Merge branch 'topic/hda' into for-next

Documentation/cgroup-v2.txt

@@ -7,7 +7,7 @@ This is the authoritative documentation on the design, interface and
 conventions of cgroup v2.  It describes all userland-visible aspects
 of cgroup including core and specific controller behaviors.  All
 future changes must be reflected in this document.  Documentation for
-v1 is available under Documentation/cgroup-legacy/.
+v1 is available under Documentation/cgroup-v1/.
 
 CONTENTS
 

Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt

@@ -30,7 +30,7 @@ that they are defined using standard clock bindings with following
 clock-output-names:
  - "xin24m" - crystal input - required,
  - "ext_i2s" - external I2S clock - optional,
- - "ext_gmac" - external GMAC clock - optional
+ - "rmii_clkin" - external EMAC clock - optional
 
 Example: Clock controller node:
 

Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt

@@ -24,9 +24,8 @@ Main node required properties:
 		1 = edge triggered
 		4 = level triggered
 
-  Cells 4 and beyond are reserved for future use. When the 1st cell
-  has a value of 0 or 1, cells 4 and beyond act as padding, and may be
-  ignored. It is recommended that padding cells have a value of 0.
+  Cells 4 and beyond are reserved for future use and must have a value
+  of 0 if present.
 
 - reg : Specifies base physical address(s) and size of the GIC
   registers, in the following order:

Documentation/devicetree/bindings/net/renesas,ravb.txt

@@ -82,8 +82,8 @@ Example:
 				  "ch16", "ch17", "ch18", "ch19",
 				  "ch20", "ch21", "ch22", "ch23",
 				  "ch24";
-		clocks = <&mstp8_clks R8A7795_CLK_ETHERAVB>;
-		power-domains = <&cpg_clocks>;
+		clocks = <&cpg CPG_MOD 812>;
+		power-domains = <&cpg>;
 		phy-mode = "rgmii-id";
 		phy-handle = <&phy0>;
 

Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt

@@ -8,6 +8,7 @@ OHCI and EHCI controllers.
 Required properties:
 - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
 	      "renesas,pci-r8a7791" for the R8A7791 SoC;
+	      "renesas,pci-r8a7793" for the R8A7793 SoC;
 	      "renesas,pci-r8a7794" for the R8A7794 SoC;
 	      "renesas,pci-rcar-gen2" for a generic R-Car Gen2 compatible device
 

Documentation/devicetree/bindings/pci/rcar-pci.txt

@@ -4,6 +4,7 @@ Required properties:
 compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC;
 	    "renesas,pcie-r8a7790" for the R8A7790 SoC;
 	    "renesas,pcie-r8a7791" for the R8A7791 SoC;
+	    "renesas,pcie-r8a7793" for the R8A7793 SoC;
 	    "renesas,pcie-r8a7795" for the R8A7795 SoC;
 	    "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device.
 

Documentation/devicetree/bindings/regulator/tps65217.txt

@@ -26,11 +26,7 @@ Example:
 		ti,pmic-shutdown-controller;
 
 		regulators {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
 			dcdc1_reg: dcdc1 {
-				reg = <0>;
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -38,7 +34,6 @@ Example:
 			};
 
 			dcdc2_reg: dcdc2 {
-				reg = <1>;
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -46,7 +41,6 @@ Example:
 			};
 
 			dcdc3_reg: dcc3 {
-				reg = <2>;
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1500000>;
 				regulator-boot-on;
@@ -54,7 +48,6 @@ Example:
 			};
 
 			ldo1_reg: ldo1 {
-				reg = <3>;
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -62,7 +55,6 @@ Example:
 			};
 
 			ldo2_reg: ldo2 {
-				reg = <4>;
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -70,7 +62,6 @@ Example:
 			};
 
 			ldo3_reg: ldo3 {
-				reg = <5>;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -78,7 +69,6 @@ Example:
 			};
 
 			ldo4_reg: ldo4 {
-				reg = <6>;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;

Documentation/devicetree/bindings/rtc/s3c-rtc.txt

@@ -14,6 +14,10 @@ Required properties:
   interrupt number is the rtc alarm interrupt and second interrupt number
   is the rtc tick interrupt. The number of cells representing a interrupt
   depends on the parent interrupt controller.
+- clocks: Must contain a list of phandle and clock specifier for the rtc
+          and source clocks.
+- clock-names: Must contain "rtc" and "rtc_src" entries sorted in the
+               same order as the clocks property.
 
 Example:
 
@@ -21,4 +25,6 @@ Example:
 		compatible = "samsung,s3c6410-rtc";
 		reg = <0x10070000 0x100>;
 		interrupts = <44 0 45 0>;
+		clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
+		clock-names = "rtc", "rtc_src";
 	};

Documentation/devicetree/bindings/serial/fsl-imx-uart.txt

@@ -9,7 +9,7 @@ Optional properties:
 - fsl,uart-has-rtscts : Indicate the uart has rts and cts
 - fsl,irda-mode : Indicate the uart supports irda mode
 - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
-                  is DCE mode by default.
+                  in DCE mode by default.
 
 Note: Each uart controller should have an alias correctly numbered
 in "aliases" node.

Documentation/devicetree/bindings/thermal/rcar-thermal.txt

@@ -1,8 +1,9 @@
 * Renesas R-Car Thermal
 
 Required properties:
-- compatible		: "renesas,thermal-<soctype>", "renesas,rcar-thermal"
-			  as fallback.
+- compatible		: "renesas,thermal-<soctype>",
+			   "renesas,rcar-gen2-thermal" (with thermal-zone) or
+			   "renesas,rcar-thermal" (without thermal-zone) as fallback.
 			  Examples with soctypes are:
 			    - "renesas,thermal-r8a73a4" (R-Mobile APE6)
 			    - "renesas,thermal-r8a7779" (R-Car H1)
@@ -36,3 +37,35 @@ thermal@e61f0000 {
 		0xe61f0300 0x38>;
 	interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 };
+
+Example (with thermal-zone):
+
+thermal-zones {
+	cpu_thermal: cpu-thermal {
+		polling-delay-passive	= <1000>;
+		polling-delay		= <5000>;
+
+		thermal-sensors = <&thermal>;
+
+		trips {
+			cpu-crit {
+				temperature	= <115000>;
+				hysteresis	= <0>;
+				type		= "critical";
+			};
+		};
+		cooling-maps {
+		};
+	};
+};
+
+thermal: thermal@e61f0000 {
+	compatible =	"renesas,thermal-r8a7790",
+			"renesas,rcar-gen2-thermal",
+			"renesas,rcar-thermal";
+	reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
+	interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&mstp5_clks R8A7790_CLK_THERMAL>;
+	power-domains = <&cpg_clocks>;
+	#thermal-sensor-cells = <0>;
+};

Documentation/filesystems/efivarfs.txt

@@ -14,3 +14,10 @@ filesystem.
 efivarfs is typically mounted like this,
 
 	mount -t efivarfs none /sys/firmware/efi/efivars
+
+Due to the presence of numerous firmware bugs where removing non-standard
+UEFI variables causes the system firmware to fail to POST, efivarfs
+files that are not well-known standardized variables are created
+as immutable files.  This doesn't prevent removal - "chattr -i" will work -
+but it does prevent this kind of failure from being accomplished
+accidentally.

Documentation/kernel-parameters.txt

@@ -4235,6 +4235,17 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			The default value of this parameter is determined by
 			the config option CONFIG_WQ_POWER_EFFICIENT_DEFAULT.
 
+	workqueue.debug_force_rr_cpu
+			Workqueue used to implicitly guarantee that work
+			items queued without explicit CPU specified are put
+			on the local CPU.  This guarantee is no longer true
+			and while local CPU is still preferred work items
+			may be put on foreign CPUs.  This debug option
+			forces round-robin CPU selection to flush out
+			usages which depend on the now broken guarantee.
+			When enabled, memory and cache locality will be
+			impacted.
+
 	x2apic_phys	[X86-64,APIC] Use x2apic physical mode instead of
 			default x2apic cluster mode on platforms
 			supporting x2apic.

Documentation/timers/hpet.txt

@@ -1,9 +1,7 @@
 		High Precision Event Timer Driver for Linux
 
 The High Precision Event Timer (HPET) hardware follows a specification
-by Intel and Microsoft which can be found at
-
-	http://www.intel.com/hardwaredesign/hpetspec_1.pdf
+by Intel and Microsoft, revision 1.
 
 Each HPET has one fixed-rate counter (at 10+ MHz, hence "High Precision")
 and up to 32 comparators.  Normally three or more comparators are provided,

MAINTAINERS

@@ -920,17 +920,24 @@ M:	Emilio López <emilio@elopez.com.ar>
 S:	Maintained
 F:	drivers/clk/sunxi/
 
-ARM/Amlogic MesonX SoC support
+ARM/Amlogic Meson SoC support
 M:	Carlo Caione <carlo@caione.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-meson@googlegroups.com
+W:	http://linux-meson.com/
 S:	Maintained
-F:	drivers/media/rc/meson-ir.c
-N:	meson[x68]
+F:	arch/arm/mach-meson/
+F:	arch/arm/boot/dts/meson*
+N:	meson
 
 ARM/Annapurna Labs ALPINE ARCHITECTURE
 M:	Tsahee Zidenberg <tsahee@annapurnalabs.com>
+M:	Antoine Tenart <antoine.tenart@free-electrons.com>
 S:	Maintained
 F:	arch/arm/mach-alpine/
+F:	arch/arm/boot/dts/alpine*
+F:	arch/arm64/boot/dts/al/
+F:	drivers/*/*alpine*
 
 ARM/ATMEL AT91RM9200, AT91SAM9 AND SAMA5 SOC SUPPORT
 M:	Nicolas Ferre <nicolas.ferre@atmel.com>
@@ -1442,8 +1449,8 @@ S:	Maintained
 ARM/RENESAS ARM64 ARCHITECTURE
 M:	Simon Horman <horms@verge.net.au>
 M:	Magnus Damm <magnus.damm@gmail.com>
-L:	linux-sh@vger.kernel.org
-Q:	http://patchwork.kernel.org/project/linux-sh/list/
+L:	linux-renesas-soc@vger.kernel.org
+Q:	http://patchwork.kernel.org/project/linux-renesas-soc/list/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git next
 S:	Supported
 F:	arch/arm64/boot/dts/renesas/
@@ -2362,14 +2369,6 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi.git
 S:	Maintained
 N:	bcm2835
 
-BROADCOM BCM33XX MIPS ARCHITECTURE
-M:	Kevin Cernekee <cernekee@gmail.com>
-L:	linux-mips@linux-mips.org
-S:	Maintained
-F:	arch/mips/bcm3384/*
-F:	arch/mips/include/asm/mach-bcm3384/*
-F:	arch/mips/kernel/*bmips*
-
 BROADCOM BCM47XX MIPS ARCHITECTURE
 M:	Hauke Mehrtens <hauke@hauke-m.de>
 M:	Rafał Miłecki <zajec5@gmail.com>
@@ -3452,7 +3451,6 @@ F:	drivers/usb/dwc2/
 DESIGNWARE USB3 DRD IP DRIVER
 M:	Felipe Balbi <balbi@kernel.org>
 L:	linux-usb@vger.kernel.org
-L:	linux-omap@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git
 S:	Maintained
 F:	drivers/usb/dwc3/
@@ -6136,7 +6134,7 @@ F:	include/uapi/linux/sunrpc/
 
 KERNEL SELFTEST FRAMEWORK
 M:	Shuah Khan <shuahkh@osg.samsung.com>
-L:	linux-api@vger.kernel.org
+L:	linux-kselftest@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/shuah/linux-kselftest
 S:	Maintained
 F:	tools/testing/selftests
@@ -7362,7 +7360,7 @@ F:	drivers/tty/isicom.c
 F:	include/linux/isicom.h
 
 MUSB MULTIPOINT HIGH SPEED DUAL-ROLE CONTROLLER
-M:	Felipe Balbi <balbi@kernel.org>
+M:	Bin Liu <b-liu@ti.com>
 L:	linux-usb@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git
 S:	Maintained
@@ -7694,13 +7692,13 @@ S:	Maintained
 F:	arch/nios2/
 
 NOKIA N900 POWER SUPPLY DRIVERS
-M:	Pali Rohár <pali.rohar@gmail.com>
-S:	Maintained
+R:	Pali Rohár <pali.rohar@gmail.com>
 F:	include/linux/power/bq2415x_charger.h
 F:	include/linux/power/bq27xxx_battery.h
 F:	include/linux/power/isp1704_charger.h
 F:	drivers/power/bq2415x_charger.c
 F:	drivers/power/bq27xxx_battery.c
+F:	drivers/power/bq27xxx_battery_i2c.c
 F:	drivers/power/isp1704_charger.c
 F:	drivers/power/rx51_battery.c
 
@@ -7931,11 +7929,9 @@ F:	drivers/media/platform/omap3isp/
 F:	drivers/staging/media/omap4iss/
 
 OMAP USB SUPPORT
-M:	Felipe Balbi <balbi@kernel.org>
 L:	linux-usb@vger.kernel.org
 L:	linux-omap@vger.kernel.org
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git
-S:	Maintained
+S:	Orphan
 F:	drivers/usb/*/*omap*
 F:	arch/arm/*omap*/usb*
 
@@ -9566,6 +9562,12 @@ M:	Andreas Noever <andreas.noever@gmail.com>
 S:	Maintained
 F:	drivers/thunderbolt/
 
+TI BQ27XXX POWER SUPPLY DRIVER
+R:	Andrew F. Davis <afd@ti.com>
+F:	include/linux/power/bq27xxx_battery.h
+F:	drivers/power/bq27xxx_battery.c
+F:	drivers/power/bq27xxx_battery_i2c.c
+
 TIMEKEEPING, CLOCKSOURCE CORE, NTP, ALARMTIMER
 M:	John Stultz <john.stultz@linaro.org>
 M:	Thomas Gleixner <tglx@linutronix.de>
@@ -9787,10 +9789,11 @@ S:	Supported
 F:	drivers/scsi/be2iscsi/
 
 Emulex 10Gbps NIC BE2, BE3-R, Lancer, Skyhawk-R DRIVER
-M:	Sathya Perla <sathya.perla@avagotech.com>
-M:	Ajit Khaparde <ajit.khaparde@avagotech.com>
-M:	Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
-M:	Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
+M:	Sathya Perla <sathya.perla@broadcom.com>
+M:	Ajit Khaparde <ajit.khaparde@broadcom.com>
+M:	Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
+M:	Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
+M:	Somnath Kotur <somnath.kotur@broadcom.com>
 L:	netdev@vger.kernel.org
 W:	http://www.emulex.com
 S:	Supported
@@ -12020,7 +12023,6 @@ F:	arch/arm64/xen/
 F:	arch/arm64/include/asm/xen/
 
