Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver specific changes from Arnd Bergmann:

 - Updates to the ux500 cpufreq code

 - Moving the u300 DMA controller driver to drivers/dma

 - Moving versatile express drivers out of arch/arm for sharing with arch/arm64

 - Device tree bindings for the OMAP General Purpose Memory Controller

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
  ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
  ARM: OMAP2+: gpmc: add DT bindings for OneNAND
  ARM: OMAP2+: gpmc-onenand: drop __init annotation
  mtd: omap-onenand: pass device_node in platform data
  ARM: OMAP2+: Prevent potential crash if GPMC probe fails
  ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
  arm: Move sp810.h to include/linux/amba/
  ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
  ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
  ARM: OMAP: gpmc-nand: drop __init annotation
  mtd: omap-nand: pass device_node in platform data
  ARM: OMAP: gpmc: don't create devices from initcall on DT
  dma: coh901318: cut down on platform data abstraction
  dma: coh901318: merge header files
  dma: coh901318: push definitions into driver
  dma: coh901318: push header down into the DMA subsystem
  dma: coh901318: skip hard-coded addresses
  dma: coh901318: remove hardcoded target addresses
  dma: coh901318: push platform data into driver
  dma: coh901318: create a proper platform data file
  ...

Documentation/devicetree/bindings/bus/ti-gpmc.txt

@@ -0,0 +1,84 @@
+Device tree bindings for OMAP general purpose memory controllers (GPMC)
+
+The actual devices are instantiated from the child nodes of a GPMC node.
+
+Required properties:
+
+ - compatible:		Should be set to one of the following:
+
+			ti,omap2420-gpmc (omap2420)
+			ti,omap2430-gpmc (omap2430)
+			ti,omap3430-gpmc (omap3430 & omap3630)
+			ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
+			ti,am3352-gpmc   (am335x devices)
+
+ - reg:			A resource specifier for the register space
+			(see the example below)
+ - ti,hwmods:		Should be set to "ti,gpmc" until the DT transition is
+			completed.
+ - #address-cells:	Must be set to 2 to allow memory address translation
+ - #size-cells:		Must be set to 1 to allow CS address passing
+ - gpmc,num-cs:		The maximum number of chip-select lines that controller
+			can support.
+ - gpmc,num-waitpins:	The maximum number of wait pins that controller can
+			support.
+ - ranges:		Must be set up to reflect the memory layout with four
+			integer values for each chip-select line in use:
+
+			   <cs-number> 0 <physical address of mapping> <size>
+
+			Currently, calculated values derived from the contents
+			of the per-CS register GPMC_CONFIG7 (as set up by the
+			bootloader) are used for the physical address decoding.
+			As this will change in the future, filling correct
+			values here is a requirement.
+
+Timing properties for child nodes. All are optional and default to 0.
+
+ - gpmc,sync-clk:	Minimum clock period for synchronous mode, in picoseconds
+
+ Chip-select signal timings corresponding to GPMC_CONFIG2:
+ - gpmc,cs-on:		Assertion time
+ - gpmc,cs-rd-off:	Read deassertion time
+ - gpmc,cs-wr-off:	Write deassertion time
+
+ ADV signal timings corresponding to GPMC_CONFIG3:
+ - gpmc,adv-on:		Assertion time
+ - gpmc,adv-rd-off:	Read deassertion time
+ - gpmc,adv-wr-off:	Write deassertion time
+
+ WE signals timings corresponding to GPMC_CONFIG4:
+ - gpmc,we-on:		Assertion time
+ - gpmc,we-off:		Deassertion time
+
+ OE signals timings corresponding to GPMC_CONFIG4:
+ - gpmc,oe-on:		Assertion time
+ - gpmc,oe-off:		Deassertion time
+
+ Access time and cycle time timings corresponding to GPMC_CONFIG5:
+ - gpmc,page-burst-access: Multiple access word delay
+ - gpmc,access:		Start-cycle to first data valid delay
+ - gpmc,rd-cycle:	Total read cycle time
+ - gpmc,wr-cycle:	Total write cycle time
+
+The following are only applicable to OMAP3+ and AM335x:
+ - gpmc,wr-access
+ - gpmc,wr-data-mux-bus
+
+
+Example for an AM33xx board:
+
+	gpmc: gpmc@50000000 {
+		compatible = "ti,am3352-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x50000000 0x2000>;
+		interrupts = <100>;
+
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <2>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+
+		/* child nodes go here */
+	};

Documentation/devicetree/bindings/mtd/gpmc-nand.txt

@@ -0,0 +1,80 @@
+Device tree bindings for GPMC connected NANDs
+
+GPMC connected NAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "nand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+For NAND specific properties such as ECC modes or bus width, please refer to
+Documentation/devicetree/bindings/mtd/nand.txt
+
+
+Required properties:
+
+ - reg:		The CS line the peripheral is connected to
+
+Optional properties:
+
+ - nand-bus-width: 		Set this numeric value to 16 if the hardware
+				is wired that way. If not specified, a bus
+				width of 8 is assumed.
+
+ - ti,nand-ecc-opt:		A string setting the ECC layout to use. One of:
+
+		"sw"		Software method (default)
+		"hw"		Hardware method
+		"hw-romcode"	gpmc hamming mode method & romcode layout
+		"bch4"		4-bit BCH ecc code
+		"bch8"		8-bit BCH ecc code
+
+ - elm_id:	Specifies elm device node. This is required to support BCH
+ 		error correction using ELM module.
+
+For inline partiton table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an AM33xx board:
+
+	gpmc: gpmc@50000000 {
+		compatible = "ti,am3352-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x50000000 0x1000000>;
+		interrupts = <100>;
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <2>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x2000>;	/* CS0: NAND */
+		elm_id = <&elm>;
+
+		nand@0,0 {
+			reg = <0 0 0>; /* CS0, offset 0 */
+			nand-bus-width = <16>;
+			ti,nand-ecc-opt = "bch8";
+
+			gpmc,sync-clk = <0>;
+			gpmc,cs-on = <0>;
+			gpmc,cs-rd-off = <44>;
+			gpmc,cs-wr-off = <44>;
+			gpmc,adv-on = <6>;
+			gpmc,adv-rd-off = <34>;
+			gpmc,adv-wr-off = <44>;
+			gpmc,we-off = <40>;
+			gpmc,oe-off = <54>;
+			gpmc,access = <64>;
+			gpmc,rd-cycle = <82>;
+			gpmc,wr-cycle = <82>;
+			gpmc,wr-access = <40>;
+			gpmc,wr-data-mux-bus = <0>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* partitions go here */
+		};
+	};
+

Documentation/devicetree/bindings/mtd/gpmc-onenand.txt

@@ -0,0 +1,43 @@
+Device tree bindings for GPMC connected OneNANDs
+
+GPMC connected OneNAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "onenand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Required properties:
+
+ - reg:			The CS line the peripheral is connected to
+
+Optional properties:
+
+ - dma-channel:		DMA Channel index
+
+For inline partiton table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an OMAP3430 board:
+
+	gpmc: gpmc@6e000000 {
+		compatible = "ti,omap3430-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x6e000000 0x1000000>;
+		interrupts = <20>;
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <4>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		onenand@0 {
+			reg = <0 0 0>; /* CS0, offset 0 */
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* partitions go here */
+		};
+	};

arch/arm/mach-omap2/gpmc-nand.c

@@ -89,20 +89,21 @@ static int omap2_nand_gpmc_retime(
 	return 0;
 }
 
-static bool __init gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
+static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
 {
 	/* support only OMAP3 class */
-	if (!cpu_is_omap34xx()) {
+	if (!cpu_is_omap34xx() && !soc_is_am33xx()) {
 		pr_err("BCH ecc is not supported on this CPU\n");
 		return 0;
 	}
 
 	/*
-	 * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1.
-	 * Other chips may be added if confirmed to work.
+	 * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1
+	 * and AM33xx derivates. Other chips may be added if confirmed to work.
 	 */
 	if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW) &&
-	    (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0))) {
+	    (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0)) &&
+	    (!soc_is_am33xx())) {
 		pr_err("BCH 4-bit mode is not supported on this CPU\n");
 		return 0;
 	}
@@ -110,8 +111,8 @@ static bool __init gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
 	return 1;
 }
 
-int __init gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
-			  struct gpmc_timings *gpmc_t)
+int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
+		   struct gpmc_timings *gpmc_t)
 {
 	int err	= 0;
 	struct device *dev = &gpmc_nand_device.dev;

arch/arm/mach-omap2/gpmc-onenand.c

@@ -356,7 +356,7 @@ static int gpmc_onenand_setup(void __iomem *onenand_base, int *freq_ptr)
 	return ret;
 }
 
-void __init gpmc_onenand_init(struct omap_onenand_platform_data *_onenand_data)
+void gpmc_onenand_init(struct omap_onenand_platform_data *_onenand_data)
 {
 	int err;
 

arch/arm/mach-omap2/gpmc.c

@@ -25,6 +25,10 @@
 #include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_mtd.h>
+#include <linux/of_device.h>
+#include <linux/mtd/nand.h>
 
 #include <linux/platform_data/mtd-nand-omap2.h>
 
@@ -34,6 +38,8 @@
 #include "common.h"
 #include "omap_device.h"
 #include "gpmc.h"
+#include "gpmc-nand.h"
+#include "gpmc-onenand.h"
 
 #define	DEVICE_NAME		"omap-gpmc"
 
@@ -145,7 +151,8 @@ static unsigned gpmc_irq_start;
 static struct resource	gpmc_mem_root;
 static struct resource	gpmc_cs_mem[GPMC_CS_NUM];
 static DEFINE_SPINLOCK(gpmc_mem_lock);
-static unsigned int gpmc_cs_map;	/* flag for cs which are initialized */
+/* Define chip-selects as reserved by default until probe completes */
+static unsigned int gpmc_cs_map = ((1 << GPMC_CS_NUM) - 1);
 static struct device *gpmc_dev;
 static int gpmc_irq;
 static resource_size_t phys_base, mem_size;
@@ -1118,9 +1125,216 @@ int gpmc_calc_timings(struct gpmc_timings *gpmc_t,
 	/* TODO: remove, see function definition */
 	gpmc_convert_ps_to_ns(gpmc_t);
 
