input(gpio + PCF_GPIO_ETH_DETECT);
-	if (status < 0) {
-		pr_err("error: can't setup GPIO%d as input\n",
-			gpio + PCF_GPIO_ETH_DETECT);
-		return status;
-	}
-	status = gpio_export(gpio + PCF_GPIO_ETH_DETECT, false);
-	if (status < 0) {
-		pr_err("error: can't export GPIO%d\n",
-			gpio + PCF_GPIO_ETH_DETECT);
-		return status;
-	}
-	status = gpio_sysfs_set_active_low(gpio + PCF_GPIO_ETH_DETECT, 1);
-	if (status < 0) {
-		pr_err("error: gpio_sysfs_set active_low(GPIO%d, 1)\n",
-			gpio + PCF_GPIO_ETH_DETECT);
-		return status;
-	}
-
-	return 0;
-}
-
-static int pcf8574x_0x20_teardown(struct i2c_client *client, int gpio,
-					unsigned ngpio, void *context)
-{
-	gpio_free(gpio + PCF_GPIO_ETH_DETECT);
-	return 0;
-}
-
-static struct pcf857x_platform_data pcf20_pdata = {
-	.gpio_base	= GS_IA18_S_PCF_GPIO_BASE0,
-	.n_latch	= (1 << 4),
-	.setup		= pcf8574x_0x20_setup,
-	.teardown	= pcf8574x_0x20_teardown,
-};
-
-static struct pcf857x_platform_data pcf22_pdata = {
-	.gpio_base	= GS_IA18_S_PCF_GPIO_BASE1,
-};
-
-static struct pcf857x_platform_data pcf24_pdata = {
-	.gpio_base	= GS_IA18_S_PCF_GPIO_BASE2,
-};
-
-static struct i2c_board_info __initdata gsia18s_i2c_devices[] = {
-	{ /* U1 on the GS_IA18-CB_V3 board */
-		I2C_BOARD_INFO("pcf8574", 0x20),
-		.platform_data = &pcf20_pdata,
-	},
-	{ /* U1 on the GS_2G_OPT1-A_V0 board (Alarm) */
-		I2C_BOARD_INFO("pcf8574", 0x22),
-		.platform_data = &pcf22_pdata,
-	},
-	{ /* U1 on the GS_2G-OPT23-A_V0 board (Modem) */
-		I2C_BOARD_INFO("pcf8574", 0x24),
-		.platform_data = &pcf24_pdata,
-	},
-	{ /* U161 on the GS_IA18_S-MN board */
-		I2C_BOARD_INFO("24c1024", 0x50),
-	},
-	{ /* U162 on the GS_IA18_S-MN board */
-		I2C_BOARD_INFO("24c01", 0x53),
-	},
-};
-
-/*
- * Compact Flash
- */
-static struct at91_cf_data __initdata gsia18s_cf1_data = {
-	.irq_pin	= AT91_PIN_PA27,
-	.det_pin	= AT91_PIN_PB30,
-	.vcc_pin	= -EINVAL,
-	.rst_pin	= AT91_PIN_PB31,
-	.chipselect	= 5,
-	.flags		= AT91_CF_TRUE_IDE,
-};
-
-/* Power Off by RTC */
-static void gsia18s_power_off(void)
-{
-	pr_notice("Power supply will be switched off automatically now or after 60 seconds without ArmDAS.\n");
-	at91_set_gpio_output(AT91_PIN_PA25, 1);
-	/* Spin to death... */
-	while (1)
-		;
-}
-
-static int __init gsia18s_power_off_init(void)
-{
-	pm_power_off = gsia18s_power_off;
-	return 0;
-}
-
-/* ---------------------------------------------------------------------------*/
-
-static void __init gsia18s_board_init(void)
-{
-	/*
-	 * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI).
-	 * Used for Internal Analog Modem.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-				ATMEL_UART_CTS | ATMEL_UART_RTS |
-				ATMEL_UART_DTR | ATMEL_UART_DSR |
-				ATMEL_UART_DCD | ATMEL_UART_RI);
-	/*
-	 * USART1 on ttyS2 (Rx, Tx, CTS, RTS).
-	 * Used for GPS or WiFi or Data stream.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-				ATMEL_UART_CTS | ATMEL_UART_RTS);
-	/*
-	 * USART2 on ttyS3 (Rx, Tx, CTS, RTS).
-	 * Used for External Modem.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US2, 3,
-				ATMEL_UART_CTS | ATMEL_UART_RTS);
-	/*
-	 * USART3 on ttyS4 (Rx, Tx, RTS).
-	 * Used for RS-485.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS);
-
-	/*
-	 * USART4 on ttyS5 (Rx, Tx).
-	 * Used for TRX433 Radio Module.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-	stamp9g20_board_init();
-	at91_add_device_usbh(&usbh_data);
-	at91_add_device_udc(&udc_data);
-	at91_add_device_eth(&macb_data);
-	gsia18s_leds_init();
-	gsia18s_pcf_leds_init();
-	gsia18s_add_device_buttons();
-	at91_add_device_i2c(gsia18s_i2c_devices,
-				ARRAY_SIZE(gsia18s_i2c_devices));
-	at91_add_device_cf(&gsia18s_cf1_data);
-	at91_add_device_spi(gsia18s_spi_devices,
-				ARRAY_SIZE(gsia18s_spi_devices));
-	gsia18s_power_off_init();
-}
-
-MACHINE_START(GSIA18S, "GS_IA18_S")
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= gsia18s_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= gsia18s_board_init,
-MACHINE_END

arch/arm/mach-at91/board-kafa.c

@@ -1,113 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-kafa.c
- *
- *  Copyright (C) 2006 Sperry-Sun
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/cpu.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init kafa_init_early(void)
-{
-	/* Set cpu type: PQFP */
-	at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
-
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata kafa_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 0,
-};
-
-static struct at91_usbh_data __initdata kafa_usbh_data = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata kafa_udc_data = {
-	.vbus_pin	= AT91_PIN_PB6,
-	.pullup_pin	= AT91_PIN_PB7,
-};
-
-/*
- * LEDs
- */
-static struct gpio_led kafa_leds[] = {
-	{	/* D1 */
-		.name			= "led1",
-		.gpio			= AT91_PIN_PB4,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	},
-};
-
-static void __init kafa_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&kafa_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&kafa_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&kafa_udc_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* SPI */
-	at91_add_device_spi(NULL, 0);
-	/* LEDs */
-	at91_gpio_leds(kafa_leds, ARRAY_SIZE(kafa_leds));
-}
-
-MACHINE_START(KAFA, "Sperry-Sun KAFA")
-	/* Maintainer: Sergei Sharonov */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= kafa_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= kafa_board_init,
-MACHINE_END

arch/arm/mach-at91/board-kb9202.c

@@ -1,159 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-kb9202.c
- *
- *  Copyright (c) 2005 kb_admin
- *  		       KwikByte, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/cpu.h>
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init kb9202_init_early(void)
-{
-	/* Set cpu type: PQFP */
-	at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
-
-	/* Initialize processor: 10 MHz crystal */
-	at91_initialize(10000000);
-}
-
-static struct macb_platform_data __initdata kb9202_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PB29,
-	.is_rmii	= 0,
-};
-
-static struct at91_usbh_data __initdata kb9202_usbh_data = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata kb9202_udc_data = {
-	.vbus_pin	= AT91_PIN_PB24,
-	.pullup_pin	= AT91_PIN_PB22,
-};
-
-static struct mci_platform_data __initdata kb9202_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PB2,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-static struct mtd_partition __initdata kb9202_nand_partition[] = {
-	{
-		.name	= "nand_fs",
-		.offset	= 0,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata kb9202_nand_data = {
-	.ale		= 22,
-	.cle		= 21,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PC29,
-	.enable_pin	= AT91_PIN_PC28,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.parts		= kb9202_nand_partition,
-	.num_parts	= ARRAY_SIZE(kb9202_nand_partition),
-};
-
-/*
- * LEDs
- */
-static struct gpio_led kb9202_leds[] = {
-	{	/* D1 */
-		.name			= "led1",
-		.gpio			= AT91_PIN_PC19,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	},
-	{	/* D2 */
-		.name			= "led2",
-		.gpio			= AT91_PIN_PC18,
-		.active_low		= 1,
-		.default_trigger	= "timer",
-	}
-};
-
-static void __init kb9202_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1 (Rx & Tx only) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
-
-	/* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
-	at91_register_uart(AT91RM9200_ID_US1, 2, 0);
-
-	/* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
-	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&kb9202_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&kb9202_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&kb9202_udc_data);
-	/* MMC */
-	at91_add_device_mci(0, &kb9202_mci0_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* SPI */
-	at91_add_device_spi(NULL, 0);
-	/* NAND */
-	at91_add_device_nand(&kb9202_nand_data);
-	/* LEDs */
-	at91_gpio_leds(kb9202_leds, ARRAY_SIZE(kb9202_leds));
-}
-
-MACHINE_START(KB9200, "KB920x")
-	/* Maintainer: KwikByte, Inc. */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= kb9202_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= kb9202_board_init,
-MACHINE_END

arch/arm/mach-at91/board-pcontrol-g20.c

@@ -1,228 +0,0 @@
-/*
- *  Copyright (C) 2010 Christian Glindkamp <christian.glindkamp@taskit.de>
- *                     taskit GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-/*
- * copied and adjusted from board-stamp9g20.c
- * by Peter Gsellmann <pgsellmann@portner-elektronik.at>
- */
-
-#include <linux/mm.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/w1-gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <mach/at91sam9_smc.h>
-#include <mach/hardware.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "stamp9g20.h"
-#include "gpio.h"
-
-
-static void __init pcontrol_g20_init_early(void)
-{
-	stamp9g20_init_early();
-}
-
-static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
-	.ncs_read_setup		= 16,
-	.nrd_setup		= 18,
-	.ncs_write_setup	= 16,
-	.nwe_setup		= 18,
-
-	.ncs_read_pulse		= 63,
-	.nrd_pulse		= 55,
-	.ncs_write_pulse	= 63,
-	.nwe_pulse		= 55,
-
-	.read_cycle		= 127,
-	.write_cycle		= 127,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-			| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_SELECT
-			| AT91_SMC_DBW_8 | AT91_SMC_PS_4
-			| AT91_SMC_TDFMODE,
-	.tdf_cycles		= 3,
-}, {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 0,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 8,
-	.nrd_pulse		= 8,
-	.ncs_write_pulse	= 5,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 8,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-			| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_SELECT
-			| AT91_SMC_DBW_16 | AT91_SMC_PS_8
-			| AT91_SMC_TDFMODE,
-	.tdf_cycles		= 1,
-} };
-
-static void __init add_device_pcontrol(void)
-{
-	/* configure chip-select 4 (IO compatible to 8051  X4 ) */
-	sam9_smc_configure(0, 4, &pcontrol_smc_config[0]);
-	/* configure chip-select 7 (FerroRAM 256KiBx16bit MR2A16A  D4 ) */
-	sam9_smc_configure(0, 7, &pcontrol_smc_config[1]);
-}
-
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata pcontrol_g20_udc_data = {
-	.vbus_pin	= AT91_PIN_PA22,	/* Detect +5V bus voltage */
-	.pullup_pin	= AT91_PIN_PA4,		/* K-state, active low */
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA28,
-	.is_rmii	= 1,
-};
-
-
-/*
- * I2C devices: eeprom and phy/switch
- */
-static struct i2c_board_info __initdata pcontrol_g20_i2c_devices[] = {
-{		/* D7  address width=2, 8KiB */
-	I2C_BOARD_INFO("24c64", 0x50)
-}, {		/* D8  address width=1, 1 byte has 32 bits! */
-	I2C_BOARD_INFO("lan9303", 0x0a)
-}, };
-
-
-/*
- * LEDs
- */
-static struct gpio_led pcontrol_g20_leds[] = {
-	{
-		.name			= "LED1",	/* red  H5 */
-		.gpio			= AT91_PIN_PB18,
-		.active_low		= 1,
-		.default_trigger	= "none",	/* supervisor */
-	}, {
-		.name			= "LED2",	/* yellow  H7 */
-		.gpio			= AT91_PIN_PB19,
-		.active_low		= 1,
-		.default_trigger	= "mmc0",	/* SD-card activity */
-	}, {
-		.name			= "LED3",	/* green  H2 */
-		.gpio			= AT91_PIN_PB20,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",	/* blinky */
-	}, {
-		.name			= "LED4",	/* red  H3 */
-		.gpio			= AT91_PIN_PC6,
-		.active_low		= 1,
-		.default_trigger	= "none",	/* connection lost */
-	}, {
-		.name			= "LED5",	/* yellow  H6 */
-		.gpio			= AT91_PIN_PC7,
-		.active_low		= 1,
-		.default_trigger	= "none",	/* unsent data */
-	}, {
-		.name			= "LED6",	/* green  H1 */
-		.gpio			= AT91_PIN_PC9,
-		.active_low		= 1,
-		.default_trigger	= "none",	/* snafu */
-	}
-};
-
-
-/*
- * SPI devices
- */
-static struct spi_board_info pcontrol_g20_spi_devices[] = {
-	{
-		.modalias	= "spidev",	/* HMI port  X4 */
-		.chip_select	= 1,
-		.max_speed_hz	= 50 * 1000 * 1000,
-		.bus_num	= 0,
-	}, {
-		.modalias	= "spidev",	/* piggyback  A2 */
-		.chip_select	= 0,
-		.max_speed_hz	= 50 * 1000 * 1000,
-		.bus_num	= 1,
-	},
-};
-
-
-static void __init pcontrol_g20_board_init(void)
-{
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
-						| ATMEL_UART_RTS);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485  X5 */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
-						| ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
-	at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
-	stamp9g20_board_init();
-	at91_add_device_usbh(&usbh_data);
-	at91_add_device_eth(&macb_data);
-	at91_add_device_i2c(pcontrol_g20_i2c_devices,
-		ARRAY_SIZE(pcontrol_g20_i2c_devices));
-	add_device_pcontrol();
-	at91_add_device_spi(pcontrol_g20_spi_devices,
-		ARRAY_SIZE(pcontrol_g20_spi_devices));
-	at91_add_device_udc(&pcontrol_g20_udc_data);
-	at91_gpio_leds(pcontrol_g20_leds,
-		ARRAY_SIZE(pcontrol_g20_leds));
-	/* piggyback  A2 */
-	at91_set_gpio_output(AT91_PIN_PB31, 1);
-}
-
-
-MACHINE_START(PCONTROL_G20, "PControl G20")
-	/* Maintainer: pgsellmann@portner-elektronik.at */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= pcontrol_g20_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= pcontrol_g20_board_init,
-MACHINE_END

arch/arm/mach-at91/board-picotux200.c

@@ -1,129 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-picotux200.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2007 Kleinhenz Elektronik GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init picotux200_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata picotux200_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 1,
-};
-
-static struct at91_usbh_data __initdata picotux200_usbh_data = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct mci_platform_data __initdata picotux200_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PB27,
-		.wp_pin		= AT91_PIN_PA17,
-	},
-};
-
-#define PICOTUX200_FLASH_BASE	AT91_CHIPSELECT_0
-#define PICOTUX200_FLASH_SIZE	SZ_4M
-
-static struct physmap_flash_data picotux200_flash_data = {
-	.width	= 2,
-};
-
-static struct resource picotux200_flash_resource = {
-	.start		= PICOTUX200_FLASH_BASE,
-	.end		= PICOTUX200_FLASH_BASE + PICOTUX200_FLASH_SIZE - 1,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device picotux200_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-				.platform_data	= &picotux200_flash_data,
-			},
-	.resource	= &picotux200_flash_resource,
-	.num_resources	= 1,
-};
-
-static void __init picotux200_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			  | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			  | ATMEL_UART_RI);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&picotux200_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&picotux200_usbh_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* MMC */
-	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mci(0, &picotux200_mci0_data);
-	/* NOR Flash */
-	platform_device_register(&picotux200_flash);
-}
-
-MACHINE_START(PICOTUX2XX, "picotux 200")
-	/* Maintainer: Kleinhenz Elektronik GmbH */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= picotux200_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= picotux200_board_init,
-MACHINE_END

arch/arm/mach-at91/board-rm9200ek.c

@@ -1,196 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-rm9200ek.c
- *
- *  Copyright (C) 2005 SAN People
- *
- *  Epson S1D framebuffer glue code is:
- *     Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata ek_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 1,
-};
-
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PD4,
-	.pullup_pin	= AT91_PIN_PD5,
-};
-
-#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
-static struct mci_platform_data __initdata ek_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PB27,
-		.wp_pin		= AT91_PIN_PA17,
-	}
-};
-#endif
-
-static struct spi_board_info ek_spi_devices[] = {
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-	},
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-	{	/* DataFlash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 3,
-		.max_speed_hz	= 15 * 1000 * 1000,
-	},
-#endif
-};
-
-static struct i2c_board_info __initdata ek_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("ics1523", 0x26),
-	},
-	{
-		I2C_BOARD_INFO("dac3550", 0x4d),
-	}
-};
-
-#define EK_FLASH_BASE	AT91_CHIPSELECT_0
-#define EK_FLASH_SIZE	SZ_8M
-
-static struct physmap_flash_data ek_flash_data = {
-	.width		= 2,
-};
-
-static struct resource ek_flash_resource = {
-	.start		= EK_FLASH_BASE,
-	.end		= EK_FLASH_BASE + EK_FLASH_SIZE - 1,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device ek_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-				.platform_data	= &ek_flash_data,
-			},
-	.resource	= &ek_flash_resource,
-	.num_resources	= 1,
-};
-
-static struct gpio_led ek_leds[] = {
-	{	/* "user led 1", DS2 */
-		.name			= "green",
-		.gpio			= AT91_PIN_PB0,
-		.active_low		= 1,
-		.default_trigger	= "mmc0",
-	},
-	{	/* "user led 2", DS4 */
-		.name			= "yellow",
-		.gpio			= AT91_PIN_PB1,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	},
-	{	/* "user led 3", DS6 */
-		.name			= "red",
-		.gpio			= AT91_PIN_PB2,
-		.active_low		= 1,
-	}
-};
-
-static void __init ek_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&ek_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	at91_set_multi_drive(ek_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
-	/* I2C */
-	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-	/* DataFlash card */
-	at91_set_gpio_output(AT91_PIN_PB22, 0);
-#else
-	/* MMC */
-	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mci(0, &ek_mci0_data);
-#endif
-	/* NOR Flash */
-	platform_device_register(&ek_flash);
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-	/* VGA */
-//	ek_add_device_video();
-}
-
-MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
-	/* Maintainer: SAN People/Atmel */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END

arch/arm/mach-at91/board-sam9-l9260.c

@@ -1,230 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-sam9-l9260.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2006 Atmel
- *  Copyright (C) 2007 Olimex Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/at91sam9_smc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-	{	/* DataFlash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-#endif
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA7,
-	.is_rmii	= 0,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name	= "Bootloader Area",
-		.offset	= 0,
-		.size	= 10 * SZ_1M,
-	},
-	{
-		.name	= "User Area",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.parts		= ek_nand_partition,
-	.num_parts	= ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata ek_mci0_data = {
-	.slot[1] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PC8,
-		.wp_pin		= AT91_PIN_PC4,
-	},
-};
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
-	{	/* D1 */
-		.name			= "led1",
-		.gpio			= AT91_PIN_PA9,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	},
-	{	/* D2 */
-		.name			= "led2",
-		.gpio			= AT91_PIN_PA6,
-		.active_low		= 1,
-		.default_trigger	= "timer",
-	}
-};
-
-static void __init ek_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* NAND */
-	ek_add_device_nand();
-	/* Ethernet */
-	at91_add_device_eth(&ek_macb_data);
-	/* MMC */
-	at91_add_device_mci(0, &ek_mci0_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-}
-
-MACHINE_START(SAM9_L9260, "Olimex SAM9-L9260")
-	/* Maintainer: Olimex */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END

arch/arm/mach-at91/board-sam9260ek.c

@@ -1,354 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-sam9260ek.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2006 Atmel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/at73c213.h>
-#include <linux/clk.h>
-#include <linux/platform_data/at24.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * Audio
- */
-static struct at73c213_board_info at73c213_data = {
-	.ssc_id		= 0,
-	.shortname	= "AT91SAM9260-EK external DAC",
-};
-
-#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
-static void __init at73c213_set_clk(struct at73c213_board_info *info)
-{
-	struct clk *pck0;
-	struct clk *plla;
-
-	pck0 = clk_get(NULL, "pck0");
-	plla = clk_get(NULL, "plla");
-
-	/* AT73C213 MCK Clock */
-	at91_set_B_periph(AT91_PIN_PC1, 0);	/* PCK0 */
-
-	clk_set_parent(pck0, plla);
-	clk_put(plla);
-
-	info->dac_clk = pck0;
-}
-#else
-static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
-#endif
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-	{	/* DataFlash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-#endif
-#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
-	{	/* AT73C213 DAC */
-		.modalias	= "at73c213",
-		.chip_select	= 0,
-		.max_speed_hz	= 10 * 1000 * 1000,
-		.bus_num	= 1,
-		.mode		= SPI_MODE_1,
-		.platform_data	= &at73c213_data,
-	},
-#endif
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA7,
-	.is_rmii	= 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name	= "Partition 1",
-		.offset	= 0,
-		.size	= SZ_256K,
-	},
-	{
-		.name	= "Partition 2",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.on_flash_bbt	= 1,
-	.parts		= ek_nand_partition,
-	.num_parts	= ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	ek_nand_data.bus_width_16 = board_have_nand_16bit();
-	/* setup bus-width (8 or 16) */
-	if (ek_nand_data.bus_width_16)
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata ek_mci0_data = {
-	.slot[1] = {
-		.bus_width	= 4,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
-	{	/* "bottom" led, green, userled1 to be defined */
-		.name			= "ds5",
-		.gpio			= AT91_PIN_PA6,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* "power" led, yellow */
-		.name			= "ds1",
-		.gpio			= AT91_PIN_PA9,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-/*
- * I2C devices
- */
-static struct at24_platform_data at24c512 = {
-	.byte_len	= SZ_512K / 8,
-	.page_size	= 128,
-	.flags		= AT24_FLAG_ADDR16,
-};
-
-static struct i2c_board_info __initdata ek_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c512", 0x50),
-		.platform_data = &at24c512,
-	},
-	/* more devices can be added using expansion connectors */
-};
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PA30,
-		.code		= BTN_3,
-		.desc		= "Button 3",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PA31,
-		.code		= BTN_4,
-		.desc		= "Button 4",
-		.active_low	= 1,
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
-	.buttons	= ek_buttons,
-	.nbuttons	= ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_button_data,
-	}
-};
-
-static void __init ek_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PA30, 1);	/* btn3 */
-	at91_set_deglitch(AT91_PIN_PA30, 1);
-	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* btn4 */
-	at91_set_deglitch(AT91_PIN_PA31, 1);
-
-	platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-
-static void __init ek_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* NAND */
-	ek_add_device_nand();
-	/* Ethernet */
-	at91_add_device_eth(&ek_macb_data);
-	/* MMC */
-	at91_add_device_mci(0, &ek_mci0_data);
-	/* I2C */
-	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
-	/* SSC (to AT73C213) */
-	at73c213_set_clk(&at73c213_data);
-	at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-	/* Push Buttons */
-	ek_add_device_buttons();
-}
-
-MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK")
-	/* Maintainer: Atmel */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END