 XEN NETWORK BACKEND DRIVER
-M:	Ian Campbell <ian.campbell@citrix.com>
 M:	Wei Liu <wei.liu2@citrix.com>
 L:	xen-devel@lists.xenproject.org (moderated for non-subscribers)
 L:	netdev@vger.kernel.org

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 5
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc6
 NAME = Blurry Fish Butt
 
 # *DOCUMENTATION*

arch/arc/Kconfig

@@ -12,8 +12,6 @@ config ARC
 	select BUILDTIME_EXTABLE_SORT
 	select COMMON_CLK
 	select CLONE_BACKWARDS
-	# ARC Busybox based initramfs absolutely relies on DEVTMPFS for /dev
-	select DEVTMPFS if !INITRAMFS_SOURCE=""
 	select GENERIC_ATOMIC64
 	select GENERIC_CLOCKEVENTS
 	select GENERIC_FIND_FIRST_BIT
@@ -275,14 +273,6 @@ config ARC_DCCM_BASE
 	default "0xA0000000"
 	depends on ARC_HAS_DCCM
 
-config ARC_HAS_HW_MPY
-	bool "Use Hardware Multiplier (Normal or Faster XMAC)"
-	default y
-	help
-	  Influences how gcc generates code for MPY operations.
-	  If enabled, MPYxx insns are generated, provided by Standard/XMAC
-	  Multipler. Otherwise software multipy lib is used
-
 choice
 	prompt "MMU Version"
 	default ARC_MMU_V3 if ARC_CPU_770
@@ -338,6 +328,19 @@ config ARC_PAGE_SIZE_4K
 
 endchoice
 
+choice
+	prompt "MMU Super Page Size"
+	depends on ISA_ARCV2 && TRANSPARENT_HUGEPAGE
+	default ARC_HUGEPAGE_2M
+
+config ARC_HUGEPAGE_2M
+	bool "2MB"
+
+config ARC_HUGEPAGE_16M
+	bool "16MB"
+
+endchoice
+
 if ISA_ARCOMPACT
 
 config ARC_COMPACT_IRQ_LEVELS
@@ -410,7 +413,7 @@ config ARC_HAS_RTC
 	default n
 	depends on !SMP
 
-config ARC_HAS_GRTC
+config ARC_HAS_GFRC
 	bool "SMP synchronized 64-bit cycle counter"
 	default y
 	depends on SMP
@@ -529,14 +532,6 @@ config ARC_DBG_TLB_MISS_COUNT
 	  Counts number of I and D TLB Misses and exports them via Debugfs
 	  The counters can be cleared via Debugfs as well
 
-if SMP
-
-config ARC_IPI_DBG
-	bool "Debug Inter Core interrupts"
-	default n
-
-endif
-
 endif
 
 config ARC_UBOOT_SUPPORT
@@ -566,6 +561,12 @@ endmenu
 endmenu	 # "ARC Architecture Configuration"
 
 source "mm/Kconfig"
+
+config FORCE_MAX_ZONEORDER
+	int "Maximum zone order"
+	default "12" if ARC_HUGEPAGE_16M
+	default "11"
+
 source "net/Kconfig"
 source "drivers/Kconfig"
 source "fs/Kconfig"

arch/arc/Makefile

@@ -74,10 +74,6 @@ ldflags-$(CONFIG_CPU_BIG_ENDIAN)	+= -EB
 # --build-id w/o "-marclinux". Default arc-elf32-ld is OK
 ldflags-$(upto_gcc44)			+= -marclinux
 
-ifndef CONFIG_ARC_HAS_HW_MPY
-	cflags-y	+= -mno-mpy
-endif
-
 LIBGCC	:= $(shell $(CC) $(cflags-y) --print-libgcc-file-name)
 
 # Modules with short calls might break for calls into builtin-kernel

arch/arc/configs/axs101_defconfig

@@ -39,6 +39,7 @@ CONFIG_IP_PNP_RARP=y
 # CONFIG_INET_XFRM_MODE_TUNNEL is not set
 # CONFIG_INET_XFRM_MODE_BEET is not set
 # CONFIG_IPV6 is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
@@ -73,7 +74,6 @@ CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 # CONFIG_HWMON is not set
 CONFIG_FB=y
-# CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
 CONFIG_LOGO=y
@@ -91,12 +91,10 @@ CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_DW=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT3_FS=y
-CONFIG_EXT4_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_VFAT_FS=y
 CONFIG_NTFS_FS=y
 CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y

arch/arc/configs/axs103_defconfig

@@ -39,14 +39,10 @@ CONFIG_IP_PNP_RARP=y
 # CONFIG_INET_XFRM_MODE_TUNNEL is not set
 # CONFIG_INET_XFRM_MODE_BEET is not set
 # CONFIG_IPV6 is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_AXS=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_NETDEVICES=y
@@ -78,14 +74,12 @@ CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 # CONFIG_HWMON is not set
 CONFIG_FB=y
-# CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
 CONFIG_LOGO=y
 # CONFIG_LOGO_LINUX_MONO is not set
 # CONFIG_LOGO_LINUX_VGA16 is not set
 # CONFIG_LOGO_LINUX_CLUT224 is not set
-CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_HCD_PLATFORM=y
 CONFIG_USB_OHCI_HCD=y
@@ -97,12 +91,10 @@ CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_DW=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT3_FS=y
-CONFIG_EXT4_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_VFAT_FS=y
 CONFIG_NTFS_FS=y
 CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y

arch/arc/configs/axs103_smp_defconfig

@@ -40,14 +40,10 @@ CONFIG_IP_PNP_RARP=y
 # CONFIG_INET_XFRM_MODE_TUNNEL is not set
 # CONFIG_INET_XFRM_MODE_BEET is not set
 # CONFIG_IPV6 is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_AXS=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_NETDEVICES=y
@@ -79,14 +75,12 @@ CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 # CONFIG_HWMON is not set
 CONFIG_FB=y
-# CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
 CONFIG_LOGO=y
 # CONFIG_LOGO_LINUX_MONO is not set
 # CONFIG_LOGO_LINUX_VGA16 is not set
 # CONFIG_LOGO_LINUX_CLUT224 is not set
-CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_HCD_PLATFORM=y
 CONFIG_USB_OHCI_HCD=y
@@ -98,12 +92,10 @@ CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_DW=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT3_FS=y
-CONFIG_EXT4_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_VFAT_FS=y
 CONFIG_NTFS_FS=y
 CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y

arch/arc/configs/nsim_700_defconfig

@@ -4,6 +4,7 @@ CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
+# CONFIG_CROSS_MEMORY_ATTACH is not set
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
@@ -26,7 +27,6 @@ CONFIG_ARC_PLAT_SIM=y
 CONFIG_ARC_BUILTIN_DTB_NAME="nsim_700"
 CONFIG_PREEMPT=y
 # CONFIG_COMPACTION is not set
-# CONFIG_CROSS_MEMORY_ATTACH is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -34,6 +34,7 @@ CONFIG_UNIX_DIAG=y
 CONFIG_NET_KEY=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
@@ -51,7 +52,6 @@ CONFIG_SERIAL_ARC=y
 CONFIG_SERIAL_ARC_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
-# CONFIG_VGA_CONSOLE is not set
 # CONFIG_HID is not set
 # CONFIG_USB_SUPPORT is not set
 # CONFIG_IOMMU_SUPPORT is not set
@@ -63,4 +63,3 @@ CONFIG_NFS_FS=y
 # CONFIG_ENABLE_WARN_DEPRECATED is not set
 # CONFIG_ENABLE_MUST_CHECK is not set
 # CONFIG_DEBUG_PREEMPT is not set
-CONFIG_XZ_DEC=y

arch/arc/configs/nsim_hs_defconfig

@@ -35,6 +35,7 @@ CONFIG_UNIX_DIAG=y
 CONFIG_NET_KEY=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
@@ -49,7 +50,6 @@ CONFIG_SERIAL_ARC=y
 CONFIG_SERIAL_ARC_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
-# CONFIG_VGA_CONSOLE is not set
 # CONFIG_HID is not set
 # CONFIG_USB_SUPPORT is not set
 # CONFIG_IOMMU_SUPPORT is not set
@@ -61,4 +61,3 @@ CONFIG_NFS_FS=y
 # CONFIG_ENABLE_WARN_DEPRECATED is not set
 # CONFIG_ENABLE_MUST_CHECK is not set
 # CONFIG_DEBUG_PREEMPT is not set
-CONFIG_XZ_DEC=y

arch/arc/configs/nsim_hs_smp_defconfig

@@ -2,6 +2,7 @@ CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
+# CONFIG_CROSS_MEMORY_ATTACH is not set
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
@@ -21,13 +22,11 @@ CONFIG_MODULES=y
 # CONFIG_IOSCHED_DEADLINE is not set
 # CONFIG_IOSCHED_CFQ is not set
 CONFIG_ARC_PLAT_SIM=y
-CONFIG_ARC_BOARD_ML509=y
 CONFIG_ISA_ARCV2=y
 CONFIG_SMP=y
 CONFIG_ARC_BUILTIN_DTB_NAME="nsim_hs_idu"
 CONFIG_PREEMPT=y
 # CONFIG_COMPACTION is not set
-# CONFIG_CROSS_MEMORY_ATTACH is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -35,6 +34,7 @@ CONFIG_UNIX_DIAG=y
 CONFIG_NET_KEY=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
@@ -49,7 +49,6 @@ CONFIG_SERIAL_ARC=y
 CONFIG_SERIAL_ARC_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
-# CONFIG_VGA_CONSOLE is not set
 # CONFIG_HID is not set
 # CONFIG_USB_SUPPORT is not set
 # CONFIG_IOMMU_SUPPORT is not set
@@ -60,4 +59,3 @@ CONFIG_TMPFS=y
 CONFIG_NFS_FS=y
 # CONFIG_ENABLE_WARN_DEPRECATED is not set
 # CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_XZ_DEC=y

arch/arc/configs/nsimosci_defconfig

@@ -33,6 +33,7 @@ CONFIG_UNIX_DIAG=y
 CONFIG_NET_KEY=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
@@ -58,7 +59,6 @@ CONFIG_SERIAL_OF_PLATFORM=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
 CONFIG_FB=y
-# CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
 # CONFIG_HID is not set

arch/arc/configs/nsimosci_hs_defconfig

@@ -34,12 +34,12 @@ CONFIG_UNIX_DIAG=y
 CONFIG_NET_KEY=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
 # CONFIG_BLK_DEV is not set
 CONFIG_NETDEVICES=y
-CONFIG_NET_OSCI_LAN=y
 CONFIG_INPUT_EVDEV=y
 # CONFIG_MOUSE_PS2_ALPS is not set
 # CONFIG_MOUSE_PS2_LOGIPS2PP is not set
@@ -58,7 +58,6 @@ CONFIG_SERIAL_OF_PLATFORM=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
 CONFIG_FB=y
-# CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
 # CONFIG_HID is not set

arch/arc/configs/nsimosci_hs_smp_defconfig

@@ -2,6 +2,7 @@ CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
+# CONFIG_CROSS_MEMORY_ATTACH is not set
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
@@ -18,15 +19,11 @@ CONFIG_MODULES=y
 # CONFIG_IOSCHED_DEADLINE is not set
 # CONFIG_IOSCHED_CFQ is not set
 CONFIG_ARC_PLAT_SIM=y
-CONFIG_ARC_BOARD_ML509=y
 CONFIG_ISA_ARCV2=y
 CONFIG_SMP=y
-CONFIG_ARC_HAS_LL64=y
-# CONFIG_ARC_HAS_RTSC is not set
 CONFIG_ARC_BUILTIN_DTB_NAME="nsimosci_hs_idu"
 CONFIG_PREEMPT=y
 # CONFIG_COMPACTION is not set
-# CONFIG_CROSS_MEMORY_ATTACH is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_PACKET_DIAG=y
@@ -40,6 +37,7 @@ CONFIG_INET=y
 # CONFIG_INET_LRO is not set
 # CONFIG_IPV6 is not set
 # CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
@@ -56,14 +54,11 @@ CONFIG_NETDEVICES=y
 # CONFIG_NET_VENDOR_STMICRO is not set
 # CONFIG_NET_VENDOR_VIA is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
-CONFIG_NET_OSCI_LAN=y
 # CONFIG_WLAN is not set
 CONFIG_INPUT_EVDEV=y
 CONFIG_MOUSE_PS2_TOUCHKIT=y
 # CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIO_LIBPS2=y
 CONFIG_SERIO_ARC_PS2=y
-CONFIG_VT_HW_CONSOLE_BINDING=y
 # CONFIG_LEGACY_PTYS is not set
 # CONFIG_DEVKMEM is not set
 CONFIG_SERIAL_8250=y
@@ -75,9 +70,6 @@ CONFIG_SERIAL_OF_PLATFORM=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
 CONFIG_FB=y
-CONFIG_ARCPGU_RGB888=y
-CONFIG_ARCPGU_DISPTYPE=0
-# CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
 # CONFIG_HID is not set

arch/arc/configs/tb10x_defconfig

@@ -3,6 +3,7 @@ CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="tb10x"
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
+# CONFIG_CROSS_MEMORY_ATTACH is not set
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
@@ -26,12 +27,10 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLOCK is not set
 CONFIG_ARC_PLAT_TB10X=y
 CONFIG_ARC_CACHE_LINE_SHIFT=5
-CONFIG_ARC_STACK_NONEXEC=y
 CONFIG_HZ=250
 CONFIG_ARC_BUILTIN_DTB_NAME="abilis_tb100_dvk"
 CONFIG_PREEMPT_VOLUNTARY=y
 # CONFIG_COMPACTION is not set
-# CONFIG_CROSS_MEMORY_ATTACH is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -44,8 +43,8 @@ CONFIG_IP_MULTICAST=y
 # CONFIG_INET_DIAG is not set
 # CONFIG_IPV6 is not set
 # CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
 # CONFIG_FIRMWARE_IN_KERNEL is not set
-CONFIG_PROC_DEVICETREE=y
 CONFIG_NETDEVICES=y
 # CONFIG_NET_CADENCE is not set
 # CONFIG_NET_VENDOR_BROADCOM is not set
@@ -55,9 +54,6 @@ CONFIG_NETDEVICES=y
 # CONFIG_NET_VENDOR_NATSEMI is not set
 # CONFIG_NET_VENDOR_SEEQ is not set
 CONFIG_STMMAC_ETH=y
-CONFIG_STMMAC_DEBUG_FS=y
-CONFIG_STMMAC_DA=y
-CONFIG_STMMAC_CHAINED=y
 # CONFIG_NET_VENDOR_WIZNET is not set
 # CONFIG_WLAN is not set
 # CONFIG_INPUT is not set
@@ -91,7 +87,6 @@ CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
 CONFIG_LEDS_TRIGGER_TRANSIENT=y
 CONFIG_DMADEVICES=y
 CONFIG_DW_DMAC=y
-CONFIG_NET_DMA=y
 CONFIG_ASYNC_TX_DMA=y
 # CONFIG_IOMMU_SUPPORT is not set
 # CONFIG_DNOTIFY is not set
@@ -100,17 +95,16 @@ CONFIG_TMPFS=y
 CONFIG_CONFIGFS_FS=y
 # CONFIG_MISC_FILESYSTEMS is not set
 # CONFIG_NETWORK_FILESYSTEMS is not set
+CONFIG_DEBUG_INFO=y
 # CONFIG_ENABLE_WARN_DEPRECATED is not set
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_STRIP_ASM_SYMS=y
 CONFIG_DEBUG_FS=y
 CONFIG_HEADERS_CHECK=y
 CONFIG_DEBUG_SECTION_MISMATCH=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_DEBUG_STACKOVERFLOW=y
 CONFIG_DETECT_HUNG_TASK=y
 CONFIG_SCHEDSTATS=y
 CONFIG_TIMER_STATS=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_MEMORY_INIT=y
-CONFIG_DEBUG_STACKOVERFLOW=y
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
 # CONFIG_CRYPTO_HW is not set