+	/* Now the GPMC is initialised, unreserve the chip-selects */
+	gpmc_cs_map = 0;
+
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static struct of_device_id gpmc_dt_ids[] = {
+	{ .compatible = "ti,omap2420-gpmc" },
+	{ .compatible = "ti,omap2430-gpmc" },
+	{ .compatible = "ti,omap3430-gpmc" },	/* omap3430 & omap3630 */
+	{ .compatible = "ti,omap4430-gpmc" },	/* omap4430 & omap4460 & omap543x */
+	{ .compatible = "ti,am3352-gpmc" },	/* am335x devices */
+	{ }
+};
+MODULE_DEVICE_TABLE(of, gpmc_dt_ids);
+
+static void __maybe_unused gpmc_read_timings_dt(struct device_node *np,
+						struct gpmc_timings *gpmc_t)
+{
+	u32 val;
+
+	memset(gpmc_t, 0, sizeof(*gpmc_t));
+
+	/* minimum clock period for syncronous mode */
+	if (!of_property_read_u32(np, "gpmc,sync-clk", &val))
+		gpmc_t->sync_clk = val;
+
+	/* chip select timtings */
+	if (!of_property_read_u32(np, "gpmc,cs-on", &val))
+		gpmc_t->cs_on = val;
+
+	if (!of_property_read_u32(np, "gpmc,cs-rd-off", &val))
+		gpmc_t->cs_rd_off = val;
+
+	if (!of_property_read_u32(np, "gpmc,cs-wr-off", &val))
+		gpmc_t->cs_wr_off = val;
+
+	/* ADV signal timings */
+	if (!of_property_read_u32(np, "gpmc,adv-on", &val))
+		gpmc_t->adv_on = val;
+
+	if (!of_property_read_u32(np, "gpmc,adv-rd-off", &val))
+		gpmc_t->adv_rd_off = val;
+
+	if (!of_property_read_u32(np, "gpmc,adv-wr-off", &val))
+		gpmc_t->adv_wr_off = val;
+
+	/* WE signal timings */
+	if (!of_property_read_u32(np, "gpmc,we-on", &val))
+		gpmc_t->we_on = val;
+
+	if (!of_property_read_u32(np, "gpmc,we-off", &val))
+		gpmc_t->we_off = val;
+
+	/* OE signal timings */
+	if (!of_property_read_u32(np, "gpmc,oe-on", &val))
+		gpmc_t->oe_on = val;
+
+	if (!of_property_read_u32(np, "gpmc,oe-off", &val))
+		gpmc_t->oe_off = val;
+
+	/* access and cycle timings */
+	if (!of_property_read_u32(np, "gpmc,page-burst-access", &val))
+		gpmc_t->page_burst_access = val;
+
+	if (!of_property_read_u32(np, "gpmc,access", &val))
+		gpmc_t->access = val;
+
+	if (!of_property_read_u32(np, "gpmc,rd-cycle", &val))
+		gpmc_t->rd_cycle = val;
+
+	if (!of_property_read_u32(np, "gpmc,wr-cycle", &val))
+		gpmc_t->wr_cycle = val;
+
+	/* only for OMAP3430 */
+	if (!of_property_read_u32(np, "gpmc,wr-access", &val))
+		gpmc_t->wr_access = val;
+
+	if (!of_property_read_u32(np, "gpmc,wr-data-mux-bus", &val))
+		gpmc_t->wr_data_mux_bus = val;
+}
+
+#ifdef CONFIG_MTD_NAND
+
+static const char * const nand_ecc_opts[] = {
+	[OMAP_ECC_HAMMING_CODE_DEFAULT]		= "sw",
+	[OMAP_ECC_HAMMING_CODE_HW]		= "hw",
+	[OMAP_ECC_HAMMING_CODE_HW_ROMCODE]	= "hw-romcode",
+	[OMAP_ECC_BCH4_CODE_HW]			= "bch4",
+	[OMAP_ECC_BCH8_CODE_HW]			= "bch8",
+};
+
+static int gpmc_probe_nand_child(struct platform_device *pdev,
+				 struct device_node *child)
+{
+	u32 val;
+	const char *s;
+	struct gpmc_timings gpmc_t;
+	struct omap_nand_platform_data *gpmc_nand_data;
+
+	if (of_property_read_u32(child, "reg", &val) < 0) {
+		dev_err(&pdev->dev, "%s has no 'reg' property\n",
+			child->full_name);
+		return -ENODEV;
+	}
+
+	gpmc_nand_data = devm_kzalloc(&pdev->dev, sizeof(*gpmc_nand_data),
+				      GFP_KERNEL);
+	if (!gpmc_nand_data)
+		return -ENOMEM;
+
+	gpmc_nand_data->cs = val;
+	gpmc_nand_data->of_node = child;
+
+	if (!of_property_read_string(child, "ti,nand-ecc-opt", &s))
+		for (val = 0; val < ARRAY_SIZE(nand_ecc_opts); val++)
+			if (!strcasecmp(s, nand_ecc_opts[val])) {
+				gpmc_nand_data->ecc_opt = val;
+				break;
+			}
+
+	val = of_get_nand_bus_width(child);
+	if (val == 16)
+		gpmc_nand_data->devsize = NAND_BUSWIDTH_16;
+
+	gpmc_read_timings_dt(child, &gpmc_t);
+	gpmc_nand_init(gpmc_nand_data, &gpmc_t);
+
+	return 0;
+}
+#else
+static int gpmc_probe_nand_child(struct platform_device *pdev,
+				 struct device_node *child)
+{
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MTD_ONENAND
+static int gpmc_probe_onenand_child(struct platform_device *pdev,
+				 struct device_node *child)
+{
+	u32 val;
+	struct omap_onenand_platform_data *gpmc_onenand_data;
+
+	if (of_property_read_u32(child, "reg", &val) < 0) {
+		dev_err(&pdev->dev, "%s has no 'reg' property\n",
+			child->full_name);
+		return -ENODEV;
+	}
+
+	gpmc_onenand_data = devm_kzalloc(&pdev->dev, sizeof(*gpmc_onenand_data),
+					 GFP_KERNEL);
+	if (!gpmc_onenand_data)
+		return -ENOMEM;
+
+	gpmc_onenand_data->cs = val;
+	gpmc_onenand_data->of_node = child;
+	gpmc_onenand_data->dma_channel = -1;
+
+	if (!of_property_read_u32(child, "dma-channel", &val))
+		gpmc_onenand_data->dma_channel = val;
+
+	gpmc_onenand_init(gpmc_onenand_data);
+
+	return 0;
+}
+#else
+static int gpmc_probe_onenand_child(struct platform_device *pdev,
+				    struct device_node *child)
+{
+	return 0;
+}
+#endif
+
+static int gpmc_probe_dt(struct platform_device *pdev)
+{
+	int ret;
+	struct device_node *child;
+	const struct of_device_id *of_id =
+		of_match_device(gpmc_dt_ids, &pdev->dev);
+
+	if (!of_id)
+		return 0;
+
+	for_each_node_by_name(child, "nand") {
+		ret = gpmc_probe_nand_child(pdev, child);
+		if (ret < 0) {
+			of_node_put(child);
+			return ret;
+		}
+	}
+
+	for_each_node_by_name(child, "onenand") {
+		ret = gpmc_probe_onenand_child(pdev, child);
+		if (ret < 0) {
+			of_node_put(child);
+			return ret;
+		}
+	}
+	return 0;
+}
+#else
+static int gpmc_probe_dt(struct platform_device *pdev)
+{
+	return 0;
+}
+#endif
+
 static int gpmc_probe(struct platform_device *pdev)
 {
 	int rc;
@@ -1172,6 +1386,14 @@ static int gpmc_probe(struct platform_device *pdev)
 	if (IS_ERR_VALUE(gpmc_setup_irq()))
 		dev_warn(gpmc_dev, "gpmc_setup_irq failed\n");
 
+	rc = gpmc_probe_dt(pdev);
+	if (rc < 0) {
+		clk_disable_unprepare(gpmc_l3_clk);
+		clk_put(gpmc_l3_clk);
+		dev_err(gpmc_dev, "failed to probe DT parameters\n");
+		return rc;
+	}
+
 	return 0;
 }
 
@@ -1189,6 +1411,7 @@ static struct platform_driver gpmc_driver = {
 	.driver		= {
 		.name	= DEVICE_NAME,
 		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(gpmc_dt_ids),
 	},
 };
 
@@ -1212,6 +1435,13 @@ static int __init omap_gpmc_init(void)
 	struct platform_device *pdev;
 	char *oh_name = "gpmc";
 
+	/*
+	 * if the board boots up with a populated DT, do not
+	 * manually add the device from this initcall
+	 */
+	if (of_have_populated_dt())
+		return -ENODEV;
+
 	oh = omap_hwmod_lookup(oh_name);
 	if (!oh) {
 		pr_err("Could not look up %s\n", oh_name);

arch/arm/mach-u300/core.c

@@ -31,6 +31,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/platform_data/clk-u300.h>
 #include <linux/platform_data/pinctrl-coh901.h>
+#include <linux/platform_data/dma-coh901318.h>
 #include <linux/irqchip/arm-vic.h>
 
 #include <asm/types.h>
@@ -40,7 +41,6 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <mach/coh901318.h>
 #include <mach/hardware.h>
 #include <mach/syscon.h>
 #include <mach/irqs.h>
@@ -49,7 +49,6 @@
 #include "spi.h"
 #include "i2c.h"
 #include "u300-gpio.h"
-#include "dma_channels.h"
 
 /*
  * Static I/O mappings that are needed for booting the U300 platforms. The
@@ -327,1089 +326,6 @@ static struct resource dma_resource[] = {
 	}
 };
 