arch/arm/mach-at91/board-sam9261ek.c

@@ -1,623 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-sam9261ek.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2006 Atmel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/spi/at73c213.h>
-#include <linux/clk.h>
-#include <linux/dm9000.h>
-#include <linux/fb.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-
-#include <video/atmel_lcdc.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * DM9000 ethernet device
- */
-#if defined(CONFIG_DM9000)
-static struct resource dm9000_resource[] = {
-	[0] = {
-		.start	= AT91_CHIPSELECT_2,
-		.end	= AT91_CHIPSELECT_2 + 3,
-		.flags	= IORESOURCE_MEM
-	},
-	[1] = {
-		.start	= AT91_CHIPSELECT_2 + 0x44,
-		.end	= AT91_CHIPSELECT_2 + 0xFF,
-		.flags	= IORESOURCE_MEM
-	},
-	[2] = {
-		.flags	= IORESOURCE_IRQ
-			| IORESOURCE_IRQ_LOWEDGE | IORESOURCE_IRQ_HIGHEDGE,
-	}
-};
-
-static struct dm9000_plat_data dm9000_platdata = {
-	.flags		= DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM,
-};
-
-static struct platform_device dm9000_device = {
-	.name		= "dm9000",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(dm9000_resource),
-	.resource	= dm9000_resource,
-	.dev		= {
-		.platform_data	= &dm9000_platdata,
-	}
-};
-
-/*
- * SMC timings for the DM9000.
- * Note: These timings were calculated for MASTER_CLOCK = 100000000 according to the DM9000 timings.
- */
-static struct sam9_smc_config __initdata dm9000_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 8,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 8,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 16,
-	.write_cycle		= 16,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
-	.tdf_cycles		= 1,
-};
-
-static void __init ek_add_device_dm9000(void)
-{
-	struct resource *r = &dm9000_resource[2];
-
-	/* Configure chip-select 2 (DM9000) */
-	sam9_smc_configure(0, 2, &dm9000_smc_config);
-
-	/* Configure Reset signal as output */
-	at91_set_gpio_output(AT91_PIN_PC10, 0);
-
-	/* Configure Interrupt pin as input, no pull-up */
-	at91_set_gpio_input(AT91_PIN_PC11, 0);
-
-	r->start = r->end = gpio_to_irq(AT91_PIN_PC11);
-	platform_device_register(&dm9000_device);
-}
-#else
-static void __init ek_add_device_dm9000(void) {}
-#endif /* CONFIG_DM9000 */
-
-
-/*
- * USB Host Port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-
-/*
- * USB Device Port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PB29,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name	= "Partition 1",
-		.offset	= 0,
-		.size	= SZ_256K,
-	},
-	{
-		.name	= "Partition 2",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 22,
-	.cle		= 21,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PC15,
-	.enable_pin	= AT91_PIN_PC14,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.on_flash_bbt	= 1,
-	.parts		= ek_nand_partition,
-	.num_parts	= ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	ek_nand_data.bus_width_16 = board_have_nand_16bit();
-	/* setup bus-width (8 or 16) */
-	if (ek_nand_data.bus_width_16)
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-/*
- * SPI related devices
- */
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-
-/*
- * ADS7846 Touchscreen
- */
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-
-static int ads7843_pendown_state(void)
-{
-	return !at91_get_gpio_value(AT91_PIN_PC2);	/* Touchscreen PENIRQ */
-}
-
-static struct ads7846_platform_data ads_info = {
-	.model			= 7843,
-	.x_min			= 150,
-	.x_max			= 3830,
-	.y_min			= 190,
-	.y_max			= 3830,
-	.vref_delay_usecs	= 100,
-	.x_plate_ohms		= 450,
-	.y_plate_ohms		= 250,
-	.pressure_max		= 15000,
-	.debounce_max		= 1,
-	.debounce_rep		= 0,
-	.debounce_tol		= (~0),
-	.get_pendown_state	= ads7843_pendown_state,
-};
-
-static void __init ek_add_device_ts(void)
-{
-	at91_set_B_periph(AT91_PIN_PC2, 1);	/* External IRQ0, with pullup */
-	at91_set_gpio_input(AT91_PIN_PA11, 1);	/* Touchscreen BUSY signal */
-}
-#else
-static void __init ek_add_device_ts(void) {}
-#endif
-
-/*
- * Audio
- */
-static struct at73c213_board_info at73c213_data = {
-	.ssc_id		= 1,
-	.shortname	= "AT91SAM9261/9G10-EK external DAC",
-};
-
-#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
-static void __init at73c213_set_clk(struct at73c213_board_info *info)
-{
-	struct clk *pck2;
-	struct clk *plla;
-
-	pck2 = clk_get(NULL, "pck2");
-	plla = clk_get(NULL, "plla");
-
-	/* AT73C213 MCK Clock */
-	at91_set_B_periph(AT91_PIN_PB31, 0);	/* PCK2 */
-
-	clk_set_parent(pck2, plla);
-	clk_put(plla);
-
-	info->dac_clk = pck2;
-}
-#else
-static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
-#endif
-
-/*
- * SPI devices
- */
-static struct spi_board_info ek_spi_devices[] = {
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-	{
-		.modalias	= "ads7846",
-		.chip_select	= 2,
-		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
-		.bus_num	= 0,
-		.platform_data	= &ads_info,
-		.irq		= NR_IRQS_LEGACY + AT91SAM9261_ID_IRQ0,
-		.controller_data = (void *) AT91_PIN_PA28,	/* CS pin */
-	},
-#endif
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-	{	/* DataFlash card - jumper (J12) configurable to CS3 or CS0 */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 3,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#elif defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
-	{	/* AT73C213 DAC */
-		.modalias	= "at73c213",
-		.chip_select	= 3,
-		.max_speed_hz	= 10 * 1000 * 1000,
-		.bus_num	= 0,
-		.mode		= SPI_MODE_1,
-		.platform_data	= &at73c213_data,
-		.controller_data = (void*) AT91_PIN_PA29,	/* default for CS3 is PA6, but it must be PA29 */
-	},
-#endif
-};
-
-#else /* CONFIG_SPI_ATMEL_* */
-/* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */
-
-/*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-static struct mci_platform_data __initdata mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-#endif /* CONFIG_SPI_ATMEL_* */
-
-
-/*
- * LCD Controller
- */
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-
-#if defined(CONFIG_FB_ATMEL_STN)
-
-/* STN */
-static struct fb_videomode at91_stn_modes[] = {
-        {
-		.name           = "SP06Q002 @ 75",
-		.refresh        = 75,
-		.xres           = 320,          .yres           = 240,
-		.pixclock       = KHZ2PICOS(1440),
-
-		.left_margin    = 1,            .right_margin   = 1,
-		.upper_margin   = 0,            .lower_margin   = 0,
-		.hsync_len      = 1,            .vsync_len      = 1,
-
-		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-		.vmode          = FB_VMODE_NONINTERLACED,
-        },
-};
-
-static struct fb_monspecs at91fb_default_stn_monspecs = {
-        .manufacturer   = "HIT",
-        .monitor        = "SP06Q002",
-
-        .modedb         = at91_stn_modes,
-        .modedb_len     = ARRAY_SIZE(at91_stn_modes),
-        .hfmin          = 15000,
-        .hfmax          = 64000,
-        .vfmin          = 50,
-        .vfmax          = 150,
-};
-
-#define AT91SAM9261_DEFAULT_STN_LCDCON2	(ATMEL_LCDC_MEMOR_LITTLE \
-					| ATMEL_LCDC_DISTYPE_STNMONO \
-					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE \
-					| ATMEL_LCDC_IFWIDTH_4 \
-					| ATMEL_LCDC_SCANMOD_SINGLE)
-
-static void at91_lcdc_stn_power_control(struct atmel_lcdfb_pdata *pdata, int on)
-{
-	/* backlight */
-	if (on) {	/* power up */
-		at91_set_gpio_value(AT91_PIN_PC14, 0);
-		at91_set_gpio_value(AT91_PIN_PC15, 0);
-	} else {	/* power down */
-		at91_set_gpio_value(AT91_PIN_PC14, 1);
-		at91_set_gpio_value(AT91_PIN_PC15, 1);
-	}
-}
-
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
-	.default_bpp			= 1,
-	.default_dmacon			= ATMEL_LCDC_DMAEN,
-	.default_lcdcon2		= AT91SAM9261_DEFAULT_STN_LCDCON2,
-	.default_monspecs		= &at91fb_default_stn_monspecs,
-	.atmel_lcdfb_power_control	= at91_lcdc_stn_power_control,
-	.guard_time			= 1,
-};
-
-#else
-
-/* TFT */
-static struct fb_videomode at91_tft_vga_modes[] = {
-	{
-	        .name           = "TX09D50VM1CCA @ 60",
-		.refresh	= 60,
-		.xres		= 240,		.yres		= 320,
-		.pixclock	= KHZ2PICOS(4965),
-
-		.left_margin	= 1,		.right_margin	= 33,
-		.upper_margin	= 1,		.lower_margin	= 0,
-		.hsync_len	= 5,		.vsync_len	= 1,
-
-		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-		.vmode		= FB_VMODE_NONINTERLACED,
-	},
-};
-
-static struct fb_monspecs at91fb_default_tft_monspecs = {
-	.manufacturer	= "HIT",
-	.monitor        = "TX09D50VM1CCA",
-
-	.modedb		= at91_tft_vga_modes,
-	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
-	.hfmin		= 15000,
-	.hfmax		= 64000,
-	.vfmin		= 50,
-	.vfmax		= 150,
-};
-
-#define AT91SAM9261_DEFAULT_TFT_LCDCON2	(ATMEL_LCDC_MEMOR_LITTLE \
-					| ATMEL_LCDC_DISTYPE_TFT    \
-					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-
-static void at91_lcdc_tft_power_control(struct atmel_lcdfb_pdata *pdata, int on)
-{
-	if (on)
-		at91_set_gpio_value(AT91_PIN_PA12, 0);	/* power up */
-	else
-		at91_set_gpio_value(AT91_PIN_PA12, 1);	/* power down */
-}
-
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
-	.lcdcon_is_backlight		= true,
-	.default_bpp			= 16,
-	.default_dmacon			= ATMEL_LCDC_DMAEN,
-	.default_lcdcon2		= AT91SAM9261_DEFAULT_TFT_LCDCON2,
-	.default_monspecs		= &at91fb_default_tft_monspecs,
-	.atmel_lcdfb_power_control	= at91_lcdc_tft_power_control,
-	.guard_time			= 1,
-};
-#endif
-
-#else
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
-#endif
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PA27,
-		.code		= BTN_0,
-		.desc		= "Button 0",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PA26,
-		.code		= BTN_1,
-		.desc		= "Button 1",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PA25,
-		.code		= BTN_2,
-		.desc		= "Button 2",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PA24,
-		.code		= BTN_3,
-		.desc		= "Button 3",
-		.active_low	= 1,
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
-	.buttons	= ek_buttons,
-	.nbuttons	= ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_button_data,
-	}
-};
-
-static void __init ek_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PA27, 1);	/* btn0 */
-	at91_set_deglitch(AT91_PIN_PA27, 1);
-	at91_set_gpio_input(AT91_PIN_PA26, 1);	/* btn1 */
-	at91_set_deglitch(AT91_PIN_PA26, 1);
-	at91_set_gpio_input(AT91_PIN_PA25, 1);	/* btn2 */
-	at91_set_deglitch(AT91_PIN_PA25, 1);
-	at91_set_gpio_input(AT91_PIN_PA24, 1);	/* btn3 */
-	at91_set_deglitch(AT91_PIN_PA24, 1);
-
-	platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
-	{	/* "bottom" led, green, userled1 to be defined */
-		.name			= "ds7",
-		.gpio			= AT91_PIN_PA14,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* "top" led, green, userled2 to be defined */
-		.name			= "ds8",
-		.gpio			= AT91_PIN_PA13,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* "power" led, yellow */
-		.name			= "ds1",
-		.gpio			= AT91_PIN_PA23,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-static void __init ek_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-	at91_add_device_serial();
-
-	if (cpu_is_at91sam9g10())
-		ek_lcdc_data.lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB;
-
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* NAND */
-	ek_add_device_nand();
-	/* DM9000 ethernet */
-	ek_add_device_dm9000();
-
-	/* spi0 and mmc/sd share the same PIO pins */
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* Touchscreen */
-	ek_add_device_ts();
-	/* SSC (to AT73C213) */
-	at73c213_set_clk(&at73c213_data);
-	at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
-#else
-	/* MMC */
-	at91_add_device_mci(0, &mci0_data);
-#endif
-	/* LCD Controller */
-	at91_add_device_lcdc(&ek_lcdc_data);
-	/* Push Buttons */
-	ek_add_device_buttons();
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-}
-
-MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK")
-	/* Maintainer: Atmel */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END
-
-MACHINE_START(AT91SAM9G10EK, "Atmel AT91SAM9G10-EK")
-	/* Maintainer: Atmel */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END

arch/arm/mach-at91/board-sam9263ek.c

@@ -1,493 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-sam9263ek.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2007 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/platform_data/at24.h>
-#include <linux/fb.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/leds.h>
-#include <linux/pwm.h>
-#include <linux/leds_pwm.h>
-
-#include <video/atmel_lcdc.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 16.367 MHz crystal */
-	at91_initialize(16367660);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
-	.vbus_pin_active_low = {1, 1},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * ADS7846 Touchscreen
- */
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-static int ads7843_pendown_state(void)
-{
-	return !at91_get_gpio_value(AT91_PIN_PA15);	/* Touchscreen PENIRQ */
-}
-
-static struct ads7846_platform_data ads_info = {
-	.model			= 7843,
-	.x_min			= 150,
-	.x_max			= 3830,
-	.y_min			= 190,
-	.y_max			= 3830,
-	.vref_delay_usecs	= 100,
-	.x_plate_ohms		= 450,
-	.y_plate_ohms		= 250,
-	.pressure_max		= 15000,
-	.debounce_max		= 1,
-	.debounce_rep		= 0,
-	.debounce_tol		= (~0),
-	.get_pendown_state	= ads7843_pendown_state,
-};
-
-static void __init ek_add_device_ts(void)
-{
-	at91_set_B_periph(AT91_PIN_PA15, 1);	/* External IRQ1, with pullup */
-	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* Touchscreen BUSY signal */
-}
-#else
-static void __init ek_add_device_ts(void) {}
-#endif
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-	{	/* DataFlash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-	{
-		.modalias	= "ads7846",
-		.chip_select	= 3,
-		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
-		.bus_num	= 0,
-		.platform_data	= &ads_info,
-		.irq		= NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
-	},
-#endif
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata mci1_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PE18,
-		.wp_pin		= AT91_PIN_PE19,
-	},
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PE31,
-	.is_rmii	= 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name	= "Partition 1",
-		.offset	= 0,
-		.size	= SZ_64M,
-	},
-	{
-		.name	= "Partition 2",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PA22,
-	.enable_pin	= AT91_PIN_PD15,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.on_flash_bbt	= 1,
-	.parts		= ek_nand_partition,
-	.num_parts	= ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	ek_nand_data.bus_width_16 = board_have_nand_16bit();
-	/* setup bus-width (8 or 16) */
-	if (ek_nand_data.bus_width_16)
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- * I2C devices
- */
-static struct at24_platform_data at24c512 = {
-	.byte_len	= SZ_512K / 8,
-	.page_size	= 128,
-	.flags		= AT24_FLAG_ADDR16,
-};
-
-
-static struct i2c_board_info __initdata ek_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c512", 0x50),
-		.platform_data = &at24c512,
-	},
-	/* more devices can be added using expansion connectors */
-};
-
-/*
- * LCD Controller
- */
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static struct fb_videomode at91_tft_vga_modes[] = {
-	{
-		.name		= "TX09D50VM1CCA @ 60",
-		.refresh	= 60,
-		.xres		= 240,		.yres		= 320,
-		.pixclock	= KHZ2PICOS(4965),
-
-		.left_margin	= 1,		.right_margin	= 33,
-		.upper_margin	= 1,		.lower_margin	= 0,
-		.hsync_len	= 5,		.vsync_len	= 1,
-
-		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-		.vmode		= FB_VMODE_NONINTERLACED,
-	},
-};
-
-static struct fb_monspecs at91fb_default_monspecs = {
-	.manufacturer	= "HIT",
-	.monitor	= "TX09D70VM1CCA",
-
-	.modedb		= at91_tft_vga_modes,
-	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
-	.hfmin		= 15000,
-	.hfmax		= 64000,
-	.vfmin		= 50,
-	.vfmax		= 150,
-};
-
-#define AT91SAM9263_DEFAULT_LCDCON2 	(ATMEL_LCDC_MEMOR_LITTLE \
-					| ATMEL_LCDC_DISTYPE_TFT \
-					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-
-static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
-{
-	at91_set_gpio_value(AT91_PIN_PA30, on);
-}
-
-/* Driver datas */
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
-	.lcdcon_is_backlight		= true,
-	.default_bpp			= 16,
-	.default_dmacon			= ATMEL_LCDC_DMAEN,
-	.default_lcdcon2		= AT91SAM9263_DEFAULT_LCDCON2,
-	.default_monspecs		= &at91fb_default_monspecs,
-	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
-	.guard_time			= 1,
-};
-
-#else
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
-#endif
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
-	{	/* BP1, "leftclic" */
-		.code		= BTN_LEFT,
-		.gpio		= AT91_PIN_PC5,
-		.active_low	= 1,
-		.desc		= "left_click",
-		.wakeup		= 1,
-	},
-	{	/* BP2, "rightclic" */
-		.code		= BTN_RIGHT,
-		.gpio		= AT91_PIN_PC4,
-		.active_low	= 1,
-		.desc		= "right_click",
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
-	.buttons	= ek_buttons,
-	.nbuttons	= ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_button_data,
-	}
-};
-
-static void __init ek_add_device_buttons(void)
-{
-	at91_set_GPIO_periph(AT91_PIN_PC5, 1);	/* left button */
-	at91_set_deglitch(AT91_PIN_PC5, 1);
-	at91_set_GPIO_periph(AT91_PIN_PC4, 1);	/* right button */
-	at91_set_deglitch(AT91_PIN_PC4, 1);
-
-	platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-
-/*
- * AC97
- * reset_pin is not connected: NRST
- */
-static struct ac97c_platform_data ek_ac97_data = {
-	.reset_pin	= -EINVAL,
-};
-
-
-/*
- * LEDs ... these could all be PWM-driven, for variable brightness
- */
-static struct gpio_led ek_leds[] = {
-	{	/* "right" led, green, userled2 (could be driven by pwm2) */
-		.name			= "ds2",
-		.gpio			= AT91_PIN_PC29,
-		.active_low		= 1,
-		.default_trigger	= "nand-disk",
-	},
-	{	/* "power" led, yellow (could be driven by pwm0) */
-		.name			= "ds3",
-		.gpio			= AT91_PIN_PB7,
-		.default_trigger	= "heartbeat",
-	},
-#if !IS_ENABLED(CONFIG_LEDS_PWM)
-	{
-		.name			= "ds1",
-		.gpio			= AT91_PIN_PB8,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	}
-#endif
-};
-
-/*
- * PWM Leds
- */
-static struct pwm_lookup pwm_lookup[] = {
-	PWM_LOOKUP("at91sam9rl-pwm", 1, "leds_pwm", "ds1",
-		   5000, PWM_POLARITY_INVERSED),
-};
-
-#if IS_ENABLED(CONFIG_LEDS_PWM)
-static struct led_pwm pwm_leds[] = {
-	{
-		.name = "ds1",
-		.max_brightness = 255,
-	},
-};
-
-static struct led_pwm_platform_data pwm_data = {
-	.num_leds       = ARRAY_SIZE(pwm_leds),
-	.leds           = pwm_leds,
-};
-
-static struct platform_device leds_pwm = {
-	.name   = "leds_pwm",
-	.id     = -1,
-	.dev    = {
-		.platform_data = &pwm_data,
-	},
-};
-#endif
-
-
-/*
- * CAN
- */
-static void sam9263ek_transceiver_switch(int on)
-{
-	if (on) {
-		at91_set_gpio_output(AT91_PIN_PA18, 1); /* CANRXEN */
-		at91_set_gpio_output(AT91_PIN_PA19, 0); /* CANRS */
-	} else {
-		at91_set_gpio_output(AT91_PIN_PA18, 0); /* CANRXEN */
-		at91_set_gpio_output(AT91_PIN_PA19, 1); /* CANRS */
-	}
-}
-
-static struct at91_can_data ek_can_data = {
-	.transceiver_switch = sam9263ek_transceiver_switch,
-};
-
-static struct platform_device *devices[] __initdata = {
-#if IS_ENABLED(CONFIG_LEDS_PWM)
-	&leds_pwm,
-#endif
-};
-
-static void __init ek_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	/* SPI */
-	at91_set_gpio_output(AT91_PIN_PE20, 1);		/* select spi0 clock */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* Touchscreen */
-	ek_add_device_ts();
-	/* MMC */
-	at91_add_device_mci(1, &mci1_data);
-	/* Ethernet */
-	at91_add_device_eth(&ek_macb_data);
-	/* NAND */
-	ek_add_device_nand();
-	/* I2C */
-	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
-	/* LCD Controller */
-	at91_add_device_lcdc(&ek_lcdc_data);
-	/* Push Buttons */
-	ek_add_device_buttons();
-	/* AC97 */
-	at91_add_device_ac97(&ek_ac97_data);
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-	pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
-#if IS_ENABLED(CONFIG_LEDS_PWM)
-	at91_add_device_pwm(1 << AT91_PWM1);
-#endif
-	/* CAN */
-	at91_add_device_can(&ek_can_data);
-	/* Other platform devices */
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
-	/* Maintainer: Atmel */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END

arch/arm/mach-at91/board-sam9g20ek.c

@@ -1,429 +0,0 @@
-/*
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2008 Atmel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/at73c213.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/clk.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/consumer.h>
-
-#include <linux/platform_data/at91_adc.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-/*
- * board revision encoding
- * bit 0:
- * 	0 => 1 sd/mmc slot
- * 	1 => 2 sd/mmc slots connectors (board from revision C)
- */
-#define HAVE_2MMC	(1 << 0)
-static int inline ek_have_2mmc(void)
-{
-	return machine_is_at91sam9g20ek_2mmc() || (system_rev & HAVE_2MMC);
-}
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-	{	/* DataFlash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-#endif
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA7,
-	.is_rmii	= 1,
-};
-
-static void __init ek_add_device_macb(void)
-{
-	if (ek_have_2mmc())
-		ek_macb_data.phy_irq_pin = AT91_PIN_PB0;
-
-	at91_add_device_eth(&ek_macb_data);
-}
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name   = "Bootstrap",
-		.offset = 0,
-		.size   = 4 * SZ_1M,
-	},
-	{
-		.name	= "Partition 1",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 60 * SZ_1M,
-	},
-	{
-		.name	= "Partition 2",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-/* det_pin is not connected */
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.det_pin	= -EINVAL,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.on_flash_bbt	= 1,
-	.parts		= ek_nand_partition,
-	.num_parts	= ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 3,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	ek_nand_data.bus_width_16 = board_have_nand_16bit();
-	/* setup bus-width (8 or 16) */
-	if (ek_nand_data.bus_width_16)
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- * MCI (SD/MMC)
- * wp_pin and vcc_pin are not connected
- */
-static struct mci_platform_data __initdata ek_mmc_data = {
-	.slot[1] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PC9,
-		.wp_pin		= -EINVAL,
-	},
-
-};
-
-static void __init ek_add_device_mmc(void)
-{
-	if (ek_have_2mmc()) {
-		ek_mmc_data.slot[0].bus_width = 4;
-		ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
-		ek_mmc_data.slot[0].wp_pin = -1;
-	}
-	at91_add_device_mci(0, &ek_mmc_data);
-}
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
-	{	/* "bottom" led, green, userled1 to be defined */
-		.name			= "ds5",
-		.gpio			= AT91_PIN_PA6,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* "power" led, yellow */
-		.name			= "ds1",
-		.gpio			= AT91_PIN_PA9,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-static void __init ek_add_device_gpio_leds(void)
-{
-	if (ek_have_2mmc()) {
-		ek_leds[0].gpio = AT91_PIN_PB8;
-		ek_leds[1].gpio = AT91_PIN_PB9;
-	}
-
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-}
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PA30,
-		.code		= BTN_3,
-		.desc		= "Button 3",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PA31,
-		.code		= BTN_4,
-		.desc		= "Button 4",
-		.active_low	= 1,
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
-	.buttons	= ek_buttons,
-	.nbuttons	= ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_button_data,
-	}
-};
-
-static void __init ek_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PA30, 1);	/* btn3 */
-	at91_set_deglitch(AT91_PIN_PA30, 1);
-	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* btn4 */
-	at91_set_deglitch(AT91_PIN_PA31, 1);
-
-	platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-/*
- * ADCs
- */
-
-static struct at91_adc_data ek_adc_data = {
-	.channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3),
-	.use_external_triggers = true,
-	.vref = 3300,
-};
-
-#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
-static struct regulator_consumer_supply ek_audio_consumer_supplies[] = {
-	REGULATOR_SUPPLY("AVDD", "0-001b"),
-	REGULATOR_SUPPLY("HPVDD", "0-001b"),
-	REGULATOR_SUPPLY("DBVDD", "0-001b"),
-	REGULATOR_SUPPLY("DCVDD", "0-001b"),
-};
-
-static struct regulator_init_data ek_avdd_reg_init_data = {
-	.constraints	= {
-		.name	= "3V3",
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-	},
-	.consumer_supplies = ek_audio_consumer_supplies,
-	.num_consumer_supplies = ARRAY_SIZE(ek_audio_consumer_supplies),
-};
-
-static struct fixed_voltage_config ek_vdd_pdata = {
-	.supply_name	= "board-3V3",
-	.microvolts	= 3300000,
-	.gpio		= -EINVAL,
-	.enabled_at_boot = 0,
-	.init_data	= &ek_avdd_reg_init_data,
-};
-static struct platform_device ek_voltage_regulator = {
-	.name		= "reg-fixed-voltage",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_vdd_pdata,
-	},
-};
-static void __init ek_add_regulators(void)
-{
-	platform_device_register(&ek_voltage_regulator);
-}
-#else
-static void __init ek_add_regulators(void) {}
-#endif
-
-
-static struct i2c_board_info __initdata ek_i2c_devices[] = {
-        {
-                I2C_BOARD_INFO("24c512", 0x50)
-        },
-        {
-                I2C_BOARD_INFO("wm8731", 0x1b)
-        },
-};
-
-static struct platform_device sam9g20ek_audio_device = {
-	.name   = "at91sam9g20ek-audio",
-	.id     = -1,
-};
-
-static void __init ek_add_device_audio(void)
-{
-	platform_device_register(&sam9g20ek_audio_device);
-}
-
-
-static void __init ek_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* NAND */
-	ek_add_device_nand();
-	/* Ethernet */
-	ek_add_device_macb();
-	/* Regulators */
-	ek_add_regulators();
-	/* MMC */
-	ek_add_device_mmc();
-	/* I2C */
-	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
-	/* LEDs */
-	ek_add_device_gpio_leds();
-	/* Push Buttons */
-	ek_add_device_buttons();
-	/* ADCs */
-	at91_add_device_adc(&ek_adc_data);
-	/* PCK0 provides MCLK to the WM8731 */
-	at91_set_B_periph(AT91_PIN_PC1, 0);
-	/* SSC (for WM8731) */
-	at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
-	ek_add_device_audio();
-}
-
-MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK")
-	/* Maintainer: Atmel */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END
-
-MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod")
-	/* Maintainer: Atmel */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END