arch/arc/configs/vdk_hs38_smp_defconfig

@@ -16,7 +16,7 @@ CONFIG_ARC_PLAT_AXS10X=y
 CONFIG_AXS103=y
 CONFIG_ISA_ARCV2=y
 CONFIG_SMP=y
-# CONFIG_ARC_HAS_GRTC is not set
+# CONFIG_ARC_HAS_GFRC is not set
 CONFIG_ARC_UBOOT_SUPPORT=y
 CONFIG_ARC_BUILTIN_DTB_NAME="vdk_hs38_smp"
 CONFIG_PREEMPT=y

arch/arc/include/asm/arcregs.h

@@ -10,7 +10,8 @@
 #define _ASM_ARC_ARCREGS_H
 
 /* Build Configuration Registers */
-#define ARC_REG_DCCMBASE_BCR	0x61	/* DCCM Base Addr */
+#define ARC_REG_AUX_DCCM	0x18	/* DCCM Base Addr ARCv2 */
+#define ARC_REG_DCCM_BASE_BUILD	0x61	/* DCCM Base Addr ARCompact */
 #define ARC_REG_CRC_BCR		0x62
 #define ARC_REG_VECBASE_BCR	0x68
 #define ARC_REG_PERIBASE_BCR	0x69
@@ -18,10 +19,10 @@
 #define ARC_REG_DPFP_BCR	0x6C	/* ARCompact: Dbl Precision FPU */
 #define ARC_REG_FP_V2_BCR	0xc8	/* ARCv2 FPU */
 #define ARC_REG_SLC_BCR		0xce
-#define ARC_REG_DCCM_BCR	0x74	/* DCCM Present + SZ */
+#define ARC_REG_DCCM_BUILD	0x74	/* DCCM size (common) */
 #define ARC_REG_TIMERS_BCR	0x75
 #define ARC_REG_AP_BCR		0x76
-#define ARC_REG_ICCM_BCR	0x78
+#define ARC_REG_ICCM_BUILD	0x78	/* ICCM size (common) */
 #define ARC_REG_XY_MEM_BCR	0x79
 #define ARC_REG_MAC_BCR		0x7a
 #define ARC_REG_MUL_BCR		0x7b
@@ -36,6 +37,7 @@
 #define ARC_REG_IRQ_BCR		0xF3
 #define ARC_REG_SMART_BCR	0xFF
 #define ARC_REG_CLUSTER_BCR	0xcf
+#define ARC_REG_AUX_ICCM	0x208	/* ICCM Base Addr (ARCv2) */
 
 /* status32 Bits Positions */
 #define STATUS_AE_BIT		5	/* Exception active */
@@ -246,7 +248,7 @@ struct bcr_perip {
 #endif
 };
 
-struct bcr_iccm {
+struct bcr_iccm_arcompact {
 #ifdef CONFIG_CPU_BIG_ENDIAN
 	unsigned int base:16, pad:5, sz:3, ver:8;
 #else
@@ -254,17 +256,15 @@ struct bcr_iccm {
 #endif
 };
 
-/* DCCM Base Address Register: ARC_REG_DCCMBASE_BCR */
-struct bcr_dccm_base {
+struct bcr_iccm_arcv2 {
 #ifdef CONFIG_CPU_BIG_ENDIAN
-	unsigned int addr:24, ver:8;
+	unsigned int pad:8, sz11:4, sz01:4, sz10:4, sz00:4, ver:8;
 #else
-	unsigned int ver:8, addr:24;
+	unsigned int ver:8, sz00:4, sz10:4, sz01:4, sz11:4, pad:8;
 #endif
 };
 
-/* DCCM RAM Configuration Register: ARC_REG_DCCM_BCR */
-struct bcr_dccm {
+struct bcr_dccm_arcompact {
 #ifdef CONFIG_CPU_BIG_ENDIAN
 	unsigned int res:21, sz:3, ver:8;
 #else
@@ -272,6 +272,14 @@ struct bcr_dccm {
 #endif
 };
 
+struct bcr_dccm_arcv2 {
+#ifdef CONFIG_CPU_BIG_ENDIAN
+	unsigned int pad2:12, cyc:3, pad1:1, sz1:4, sz0:4, ver:8;
+#else
+	unsigned int ver:8, sz0:4, sz1:4, pad1:1, cyc:3, pad2:12;
+#endif
+};
+
 /* ARCompact: Both SP and DP FPU BCRs have same format */
 struct bcr_fp_arcompact {
 #ifdef CONFIG_CPU_BIG_ENDIAN
@@ -315,9 +323,9 @@ struct bcr_bpu_arcv2 {
 
 struct bcr_generic {
 #ifdef CONFIG_CPU_BIG_ENDIAN
-	unsigned int pad:24, ver:8;
+	unsigned int info:24, ver:8;
 #else
-	unsigned int ver:8, pad:24;
+	unsigned int ver:8, info:24;
 #endif
 };
 
@@ -349,14 +357,13 @@ struct cpuinfo_arc {
 	struct cpuinfo_arc_bpu bpu;
 	struct bcr_identity core;
 	struct bcr_isa isa;
-	struct bcr_timer timers;
 	unsigned int vec_base;
 	struct cpuinfo_arc_ccm iccm, dccm;
 	struct {
 		unsigned int swap:1, norm:1, minmax:1, barrel:1, crc:1, pad1:3,
 			     fpu_sp:1, fpu_dp:1, pad2:6,
 			     debug:1, ap:1, smart:1, rtt:1, pad3:4,
-			     pad4:8;
+			     timer0:1, timer1:1, rtc:1, gfrc:1, pad4:4;
 	} extn;
 	struct bcr_mpy extn_mpy;
 	struct bcr_extn_xymem extn_xymem;

arch/arc/include/asm/irq.h

@@ -16,11 +16,9 @@
 #ifdef CONFIG_ISA_ARCOMPACT
 #define TIMER0_IRQ      3
 #define TIMER1_IRQ      4
-#define IPI_IRQ		(NR_CPU_IRQS-1) /* dummy to enable SMP build for up hardware */
 #else
 #define TIMER0_IRQ      16
 #define TIMER1_IRQ      17
-#define IPI_IRQ         19
 #endif
 
 #include <linux/interrupt.h>

arch/arc/include/asm/irqflags-arcv2.h

@@ -22,6 +22,7 @@
 #define AUX_IRQ_CTRL		0x00E
 #define AUX_IRQ_ACT		0x043	/* Active Intr across all levels */
 #define AUX_IRQ_LVL_PEND	0x200	/* Pending Intr across all levels */
+#define AUX_IRQ_HINT		0x201	/* For generating Soft Interrupts */
 #define AUX_IRQ_PRIORITY	0x206
 #define ICAUSE			0x40a
 #define AUX_IRQ_SELECT		0x40b
@@ -30,8 +31,11 @@
 /* Was Intr taken in User Mode */
 #define AUX_IRQ_ACT_BIT_U	31
 
-/* 0 is highest level, but taken by FIRQs, if present in design */
-#define ARCV2_IRQ_DEF_PRIO		0
+/*
+ * User space should be interruptable even by lowest prio interrupt
+ * Safe even if actual interrupt priorities is fewer or even one
+ */
+#define ARCV2_IRQ_DEF_PRIO	15
 
 /* seed value for status register */
 #define ISA_INIT_STATUS_BITS	(STATUS_IE_MASK | STATUS_AD_MASK | \
@@ -112,6 +116,16 @@ static inline int arch_irqs_disabled(void)
 	return arch_irqs_disabled_flags(arch_local_save_flags());
 }
 
+static inline void arc_softirq_trigger(int irq)
+{
+	write_aux_reg(AUX_IRQ_HINT, irq);
+}
+
+static inline void arc_softirq_clear(int irq)
+{
+	write_aux_reg(AUX_IRQ_HINT, 0);
+}
+
 #else
 
 .macro IRQ_DISABLE  scratch

arch/arc/include/asm/mcip.h

@@ -39,8 +39,8 @@ struct mcip_cmd {
 #define CMD_DEBUG_SET_MASK		0x34
 #define CMD_DEBUG_SET_SELECT		0x36
 
-#define CMD_GRTC_READ_LO		0x42
-#define CMD_GRTC_READ_HI		0x43
+#define CMD_GFRC_READ_LO		0x42
+#define CMD_GFRC_READ_HI		0x43
 
 #define CMD_IDU_ENABLE			0x71
 #define CMD_IDU_DISABLE			0x72

arch/arc/include/asm/pgtable.h

@@ -179,37 +179,44 @@
 #define __S111  PAGE_U_X_W_R
 
 /****************************************************************
- * Page Table Lookup split
+ * 2 tier (PGD:PTE) software page walker
  *
- * We implement 2 tier paging and since this is all software, we are free
- * to customize the span of a PGD / PTE entry to suit us
- *
- *			32 bit virtual address
+ * [31]		    32 bit virtual address              [0]
  * -------------------------------------------------------
- * | BITS_FOR_PGD    |  BITS_FOR_PTE    |  BITS_IN_PAGE  |
+ * |               | <------------ PGDIR_SHIFT ----------> |
+ * |		   |					 |
+ * | BITS_FOR_PGD  |  BITS_FOR_PTE  | <-- PAGE_SHIFT --> |
  * -------------------------------------------------------
  *       |                  |                |
  *       |                  |                --> off in page frame
- *       |		    |
  *       |                  ---> index into Page Table
- *       |
  *       ----> index into Page Directory
+ *
+ * In a single page size configuration, only PAGE_SHIFT is fixed
+ * So both PGD and PTE sizing can be tweaked
+ *  e.g. 8K page (PAGE_SHIFT 13) can have
+ *  - PGDIR_SHIFT 21  -> 11:8:13 address split
+ *  - PGDIR_SHIFT 24  -> 8:11:13 address split
+ *
+ * If Super Page is configured, PGDIR_SHIFT becomes fixed too,
+ * so the sizing flexibility is gone.
  */
 
-#define BITS_IN_PAGE	PAGE_SHIFT
-
-/* Optimal Sizing of Pg Tbl - based on MMU page size */
-#if defined(CONFIG_ARC_PAGE_SIZE_8K)
-#define BITS_FOR_PTE	8		/* 11:8:13 */
-#elif defined(CONFIG_ARC_PAGE_SIZE_16K)
-#define BITS_FOR_PTE	8		/* 10:8:14 */
-#elif defined(CONFIG_ARC_PAGE_SIZE_4K)
-#define BITS_FOR_PTE	9		/* 11:9:12 */
+#if defined(CONFIG_ARC_HUGEPAGE_16M)
+#define PGDIR_SHIFT	24
+#elif defined(CONFIG_ARC_HUGEPAGE_2M)
+#define PGDIR_SHIFT	21
+#else
+/*
+ * Only Normal page support so "hackable" (see comment above)
+ * Default value provides 11:8:13 (8K), 11:9:12 (4K)
+ */
+#define PGDIR_SHIFT	21
 #endif
 
-#define BITS_FOR_PGD	(32 - BITS_FOR_PTE - BITS_IN_PAGE)
+#define BITS_FOR_PTE	(PGDIR_SHIFT - PAGE_SHIFT)
+#define BITS_FOR_PGD	(32 - PGDIR_SHIFT)
 
-#define PGDIR_SHIFT	(32 - BITS_FOR_PGD)
 #define PGDIR_SIZE	(1UL << PGDIR_SHIFT)	/* vaddr span, not PDG sz */
 #define PGDIR_MASK	(~(PGDIR_SIZE-1))
 

arch/arc/kernel/entry-arcv2.S

@@ -45,11 +45,12 @@ VECTOR	reserved		; Reserved slots
 VECTOR	handle_interrupt	; (16) Timer0
 VECTOR	handle_interrupt	; unused (Timer1)
 VECTOR	handle_interrupt	; unused (WDT)
-VECTOR	handle_interrupt	; (19) ICI (inter core interrupt)
-VECTOR	handle_interrupt
-VECTOR	handle_interrupt
-VECTOR	handle_interrupt
-VECTOR	handle_interrupt	; (23) End of fixed IRQs
+VECTOR	handle_interrupt	; (19) Inter core Interrupt (IPI)
+VECTOR	handle_interrupt	; (20) perf Interrupt
+VECTOR	handle_interrupt	; (21) Software Triggered Intr (Self IPI)
+VECTOR	handle_interrupt	; unused
+VECTOR	handle_interrupt	; (23) unused
+# End of fixed IRQs
 
 .rept CONFIG_ARC_NUMBER_OF_INTERRUPTS - 8
 	VECTOR	handle_interrupt
@@ -211,7 +212,11 @@ debug_marker_syscall:
 ; (since IRQ NOT allowed in DS in ARCv2, this can only happen if orig
 ; entry was via Exception in DS which got preempted in kernel).
 ;
-; IRQ RTIE won't reliably restore DE bit and/or BTA, needs handling
+; IRQ RTIE won't reliably restore DE bit and/or BTA, needs workaround
+;
+; Solution is return from Intr w/o any delay slot quirks into a kernel trampoline
+; and from pure kernel mode return to delay slot which handles DS bit/BTA correctly
+
 .Lintr_ret_to_delay_slot:
 debug_marker_ds:
 
@@ -222,18 +227,23 @@ debug_marker_ds:
 	ld	r2, [sp, PT_ret]
 	ld	r3, [sp, PT_status32]
 
+	; STAT32 for Int return created from scratch
+	; (No delay dlot, disable Further intr in trampoline)
+
 	bic  	r0, r3, STATUS_U_MASK|STATUS_DE_MASK|STATUS_IE_MASK|STATUS_L_MASK
 	st	r0, [sp, PT_status32]
 
 	mov	r1, .Lintr_ret_to_delay_slot_2
 	st	r1, [sp, PT_ret]
 