-/* points out all dma slave channels.
- * Syntax is [A1, B1, A2, B2, .... ,-1,-1]
- * Select all channels from A to B, end of list is marked with -1,-1
- */
-static int dma_slave_channels[] = {
-	U300_DMA_MSL_TX_0, U300_DMA_SPI_RX,
-	U300_DMA_UART1_TX, U300_DMA_UART1_RX, -1, -1};
-
-/* points out all dma memcpy channels. */
-static int dma_memcpy_channels[] = {
-	U300_DMA_GENERAL_PURPOSE_0, U300_DMA_GENERAL_PURPOSE_8, -1, -1};
-
-/** register dma for memory access
- *
- * active  1 means dma intends to access memory
- *         0 means dma wont access memory
- */
-static void coh901318_access_memory_state(struct device *dev, bool active)
-{
-}
-
-#define flags_memcpy_config (COH901318_CX_CFG_CH_DISABLE | \
-			COH901318_CX_CFG_RM_MEMORY_TO_MEMORY | \
-			COH901318_CX_CFG_LCR_DISABLE | \
-			COH901318_CX_CFG_TC_IRQ_ENABLE | \
-			COH901318_CX_CFG_BE_IRQ_ENABLE)
-#define flags_memcpy_lli_chained (COH901318_CX_CTRL_TC_ENABLE | \
-			COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
-			COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
-			COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
-			COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
-			COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
-			COH901318_CX_CTRL_MASTER_MODE_M1RW | \
-			COH901318_CX_CTRL_TCP_DISABLE | \
-			COH901318_CX_CTRL_TC_IRQ_DISABLE | \
-			COH901318_CX_CTRL_HSP_DISABLE | \
-			COH901318_CX_CTRL_HSS_DISABLE | \
-			COH901318_CX_CTRL_DDMA_LEGACY | \
-			COH901318_CX_CTRL_PRDD_SOURCE)
-#define flags_memcpy_lli (COH901318_CX_CTRL_TC_ENABLE | \
-			COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
-			COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
-			COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
-			COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
-			COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
-			COH901318_CX_CTRL_MASTER_MODE_M1RW | \
-			COH901318_CX_CTRL_TCP_DISABLE | \
-			COH901318_CX_CTRL_TC_IRQ_DISABLE | \
-			COH901318_CX_CTRL_HSP_DISABLE | \
-			COH901318_CX_CTRL_HSS_DISABLE | \
-			COH901318_CX_CTRL_DDMA_LEGACY | \
-			COH901318_CX_CTRL_PRDD_SOURCE)
-#define flags_memcpy_lli_last (COH901318_CX_CTRL_TC_ENABLE | \
-			COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
-			COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
-			COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
-			COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
-			COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
-			COH901318_CX_CTRL_MASTER_MODE_M1RW | \
-			COH901318_CX_CTRL_TCP_DISABLE | \
-			COH901318_CX_CTRL_TC_IRQ_ENABLE | \
-			COH901318_CX_CTRL_HSP_DISABLE | \
-			COH901318_CX_CTRL_HSS_DISABLE | \
-			COH901318_CX_CTRL_DDMA_LEGACY | \
-			COH901318_CX_CTRL_PRDD_SOURCE)
-
-const struct coh_dma_channel chan_config[U300_DMA_CHANNELS] = {
-	{
-		.number = U300_DMA_MSL_TX_0,
-		.name = "MSL TX 0",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 0 * 0x40 + 0x20,
-	},
-	{
-		.number = U300_DMA_MSL_TX_1,
-		.name = "MSL TX 1",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 1 * 0x40 + 0x20,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-	},
-	{
-		.number = U300_DMA_MSL_TX_2,
-		.name = "MSL TX 2",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 2 * 0x40 + 0x20,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.desc_nbr_max = 10,
-	},
-	{
-		.number = U300_DMA_MSL_TX_3,
-		.name = "MSL TX 3",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 3 * 0x40 + 0x20,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-	},
-	{
-		.number = U300_DMA_MSL_TX_4,
-		.name = "MSL TX 4",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 4 * 0x40 + 0x20,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-	},
-	{
-		.number = U300_DMA_MSL_TX_5,
-		.name = "MSL TX 5",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 5 * 0x40 + 0x20,
-	},
-	{
-		.number = U300_DMA_MSL_TX_6,
-		.name = "MSL TX 6",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 6 * 0x40 + 0x20,
-	},
-	{
-		.number = U300_DMA_MSL_RX_0,
-		.name = "MSL RX 0",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 0 * 0x40 + 0x220,
-	},
-	{
-		.number = U300_DMA_MSL_RX_1,
-		.name = "MSL RX 1",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 1 * 0x40 + 0x220,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli = 0,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-	},
-	{
-		.number = U300_DMA_MSL_RX_2,
-		.name = "MSL RX 2",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 2 * 0x40 + 0x220,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-	},
-	{
-		.number = U300_DMA_MSL_RX_3,
-		.name = "MSL RX 3",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 3 * 0x40 + 0x220,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-	},
-	{
-		.number = U300_DMA_MSL_RX_4,
-		.name = "MSL RX 4",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 4 * 0x40 + 0x220,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-	},
-	{
-		.number = U300_DMA_MSL_RX_5,
-		.name = "MSL RX 5",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 5 * 0x40 + 0x220,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
-				COH901318_CX_CTRL_PRDD_DEST,
-	},
-	{
-		.number = U300_DMA_MSL_RX_6,
-		.name = "MSL RX 6",
-		.priority_high = 0,
-		.dev_addr = U300_MSL_BASE + 6 * 0x40 + 0x220,
-	},
-	/*
-	 * Don't set up device address, burst count or size of src
-	 * or dst bus for this peripheral - handled by PrimeCell
-	 * DMA extension.
-	 */
-	{
-		.number = U300_DMA_MMCSD_RX_TX,
-		.name = "MMCSD RX TX",
-		.priority_high = 0,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-
-	},
-	{
-		.number = U300_DMA_MSPRO_TX,
-		.name = "MSPRO TX",
-		.priority_high = 0,
-	},
-	{
-		.number = U300_DMA_MSPRO_RX,
-		.name = "MSPRO RX",
-		.priority_high = 0,
-	},
-	/*
-	 * Don't set up device address, burst count or size of src
-	 * or dst bus for this peripheral - handled by PrimeCell
-	 * DMA extension.
-	 */
-	{
-		.number = U300_DMA_UART0_TX,
-		.name = "UART0 TX",
-		.priority_high = 0,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-	},
-	{
-		.number = U300_DMA_UART0_RX,
-		.name = "UART0 RX",
-		.priority_high = 0,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-	},
-	{
-		.number = U300_DMA_APEX_TX,
-		.name = "APEX TX",
-		.priority_high = 0,
-	},
-	{
-		.number = U300_DMA_APEX_RX,
-		.name = "APEX RX",
-		.priority_high = 0,
-	},
-	{
-		.number = U300_DMA_PCM_I2S0_TX,
-		.name = "PCM I2S0 TX",
-		.priority_high = 1,
-		.dev_addr = U300_PCM_I2S0_BASE + 0x14,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-	},
-	{
-		.number = U300_DMA_PCM_I2S0_RX,
-		.name = "PCM I2S0 RX",
-		.priority_high = 1,
-		.dev_addr = U300_PCM_I2S0_BASE + 0x10,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_DEST,
-	},
-	{
-		.number = U300_DMA_PCM_I2S1_TX,
-		.name = "PCM I2S1 TX",
-		.priority_high = 1,
-		.dev_addr =  U300_PCM_I2S1_BASE + 0x14,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_SOURCE,
-	},
-	{
-		.number = U300_DMA_PCM_I2S1_RX,
-		.name = "PCM I2S1 RX",
-		.priority_high = 1,
-		.dev_addr = U300_PCM_I2S1_BASE + 0x10,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_DEST,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
-				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
-				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
-				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_ENABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY |
-				COH901318_CX_CTRL_PRDD_DEST,
-	},
-	{
-		.number = U300_DMA_XGAM_CDI,
-		.name = "XGAM CDI",
-		.priority_high = 0,
-	},
-	{
-		.number = U300_DMA_XGAM_PDI,
-		.name = "XGAM PDI",
-		.priority_high = 0,
-	},
-	/*
-	 * Don't set up device address, burst count or size of src
-	 * or dst bus for this peripheral - handled by PrimeCell
-	 * DMA extension.
-	 */
-	{
-		.number = U300_DMA_SPI_TX,
-		.name = "SPI TX",
-		.priority_high = 0,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-	},
-	{
-		.number = U300_DMA_SPI_RX,
-		.name = "SPI RX",
-		.priority_high = 0,
-		.param.config = COH901318_CX_CFG_CH_DISABLE |
-				COH901318_CX_CFG_LCR_DISABLE |
-				COH901318_CX_CFG_TC_IRQ_ENABLE |
-				COH901318_CX_CFG_BE_IRQ_ENABLE,
-		.param.ctrl_lli_chained = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_DISABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-		.param.ctrl_lli_last = 0 |
-				COH901318_CX_CTRL_TC_ENABLE |
-				COH901318_CX_CTRL_MASTER_MODE_M1RW |
-				COH901318_CX_CTRL_TCP_DISABLE |
-				COH901318_CX_CTRL_TC_IRQ_ENABLE |
-				COH901318_CX_CTRL_HSP_ENABLE |
-				COH901318_CX_CTRL_HSS_DISABLE |
-				COH901318_CX_CTRL_DDMA_LEGACY,
-
-	},
-	{
-		.number = U300_DMA_GENERAL_PURPOSE_0,
-		.name = "GENERAL 00",
-		.priority_high = 0,
-
-		.param.config = flags_memcpy_config,
-		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
-		.param.ctrl_lli = flags_memcpy_lli,
-		.param.ctrl_lli_last = flags_memcpy_lli_last,
-	},
-	{
-		.number = U300_DMA_GENERAL_PURPOSE_1,
-		.name = "GENERAL 01",
-		.priority_high = 0,
-
-		.param.config = flags_memcpy_config,
-		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
-		.param.ctrl_lli = flags_memcpy_lli,
-		.param.ctrl_lli_last = flags_memcpy_lli_last,
-	},
-	{
-		.number = U300_DMA_GENERAL_PURPOSE_2,
-		.name = "GENERAL 02",
-		.priority_high = 0,
-
-		.param.config = flags_memcpy_config,
-		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
-		.param.ctrl_lli = flags_memcpy_lli,
-		.param.ctrl_lli_last = flags_memcpy_lli_last,
-	},
-	{
-		.number = U300_DMA_GENERAL_PURPOSE_3,
-		.name = "GENERAL 03",
-		.priority_high = 0,
-
-		.param.config = flags_memcpy_config,
-		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
-		.param.ctrl_lli = flags_memcpy_lli,
-		.param.ctrl_lli_last = flags_memcpy_lli_last,
-	},
-	{
-		.number = U300_DMA_GENERAL_PURPOSE_4,
-		.name = "GENERAL 04",
-		.priority_high = 0,
-
-		.param.config = flags_memcpy_config,
-		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
-		.param.ctrl_lli = flags_memcpy_lli,
-		.param.ctrl_lli_last = flags_memcpy_lli_last,
-	},
-	{
-		.number = U300_DMA_GENERAL_PURPOSE_5,
-		.name = "GENERAL 05",
-		.priority_high = 0,
-
-		.param.config = flags_memcpy_config,
-		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
-		.param.ctrl_lli = flags_memcpy_lli,
-		.param.ctrl_lli_last = flags_memcpy_lli_last,
-	},
-	{
-		.number = U300_DMA_GENERAL_PURPOSE_6,
-		.name = "GENERAL 06",
-		.priority_high = 0,
-
-		.param.config = flags_memcpy_config,
-		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
-		.param.ctrl_lli = flags_memcpy_lli,
-		.param.ctrl_lli_last = flags_memcpy_lli_last,
-	},
-	{
-		.number = U300_DMA_GENERAL_PURPOSE_7,
-		.name = "GENERAL 07",
-		.priority_high = 0,
-
-		.param.config = flags_memcpy_config,
-		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
-		.param.ctrl_lli = flags_memcpy_lli,
-		.param.ctrl_lli_last = flags_memcpy_lli_last,
-	},
-	{
-		.number = U300_DMA_GENERAL_PURPOSE_8,
-		.name = "GENERAL 08",
-		.priority_high = 0,
-
-		.param.config = flags_memcpy_config,
-		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
-		.param.ctrl_lli = flags_memcpy_lli,
-		.param.ctrl_lli_last = flags_memcpy_lli_last,
-	},
-	{
-		.number = U300_DMA_UART1_TX,
-		.name = "UART1 TX",
-		.priority_high = 0,
-	},
-	{
-		.number = U300_DMA_UART1_RX,
-		.name = "UART1 RX",
-		.priority_high = 0,
-	}
-};
-
-
-static struct coh901318_platform coh901318_platform = {
-	.chans_slave = dma_slave_channels,
-	.chans_memcpy = dma_memcpy_channels,
-	.access_memory_state = coh901318_access_memory_state,
-	.chan_conf = chan_config,
-	.max_channels = U300_DMA_CHANNELS,
-};
 
 static struct resource pinctrl_resources[] = {
 	{
@@ -1521,7 +437,6 @@ static struct platform_device dma_device = {
 	.resource	= dma_resource,
 	.num_resources  = ARRAY_SIZE(dma_resource),
 	.dev = {
-		.platform_data = &coh901318_platform,
 		.coherent_dma_mask = ~0,
 	},
 };

arch/arm/mach-u300/dma_channels.h

@@ -1,60 +0,0 @@
-/*
- *
- * arch/arm/mach-u300/include/mach/dma_channels.h
- *
- *
- * Copyright (C) 2007-2012 ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- * Map file for the U300 dma driver.
- * Author: Per Friden <per.friden@stericsson.com>
- */
-
-#ifndef DMA_CHANNELS_H
-#define DMA_CHANNELS_H
-
-#define U300_DMA_MSL_TX_0             0
-#define U300_DMA_MSL_TX_1             1
-#define U300_DMA_MSL_TX_2             2
-#define U300_DMA_MSL_TX_3             3
-#define U300_DMA_MSL_TX_4             4
-#define U300_DMA_MSL_TX_5             5
-#define U300_DMA_MSL_TX_6             6
-#define U300_DMA_MSL_RX_0             7
-#define U300_DMA_MSL_RX_1             8
-#define U300_DMA_MSL_RX_2             9
-#define U300_DMA_MSL_RX_3             10
-#define U300_DMA_MSL_RX_4             11
-#define U300_DMA_MSL_RX_5             12
-#define U300_DMA_MSL_RX_6             13
-#define U300_DMA_MMCSD_RX_TX          14
-#define U300_DMA_MSPRO_TX             15
-#define U300_DMA_MSPRO_RX             16
-#define U300_DMA_UART0_TX             17
-#define U300_DMA_UART0_RX             18
-#define U300_DMA_APEX_TX              19
-#define U300_DMA_APEX_RX              20
-#define U300_DMA_PCM_I2S0_TX          21
-#define U300_DMA_PCM_I2S0_RX          22
-#define U300_DMA_PCM_I2S1_TX          23
-#define U300_DMA_PCM_I2S1_RX          24
-#define U300_DMA_XGAM_CDI             25
-#define U300_DMA_XGAM_PDI             26
-#define U300_DMA_SPI_TX               27
-#define U300_DMA_SPI_RX               28
-#define U300_DMA_GENERAL_PURPOSE_0    29
-#define U300_DMA_GENERAL_PURPOSE_1    30
-#define U300_DMA_GENERAL_PURPOSE_2    31
-#define U300_DMA_GENERAL_PURPOSE_3    32
-#define U300_DMA_GENERAL_PURPOSE_4    33
-#define U300_DMA_GENERAL_PURPOSE_5    34
-#define U300_DMA_GENERAL_PURPOSE_6    35
-#define U300_DMA_GENERAL_PURPOSE_7    36
-#define U300_DMA_GENERAL_PURPOSE_8    37
-#define U300_DMA_UART1_TX             38
-#define U300_DMA_UART1_RX             39
-
-#define U300_DMA_DEVICE_CHANNELS      32
-#define U300_DMA_CHANNELS             40
-
-
-#endif /* DMA_CHANNELS_H */