arch/arm/mach-at91/board-snapper9260.c

@@ -1,191 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-snapper9260.c
- *
- *  Copyright (C) 2010 Bluewater System Ltd
- *
- * Author: Andre Renaud <andre@bluewatersys.com>
- * Author: Ryan Mallon
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- */
-
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/platform_data/pca953x.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-#define SNAPPER9260_IO_EXP_GPIO(x)	(NR_BUILTIN_GPIO + (x))
-
-static void __init snapper9260_init_early(void)
-{
-	at91_initialize(18432000);
-}
-
-static struct at91_usbh_data __initdata snapper9260_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata snapper9260_udc_data = {
-	.vbus_pin		= SNAPPER9260_IO_EXP_GPIO(5),
-	.vbus_active_low	= 1,
-	.vbus_polled		= 1,
-	.pullup_pin		= -EINVAL,
-};
-
-static struct macb_platform_data snapper9260_macb_data = {
-	.phy_irq_pin	= -EINVAL,
-	.is_rmii	= 1,
-};
-
-static struct mtd_partition __initdata snapper9260_nand_partitions[] = {
-	{
-		.name	= "Preboot",
-		.offset	= 0,
-		.size	= SZ_128K,
-	},
-	{
-		.name	= "Bootloader",
-		.offset	= MTDPART_OFS_APPEND,
-		.size	= SZ_256K,
-	},
-	{
-		.name	= "Environment",
-		.offset	= MTDPART_OFS_APPEND,
-		.size	= SZ_128K,
-	},
-	{
-		.name	= "Kernel",
-		.offset	= MTDPART_OFS_APPEND,
-		.size	= SZ_4M,
-	},
-	{
-		.name	= "Filesystem",
-		.offset	= MTDPART_OFS_APPEND,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata snapper9260_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC13,
-	.parts		= snapper9260_nand_partitions,
-	.num_parts	= ARRAY_SIZE(snapper9260_nand_partitions),
-	.bus_width_16	= 0,
-	.enable_pin	= -EINVAL,
-	.det_pin	= -EINVAL,
-	.ecc_mode	= NAND_ECC_SOFT,
-};
-
-static struct sam9_smc_config __initdata snapper9260_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 0,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 0,
-
-	.ncs_read_pulse		= 5,
-	.nrd_pulse		= 2,
-	.ncs_write_pulse	= 5,
-	.nwe_pulse		= 2,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= (AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
-				   AT91_SMC_EXNWMODE_DISABLE),
-	.tdf_cycles		= 1,
-};
-
-static struct pca953x_platform_data snapper9260_io_expander_data = {
-	.gpio_base		= SNAPPER9260_IO_EXP_GPIO(0),
-};
-
-static struct i2c_board_info __initdata snapper9260_i2c_devices[] = {
-	{
-		/* IO expander */
-		I2C_BOARD_INFO("max7312", 0x28),
-		.platform_data = &snapper9260_io_expander_data,
-	},
-	{
-		/* Audio codec */
-		I2C_BOARD_INFO("tlv320aic23", 0x1a),
-	},
-};
-
-static struct i2c_board_info __initdata snapper9260_i2c_isl1208 = {
-		/* RTC */
-		I2C_BOARD_INFO("isl1208", 0x6f),
-};
-
-static void __init snapper9260_add_device_nand(void)
-{
-	at91_set_A_periph(AT91_PIN_PC14, 0);
-	sam9_smc_configure(0, 3, &snapper9260_nand_smc_config);
-	at91_add_device_nand(&snapper9260_nand_data);
-}
-
-static void __init snapper9260_board_init(void)
-{
-	at91_register_devices();
-
-	at91_add_device_i2c(snapper9260_i2c_devices,
-			    ARRAY_SIZE(snapper9260_i2c_devices));
-
-	snapper9260_i2c_isl1208.irq = gpio_to_irq(AT91_PIN_PA31);
-	i2c_register_board_info(0, &snapper9260_i2c_isl1208, 1);
-
-	/* Debug on ttyS0 */
-	at91_register_uart(0, 0, 0);
-
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-			   ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-			   ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
-	at91_add_device_serial();
-	at91_add_device_usbh(&snapper9260_usbh_data);
-	at91_add_device_udc(&snapper9260_udc_data);
-	at91_add_device_eth(&snapper9260_macb_data);
-	at91_add_device_ssc(AT91SAM9260_ID_SSC, (ATMEL_SSC_TF | ATMEL_SSC_TK |
-						 ATMEL_SSC_TD | ATMEL_SSC_RD));
-	snapper9260_add_device_nand();
-}
-
-MACHINE_START(SNAPPER_9260, "Bluewater Systems Snapper 9260/9G20 module")
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= snapper9260_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= snapper9260_board_init,
-MACHINE_END
-
-

arch/arm/mach-at91/board-stamp9g20.c

@@ -1,294 +0,0 @@
-/*
- *  Copyright (C) 2010 Christian Glindkamp <christian.glindkamp@taskit.de>
- *                     taskit GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/mm.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/w1-gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <mach/at91sam9_smc.h>
-#include <mach/hardware.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-void __init stamp9g20_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * NAND flash
- */
-static struct atmel_nand_data __initdata nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.bus_width_16	= 0,
-	.det_pin	= -EINVAL,
-	.ecc_mode	= NAND_ECC_SOFT,
-};
-
-static struct sam9_smc_config __initdata nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 3,
-};
-
-static void __init add_device_nand(void)
-{
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &nand_smc_config);
-
-	at91_add_device_nand(&nand_data);
-}
-
-
-/*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-static struct mci_platform_data __initdata mmc_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= -1,
-		.wp_pin		= -1,
-	},
-};
-
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata portuxg20_udc_data = {
-	.vbus_pin	= AT91_PIN_PC7,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
-	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA28,
-	.is_rmii	= 1,
-};
-
-
-/*
- * LEDs
- */
-static struct gpio_led portuxg20_leds[] = {
-	{
-		.name			= "LED2",
-		.gpio			= AT91_PIN_PC5,
-		.default_trigger	= "none",
-	}, {
-		.name			= "LED3",
-		.gpio			= AT91_PIN_PC4,
-		.default_trigger	= "none",
-	}, {
-		.name			= "LED4",
-		.gpio			= AT91_PIN_PC10,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-static struct gpio_led stamp9g20evb_leds[] = {
-	{
-		.name			= "D8",
-		.gpio			= AT91_PIN_PB18,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	}, {
-		.name			= "D9",
-		.gpio			= AT91_PIN_PB19,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	}, {
-		.name			= "D10",
-		.gpio			= AT91_PIN_PB20,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-
-/*
- * SPI devices
- */
-static struct spi_board_info portuxg20_spi_devices[] = {
-	{
-		.modalias	= "spidev",
-		.chip_select	= 0,
-		.max_speed_hz	= 1 * 1000 * 1000,
-		.bus_num	= 0,
-	}, {
-		.modalias	= "spidev",
-		.chip_select	= 0,
-		.max_speed_hz	= 1 * 1000 * 1000,
-		.bus_num	= 1,
-	},
-};
-
-
-/*
- * Dallas 1-Wire
- */
-static struct w1_gpio_platform_data w1_gpio_pdata = {
-	.pin		= AT91_PIN_PA29,
-	.is_open_drain	= 1,
-	.ext_pullup_enable_pin	= -EINVAL,
-};
-
-static struct platform_device w1_device = {
-	.name			= "w1-gpio",
-	.id			= -1,
-	.dev.platform_data	= &w1_gpio_pdata,
-};
-
-void add_w1(void)
-{
-	at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
-	at91_set_multi_drive(w1_gpio_pdata.pin, 1);
-	platform_device_register(&w1_device);
-}
-
-
-void __init stamp9g20_board_init(void)
-{
-	/* Serial */
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-	at91_add_device_serial();
-	/* NAND */
-	add_device_nand();
-	/* MMC */
-	at91_add_device_mci(0, &mmc_data);
-	/* W1 */
-	add_w1();
-}
-
-static void __init portuxg20_board_init(void)
-{
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-						| ATMEL_UART_DTR | ATMEL_UART_DSR
-						| ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART4 on ttyS5. (Rx, Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
-	/* USART5 on ttyS6. (Rx, Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-	stamp9g20_board_init();
-	/* USB Host */
-	at91_add_device_usbh(&usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&portuxg20_udc_data);
-	/* Ethernet */
-	at91_add_device_eth(&macb_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* SPI */
-	at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices));
-	/* LEDs */
-	at91_gpio_leds(portuxg20_leds, ARRAY_SIZE(portuxg20_leds));
-}
-
-static void __init stamp9g20evb_board_init(void)
-{
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-						| ATMEL_UART_DTR | ATMEL_UART_DSR
-						| ATMEL_UART_DCD | ATMEL_UART_RI);
-	stamp9g20_board_init();
-	/* USB Host */
-	at91_add_device_usbh(&usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&stamp9g20evb_udc_data);
-	/* Ethernet */
-	at91_add_device_eth(&macb_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* LEDs */
-	at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds));
-}
-
-MACHINE_START(PORTUXG20, "taskit PortuxG20")
-	/* Maintainer: taskit GmbH */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= stamp9g20_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= portuxg20_board_init,
-MACHINE_END
-
-MACHINE_START(STAMP9G20, "taskit Stamp9G20")
-	/* Maintainer: taskit GmbH */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= stamp9g20_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= stamp9g20evb_board_init,
-MACHINE_END

arch/arm/mach-at91/board-yl-9200.c

@@ -1,597 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-yl-9200.c
- *
- * Adapted from various board files in arch/arm/mach-at91
- *
- * Modifications for YL-9200 platform:
- *  Copyright (C) 2007 S. Birtles
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/mtd/physmap.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-#include <mach/cpu.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init yl9200_init_early(void)
-{
-	/* Set cpu type: PQFP */
-	at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
-
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * LEDs
- */
-static struct gpio_led yl9200_leds[] = {
-	{	/* D2 */
-		.name			= "led2",
-		.gpio			= AT91_PIN_PB17,
-		.active_low		= 1,
-		.default_trigger	= "timer",
-	},
-	{	/* D3 */
-		.name			= "led3",
-		.gpio			= AT91_PIN_PB16,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	},
-	{	/* D4 */
-		.name			= "led4",
-		.gpio			= AT91_PIN_PB15,
-		.active_low		= 1,
-	},
-	{	/* D5 */
-		.name			= "led5",
-		.gpio			= AT91_PIN_PB8,
-		.active_low		= 1,
-	}
-};
-
-/*
- * Ethernet
- */
-static struct macb_platform_data __initdata yl9200_eth_data = {
-	.phy_irq_pin		= AT91_PIN_PB28,
-	.is_rmii		= 1,
-};
-
-/*
- * USB Host
- */
-static struct at91_usbh_data __initdata yl9200_usbh_data = {
-	.ports			= 1,	/* PQFP version of AT91RM9200 */
-	.vbus_pin		= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device
- */
-static struct at91_udc_data __initdata yl9200_udc_data = {
-	.pullup_pin		= AT91_PIN_PC4,
-	.vbus_pin		= AT91_PIN_PC5,
-	.pullup_active_low	= 1,	/* Active Low due to PNP transistor (pg 7) */
-
-};
-
-/*
- * MMC
- */
-static struct mci_platform_data __initdata yl9200_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PB9,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-/*
- * NAND Flash
- */
-static struct mtd_partition __initdata yl9200_nand_partition[] = {
-	{
-		.name	= "AT91 NAND partition 1, boot",
-		.offset	= 0,
-		.size	= SZ_256K
-	},
-	{
-		.name	= "AT91 NAND partition 2, kernel",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= (2 * SZ_1M) - SZ_256K
-	},
-	{
-		.name	= "AT91 NAND partition 3, filesystem",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 14 * SZ_1M
-	},
-	{
-		.name	= "AT91 NAND partition 4, storage",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= SZ_16M
-	},
-	{
-		.name	= "AT91 NAND partition 5, ext-fs",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= SZ_32M
-	}
-};
-
-static struct atmel_nand_data __initdata yl9200_nand_data = {
-	.ale		= 6,
-	.cle		= 7,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PC14,	/* R/!B (Sheet10) */
-	.enable_pin	= AT91_PIN_PC15,	/* !CE  (Sheet10) */
-	.ecc_mode	= NAND_ECC_SOFT,
-	.parts		= yl9200_nand_partition,
-	.num_parts	= ARRAY_SIZE(yl9200_nand_partition),
-};
-
-/*
- * NOR Flash
- */
-#define YL9200_FLASH_BASE	AT91_CHIPSELECT_0
-#define YL9200_FLASH_SIZE	SZ_16M
-
-static struct mtd_partition yl9200_flash_partitions[] = {
-	{
-		.name		= "Bootloader",
-		.offset		= 0,
-		.size		= SZ_256K,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "Kernel",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= (2 * SZ_1M) - SZ_256K
-	},
-	{
-		.name		= "Filesystem",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= MTDPART_SIZ_FULL
-	}
-};
-
-static struct physmap_flash_data yl9200_flash_data = {
-	.width		= 2,
-	.parts		= yl9200_flash_partitions,
-	.nr_parts	= ARRAY_SIZE(yl9200_flash_partitions),
-};
-
-static struct resource yl9200_flash_resources[] = {
-	{
-		.start	= YL9200_FLASH_BASE,
-		.end	= YL9200_FLASH_BASE + YL9200_FLASH_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device yl9200_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-				.platform_data	= &yl9200_flash_data,
-			},
-	.resource	= yl9200_flash_resources,
-	.num_resources	= ARRAY_SIZE(yl9200_flash_resources),
-};
-
-/*
- * I2C (TWI)
- */
-static struct i2c_board_info __initdata yl9200_i2c_devices[] = {
-	{	/* EEPROM */
-		I2C_BOARD_INFO("24c128", 0x50),
-	}
-};
-
-/*
- * GPIO Buttons
-*/
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button yl9200_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PA24,
-		.code		= BTN_2,
-		.desc		= "SW2",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PB1,
-		.code		= BTN_3,
-		.desc		= "SW3",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PB2,
-		.code		= BTN_4,
-		.desc		= "SW4",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PB6,
-		.code		= BTN_5,
-		.desc		= "SW5",
-		.active_low	= 1,
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data yl9200_button_data = {
-	.buttons	= yl9200_buttons,
-	.nbuttons	= ARRAY_SIZE(yl9200_buttons),
-};
-
-static struct platform_device yl9200_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &yl9200_button_data,
-	}
-};
-
-static void __init yl9200_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PA24, 1);	/* SW2 */
-	at91_set_deglitch(AT91_PIN_PA24, 1);
-	at91_set_gpio_input(AT91_PIN_PB1, 1);	/* SW3 */
-	at91_set_deglitch(AT91_PIN_PB1, 1);
-	at91_set_gpio_input(AT91_PIN_PB2, 1);	/* SW4 */
-	at91_set_deglitch(AT91_PIN_PB2, 1);
-	at91_set_gpio_input(AT91_PIN_PB6, 1);	/* SW5 */
-	at91_set_deglitch(AT91_PIN_PB6, 1);
-
-	/* Enable buttons (Sheet 5) */
-	at91_set_gpio_output(AT91_PIN_PB7, 1);
-
-	platform_device_register(&yl9200_button_device);
-}
-#else
-static void __init yl9200_add_device_buttons(void) {}
-#endif
-
-/*
- * Touchscreen
- */
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-static int ads7843_pendown_state(void)
-{
-	return !at91_get_gpio_value(AT91_PIN_PB11);	/* Touchscreen PENIRQ */
-}
-
-static struct ads7846_platform_data ads_info = {
-	.model			= 7843,
-	.x_min			= 150,
-	.x_max			= 3830,
-	.y_min			= 190,
-	.y_max			= 3830,
-	.vref_delay_usecs	= 100,
-
-	/* For a 8" touch-screen */
-	// .x_plate_ohms		= 603,
-	// .y_plate_ohms		= 332,
-
-	/* For a 10.4" touch-screen */
-	// .x_plate_ohms		= 611,
-	// .y_plate_ohms		= 325,
-
-	.x_plate_ohms		= 576,
-	.y_plate_ohms		= 366,
-
-	.pressure_max		= 15000, /* generally nonsense on the 7843 */
-	.debounce_max		= 1,
-	.debounce_rep		= 0,
-	.debounce_tol		= (~0),
-	.get_pendown_state	= ads7843_pendown_state,
-};
-
-static void __init yl9200_add_device_ts(void)
-{
-	at91_set_gpio_input(AT91_PIN_PB11, 1);	/* Touchscreen interrupt pin */
-	at91_set_gpio_input(AT91_PIN_PB10, 1);	/* Touchscreen BUSY signal - not used! */
-}
-#else
-static void __init yl9200_add_device_ts(void) {}
-#endif
-
-/*
- * SPI devices
- */
-static struct spi_board_info yl9200_spi_devices[] = {
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-	{	/* Touchscreen */
-		.modalias	= "ads7846",
-		.chip_select	= 0,
-		.max_speed_hz	= 5000 * 26,
-		.platform_data	= &ads_info,
-		.irq		= AT91_PIN_PB11,
-	},
-#endif
-	{	/* CAN */
-		.modalias	= "mcp2510",
-		.chip_select	= 1,
-		.max_speed_hz	= 25000 * 26,
-		.irq		= AT91_PIN_PC0,
-	}
-};
-
-/*
- * LCD / VGA
- *
- * EPSON S1D13806 FB (discontinued chip)
- * EPSON S1D13506 FB
- */
-#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE)
-#include <video/s1d13xxxfb.h>
-
-
-static void yl9200_init_video(void)
-{
-	/* NWAIT Signal */
-	at91_set_A_periph(AT91_PIN_PC6, 0);
-
-	/* Initialization of the Static Memory Controller for Chip Select 2 */
-	at91_ramc_write(0, AT91_SMC_CSR(2), AT91_SMC_DBW_16		/* 16 bit */
-			| AT91_SMC_WSEN | AT91_SMC_NWS_(0x4)	/* wait states */
-			| AT91_SMC_TDF_(0x100)			/* float time */
-	);
-}
-
-static struct s1d13xxxfb_regval yl9200_s1dfb_initregs[] =
-{
-	{S1DREG_MISC,			0x00},	/* Miscellaneous Register*/
-	{S1DREG_COM_DISP_MODE,		0x01},	/* Display Mode Register, LCD only*/
-	{S1DREG_GPIO_CNF0,		0x00},	/* General IO Pins Configuration Register*/
-	{S1DREG_GPIO_CTL0,		0x00},	/* General IO Pins Control Register*/
-	{S1DREG_CLK_CNF,		0x11},	/* Memory Clock Configuration Register*/
-	{S1DREG_LCD_CLK_CNF,		0x10},	/* LCD Pixel Clock Configuration Register*/
-	{S1DREG_CRT_CLK_CNF,		0x12},	/* CRT/TV Pixel Clock Configuration Register*/
-	{S1DREG_MPLUG_CLK_CNF,		0x01},	/* MediaPlug Clock Configuration Register*/
-	{S1DREG_CPU2MEM_WST_SEL,	0x02},	/* CPU To Memory Wait State Select Register*/
-	{S1DREG_MEM_CNF,		0x00},	/* Memory Configuration Register*/
-	{S1DREG_SDRAM_REF_RATE,		0x04},	/* DRAM Refresh Rate Register, MCLK source*/
-	{S1DREG_SDRAM_TC0,		0x12},	/* DRAM Timings Control Register 0*/
-	{S1DREG_SDRAM_TC1,		0x02},	/* DRAM Timings Control Register 1*/
-	{S1DREG_PANEL_TYPE,		0x25},	/* Panel Type Register*/
-	{S1DREG_MOD_RATE,		0x00},	/* MOD Rate Register*/
-	{S1DREG_LCD_DISP_HWIDTH,	0x4F},	/* LCD Horizontal Display Width Register*/
-	{S1DREG_LCD_NDISP_HPER,		0x13},	/* LCD Horizontal Non-Display Period Register*/
-	{S1DREG_TFT_FPLINE_START,	0x01},	/* TFT FPLINE Start Position Register*/
-	{S1DREG_TFT_FPLINE_PWIDTH,	0x0c},	/* TFT FPLINE Pulse Width Register*/
-	{S1DREG_LCD_DISP_VHEIGHT0,	0xDF},	/* LCD Vertical Display Height Register 0*/
-	{S1DREG_LCD_DISP_VHEIGHT1,	0x01},	/* LCD Vertical Display Height Register 1*/
-	{S1DREG_LCD_NDISP_VPER,		0x2c},	/* LCD Vertical Non-Display Period Register*/
-	{S1DREG_TFT_FPFRAME_START,	0x0a},	/* TFT FPFRAME Start Position Register*/
-	{S1DREG_TFT_FPFRAME_PWIDTH,	0x02},	/* TFT FPFRAME Pulse Width Register*/
-	{S1DREG_LCD_DISP_MODE,		0x05},	/* LCD Display Mode Register*/
-	{S1DREG_LCD_MISC,		0x01},	/* LCD Miscellaneous Register*/
-	{S1DREG_LCD_DISP_START0,	0x00},	/* LCD Display Start Address Register 0*/
-	{S1DREG_LCD_DISP_START1,	0x00},	/* LCD Display Start Address Register 1*/
-	{S1DREG_LCD_DISP_START2,	0x00},	/* LCD Display Start Address Register 2*/
-	{S1DREG_LCD_MEM_OFF0,		0x80},	/* LCD Memory Address Offset Register 0*/
-	{S1DREG_LCD_MEM_OFF1,		0x02},	/* LCD Memory Address Offset Register 1*/
-	{S1DREG_LCD_PIX_PAN,		0x03},	/* LCD Pixel Panning Register*/
-	{S1DREG_LCD_DISP_FIFO_HTC,	0x00},	/* LCD Display FIFO High Threshold Control Register*/
-	{S1DREG_LCD_DISP_FIFO_LTC,	0x00},	/* LCD Display FIFO Low Threshold Control Register*/
-	{S1DREG_CRT_DISP_HWIDTH,	0x4F},	/* CRT/TV Horizontal Display Width Register*/
-	{S1DREG_CRT_NDISP_HPER,		0x13},	/* CRT/TV Horizontal Non-Display Period Register*/
-	{S1DREG_CRT_HRTC_START,		0x01},	/* CRT/TV HRTC Start Position Register*/
-	{S1DREG_CRT_HRTC_PWIDTH,	0x0B},	/* CRT/TV HRTC Pulse Width Register*/
-	{S1DREG_CRT_DISP_VHEIGHT0,	0xDF},	/* CRT/TV Vertical Display Height Register 0*/
-	{S1DREG_CRT_DISP_VHEIGHT1,	0x01},	/* CRT/TV Vertical Display Height Register 1*/
-	{S1DREG_CRT_NDISP_VPER,		0x2B},	/* CRT/TV Vertical Non-Display Period Register*/
-	{S1DREG_CRT_VRTC_START,		0x09},	/* CRT/TV VRTC Start Position Register*/
-	{S1DREG_CRT_VRTC_PWIDTH,	0x01},	/* CRT/TV VRTC Pulse Width Register*/
-	{S1DREG_TV_OUT_CTL,		0x18},	/* TV Output Control Register */
-	{S1DREG_CRT_DISP_MODE,		0x05},	/* CRT/TV Display Mode Register, 16BPP*/
-	{S1DREG_CRT_DISP_START0,	0x00},	/* CRT/TV Display Start Address Register 0*/
-	{S1DREG_CRT_DISP_START1,	0x00},	/* CRT/TV Display Start Address Register 1*/
-	{S1DREG_CRT_DISP_START2,	0x00},	/* CRT/TV Display Start Address Register 2*/
-	{S1DREG_CRT_MEM_OFF0,		0x80},	/* CRT/TV Memory Address Offset Register 0*/
-	{S1DREG_CRT_MEM_OFF1,		0x02},	/* CRT/TV Memory Address Offset Register 1*/
-	{S1DREG_CRT_PIX_PAN,		0x00},	/* CRT/TV Pixel Panning Register*/
-	{S1DREG_CRT_DISP_FIFO_HTC,	0x00},	/* CRT/TV Display FIFO High Threshold Control Register*/
-	{S1DREG_CRT_DISP_FIFO_LTC,	0x00},	/* CRT/TV Display FIFO Low Threshold Control Register*/
-	{S1DREG_LCD_CUR_CTL,		0x00},	/* LCD Ink/Cursor Control Register*/
-	{S1DREG_LCD_CUR_START,		0x01},	/* LCD Ink/Cursor Start Address Register*/
-	{S1DREG_LCD_CUR_XPOS0,		0x00},	/* LCD Cursor X Position Register 0*/
-	{S1DREG_LCD_CUR_XPOS1,		0x00},	/* LCD Cursor X Position Register 1*/
-	{S1DREG_LCD_CUR_YPOS0,		0x00},	/* LCD Cursor Y Position Register 0*/
-	{S1DREG_LCD_CUR_YPOS1,		0x00},	/* LCD Cursor Y Position Register 1*/
-	{S1DREG_LCD_CUR_BCTL0,		0x00},	/* LCD Ink/Cursor Blue Color 0 Register*/
-	{S1DREG_LCD_CUR_GCTL0,		0x00},	/* LCD Ink/Cursor Green Color 0 Register*/
-	{S1DREG_LCD_CUR_RCTL0,		0x00},	/* LCD Ink/Cursor Red Color 0 Register*/
-	{S1DREG_LCD_CUR_BCTL1,		0x1F},	/* LCD Ink/Cursor Blue Color 1 Register*/
-	{S1DREG_LCD_CUR_GCTL1,		0x3F},	/* LCD Ink/Cursor Green Color 1 Register*/
-	{S1DREG_LCD_CUR_RCTL1,		0x1F},	/* LCD Ink/Cursor Red Color 1 Register*/
-	{S1DREG_LCD_CUR_FIFO_HTC,	0x00},	/* LCD Ink/Cursor FIFO Threshold Register*/
-	{S1DREG_CRT_CUR_CTL,		0x00},	/* CRT/TV Ink/Cursor Control Register*/
-	{S1DREG_CRT_CUR_START,		0x01},	/* CRT/TV Ink/Cursor Start Address Register*/
-	{S1DREG_CRT_CUR_XPOS0,		0x00},	/* CRT/TV Cursor X Position Register 0*/
-	{S1DREG_CRT_CUR_XPOS1,		0x00},	/* CRT/TV Cursor X Position Register 1*/
-	{S1DREG_CRT_CUR_YPOS0,		0x00},	/* CRT/TV Cursor Y Position Register 0*/
-	{S1DREG_CRT_CUR_YPOS1,		0x00},	/* CRT/TV Cursor Y Position Register 1*/
-	{S1DREG_CRT_CUR_BCTL0,		0x00},	/* CRT/TV Ink/Cursor Blue Color 0 Register*/
-	{S1DREG_CRT_CUR_GCTL0,		0x00},	/* CRT/TV Ink/Cursor Green Color 0 Register*/
-	{S1DREG_CRT_CUR_RCTL0,		0x00},	/* CRT/TV Ink/Cursor Red Color 0 Register*/
-	{S1DREG_CRT_CUR_BCTL1,		0x1F},	/* CRT/TV Ink/Cursor Blue Color 1 Register*/
-	{S1DREG_CRT_CUR_GCTL1,		0x3F},	/* CRT/TV Ink/Cursor Green Color 1 Register*/
-	{S1DREG_CRT_CUR_RCTL1,		0x1F},	/* CRT/TV Ink/Cursor Red Color 1 Register*/
-	{S1DREG_CRT_CUR_FIFO_HTC,	0x00},	/* CRT/TV Ink/Cursor FIFO Threshold Register*/
-	{S1DREG_BBLT_CTL0,		0x00},	/* BitBlt Control Register 0*/
-	{S1DREG_BBLT_CTL1,		0x01},	/* BitBlt Control Register 1*/
-	{S1DREG_BBLT_CC_EXP,		0x00},	/* BitBlt ROP Code/Color Expansion Register*/
-	{S1DREG_BBLT_OP,		0x00},	/* BitBlt Operation Register*/
-	{S1DREG_BBLT_SRC_START0,	0x00},	/* BitBlt Source Start Address Register 0*/
-	{S1DREG_BBLT_SRC_START1,	0x00},	/* BitBlt Source Start Address Register 1*/
-	{S1DREG_BBLT_SRC_START2,	0x00},	/* BitBlt Source Start Address Register 2*/
-	{S1DREG_BBLT_DST_START0,	0x00},	/* BitBlt Destination Start Address Register 0*/
-	{S1DREG_BBLT_DST_START1,	0x00},	/* BitBlt Destination Start Address Register 1*/
-	{S1DREG_BBLT_DST_START2,	0x00},	/* BitBlt Destination Start Address Register 2*/
-	{S1DREG_BBLT_MEM_OFF0,		0x00},	/* BitBlt Memory Address Offset Register 0*/
-	{S1DREG_BBLT_MEM_OFF1,		0x00},	/* BitBlt Memory Address Offset Register 1*/
-	{S1DREG_BBLT_WIDTH0,		0x00},	/* BitBlt Width Register 0*/
-	{S1DREG_BBLT_WIDTH1,		0x00},	/* BitBlt Width Register 1*/
-	{S1DREG_BBLT_HEIGHT0,		0x00},	/* BitBlt Height Register 0*/
-	{S1DREG_BBLT_HEIGHT1,		0x00},	/* BitBlt Height Register 1*/
-	{S1DREG_BBLT_BGC0,		0x00},	/* BitBlt Background Color Register 0*/
-	{S1DREG_BBLT_BGC1,		0x00},	/* BitBlt Background Color Register 1*/
-	{S1DREG_BBLT_FGC0,		0x00},	/* BitBlt Foreground Color Register 0*/
-	{S1DREG_BBLT_FGC1,		0x00},	/* BitBlt Foreground Color Register 1*/
-	{S1DREG_LKUP_MODE,		0x00},	/* Look-Up Table Mode Register*/
-	{S1DREG_LKUP_ADDR,		0x00},	/* Look-Up Table Address Register*/
-	{S1DREG_PS_CNF,			0x00},	/* Power Save Configuration Register*/
-	{S1DREG_PS_STATUS,		0x00},	/* Power Save Status Register*/
-	{S1DREG_CPU2MEM_WDOGT,		0x00},	/* CPU-to-Memory Access Watchdog Timer Register*/
-	{S1DREG_COM_DISP_MODE,		0x01},	/* Display Mode Register, LCD only*/
-};
-
-static struct s1d13xxxfb_pdata yl9200_s1dfb_pdata = {
-	.initregs		= yl9200_s1dfb_initregs,
-	.initregssize		= ARRAY_SIZE(yl9200_s1dfb_initregs),
-	.platform_init_video	= yl9200_init_video,
-};
-
-#define YL9200_FB_REG_BASE	AT91_CHIPSELECT_7
-#define YL9200_FB_VMEM_BASE	YL9200_FB_REG_BASE + SZ_2M
-#define YL9200_FB_VMEM_SIZE	SZ_2M
-
-static struct resource yl9200_s1dfb_resource[] = {
-	[0] = {	/* video mem */
-		.name	= "s1d13xxxfb memory",
-		.start	= YL9200_FB_VMEM_BASE,
-		.end	= YL9200_FB_VMEM_BASE + YL9200_FB_VMEM_SIZE -1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {	/* video registers */
-		.name	= "s1d13xxxfb registers",
-		.start	= YL9200_FB_REG_BASE,
-		.end	= YL9200_FB_REG_BASE + SZ_512 -1,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static u64 s1dfb_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device yl9200_s1dfb_device = {
-	.name		= "s1d13806fb",
-	.id		= -1,
-	.dev	= {
-		.dma_mask		= &s1dfb_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data		= &yl9200_s1dfb_pdata,
-	},
-	.resource	= yl9200_s1dfb_resource,
-	.num_resources	= ARRAY_SIZE(yl9200_s1dfb_resource),
-};
-
-void __init yl9200_add_device_video(void)
-{
-	platform_device_register(&yl9200_s1dfb_device);
-}
-#else
-void __init yl9200_add_device_video(void) {}
-#endif
-
-
-static void __init yl9200_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			| ATMEL_UART_RI);
-
-	/* USART0 on ttyS2. (Rx & Tx only to JP3) */
-	at91_register_uart(AT91RM9200_ID_US0, 2, 0);
-
-	/* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
-	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&yl9200_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&yl9200_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&yl9200_udc_data);
-	/* I2C */
-	at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices));
-	/* MMC */
-	at91_add_device_mci(0, &yl9200_mci0_data);
-	/* NAND */
-	at91_add_device_nand(&yl9200_nand_data);
-	/* NOR Flash */
-	platform_device_register(&yl9200_flash);
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-	/* SPI */
-	at91_add_device_spi(yl9200_spi_devices, ARRAY_SIZE(yl9200_spi_devices));
-	/* Touchscreen */
-	yl9200_add_device_ts();
-#endif
-	/* LEDs. */
-	at91_gpio_leds(yl9200_leds, ARRAY_SIZE(yl9200_leds));
-	/* Push Buttons */
-	yl9200_add_device_buttons();
-	/* VGA */
-	yl9200_add_device_video();
-}
-
-MACHINE_START(YL9200, "uCdragon YL-9200")
-	/* Maintainer: S.Birtles */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= yl9200_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= yl9200_board_init,
-MACHINE_END