+	; Orig exception PC/STAT32 safekept @orig_r0 and @event stack slots
 	st	r2, [sp, 0]
 	st	r3, [sp, 4]
 
 	b	.Lisr_ret_fast_path
 
 .Lintr_ret_to_delay_slot_2:
+	; Trampoline to restore orig exception PC/STAT32/BTA/AUX_USER_SP
 	sub	sp, sp, SZ_PT_REGS
 	st	r9, [sp, -4]
 
@@ -243,11 +253,19 @@ debug_marker_ds:
 	ld	r9, [sp, 4]
 	sr	r9, [erstatus]
 
+	; restore AUX_USER_SP if returning to U mode
+	bbit0	r9, STATUS_U_BIT, 1f
+	ld	r9, [sp, PT_sp]
+	sr	r9, [AUX_USER_SP]
+
+1:
 	ld	r9, [sp, 8]
 	sr	r9, [erbta]
 
 	ld	r9, [sp, -4]
 	add	sp, sp, SZ_PT_REGS
+
+	; return from pure kernel mode to delay slot
 	rtie
 
 END(ret_from_exception)

arch/arc/kernel/intc-arcv2.c

@@ -14,6 +14,8 @@
 #include <linux/irqchip.h>
 #include <asm/irq.h>
 
+static int irq_prio;
+
 /*
  * Early Hardware specific Interrupt setup
  * -Called very early (start_kernel -> setup_arch -> setup_processor)
@@ -24,6 +26,14 @@ void arc_init_IRQ(void)
 {
 	unsigned int tmp;
 
+	struct irq_build {
+#ifdef CONFIG_CPU_BIG_ENDIAN
+		unsigned int pad:3, firq:1, prio:4, exts:8, irqs:8, ver:8;
+#else
+		unsigned int ver:8, irqs:8, exts:8, prio:4, firq:1, pad:3;
+#endif
+	} irq_bcr;
+
 	struct aux_irq_ctrl {
 #ifdef CONFIG_CPU_BIG_ENDIAN
 		unsigned int res3:18, save_idx_regs:1, res2:1,
@@ -46,28 +56,25 @@ void arc_init_IRQ(void)
 
 	WRITE_AUX(AUX_IRQ_CTRL, ictrl);
 
-	/* setup status32, don't enable intr yet as kernel doesn't want */
-	tmp = read_aux_reg(0xa);
-	tmp |= ISA_INIT_STATUS_BITS;
-	tmp &= ~STATUS_IE_MASK;
-	asm volatile("flag %0	\n"::"r"(tmp));
-
 	/*
 	 * ARCv2 core intc provides multiple interrupt priorities (upto 16).
 	 * Typical builds though have only two levels (0-high, 1-low)
 	 * Linux by default uses lower prio 1 for most irqs, reserving 0 for
 	 * NMI style interrupts in future (say perf)
-	 *
-	 * Read the intc BCR to confirm that Linux default priority is avail
-	 * in h/w
-	 *
-	 * Note:
-	 *  IRQ_BCR[27..24] contains N-1 (for N priority levels) and prio level
-	 *  is 0 based.
 	 */
-	tmp = (read_aux_reg(ARC_REG_IRQ_BCR) >> 24 ) & 0xF;
-	if (ARCV2_IRQ_DEF_PRIO > tmp)
-		panic("Linux default irq prio incorrect\n");
+
+	READ_BCR(ARC_REG_IRQ_BCR, irq_bcr);
+
+	irq_prio = irq_bcr.prio;	/* Encoded as N-1 for N levels */
+	pr_info("archs-intc\t: %d priority levels (default %d)%s\n",
+		irq_prio + 1, irq_prio,
+		irq_bcr.firq ? " FIRQ (not used)":"");
+
+	/* setup status32, don't enable intr yet as kernel doesn't want */
+	tmp = read_aux_reg(0xa);
+	tmp |= STATUS_AD_MASK | (irq_prio << 1);
+	tmp &= ~STATUS_IE_MASK;
+	asm volatile("flag %0	\n"::"r"(tmp));
 }
 
 static void arcv2_irq_mask(struct irq_data *data)
@@ -86,7 +93,7 @@ void arcv2_irq_enable(struct irq_data *data)
 {
 	/* set default priority */
 	write_aux_reg(AUX_IRQ_SELECT, data->irq);
-	write_aux_reg(AUX_IRQ_PRIORITY, ARCV2_IRQ_DEF_PRIO);
+	write_aux_reg(AUX_IRQ_PRIORITY, irq_prio);
 
 	/*
 	 * hw auto enables (linux unmask) all by default

arch/arc/kernel/intc-compact.c

@@ -81,9 +81,6 @@ static int arc_intc_domain_map(struct irq_domain *d, unsigned int irq,
 {
 	switch (irq) {
 	case TIMER0_IRQ:
-#ifdef CONFIG_SMP
-	case IPI_IRQ:
-#endif
 		irq_set_chip_and_handler(irq, &onchip_intc, handle_percpu_irq);
 		break;
 	default:

arch/arc/kernel/mcip.c

@@ -11,9 +11,13 @@
 #include <linux/smp.h>
 #include <linux/irq.h>
 #include <linux/spinlock.h>
+#include <asm/irqflags-arcv2.h>
 #include <asm/mcip.h>
 #include <asm/setup.h>
 
+#define IPI_IRQ		19
+#define SOFTIRQ_IRQ	21
+
 static char smp_cpuinfo_buf[128];
 static int idu_detected;
 
@@ -22,6 +26,7 @@ static DEFINE_RAW_SPINLOCK(mcip_lock);
 static void mcip_setup_per_cpu(int cpu)
 {
 	smp_ipi_irq_setup(cpu, IPI_IRQ);
+	smp_ipi_irq_setup(cpu, SOFTIRQ_IRQ);
 }
 
 static void mcip_ipi_send(int cpu)
@@ -29,46 +34,44 @@ static void mcip_ipi_send(int cpu)
 	unsigned long flags;
 	int ipi_was_pending;
 
+	/* ARConnect can only send IPI to others */
+	if (unlikely(cpu == raw_smp_processor_id())) {
+		arc_softirq_trigger(SOFTIRQ_IRQ);
+		return;
+	}
+
+	raw_spin_lock_irqsave(&mcip_lock, flags);
+
 	/*
-	 * NOTE: We must spin here if the other cpu hasn't yet
-	 * serviced a previous message. This can burn lots
-	 * of time, but we MUST follows this protocol or
-	 * ipi messages can be lost!!!
-	 * Also, we must release the lock in this loop because
-	 * the other side may get to this same loop and not
-	 * be able to ack -- thus causing deadlock.
+	 * If receiver already has a pending interrupt, elide sending this one.
+	 * Linux cross core calling works well with concurrent IPIs
+	 * coalesced into one
+	 * see arch/arc/kernel/smp.c: ipi_send_msg_one()
 	 */
+	__mcip_cmd(CMD_INTRPT_READ_STATUS, cpu);
+	ipi_was_pending = read_aux_reg(ARC_REG_MCIP_READBACK);
+	if (!ipi_was_pending)
+		__mcip_cmd(CMD_INTRPT_GENERATE_IRQ, cpu);
 
-	do {
-		raw_spin_lock_irqsave(&mcip_lock, flags);
-		__mcip_cmd(CMD_INTRPT_READ_STATUS, cpu);
-		ipi_was_pending = read_aux_reg(ARC_REG_MCIP_READBACK);
-		if (ipi_was_pending == 0)
-			break; /* break out but keep lock */
-		raw_spin_unlock_irqrestore(&mcip_lock, flags);
-	} while (1);
-
-	__mcip_cmd(CMD_INTRPT_GENERATE_IRQ, cpu);
 	raw_spin_unlock_irqrestore(&mcip_lock, flags);
-
-#ifdef CONFIG_ARC_IPI_DBG
-	if (ipi_was_pending)
-		pr_info("IPI ACK delayed from cpu %d\n", cpu);
-#endif
 }
 
 static void mcip_ipi_clear(int irq)
 {
 	unsigned int cpu, c;
 	unsigned long flags;
-	unsigned int __maybe_unused copy;
+
+	if (unlikely(irq == SOFTIRQ_IRQ)) {
+		arc_softirq_clear(irq);
+		return;
+	}
 
 	raw_spin_lock_irqsave(&mcip_lock, flags);
 
 	/* Who sent the IPI */
 	__mcip_cmd(CMD_INTRPT_CHECK_SOURCE, 0);
 
-	copy = cpu = read_aux_reg(ARC_REG_MCIP_READBACK);	/* 1,2,4,8... */
+	cpu = read_aux_reg(ARC_REG_MCIP_READBACK);	/* 1,2,4,8... */
 
 	/*
 	 * In rare case, multiple concurrent IPIs sent to same target can
@@ -82,12 +85,6 @@ static void mcip_ipi_clear(int irq)
 	} while (cpu);
 
 	raw_spin_unlock_irqrestore(&mcip_lock, flags);
-
-#ifdef CONFIG_ARC_IPI_DBG
-	if (c != __ffs(copy))
-		pr_info("IPIs from %x coalesced to %x\n",
-			copy, raw_smp_processor_id());
-#endif
 }
 
 static void mcip_probe_n_setup(void)
@@ -96,13 +93,13 @@ static void mcip_probe_n_setup(void)
 #ifdef CONFIG_CPU_BIG_ENDIAN
 		unsigned int pad3:8,
 			     idu:1, llm:1, num_cores:6,
-			     iocoh:1,  grtc:1, dbg:1, pad2:1,
+			     iocoh:1,  gfrc:1, dbg:1, pad2:1,
 			     msg:1, sem:1, ipi:1, pad:1,
 			     ver:8;
 #else
 		unsigned int ver:8,
 			     pad:1, ipi:1, sem:1, msg:1,
-			     pad2:1, dbg:1, grtc:1, iocoh:1,
+			     pad2:1, dbg:1, gfrc:1, iocoh:1,
 			     num_cores:6, llm:1, idu:1,
 			     pad3:8;
 #endif
@@ -111,12 +108,13 @@ static void mcip_probe_n_setup(void)
 	READ_BCR(ARC_REG_MCIP_BCR, mp);
 
 	sprintf(smp_cpuinfo_buf,
-		"Extn [SMP]\t: ARConnect (v%d): %d cores with %s%s%s%s\n",
+		"Extn [SMP]\t: ARConnect (v%d): %d cores with %s%s%s%s%s\n",
 		mp.ver, mp.num_cores,
 		IS_AVAIL1(mp.ipi, "IPI "),
 		IS_AVAIL1(mp.idu, "IDU "),
+		IS_AVAIL1(mp.llm, "LLM "),
 		IS_AVAIL1(mp.dbg, "DEBUG "),
-		IS_AVAIL1(mp.grtc, "GRTC"));
+		IS_AVAIL1(mp.gfrc, "GFRC"));
 
 	idu_detected = mp.idu;
 
@@ -125,8 +123,8 @@ static void mcip_probe_n_setup(void)
 		__mcip_cmd_data(CMD_DEBUG_SET_MASK, 0xf, 0xf);
 	}
 
-	if (IS_ENABLED(CONFIG_ARC_HAS_GRTC) && !mp.grtc)
-		panic("kernel trying to use non-existent GRTC\n");
+	if (IS_ENABLED(CONFIG_ARC_HAS_GFRC) && !mp.gfrc)
+		panic("kernel trying to use non-existent GFRC\n");
 }
 
 struct plat_smp_ops plat_smp_ops = {

arch/arc/kernel/setup.c

@@ -42,9 +42,57 @@ struct task_struct *_current_task[NR_CPUS];	/* For stack switching */
 
 struct cpuinfo_arc cpuinfo_arc700[NR_CPUS];
 
+static void read_decode_ccm_bcr(struct cpuinfo_arc *cpu)
+{
+	if (is_isa_arcompact()) {
+		struct bcr_iccm_arcompact iccm;
+		struct bcr_dccm_arcompact dccm;
+
+		READ_BCR(ARC_REG_ICCM_BUILD, iccm);
+		if (iccm.ver) {
+			cpu->iccm.sz = 4096 << iccm.sz;	/* 8K to 512K */
+			cpu->iccm.base_addr = iccm.base << 16;
+		}
+
+		READ_BCR(ARC_REG_DCCM_BUILD, dccm);
+		if (dccm.ver) {
+			unsigned long base;
+			cpu->dccm.sz = 2048 << dccm.sz;	/* 2K to 256K */
+
+			base = read_aux_reg(ARC_REG_DCCM_BASE_BUILD);
+			cpu->dccm.base_addr = base & ~0xF;
+		}
+	} else {
+		struct bcr_iccm_arcv2 iccm;
+		struct bcr_dccm_arcv2 dccm;
+		unsigned long region;
+
+		READ_BCR(ARC_REG_ICCM_BUILD, iccm);
+		if (iccm.ver) {
+			cpu->iccm.sz = 256 << iccm.sz00;	/* 512B to 16M */
+			if (iccm.sz00 == 0xF && iccm.sz01 > 0)
+				cpu->iccm.sz <<= iccm.sz01;
+
+			region = read_aux_reg(ARC_REG_AUX_ICCM);
+			cpu->iccm.base_addr = region & 0xF0000000;
+		}
+
+		READ_BCR(ARC_REG_DCCM_BUILD, dccm);
+		if (dccm.ver) {
+			cpu->dccm.sz = 256 << dccm.sz0;
+			if (dccm.sz0 == 0xF && dccm.sz1 > 0)
+				cpu->dccm.sz <<= dccm.sz1;
+
+			region = read_aux_reg(ARC_REG_AUX_DCCM);
+			cpu->dccm.base_addr = region & 0xF0000000;
+		}
+	}
+}
+
 static void read_arc_build_cfg_regs(void)
 {
 	struct bcr_perip uncached_space;
+	struct bcr_timer timer;
 	struct bcr_generic bcr;
 	struct cpuinfo_arc *cpu = &cpuinfo_arc700[smp_processor_id()];
 	unsigned long perip_space;
@@ -53,7 +101,11 @@ static void read_arc_build_cfg_regs(void)
 	READ_BCR(AUX_IDENTITY, cpu->core);
 	READ_BCR(ARC_REG_ISA_CFG_BCR, cpu->isa);
 
-	READ_BCR(ARC_REG_TIMERS_BCR, cpu->timers);
+	READ_BCR(ARC_REG_TIMERS_BCR, timer);
+	cpu->extn.timer0 = timer.t0;
+	cpu->extn.timer1 = timer.t1;
+	cpu->extn.rtc = timer.rtc;
+
 	cpu->vec_base = read_aux_reg(AUX_INTR_VEC_BASE);
 