arch/arm/mach-u300/include/mach/coh901318.h

@@ -1,267 +0,0 @@
-/*
- *
- * include/linux/coh901318.h
- *
- *
- * Copyright (C) 2007-2009 ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- * DMA driver for COH 901 318
- * Author: Per Friden <per.friden@stericsson.com>
- */
-
-#ifndef COH901318_H
-#define COH901318_H
-
-#include <linux/device.h>
-#include <linux/dmaengine.h>
-
-#define MAX_DMA_PACKET_SIZE_SHIFT 11
-#define MAX_DMA_PACKET_SIZE (1 << MAX_DMA_PACKET_SIZE_SHIFT)
-
-/**
- * struct coh901318_lli - linked list item for DMAC
- * @control: control settings for DMAC
- * @src_addr: transfer source address
- * @dst_addr: transfer destination address
- * @link_addr:  physical address to next lli
- * @virt_link_addr: virtual address of next lli (only used by pool_free)
- * @phy_this: physical address of current lli (only used by pool_free)
- */
-struct coh901318_lli {
-	u32 control;
-	dma_addr_t src_addr;
-	dma_addr_t dst_addr;
-	dma_addr_t link_addr;
-
-	void *virt_link_addr;
-	dma_addr_t phy_this;
-};
-/**
- * struct coh901318_params - parameters for DMAC configuration
- * @config: DMA config register
- * @ctrl_lli_last: DMA control register for the last lli in the list
- * @ctrl_lli: DMA control register for an lli
- * @ctrl_lli_chained: DMA control register for a chained lli
- */
-struct coh901318_params {
-	u32 config;
-	u32 ctrl_lli_last;
-	u32 ctrl_lli;
-	u32 ctrl_lli_chained;
-};
-/**
- * struct coh_dma_channel - dma channel base
- * @name: ascii name of dma channel
- * @number: channel id number
- * @desc_nbr_max: number of preallocated descriptors
- * @priority_high: prio of channel, 0 low otherwise high.
- * @param: configuration parameters
- * @dev_addr: physical address of periphal connected to channel
- */
-struct coh_dma_channel {
-	const char name[32];
-	const int number;
-	const int desc_nbr_max;
-	const int priority_high;
-	const struct coh901318_params param;
-	const dma_addr_t dev_addr;
-};
-
-/**
- * dma_access_memory_state_t - register dma for memory access
- *
- * @dev: The dma device
- * @active:  1 means dma intends to access memory
- *           0 means dma wont access memory
- */
-typedef void (*dma_access_memory_state_t)(struct device *dev,
-					  bool active);
-
-/**
- * struct powersave - DMA power save structure
- * @lock: lock protecting data in this struct
- * @started_channels: bit mask indicating active dma channels
- */
-struct powersave {
-	spinlock_t lock;
-	u64 started_channels;
-};
-/**
- * struct coh901318_platform - platform arch structure
- * @chans_slave: specifying dma slave channels
- * @chans_memcpy: specifying dma memcpy channels
- * @access_memory_state: requesting DMA memory access (on / off)
- * @chan_conf: dma channel configurations
- * @max_channels: max number of dma chanenls
- */
-struct coh901318_platform {
-	const int *chans_slave;
-	const int *chans_memcpy;
-	const dma_access_memory_state_t access_memory_state;
-	const struct coh_dma_channel *chan_conf;
-	const int max_channels;
-};
-
-#ifdef CONFIG_COH901318
-/**
- * coh901318_filter_id() - DMA channel filter function
- * @chan: dma channel handle
- * @chan_id: id of dma channel to be filter out
- *
- * In dma_request_channel() it specifies what channel id to be requested
- */
-bool coh901318_filter_id(struct dma_chan *chan, void *chan_id);
-#else
-static inline bool coh901318_filter_id(struct dma_chan *chan, void *chan_id)
-{
-	return false;
-}
-#endif
-
-/*
- * DMA Controller - this access the static mappings of the coh901318 dma.
- *
- */
-
-#define COH901318_MOD32_MASK					(0x1F)
-#define COH901318_WORD_MASK					(0xFFFFFFFF)
-/* INT_STATUS - Interrupt Status Registers 32bit (R/-) */
-#define COH901318_INT_STATUS1					(0x0000)
-#define COH901318_INT_STATUS2					(0x0004)
-/* TC_INT_STATUS - Terminal Count Interrupt Status Registers 32bit (R/-) */
-#define COH901318_TC_INT_STATUS1				(0x0008)
-#define COH901318_TC_INT_STATUS2				(0x000C)
-/* TC_INT_CLEAR - Terminal Count Interrupt Clear Registers 32bit (-/W) */
-#define COH901318_TC_INT_CLEAR1					(0x0010)
-#define COH901318_TC_INT_CLEAR2					(0x0014)
-/* RAW_TC_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */
-#define COH901318_RAW_TC_INT_STATUS1				(0x0018)
-#define COH901318_RAW_TC_INT_STATUS2				(0x001C)
-/* BE_INT_STATUS - Bus Error Interrupt Status Registers 32bit (R/-) */
-#define COH901318_BE_INT_STATUS1				(0x0020)
-#define COH901318_BE_INT_STATUS2				(0x0024)
-/* BE_INT_CLEAR - Bus Error Interrupt Clear Registers 32bit (-/W) */
-#define COH901318_BE_INT_CLEAR1					(0x0028)
-#define COH901318_BE_INT_CLEAR2					(0x002C)
-/* RAW_BE_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */
-#define COH901318_RAW_BE_INT_STATUS1				(0x0030)
-#define COH901318_RAW_BE_INT_STATUS2				(0x0034)
-
-/*
- * CX_CFG - Channel Configuration Registers 32bit (R/W)
- */
-#define COH901318_CX_CFG					(0x0100)
-#define COH901318_CX_CFG_SPACING				(0x04)
-/* Channel enable activates tha dma job */
-#define COH901318_CX_CFG_CH_ENABLE				(0x00000001)
-#define COH901318_CX_CFG_CH_DISABLE				(0x00000000)
-/* Request Mode */
-#define COH901318_CX_CFG_RM_MASK				(0x00000006)
-#define COH901318_CX_CFG_RM_MEMORY_TO_MEMORY			(0x0 << 1)
-#define COH901318_CX_CFG_RM_PRIMARY_TO_MEMORY			(0x1 << 1)
-#define COH901318_CX_CFG_RM_MEMORY_TO_PRIMARY			(0x1 << 1)
-#define COH901318_CX_CFG_RM_PRIMARY_TO_SECONDARY		(0x3 << 1)
-#define COH901318_CX_CFG_RM_SECONDARY_TO_PRIMARY		(0x3 << 1)
-/* Linked channel request field. RM must == 11 */
-#define COH901318_CX_CFG_LCRF_SHIFT				3
-#define COH901318_CX_CFG_LCRF_MASK				(0x000001F8)
-#define COH901318_CX_CFG_LCR_DISABLE				(0x00000000)
-/* Terminal Counter Interrupt Request Mask */
-#define COH901318_CX_CFG_TC_IRQ_ENABLE				(0x00000200)
-#define COH901318_CX_CFG_TC_IRQ_DISABLE				(0x00000000)
-/* Bus Error interrupt Mask */
-#define COH901318_CX_CFG_BE_IRQ_ENABLE				(0x00000400)
-#define COH901318_CX_CFG_BE_IRQ_DISABLE				(0x00000000)
-
-/*
- * CX_STAT - Channel Status Registers 32bit (R/-)
- */
-#define COH901318_CX_STAT					(0x0200)
-#define COH901318_CX_STAT_SPACING				(0x04)
-#define COH901318_CX_STAT_RBE_IRQ_IND				(0x00000008)
-#define COH901318_CX_STAT_RTC_IRQ_IND				(0x00000004)
-#define COH901318_CX_STAT_ACTIVE				(0x00000002)
-#define COH901318_CX_STAT_ENABLED				(0x00000001)
-
-/*
- * CX_CTRL - Channel Control Registers 32bit (R/W)
- */
-#define COH901318_CX_CTRL					(0x0400)
-#define COH901318_CX_CTRL_SPACING				(0x10)
-/* Transfer Count Enable */
-#define COH901318_CX_CTRL_TC_ENABLE				(0x00001000)
-#define COH901318_CX_CTRL_TC_DISABLE				(0x00000000)
-/* Transfer Count Value 0 - 4095 */
-#define COH901318_CX_CTRL_TC_VALUE_MASK				(0x00000FFF)
-/* Burst count */
-#define COH901318_CX_CTRL_BURST_COUNT_MASK			(0x0000E000)
-#define COH901318_CX_CTRL_BURST_COUNT_64_BYTES			(0x7 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_48_BYTES			(0x6 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_32_BYTES			(0x5 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_16_BYTES			(0x4 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_8_BYTES			(0x3 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_4_BYTES			(0x2 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_2_BYTES			(0x1 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_1_BYTE			(0x0 << 13)
-/* Source bus size  */
-#define COH901318_CX_CTRL_SRC_BUS_SIZE_MASK			(0x00030000)
-#define COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS			(0x2 << 16)
-#define COH901318_CX_CTRL_SRC_BUS_SIZE_16_BITS			(0x1 << 16)
-#define COH901318_CX_CTRL_SRC_BUS_SIZE_8_BITS			(0x0 << 16)
-/* Source address increment */
-#define COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE			(0x00040000)
-#define COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE			(0x00000000)
-/* Destination Bus Size */
-#define COH901318_CX_CTRL_DST_BUS_SIZE_MASK			(0x00180000)
-#define COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS			(0x2 << 19)
-#define COH901318_CX_CTRL_DST_BUS_SIZE_16_BITS			(0x1 << 19)
-#define COH901318_CX_CTRL_DST_BUS_SIZE_8_BITS			(0x0 << 19)
-/* Destination address increment */
-#define COH901318_CX_CTRL_DST_ADDR_INC_ENABLE			(0x00200000)
-#define COH901318_CX_CTRL_DST_ADDR_INC_DISABLE			(0x00000000)
-/* Master Mode (Master2 is only connected to MSL) */
-#define COH901318_CX_CTRL_MASTER_MODE_MASK			(0x00C00000)
-#define COH901318_CX_CTRL_MASTER_MODE_M2R_M1W			(0x3 << 22)
-#define COH901318_CX_CTRL_MASTER_MODE_M1R_M2W			(0x2 << 22)
-#define COH901318_CX_CTRL_MASTER_MODE_M2RW			(0x1 << 22)
-#define COH901318_CX_CTRL_MASTER_MODE_M1RW			(0x0 << 22)
-/* Terminal Count flag to PER enable */
-#define COH901318_CX_CTRL_TCP_ENABLE				(0x01000000)
-#define COH901318_CX_CTRL_TCP_DISABLE				(0x00000000)
-/* Terminal Count flags to CPU enable */
-#define COH901318_CX_CTRL_TC_IRQ_ENABLE				(0x02000000)
-#define COH901318_CX_CTRL_TC_IRQ_DISABLE			(0x00000000)
-/* Hand shake to peripheral */
-#define COH901318_CX_CTRL_HSP_ENABLE				(0x04000000)
-#define COH901318_CX_CTRL_HSP_DISABLE				(0x00000000)
-#define COH901318_CX_CTRL_HSS_ENABLE				(0x08000000)
-#define COH901318_CX_CTRL_HSS_DISABLE				(0x00000000)
-/* DMA mode */
-#define COH901318_CX_CTRL_DDMA_MASK				(0x30000000)
-#define COH901318_CX_CTRL_DDMA_LEGACY				(0x0 << 28)
-#define COH901318_CX_CTRL_DDMA_DEMAND_DMA1			(0x1 << 28)
-#define COH901318_CX_CTRL_DDMA_DEMAND_DMA2			(0x2 << 28)
-/* Primary Request Data Destination */
-#define COH901318_CX_CTRL_PRDD_MASK				(0x40000000)
-#define COH901318_CX_CTRL_PRDD_DEST				(0x1 << 30)
-#define COH901318_CX_CTRL_PRDD_SOURCE				(0x0 << 30)
-
-/*
- * CX_SRC_ADDR - Channel Source Address Registers 32bit (R/W)
- */
-#define COH901318_CX_SRC_ADDR					(0x0404)
-#define COH901318_CX_SRC_ADDR_SPACING				(0x10)
-
-/*
- * CX_DST_ADDR - Channel Destination Address Registers 32bit R/W
- */
-#define COH901318_CX_DST_ADDR					(0x0408)
-#define COH901318_CX_DST_ADDR_SPACING				(0x10)
-
-/*
- * CX_LNK_ADDR - Channel Link Address Registers 32bit (R/W)
- */
-#define COH901318_CX_LNK_ADDR					(0x040C)
-#define COH901318_CX_LNK_ADDR_SPACING				(0x10)
-#define COH901318_CX_LNK_LINK_IMMEDIATE				(0x00000001)
-#endif /* COH901318_H */

arch/arm/mach-u300/spi.c

@@ -10,9 +10,8 @@
 #include <linux/amba/bus.h>
 #include <linux/spi/spi.h>
 #include <linux/amba/pl022.h>
+#include <linux/platform_data/dma-coh901318.h>
 #include <linux/err.h>
-#include <mach/coh901318.h>
-#include "dma_channels.h"
 
 /*
  * The following is for the actual devices on the SSP/SPI bus

arch/arm/plat-spear/restart.c

@@ -11,8 +11,8 @@
  * warranty of any kind, whether express or implied.
  */
 #include <linux/io.h>
+#include <linux/amba/sp810.h>
 #include <asm/system_misc.h>
-#include <asm/hardware/sp810.h>
 #include <mach/spear.h>
 #include <mach/generic.h>
 

drivers/clk/versatile/clk-vexpress.c

@@ -11,6 +11,7 @@
  * Copyright (C) 2012 ARM Limited
  */
 
+#include <linux/amba/sp810.h>
 #include <linux/clkdev.h>
 #include <linux/clk-provider.h>
 #include <linux/err.h>
@@ -18,8 +19,6 @@
 #include <linux/of_address.h>
 #include <linux/vexpress.h>
 