arch/arm/mach-at91/board.h

@@ -1,127 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/board.h
- *
- *  Copyright (C) 2005 HP Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-/*
- * These are data structures found in platform_device.dev.platform_data,
- * and describing board-specific data needed by drivers.  For example,
- * which pin is used for a given GPIO role.
- *
- * In 2.6, drivers should strongly avoid board-specific knowledge so
- * that supporting new boards normally won't require driver patches.
- * Most board-specific knowledge should be in arch/.../board-*.c files.
- */
-
-#ifndef __ASM_ARCH_BOARD_H
-#define __ASM_ARCH_BOARD_H
-
-#include <linux/platform_data/atmel.h>
-
- /* USB Device */
-extern void __init at91_add_device_udc(struct at91_udc_data *data);
-
- /* USB High Speed Device */
-extern void __init at91_add_device_usba(struct usba_platform_data *data);
-
- /* Compact Flash */
-extern void __init at91_add_device_cf(struct at91_cf_data *data);
-
- /* MMC / SD */
-  /* atmel-mci platform config */
-extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data);
-
-extern void __init at91_add_device_eth(struct macb_platform_data *data);
-
- /* USB Host */
-extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
-extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data);
-extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data);
-
-extern void __init at91_add_device_nand(struct atmel_nand_data *data);
-
- /* I2C*/
-#if defined(CONFIG_ARCH_AT91SAM9G45)
-extern void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices);
-#else
-extern void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices);
-#endif
-
- /* SPI */
-extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
-
- /* Serial */
-#define ATMEL_UART_CTS	0x01
-#define ATMEL_UART_RTS	0x02
-#define ATMEL_UART_DSR	0x04
-#define ATMEL_UART_DTR	0x08
-#define ATMEL_UART_DCD	0x10
-#define ATMEL_UART_RI	0x20
-
-extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
-
-extern struct platform_device *atmel_default_console_device;
-
-extern void __init at91_add_device_serial(void);
-
-/*
- * PWM
- */
-#define AT91_PWM0	0
-#define AT91_PWM1	1
-#define AT91_PWM2	2
-#define AT91_PWM3	3
-
-extern void __init at91_add_device_pwm(u32 mask);
-
-/*
- * SSC -- accessed through ssc_request(id).  Drivers don't bind to SSC
- * platform devices.  Their SSC ID is part of their configuration data,
- * along with information about which SSC signals they should use.
- */
-#define ATMEL_SSC_TK	0x01
-#define ATMEL_SSC_TF	0x02
-#define ATMEL_SSC_TD	0x04
-#define ATMEL_SSC_TX	(ATMEL_SSC_TK | ATMEL_SSC_TF | ATMEL_SSC_TD)
-
-#define ATMEL_SSC_RK	0x10
-#define ATMEL_SSC_RF	0x20
-#define ATMEL_SSC_RD	0x40
-#define ATMEL_SSC_RX	(ATMEL_SSC_RK | ATMEL_SSC_RF | ATMEL_SSC_RD)
-
-extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
-
- /* LCD Controller */
-struct atmel_lcdfb_pdata;
-extern void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data);
-
- /* AC97 */
-extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
-
- /* ISI */
-struct isi_platform_data;
-extern void __init at91_add_device_isi(struct isi_platform_data *data,
-		bool use_pck_as_mck);
-
-/* CAN */
-extern void __init at91_add_device_can(struct at91_can_data *data);
-
- /* LEDs */
-extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
-
-#endif