 	READ_BCR(ARC_REG_D_UNCACH_BCR, uncached_space);
@@ -71,36 +123,11 @@ static void read_arc_build_cfg_regs(void)
 	cpu->extn.swap = read_aux_reg(ARC_REG_SWAP_BCR) ? 1 : 0;        /* 1,3 */
 	cpu->extn.crc = read_aux_reg(ARC_REG_CRC_BCR) ? 1 : 0;
 	cpu->extn.minmax = read_aux_reg(ARC_REG_MIXMAX_BCR) > 1 ? 1 : 0; /* 2 */
-
-	/* Note that we read the CCM BCRs independent of kernel config
-	 * This is to catch the cases where user doesn't know that
-	 * CCMs are present in hardware build
-	 */
-	{
-		struct bcr_iccm iccm;
-		struct bcr_dccm dccm;
-		struct bcr_dccm_base dccm_base;
-		unsigned int bcr_32bit_val;
-
-		bcr_32bit_val = read_aux_reg(ARC_REG_ICCM_BCR);
-		if (bcr_32bit_val) {
-			iccm = *((struct bcr_iccm *)&bcr_32bit_val);
-			cpu->iccm.base_addr = iccm.base << 16;
-			cpu->iccm.sz = 0x2000 << (iccm.sz - 1);
-		}
-
-		bcr_32bit_val = read_aux_reg(ARC_REG_DCCM_BCR);
-		if (bcr_32bit_val) {
-			dccm = *((struct bcr_dccm *)&bcr_32bit_val);
-			cpu->dccm.sz = 0x800 << (dccm.sz);
-
-			READ_BCR(ARC_REG_DCCMBASE_BCR, dccm_base);
-			cpu->dccm.base_addr = dccm_base.addr << 8;
-		}
-	}
-
 	READ_BCR(ARC_REG_XY_MEM_BCR, cpu->extn_xymem);
 
+	/* Read CCM BCRs for boot reporting even if not enabled in Kconfig */
+	read_decode_ccm_bcr(cpu);
+
 	read_decode_mmu_bcr();
 	read_decode_cache_bcr();
 
@@ -208,9 +235,9 @@ static char *arc_cpu_mumbojumbo(int cpu_id, char *buf, int len)
 		       (unsigned int)(arc_get_core_freq() / 10000) % 100);
 
 	n += scnprintf(buf + n, len - n, "Timers\t\t: %s%s%s%s\nISA Extn\t: ",
-		       IS_AVAIL1(cpu->timers.t0, "Timer0 "),
-		       IS_AVAIL1(cpu->timers.t1, "Timer1 "),
-		       IS_AVAIL2(cpu->timers.rtc, "64-bit RTC ",
+		       IS_AVAIL1(cpu->extn.timer0, "Timer0 "),
+		       IS_AVAIL1(cpu->extn.timer1, "Timer1 "),
+		       IS_AVAIL2(cpu->extn.rtc, "Local-64-bit-Ctr ",
 				 CONFIG_ARC_HAS_RTC));
 
 	n += i = scnprintf(buf + n, len - n, "%s%s%s%s%s",
@@ -232,8 +259,6 @@ static char *arc_cpu_mumbojumbo(int cpu_id, char *buf, int len)
 
 			n += scnprintf(buf + n, len - n, "mpy[opt %d] ", opt);
 		}
-		n += scnprintf(buf + n, len - n, "%s",
-			       IS_USED_CFG(CONFIG_ARC_HAS_HW_MPY));
 	}
 
 	n += scnprintf(buf + n, len - n, "%s%s%s%s%s%s%s%s\n",
@@ -293,13 +318,13 @@ static void arc_chk_core_config(void)
 	struct cpuinfo_arc *cpu = &cpuinfo_arc700[smp_processor_id()];
 	int fpu_enabled;
 
-	if (!cpu->timers.t0)
+	if (!cpu->extn.timer0)
 		panic("Timer0 is not present!\n");
 
-	if (!cpu->timers.t1)
+	if (!cpu->extn.timer1)
 		panic("Timer1 is not present!\n");
 
-	if (IS_ENABLED(CONFIG_ARC_HAS_RTC) && !cpu->timers.rtc)
+	if (IS_ENABLED(CONFIG_ARC_HAS_RTC) && !cpu->extn.rtc)
 		panic("RTC is not present\n");
 
 #ifdef CONFIG_ARC_HAS_DCCM
@@ -334,6 +359,7 @@ static void arc_chk_core_config(void)
 		panic("FPU non-existent, disable CONFIG_ARC_FPU_SAVE_RESTORE\n");
 
 	if (is_isa_arcv2() && IS_ENABLED(CONFIG_SMP) && cpu->isa.atomic &&
+	    IS_ENABLED(CONFIG_ARC_HAS_LLSC) &&
 	    !IS_ENABLED(CONFIG_ARC_STAR_9000923308))
 		panic("llock/scond livelock workaround missing\n");
 }

arch/arc/kernel/smp.c

@@ -336,11 +336,8 @@ irqreturn_t do_IPI(int irq, void *dev_id)
 		int rc;
 
 		rc = __do_IPI(msg);
-#ifdef CONFIG_ARC_IPI_DBG
-		/* IPI received but no valid @msg */
 		if (rc)
 			pr_info("IPI with bogus msg %ld in %ld\n", msg, copy);
-#endif
 		pending &= ~(1U << msg);
 	} while (pending);
 

arch/arc/kernel/time.c

@@ -62,7 +62,7 @@
 
 /********** Clock Source Device *********/
 
-#ifdef CONFIG_ARC_HAS_GRTC
+#ifdef CONFIG_ARC_HAS_GFRC
 
 static int arc_counter_setup(void)
 {
@@ -83,10 +83,10 @@ static cycle_t arc_counter_read(struct clocksource *cs)
 
 	local_irq_save(flags);
 
-	__mcip_cmd(CMD_GRTC_READ_LO, 0);
+	__mcip_cmd(CMD_GFRC_READ_LO, 0);
 	stamp.l = read_aux_reg(ARC_REG_MCIP_READBACK);
 
-	__mcip_cmd(CMD_GRTC_READ_HI, 0);
+	__mcip_cmd(CMD_GFRC_READ_HI, 0);
 	stamp.h = read_aux_reg(ARC_REG_MCIP_READBACK);
 
 	local_irq_restore(flags);
@@ -95,7 +95,7 @@ static cycle_t arc_counter_read(struct clocksource *cs)
 }
 
 static struct clocksource arc_counter = {
-	.name   = "ARConnect GRTC",
+	.name   = "ARConnect GFRC",
 	.rating = 400,
 	.read   = arc_counter_read,
 	.mask   = CLOCKSOURCE_MASK(64),

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -285,8 +285,10 @@
 	};
 };
 
+
+/include/ "tps65217.dtsi"
+
 &tps {
-	compatible = "ti,tps65217";
 	/*
 	 * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only
 	 * mode") at poweroff.  Most BeagleBone versions do not support RTC-only
@@ -307,17 +309,12 @@
 	ti,pmic-shutdown-controller;
 
 	regulators {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		dcdc1_reg: regulator@0 {
-			reg = <0>;
 			regulator-name = "vdds_dpr";
 			regulator-always-on;
 		};
 
 		dcdc2_reg: regulator@1 {
-			reg = <1>;
 			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <925000>;
@@ -327,7 +324,6 @@
 		};
 
 		dcdc3_reg: regulator@2 {
-			reg = <2>;
 			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
 			regulator-name = "vdd_core";
 			regulator-min-microvolt = <925000>;
@@ -337,25 +333,21 @@
 		};
 
 		ldo1_reg: regulator@3 {
-			reg = <3>;
 			regulator-name = "vio,vrtc,vdds";
 			regulator-always-on;
 		};
 
 		ldo2_reg: regulator@4 {
-			reg = <4>;
 			regulator-name = "vdd_3v3aux";
 			regulator-always-on;
 		};
 
 		ldo3_reg: regulator@5 {
-			reg = <5>;
 			regulator-name = "vdd_1v8";
 			regulator-always-on;
 		};
 
 		ldo4_reg: regulator@6 {
-			reg = <6>;
 			regulator-name = "vdd_3v3a";
 			regulator-always-on;
 		};

arch/arm/boot/dts/am335x-chilisom.dtsi

@@ -128,21 +128,16 @@
 
 };
 
-&tps {
-	compatible = "ti,tps65217";
+/include/ "tps65217.dtsi"
 
+&tps {
 	regulators {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		dcdc1_reg: regulator@0 {
-			reg = <0>;
 			regulator-name = "vdds_dpr";
 			regulator-always-on;
 		};
 
 		dcdc2_reg: regulator@1 {
-			reg = <1>;
 			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <925000>;
@@ -152,7 +147,6 @@
 		};
 
 		dcdc3_reg: regulator@2 {
-			reg = <2>;
 			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
 			regulator-name = "vdd_core";
 			regulator-min-microvolt = <925000>;
@@ -162,28 +156,24 @@
 		};
 
 		ldo1_reg: regulator@3 {
-			reg = <3>;
 			regulator-name = "vio,vrtc,vdds";
 			regulator-boot-on;
 			regulator-always-on;
 		};
 
 		ldo2_reg: regulator@4 {
-			reg = <4>;
 			regulator-name = "vdd_3v3aux";
 			regulator-boot-on;
 			regulator-always-on;
 		};
 
 		ldo3_reg: regulator@5 {
-			reg = <5>;
 			regulator-name = "vdd_1v8";
 			regulator-boot-on;
 			regulator-always-on;
 		};
 
 		ldo4_reg: regulator@6 {
-			reg = <6>;
 			regulator-name = "vdd_3v3d";
 			regulator-boot-on;
 			regulator-always-on;

arch/arm/boot/dts/am335x-nano.dts

@@ -375,15 +375,11 @@
 	wp-gpios = <&gpio3 18 0>;
 };
 
-&tps {
-	compatible = "ti,tps65217";
+#include "tps65217.dtsi"
 
+&tps {
 	regulators {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		dcdc1_reg: regulator@0 {
-			reg = <0>;
 			/* +1.5V voltage with ±4% tolerance */
 			regulator-min-microvolt = <1450000>;
 			regulator-max-microvolt = <1550000>;
@@ -392,7 +388,6 @@
 		};
 
 		dcdc2_reg: regulator@1 {
-			reg = <1>;
 			/* VDD_MPU voltage limits 0.95V - 1.1V with ±4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <915000>;
@@ -402,7 +397,6 @@
 		};
 
 		dcdc3_reg: regulator@2 {
-			reg = <2>;
 			/* VDD_CORE voltage limits 0.95V - 1.1V with ±4% tolerance */
 			regulator-name = "vdd_core";
 			regulator-min-microvolt = <915000>;
@@ -412,7 +406,6 @@
 		};
 
 		ldo1_reg: regulator@3 {
-			reg = <3>;
 			/* +1.8V voltage with ±4% tolerance */
 			regulator-min-microvolt = <1750000>;
 			regulator-max-microvolt = <1870000>;
@@ -421,7 +414,6 @@
 		};
 
 		ldo2_reg: regulator@4 {
-			reg = <4>;
 			/* +3.3V voltage with ±4% tolerance */
 			regulator-min-microvolt = <3175000>;
 			regulator-max-microvolt = <3430000>;
@@ -430,7 +422,6 @@
 		};
 
 		ldo3_reg: regulator@5 {
-			reg = <5>;
 			/* +1.8V voltage with ±4% tolerance */
 			regulator-min-microvolt = <1750000>;
 			regulator-max-microvolt = <1870000>;
@@ -439,7 +430,6 @@
 		};
 
 		ldo4_reg: regulator@6 {
-			reg = <6>;
 			/* +3.3V voltage with ±4% tolerance */
 			regulator-min-microvolt = <3175000>;
 			regulator-max-microvolt = <3430000>;

arch/arm/boot/dts/am335x-pepper.dts

@@ -420,9 +420,9 @@
 	vin-supply = <&vbat>;
 };
 
-&tps {
-	compatible = "ti,tps65217";
+/include/ "tps65217.dtsi"
 
+&tps {
 	backlight {
 		isel = <1>; /* ISET1 */
 		fdim = <200>; /* TPS65217_BL_FDIM_200HZ */
@@ -430,17 +430,12 @@
 	};
 
 	regulators {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		dcdc1_reg: regulator@0 {
-			reg = <0>;
 			/* VDD_1V8 system supply */
 			regulator-always-on;
 		};
 
 		dcdc2_reg: regulator@1 {
-			reg = <1>;
 			/* VDD_CORE voltage limits 0.95V - 1.26V with +/-4% tolerance */
 			regulator-name = "vdd_core";
 			regulator-min-microvolt = <925000>;
@@ -450,7 +445,6 @@
 		};
 
 		dcdc3_reg: regulator@2 {
-			reg = <2>;
 			/* VDD_MPU voltage limits 0.95V - 1.1V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <925000>;
@@ -460,21 +454,18 @@
 		};
 
 		ldo1_reg: regulator@3 {
-			reg = <3>;
 			/* VRTC 1.8V always-on supply */
 			regulator-name = "vrtc,vdds";
 			regulator-always-on;
 		};
 
 		ldo2_reg: regulator@4 {
-			reg = <4>;
 			/* 3.3V rail */
 			regulator-name = "vdd_3v3aux";
 			regulator-always-on;
 		};
 
 		ldo3_reg: regulator@5 {
-			reg = <5>;
 			/* VDD_3V3A 3.3V rail */
 			regulator-name = "vdd_3v3a";
 			regulator-min-microvolt = <3300000>;
@@ -482,7 +473,6 @@
 		};
 
 		ldo4_reg: regulator@6 {
-			reg = <6>;
 			/* VDD_3V3B 3.3V rail */
 			regulator-name = "vdd_3v3b";
 			regulator-always-on;

arch/arm/boot/dts/am335x-shc.dts

@@ -46,7 +46,7 @@
 			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_BACK>;
 			debounce-interval = <1000>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		front_button {
@@ -54,7 +54,7 @@
 			gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_FRONT>;
 			debounce-interval = <1000>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/am335x-sl50.dts

@@ -375,19 +375,16 @@
 	pinctrl-0 = <&uart4_pins>;
 };
 