-#include <asm/hardware/sp810.h>
-
 static struct clk *vexpress_sp810_timerclken[4];
 static DEFINE_SPINLOCK(vexpress_sp810_lock);
 

drivers/clocksource/nomadik-mtu.c

@@ -15,6 +15,7 @@
 #include <linux/clocksource.h>
 #include <linux/clk.h>
 #include <linux/jiffies.h>
+#include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/platform_data/clocksource-nomadik-mtu.h>
 #include <asm/mach/time.h>
@@ -64,6 +65,7 @@ static void __iomem *mtu_base;
 static bool clkevt_periodic;
 static u32 clk_prescale;
 static u32 nmdk_cycle;		/* write-once */
+static struct delay_timer mtu_delay_timer;
 
 #ifdef CONFIG_NOMADIK_MTU_SCHED_CLOCK
 /*
@@ -80,6 +82,11 @@ static u32 notrace nomadik_read_sched_clock(void)
 }
 #endif
 
+static unsigned long nmdk_timer_read_current_timer(void)
+{
+	return ~readl_relaxed(mtu_base + MTU_VAL(0));
+}
+
 /* Clockevent device: use one-shot mode */
 static int nmdk_clkevt_next(unsigned long evt, struct clock_event_device *ev)
 {
@@ -234,4 +241,8 @@ void __init nmdk_timer_init(void __iomem *base, int irq)
 	setup_irq(irq, &nmdk_timer_irq);
 	nmdk_clkevt.cpumask = cpumask_of(0);
 	clockevents_config_and_register(&nmdk_clkevt, rate, 2, 0xffffffffU);
+
+	mtu_delay_timer.read_current_timer = &nmdk_timer_read_current_timer;
+	mtu_delay_timer.freq = rate;
+	register_current_timer_delay(&mtu_delay_timer);
 }

drivers/cpufreq/Makefile

@@ -44,7 +44,7 @@ obj-$(CONFIG_X86_INTEL_PSTATE)		+= intel_pstate.o
 
 ##################################################################################
 # ARM SoC drivers
-obj-$(CONFIG_UX500_SOC_DB8500)		+= db8500-cpufreq.o
+obj-$(CONFIG_UX500_SOC_DB8500)		+= dbx500-cpufreq.o
 obj-$(CONFIG_ARM_S3C2416_CPUFREQ)	+= s3c2416-cpufreq.o
 obj-$(CONFIG_ARM_S3C64XX_CPUFREQ)	+= s3c64xx-cpufreq.o
 obj-$(CONFIG_ARM_S5PV210_CPUFREQ)	+= s5pv210-cpufreq.o

drivers/cpufreq/db8500-cpufreq.c → drivers/cpufreq/dbx500-cpufreq.c

@@ -1,13 +1,13 @@
 /*
  * Copyright (C) STMicroelectronics 2009
- * Copyright (C) ST-Ericsson SA 2010
+ * Copyright (C) ST-Ericsson SA 2010-2012
  *
  * License Terms: GNU General Public License v2
  * Author: Sundar Iyer <sundar.iyer@stericsson.com>
  * Author: Martin Persson <martin.persson@stericsson.com>
  * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- *
  */
+
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/cpufreq.h>
@@ -19,22 +19,23 @@
 static struct cpufreq_frequency_table *freq_table;
 static struct clk *armss_clk;
 
-static struct freq_attr *db8500_cpufreq_attr[] = {
+static struct freq_attr *dbx500_cpufreq_attr[] = {
 	&cpufreq_freq_attr_scaling_available_freqs,
 	NULL,
 };
 
-static int db8500_cpufreq_verify_speed(struct cpufreq_policy *policy)
+static int dbx500_cpufreq_verify_speed(struct cpufreq_policy *policy)
 {
 	return cpufreq_frequency_table_verify(policy, freq_table);
 }
 
-static int db8500_cpufreq_target(struct cpufreq_policy *policy,
+static int dbx500_cpufreq_target(struct cpufreq_policy *policy,
 				unsigned int target_freq,
 				unsigned int relation)
 {
 	struct cpufreq_freqs freqs;
 	unsigned int idx;
+	int ret;
 
 	/* scale the target frequency to one of the extremes supported */
 	if (target_freq < policy->cpuinfo.min_freq)
@@ -43,10 +44,9 @@ static int db8500_cpufreq_target(struct cpufreq_policy *policy,
 		target_freq = policy->cpuinfo.max_freq;
 
 	/* Lookup the next frequency */
-	if (cpufreq_frequency_table_target
-	    (policy, freq_table, target_freq, relation, &idx)) {
+	if (cpufreq_frequency_table_target(policy, freq_table, target_freq,
+					relation, &idx))
 		return -EINVAL;
-	}
 
 	freqs.old = policy->cur;
 	freqs.new = freq_table[idx].frequency;
@@ -59,9 +59,12 @@ static int db8500_cpufreq_target(struct cpufreq_policy *policy,
 		cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
 
 	/* update armss clk frequency */
-	if (clk_set_rate(armss_clk, freq_table[idx].frequency * 1000)) {
-		pr_err("db8500-cpufreq: Failed to update armss clk\n");
-		return -EINVAL;
+	ret = clk_set_rate(armss_clk, freqs.new * 1000);
+
+	if (ret) {
+		pr_err("dbx500-cpufreq: Failed to set armss_clk to %d Hz: error %d\n",
+		       freqs.new * 1000, ret);
+		return ret;
 	}
 
 	/* post change notification */
@@ -71,7 +74,7 @@ static int db8500_cpufreq_target(struct cpufreq_policy *policy,
 	return 0;
 }
 
-static unsigned int db8500_cpufreq_getspeed(unsigned int cpu)
+static unsigned int dbx500_cpufreq_getspeed(unsigned int cpu)
 {
 	int i = 0;
 	unsigned long freq = clk_get_rate(armss_clk) / 1000;
@@ -83,40 +86,26 @@ static unsigned int db8500_cpufreq_getspeed(unsigned int cpu)
 	}
 
 	/* We could not find a corresponding frequency. */
-	pr_err("db8500-cpufreq: Failed to find cpufreq speed\n");
+	pr_err("dbx500-cpufreq: Failed to find cpufreq speed\n");
 	return 0;
 }
 
-static int __cpuinit db8500_cpufreq_init(struct cpufreq_policy *policy)
+static int __cpuinit dbx500_cpufreq_init(struct cpufreq_policy *policy)
 {
-	int i = 0;
 	int res;
 
-	armss_clk = clk_get(NULL, "armss");
-	if (IS_ERR(armss_clk)) {
-		pr_err("db8500-cpufreq : Failed to get armss clk\n");
-		return PTR_ERR(armss_clk);
-	}
-
-	pr_info("db8500-cpufreq : Available frequencies:\n");
-	while (freq_table[i].frequency != CPUFREQ_TABLE_END) {
-		pr_info("  %d Mhz\n", freq_table[i].frequency/1000);
-		i++;
-	}
-
 	/* get policy fields based on the table */
 	res = cpufreq_frequency_table_cpuinfo(policy, freq_table);
 	if (!res)
 		cpufreq_frequency_table_get_attr(freq_table, policy->cpu);
 	else {
-		pr_err("db8500-cpufreq : Failed to read policy table\n");
-		clk_put(armss_clk);
+		pr_err("dbx500-cpufreq: Failed to read policy table\n");
 		return res;
 	}
 
 	policy->min = policy->cpuinfo.min_freq;
 	policy->max = policy->cpuinfo.max_freq;
-	policy->cur = db8500_cpufreq_getspeed(policy->cpu);
+	policy->cur = dbx500_cpufreq_getspeed(policy->cpu);
 	policy->governor = CPUFREQ_DEFAULT_GOVERNOR;
 
 	/*
@@ -132,42 +121,54 @@ static int __cpuinit db8500_cpufreq_init(struct cpufreq_policy *policy)
 	return 0;
 }
 
-static struct cpufreq_driver db8500_cpufreq_driver = {
-	.flags  = CPUFREQ_STICKY,
-	.verify = db8500_cpufreq_verify_speed,
-	.target = db8500_cpufreq_target,
-	.get    = db8500_cpufreq_getspeed,
-	.init   = db8500_cpufreq_init,
-	.name   = "DB8500",
-	.attr   = db8500_cpufreq_attr,
+static struct cpufreq_driver dbx500_cpufreq_driver = {
+	.flags  = CPUFREQ_STICKY | CPUFREQ_CONST_LOOPS,
+	.verify = dbx500_cpufreq_verify_speed,
+	.target = dbx500_cpufreq_target,
+	.get    = dbx500_cpufreq_getspeed,
+	.init   = dbx500_cpufreq_init,
+	.name   = "DBX500",
+	.attr   = dbx500_cpufreq_attr,
 };
 
-static int db8500_cpufreq_probe(struct platform_device *pdev)
+static int dbx500_cpufreq_probe(struct platform_device *pdev)
 {
-	freq_table = dev_get_platdata(&pdev->dev);
+	int i = 0;
 
+	freq_table = dev_get_platdata(&pdev->dev);
 	if (!freq_table) {
-		pr_err("db8500-cpufreq: Failed to fetch cpufreq table\n");
+		pr_err("dbx500-cpufreq: Failed to fetch cpufreq table\n");
 		return -ENODEV;
 	}
 
-	return cpufreq_register_driver(&db8500_cpufreq_driver);
+	armss_clk = clk_get(&pdev->dev, "armss");
+	if (IS_ERR(armss_clk)) {
+		pr_err("dbx500-cpufreq: Failed to get armss clk\n");
+		return PTR_ERR(armss_clk);
+	}
+
+	pr_info("dbx500-cpufreq: Available frequencies:\n");
+	while (freq_table[i].frequency != CPUFREQ_TABLE_END) {
+		pr_info("  %d Mhz\n", freq_table[i].frequency/1000);
+		i++;
+	}
+
+	return cpufreq_register_driver(&dbx500_cpufreq_driver);
 }
 
-static struct platform_driver db8500_cpufreq_plat_driver = {
+static struct platform_driver dbx500_cpufreq_plat_driver = {
 	.driver = {
-		.name = "cpufreq-u8500",
+		.name = "cpufreq-ux500",
 		.owner = THIS_MODULE,
 	},
-	.probe = db8500_cpufreq_probe,
+	.probe = dbx500_cpufreq_probe,
 };
 
-static int __init db8500_cpufreq_register(void)
+static int __init dbx500_cpufreq_register(void)
 {
-	pr_info("cpufreq for DB8500 started\n");
-	return platform_driver_register(&db8500_cpufreq_plat_driver);
+	return platform_driver_register(&dbx500_cpufreq_plat_driver);
 }
-device_initcall(db8500_cpufreq_register);
+device_initcall(dbx500_cpufreq_register);
 
 MODULE_LICENSE("GPL v2");
-MODULE_DESCRIPTION("cpufreq driver for DB8500");
+MODULE_DESCRIPTION("cpufreq driver for DBX500");

drivers/dma/coh901318.c

@@ -21,11 +21,1241 @@
 #include <linux/io.h>
 #include <linux/uaccess.h>
 #include <linux/debugfs.h>
-#include <mach/coh901318.h>
+#include <linux/platform_data/dma-coh901318.h>
 
-#include "coh901318_lli.h"
+#include "coh901318.h"
 #include "dmaengine.h"
 