arch/arm/mach-at91/clock.c

@@ -1,977 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/clock.c
- *
- * Copyright (C) 2005 David Brownell
- * Copyright (C) 2005 Ivan Kokshaysky
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/fs.h>
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-#include <linux/list.h>
-#include <linux/errno.h>
-#include <linux/err.h>
-#include <linux/spinlock.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/of_address.h>
-#include <linux/clk/at91_pmc.h>
-
-#include <mach/hardware.h>
-#include <mach/cpu.h>
-
-#include <asm/proc-fns.h>
-
-#include "clock.h"
-#include "generic.h"
-
-void __iomem *at91_pmc_base;
-EXPORT_SYMBOL_GPL(at91_pmc_base);
-
-/*
- * There's a lot more which can be done with clocks, including cpufreq
- * integration, slow clock mode support (for system suspend), letting
- * PLLB be used at other rates (on boards that don't need USB), etc.
- */
-
-#define clk_is_primary(x)	((x)->type & CLK_TYPE_PRIMARY)
-#define clk_is_programmable(x)	((x)->type & CLK_TYPE_PROGRAMMABLE)
-#define clk_is_peripheral(x)	((x)->type & CLK_TYPE_PERIPHERAL)
-#define clk_is_sys(x)		((x)->type & CLK_TYPE_SYSTEM)
-
-
-/*
- * Chips have some kind of clocks : group them by functionality
- */
-#define cpu_has_utmi()		(  cpu_is_at91sam9rl() \
-				|| cpu_is_at91sam9g45() \
-				|| cpu_is_at91sam9x5() \
-				|| cpu_is_sama5d3())
-
-#define cpu_has_1056M_plla()	(cpu_is_sama5d3())
-
-#define cpu_has_800M_plla()	(  cpu_is_at91sam9g20() \
-				|| cpu_is_at91sam9g45() \
-				|| cpu_is_at91sam9x5() \
-				|| cpu_is_at91sam9n12())
-
-#define cpu_has_300M_plla()	(cpu_is_at91sam9g10())
-
-#define cpu_has_240M_plla()	(cpu_is_at91sam9261() \
-				|| cpu_is_at91sam9263() \
-				|| cpu_is_at91sam9rl())
-
-#define cpu_has_210M_plla()	(cpu_is_at91sam9260())
-
-#define cpu_has_pllb()		(!(cpu_is_at91sam9rl() \
-				|| cpu_is_at91sam9g45() \
-				|| cpu_is_at91sam9x5() \
-				|| cpu_is_sama5d3()))
-
-#define cpu_has_upll()		(cpu_is_at91sam9g45() \
-				|| cpu_is_at91sam9x5() \
-				|| cpu_is_sama5d3())
-
-/* USB host HS & FS */
-#define cpu_has_uhp()		(!cpu_is_at91sam9rl())
-
-/* USB device FS only */
-#define cpu_has_udpfs()		(!(cpu_is_at91sam9rl() \
-				|| cpu_is_at91sam9g45() \
-				|| cpu_is_at91sam9x5() \
-				|| cpu_is_sama5d3()))
-
-#define cpu_has_plladiv2()	(cpu_is_at91sam9g45() \
-				|| cpu_is_at91sam9x5() \
-				|| cpu_is_at91sam9n12() \
-				|| cpu_is_sama5d3())
-
-#define cpu_has_mdiv3()		(cpu_is_at91sam9g45() \
-				|| cpu_is_at91sam9x5() \
-				|| cpu_is_at91sam9n12() \
-				|| cpu_is_sama5d3())
-
-#define cpu_has_alt_prescaler()	(cpu_is_at91sam9x5() \
-				|| cpu_is_at91sam9n12() \
-				|| cpu_is_sama5d3())
-
-static LIST_HEAD(clocks);
-static DEFINE_SPINLOCK(clk_lock);
-
-static u32 at91_pllb_usb_init;
-
-/*
- * Four primary clock sources:  two crystal oscillators (32K, main), and
- * two PLLs.  PLLA usually runs the master clock; and PLLB must run at
- * 48 MHz (unless no USB function clocks are needed).  The main clock and
- * both PLLs are turned off to run in "slow clock mode" (system suspend).
- */
-struct clk clk32k = {
-	.name		= "clk32k",
-	.rate_hz	= AT91_SLOW_CLOCK,
-	.users		= 1,		/* always on */
-	.id		= 0,
-	.type		= CLK_TYPE_PRIMARY,
-};
-static struct clk main_clk = {
-	.name		= "main",
-	.pmc_mask	= AT91_PMC_MOSCS,	/* in PMC_SR */
-	.id		= 1,
-	.type		= CLK_TYPE_PRIMARY,
-};
-static struct clk plla = {
-	.name		= "plla",
-	.parent		= &main_clk,
-	.pmc_mask	= AT91_PMC_LOCKA,	/* in PMC_SR */
-	.id		= 2,
-	.type		= CLK_TYPE_PRIMARY | CLK_TYPE_PLL,
-};
-
-static void pllb_mode(struct clk *clk, int is_on)
-{
-	u32	value;
-
-	if (is_on) {
-		is_on = AT91_PMC_LOCKB;
-		value = at91_pllb_usb_init;
-	} else
-		value = 0;
-
-	// REVISIT: Add work-around for AT91RM9200 Errata #26 ?
-	at91_pmc_write(AT91_CKGR_PLLBR, value);
-
-	do {
-		cpu_relax();
-	} while ((at91_pmc_read(AT91_PMC_SR) & AT91_PMC_LOCKB) != is_on);
-}
-
-static struct clk pllb = {
-	.name		= "pllb",
-	.parent		= &main_clk,
-	.pmc_mask	= AT91_PMC_LOCKB,	/* in PMC_SR */
-	.mode		= pllb_mode,
-	.id		= 3,
-	.type		= CLK_TYPE_PRIMARY | CLK_TYPE_PLL,
-};
-
-static void pmc_sys_mode(struct clk *clk, int is_on)
-{
-	if (is_on)
-		at91_pmc_write(AT91_PMC_SCER, clk->pmc_mask);
-	else
-		at91_pmc_write(AT91_PMC_SCDR, clk->pmc_mask);
-}
-
-static void pmc_uckr_mode(struct clk *clk, int is_on)
-{
-	unsigned int uckr = at91_pmc_read(AT91_CKGR_UCKR);
-
-	if (is_on) {
-		is_on = AT91_PMC_LOCKU;
-		at91_pmc_write(AT91_CKGR_UCKR, uckr | clk->pmc_mask);
-	} else
-		at91_pmc_write(AT91_CKGR_UCKR, uckr & ~(clk->pmc_mask));
-
-	do {
-		cpu_relax();
-	} while ((at91_pmc_read(AT91_PMC_SR) & AT91_PMC_LOCKU) != is_on);
-}
-
-/* USB function clocks (PLLB must be 48 MHz) */
-static struct clk udpck = {
-	.name		= "udpck",
-	.parent		= &pllb,
-	.mode		= pmc_sys_mode,
-};
-struct clk utmi_clk = {
-	.name		= "utmi_clk",
-	.parent		= &main_clk,
-	.pmc_mask	= AT91_PMC_UPLLEN,	/* in CKGR_UCKR */
-	.mode		= pmc_uckr_mode,
-	.type		= CLK_TYPE_PLL,
-};
-static struct clk uhpck = {
-	.name		= "uhpck",
-	/*.parent		= ... we choose parent at runtime */
-	.mode		= pmc_sys_mode,
-};
-
-
-/*
- * The master clock is divided from the CPU clock (by 1-4).  It's used for
- * memory, interfaces to on-chip peripherals, the AIC, and sometimes more
- * (e.g baud rate generation).  It's sourced from one of the primary clocks.
- */
-struct clk mck = {
-	.name		= "mck",
-	.pmc_mask	= AT91_PMC_MCKRDY,	/* in PMC_SR */
-};
-
-static void pmc_periph_mode(struct clk *clk, int is_on)
-{
-	u32 regval = 0;
-
-	/*
-	 * With sama5d3 devices, we are managing clock division so we have to
-	 * use the Peripheral Control Register introduced from at91sam9x5
-	 * devices.
-	 */
-	if (cpu_is_sama5d3()) {
-		regval |= AT91_PMC_PCR_CMD; /* write command */
-		regval |= clk->pid & AT91_PMC_PCR_PID; /* peripheral selection */
-		regval |= AT91_PMC_PCR_DIV(clk->div);
-		if (is_on)
-			regval |= AT91_PMC_PCR_EN; /* enable clock */
-		at91_pmc_write(AT91_PMC_PCR, regval);
-	} else {
-		if (is_on)
-			at91_pmc_write(AT91_PMC_PCER, clk->pmc_mask);
-		else
-			at91_pmc_write(AT91_PMC_PCDR, clk->pmc_mask);
-	}
-}
-
-static struct clk __init *at91_css_to_clk(unsigned long css)
-{
-	switch (css) {
-		case AT91_PMC_CSS_SLOW:
-			return &clk32k;
-		case AT91_PMC_CSS_MAIN:
-			return &main_clk;
-		case AT91_PMC_CSS_PLLA:
-			return &plla;
-		case AT91_PMC_CSS_PLLB:
-			if (cpu_has_upll())
-				/* CSS_PLLB == CSS_UPLL */
-				return &utmi_clk;
-			else if (cpu_has_pllb())
-				return &pllb;
-			break;
-		/* alternate PMC: can use master clock */
-		case AT91_PMC_CSS_MASTER:
-			return &mck;
-	}
-
-	return NULL;
-}
-
-static int pmc_prescaler_divider(u32 reg)
-{
-	if (cpu_has_alt_prescaler()) {
-		return 1 << ((reg & AT91_PMC_ALT_PRES) >> PMC_ALT_PRES_OFFSET);
-	} else {
-		return 1 << ((reg & AT91_PMC_PRES) >> PMC_PRES_OFFSET);
-	}
-}
-
-static void __clk_enable(struct clk *clk)
-{
-	if (clk->parent)
-		__clk_enable(clk->parent);
-	if (clk->users++ == 0 && clk->mode)
-		clk->mode(clk, 1);
-}
-
-int clk_enable(struct clk *clk)
-{
-	unsigned long	flags;
-
-	spin_lock_irqsave(&clk_lock, flags);
-	__clk_enable(clk);
-	spin_unlock_irqrestore(&clk_lock, flags);
-	return 0;
-}
-EXPORT_SYMBOL(clk_enable);
-
-static void __clk_disable(struct clk *clk)
-{
-	BUG_ON(clk->users == 0);
-	if (--clk->users == 0 && clk->mode)
-		clk->mode(clk, 0);
-	if (clk->parent)
-		__clk_disable(clk->parent);
-}
-
-void clk_disable(struct clk *clk)
-{
-	unsigned long	flags;
-
-	spin_lock_irqsave(&clk_lock, flags);
-	__clk_disable(clk);
-	spin_unlock_irqrestore(&clk_lock, flags);
-}
-EXPORT_SYMBOL(clk_disable);
-
-unsigned long clk_get_rate(struct clk *clk)
-{
-	unsigned long	flags;
-	unsigned long	rate;
-
-	spin_lock_irqsave(&clk_lock, flags);
-	for (;;) {
-		rate = clk->rate_hz;
-		if (rate || !clk->parent)
-			break;
-		clk = clk->parent;
-	}
-	spin_unlock_irqrestore(&clk_lock, flags);
-	return rate;
-}
-EXPORT_SYMBOL(clk_get_rate);
-
-/*------------------------------------------------------------------------*/
-
-/*
- * For now, only the programmable clocks support reparenting (MCK could
- * do this too, with care) or rate changing (the PLLs could do this too,
- * ditto MCK but that's more for cpufreq).  Drivers may reparent to get
- * a better rate match; we don't.
- */
-
-long clk_round_rate(struct clk *clk, unsigned long rate)
-{
-	unsigned long	flags;
-	unsigned	prescale;
-	unsigned long	actual;
-	unsigned long	prev = ULONG_MAX;
-
-	if (!clk_is_programmable(clk))
-		return -EINVAL;
-	spin_lock_irqsave(&clk_lock, flags);
-
-	actual = clk->parent->rate_hz;
-	for (prescale = 0; prescale < 7; prescale++) {
-		if (actual > rate)
-			prev = actual;
-
-		if (actual && actual <= rate) {
-			if ((prev - rate) < (rate - actual)) {
-				actual = prev;
-				prescale--;
-			}
-			break;
-		}
-		actual >>= 1;
-	}
-
-	spin_unlock_irqrestore(&clk_lock, flags);
-	return (prescale < 7) ? actual : -ENOENT;
-}
-EXPORT_SYMBOL(clk_round_rate);
-
-int clk_set_rate(struct clk *clk, unsigned long rate)
-{
-	unsigned long	flags;
-	unsigned	prescale;
-	unsigned long	prescale_offset, css_mask;
-	unsigned long	actual;
-
-	if (!clk_is_programmable(clk))
-		return -EINVAL;
-	if (clk->users)
-		return -EBUSY;
-
-	if (cpu_has_alt_prescaler()) {
-		prescale_offset = PMC_ALT_PRES_OFFSET;
-		css_mask = AT91_PMC_ALT_PCKR_CSS;
-	} else {
-		prescale_offset = PMC_PRES_OFFSET;
-		css_mask = AT91_PMC_CSS;
-	}
-
-	spin_lock_irqsave(&clk_lock, flags);
-
-	actual = clk->parent->rate_hz;
-	for (prescale = 0; prescale < 7; prescale++) {
-		if (actual && actual <= rate) {
-			u32	pckr;
-
-			pckr = at91_pmc_read(AT91_PMC_PCKR(clk->id));
-			pckr &= css_mask;	/* keep clock selection */
-			pckr |= prescale << prescale_offset;
-			at91_pmc_write(AT91_PMC_PCKR(clk->id), pckr);
-			clk->rate_hz = actual;
-			break;
-		}
-		actual >>= 1;
-	}
-
-	spin_unlock_irqrestore(&clk_lock, flags);
-	return (prescale < 7) ? actual : -ENOENT;
-}
-EXPORT_SYMBOL(clk_set_rate);
-
-struct clk *clk_get_parent(struct clk *clk)
-{
-	return clk->parent;
-}
-EXPORT_SYMBOL(clk_get_parent);
-
-int clk_set_parent(struct clk *clk, struct clk *parent)
-{
-	unsigned long	flags;
-
-	if (clk->users)
-		return -EBUSY;
-	if (!clk_is_primary(parent) || !clk_is_programmable(clk))
-		return -EINVAL;
-
-	if (cpu_is_at91sam9rl() && parent->id == AT91_PMC_CSS_PLLB)
-		return -EINVAL;
-
-	spin_lock_irqsave(&clk_lock, flags);
-
-	clk->rate_hz = parent->rate_hz;
-	clk->parent = parent;
-	at91_pmc_write(AT91_PMC_PCKR(clk->id), parent->id);
-
-	spin_unlock_irqrestore(&clk_lock, flags);
-	return 0;
-}
-EXPORT_SYMBOL(clk_set_parent);
-
-/* establish PCK0..PCKN parentage and rate */
-static void __init init_programmable_clock(struct clk *clk)
-{
-	struct clk	*parent;
-	u32		pckr;
-	unsigned int	css_mask;
-
-	if (cpu_has_alt_prescaler())
-		css_mask = AT91_PMC_ALT_PCKR_CSS;
-	else
-		css_mask = AT91_PMC_CSS;
-
-	pckr = at91_pmc_read(AT91_PMC_PCKR(clk->id));
-	parent = at91_css_to_clk(pckr & css_mask);
-	clk->parent = parent;
-	clk->rate_hz = parent->rate_hz / pmc_prescaler_divider(pckr);
-}
-
-/*------------------------------------------------------------------------*/
-
-#ifdef CONFIG_DEBUG_FS
-
-static int at91_clk_show(struct seq_file *s, void *unused)
-{
-	u32		scsr, pcsr, pcsr1 = 0, uckr = 0, sr;
-	struct clk	*clk;
-
-	scsr = at91_pmc_read(AT91_PMC_SCSR);
-	pcsr = at91_pmc_read(AT91_PMC_PCSR);
-	if (cpu_is_sama5d3())
-		pcsr1 = at91_pmc_read(AT91_PMC_PCSR1);
-	sr = at91_pmc_read(AT91_PMC_SR);
-	seq_printf(s, "SCSR = %8x\n", scsr);
-	seq_printf(s, "PCSR = %8x\n", pcsr);
-	if (cpu_is_sama5d3())
-		seq_printf(s, "PCSR1 = %8x\n", pcsr1);
-	seq_printf(s, "MOR  = %8x\n", at91_pmc_read(AT91_CKGR_MOR));
-	seq_printf(s, "MCFR = %8x\n", at91_pmc_read(AT91_CKGR_MCFR));
-	seq_printf(s, "PLLA = %8x\n", at91_pmc_read(AT91_CKGR_PLLAR));
-	if (cpu_has_pllb())
-		seq_printf(s, "PLLB = %8x\n", at91_pmc_read(AT91_CKGR_PLLBR));
-	if (cpu_has_utmi()) {
-		uckr = at91_pmc_read(AT91_CKGR_UCKR);
-		seq_printf(s, "UCKR = %8x\n", uckr);
-	}
-	seq_printf(s, "MCKR = %8x\n", at91_pmc_read(AT91_PMC_MCKR));
-	if (cpu_has_upll() || cpu_is_at91sam9n12())
-		seq_printf(s, "USB  = %8x\n", at91_pmc_read(AT91_PMC_USB));
-	seq_printf(s, "SR   = %8x\n", sr);
-
-	seq_printf(s, "\n");
-
-	list_for_each_entry(clk, &clocks, node) {
-		char	*state;
-
-		if (clk->mode == pmc_sys_mode) {
-			state = (scsr & clk->pmc_mask) ? "on" : "off";
-		} else if (clk->mode == pmc_periph_mode) {
-			if (cpu_is_sama5d3()) {
-				u32 pmc_mask = 1 << (clk->pid % 32);
-
-				if (clk->pid > 31)
-					state = (pcsr1 & pmc_mask) ? "on" : "off";
-				else
-					state = (pcsr & pmc_mask) ? "on" : "off";
-			} else {
-				state = (pcsr & clk->pmc_mask) ? "on" : "off";
-			}
-		} else if (clk->mode == pmc_uckr_mode) {
-			state = (uckr & clk->pmc_mask) ? "on" : "off";
-		} else if (clk->pmc_mask) {
-			state = (sr & clk->pmc_mask) ? "on" : "off";
-		} else if (clk == &clk32k || clk == &main_clk) {
-			state = "on";
-		} else {
-			state = "";
-		}
-
-		seq_printf(s, "%-10s users=%2d %-3s %9lu Hz %s\n",
-			clk->name, clk->users, state, clk_get_rate(clk),
-			clk->parent ? clk->parent->name : "");
-	}
-	return 0;
-}
-
-static int at91_clk_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, at91_clk_show, NULL);
-}
-
-static const struct file_operations at91_clk_operations = {
-	.open		= at91_clk_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
-
-static int __init at91_clk_debugfs_init(void)
-{
-	/* /sys/kernel/debug/at91_clk */
-	(void) debugfs_create_file("at91_clk", S_IFREG | S_IRUGO, NULL, NULL, &at91_clk_operations);
-
-	return 0;
-}
-postcore_initcall(at91_clk_debugfs_init);
-
-#endif
-
-/*------------------------------------------------------------------------*/
-
-/* Register a new clock */
-static void __init at91_clk_add(struct clk *clk)
-{
-	list_add_tail(&clk->node, &clocks);
-
-	clk->cl.con_id = clk->name;
-	clk->cl.clk = clk;
-	clkdev_add(&clk->cl);
-}
-
-int __init clk_register(struct clk *clk)
-{
-	if (clk_is_peripheral(clk)) {
-		if (!clk->parent)
-			clk->parent = &mck;
-		if (cpu_is_sama5d3())
-			clk->rate_hz = DIV_ROUND_UP(clk->parent->rate_hz,
-						    1 << clk->div);
-		clk->mode = pmc_periph_mode;
-	}
-	else if (clk_is_sys(clk)) {
-		clk->parent = &mck;
-		clk->mode = pmc_sys_mode;
-	}
-	else if (clk_is_programmable(clk)) {
-		clk->mode = pmc_sys_mode;
-		init_programmable_clock(clk);
-	}
-
-	at91_clk_add(clk);
-
-	return 0;
-}
-
-/*------------------------------------------------------------------------*/
-
-static u32 __init at91_pll_rate(struct clk *pll, u32 freq, u32 reg)
-{
-	unsigned mul, div;
-
-	div = reg & 0xff;
-	if (cpu_is_sama5d3())
-		mul = AT91_PMC3_MUL_GET(reg);
-	else
-		mul = AT91_PMC_MUL_GET(reg);
-
-	if (div && mul) {
-		freq /= div;
-		freq *= mul + 1;
-	} else
-		freq = 0;
-
-	return freq;
-}
-
-static u32 __init at91_usb_rate(struct clk *pll, u32 freq, u32 reg)
-{
-	if (pll == &pllb && (reg & AT91_PMC_USB96M))
-		return freq / 2;
-	else if (pll == &utmi_clk || cpu_is_at91sam9n12())
-		return freq / (1 + ((reg & AT91_PMC_OHCIUSBDIV) >> 8));
-	else
-		return freq;
-}
-
-static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq)
-{
-	unsigned i, div = 0, mul = 0, diff = 1 << 30;
-	unsigned ret = (out_freq > 155000000) ? 0xbe00 : 0x3e00;
-
-	/* PLL output max 240 MHz (or 180 MHz per errata) */
-	if (out_freq > 240000000)
-		goto fail;
-
-	for (i = 1; i < 256; i++) {
-		int diff1;
-		unsigned input, mul1;
-
-		/*
-		 * PLL input between 1MHz and 32MHz per spec, but lower
-		 * frequences seem necessary in some cases so allow 100K.
-		 * Warning: some newer products need 2MHz min.
-		 */
-		input = main_freq / i;
-		if (cpu_is_at91sam9g20() && input < 2000000)
-			continue;
-		if (input < 100000)
-			continue;
-		if (input > 32000000)
-			continue;
-
-		mul1 = out_freq / input;
-		if (cpu_is_at91sam9g20() && mul > 63)
-			continue;
-		if (mul1 > 2048)
-			continue;
-		if (mul1 < 2)
-			goto fail;
-
-		diff1 = out_freq - input * mul1;
-		if (diff1 < 0)
-			diff1 = -diff1;
-		if (diff > diff1) {
-			diff = diff1;
-			div = i;
-			mul = mul1;
-			if (diff == 0)
-				break;
-		}
-	}
-	if (i == 256 && diff > (out_freq >> 5))
-		goto fail;
-	return ret | ((mul - 1) << 16) | div;
-fail:
-	return 0;
-}
-
-static struct clk *const standard_pmc_clocks[] __initconst = {
-	/* four primary clocks */
-	&clk32k,
-	&main_clk,
-	&plla,
-
-	/* MCK */
-	&mck
-};
-
-/* PLLB generated USB full speed clock init */
-static void __init at91_pllb_usbfs_clock_init(unsigned long main_clock)
-{
-	unsigned int reg;
-
-	/*
-	 * USB clock init:  choose 48 MHz PLLB value,
-	 * disable 48MHz clock during usb peripheral suspend.
-	 *
-	 * REVISIT:  assumes MCK doesn't derive from PLLB!
-	 */
-	uhpck.parent = &pllb;
-
-	reg = at91_pllb_usb_init = at91_pll_calc(main_clock, 48000000 * 2);
-	pllb.rate_hz = at91_pll_rate(&pllb, main_clock, at91_pllb_usb_init);
-	if (cpu_is_at91rm9200()) {
-		reg = at91_pllb_usb_init |= AT91_PMC_USB96M;
-		uhpck.pmc_mask = AT91RM9200_PMC_UHP;
-		udpck.pmc_mask = AT91RM9200_PMC_UDP;
-		at91_pmc_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
-	} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() ||
-		   cpu_is_at91sam9263() || cpu_is_at91sam9g20() ||
-		   cpu_is_at91sam9g10()) {
-		reg = at91_pllb_usb_init |= AT91_PMC_USB96M;
-		uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
-		udpck.pmc_mask = AT91SAM926x_PMC_UDP;
-	} else if (cpu_is_at91sam9n12()) {
-		/* Divider for USB clock is in USB clock register for 9n12 */
-		reg = AT91_PMC_USBS_PLLB;
-
-		/* For PLLB output 96M, set usb divider 2 (USBDIV + 1) */
-		reg |= AT91_PMC_OHCIUSBDIV_2;
-		at91_pmc_write(AT91_PMC_USB, reg);
-
-		/* Still setup masks */
-		uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
-		udpck.pmc_mask = AT91SAM926x_PMC_UDP;
-	}
-	at91_pmc_write(AT91_CKGR_PLLBR, 0);
-
-	udpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, reg);
-	uhpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, reg);
-}
-
-/* UPLL generated USB full speed clock init */
-static void __init at91_upll_usbfs_clock_init(unsigned long main_clock)
-{
-	/*
-	 * USB clock init: choose 480 MHz from UPLL,
-	 */
-	unsigned int usbr = AT91_PMC_USBS_UPLL;
-
-	/* Setup divider by 10 to reach 48 MHz */
-	usbr |= ((10 - 1) << 8) & AT91_PMC_OHCIUSBDIV;
-
-	at91_pmc_write(AT91_PMC_USB, usbr);
-
-	/* Now set uhpck values */
-	uhpck.parent = &utmi_clk;
-	uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
-	uhpck.rate_hz = at91_usb_rate(&utmi_clk, utmi_clk.rate_hz, usbr);
-}
-
-static int __init at91_pmc_init(unsigned long main_clock)
-{
-	unsigned tmp, freq, mckr;
-	int i;
-	int pll_overclock = false;
-
-	/*
-	 * When the bootloader initialized the main oscillator correctly,
-	 * there's no problem using the cycle counter.  But if it didn't,
-	 * or when using oscillator bypass mode, we must be told the speed
-	 * of the main clock.
-	 */
-	if (!main_clock) {
-		do {
-			tmp = at91_pmc_read(AT91_CKGR_MCFR);
-		} while (!(tmp & AT91_PMC_MAINRDY));
-		main_clock = (tmp & AT91_PMC_MAINF) * (AT91_SLOW_CLOCK / 16);
-	}
-	main_clk.rate_hz = main_clock;
-
-	/* report if PLLA is more than mildly overclocked */
-	plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_pmc_read(AT91_CKGR_PLLAR));
-	if (cpu_has_1056M_plla()) {
-		if (plla.rate_hz > 1056000000)
-			pll_overclock = true;
-	} else if (cpu_has_800M_plla()) {
-		if (plla.rate_hz > 800000000)
-			pll_overclock = true;
-	} else if (cpu_has_300M_plla()) {
-		if (plla.rate_hz > 300000000)
-			pll_overclock = true;
-	} else if (cpu_has_240M_plla()) {
-		if (plla.rate_hz > 240000000)
-			pll_overclock = true;
-	} else if (cpu_has_210M_plla()) {
-		if (plla.rate_hz > 210000000)
-			pll_overclock = true;
-	} else {
-		if (plla.rate_hz > 209000000)
-			pll_overclock = true;
-	}
-	if (pll_overclock)
-		pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
-
-	if (cpu_has_plladiv2()) {
-		mckr = at91_pmc_read(AT91_PMC_MCKR);
-		plla.rate_hz /= (1 << ((mckr & AT91_PMC_PLLADIV2) >> 12));	/* plla divisor by 2 */
-	}
-
-	if (!cpu_has_pllb() && cpu_has_upll()) {
-		/* setup UTMI clock as the fourth primary clock
-		 * (instead of pllb) */
-		utmi_clk.type |= CLK_TYPE_PRIMARY;
-		utmi_clk.id = 3;
-	}
-
-
-	/*
-	 * USB HS clock init
-	 */
-	if (cpu_has_utmi()) {
-		/*
-		 * multiplier is hard-wired to 40
-		 * (obtain the USB High Speed 480 MHz when input is 12 MHz)
-		 */
-		utmi_clk.rate_hz = 40 * utmi_clk.parent->rate_hz;
-
-		/* UTMI bias and PLL are managed at the same time */
-		if (cpu_has_upll())
-			utmi_clk.pmc_mask |= AT91_PMC_BIASEN;
-	}
-
-	/*
-	 * USB FS clock init
-	 */
-	if (cpu_has_pllb())
-		at91_pllb_usbfs_clock_init(main_clock);
-	if (cpu_has_upll())
-		/* assumes that we choose UPLL for USB and not PLLA */
-		at91_upll_usbfs_clock_init(main_clock);
-
-	/*
-	 * MCK and CPU derive from one of those primary clocks.
-	 * For now, assume this parentage won't change.
-	 */
-	mckr = at91_pmc_read(AT91_PMC_MCKR);
-	mck.parent = at91_css_to_clk(mckr & AT91_PMC_CSS);
-	freq = mck.parent->rate_hz;
-	freq /= pmc_prescaler_divider(mckr);					/* prescale */
-	if (cpu_is_at91rm9200()) {
-		mck.rate_hz = freq / (1 + ((mckr & AT91_PMC_MDIV) >> 8));	/* mdiv */
-	} else if (cpu_is_at91sam9g20()) {
-		mck.rate_hz = (mckr & AT91_PMC_MDIV) ?
-			freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq;	/* mdiv ; (x >> 7) = ((x >> 8) * 2) */
-		if (mckr & AT91_PMC_PDIV)
-			freq /= 2;		/* processor clock division */
-	} else if (cpu_has_mdiv3()) {
-		mck.rate_hz = (mckr & AT91_PMC_MDIV) == AT91SAM9_PMC_MDIV_3 ?
-			freq / 3 : freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));	/* mdiv */
-	} else {
-		mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));		/* mdiv */
-	}
-
-	if (cpu_has_alt_prescaler()) {
-		/* Programmable clocks can use MCK */
-		mck.type |= CLK_TYPE_PRIMARY;
-		mck.id = 4;
-	}
-
-	/* Register the PMC's standard clocks */
-	for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++)
-		at91_clk_add(standard_pmc_clocks[i]);
-
-	if (cpu_has_pllb())
-		at91_clk_add(&pllb);
-
-	if (cpu_has_uhp())
-		at91_clk_add(&uhpck);
-
-	if (cpu_has_udpfs())
-		at91_clk_add(&udpck);
-
-	if (cpu_has_utmi())
-		at91_clk_add(&utmi_clk);
-
-	/* MCK and CPU clock are "always on" */
-	clk_enable(&mck);
-
-	printk("Clocks: CPU %u MHz, master %u MHz, main %u.%03u MHz\n",
-		freq / 1000000, (unsigned) mck.rate_hz / 1000000,
-		(unsigned) main_clock / 1000000,
-		((unsigned) main_clock % 1000000) / 1000);
-
-	return 0;
-}
-
-#if defined(CONFIG_OF)
-static struct of_device_id pmc_ids[] = {
-	{ .compatible = "atmel,at91rm9200-pmc" },
-	{ .compatible = "atmel,at91sam9260-pmc" },
-	{ .compatible = "atmel,at91sam9g45-pmc" },
-	{ .compatible = "atmel,at91sam9n12-pmc" },
-	{ .compatible = "atmel,at91sam9x5-pmc" },
-	{ .compatible = "atmel,sama5d3-pmc" },
-	{ /*sentinel*/ }
-};
-
-static struct of_device_id osc_ids[] = {
-	{ .compatible = "atmel,osc" },
-	{ /*sentinel*/ }
-};
-
-int __init at91_dt_clock_init(void)
-{
-	struct device_node *np;
-	u32 main_clock = 0;
-
-	np = of_find_matching_node(NULL, pmc_ids);
-	if (!np)
-		panic("unable to find compatible pmc node in dtb\n");
-
-	at91_pmc_base = of_iomap(np, 0);
-	if (!at91_pmc_base)
-		panic("unable to map pmc cpu registers\n");
-
-	of_node_put(np);
-
-	/* retrieve the freqency of fixed clocks from device tree */
-	np = of_find_matching_node(NULL, osc_ids);
-	if (np) {
-		u32 rate;
-		if (!of_property_read_u32(np, "clock-frequency", &rate))
-			main_clock = rate;
-	}
-
-	of_node_put(np);
-
-	return at91_pmc_init(main_clock);
-}
-#endif
-
-int __init at91_clock_init(unsigned long main_clock)
-{
-	at91_pmc_base = ioremap(AT91_PMC, 256);
-	if (!at91_pmc_base)
-		panic("Impossible to ioremap AT91_PMC 0x%x\n", AT91_PMC);
-
-	return at91_pmc_init(main_clock);
-}
-
-/*
- * Several unused clocks may be active.  Turn them off.
- */
-static int __init at91_clock_reset(void)
-{
-	unsigned long pcdr = 0;
-	unsigned long pcdr1 = 0;
-	unsigned long scdr = 0;
-	struct clk *clk;
-
-	list_for_each_entry(clk, &clocks, node) {
-		if (clk->users > 0)
-			continue;
-
-		if (clk->mode == pmc_periph_mode) {
-			if (cpu_is_sama5d3()) {
-				u32 pmc_mask = 1 << (clk->pid % 32);
-
-				if (clk->pid > 31)
-					pcdr1 |= pmc_mask;
-				else
-					pcdr |= pmc_mask;
-			} else
-				pcdr |= clk->pmc_mask;
-		}
-
-		if (clk->mode == pmc_sys_mode)
-			scdr |= clk->pmc_mask;
-
-		pr_debug("Clocks: disable unused %s\n", clk->name);
-	}
-
-	at91_pmc_write(AT91_PMC_SCDR, scdr);
-	at91_pmc_write(AT91_PMC_PCDR, pcdr);
-	if (cpu_is_sama5d3())
-		at91_pmc_write(AT91_PMC_PCDR1, pcdr1);
-
-	return 0;
-}
-late_initcall(at91_clock_reset);
-
-void at91sam9_idle(void)
-{
-	at91_pmc_write(AT91_PMC_SCDR, AT91_PMC_PCK);
-	cpu_do_idle();
-}

arch/arm/mach-at91/clock.h

@@ -1,50 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/clock.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/clkdev.h>
-
-#define CLK_TYPE_PRIMARY	0x1
-#define CLK_TYPE_PLL		0x2
-#define CLK_TYPE_PROGRAMMABLE	0x4
-#define CLK_TYPE_PERIPHERAL	0x8
-#define CLK_TYPE_SYSTEM		0x10
-
-
-struct clk {
-	struct list_head node;
-	const char	*name;		/* unique clock name */
-	struct clk_lookup cl;
-	unsigned long	rate_hz;
-	unsigned	div;		/* parent clock divider */
-	struct clk	*parent;
-	unsigned	pid;		/* peripheral ID */
-	u32		pmc_mask;
-	void		(*mode)(struct clk *, int);
-	unsigned	id:3;		/* PCK0..4, or 32k/main/a/b */
-	unsigned	type;		/* clock type */
-	u16		users;
-};
-
-
-extern int __init clk_register(struct clk *clk);
-extern struct clk mck;
-extern struct clk utmi_clk;
-extern struct clk clk32k;
-
-#define CLKDEV_CON_ID(_id, _clk)			\
-	{						\
-		.con_id = _id,				\
-		.clk = _clk,				\
-	}
-
-#define CLKDEV_CON_DEV_ID(_con_id, _dev_id, _clk)	\
-	{						\
-		.con_id = _con_id,			\
-		.dev_id = _dev_id,			\
-		.clk = _clk,				\
-	}

arch/arm/mach-at91/generic.h

@@ -11,7 +11,6 @@
 #ifndef _AT91_GENERIC_H
 #define _AT91_GENERIC_H
 
-#include <linux/clkdev.h>
 #include <linux/of.h>
 #include <linux/reboot.h>
 
@@ -23,68 +22,19 @@ extern void __init at91_init_sram(int bank, unsigned long base,
 