+#include "tps65217.dtsi"
+
 &tps {
-	compatible = "ti,tps65217";
 	ti,pmic-shutdown-controller;
 
 	interrupt-parent = <&intc>;
 	interrupts = <7>;	/* NNMI */
 
 	regulators {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		dcdc1_reg: regulator@0 {
-			reg = <0>;
 			/* VDDS_DDR */
 			regulator-min-microvolt = <1500000>;
 			regulator-max-microvolt = <1500000>;
@@ -395,7 +392,6 @@
 		};
 
 		dcdc2_reg: regulator@1 {
-			reg = <1>;
 			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <925000>;
@@ -405,7 +401,6 @@
 		};
 
 		dcdc3_reg: regulator@2 {
-			reg = <2>;
 			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
 			regulator-name = "vdd_core";
 			regulator-min-microvolt = <925000>;
@@ -415,7 +410,6 @@
 		};
 
 		ldo1_reg: regulator@3 {
-			reg = <3>;
 			/* VRTC / VIO / VDDS*/
 			regulator-always-on;
 			regulator-min-microvolt = <1800000>;
@@ -423,7 +417,6 @@
 		};
 
 		ldo2_reg: regulator@4 {
-			reg = <4>;
 			/* VDD_3V3AUX */
 			regulator-always-on;
 			regulator-min-microvolt = <3300000>;
@@ -431,7 +424,6 @@
 		};
 
 		ldo3_reg: regulator@5 {
-			reg = <5>;
 			/* VDD_1V8 */
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
@@ -439,7 +431,6 @@
 		};
 
 		ldo4_reg: regulator@6 {
-			reg = <6>;
 			/* VDD_3V3A */
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -173,6 +173,8 @@
 
 		sound0_master: simple-audio-card,codec {
 			sound-dai = <&tlv320aic3104>;
+			assigned-clocks = <&clkoutmux2_clk_mux>;
+			assigned-clock-parents = <&sys_clk2_dclk_div>;
 			clocks = <&clkout2_clk>;
 		};
 	};
@@ -796,6 +798,8 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&mcasp3_pins_default>;
 	pinctrl-1 = <&mcasp3_pins_sleep>;
+	assigned-clocks = <&mcasp3_ahclkx_mux>;
+	assigned-clock-parents = <&sys_clkin2>;
 	status = "okay";
 
 	op-mode = <0>;	/* MCASP_IIS_MODE */

arch/arm/boot/dts/am57xx-cl-som-am57x.dts

@@ -545,7 +545,7 @@
 		ti,debounce-tol = /bits/ 16 <10>;
 		ti,debounce-rep = /bits/ 16 <1>;
 
-		linux,wakeup;
+		wakeup-source;
 	};
 };
 

arch/arm/boot/dts/imx6qdl.dtsi

@@ -896,7 +896,6 @@
 				#size-cells = <1>;
 				reg = <0x2100000 0x10000>;
 				ranges = <0 0x2100000 0x10000>;
-				interrupt-parent = <&intc>;
 				clocks = <&clks IMX6QDL_CLK_CAAM_MEM>,
 					 <&clks IMX6QDL_CLK_CAAM_ACLK>,
 					 <&clks IMX6QDL_CLK_CAAM_IPG>,

arch/arm/boot/dts/kirkwood-ds112.dts

@@ -14,7 +14,7 @@
 #include "kirkwood-synology.dtsi"
 
 / {
-	model = "Synology DS111";
+	model = "Synology DS112";
 	compatible = "synology,ds111", "marvell,kirkwood";
 
 	memory {

arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts

@@ -228,6 +228,37 @@
 	};
 };
 
+&devbus_bootcs {
+	status = "okay";
+	devbus,keep-config;
+
+	flash@0 {
+		compatible = "jedec-flash";
+		reg = <0 0x40000>;
+		bank-width = <1>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			header@0 {
+				reg = <0 0x30000>;
+				read-only;
+			};
+
+			uboot@30000 {
+				reg = <0x30000 0xF000>;
+				read-only;
+			};
+
+			uboot_env@3F000 {
+				reg = <0x3F000 0x1000>;
+			};
+		};
+	};
+};
+
 &mdio {
 	status = "okay";
 

arch/arm/boot/dts/sama5d2-pinfunc.h

@@ -90,7 +90,7 @@
 #define PIN_PA14__I2SC1_MCK		PINMUX_PIN(PIN_PA14, 4, 2)
 #define PIN_PA14__FLEXCOM3_IO2		PINMUX_PIN(PIN_PA14, 5, 1)
 #define PIN_PA14__D9			PINMUX_PIN(PIN_PA14, 6, 2)
-#define PIN_PA15			14
+#define PIN_PA15			15
 #define PIN_PA15__GPIO			PINMUX_PIN(PIN_PA15, 0, 0)
 #define PIN_PA15__SPI0_MOSI		PINMUX_PIN(PIN_PA15, 1, 1)
 #define PIN_PA15__TF1			PINMUX_PIN(PIN_PA15, 2, 1)

arch/arm/boot/dts/tps65217.dtsi

@@ -0,0 +1,56 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Integrated Power Management Chip
+ * http://www.ti.com/lit/ds/symlink/tps65217.pdf
+ */
+
+&tps {
+	compatible = "ti,tps65217";
+
+	regulators {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		dcdc1_reg: regulator@0 {
+			reg = <0>;
+			regulator-compatible = "dcdc1";
+		};
+
+		dcdc2_reg: regulator@1 {
+			reg = <1>;
+			regulator-compatible = "dcdc2";
+		};
+
+		dcdc3_reg: regulator@2 {
+			reg = <2>;
+			regulator-compatible = "dcdc3";
+		};
+
+		ldo1_reg: regulator@3 {
+			reg = <3>;
+			regulator-compatible = "ldo1";
+		};
+
+		ldo2_reg: regulator@4 {
+			reg = <4>;
+			regulator-compatible = "ldo2";
+		};
+
+		ldo3_reg: regulator@5 {
+			reg = <5>;
+			regulator-compatible = "ldo3";
+		};
+
+		ldo4_reg: regulator@6 {
+			reg = <6>;
+			regulator-compatible = "ldo4";
+		};
+	};
+};

arch/arm/common/icst.c

@@ -16,7 +16,7 @@
  */
 #include <linux/module.h>
 #include <linux/kernel.h>
-
+#include <asm/div64.h>
 #include <asm/hardware/icst.h>
 
 /*
@@ -29,7 +29,11 @@ EXPORT_SYMBOL(icst525_s2div);
 
 unsigned long icst_hz(const struct icst_params *p, struct icst_vco vco)
 {
-	return p->ref * 2 * (vco.v + 8) / ((vco.r + 2) * p->s2div[vco.s]);
+	u64 dividend = p->ref * 2 * (u64)(vco.v + 8);
+	u32 divisor = (vco.r + 2) * p->s2div[vco.s];
+
+	do_div(dividend, divisor);
+	return (unsigned long)dividend;
 }
 
 EXPORT_SYMBOL(icst_hz);
@@ -58,6 +62,7 @@ icst_hz_to_vco(const struct icst_params *p, unsigned long freq)
 
 		if (f > p->vco_min && f <= p->vco_max)
 			break;
+		i++;
 	} while (i < 8);
 
 	if (i >= 8)

arch/arm/configs/omap2plus_defconfig

@@ -292,24 +292,23 @@ CONFIG_FB=y
 CONFIG_FIRMWARE_EDID=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_FB_TILEBLITTING=y
-CONFIG_OMAP2_DSS=m
-CONFIG_OMAP5_DSS_HDMI=y
-CONFIG_OMAP2_DSS_SDI=y
-CONFIG_OMAP2_DSS_DSI=y
+CONFIG_FB_OMAP5_DSS_HDMI=y
+CONFIG_FB_OMAP2_DSS_SDI=y
+CONFIG_FB_OMAP2_DSS_DSI=y
 CONFIG_FB_OMAP2=m
-CONFIG_DISPLAY_ENCODER_TFP410=m
-CONFIG_DISPLAY_ENCODER_TPD12S015=m
-CONFIG_DISPLAY_CONNECTOR_DVI=m
-CONFIG_DISPLAY_CONNECTOR_HDMI=m
-CONFIG_DISPLAY_CONNECTOR_ANALOG_TV=m
-CONFIG_DISPLAY_PANEL_DPI=m
-CONFIG_DISPLAY_PANEL_DSI_CM=m
-CONFIG_DISPLAY_PANEL_SONY_ACX565AKM=m
-CONFIG_DISPLAY_PANEL_LGPHILIPS_LB035Q02=m
-CONFIG_DISPLAY_PANEL_SHARP_LS037V7DW01=m
-CONFIG_DISPLAY_PANEL_TPO_TD028TTEC1=m
-CONFIG_DISPLAY_PANEL_TPO_TD043MTEA1=m
-CONFIG_DISPLAY_PANEL_NEC_NL8048HL11=m
+CONFIG_FB_OMAP2_ENCODER_TFP410=m
+CONFIG_FB_OMAP2_ENCODER_TPD12S015=m
+CONFIG_FB_OMAP2_CONNECTOR_DVI=m
+CONFIG_FB_OMAP2_CONNECTOR_HDMI=m
+CONFIG_FB_OMAP2_CONNECTOR_ANALOG_TV=m
+CONFIG_FB_OMAP2_PANEL_DPI=m
+CONFIG_FB_OMAP2_PANEL_DSI_CM=m
+CONFIG_FB_OMAP2_PANEL_SONY_ACX565AKM=m
+CONFIG_FB_OMAP2_PANEL_LGPHILIPS_LB035Q02=m
+CONFIG_FB_OMAP2_PANEL_SHARP_LS037V7DW01=m
+CONFIG_FB_OMAP2_PANEL_TPO_TD028TTEC1=m
+CONFIG_FB_OMAP2_PANEL_TPO_TD043MTEA1=m
+CONFIG_FB_OMAP2_PANEL_NEC_NL8048HL11=m
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_LCD_PLATFORM=y

arch/arm/crypto/aes-ce-glue.c

@@ -364,7 +364,7 @@ static struct crypto_alg aes_algs[] = { {
 	.cra_blkcipher = {
 		.min_keysize	= AES_MIN_KEY_SIZE,
 		.max_keysize	= AES_MAX_KEY_SIZE,
-		.ivsize		= AES_BLOCK_SIZE,
+		.ivsize		= 0,
 		.setkey		= ce_aes_setkey,
 		.encrypt	= ecb_encrypt,
 		.decrypt	= ecb_decrypt,
@@ -441,7 +441,7 @@ static struct crypto_alg aes_algs[] = { {
 	.cra_ablkcipher = {
 		.min_keysize	= AES_MIN_KEY_SIZE,
 		.max_keysize	= AES_MAX_KEY_SIZE,
-		.ivsize		= AES_BLOCK_SIZE,
+		.ivsize		= 0,
 		.setkey		= ablk_set_key,
 		.encrypt	= ablk_encrypt,
 		.decrypt	= ablk_decrypt,

arch/arm/include/asm/arch_gicv3.h

@@ -117,6 +117,7 @@ static inline u32 gic_read_iar(void)
 	u32 irqstat;
 
 	asm volatile("mrc " __stringify(ICC_IAR1) : "=r" (irqstat));
+	dsb(sy);
 	return irqstat;
 }
 

arch/arm/include/asm/xen/page-coherent.h

@@ -35,14 +35,21 @@ static inline void xen_dma_map_page(struct device *hwdev, struct page *page,
 	     dma_addr_t dev_addr, unsigned long offset, size_t size,
 	     enum dma_data_direction dir, struct dma_attrs *attrs)
 {
-	bool local = XEN_PFN_DOWN(dev_addr) == page_to_xen_pfn(page);
+	unsigned long page_pfn = page_to_xen_pfn(page);
+	unsigned long dev_pfn = XEN_PFN_DOWN(dev_addr);
+	unsigned long compound_pages =
+		(1<<compound_order(page)) * XEN_PFN_PER_PAGE;
+	bool local = (page_pfn <= dev_pfn) &&
+		(dev_pfn - page_pfn < compound_pages);
+
 	/*
-	 * Dom0 is mapped 1:1, while the Linux page can be spanned accross
-	 * multiple Xen page, it's not possible to have a mix of local and
-	 * foreign Xen page. So if the first xen_pfn == mfn the page is local
-	 * otherwise it's a foreign page grant-mapped in dom0. If the page is
-	 * local we can safely call the native dma_ops function, otherwise we
-	 * call the xen specific function.
+	 * Dom0 is mapped 1:1, while the Linux page can span across
+	 * multiple Xen pages, it's not possible for it to contain a
+	 * mix of local and foreign Xen pages. So if the first xen_pfn
+	 * == mfn the page is local otherwise it's a foreign page
+	 * grant-mapped in dom0. If the page is local we can safely
+	 * call the native dma_ops function, otherwise we call the xen
+	 * specific function.
 	 */
 	if (local)
 		__generic_dma_ops(hwdev)->map_page(hwdev, page, offset, size, dir, attrs);

arch/arm/kvm/mmio.c

@@ -206,7 +206,8 @@ int io_mem_abort(struct kvm_vcpu *vcpu, struct kvm_run *run,
 	run->mmio.is_write	= is_write;
 	run->mmio.phys_addr	= fault_ipa;
 	run->mmio.len		= len;
-	memcpy(run->mmio.data, data_buf, len);
+	if (is_write)
+		memcpy(run->mmio.data, data_buf, len);
 
 	if (!ret) {
 		/* We handled the access successfully in the kernel. */

arch/arm/mach-omap2/board-generic.c

@@ -18,6 +18,7 @@
 
 #include <asm/setup.h>
 #include <asm/mach/arch.h>
+#include <asm/system_info.h>
 
 #include "common.h"
 
@@ -77,12 +78,31 @@ static const char *const n900_boards_compat[] __initconst = {
 	NULL,
 };
 
+/* Set system_rev from atags */
+static void __init rx51_set_system_rev(const struct tag *tags)
+{
+	const struct tag *tag;
+
+	if (tags->hdr.tag != ATAG_CORE)
+		return;
+
+	for_each_tag(tag, tags) {
+		if (tag->hdr.tag == ATAG_REVISION) {
+			system_rev = tag->u.revision.rev;
+			break;
+		}
+	}
+}
+
 /* Legacy userspace on Nokia N900 needs ATAGS exported in /proc/atags,
  * save them while the data is still not overwritten
  */
 static void __init rx51_reserve(void)
 {
-	save_atags((const struct tag *)(PAGE_OFFSET + 0x100));
+	const struct tag *tags = (const struct tag *)(PAGE_OFFSET + 0x100);
+
+	save_atags(tags);
+	rx51_set_system_rev(tags);
 	omap_reserve();
 }
 

arch/arm/mach-omap2/gpmc-onenand.c

@@ -101,10 +101,8 @@ static void omap2_onenand_set_async_mode(void __iomem *onenand_base)
 
 static void set_onenand_cfg(void __iomem *onenand_base)
 {
-	u32 reg;
+	u32 reg = ONENAND_SYS_CFG1_RDY | ONENAND_SYS_CFG1_INT;
 