+#define COH901318_MOD32_MASK					(0x1F)
+#define COH901318_WORD_MASK					(0xFFFFFFFF)
+/* INT_STATUS - Interrupt Status Registers 32bit (R/-) */
+#define COH901318_INT_STATUS1					(0x0000)
+#define COH901318_INT_STATUS2					(0x0004)
+/* TC_INT_STATUS - Terminal Count Interrupt Status Registers 32bit (R/-) */
+#define COH901318_TC_INT_STATUS1				(0x0008)
+#define COH901318_TC_INT_STATUS2				(0x000C)
+/* TC_INT_CLEAR - Terminal Count Interrupt Clear Registers 32bit (-/W) */
+#define COH901318_TC_INT_CLEAR1					(0x0010)
+#define COH901318_TC_INT_CLEAR2					(0x0014)
+/* RAW_TC_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */
+#define COH901318_RAW_TC_INT_STATUS1				(0x0018)
+#define COH901318_RAW_TC_INT_STATUS2				(0x001C)
+/* BE_INT_STATUS - Bus Error Interrupt Status Registers 32bit (R/-) */
+#define COH901318_BE_INT_STATUS1				(0x0020)
+#define COH901318_BE_INT_STATUS2				(0x0024)
+/* BE_INT_CLEAR - Bus Error Interrupt Clear Registers 32bit (-/W) */
+#define COH901318_BE_INT_CLEAR1					(0x0028)
+#define COH901318_BE_INT_CLEAR2					(0x002C)
+/* RAW_BE_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */
+#define COH901318_RAW_BE_INT_STATUS1				(0x0030)
+#define COH901318_RAW_BE_INT_STATUS2				(0x0034)
+
+/*
+ * CX_CFG - Channel Configuration Registers 32bit (R/W)
+ */
+#define COH901318_CX_CFG					(0x0100)
+#define COH901318_CX_CFG_SPACING				(0x04)
+/* Channel enable activates tha dma job */
+#define COH901318_CX_CFG_CH_ENABLE				(0x00000001)
+#define COH901318_CX_CFG_CH_DISABLE				(0x00000000)
+/* Request Mode */
+#define COH901318_CX_CFG_RM_MASK				(0x00000006)
+#define COH901318_CX_CFG_RM_MEMORY_TO_MEMORY			(0x0 << 1)
+#define COH901318_CX_CFG_RM_PRIMARY_TO_MEMORY			(0x1 << 1)
+#define COH901318_CX_CFG_RM_MEMORY_TO_PRIMARY			(0x1 << 1)
+#define COH901318_CX_CFG_RM_PRIMARY_TO_SECONDARY		(0x3 << 1)
+#define COH901318_CX_CFG_RM_SECONDARY_TO_PRIMARY		(0x3 << 1)
+/* Linked channel request field. RM must == 11 */
+#define COH901318_CX_CFG_LCRF_SHIFT				3
+#define COH901318_CX_CFG_LCRF_MASK				(0x000001F8)
+#define COH901318_CX_CFG_LCR_DISABLE				(0x00000000)
+/* Terminal Counter Interrupt Request Mask */
+#define COH901318_CX_CFG_TC_IRQ_ENABLE				(0x00000200)
+#define COH901318_CX_CFG_TC_IRQ_DISABLE				(0x00000000)
+/* Bus Error interrupt Mask */
+#define COH901318_CX_CFG_BE_IRQ_ENABLE				(0x00000400)
+#define COH901318_CX_CFG_BE_IRQ_DISABLE				(0x00000000)
+
+/*
+ * CX_STAT - Channel Status Registers 32bit (R/-)
+ */
+#define COH901318_CX_STAT					(0x0200)
+#define COH901318_CX_STAT_SPACING				(0x04)
+#define COH901318_CX_STAT_RBE_IRQ_IND				(0x00000008)
+#define COH901318_CX_STAT_RTC_IRQ_IND				(0x00000004)
+#define COH901318_CX_STAT_ACTIVE				(0x00000002)
+#define COH901318_CX_STAT_ENABLED				(0x00000001)
+
+/*
+ * CX_CTRL - Channel Control Registers 32bit (R/W)
+ */
+#define COH901318_CX_CTRL					(0x0400)
+#define COH901318_CX_CTRL_SPACING				(0x10)
+/* Transfer Count Enable */
+#define COH901318_CX_CTRL_TC_ENABLE				(0x00001000)
+#define COH901318_CX_CTRL_TC_DISABLE				(0x00000000)
+/* Transfer Count Value 0 - 4095 */
+#define COH901318_CX_CTRL_TC_VALUE_MASK				(0x00000FFF)
+/* Burst count */
+#define COH901318_CX_CTRL_BURST_COUNT_MASK			(0x0000E000)
+#define COH901318_CX_CTRL_BURST_COUNT_64_BYTES			(0x7 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_48_BYTES			(0x6 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_32_BYTES			(0x5 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_16_BYTES			(0x4 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_8_BYTES			(0x3 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_4_BYTES			(0x2 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_2_BYTES			(0x1 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_1_BYTE			(0x0 << 13)
+/* Source bus size  */
+#define COH901318_CX_CTRL_SRC_BUS_SIZE_MASK			(0x00030000)
+#define COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS			(0x2 << 16)
+#define COH901318_CX_CTRL_SRC_BUS_SIZE_16_BITS			(0x1 << 16)
+#define COH901318_CX_CTRL_SRC_BUS_SIZE_8_BITS			(0x0 << 16)
+/* Source address increment */
+#define COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE			(0x00040000)
+#define COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE			(0x00000000)
+/* Destination Bus Size */
+#define COH901318_CX_CTRL_DST_BUS_SIZE_MASK			(0x00180000)
+#define COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS			(0x2 << 19)
+#define COH901318_CX_CTRL_DST_BUS_SIZE_16_BITS			(0x1 << 19)
+#define COH901318_CX_CTRL_DST_BUS_SIZE_8_BITS			(0x0 << 19)
+/* Destination address increment */
+#define COH901318_CX_CTRL_DST_ADDR_INC_ENABLE			(0x00200000)
+#define COH901318_CX_CTRL_DST_ADDR_INC_DISABLE			(0x00000000)
+/* Master Mode (Master2 is only connected to MSL) */
+#define COH901318_CX_CTRL_MASTER_MODE_MASK			(0x00C00000)
+#define COH901318_CX_CTRL_MASTER_MODE_M2R_M1W			(0x3 << 22)
+#define COH901318_CX_CTRL_MASTER_MODE_M1R_M2W			(0x2 << 22)
+#define COH901318_CX_CTRL_MASTER_MODE_M2RW			(0x1 << 22)
+#define COH901318_CX_CTRL_MASTER_MODE_M1RW			(0x0 << 22)
+/* Terminal Count flag to PER enable */
+#define COH901318_CX_CTRL_TCP_ENABLE				(0x01000000)
+#define COH901318_CX_CTRL_TCP_DISABLE				(0x00000000)
+/* Terminal Count flags to CPU enable */
+#define COH901318_CX_CTRL_TC_IRQ_ENABLE				(0x02000000)
+#define COH901318_CX_CTRL_TC_IRQ_DISABLE			(0x00000000)
+/* Hand shake to peripheral */
+#define COH901318_CX_CTRL_HSP_ENABLE				(0x04000000)
+#define COH901318_CX_CTRL_HSP_DISABLE				(0x00000000)
+#define COH901318_CX_CTRL_HSS_ENABLE				(0x08000000)
+#define COH901318_CX_CTRL_HSS_DISABLE				(0x00000000)
+/* DMA mode */
+#define COH901318_CX_CTRL_DDMA_MASK				(0x30000000)
+#define COH901318_CX_CTRL_DDMA_LEGACY				(0x0 << 28)
+#define COH901318_CX_CTRL_DDMA_DEMAND_DMA1			(0x1 << 28)
+#define COH901318_CX_CTRL_DDMA_DEMAND_DMA2			(0x2 << 28)
+/* Primary Request Data Destination */
+#define COH901318_CX_CTRL_PRDD_MASK				(0x40000000)
+#define COH901318_CX_CTRL_PRDD_DEST				(0x1 << 30)
+#define COH901318_CX_CTRL_PRDD_SOURCE				(0x0 << 30)
+
+/*
+ * CX_SRC_ADDR - Channel Source Address Registers 32bit (R/W)
+ */
+#define COH901318_CX_SRC_ADDR					(0x0404)
+#define COH901318_CX_SRC_ADDR_SPACING				(0x10)
+
+/*
+ * CX_DST_ADDR - Channel Destination Address Registers 32bit R/W
+ */
+#define COH901318_CX_DST_ADDR					(0x0408)
+#define COH901318_CX_DST_ADDR_SPACING				(0x10)
+
+/*
+ * CX_LNK_ADDR - Channel Link Address Registers 32bit (R/W)
+ */
+#define COH901318_CX_LNK_ADDR					(0x040C)
+#define COH901318_CX_LNK_ADDR_SPACING				(0x10)
+#define COH901318_CX_LNK_LINK_IMMEDIATE				(0x00000001)
+
+/**
+ * struct coh901318_params - parameters for DMAC configuration
+ * @config: DMA config register
+ * @ctrl_lli_last: DMA control register for the last lli in the list
+ * @ctrl_lli: DMA control register for an lli
+ * @ctrl_lli_chained: DMA control register for a chained lli
+ */
+struct coh901318_params {
+	u32 config;
+	u32 ctrl_lli_last;
+	u32 ctrl_lli;
+	u32 ctrl_lli_chained;
+};
+
+/**
+ * struct coh_dma_channel - dma channel base
+ * @name: ascii name of dma channel
+ * @number: channel id number
+ * @desc_nbr_max: number of preallocated descriptors
+ * @priority_high: prio of channel, 0 low otherwise high.
+ * @param: configuration parameters
+ */
+struct coh_dma_channel {
+	const char name[32];
+	const int number;
+	const int desc_nbr_max;
+	const int priority_high;
+	const struct coh901318_params param;
+};
+
+/**
+ * struct powersave - DMA power save structure
+ * @lock: lock protecting data in this struct
+ * @started_channels: bit mask indicating active dma channels
+ */
+struct powersave {
+	spinlock_t lock;
+	u64 started_channels;
+};
+
+/* points out all dma slave channels.
+ * Syntax is [A1, B1, A2, B2, .... ,-1,-1]
+ * Select all channels from A to B, end of list is marked with -1,-1
+ */
+static int dma_slave_channels[] = {
+	U300_DMA_MSL_TX_0, U300_DMA_SPI_RX,
+	U300_DMA_UART1_TX, U300_DMA_UART1_RX, -1, -1};
+
+/* points out all dma memcpy channels. */
+static int dma_memcpy_channels[] = {
+	U300_DMA_GENERAL_PURPOSE_0, U300_DMA_GENERAL_PURPOSE_8, -1, -1};
+
+#define flags_memcpy_config (COH901318_CX_CFG_CH_DISABLE | \
+			COH901318_CX_CFG_RM_MEMORY_TO_MEMORY | \
+			COH901318_CX_CFG_LCR_DISABLE | \
+			COH901318_CX_CFG_TC_IRQ_ENABLE | \
+			COH901318_CX_CFG_BE_IRQ_ENABLE)
+#define flags_memcpy_lli_chained (COH901318_CX_CTRL_TC_ENABLE | \
+			COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
+			COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
+			COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
+			COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
+			COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
+			COH901318_CX_CTRL_MASTER_MODE_M1RW | \
+			COH901318_CX_CTRL_TCP_DISABLE | \
+			COH901318_CX_CTRL_TC_IRQ_DISABLE | \
+			COH901318_CX_CTRL_HSP_DISABLE | \
+			COH901318_CX_CTRL_HSS_DISABLE | \
+			COH901318_CX_CTRL_DDMA_LEGACY | \
+			COH901318_CX_CTRL_PRDD_SOURCE)
+#define flags_memcpy_lli (COH901318_CX_CTRL_TC_ENABLE | \
+			COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
+			COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
+			COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
+			COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
+			COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
+			COH901318_CX_CTRL_MASTER_MODE_M1RW | \
+			COH901318_CX_CTRL_TCP_DISABLE | \
+			COH901318_CX_CTRL_TC_IRQ_DISABLE | \
+			COH901318_CX_CTRL_HSP_DISABLE | \
+			COH901318_CX_CTRL_HSS_DISABLE | \
+			COH901318_CX_CTRL_DDMA_LEGACY | \
+			COH901318_CX_CTRL_PRDD_SOURCE)
+#define flags_memcpy_lli_last (COH901318_CX_CTRL_TC_ENABLE | \
+			COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
+			COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
+			COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
+			COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
+			COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
+			COH901318_CX_CTRL_MASTER_MODE_M1RW | \
+			COH901318_CX_CTRL_TCP_DISABLE | \
+			COH901318_CX_CTRL_TC_IRQ_ENABLE | \
+			COH901318_CX_CTRL_HSP_DISABLE | \
+			COH901318_CX_CTRL_HSS_DISABLE | \
+			COH901318_CX_CTRL_DDMA_LEGACY | \
+			COH901318_CX_CTRL_PRDD_SOURCE)
+
+const struct coh_dma_channel chan_config[U300_DMA_CHANNELS] = {
+	{
+		.number = U300_DMA_MSL_TX_0,
+		.name = "MSL TX 0",
+		.priority_high = 0,
+	},
+	{
+		.number = U300_DMA_MSL_TX_1,
+		.name = "MSL TX 1",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+	},
+	{
+		.number = U300_DMA_MSL_TX_2,
+		.name = "MSL TX 2",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.desc_nbr_max = 10,
+	},
+	{
+		.number = U300_DMA_MSL_TX_3,
+		.name = "MSL TX 3",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+	},
+	{
+		.number = U300_DMA_MSL_TX_4,
+		.name = "MSL TX 4",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+	},
+	{
+		.number = U300_DMA_MSL_TX_5,
+		.name = "MSL TX 5",
+		.priority_high = 0,
+	},
+	{
+		.number = U300_DMA_MSL_TX_6,
+		.name = "MSL TX 6",
+		.priority_high = 0,
+	},
+	{
+		.number = U300_DMA_MSL_RX_0,
+		.name = "MSL RX 0",
+		.priority_high = 0,
+	},
+	{
+		.number = U300_DMA_MSL_RX_1,
+		.name = "MSL RX 1",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli = 0,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+	},
+	{
+		.number = U300_DMA_MSL_RX_2,
+		.name = "MSL RX 2",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+	},
+	{
+		.number = U300_DMA_MSL_RX_3,
+		.name = "MSL RX 3",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+	},
+	{
+		.number = U300_DMA_MSL_RX_4,
+		.name = "MSL RX 4",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+	},
+	{
+		.number = U300_DMA_MSL_RX_5,
+		.name = "MSL RX 5",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+				COH901318_CX_CTRL_PRDD_DEST,
+	},
+	{
+		.number = U300_DMA_MSL_RX_6,
+		.name = "MSL RX 6",
+		.priority_high = 0,
+	},
+	/*
+	 * Don't set up device address, burst count or size of src
+	 * or dst bus for this peripheral - handled by PrimeCell
+	 * DMA extension.
+	 */
+	{
+		.number = U300_DMA_MMCSD_RX_TX,
+		.name = "MMCSD RX TX",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+
+	},
+	{
+		.number = U300_DMA_MSPRO_TX,
+		.name = "MSPRO TX",
+		.priority_high = 0,
+	},
+	{
+		.number = U300_DMA_MSPRO_RX,
+		.name = "MSPRO RX",
+		.priority_high = 0,
+	},
+	/*
+	 * Don't set up device address, burst count or size of src
+	 * or dst bus for this peripheral - handled by PrimeCell
+	 * DMA extension.
+	 */
+	{
+		.number = U300_DMA_UART0_TX,
+		.name = "UART0 TX",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+	},
+	{
+		.number = U300_DMA_UART0_RX,
+		.name = "UART0 RX",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+	},
+	{
+		.number = U300_DMA_APEX_TX,
+		.name = "APEX TX",
+		.priority_high = 0,
+	},
+	{
+		.number = U300_DMA_APEX_RX,
+		.name = "APEX RX",
+		.priority_high = 0,
+	},
+	{
+		.number = U300_DMA_PCM_I2S0_TX,
+		.name = "PCM I2S0 TX",
+		.priority_high = 1,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+	},
+	{
+		.number = U300_DMA_PCM_I2S0_RX,
+		.name = "PCM I2S0 RX",
+		.priority_high = 1,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_DEST,
+	},
+	{
+		.number = U300_DMA_PCM_I2S1_TX,
+		.name = "PCM I2S1 TX",
+		.priority_high = 1,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_SOURCE,
+	},
+	{
+		.number = U300_DMA_PCM_I2S1_RX,
+		.name = "PCM I2S1 RX",
+		.priority_high = 1,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_DEST,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+				COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+				COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+				COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_ENABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY |
+				COH901318_CX_CTRL_PRDD_DEST,
+	},
+	{
+		.number = U300_DMA_XGAM_CDI,
+		.name = "XGAM CDI",
+		.priority_high = 0,
+	},
+	{
+		.number = U300_DMA_XGAM_PDI,
+		.name = "XGAM PDI",
+		.priority_high = 0,
+	},
+	/*
+	 * Don't set up device address, burst count or size of src
+	 * or dst bus for this peripheral - handled by PrimeCell
+	 * DMA extension.
+	 */
+	{
+		.number = U300_DMA_SPI_TX,
+		.name = "SPI TX",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+	},
+	{
+		.number = U300_DMA_SPI_RX,
+		.name = "SPI RX",
+		.priority_high = 0,
+		.param.config = COH901318_CX_CFG_CH_DISABLE |
+				COH901318_CX_CFG_LCR_DISABLE |
+				COH901318_CX_CFG_TC_IRQ_ENABLE |
+				COH901318_CX_CFG_BE_IRQ_ENABLE,
+		.param.ctrl_lli_chained = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_DISABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+		.param.ctrl_lli_last = 0 |
+				COH901318_CX_CTRL_TC_ENABLE |
+				COH901318_CX_CTRL_MASTER_MODE_M1RW |
+				COH901318_CX_CTRL_TCP_DISABLE |
+				COH901318_CX_CTRL_TC_IRQ_ENABLE |
+				COH901318_CX_CTRL_HSP_ENABLE |
+				COH901318_CX_CTRL_HSS_DISABLE |
+				COH901318_CX_CTRL_DDMA_LEGACY,
+
+	},
+	{
+		.number = U300_DMA_GENERAL_PURPOSE_0,
+		.name = "GENERAL 00",
+		.priority_high = 0,
+
+		.param.config = flags_memcpy_config,
+		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
+		.param.ctrl_lli = flags_memcpy_lli,
+		.param.ctrl_lli_last = flags_memcpy_lli_last,
+	},
+	{
+		.number = U300_DMA_GENERAL_PURPOSE_1,
+		.name = "GENERAL 01",
+		.priority_high = 0,
+
+		.param.config = flags_memcpy_config,
+		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
+		.param.ctrl_lli = flags_memcpy_lli,
+		.param.ctrl_lli_last = flags_memcpy_lli_last,
+	},
+	{
+		.number = U300_DMA_GENERAL_PURPOSE_2,
+		.name = "GENERAL 02",
+		.priority_high = 0,
+
+		.param.config = flags_memcpy_config,
+		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
+		.param.ctrl_lli = flags_memcpy_lli,
+		.param.ctrl_lli_last = flags_memcpy_lli_last,
+	},
+	{
+		.number = U300_DMA_GENERAL_PURPOSE_3,
+		.name = "GENERAL 03",
+		.priority_high = 0,
+
+		.param.config = flags_memcpy_config,
+		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
+		.param.ctrl_lli = flags_memcpy_lli,
+		.param.ctrl_lli_last = flags_memcpy_lli_last,
+	},
+	{
+		.number = U300_DMA_GENERAL_PURPOSE_4,
+		.name = "GENERAL 04",
+		.priority_high = 0,
+
+		.param.config = flags_memcpy_config,
+		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
+		.param.ctrl_lli = flags_memcpy_lli,
+		.param.ctrl_lli_last = flags_memcpy_lli_last,
+	},
+	{
+		.number = U300_DMA_GENERAL_PURPOSE_5,
+		.name = "GENERAL 05",
+		.priority_high = 0,
+
+		.param.config = flags_memcpy_config,
+		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
+		.param.ctrl_lli = flags_memcpy_lli,
+		.param.ctrl_lli_last = flags_memcpy_lli_last,
+	},
+	{
+		.number = U300_DMA_GENERAL_PURPOSE_6,
+		.name = "GENERAL 06",
+		.priority_high = 0,
+
+		.param.config = flags_memcpy_config,
+		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
+		.param.ctrl_lli = flags_memcpy_lli,
+		.param.ctrl_lli_last = flags_memcpy_lli_last,
+	},
+	{
+		.number = U300_DMA_GENERAL_PURPOSE_7,
+		.name = "GENERAL 07",
+		.priority_high = 0,
+
+		.param.config = flags_memcpy_config,
+		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
+		.param.ctrl_lli = flags_memcpy_lli,
+		.param.ctrl_lli_last = flags_memcpy_lli_last,
+	},
+	{
+		.number = U300_DMA_GENERAL_PURPOSE_8,
+		.name = "GENERAL 08",
+		.priority_high = 0,
+
+		.param.config = flags_memcpy_config,
+		.param.ctrl_lli_chained = flags_memcpy_lli_chained,
+		.param.ctrl_lli = flags_memcpy_lli,
+		.param.ctrl_lli_last = flags_memcpy_lli_last,
+	},
+	{
+		.number = U300_DMA_UART1_TX,
+		.name = "UART1 TX",
+		.priority_high = 0,
+	},
+	{
+		.number = U300_DMA_UART1_RX,
+		.name = "UART1 RX",
+		.priority_high = 0,
+	}
+};
+
 #define COHC_2_DEV(cohc) (&cohc->chan.dev->device)
 