  /* Processors */
 extern void __init at91rm9200_set_type(int type);
-extern void __init at91_initialize(unsigned long main_clock);
 extern void __init at91rm9200_dt_initialize(void);
 extern void __init at91_dt_initialize(void);
 
  /* Interrupts */
-extern void __init at91_init_irq_default(void);
-extern void __init at91_init_interrupts(unsigned int priority[]);
-extern void __init at91_aic_init(unsigned int priority[],
-				 unsigned int ext_irq_mask);
-extern int  __init at91_aic_of_init(struct device_node *node,
-				    struct device_node *parent);
-extern int  __init at91_aic5_of_init(struct device_node *node,
-				    struct device_node *parent);
 extern void __init at91_sysirq_mask_rtc(u32 rtc_base);
 extern void __init at91_sysirq_mask_rtt(u32 rtt_base);
 
- /* Devices */
-extern void __init at91_register_devices(void);
-
  /* Timer */
-extern void __init at91_init_time(void);
-extern void at91rm9200_ioremap_st(u32 addr);
 extern void at91rm9200_timer_init(void);
-extern void at91sam926x_ioremap_pit(u32 addr);
-extern void at91sam926x_pit_init(int irq);
-
- /* Clocks */
-#ifdef CONFIG_OLD_CLK_AT91
-extern int __init at91_clock_init(unsigned long main_clock);
-extern int __init at91_dt_clock_init(void);
-#else
-static int inline at91_clock_init(unsigned long main_clock) { return 0; }
-static int inline at91_dt_clock_init(void) { return 0; }
-#endif
-struct device;
-
- /* Power Management */
-extern void at91_irq_suspend(void);
-extern void at91_irq_resume(void);
 
 /* idle */
 extern void at91sam9_idle(void);
 
 /* Matrix */
 extern void at91_ioremap_matrix(u32 base_addr);
-
-/* Ram Controler */
-extern void at91_ioremap_ramc(int id, u32 addr, u32 size);
-
- /* GPIO */
-#define AT91RM9200_PQFP		3	/* AT91RM9200 PQFP package has 3 banks */
-#define AT91RM9200_BGA		4	/* AT91RM9200 BGA package has 4 banks */
-
-struct at91_gpio_bank {
-	unsigned short id;		/* peripheral ID */
-	unsigned long regbase;		/* offset from system peripheral base */
-};
-extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks);
-extern void __init at91_gpio_irq_setup(void);
-extern int  __init at91_gpio_of_irq_setup(struct device_node *node,
-					  struct device_node *parent);
-
-extern u32 at91_get_extern_irq(void);
-
 #endif /* _AT91_GENERIC_H */

arch/arm/mach-at91/gpio.c

@@ -1,982 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/gpio.c
- *
- * Copyright (C) 2005 HP Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#include <linux/clk.h>
-#include <linux/errno.h>
-#include <linux/device.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-#include <linux/kernel.h>
-#include <linux/list.h>
-#include <linux/module.h>
-#include <linux/io.h>
-#include <linux/irqdomain.h>
-#include <linux/irqchip/chained_irq.h>
-#include <linux/of_address.h>
-
-#include <mach/hardware.h>
-#include <mach/at91_pio.h>
-
-#include "generic.h"
-#include "gpio.h"
-
-#define MAX_NB_GPIO_PER_BANK	32
-
-struct at91_gpio_chip {
-	struct gpio_chip	chip;
-	struct at91_gpio_chip	*next;		/* Bank sharing same clock */
-	int			pioc_hwirq;	/* PIO bank interrupt identifier on AIC */
-	int			pioc_virq;	/* PIO bank Linux virtual interrupt */
-	int			pioc_idx;	/* PIO bank index */
-	void __iomem		*regbase;	/* PIO bank virtual address */
-	struct clk		*clock;		/* associated clock */
-	struct irq_domain	*domain;	/* associated irq domain */
-};
-
-#define to_at91_gpio_chip(c) container_of(c, struct at91_gpio_chip, chip)
-
-static int at91_gpiolib_request(struct gpio_chip *chip, unsigned offset);
-static void at91_gpiolib_dbg_show(struct seq_file *s, struct gpio_chip *chip);
-static void at91_gpiolib_set(struct gpio_chip *chip, unsigned offset, int val);
-static int at91_gpiolib_get(struct gpio_chip *chip, unsigned offset);
-static int at91_gpiolib_get_direction(struct gpio_chip *chip, unsigned offset);
-static int at91_gpiolib_direction_output(struct gpio_chip *chip,
-					 unsigned offset, int val);
-static int at91_gpiolib_direction_input(struct gpio_chip *chip,
-					unsigned offset);
-static int at91_gpiolib_to_irq(struct gpio_chip *chip, unsigned offset);
-
-#define AT91_GPIO_CHIP(name)						\
-	{								\
-		.chip = {						\
-			.label		  = name,			\
-			.request	  = at91_gpiolib_request,	\
-			.get_direction    = at91_gpiolib_get_direction, \
-			.direction_input  = at91_gpiolib_direction_input, \
-			.direction_output = at91_gpiolib_direction_output, \
-			.get		  = at91_gpiolib_get,		\
-			.set		  = at91_gpiolib_set,		\
-			.dbg_show	  = at91_gpiolib_dbg_show,	\
-			.to_irq		  = at91_gpiolib_to_irq,	\
-			.ngpio		  = MAX_NB_GPIO_PER_BANK,	\
-		},							\
-	}
-
-static struct at91_gpio_chip gpio_chip[] = {
-	AT91_GPIO_CHIP("pioA"),
-	AT91_GPIO_CHIP("pioB"),
-	AT91_GPIO_CHIP("pioC"),
-	AT91_GPIO_CHIP("pioD"),
-	AT91_GPIO_CHIP("pioE"),
-};
-
-static int gpio_banks;
-static unsigned long at91_gpio_caps;
-
-/* All PIO controllers support PIO3 features */
-#define AT91_GPIO_CAP_PIO3	(1 <<  0)
-
-#define has_pio3()	(at91_gpio_caps & AT91_GPIO_CAP_PIO3)
-
-/*--------------------------------------------------------------------------*/
-
-static inline void __iomem *pin_to_controller(unsigned pin)
-{
-	pin /= MAX_NB_GPIO_PER_BANK;
-	if (likely(pin < gpio_banks))
-		return gpio_chip[pin].regbase;
-
-	return NULL;
-}
-
-static inline unsigned pin_to_mask(unsigned pin)
-{
-	return 1 << (pin % MAX_NB_GPIO_PER_BANK);
-}
-
-
-static char peripheral_function(void __iomem *pio, unsigned mask)
-{
-	char	ret = 'X';
-	u8	select;
-
-	if (pio) {
-		if (has_pio3()) {
-			select = !!(__raw_readl(pio + PIO_ABCDSR1) & mask);
-			select |= (!!(__raw_readl(pio + PIO_ABCDSR2) & mask) << 1);
-			ret = 'A' + select;
-		} else {
-			ret = __raw_readl(pio + PIO_ABSR) & mask ?
-							'B' : 'A';
-		}
-	}
-
-	return ret;
-}
-
-/*--------------------------------------------------------------------------*/
-
-/* Not all hardware capabilities are exposed through these calls; they
- * only encapsulate the most common features and modes.  (So if you
- * want to change signals in groups, do it directly.)
- *
- * Bootloaders will usually handle some of the pin multiplexing setup.
- * The intent is certainly that by the time Linux is fully booted, all
- * pins should have been fully initialized.  These setup calls should
- * only be used by board setup routines, or possibly in driver probe().
- *
- * For bootloaders doing all that setup, these calls could be inlined
- * as NOPs so Linux won't duplicate any setup code
- */
-
-
-/*
- * mux the pin to the "GPIO" peripheral role.
- */
-int __init_or_module at91_set_GPIO_periph(unsigned pin, int use_pullup)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
-	__raw_writel(mask, pio + PIO_PER);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_GPIO_periph);
-
-
-/*
- * mux the pin to the "A" internal peripheral role.
- */
-int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
-	if (has_pio3()) {
-		__raw_writel(__raw_readl(pio + PIO_ABCDSR1) & ~mask,
-							pio + PIO_ABCDSR1);
-		__raw_writel(__raw_readl(pio + PIO_ABCDSR2) & ~mask,
-							pio + PIO_ABCDSR2);
-	} else {
-		__raw_writel(mask, pio + PIO_ASR);
-	}
-	__raw_writel(mask, pio + PIO_PDR);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_A_periph);
-
-
-/*
- * mux the pin to the "B" internal peripheral role.
- */
-int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
-	if (has_pio3()) {
-		__raw_writel(__raw_readl(pio + PIO_ABCDSR1) | mask,
-							pio + PIO_ABCDSR1);
-		__raw_writel(__raw_readl(pio + PIO_ABCDSR2) & ~mask,
-							pio + PIO_ABCDSR2);
-	} else {
-		__raw_writel(mask, pio + PIO_BSR);
-	}
-	__raw_writel(mask, pio + PIO_PDR);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_B_periph);
-
-
-/*
- * mux the pin to the "C" internal peripheral role.
- */
-int __init_or_module at91_set_C_periph(unsigned pin, int use_pullup)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio || !has_pio3())
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
-	__raw_writel(__raw_readl(pio + PIO_ABCDSR1) & ~mask, pio + PIO_ABCDSR1);
-	__raw_writel(__raw_readl(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2);
-	__raw_writel(mask, pio + PIO_PDR);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_C_periph);
-
-
-/*
- * mux the pin to the "D" internal peripheral role.
- */
-int __init_or_module at91_set_D_periph(unsigned pin, int use_pullup)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio || !has_pio3())
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
-	__raw_writel(__raw_readl(pio + PIO_ABCDSR1) | mask, pio + PIO_ABCDSR1);
-	__raw_writel(__raw_readl(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2);
-	__raw_writel(mask, pio + PIO_PDR);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_D_periph);
-
-
-/*
- * mux the pin to the gpio controller (instead of "A", "B", "C"
- * or "D" peripheral), and configure it for an input.
- */
-int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
-	__raw_writel(mask, pio + PIO_ODR);
-	__raw_writel(mask, pio + PIO_PER);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_gpio_input);
-
-
-/*
- * mux the pin to the gpio controller (instead of "A", "B", "C"
- * or "D" peripheral), and configure it for an output.
- */
-int __init_or_module at91_set_gpio_output(unsigned pin, int value)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + PIO_PUDR);
-	__raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR));
-	__raw_writel(mask, pio + PIO_OER);
-	__raw_writel(mask, pio + PIO_PER);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_gpio_output);
-
-
-/*
- * enable/disable the glitch filter; mostly used with IRQ handling.
- */
-int __init_or_module at91_set_deglitch(unsigned pin, int is_on)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	if (has_pio3() && is_on)
-		__raw_writel(mask, pio + PIO_IFSCDR);
-	__raw_writel(mask, pio + (is_on ? PIO_IFER : PIO_IFDR));
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_deglitch);
-
-/*
- * enable/disable the debounce filter;
- */
-int __init_or_module at91_set_debounce(unsigned pin, int is_on, int div)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio || !has_pio3())
-		return -EINVAL;
-
-	if (is_on) {
-		__raw_writel(mask, pio + PIO_IFSCER);
-		__raw_writel(div & PIO_SCDR_DIV, pio + PIO_SCDR);
-		__raw_writel(mask, pio + PIO_IFER);
-	} else {
-		__raw_writel(mask, pio + PIO_IFDR);
-	}
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_debounce);
-
-/*
- * enable/disable the multi-driver; This is only valid for output and
- * allows the output pin to run as an open collector output.
- */
-int __init_or_module at91_set_multi_drive(unsigned pin, int is_on)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + (is_on ? PIO_MDER : PIO_MDDR));
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_multi_drive);
-
-/*
- * enable/disable the pull-down.
- * If pull-up already enabled while calling the function, we disable it.
- */
-int __init_or_module at91_set_pulldown(unsigned pin, int is_on)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio || !has_pio3())
-		return -EINVAL;
-
-	/* Disable pull-up anyway */
-	__raw_writel(mask, pio + PIO_PUDR);
-	__raw_writel(mask, pio + (is_on ? PIO_PPDER : PIO_PPDDR));
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_pulldown);
-
-/*
- * disable Schmitt trigger
- */
-int __init_or_module at91_disable_schmitt_trig(unsigned pin)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio || !has_pio3())
-		return -EINVAL;
-
-	__raw_writel(__raw_readl(pio + PIO_SCHMITT) | mask, pio + PIO_SCHMITT);
-	return 0;
-}
-EXPORT_SYMBOL(at91_disable_schmitt_trig);
-
-/*
- * assuming the pin is muxed as a gpio output, set its value.
- */
-int at91_set_gpio_value(unsigned pin, int value)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-	__raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR));
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_gpio_value);
-
-
-/*
- * read the pin's value (works even if it's not muxed as a gpio).
- */
-int at91_get_gpio_value(unsigned pin)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-	u32		pdsr;
-
-	if (!pio)
-		return -EINVAL;
-	pdsr = __raw_readl(pio + PIO_PDSR);
-	return (pdsr & mask) != 0;
-}
-EXPORT_SYMBOL(at91_get_gpio_value);
-
-/*--------------------------------------------------------------------------*/
-
-#ifdef CONFIG_PM
-
-static u32 wakeups[MAX_GPIO_BANKS];
-static u32 backups[MAX_GPIO_BANKS];
-
-static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
-{
-	struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
-	unsigned	mask = 1 << d->hwirq;
-	unsigned	bank = at91_gpio->pioc_idx;
-
-	if (unlikely(bank >= MAX_GPIO_BANKS))
-		return -EINVAL;
-
-	if (state)
-		wakeups[bank] |= mask;
-	else
-		wakeups[bank] &= ~mask;
-
-	irq_set_irq_wake(at91_gpio->pioc_virq, state);
-
-	return 0;
-}
-
-void at91_gpio_suspend(void)
-{
-	int i;
-
-	for (i = 0; i < gpio_banks; i++) {
-		void __iomem	*pio = gpio_chip[i].regbase;
-
-		backups[i] = __raw_readl(pio + PIO_IMR);
-		__raw_writel(backups[i], pio + PIO_IDR);
-		__raw_writel(wakeups[i], pio + PIO_IER);
-
-		if (!wakeups[i]) {
-			clk_unprepare(gpio_chip[i].clock);
-			clk_disable(gpio_chip[i].clock);
-		} else {
-#ifdef CONFIG_PM_DEBUG
-			printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]);
-#endif
-		}
-	}
-}
-
-void at91_gpio_resume(void)
-{
-	int i;
-
-	for (i = 0; i < gpio_banks; i++) {
-		void __iomem	*pio = gpio_chip[i].regbase;
-
-		if (!wakeups[i]) {
-			if (clk_prepare(gpio_chip[i].clock) == 0)
-				clk_enable(gpio_chip[i].clock);
-		}
-
-		__raw_writel(wakeups[i], pio + PIO_IDR);
-		__raw_writel(backups[i], pio + PIO_IER);
-	}
-}
-
-#else
-#define gpio_irq_set_wake	NULL
-#endif
-
-
-/* Several AIC controller irqs are dispatched through this GPIO handler.
- * To use any AT91_PIN_* as an externally triggered IRQ, first call
- * at91_set_gpio_input() then maybe enable its glitch filter.
- * Then just request_irq() with the pin ID; it works like any ARM IRQ
- * handler.
- * First implementation always triggers on rising and falling edges
- * whereas the newer PIO3 can be additionally configured to trigger on
- * level, edge with any polarity.
- *
- * Alternatively, certain pins may be used directly as IRQ0..IRQ6 after
- * configuring them with at91_set_a_periph() or at91_set_b_periph().
- * IRQ0..IRQ6 should be configurable, e.g. level vs edge triggering.
- */
-
-static void gpio_irq_mask(struct irq_data *d)
-{
-	struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
-	void __iomem	*pio = at91_gpio->regbase;
-	unsigned	mask = 1 << d->hwirq;
-
-	if (pio)
-		__raw_writel(mask, pio + PIO_IDR);
-}
-
-static void gpio_irq_unmask(struct irq_data *d)
-{
-	struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
-	void __iomem	*pio = at91_gpio->regbase;
-	unsigned	mask = 1 << d->hwirq;
-
-	if (pio)
-		__raw_writel(mask, pio + PIO_IER);
-}
-
-static int gpio_irq_type(struct irq_data *d, unsigned type)
-{
-	switch (type) {
-	case IRQ_TYPE_NONE:
-	case IRQ_TYPE_EDGE_BOTH:
-		return 0;
-	default:
-		return -EINVAL;
-	}
-}
-
-/* Alternate irq type for PIO3 support */
-static int alt_gpio_irq_type(struct irq_data *d, unsigned type)
-{
-	struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
-	void __iomem	*pio = at91_gpio->regbase;
-	unsigned	mask = 1 << d->hwirq;
-
-	switch (type) {
-	case IRQ_TYPE_EDGE_RISING:
-		__raw_writel(mask, pio + PIO_ESR);
-		__raw_writel(mask, pio + PIO_REHLSR);
-		break;
-	case IRQ_TYPE_EDGE_FALLING:
-		__raw_writel(mask, pio + PIO_ESR);
-		__raw_writel(mask, pio + PIO_FELLSR);
-		break;
-	case IRQ_TYPE_LEVEL_LOW:
-		__raw_writel(mask, pio + PIO_LSR);
-		__raw_writel(mask, pio + PIO_FELLSR);
-		break;
-	case IRQ_TYPE_LEVEL_HIGH:
-		__raw_writel(mask, pio + PIO_LSR);
-		__raw_writel(mask, pio + PIO_REHLSR);
-		break;
-	case IRQ_TYPE_EDGE_BOTH:
-		/*
-		 * disable additional interrupt modes:
-		 * fall back to default behavior
-		 */
-		__raw_writel(mask, pio + PIO_AIMDR);
-		return 0;
-	case IRQ_TYPE_NONE:
-	default:
-		pr_warn("AT91: No type for irq %d\n", gpio_to_irq(d->irq));
-		return -EINVAL;
-	}
-
-	/* enable additional interrupt modes */
-	__raw_writel(mask, pio + PIO_AIMER);
-
-	return 0;
-}
-
-static struct irq_chip gpio_irqchip = {
-	.name		= "GPIO",
-	.irq_disable	= gpio_irq_mask,
-	.irq_mask	= gpio_irq_mask,
-	.irq_unmask	= gpio_irq_unmask,
-	/* .irq_set_type is set dynamically */
-	.irq_set_wake	= gpio_irq_set_wake,
-};
-
-static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
-{
-	struct irq_chip *chip = irq_desc_get_chip(desc);
-	struct irq_data *idata = irq_desc_get_irq_data(desc);
-	struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata);
-	void __iomem	*pio = at91_gpio->regbase;
-	unsigned long	isr;
-	int		n;
-
-	chained_irq_enter(chip, desc);
-	for (;;) {
-		/* Reading ISR acks pending (edge triggered) GPIO interrupts.
-		 * When there none are pending, we're finished unless we need
-		 * to process multiple banks (like ID_PIOCDE on sam9263).
-		 */
-		isr = __raw_readl(pio + PIO_ISR) & __raw_readl(pio + PIO_IMR);
-		if (!isr) {
-			if (!at91_gpio->next)
-				break;
-			at91_gpio = at91_gpio->next;
-			pio = at91_gpio->regbase;
-			continue;
-		}
-
-		n = find_first_bit(&isr, BITS_PER_LONG);
-		while (n < BITS_PER_LONG) {
-			generic_handle_irq(irq_find_mapping(at91_gpio->domain, n));
-			n = find_next_bit(&isr, BITS_PER_LONG, n + 1);
-		}
-	}
-	chained_irq_exit(chip, desc);
-	/* now it may re-trigger */
-}
-
-/*--------------------------------------------------------------------------*/
-
-#ifdef CONFIG_DEBUG_FS
-
-static void gpio_printf(struct seq_file *s, void __iomem *pio, unsigned mask)
-{
-	char	*trigger = NULL;
-	char	*polarity = NULL;
-
-	if (__raw_readl(pio + PIO_IMR) & mask) {
-		if (!has_pio3() || !(__raw_readl(pio + PIO_AIMMR) & mask )) {
-			trigger = "edge";
-			polarity = "both";
-		} else {
-			if (__raw_readl(pio + PIO_ELSR) & mask) {
-				trigger = "level";
-				polarity = __raw_readl(pio + PIO_FRLHSR) & mask ?
-					"high" : "low";
-			} else {
-				trigger = "edge";
-				polarity = __raw_readl(pio + PIO_FRLHSR) & mask ?
-						"rising" : "falling";
-			}
-		}
-		seq_printf(s, "IRQ:%s-%s\t", trigger, polarity);
-	} else {
-		seq_printf(s, "GPIO:%s\t\t",
-				__raw_readl(pio + PIO_PDSR) & mask ? "1" : "0");
-	}
-}
-
-static int at91_gpio_show(struct seq_file *s, void *unused)
-{
-	int bank, j;
-
-	/* print heading */
-	seq_printf(s, "Pin\t");
-	for (bank = 0; bank < gpio_banks; bank++) {
-		seq_printf(s, "PIO%c\t\t", 'A' + bank);
-	};
-	seq_printf(s, "\n\n");
-
-	/* print pin status */
-	for (j = 0; j < 32; j++) {
-		seq_printf(s, "%i:\t", j);
-
-		for (bank = 0; bank < gpio_banks; bank++) {
-			unsigned	pin  = (32 * bank) + j;
-			void __iomem	*pio = pin_to_controller(pin);
-			unsigned	mask = pin_to_mask(pin);
-
-			if (__raw_readl(pio + PIO_PSR) & mask)
-				gpio_printf(s, pio, mask);
-			else
-				seq_printf(s, "%c\t\t",
-						peripheral_function(pio, mask));
-		}
-
-		seq_printf(s, "\n");
-	}
-
-	return 0;
-}
-
-static int at91_gpio_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, at91_gpio_show, NULL);
-}
-
-static const struct file_operations at91_gpio_operations = {
-	.open		= at91_gpio_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
-
-static int __init at91_gpio_debugfs_init(void)
-{
-	/* /sys/kernel/debug/at91_gpio */
-	(void) debugfs_create_file("at91_gpio", S_IFREG | S_IRUGO, NULL, NULL, &at91_gpio_operations);
-	return 0;
-}
-postcore_initcall(at91_gpio_debugfs_init);
-
-#endif
-
-/*--------------------------------------------------------------------------*/
-
-/*
- * This lock class tells lockdep that GPIO irqs are in a different
- * category than their parents, so it won't report false recursion.
- */
-static struct lock_class_key gpio_lock_class;
-
-/*
- * irqdomain initialization: pile up irqdomains on top of AIC range
- */
-static void __init at91_gpio_irqdomain(struct at91_gpio_chip *at91_gpio)
-{
-	int irq_base;
-
-	irq_base = irq_alloc_descs(-1, 0, at91_gpio->chip.ngpio, 0);
-	if (irq_base < 0)
-		panic("at91_gpio.%d: error %d: couldn't allocate IRQ numbers.\n",
-			at91_gpio->pioc_idx, irq_base);
-	at91_gpio->domain = irq_domain_add_legacy(NULL, at91_gpio->chip.ngpio,
-						  irq_base, 0,
-						  &irq_domain_simple_ops, NULL);
-	if (!at91_gpio->domain)
-		panic("at91_gpio.%d: couldn't allocate irq domain.\n",
-			at91_gpio->pioc_idx);
-}
-
-/*
- * Called from the processor-specific init to enable GPIO interrupt support.
- */
-void __init at91_gpio_irq_setup(void)
-{
-	unsigned		pioc;
-	int			gpio_irqnbr = 0;
-	struct at91_gpio_chip	*this, *prev;
-
-	/* Setup proper .irq_set_type function */
-	if (has_pio3())
-		gpio_irqchip.irq_set_type = alt_gpio_irq_type;
-	else
-		gpio_irqchip.irq_set_type = gpio_irq_type;
-
-	for (pioc = 0, this = gpio_chip, prev = NULL;
-			pioc++ < gpio_banks;
-			prev = this, this++) {
-		int offset;
-
-		__raw_writel(~0, this->regbase + PIO_IDR);
-
-		/* setup irq domain for this GPIO controller */
-		at91_gpio_irqdomain(this);
-
-		for (offset = 0; offset < this->chip.ngpio; offset++) {
-			unsigned int virq = irq_find_mapping(this->domain, offset);
-			irq_set_lockdep_class(virq, &gpio_lock_class);
-
-			/*
-			 * Can use the "simple" and not "edge" handler since it's
-			 * shorter, and the AIC handles interrupts sanely.
-			 */
-			irq_set_chip_and_handler(virq, &gpio_irqchip,
-						 handle_simple_irq);
-			set_irq_flags(virq, IRQF_VALID);
-			irq_set_chip_data(virq, this);
-
-			gpio_irqnbr++;
-		}
-
-		/* The toplevel handler handles one bank of GPIOs, except
-		 * on some SoC it can handles up to three...
-		 * We only set up the handler for the first of the list.
-		 */
-		if (prev && prev->next == this)
-			continue;
-
-		this->pioc_virq = irq_create_mapping(NULL, this->pioc_hwirq);
-		irq_set_chip_data(this->pioc_virq, this);
-		irq_set_chained_handler(this->pioc_virq, gpio_irq_handler);
-	}
-	pr_info("AT91: %d gpio irqs in %d banks\n", gpio_irqnbr, gpio_banks);
-}
-
-/* gpiolib support */
-static int at91_gpiolib_request(struct gpio_chip *chip, unsigned offset)
-{
-	struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
-	void __iomem *pio = at91_gpio->regbase;
-	unsigned mask = 1 << offset;
-
-	__raw_writel(mask, pio + PIO_PER);
-	return 0;
-}
-
-static int at91_gpiolib_get_direction(struct gpio_chip *chip, unsigned offset)
-{
-	struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
-	void __iomem *pio = at91_gpio->regbase;
-	unsigned mask = 1 << offset;
-	u32 osr;
-
-	osr = __raw_readl(pio + PIO_OSR);
-	return !(osr & mask);
-}
-
-static int at91_gpiolib_direction_input(struct gpio_chip *chip,
-					unsigned offset)
-{
-	struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
-	void __iomem *pio = at91_gpio->regbase;
-	unsigned mask = 1 << offset;
-
-	__raw_writel(mask, pio + PIO_ODR);
-	return 0;
-}
-
-static int at91_gpiolib_direction_output(struct gpio_chip *chip,
-					 unsigned offset, int val)
-{
-	struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
-	void __iomem *pio = at91_gpio->regbase;
-	unsigned mask = 1 << offset;
-
-	__raw_writel(mask, pio + (val ? PIO_SODR : PIO_CODR));
-	__raw_writel(mask, pio + PIO_OER);
-	return 0;
-}
-
-static int at91_gpiolib_get(struct gpio_chip *chip, unsigned offset)
-{
-	struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
-	void __iomem *pio = at91_gpio->regbase;
-	unsigned mask = 1 << offset;
-	u32 pdsr;
-
-	pdsr = __raw_readl(pio + PIO_PDSR);
-	return (pdsr & mask) != 0;
-}
-
-static void at91_gpiolib_set(struct gpio_chip *chip, unsigned offset, int val)
-{
-	struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
-	void __iomem *pio = at91_gpio->regbase;
-	unsigned mask = 1 << offset;
-
-	__raw_writel(mask, pio + (val ? PIO_SODR : PIO_CODR));
-}
-
-static void at91_gpiolib_dbg_show(struct seq_file *s, struct gpio_chip *chip)
-{
-	int i;
-
-	for (i = 0; i < chip->ngpio; i++) {
-		unsigned pin = chip->base + i;
-		void __iomem *pio = pin_to_controller(pin);
-		unsigned mask = pin_to_mask(pin);
-		const char *gpio_label;
-
-		gpio_label = gpiochip_is_requested(chip, i);
-		if (gpio_label) {
-			seq_printf(s, "[%s] GPIO%s%d: ",
-				   gpio_label, chip->label, i);
-			if (__raw_readl(pio + PIO_PSR) & mask)
-				seq_printf(s, "[gpio] %s\n",
-					   at91_get_gpio_value(pin) ?
-					   "set" : "clear");
-			else
-				seq_printf(s, "[periph %c]\n",
-					   peripheral_function(pio, mask));
-		}
-	}
-}
-
-static int at91_gpiolib_to_irq(struct gpio_chip *chip, unsigned offset)
-{
-	struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
-	int virq;
-
-	if (offset < chip->ngpio)
-		virq = irq_create_mapping(at91_gpio->domain, offset);
-	else
-		virq = -ENXIO;
-
-	dev_dbg(chip->dev, "%s: request IRQ for GPIO %d, return %d\n",
-				chip->label, offset + chip->base, virq);
-	return virq;
-}
-
-static int __init at91_gpio_setup_clk(int idx)
-{
-	struct at91_gpio_chip *at91_gpio = &gpio_chip[idx];
-
-	/* retreive PIO controller's clock */
-	at91_gpio->clock = clk_get_sys(NULL, at91_gpio->chip.label);
-	if (IS_ERR(at91_gpio->clock)) {
-		pr_err("at91_gpio.%d, failed to get clock, ignoring.\n", idx);
-		goto err;
-	}
-
-	if (clk_prepare(at91_gpio->clock))
-		goto clk_prep_err;
-
-	/* enable PIO controller's clock */
-	if (clk_enable(at91_gpio->clock)) {
-		pr_err("at91_gpio.%d, failed to enable clock, ignoring.\n", idx);
-		goto clk_err;
-	}
-
-	return 0;
-
-clk_err:
-	clk_unprepare(at91_gpio->clock);
-clk_prep_err:
-	clk_put(at91_gpio->clock);
-err:
-	return -EINVAL;
-}
-
-static void __init at91_gpio_init_one(int idx, u32 regbase, int pioc_hwirq)
-{
-	struct at91_gpio_chip *at91_gpio = &gpio_chip[idx];
-
-	at91_gpio->chip.base = idx * MAX_NB_GPIO_PER_BANK;
-	at91_gpio->pioc_hwirq = pioc_hwirq;
-	at91_gpio->pioc_idx = idx;
-
-	at91_gpio->regbase = ioremap(regbase, 512);
-	if (!at91_gpio->regbase) {
-		pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", idx);
-		return;
-	}
-
-	if (at91_gpio_setup_clk(idx))
-		goto ioremap_err;
-
-	gpio_banks = max(gpio_banks, idx + 1);
-	return;
-
-ioremap_err:
-	iounmap(at91_gpio->regbase);
-}
-
-/*
- * Called from the processor-specific init to enable GPIO pin support.
- */
-void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
-{
-	unsigned i;
-	struct at91_gpio_chip *at91_gpio, *last = NULL;
-
-	BUG_ON(nr_banks > MAX_GPIO_BANKS);
-
-	if (of_have_populated_dt())
-		return;
-
-	for (i = 0; i < nr_banks; i++)
-		at91_gpio_init_one(i, data[i].regbase, data[i].id);
-
-	for (i = 0; i < gpio_banks; i++) {
-		at91_gpio = &gpio_chip[i];
-
-		/*
-		 * GPIO controller are grouped on some SoC:
-		 * PIOC, PIOD and PIOE can share the same IRQ line
-		 */
-		if (last && last->pioc_hwirq == at91_gpio->pioc_hwirq)
-			last->next = at91_gpio;
-		last = at91_gpio;
-
-		gpiochip_add(&at91_gpio->chip);
-	}
-}