-	reg = readw(onenand_base + ONENAND_REG_SYS_CFG1);
-	reg &= ~((0x7 << ONENAND_SYS_CFG1_BRL_SHIFT) | (0x7 << 9));
 	reg |=	(latency << ONENAND_SYS_CFG1_BRL_SHIFT) |
 		ONENAND_SYS_CFG1_BL_16;
 	if (onenand_flags & ONENAND_FLAG_SYNCREAD)
@@ -123,6 +121,7 @@ static void set_onenand_cfg(void __iomem *onenand_base)
 		reg |= ONENAND_SYS_CFG1_VHF;
 	else
 		reg &= ~ONENAND_SYS_CFG1_VHF;
+
 	writew(reg, onenand_base + ONENAND_REG_SYS_CFG1);
 }
 
@@ -289,6 +288,7 @@ static int omap2_onenand_setup_async(void __iomem *onenand_base)
 		}
 	}
 
+	onenand_async.sync_write = true;
 	omap2_onenand_calc_async_timings(&t);
 
 	ret = gpmc_cs_program_settings(gpmc_onenand_data->cs, &onenand_async);

arch/arm/mach-omap2/omap_device.c

@@ -191,12 +191,22 @@ static int _omap_device_notifier_call(struct notifier_block *nb,
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct omap_device *od;
+	int err;
 
 	switch (event) {
 	case BUS_NOTIFY_DEL_DEVICE:
 		if (pdev->archdata.od)
 			omap_device_delete(pdev->archdata.od);
 		break;
+	case BUS_NOTIFY_UNBOUND_DRIVER:
+		od = to_omap_device(pdev);
+		if (od && (od->_state == OMAP_DEVICE_STATE_ENABLED)) {
+			dev_info(dev, "enabled after unload, idling\n");
+			err = omap_device_idle(pdev);
+			if (err)
+				dev_err(dev, "failed to idle\n");
+		}
+		break;
 	case BUS_NOTIFY_ADD_DEVICE:
 		if (pdev->dev.of_node)
 			omap_device_build_from_dt(pdev);
@@ -602,8 +612,10 @@ static int _od_runtime_resume(struct device *dev)
 	int ret;
 
 	ret = omap_device_enable(pdev);
-	if (ret)
+	if (ret) {
+		dev_err(dev, "use pm_runtime_put_sync_suspend() in driver?\n");
 		return ret;
+	}
 
 	return pm_generic_runtime_resume(dev);
 }

arch/arm/mach-shmobile/common.h

@@ -4,7 +4,6 @@
 extern void shmobile_init_delay(void);
 extern void shmobile_boot_vector(void);
 extern unsigned long shmobile_boot_fn;
-extern unsigned long shmobile_boot_arg;
 extern unsigned long shmobile_boot_size;
 extern void shmobile_smp_boot(void);
 extern void shmobile_smp_sleep(void);

arch/arm/mach-shmobile/headsmp-scu.S

@@ -38,9 +38,3 @@ ENTRY(shmobile_boot_scu)
 
 	b	secondary_startup
 ENDPROC(shmobile_boot_scu)
-
-	.text
-	.align	2
-	.globl	shmobile_scu_base
-shmobile_scu_base:
-	.space	4

arch/arm/mach-shmobile/headsmp.S

@@ -24,7 +24,6 @@
 	.arm
 	.align  12
 ENTRY(shmobile_boot_vector)
-	ldr     r0, 2f
 	ldr     r1, 1f
 	bx	r1
 
@@ -34,9 +33,6 @@ ENDPROC(shmobile_boot_vector)
 	.globl	shmobile_boot_fn
 shmobile_boot_fn:
 1:	.space	4
-	.globl	shmobile_boot_arg
-shmobile_boot_arg:
-2:	.space	4
 	.globl	shmobile_boot_size
 shmobile_boot_size:
 	.long	. - shmobile_boot_vector
@@ -46,13 +42,15 @@ shmobile_boot_size:
  */
 
 ENTRY(shmobile_smp_boot)
-						@ r0 = MPIDR_HWID_BITMASK
 	mrc	p15, 0, r1, c0, c0, 5		@ r1 = MPIDR
-	and	r0, r1, r0			@ r0 = cpu_logical_map() value
+	and	r0, r1, #0xffffff		@ MPIDR_HWID_BITMASK
+						@ r0 = cpu_logical_map() value
 	mov	r1, #0				@ r1 = CPU index
-	adr	r5, 1f				@ array of per-cpu mpidr values
-	adr	r6, 2f				@ array of per-cpu functions
-	adr	r7, 3f				@ array of per-cpu arguments
+	adr	r2, 1f
+	ldmia	r2, {r5, r6, r7}
+	add	r5, r5, r2			@ array of per-cpu mpidr values
+	add	r6, r6, r2			@ array of per-cpu functions
+	add	r7, r7, r2			@ array of per-cpu arguments
 
 shmobile_smp_boot_find_mpidr:
 	ldr	r8, [r5, r1, lsl #2]
@@ -80,12 +78,18 @@ ENTRY(shmobile_smp_sleep)
 	b	shmobile_smp_boot
 ENDPROC(shmobile_smp_sleep)
 
+	.align	2
+1:	.long	shmobile_smp_mpidr - .
+	.long	shmobile_smp_fn - 1b
+	.long	shmobile_smp_arg - 1b
+
+	.bss
 	.globl	shmobile_smp_mpidr
 shmobile_smp_mpidr:
-1:	.space	NR_CPUS * 4
+	.space	NR_CPUS * 4
 	.globl	shmobile_smp_fn
 shmobile_smp_fn:
-2:	.space	NR_CPUS * 4
+	.space	NR_CPUS * 4
 	.globl	shmobile_smp_arg
 shmobile_smp_arg:
-3:	.space	NR_CPUS * 4
+	.space	NR_CPUS * 4

arch/arm/mach-shmobile/platsmp-apmu.c

@@ -123,7 +123,6 @@ void __init shmobile_smp_apmu_prepare_cpus(unsigned int max_cpus,
 {
 	/* install boot code shared by all CPUs */
 	shmobile_boot_fn = virt_to_phys(shmobile_smp_boot);
-	shmobile_boot_arg = MPIDR_HWID_BITMASK;
 
 	/* perform per-cpu setup */
 	apmu_parse_cfg(apmu_init_cpu, apmu_config, num);

arch/arm/mach-shmobile/platsmp-scu.c

@@ -17,6 +17,9 @@
 #include <asm/smp_scu.h>
 #include "common.h"
 
+
+void __iomem *shmobile_scu_base;
+
 static int shmobile_smp_scu_notifier_call(struct notifier_block *nfb,
 					  unsigned long action, void *hcpu)
 {
@@ -41,7 +44,6 @@ void __init shmobile_smp_scu_prepare_cpus(unsigned int max_cpus)
 {
 	/* install boot code shared by all CPUs */
 	shmobile_boot_fn = virt_to_phys(shmobile_smp_boot);
-	shmobile_boot_arg = MPIDR_HWID_BITMASK;
 
 	/* enable SCU and cache coherency on booting CPU */
 	scu_enable(shmobile_scu_base);

arch/arm/mach-shmobile/smp-r8a7779.c

@@ -92,8 +92,6 @@ static void __init r8a7779_smp_prepare_cpus(unsigned int max_cpus)
 {
 	/* Map the reset vector (in headsmp-scu.S, headsmp.S) */
 	__raw_writel(__pa(shmobile_boot_vector), AVECR);
-	shmobile_boot_fn = virt_to_phys(shmobile_boot_scu);
-	shmobile_boot_arg = (unsigned long)shmobile_scu_base;
 
 	/* setup r8a7779 specific SCU bits */
 	shmobile_scu_base = IOMEM(R8A7779_SCU_BASE);

arch/arm/mm/mmap.c

@@ -173,7 +173,7 @@ unsigned long arch_mmap_rnd(void)
 {
 	unsigned long rnd;
 
-	rnd = (unsigned long)get_random_int() & ((1 << mmap_rnd_bits) - 1);
+	rnd = get_random_long() & ((1UL << mmap_rnd_bits) - 1);
 
 	return rnd << PAGE_SHIFT;
 }

arch/arm64/Makefile

@@ -88,7 +88,7 @@ Image: vmlinux
 Image.%: vmlinux
 	$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
 
-zinstall install: vmlinux
+zinstall install:
 	$(Q)$(MAKE) $(build)=$(boot) $@
 
 %.dtb: scripts

arch/arm64/boot/Makefile

@@ -34,10 +34,10 @@ $(obj)/Image.lzma: $(obj)/Image FORCE
 $(obj)/Image.lzo: $(obj)/Image FORCE
 	$(call if_changed,lzo)
 
-install: $(obj)/Image
+install:
 	$(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
 	$(obj)/Image System.map "$(INSTALL_PATH)"
 
-zinstall: $(obj)/Image.gz
+zinstall:
 	$(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
 	$(obj)/Image.gz System.map "$(INSTALL_PATH)"

arch/arm64/boot/install.sh

@@ -20,6 +20,20 @@
 #   $4 - default install path (blank if root directory)
 #
 
+verify () {
+	if [ ! -f "$1" ]; then
+		echo ""                                                   1>&2
+		echo " *** Missing file: $1"                              1>&2
+		echo ' *** You need to run "make" before "make install".' 1>&2
+		echo ""                                                   1>&2
+		exit 1
+	fi
+}
+
+# Make sure the files actually exist
+verify "$2"
+verify "$3"
+
 # User may have a custom install script
 if [ -x ~/bin/${INSTALLKERNEL} ]; then exec ~/bin/${INSTALLKERNEL} "$@"; fi
 if [ -x /sbin/${INSTALLKERNEL} ]; then exec /sbin/${INSTALLKERNEL} "$@"; fi

arch/arm64/crypto/aes-glue.c

@@ -294,7 +294,7 @@ static struct crypto_alg aes_algs[] = { {
 	.cra_blkcipher = {
 		.min_keysize	= AES_MIN_KEY_SIZE,
 		.max_keysize	= AES_MAX_KEY_SIZE,
-		.ivsize		= AES_BLOCK_SIZE,
+		.ivsize		= 0,
 		.setkey		= aes_setkey,
 		.encrypt	= ecb_encrypt,
 		.decrypt	= ecb_decrypt,
@@ -371,7 +371,7 @@ static struct crypto_alg aes_algs[] = { {
 	.cra_ablkcipher = {
 		.min_keysize	= AES_MIN_KEY_SIZE,
 		.max_keysize	= AES_MAX_KEY_SIZE,
-		.ivsize		= AES_BLOCK_SIZE,
+		.ivsize		= 0,
 		.setkey		= ablk_set_key,
 		.encrypt	= ablk_encrypt,
 		.decrypt	= ablk_decrypt,

arch/arm64/include/asm/arch_gicv3.h

@@ -103,6 +103,7 @@ static inline u64 gic_read_iar_common(void)
 	u64 irqstat;
 
 	asm volatile("mrs_s %0, " __stringify(ICC_IAR1_EL1) : "=r" (irqstat));
+	dsb(sy);
 	return irqstat;
 }
 

arch/arm64/include/asm/kvm_arm.h

@@ -107,8 +107,6 @@
 #define TCR_EL2_MASK	(TCR_EL2_TG0 | TCR_EL2_SH0 | \
 			 TCR_EL2_ORGN0 | TCR_EL2_IRGN0 | TCR_EL2_T0SZ)
 
-#define TCR_EL2_FLAGS	(TCR_EL2_RES1 | TCR_EL2_PS_40B)
-
 /* VTCR_EL2 Registers bits */
 #define VTCR_EL2_RES1		(1 << 31)
 #define VTCR_EL2_PS_MASK	(7 << 16)
@@ -182,6 +180,7 @@
 #define CPTR_EL2_TCPAC	(1 << 31)
 #define CPTR_EL2_TTA	(1 << 20)
 #define CPTR_EL2_TFP	(1 << CPTR_EL2_TFP_SHIFT)
+#define CPTR_EL2_DEFAULT	0x000033ff
 
 /* Hyp Debug Configuration Register bits */
 #define MDCR_EL2_TDRA		(1 << 11)

arch/arm64/include/asm/kvm_emulate.h

@@ -127,10 +127,14 @@ static inline unsigned long *vcpu_spsr(const struct kvm_vcpu *vcpu)
 
 static inline bool vcpu_mode_priv(const struct kvm_vcpu *vcpu)
 {
-	u32 mode = *vcpu_cpsr(vcpu) & PSR_MODE_MASK;
+	u32 mode;
 
-	if (vcpu_mode_is_32bit(vcpu))
+	if (vcpu_mode_is_32bit(vcpu)) {
+		mode = *vcpu_cpsr(vcpu) & COMPAT_PSR_MODE_MASK;
 		return mode > COMPAT_PSR_MODE_USR;
+	}
+
+	mode = *vcpu_cpsr(vcpu) & PSR_MODE_MASK;
 
 	return mode != PSR_MODE_EL0t;
 }

arch/arm64/kernel/debug-monitors.c

@@ -226,11 +226,28 @@ static int call_step_hook(struct pt_regs *regs, unsigned int esr)
 	return retval;
 }
 
+static void send_user_sigtrap(int si_code)
+{
+	struct pt_regs *regs = current_pt_regs();
+	siginfo_t info = {
+		.si_signo	= SIGTRAP,
+		.si_errno	= 0,
+		.si_code	= si_code,
+		.si_addr	= (void __user *)instruction_pointer(regs),
+	};
+
+	if (WARN_ON(!user_mode(regs)))
+		return;
+
+	if (interrupts_enabled(regs))
+		local_irq_enable();
+
+	force_sig_info(SIGTRAP, &info, current);
+}
+
 static int single_step_handler(unsigned long addr, unsigned int esr,
 			       struct pt_regs *regs)
 {
-	siginfo_t info;
-
 	/*
 	 * If we are stepping a pending breakpoint, call the hw_breakpoint
 	 * handler first.
@@ -239,11 +256,7 @@ static int single_step_handler(unsigned long addr, unsigned int esr,
 		return 0;
 
 	if (user_mode(regs)) {
-		info.si_signo = SIGTRAP;
-		info.si_errno = 0;
-		info.si_code  = TRAP_HWBKPT;
-		info.si_addr  = (void __user *)instruction_pointer(regs);
-		force_sig_info(SIGTRAP, &info, current);
+		send_user_sigtrap(TRAP_HWBKPT);
 
 		/*
 		 * ptrace will disable single step unless explicitly
@@ -307,17 +320,8 @@ static int call_break_hook(struct pt_regs *regs, unsigned int esr)
 static int brk_handler(unsigned long addr, unsigned int esr,
 		       struct pt_regs *regs)
 {
-	siginfo_t info;
-
 	if (user_mode(regs)) {
-		info = (siginfo_t) {
-			.si_signo = SIGTRAP,
-			.si_errno = 0,
-			.si_code  = TRAP_BRKPT,
-			.si_addr  = (void __user *)instruction_pointer(regs),
-		};
-
-		force_sig_info(SIGTRAP, &info, current);
+		send_user_sigtrap(TRAP_BRKPT);
 	} else if (call_break_hook(regs, esr) != DBG_HOOK_HANDLED) {
 		pr_warning("Unexpected kernel BRK exception at EL1\n");
 		return -EFAULT;
@@ -328,7 +332,6 @@ static int brk_handler(unsigned long addr, unsigned int esr,
 
 int aarch32_break_handler(struct pt_regs *regs)
 {
-	siginfo_t info;
 	u32 arm_instr;
 	u16 thumb_instr;
 	bool bp = false;
@@ -359,14 +362,7 @@ int aarch32_break_handler(struct pt_regs *regs)
 	if (!bp)
 		return -EFAULT;
 