 #ifdef VERBOSE_DEBUG
@@ -54,7 +1284,6 @@ struct coh901318_base {
 	struct dma_device dma_slave;
 	struct dma_device dma_memcpy;
 	struct coh901318_chan *chans;
-	struct coh901318_platform *platform;
 };
 
 struct coh901318_chan {
@@ -75,8 +1304,8 @@ struct coh901318_chan {
 	unsigned long nbr_active_done;
 	unsigned long busy;
 
-	u32 runtime_addr;
-	u32 runtime_ctrl;
+	u32 addr;
+	u32 ctrl;
 
 	struct coh901318_base *base;
 };
@@ -122,7 +1351,7 @@ static int coh901318_debugfs_read(struct file *file, char __user *buf,
 
 	tmp += sprintf(tmp, "DMA -- enabled dma channels\n");
 
-	for (i = 0; i < debugfs_dma_base->platform->max_channels; i++)
+	for (i = 0; i < U300_DMA_CHANNELS; i++)
 		if (started_channels & (1 << i))
 			tmp += sprintf(tmp, "channel %d\n", i);
 
@@ -187,25 +1416,16 @@ static inline struct coh901318_chan *to_coh901318_chan(struct dma_chan *chan)
 	return container_of(chan, struct coh901318_chan, chan);
 }
 
-static inline dma_addr_t
-cohc_dev_addr(struct coh901318_chan *cohc)
-{
-	/* Runtime supplied address will take precedence */
-	if (cohc->runtime_addr)
-		return cohc->runtime_addr;
-	return cohc->base->platform->chan_conf[cohc->id].dev_addr;
-}
-
 static inline const struct coh901318_params *
 cohc_chan_param(struct coh901318_chan *cohc)
 {
-	return &cohc->base->platform->chan_conf[cohc->id].param;
+	return &chan_config[cohc->id].param;
 }
 
 static inline const struct coh_dma_channel *
 cohc_chan_conf(struct coh901318_chan *cohc)
 {
-	return &cohc->base->platform->chan_conf[cohc->id];
+	return &chan_config[cohc->id];
 }
 
 static void enable_powersave(struct coh901318_chan *cohc)
@@ -217,12 +1437,6 @@ static void enable_powersave(struct coh901318_chan *cohc)
 
 	pm->started_channels &= ~(1ULL << cohc->id);
 
-	if (!pm->started_channels) {
-		/* DMA no longer intends to access memory */
-		cohc->base->platform->access_memory_state(cohc->base->dev,
-							  false);
-	}
-
 	spin_unlock_irqrestore(&pm->lock, flags);
 }
 static void disable_powersave(struct coh901318_chan *cohc)
@@ -232,12 +1446,6 @@ static void disable_powersave(struct coh901318_chan *cohc)
 
 	spin_lock_irqsave(&pm->lock, flags);
 
-	if (!pm->started_channels) {
-		/* DMA intends to access memory */
-		cohc->base->platform->access_memory_state(cohc->base->dev,
-							  true);
-	}
-
 	pm->started_channels |= (1ULL << cohc->id);
 
 	spin_unlock_irqrestore(&pm->lock, flags);
@@ -596,7 +1804,7 @@ static int coh901318_config(struct coh901318_chan *cohc,
 	if (param)
 		p = param;
 	else
-		p = &cohc->base->platform->chan_conf[channel].param;
+		p = cohc_chan_param(cohc);
 
 	/* Clear any pending BE or TC interrupt */
 	if (channel < 32) {
@@ -1052,9 +2260,9 @@ coh901318_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl,
 	 * sure the bits you set per peripheral channel are
 	 * cleared in the default config from the platform.
 	 */
-	ctrl_chained |= cohc->runtime_ctrl;
-	ctrl_last |= cohc->runtime_ctrl;
-	ctrl |= cohc->runtime_ctrl;
+	ctrl_chained |= cohc->ctrl;
+	ctrl_last |= cohc->ctrl;
+	ctrl |= cohc->ctrl;
 
 	if (direction == DMA_MEM_TO_DEV) {
 		u32 tx_flags = COH901318_CX_CTRL_PRDD_SOURCE |
@@ -1103,7 +2311,7 @@ coh901318_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl,
 
 	/* initiate allocated lli list */
 	ret = coh901318_lli_fill_sg(&cohc->base->pool, lli, sgl, sg_len,
-				    cohc_dev_addr(cohc),
+				    cohc->addr,
 				    ctrl_chained,
 				    ctrl,
 				    ctrl_last,
@@ -1244,7 +2452,7 @@ static void coh901318_dma_set_runtimeconfig(struct dma_chan *chan,
 	dma_addr_t addr;
 	enum dma_slave_buswidth addr_width;
 	u32 maxburst;
-	u32 runtime_ctrl = 0;
+	u32 ctrl = 0;
 	int i = 0;
 