arch/arm/mach-at91/gpio.h

@@ -1,214 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/gpio.h
- *
- *  Copyright (C) 2005 HP Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#ifndef __ASM_ARCH_AT91RM9200_GPIO_H
-#define __ASM_ARCH_AT91RM9200_GPIO_H
-
-#include <linux/kernel.h>
-#include <asm/irq.h>
-
-#define MAX_GPIO_BANKS		5
-#define NR_BUILTIN_GPIO		(MAX_GPIO_BANKS * 32)
-
-/* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */
-
-#define	AT91_PIN_PA0	(0x00 + 0)
-#define	AT91_PIN_PA1	(0x00 + 1)
-#define	AT91_PIN_PA2	(0x00 + 2)
-#define	AT91_PIN_PA3	(0x00 + 3)
-#define	AT91_PIN_PA4	(0x00 + 4)
-#define	AT91_PIN_PA5	(0x00 + 5)
-#define	AT91_PIN_PA6	(0x00 + 6)
-#define	AT91_PIN_PA7	(0x00 + 7)
-#define	AT91_PIN_PA8	(0x00 + 8)
-#define	AT91_PIN_PA9	(0x00 + 9)
-#define	AT91_PIN_PA10	(0x00 + 10)
-#define	AT91_PIN_PA11	(0x00 + 11)
-#define	AT91_PIN_PA12	(0x00 + 12)
-#define	AT91_PIN_PA13	(0x00 + 13)
-#define	AT91_PIN_PA14	(0x00 + 14)
-#define	AT91_PIN_PA15	(0x00 + 15)
-#define	AT91_PIN_PA16	(0x00 + 16)
-#define	AT91_PIN_PA17	(0x00 + 17)
-#define	AT91_PIN_PA18	(0x00 + 18)
-#define	AT91_PIN_PA19	(0x00 + 19)
-#define	AT91_PIN_PA20	(0x00 + 20)
-#define	AT91_PIN_PA21	(0x00 + 21)
-#define	AT91_PIN_PA22	(0x00 + 22)
-#define	AT91_PIN_PA23	(0x00 + 23)
-#define	AT91_PIN_PA24	(0x00 + 24)
-#define	AT91_PIN_PA25	(0x00 + 25)
-#define	AT91_PIN_PA26	(0x00 + 26)
-#define	AT91_PIN_PA27	(0x00 + 27)
-#define	AT91_PIN_PA28	(0x00 + 28)
-#define	AT91_PIN_PA29	(0x00 + 29)
-#define	AT91_PIN_PA30	(0x00 + 30)
-#define	AT91_PIN_PA31	(0x00 + 31)
-
-#define	AT91_PIN_PB0	(0x20 + 0)
-#define	AT91_PIN_PB1	(0x20 + 1)
-#define	AT91_PIN_PB2	(0x20 + 2)
-#define	AT91_PIN_PB3	(0x20 + 3)
-#define	AT91_PIN_PB4	(0x20 + 4)
-#define	AT91_PIN_PB5	(0x20 + 5)
-#define	AT91_PIN_PB6	(0x20 + 6)
-#define	AT91_PIN_PB7	(0x20 + 7)
-#define	AT91_PIN_PB8	(0x20 + 8)
-#define	AT91_PIN_PB9	(0x20 + 9)
-#define	AT91_PIN_PB10	(0x20 + 10)
-#define	AT91_PIN_PB11	(0x20 + 11)
-#define	AT91_PIN_PB12	(0x20 + 12)
-#define	AT91_PIN_PB13	(0x20 + 13)
-#define	AT91_PIN_PB14	(0x20 + 14)
-#define	AT91_PIN_PB15	(0x20 + 15)
-#define	AT91_PIN_PB16	(0x20 + 16)
-#define	AT91_PIN_PB17	(0x20 + 17)
-#define	AT91_PIN_PB18	(0x20 + 18)
-#define	AT91_PIN_PB19	(0x20 + 19)
-#define	AT91_PIN_PB20	(0x20 + 20)
-#define	AT91_PIN_PB21	(0x20 + 21)
-#define	AT91_PIN_PB22	(0x20 + 22)
-#define	AT91_PIN_PB23	(0x20 + 23)
-#define	AT91_PIN_PB24	(0x20 + 24)
-#define	AT91_PIN_PB25	(0x20 + 25)
-#define	AT91_PIN_PB26	(0x20 + 26)
-#define	AT91_PIN_PB27	(0x20 + 27)
-#define	AT91_PIN_PB28	(0x20 + 28)
-#define	AT91_PIN_PB29	(0x20 + 29)
-#define	AT91_PIN_PB30	(0x20 + 30)
-#define	AT91_PIN_PB31	(0x20 + 31)
-
-#define	AT91_PIN_PC0	(0x40 + 0)
-#define	AT91_PIN_PC1	(0x40 + 1)
-#define	AT91_PIN_PC2	(0x40 + 2)
-#define	AT91_PIN_PC3	(0x40 + 3)
-#define	AT91_PIN_PC4	(0x40 + 4)
-#define	AT91_PIN_PC5	(0x40 + 5)
-#define	AT91_PIN_PC6	(0x40 + 6)
-#define	AT91_PIN_PC7	(0x40 + 7)
-#define	AT91_PIN_PC8	(0x40 + 8)
-#define	AT91_PIN_PC9	(0x40 + 9)
-#define	AT91_PIN_PC10	(0x40 + 10)
-#define	AT91_PIN_PC11	(0x40 + 11)
-#define	AT91_PIN_PC12	(0x40 + 12)
-#define	AT91_PIN_PC13	(0x40 + 13)
-#define	AT91_PIN_PC14	(0x40 + 14)
-#define	AT91_PIN_PC15	(0x40 + 15)
-#define	AT91_PIN_PC16	(0x40 + 16)
-#define	AT91_PIN_PC17	(0x40 + 17)
-#define	AT91_PIN_PC18	(0x40 + 18)
-#define	AT91_PIN_PC19	(0x40 + 19)
-#define	AT91_PIN_PC20	(0x40 + 20)
-#define	AT91_PIN_PC21	(0x40 + 21)
-#define	AT91_PIN_PC22	(0x40 + 22)
-#define	AT91_PIN_PC23	(0x40 + 23)
-#define	AT91_PIN_PC24	(0x40 + 24)
-#define	AT91_PIN_PC25	(0x40 + 25)
-#define	AT91_PIN_PC26	(0x40 + 26)
-#define	AT91_PIN_PC27	(0x40 + 27)
-#define	AT91_PIN_PC28	(0x40 + 28)
-#define	AT91_PIN_PC29	(0x40 + 29)
-#define	AT91_PIN_PC30	(0x40 + 30)
-#define	AT91_PIN_PC31	(0x40 + 31)
-
-#define	AT91_PIN_PD0	(0x60 + 0)
-#define	AT91_PIN_PD1	(0x60 + 1)
-#define	AT91_PIN_PD2	(0x60 + 2)
-#define	AT91_PIN_PD3	(0x60 + 3)
-#define	AT91_PIN_PD4	(0x60 + 4)
-#define	AT91_PIN_PD5	(0x60 + 5)
-#define	AT91_PIN_PD6	(0x60 + 6)
-#define	AT91_PIN_PD7	(0x60 + 7)
-#define	AT91_PIN_PD8	(0x60 + 8)
-#define	AT91_PIN_PD9	(0x60 + 9)
-#define	AT91_PIN_PD10	(0x60 + 10)
-#define	AT91_PIN_PD11	(0x60 + 11)
-#define	AT91_PIN_PD12	(0x60 + 12)
-#define	AT91_PIN_PD13	(0x60 + 13)
-#define	AT91_PIN_PD14	(0x60 + 14)
-#define	AT91_PIN_PD15	(0x60 + 15)
-#define	AT91_PIN_PD16	(0x60 + 16)
-#define	AT91_PIN_PD17	(0x60 + 17)
-#define	AT91_PIN_PD18	(0x60 + 18)
-#define	AT91_PIN_PD19	(0x60 + 19)
-#define	AT91_PIN_PD20	(0x60 + 20)
-#define	AT91_PIN_PD21	(0x60 + 21)
-#define	AT91_PIN_PD22	(0x60 + 22)
-#define	AT91_PIN_PD23	(0x60 + 23)
-#define	AT91_PIN_PD24	(0x60 + 24)
-#define	AT91_PIN_PD25	(0x60 + 25)
-#define	AT91_PIN_PD26	(0x60 + 26)
-#define	AT91_PIN_PD27	(0x60 + 27)
-#define	AT91_PIN_PD28	(0x60 + 28)
-#define	AT91_PIN_PD29	(0x60 + 29)
-#define	AT91_PIN_PD30	(0x60 + 30)
-#define	AT91_PIN_PD31	(0x60 + 31)
-
-#define	AT91_PIN_PE0	(0x80 + 0)
-#define	AT91_PIN_PE1	(0x80 + 1)
-#define	AT91_PIN_PE2	(0x80 + 2)
-#define	AT91_PIN_PE3	(0x80 + 3)
-#define	AT91_PIN_PE4	(0x80 + 4)
-#define	AT91_PIN_PE5	(0x80 + 5)
-#define	AT91_PIN_PE6	(0x80 + 6)
-#define	AT91_PIN_PE7	(0x80 + 7)
-#define	AT91_PIN_PE8	(0x80 + 8)
-#define	AT91_PIN_PE9	(0x80 + 9)
-#define	AT91_PIN_PE10	(0x80 + 10)
-#define	AT91_PIN_PE11	(0x80 + 11)
-#define	AT91_PIN_PE12	(0x80 + 12)
-#define	AT91_PIN_PE13	(0x80 + 13)
-#define	AT91_PIN_PE14	(0x80 + 14)
-#define	AT91_PIN_PE15	(0x80 + 15)
-#define	AT91_PIN_PE16	(0x80 + 16)
-#define	AT91_PIN_PE17	(0x80 + 17)
-#define	AT91_PIN_PE18	(0x80 + 18)
-#define	AT91_PIN_PE19	(0x80 + 19)
-#define	AT91_PIN_PE20	(0x80 + 20)
-#define	AT91_PIN_PE21	(0x80 + 21)
-#define	AT91_PIN_PE22	(0x80 + 22)
-#define	AT91_PIN_PE23	(0x80 + 23)
-#define	AT91_PIN_PE24	(0x80 + 24)
-#define	AT91_PIN_PE25	(0x80 + 25)
-#define	AT91_PIN_PE26	(0x80 + 26)
-#define	AT91_PIN_PE27	(0x80 + 27)
-#define	AT91_PIN_PE28	(0x80 + 28)
-#define	AT91_PIN_PE29	(0x80 + 29)
-#define	AT91_PIN_PE30	(0x80 + 30)
-#define	AT91_PIN_PE31	(0x80 + 31)
-
-#ifndef __ASSEMBLY__
-/* setup setup routines, called from board init or driver probe() */
-extern int __init_or_module at91_set_GPIO_periph(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_C_periph(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_D_periph(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_gpio_output(unsigned pin, int value);
-extern int __init_or_module at91_set_deglitch(unsigned pin, int is_on);
-extern int __init_or_module at91_set_debounce(unsigned pin, int is_on, int div);
-extern int __init_or_module at91_set_multi_drive(unsigned pin, int is_on);
-extern int __init_or_module at91_set_pulldown(unsigned pin, int is_on);
-extern int __init_or_module at91_disable_schmitt_trig(unsigned pin);
-
-/* callable at any time */
-extern int at91_set_gpio_value(unsigned pin, int value);
-extern int at91_get_gpio_value(unsigned pin);
-
-/* callable only from core power-management code */
-extern void at91_gpio_suspend(void);
-extern void at91_gpio_resume(void);
-
-#endif	/* __ASSEMBLY__ */
-
-#endif

arch/arm/mach-at91/gsia18s.h

@@ -1,33 +0,0 @@
-/* Buttons */
-#define GPIO_TRIG_NET_IN		AT91_PIN_PB21
-#define GPIO_CARD_UNMOUNT_0		AT91_PIN_PB13
-#define GPIO_CARD_UNMOUNT_1		AT91_PIN_PB12
-#define GPIO_KEY_POWER			AT91_PIN_PA25
-
-/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */
-#define GS_IA18_S_PCF_GPIO_BASE0	NR_BUILTIN_GPIO
-#define PCF_GPIO_HDC_POWER		(GS_IA18_S_PCF_GPIO_BASE0 + 0)
-#define PCF_GPIO_WIFI_SETUP		(GS_IA18_S_PCF_GPIO_BASE0 + 1)
-#define PCF_GPIO_WIFI_ENABLE		(GS_IA18_S_PCF_GPIO_BASE0 + 2)
-#define PCF_GPIO_WIFI_RESET		(GS_IA18_S_PCF_GPIO_BASE0 + 3)
-#define PCF_GPIO_ETH_DETECT		4 /* this is a GPI */
-#define PCF_GPIO_GPS_SETUP		(GS_IA18_S_PCF_GPIO_BASE0 + 5)
-#define PCF_GPIO_GPS_STANDBY		(GS_IA18_S_PCF_GPIO_BASE0 + 6)
-#define PCF_GPIO_GPS_POWER		(GS_IA18_S_PCF_GPIO_BASE0 + 7)
-
-/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */
-#define GS_IA18_S_PCF_GPIO_BASE1	(GS_IA18_S_PCF_GPIO_BASE0 + 8)
-#define PCF_GPIO_ALARM1			(GS_IA18_S_PCF_GPIO_BASE1 + 0)
-#define PCF_GPIO_ALARM2			(GS_IA18_S_PCF_GPIO_BASE1 + 1)
-#define PCF_GPIO_ALARM3			(GS_IA18_S_PCF_GPIO_BASE1 + 2)
-#define PCF_GPIO_ALARM4			(GS_IA18_S_PCF_GPIO_BASE1 + 3)
-/* bits 4, 5, 6 not used */
-#define PCF_GPIO_ALARM_V_RELAY_ON	(GS_IA18_S_PCF_GPIO_BASE1 + 7)
-
-/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */
-#define GS_IA18_S_PCF_GPIO_BASE2	(GS_IA18_S_PCF_GPIO_BASE1 + 8)
-#define PCF_GPIO_MODEM_POWER		(GS_IA18_S_PCF_GPIO_BASE2 + 0)
-#define PCF_GPIO_MODEM_RESET		(GS_IA18_S_PCF_GPIO_BASE2 + 3)
-/* bits 1, 2, 4, 5 not used */
-#define PCF_GPIO_TRX_RESET		(GS_IA18_S_PCF_GPIO_BASE2 + 6)
-/* bit 7 not used */

arch/arm/mach-at91/include/mach/at91_ramc.h

@@ -25,8 +25,8 @@ extern void __iomem *at91_ramc_base[];
 #define AT91_MEMCTRL_SDRAMC	1
 #define AT91_MEMCTRL_DDRSDR	2
 