 	/* We only support mem to per or per to mem transfers */
@@ -1265,7 +2473,7 @@ static void coh901318_dma_set_runtimeconfig(struct dma_chan *chan,
 		addr_width);
 	switch (addr_width)  {
 	case DMA_SLAVE_BUSWIDTH_1_BYTE:
-		runtime_ctrl |=
+		ctrl |=
 			COH901318_CX_CTRL_SRC_BUS_SIZE_8_BITS |
 			COH901318_CX_CTRL_DST_BUS_SIZE_8_BITS;
 
@@ -1277,7 +2485,7 @@ static void coh901318_dma_set_runtimeconfig(struct dma_chan *chan,
 
 		break;
 	case DMA_SLAVE_BUSWIDTH_2_BYTES:
-		runtime_ctrl |=
+		ctrl |=
 			COH901318_CX_CTRL_SRC_BUS_SIZE_16_BITS |
 			COH901318_CX_CTRL_DST_BUS_SIZE_16_BITS;
 
@@ -1290,7 +2498,7 @@ static void coh901318_dma_set_runtimeconfig(struct dma_chan *chan,
 		break;
 	case DMA_SLAVE_BUSWIDTH_4_BYTES:
 		/* Direction doesn't matter here, it's 32/32 bits */
-		runtime_ctrl |=
+		ctrl |=
 			COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
 			COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS;
 
@@ -1307,13 +2515,13 @@ static void coh901318_dma_set_runtimeconfig(struct dma_chan *chan,
 		return;
 	}
 
-	runtime_ctrl |= burst_sizes[i].reg;
+	ctrl |= burst_sizes[i].reg;
 	dev_dbg(COHC_2_DEV(cohc),
 		"selected burst size %d bytes for address width %d bytes, maxburst %d\n",
 		burst_sizes[i].burst_8bit, addr_width, maxburst);
 
-	cohc->runtime_addr = addr;
-	cohc->runtime_ctrl = runtime_ctrl;
+	cohc->addr = addr;
+	cohc->ctrl = ctrl;
 }
 
 static int
@@ -1431,7 +2639,6 @@ void coh901318_base_init(struct dma_device *dma, const int *pick_chans,
 static int __init coh901318_probe(struct platform_device *pdev)
 {
 	int err = 0;
-	struct coh901318_platform *pdata;
 	struct coh901318_base *base;
 	int irq;
 	struct resource *io;
@@ -1447,13 +2654,9 @@ static int __init coh901318_probe(struct platform_device *pdev)
 				    pdev->dev.driver->name) == NULL)
 		return -ENOMEM;
 
-	pdata = pdev->dev.platform_data;
-	if (!pdata)
-		return -ENODEV;
-
 	base = devm_kzalloc(&pdev->dev,
 			    ALIGN(sizeof(struct coh901318_base), 4) +
-			    pdata->max_channels *
+			    U300_DMA_CHANNELS *
 			    sizeof(struct coh901318_chan),
 			    GFP_KERNEL);
 	if (!base)
@@ -1466,7 +2669,6 @@ static int __init coh901318_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	base->dev = &pdev->dev;
-	base->platform = pdata;
 	spin_lock_init(&base->pm.lock);
 	base->pm.started_channels = 0;
 
@@ -1488,7 +2690,7 @@ static int __init coh901318_probe(struct platform_device *pdev)
 		return err;
 
 	/* init channels for device transfers */
-	coh901318_base_init(&base->dma_slave,  base->platform->chans_slave,
+	coh901318_base_init(&base->dma_slave, dma_slave_channels,
 			    base);
 
 	dma_cap_zero(base->dma_slave.cap_mask);
@@ -1508,7 +2710,7 @@ static int __init coh901318_probe(struct platform_device *pdev)
 		goto err_register_slave;
 
 	/* init channels for memcpy */
-	coh901318_base_init(&base->dma_memcpy, base->platform->chans_memcpy,
+	coh901318_base_init(&base->dma_memcpy, dma_memcpy_channels,
 			    base);
 
 	dma_cap_zero(base->dma_memcpy.cap_mask);

drivers/dma/coh901318_lli.h → drivers/dma/coh901318.h

@@ -1,16 +1,15 @@
 /*
- * driver/dma/coh901318_lli.h
- *
- * Copyright (C) 2007-2009 ST-Ericsson
+ * Copyright (C) 2007-2013 ST-Ericsson
  * License terms: GNU General Public License (GPL) version 2
- * Support functions for handling lli for coh901318
+ * DMA driver for COH 901 318
  * Author: Per Friden <per.friden@stericsson.com>
  */
 
-#ifndef COH901318_LLI_H
-#define COH901318_LLI_H
+#ifndef COH901318_H
+#define COH901318_H
 
-#include <mach/coh901318.h>
+#define MAX_DMA_PACKET_SIZE_SHIFT 11
+#define MAX_DMA_PACKET_SIZE (1 << MAX_DMA_PACKET_SIZE_SHIFT)
 
 struct device;
 
@@ -24,7 +23,25 @@ struct coh901318_pool {
 #endif
 };
 
-struct device;
+/**
+ * struct coh901318_lli - linked list item for DMAC
+ * @control: control settings for DMAC
+ * @src_addr: transfer source address
+ * @dst_addr: transfer destination address
+ * @link_addr:  physical address to next lli
+ * @virt_link_addr: virtual address of next lli (only used by pool_free)
+ * @phy_this: physical address of current lli (only used by pool_free)
+ */
+struct coh901318_lli {
+	u32 control;
+	dma_addr_t src_addr;
+	dma_addr_t dst_addr;
+	dma_addr_t link_addr;
+
+	void *virt_link_addr;
+	dma_addr_t phy_this;
+};
+
 /**
  * coh901318_pool_create() - Creates an dma pool for lli:s
  * @pool: pool handle
@@ -121,4 +138,4 @@ coh901318_lli_fill_sg(struct coh901318_pool *pool,
 		      u32 ctrl, u32 ctrl_last,
 		      enum dma_transfer_direction dir, u32 ctrl_irq_mask);
 
-#endif /* COH901318_LLI_H */
+#endif /* COH901318_H */

drivers/dma/coh901318_lli.c

@@ -11,9 +11,9 @@
 #include <linux/memory.h>
 #include <linux/gfp.h>
 #include <linux/dmapool.h>
-#include <mach/coh901318.h>
+#include <linux/dmaengine.h>
 
-#include "coh901318_lli.h"
+#include "coh901318.h"
 
 #if (defined(CONFIG_DEBUG_FS) && defined(CONFIG_U300_DEBUG))
 #define DEBUGFS_POOL_COUNTER_RESET(pool) (pool->debugfs_pool_counter = 0)

drivers/mfd/db8500-prcmu.c

@@ -3102,8 +3102,8 @@ static struct mfd_cell db8500_prcmu_devs[] = {
 		.pdata_size = sizeof(db8500_regulators),
 	},
 	{
-		.name = "cpufreq-u8500",
-		.of_compatible = "stericsson,cpufreq-u8500",
+		.name = "cpufreq-ux500",
+		.of_compatible = "stericsson,cpufreq-ux500",
 		.platform_data = &db8500_cpufreq_table,
 		.pdata_size = sizeof(db8500_cpufreq_table),
 	},

drivers/mtd/nand/omap2.c

@@ -1332,6 +1332,7 @@ static int omap_nand_probe(struct platform_device *pdev)
 	dma_cap_mask_t mask;
 	unsigned sig;
 	struct resource			*res;
+	struct mtd_part_parser_data	ppdata = {};
 
 	pdata = pdev->dev.platform_data;
 	if (pdata == NULL) {
@@ -1557,7 +1558,8 @@ static int omap_nand_probe(struct platform_device *pdev)
 		goto out_release_mem_region;
 	}
 
-	mtd_device_parse_register(&info->mtd, NULL, NULL, pdata->parts,
+	ppdata.of_node = pdata->of_node;
+	mtd_device_parse_register(&info->mtd, NULL, &ppdata, pdata->parts,
 				  pdata->nr_parts);
 
 	platform_set_drvdata(pdev, &info->mtd);

drivers/mtd/onenand/omap2.c

@@ -637,6 +637,7 @@ static int omap2_onenand_probe(struct platform_device *pdev)
 	struct onenand_chip *this;
 	int r;
 	struct resource *res;
+	struct mtd_part_parser_data ppdata = {};
 
 	pdata = pdev->dev.platform_data;
 	if (pdata == NULL) {
@@ -767,7 +768,8 @@ static int omap2_onenand_probe(struct platform_device *pdev)
 	if ((r = onenand_scan(&c->mtd, 1)) < 0)
 		goto err_release_regulator;
 
-	r = mtd_device_parse_register(&c->mtd, NULL, NULL,
+	ppdata.of_node = pdata->of_node;
+	r = mtd_device_parse_register(&c->mtd, NULL, &ppdata,
 				      pdata ? pdata->parts : NULL,
 				      pdata ? pdata->nr_parts : 0);
 	if (r)

include/linux/platform_data/dma-coh901318.h

@@ -0,0 +1,72 @@
+/*
+ * Platform data for the COH901318 DMA controller
+ * Copyright (C) 2007-2013 ST-Ericsson
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#ifndef PLAT_COH901318_H
+#define PLAT_COH901318_H
+
+#ifdef CONFIG_COH901318
+
+/* We only support the U300 DMA channels */
+#define U300_DMA_MSL_TX_0		0
+#define U300_DMA_MSL_TX_1		1
+#define U300_DMA_MSL_TX_2		2
+#define U300_DMA_MSL_TX_3		3
+#define U300_DMA_MSL_TX_4		4
+#define U300_DMA_MSL_TX_5		5
+#define U300_DMA_MSL_TX_6		6
+#define U300_DMA_MSL_RX_0		7
+#define U300_DMA_MSL_RX_1		8
+#define U300_DMA_MSL_RX_2		9
+#define U300_DMA_MSL_RX_3		10
+#define U300_DMA_MSL_RX_4		11
+#define U300_DMA_MSL_RX_5		12
+#define U300_DMA_MSL_RX_6		13
+#define U300_DMA_MMCSD_RX_TX		14
+#define U300_DMA_MSPRO_TX		15
+#define U300_DMA_MSPRO_RX		16
+#define U300_DMA_UART0_TX		17
+#define U300_DMA_UART0_RX		18
+#define U300_DMA_APEX_TX		19
+#define U300_DMA_APEX_RX		20
+#define U300_DMA_PCM_I2S0_TX		21
+#define U300_DMA_PCM_I2S0_RX		22
+#define U300_DMA_PCM_I2S1_TX		23
+#define U300_DMA_PCM_I2S1_RX		24
+#define U300_DMA_XGAM_CDI		25
+#define U300_DMA_XGAM_PDI		26
+#define U300_DMA_SPI_TX			27
+#define U300_DMA_SPI_RX			28
+#define U300_DMA_GENERAL_PURPOSE_0	29
+#define U300_DMA_GENERAL_PURPOSE_1	30
+#define U300_DMA_GENERAL_PURPOSE_2	31
+#define U300_DMA_GENERAL_PURPOSE_3	32
+#define U300_DMA_GENERAL_PURPOSE_4	33
+#define U300_DMA_GENERAL_PURPOSE_5	34
+#define U300_DMA_GENERAL_PURPOSE_6	35
+#define U300_DMA_GENERAL_PURPOSE_7	36
+#define U300_DMA_GENERAL_PURPOSE_8	37
+#define U300_DMA_UART1_TX		38
+#define U300_DMA_UART1_RX		39
+
+#define U300_DMA_DEVICE_CHANNELS	32
+#define U300_DMA_CHANNELS		40
+
+/**
+ * coh901318_filter_id() - DMA channel filter function
+ * @chan: dma channel handle
+ * @chan_id: id of dma channel to be filter out
+ *
+ * In dma_request_channel() it specifies what channel id to be requested
+ */
+bool coh901318_filter_id(struct dma_chan *chan, void *chan_id);
+#else
+static inline bool coh901318_filter_id(struct dma_chan *chan, void *chan_id)
+{
+	return false;
+}
+#endif
+
+#endif /* PLAT_COH901318_H */

include/linux/platform_data/mtd-nand-omap2.h

@@ -60,6 +60,8 @@ struct omap_nand_platform_data {
 	int			devsize;
 	enum omap_ecc           ecc_opt;
 	struct gpmc_nand_regs	reg;
-};
 
+	/* for passing the partitions */
+	struct device_node	*of_node;
+};
 #endif

include/linux/platform_data/mtd-onenand-omap2.h

@@ -29,5 +29,8 @@ struct omap_onenand_platform_data {
 	u8			flags;
 	u8			regulator_can_sleep;
 	u8			skip_initial_unlocking;
+
+	/* for passing the partitions */
+	struct device_node	*of_node;
 };
 #endif