-#include <mach/at91rm9200_sdramc.h>
-#include <mach/at91sam9_ddrsdr.h>
-#include <mach/at91sam9_sdramc.h>
+#include <soc/at91/at91rm9200_sdramc.h>
+#include <soc/at91/at91sam9_ddrsdr.h>
+#include <soc/at91/at91sam9_sdramc.h>
 
 #endif /* __AT91_RAMC_H__ */

arch/arm/mach-at91/include/mach/hardware.h

@@ -127,13 +127,8 @@
  * called as part of the generic suspend/resume path.
  */
 #ifndef __ASSEMBLY__
-#ifdef CONFIG_PINCTRL_AT91
 extern void at91_pinctrl_gpio_suspend(void);
 extern void at91_pinctrl_gpio_resume(void);
-#else
-static inline void at91_pinctrl_gpio_suspend(void) {}
-static inline void at91_pinctrl_gpio_resume(void) {}
-#endif
 #endif
 
 #endif

arch/arm/mach-at91/irq.c

@@ -1,296 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/irq.c
- *
- *  Copyright (C) 2004 SAN People
- *  Copyright (C) 2004 ATMEL
- *  Copyright (C) Rick Bronson
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/mm.h>
-#include <linux/bitmap.h>
-#include <linux/types.h>
-#include <linux/irq.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/of_irq.h>
-#include <linux/irqdomain.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/setup.h>
-
-#include <asm/exception.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/map.h>
-
-#include "at91_aic.h"
-
-void __iomem *at91_aic_base;
-static struct irq_domain *at91_aic_domain;
-static struct device_node *at91_aic_np;
-static unsigned int n_irqs = NR_AIC_IRQS;
-
-#ifdef CONFIG_PM
-
-static unsigned long *wakeups;
-static unsigned long *backups;
-
-#define set_backup(bit) set_bit(bit, backups)
-#define clear_backup(bit) clear_bit(bit, backups)
-
-static int at91_aic_pm_init(void)
-{
-	backups = kzalloc(BITS_TO_LONGS(n_irqs) * sizeof(*backups), GFP_KERNEL);
-	if (!backups)
-		return -ENOMEM;
-
-	wakeups = kzalloc(BITS_TO_LONGS(n_irqs) * sizeof(*backups), GFP_KERNEL);
-	if (!wakeups) {
-		kfree(backups);
-		return -ENOMEM;
-	}
-
-	return 0;
-}
-
-static int at91_aic_set_wake(struct irq_data *d, unsigned value)
-{
-	if (unlikely(d->hwirq >= n_irqs))
-		return -EINVAL;
-
-	if (value)
-		set_bit(d->hwirq, wakeups);
-	else
-		clear_bit(d->hwirq, wakeups);
-
-	return 0;
-}
-
-void at91_irq_suspend(void)
-{
-	at91_aic_write(AT91_AIC_IDCR, *backups);
-	at91_aic_write(AT91_AIC_IECR, *wakeups);
-}
-
-void at91_irq_resume(void)
-{
-	at91_aic_write(AT91_AIC_IDCR, *wakeups);
-	at91_aic_write(AT91_AIC_IECR, *backups);
-}
-
-#else
-static inline int at91_aic_pm_init(void)
-{
-	return 0;
-}
-
-#define set_backup(bit)
-#define clear_backup(bit)
-#define at91_aic_set_wake	NULL
-
-#endif /* CONFIG_PM */
-
-asmlinkage void __exception_irq_entry
-at91_aic_handle_irq(struct pt_regs *regs)
-{
-	u32 irqnr;
-	u32 irqstat;
-
-	irqnr = at91_aic_read(AT91_AIC_IVR);
-	irqstat = at91_aic_read(AT91_AIC_ISR);
-
-	/*
-	 * ISR value is 0 when there is no current interrupt or when there is
-	 * a spurious interrupt
-	 */
-	if (!irqstat)
-		at91_aic_write(AT91_AIC_EOICR, 0);
-	else
-		handle_IRQ(irqnr, regs);
-}
-
-static void at91_aic_mask_irq(struct irq_data *d)
-{
-	/* Disable interrupt on AIC */
-	at91_aic_write(AT91_AIC_IDCR, 1 << d->hwirq);
-	/* Update ISR cache */
-	clear_backup(d->hwirq);
-}
-
-static void at91_aic_unmask_irq(struct irq_data *d)
-{
-	/* Enable interrupt on AIC */
-	at91_aic_write(AT91_AIC_IECR, 1 << d->hwirq);
-	/* Update ISR cache */
-	set_backup(d->hwirq);
-}
-
-static void at91_aic_eoi(struct irq_data *d)
-{
-	/*
-	 * Mark end-of-interrupt on AIC, the controller doesn't care about
-	 * the value written. Moreover it's a write-only register.
-	 */
-	at91_aic_write(AT91_AIC_EOICR, 0);
-}
-
-static unsigned long *at91_extern_irq;
-
-u32 at91_get_extern_irq(void)
-{
-	if (!at91_extern_irq)
-		return 0;
-	return *at91_extern_irq;
-}
-
-#define is_extern_irq(hwirq) test_bit(hwirq, at91_extern_irq)
-
-static int at91_aic_compute_srctype(struct irq_data *d, unsigned type)
-{
-	int srctype;
-
-	switch (type) {
-	case IRQ_TYPE_LEVEL_HIGH:
-		srctype = AT91_AIC_SRCTYPE_HIGH;
-		break;
-	case IRQ_TYPE_EDGE_RISING:
-		srctype = AT91_AIC_SRCTYPE_RISING;
-		break;
-	case IRQ_TYPE_LEVEL_LOW:
-		if ((d->hwirq == AT91_ID_FIQ) || is_extern_irq(d->hwirq))		/* only supported on external interrupts */
-			srctype = AT91_AIC_SRCTYPE_LOW;
-		else
-			srctype = -EINVAL;
-		break;
-	case IRQ_TYPE_EDGE_FALLING:
-		if ((d->hwirq == AT91_ID_FIQ) || is_extern_irq(d->hwirq))		/* only supported on external interrupts */
-			srctype = AT91_AIC_SRCTYPE_FALLING;
-		else
-			srctype = -EINVAL;
-		break;
-	default:
-		srctype = -EINVAL;
-	}
-
-	return srctype;
-}
-
-static int at91_aic_set_type(struct irq_data *d, unsigned type)
-{
-	unsigned int smr;
-	int srctype;
-
-	srctype = at91_aic_compute_srctype(d, type);
-	if (srctype < 0)
-		return srctype;
-
-	smr = at91_aic_read(AT91_AIC_SMR(d->hwirq)) & ~AT91_AIC_SRCTYPE;
-	at91_aic_write(AT91_AIC_SMR(d->hwirq), smr | srctype);
-
-	return 0;
-}
-
-static struct irq_chip at91_aic_chip = {
-	.name		= "AIC",
-	.irq_mask	= at91_aic_mask_irq,
-	.irq_unmask	= at91_aic_unmask_irq,
-	.irq_set_type	= at91_aic_set_type,
-	.irq_set_wake	= at91_aic_set_wake,
-	.irq_eoi	= at91_aic_eoi,
-};
-
-static void __init at91_aic_hw_init(unsigned int spu_vector)
-{
-	int i;
-
-	/*
-	 * Perform 8 End Of Interrupt Command to make sure AIC
-	 * will not Lock out nIRQ
-	 */
-	for (i = 0; i < 8; i++)
-		at91_aic_write(AT91_AIC_EOICR, 0);
-
-	/*
-	 * Spurious Interrupt ID in Spurious Vector Register.
-	 * When there is no current interrupt, the IRQ Vector Register
-	 * reads the value stored in AIC_SPU
-	 */
-	at91_aic_write(AT91_AIC_SPU, spu_vector);
-
-	/* No debugging in AIC: Debug (Protect) Control Register */
-	at91_aic_write(AT91_AIC_DCR, 0);
-
-	/* Disable and clear all interrupts initially */
-	at91_aic_write(AT91_AIC_IDCR, 0xFFFFFFFF);
-	at91_aic_write(AT91_AIC_ICCR, 0xFFFFFFFF);
-}
-
-/*
- * Initialize the AIC interrupt controller.
- */
-void __init at91_aic_init(unsigned int *priority, unsigned int ext_irq_mask)
-{
-	unsigned int i;
-	int irq_base;
-
-	at91_extern_irq = kzalloc(BITS_TO_LONGS(n_irqs)
-				  * sizeof(*at91_extern_irq), GFP_KERNEL);
-
-	if (at91_aic_pm_init() || at91_extern_irq == NULL)
-		panic("Unable to allocate bit maps\n");
-
-	*at91_extern_irq = ext_irq_mask;
-
-	at91_aic_base = ioremap(AT91_AIC, 512);
-	if (!at91_aic_base)
-		panic("Unable to ioremap AIC registers\n");
-
-	/* Add irq domain for AIC */
-	irq_base = irq_alloc_descs(-1, 0, n_irqs, 0);
-	if (irq_base < 0) {
-		WARN(1, "Cannot allocate irq_descs, assuming pre-allocated\n");
-		irq_base = 0;
-	}
-	at91_aic_domain = irq_domain_add_legacy(at91_aic_np, n_irqs,
-						irq_base, 0,
-						&irq_domain_simple_ops, NULL);
-
-	if (!at91_aic_domain)
-		panic("Unable to add AIC irq domain\n");
-
-	irq_set_default_host(at91_aic_domain);
-
-	/*
-	 * The IVR is used by macro get_irqnr_and_base to read and verify.
-	 * The irq number is NR_AIC_IRQS when a spurious interrupt has occurred.
-	 */
-	for (i = 0; i < n_irqs; i++) {
-		/* Put hardware irq number in Source Vector Register: */
-		at91_aic_write(AT91_AIC_SVR(i), NR_IRQS_LEGACY + i);
-		/* Active Low interrupt, with the specified priority */
-		at91_aic_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]);
-		irq_set_chip_and_handler(NR_IRQS_LEGACY + i, &at91_aic_chip, handle_fasteoi_irq);
-		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
-	}
-
-	at91_aic_hw_init(n_irqs);
-}

arch/arm/mach-at91/leds.c

@@ -1,56 +0,0 @@
-/*
- * LED driver for Atmel AT91-based boards.
- *
- *  Copyright (C) SAN People (Pty) Ltd
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
-*/
-
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-
-#include "board.h"
-#include "gpio.h"
-
-
-/* ------------------------------------------------------------------------- */
-
-#if defined(CONFIG_NEW_LEDS)
-
-/*
- * New cross-platform LED support.
- */
-
-static struct gpio_led_platform_data led_data;
-
-static struct platform_device at91_gpio_leds_device = {
-	.name			= "leds-gpio",
-	.id			= -1,
-	.dev.platform_data	= &led_data,
-};
-
-void __init at91_gpio_leds(struct gpio_led *leds, int nr)
-{
-	int i;
-
-	if (!nr)
-		return;
-
-	for (i = 0; i < nr; i++)
-		at91_set_gpio_output(leds[i].gpio, leds[i].active_low);
-
-	led_data.leds = leds;
-	led_data.num_leds = nr;
-	platform_device_register(&at91_gpio_leds_device);
-}
-
-#else
-void __init at91_gpio_leds(struct gpio_led *leds, int nr) {}
-#endif
-

arch/arm/mach-at91/pm.c

@@ -29,10 +29,8 @@
 #include <mach/cpu.h>
 #include <mach/hardware.h>
 
-#include "at91_aic.h"
 #include "generic.h"
 #include "pm.h"
-#include "gpio.h"
 
 static void (*at91_pm_standby)(void);
 
@@ -131,23 +129,7 @@ extern u32 at91_slow_clock_sz;
 
 static int at91_pm_enter(suspend_state_t state)
 {
-	if (of_have_populated_dt())
-		at91_pinctrl_gpio_suspend();
-	else
-		at91_gpio_suspend();
-
-	if (IS_ENABLED(CONFIG_OLD_IRQ_AT91) && at91_aic_base) {
-		at91_irq_suspend();
-
-		pr_debug("AT91: PM - wake mask %08x, pm state %d\n",
-				/* remember all the always-wake irqs */
-				(at91_pmc_read(AT91_PMC_PCSR)
-						| (1 << AT91_ID_FIQ)
-						| (1 << AT91_ID_SYS)
-						| (at91_get_extern_irq()))
-					& at91_aic_read(AT91_AIC_IMR),
-				state);
-	}
+	at91_pinctrl_gpio_suspend();
 
 	switch (state) {
 		/*
@@ -212,21 +194,10 @@ static int at91_pm_enter(suspend_state_t state)
 			goto error;
 	}
 
-	if (IS_ENABLED(CONFIG_OLD_IRQ_AT91) && at91_aic_base)
-		pr_debug("AT91: PM - wakeup %08x\n",
-			 at91_aic_read(AT91_AIC_IPR) &
-			 at91_aic_read(AT91_AIC_IMR));
-
 error:
 	target_state = PM_SUSPEND_ON;
 
-	if (IS_ENABLED(CONFIG_OLD_IRQ_AT91) && at91_aic_base)
-		at91_irq_resume();
-
-	if (of_have_populated_dt())
-		at91_pinctrl_gpio_resume();
-	else
-		at91_gpio_resume();
+	at91_pinctrl_gpio_resume();
 	return 0;
 }
 

arch/arm/mach-at91/pm.h

@@ -14,7 +14,6 @@
 #include <asm/proc-fns.h>
 
 #include <mach/at91_ramc.h>
-#include <mach/at91rm9200_sdramc.h>
 
 #ifdef CONFIG_PM
 extern void at91_pm_set_standby(void (*at91_standby)(void));

arch/arm/mach-at91/setup.c

@@ -42,35 +42,9 @@ void __init at91rm9200_set_type(int type)
 		at91_get_soc_subtype(&at91_soc_initdata));
 }
 
-void __init at91_init_irq_default(void)
-{
-	at91_init_interrupts(at91_boot_soc.default_irq_priority);
-}
-
-void __init at91_init_interrupts(unsigned int *priority)
-{
-	/* Initialize the AIC interrupt controller */
-	if (IS_ENABLED(CONFIG_OLD_IRQ_AT91))
-		at91_aic_init(priority, at91_boot_soc.extern_irq);
-
-	/* Enable GPIO interrupts */
-	at91_gpio_irq_setup();
-}
-
 void __iomem *at91_ramc_base[2];
 EXPORT_SYMBOL_GPL(at91_ramc_base);
 
-void __init at91_ioremap_ramc(int id, u32 addr, u32 size)
-{
-	if (id < 0 || id > 1) {
-		pr_emerg("Wrong RAM controller id (%d), cannot continue\n", id);
-		BUG();
-	}
-	at91_ramc_base[id] = ioremap(addr, size);
-	if (!at91_ramc_base[id])
-		panic(pr_fmt("Impossible to ioremap ramc.%d 0x%x\n"), id, addr);
-}
-
 static struct map_desc sram_desc[2] __initdata;
 
 void __init at91_init_sram(int bank, unsigned long base, unsigned int length)
@@ -418,7 +392,6 @@ void __init at91_ioremap_matrix(u32 base_addr)
 		panic(pr_fmt("Impossible to ioremap at91_matrix_base\n"));
 }
 
-#if defined(CONFIG_OF)
 static struct of_device_id ramc_ids[] = {
 	{ .compatible = "atmel,at91rm9200-sdramc", .data = at91rm9200_standby },
 	{ .compatible = "atmel,at91sam9260-sdramc", .data = at91sam9_sdram_standby },
@@ -460,13 +433,6 @@ void __init at91rm9200_dt_initialize(void)
 {
 	at91_dt_ramc();
 
-	/* Init clock subsystem */
-	at91_dt_clock_init();
-
-	/* Register the processor-specific clocks */
-	if (at91_boot_soc.register_clocks)
-		at91_boot_soc.register_clocks();
-
 	at91_boot_soc.init();
 }
 
@@ -474,39 +440,6 @@ void __init at91_dt_initialize(void)
 {
 	at91_dt_ramc();
 
-	/* Init clock subsystem */
-	at91_dt_clock_init();
-
-	/* Register the processor-specific clocks */
-	if (at91_boot_soc.register_clocks)
-		at91_boot_soc.register_clocks();
-
 	if (at91_boot_soc.init)
 		at91_boot_soc.init();
 }
-#endif
-
-void __init at91_initialize(unsigned long main_clock)
-{
-	at91_boot_soc.ioremap_registers();
-
-	/* Init clock subsystem */
-	at91_clock_init(main_clock);
-
-	/* Register the processor-specific clocks */
-	at91_boot_soc.register_clocks();
-
-	at91_boot_soc.init();
-
-	pinctrl_provide_dummies();
-}
-
-void __init at91_register_devices(void)
-{
-	at91_boot_soc.register_devices();
-}
-
-void __init at91_init_time(void)
-{
-	at91_boot_soc.init_time();
-}

arch/arm/mach-at91/soc.h

@@ -6,14 +6,8 @@
 
 struct at91_init_soc {
 	int builtin;
-	u32 extern_irq;
-	unsigned int *default_irq_priority;
 	void (*map_io)(void);
-	void (*ioremap_registers)(void);
-	void (*register_clocks)(void);
-	void (*register_devices)(void);
 	void (*init)(void);
-	void (*init_time)(void);
 };
 
 extern struct at91_init_soc at91_boot_soc;

arch/arm/mach-at91/stamp9g20.h

@@ -1,7 +0,0 @@
-#ifndef __MACH_STAMP9G20_H
-#define __MACH_STAMP9G20_H
-
-void stamp9g20_init_early(void);
-void stamp9g20_board_init(void);
-
-#endif

drivers/clocksource/timer-atmel-pit.c

@@ -262,35 +262,3 @@ static void __init at91sam926x_pit_dt_init(struct device_node *node)
 }
 CLOCKSOURCE_OF_DECLARE(at91sam926x_pit, "atmel,at91sam9260-pit",
 		       at91sam926x_pit_dt_init);
-
-static void __iomem *pit_base_addr;
-
-void __init at91sam926x_pit_init(int irq)
-{
-	struct pit_data *data;
-
-	data = kzalloc(sizeof(*data), GFP_KERNEL);
-	if (!data)
-		panic(pr_fmt("Unable to allocate memory\n"));
-
-	data->base = pit_base_addr;
-
-	data->mck = clk_get(NULL, "mck");
-	if (IS_ERR(data->mck))
-		panic(pr_fmt("Unable to get mck clk\n"));
-
-	data->irq = irq;
-
-	at91sam926x_pit_common_init(data);
-}
-
-void __init at91sam926x_ioremap_pit(u32 addr)
-{
-	if (of_have_populated_dt())
-		return;
-
-	pit_base_addr = ioremap(addr, 16);
-
-	if (!pit_base_addr)
-		panic(pr_fmt("Impossible to ioremap PIT\n"));
-}

drivers/misc/Kconfig

@@ -75,7 +75,7 @@ config ATMEL_TCB_CLKSRC
 config ATMEL_TCB_CLKSRC_BLOCK
 	int
 	depends on ATMEL_TCB_CLKSRC
-	prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
+	prompt "TC Block" if CPU_AT32AP700X
 	default 0
 	range 0 1
 	help

drivers/net/ethernet/cadence/Kconfig

@@ -22,7 +22,7 @@ if NET_CADENCE
 
 config ARM_AT91_ETHER
 	tristate "AT91RM9200 Ethernet support"
-	depends on HAS_DMA && (ARCH_AT91RM9200 || COMPILE_TEST)
+	depends on HAS_DMA && (ARCH_AT91 || COMPILE_TEST)
 	select MACB
 	---help---
 	  If you wish to compile a kernel for the AT91RM9200 and enable

drivers/power/reset/at91-reset.c

@@ -19,8 +19,8 @@
 
 #include <asm/system_misc.h>
 
-#include <mach/at91sam9_ddrsdr.h>
-#include <mach/at91sam9_sdramc.h>
+#include <soc/at91/at91sam9_ddrsdr.h>
+#include <soc/at91/at91sam9_sdramc.h>
 
 #define AT91_RSTC_CR	0x00		/* Reset Controller Control Register */
 #define AT91_RSTC_PROCRST	BIT(0)		/* Processor Reset */

drivers/rtc/Kconfig

@@ -1110,7 +1110,7 @@ config RTC_DRV_AT91RM9200
 
 config RTC_DRV_AT91SAM9
 	tristate "AT91SAM9 RTT as RTC"
-	depends on ARCH_AT91 && !ARCH_AT91RM9200
+	depends on ARCH_AT91
 	select MFD_SYSCON
 	help
 	  Some AT91SAM9 SoCs provide an RTT (Real Time Timer) block which
@@ -1126,7 +1126,6 @@ config RTC_DRV_AT91SAM9_RTT
 	int
 	range 0 1
 	default 0
-	prompt "RTT module Number" if ARCH_AT91SAM9263
 	depends on RTC_DRV_AT91SAM9
 	help
 	  This option is only relevant for legacy board support and
@@ -1138,8 +1137,7 @@ config RTC_DRV_AT91SAM9_RTT
 
 config RTC_DRV_AT91SAM9_GPBR
 	int
-	range 0 3 if !ARCH_AT91SAM9263
-	range 0 15 if ARCH_AT91SAM9263
+	range 0 3
 	default 0
 	prompt "Backup Register Number"
 	depends on RTC_DRV_AT91SAM9

drivers/video/backlight/Kconfig

@@ -168,7 +168,6 @@ if BACKLIGHT_CLASS_DEVICE
 config BACKLIGHT_ATMEL_LCDC
 	bool "Atmel LCDC Contrast-as-Backlight control"
 	depends on FB_ATMEL
-	default y if MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK
 	help
 	  This provides a backlight control internal to the Atmel LCDC
 	  driver.  If the LCD "contrast control" on your board is wired

drivers/video/fbdev/Kconfig

@@ -999,23 +999,6 @@ config FB_ATMEL
 	help
 	  This enables support for the AT91/AT32 LCD Controller.
 
-config FB_INTSRAM
-	bool "Frame Buffer in internal SRAM"
-	depends on FB_ATMEL && ARCH_AT91SAM9261
-	help
-	  Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want
-	  to let frame buffer in external SDRAM.
-
-config FB_ATMEL_STN
-	bool "Use a STN display with AT91/AT32 LCD Controller"
-	depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK)
-	default n
-	help
-	  Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD
-	  Controller. Say N if you want to connect a TFT.
-
-	  If unsure, say N.
-
 config FB_NVIDIA
 	tristate "nVidia Framebuffer Support"
 	depends on FB && PCI

drivers/watchdog/Kconfig

@@ -154,14 +154,14 @@ config ARM_SP805_WATCHDOG
 
 config AT91RM9200_WATCHDOG
 	tristate "AT91RM9200 watchdog"
-	depends on ARCH_AT91RM9200
+	depends on SOC_AT91RM9200
 	help
 	  Watchdog timer embedded into AT91RM9200 chips. This will reboot your
 	  system when the timeout is reached.
 
 config AT91SAM9X_WATCHDOG
 	tristate "AT91SAM9X / AT91CAP9 watchdog"
-	depends on ARCH_AT91 && !ARCH_AT91RM9200
+	depends on ARCH_AT91
 	select WATCHDOG_CORE
 	help
 	  Watchdog timer embedded into AT91SAM9X and AT91CAP9 chips. This will