-	info = (siginfo_t) {
-		.si_signo = SIGTRAP,
-		.si_errno = 0,
-		.si_code  = TRAP_BRKPT,
-		.si_addr  = pc,
-	};
-
-	force_sig_info(SIGTRAP, &info, current);
+	send_user_sigtrap(TRAP_BRKPT);
 	return 0;
 }
 

arch/arm64/kernel/image.h

@@ -89,6 +89,7 @@ __efistub_memcpy		= KALLSYMS_HIDE(__pi_memcpy);
 __efistub_memmove		= KALLSYMS_HIDE(__pi_memmove);
 __efistub_memset		= KALLSYMS_HIDE(__pi_memset);
 __efistub_strlen		= KALLSYMS_HIDE(__pi_strlen);
+__efistub_strnlen		= KALLSYMS_HIDE(__pi_strnlen);
 __efistub_strcmp		= KALLSYMS_HIDE(__pi_strcmp);
 __efistub_strncmp		= KALLSYMS_HIDE(__pi_strncmp);
 __efistub___flush_dcache_area	= KALLSYMS_HIDE(__pi___flush_dcache_area);

arch/arm64/kernel/stacktrace.c

@@ -44,14 +44,13 @@ int notrace unwind_frame(struct task_struct *tsk, struct stackframe *frame)
 	unsigned long irq_stack_ptr;
 
 	/*
-	 * Use raw_smp_processor_id() to avoid false-positives from
-	 * CONFIG_DEBUG_PREEMPT. get_wchan() calls unwind_frame() on sleeping
-	 * task stacks, we can be pre-empted in this case, so
-	 * {raw_,}smp_processor_id() may give us the wrong value. Sleeping
-	 * tasks can't ever be on an interrupt stack, so regardless of cpu,
-	 * the checks will always fail.
+	 * Switching between stacks is valid when tracing current and in
+	 * non-preemptible context.
 	 */
-	irq_stack_ptr = IRQ_STACK_PTR(raw_smp_processor_id());
+	if (tsk == current && !preemptible())
+		irq_stack_ptr = IRQ_STACK_PTR(smp_processor_id());
+	else
+		irq_stack_ptr = 0;
 
 	low  = frame->sp;
 	/* irq stacks are not THREAD_SIZE aligned */
@@ -64,8 +63,8 @@ int notrace unwind_frame(struct task_struct *tsk, struct stackframe *frame)
 		return -EINVAL;
 
 	frame->sp = fp + 0x10;
-	frame->fp = *(unsigned long *)(fp);
-	frame->pc = *(unsigned long *)(fp + 8);
+	frame->fp = READ_ONCE_NOCHECK(*(unsigned long *)(fp));
+	frame->pc = READ_ONCE_NOCHECK(*(unsigned long *)(fp + 8));
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 	if (tsk && tsk->ret_stack &&

arch/arm64/kernel/traps.c

@@ -146,9 +146,18 @@ static void dump_instr(const char *lvl, struct pt_regs *regs)
 static void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk)
 {
 	struct stackframe frame;
-	unsigned long irq_stack_ptr = IRQ_STACK_PTR(smp_processor_id());
+	unsigned long irq_stack_ptr;
 	int skip;
 
+	/*
+	 * Switching between stacks is valid when tracing current and in
+	 * non-preemptible context.
+	 */
+	if (tsk == current && !preemptible())
+		irq_stack_ptr = IRQ_STACK_PTR(smp_processor_id());
+	else
+		irq_stack_ptr = 0;
+
 	pr_debug("%s(regs = %p tsk = %p)\n", __func__, regs, tsk);
 
 	if (!tsk)

arch/arm64/kvm/hyp-init.S

@@ -64,7 +64,7 @@ __do_hyp_init:
 	mrs	x4, tcr_el1
 	ldr	x5, =TCR_EL2_MASK
 	and	x4, x4, x5
-	ldr	x5, =TCR_EL2_FLAGS
+	mov	x5, #TCR_EL2_RES1
 	orr	x4, x4, x5
 
 #ifndef CONFIG_ARM64_VA_BITS_48
@@ -85,15 +85,17 @@ __do_hyp_init:
 	ldr_l	x5, idmap_t0sz
 	bfi	x4, x5, TCR_T0SZ_OFFSET, TCR_TxSZ_WIDTH
 #endif
-	msr	tcr_el2, x4
-
-	ldr	x4, =VTCR_EL2_FLAGS
 	/*
 	 * Read the PARange bits from ID_AA64MMFR0_EL1 and set the PS bits in
-	 * VTCR_EL2.
+	 * TCR_EL2 and VTCR_EL2.
 	 */
 	mrs	x5, ID_AA64MMFR0_EL1
 	bfi	x4, x5, #16, #3
+
+	msr	tcr_el2, x4
+
+	ldr	x4, =VTCR_EL2_FLAGS
+	bfi	x4, x5, #16, #3
 	/*
 	 * Read the VMIDBits bits from ID_AA64MMFR1_EL1 and set the VS bit in
 	 * VTCR_EL2.

arch/arm64/kvm/hyp/switch.c

@@ -36,7 +36,11 @@ static void __hyp_text __activate_traps(struct kvm_vcpu *vcpu)
 	write_sysreg(val, hcr_el2);
 	/* Trap on AArch32 cp15 c15 accesses (EL1 or EL0) */
 	write_sysreg(1 << 15, hstr_el2);
-	write_sysreg(CPTR_EL2_TTA | CPTR_EL2_TFP, cptr_el2);
+
+	val = CPTR_EL2_DEFAULT;
+	val |= CPTR_EL2_TTA | CPTR_EL2_TFP;
+	write_sysreg(val, cptr_el2);
+
 	write_sysreg(vcpu->arch.mdcr_el2, mdcr_el2);
 }
 
@@ -45,7 +49,7 @@ static void __hyp_text __deactivate_traps(struct kvm_vcpu *vcpu)
 	write_sysreg(HCR_RW, hcr_el2);
 	write_sysreg(0, hstr_el2);
 	write_sysreg(read_sysreg(mdcr_el2) & MDCR_EL2_HPMN_MASK, mdcr_el2);
-	write_sysreg(0, cptr_el2);
+	write_sysreg(CPTR_EL2_DEFAULT, cptr_el2);
 }
 
 static void __hyp_text __activate_vm(struct kvm_vcpu *vcpu)

arch/arm64/kvm/hyp/vgic-v3-sr.c

@@ -147,16 +147,6 @@ void __hyp_text __vgic_v3_restore_state(struct kvm_vcpu *vcpu)
 	max_lr_idx = vtr_to_max_lr_idx(val);
 	nr_pri_bits = vtr_to_nr_pri_bits(val);
 
-	switch (nr_pri_bits) {
-	case 7:
-		 write_gicreg(cpu_if->vgic_ap1r[3], ICH_AP1R3_EL2);
-		 write_gicreg(cpu_if->vgic_ap1r[2], ICH_AP1R2_EL2);
-	case 6:
-		 write_gicreg(cpu_if->vgic_ap1r[1], ICH_AP1R1_EL2);
-	default:
-		 write_gicreg(cpu_if->vgic_ap1r[0], ICH_AP1R0_EL2);
-	}	 	                           
-		 	                           
 	switch (nr_pri_bits) {
 	case 7:
 		 write_gicreg(cpu_if->vgic_ap0r[3], ICH_AP0R3_EL2);
@@ -167,6 +157,16 @@ void __hyp_text __vgic_v3_restore_state(struct kvm_vcpu *vcpu)
 		 write_gicreg(cpu_if->vgic_ap0r[0], ICH_AP0R0_EL2);
 	}
 
+	switch (nr_pri_bits) {
+	case 7:
+		 write_gicreg(cpu_if->vgic_ap1r[3], ICH_AP1R3_EL2);
+		 write_gicreg(cpu_if->vgic_ap1r[2], ICH_AP1R2_EL2);
+	case 6:
+		 write_gicreg(cpu_if->vgic_ap1r[1], ICH_AP1R1_EL2);
+	default:
+		 write_gicreg(cpu_if->vgic_ap1r[0], ICH_AP1R0_EL2);
+	}
+
 	switch (max_lr_idx) {
 	case 15:
 		write_gicreg(cpu_if->vgic_lr[VGIC_V3_LR_INDEX(15)], ICH_LR15_EL2);

arch/arm64/kvm/inject_fault.c

@@ -27,7 +27,11 @@
 
 #define PSTATE_FAULT_BITS_64 	(PSR_MODE_EL1h | PSR_A_BIT | PSR_F_BIT | \
 				 PSR_I_BIT | PSR_D_BIT)
-#define EL1_EXCEPT_SYNC_OFFSET	0x200
+
+#define CURRENT_EL_SP_EL0_VECTOR	0x0
+#define CURRENT_EL_SP_ELx_VECTOR	0x200
+#define LOWER_EL_AArch64_VECTOR		0x400
+#define LOWER_EL_AArch32_VECTOR		0x600
 
 static void prepare_fault32(struct kvm_vcpu *vcpu, u32 mode, u32 vect_offset)
 {
@@ -97,6 +101,34 @@ static void inject_abt32(struct kvm_vcpu *vcpu, bool is_pabt,
 		*fsr = 0x14;
 }
 
+enum exception_type {
+	except_type_sync	= 0,
+	except_type_irq		= 0x80,
+	except_type_fiq		= 0x100,
+	except_type_serror	= 0x180,
+};
+
+static u64 get_except_vector(struct kvm_vcpu *vcpu, enum exception_type type)
+{
+	u64 exc_offset;
+
+	switch (*vcpu_cpsr(vcpu) & (PSR_MODE_MASK | PSR_MODE32_BIT)) {
+	case PSR_MODE_EL1t:
+		exc_offset = CURRENT_EL_SP_EL0_VECTOR;
+		break;
+	case PSR_MODE_EL1h:
+		exc_offset = CURRENT_EL_SP_ELx_VECTOR;
+		break;
+	case PSR_MODE_EL0t:
+		exc_offset = LOWER_EL_AArch64_VECTOR;
+		break;
+	default:
+		exc_offset = LOWER_EL_AArch32_VECTOR;
+	}
+
+	return vcpu_sys_reg(vcpu, VBAR_EL1) + exc_offset + type;
+}
+
 static void inject_abt64(struct kvm_vcpu *vcpu, bool is_iabt, unsigned long addr)
 {
 	unsigned long cpsr = *vcpu_cpsr(vcpu);
@@ -108,8 +140,8 @@ static void inject_abt64(struct kvm_vcpu *vcpu, bool is_iabt, unsigned long addr
 	*vcpu_spsr(vcpu) = cpsr;
 	*vcpu_elr_el1(vcpu) = *vcpu_pc(vcpu);
 
+	*vcpu_pc(vcpu) = get_except_vector(vcpu, except_type_sync);
 	*vcpu_cpsr(vcpu) = PSTATE_FAULT_BITS_64;
-	*vcpu_pc(vcpu) = vcpu_sys_reg(vcpu, VBAR_EL1) + EL1_EXCEPT_SYNC_OFFSET;
 
 	vcpu_sys_reg(vcpu, FAR_EL1) = addr;
 
@@ -143,8 +175,8 @@ static void inject_undef64(struct kvm_vcpu *vcpu)
 	*vcpu_spsr(vcpu) = cpsr;
 	*vcpu_elr_el1(vcpu) = *vcpu_pc(vcpu);
 
+	*vcpu_pc(vcpu) = get_except_vector(vcpu, except_type_sync);
 	*vcpu_cpsr(vcpu) = PSTATE_FAULT_BITS_64;
-	*vcpu_pc(vcpu) = vcpu_sys_reg(vcpu, VBAR_EL1) + EL1_EXCEPT_SYNC_OFFSET;
 
 	/*
 	 * Build an unknown exception, depending on the instruction

arch/arm64/kvm/sys_regs.c

@@ -1007,10 +1007,9 @@ static int emulate_cp(struct kvm_vcpu *vcpu,
 		if (likely(r->access(vcpu, params, r))) {
 			/* Skip instruction, since it was emulated */
 			kvm_skip_instr(vcpu, kvm_vcpu_trap_il_is32bit(vcpu));
+			/* Handled */
+			return 0;
 		}
-
-		/* Handled */
-		return 0;
 	}
 
 	/* Not handled */
@@ -1043,7 +1042,7 @@ static void unhandled_cp_access(struct kvm_vcpu *vcpu,
 }
 
 /**
- * kvm_handle_cp_64 -- handles a mrrc/mcrr trap on a guest CP15 access
+ * kvm_handle_cp_64 -- handles a mrrc/mcrr trap on a guest CP14/CP15 access
  * @vcpu: The VCPU pointer
  * @run:  The kvm_run struct
  */
@@ -1095,7 +1094,7 @@ out:
 }
 
 /**
- * kvm_handle_cp15_32 -- handles a mrc/mcr trap on a guest CP15 access
+ * kvm_handle_cp_32 -- handles a mrc/mcr trap on a guest CP14/CP15 access
  * @vcpu: The VCPU pointer
  * @run:  The kvm_run struct
  */

arch/arm64/lib/strnlen.S

@@ -168,4 +168,4 @@ CPU_LE( lsr	tmp2, tmp2, tmp4 )	/* Shift (tmp1 & 63).  */
 .Lhit_limit:
 	mov	len, limit
 	ret
-ENDPROC(strnlen)
+ENDPIPROC(strnlen)

arch/arm64/mm/dma-mapping.c

@@ -933,6 +933,10 @@ static int __init __iommu_dma_init(void)
 		ret = register_iommu_dma_ops_notifier(&platform_bus_type);
 	if (!ret)
 		ret = register_iommu_dma_ops_notifier(&amba_bustype);
+
+	/* handle devices queued before this arch_initcall */
+	if (!ret)
+		__iommu_attach_notifier(NULL, BUS_NOTIFY_ADD_DEVICE, NULL);
 	return ret;
 }
 arch_initcall(__iommu_dma_init);

arch/arm64/mm/fault.c

@@ -371,6 +371,13 @@ static int __kprobes do_translation_fault(unsigned long addr,
 	return 0;
 }
 
+static int do_alignment_fault(unsigned long addr, unsigned int esr,
+			      struct pt_regs *regs)
+{
+	do_bad_area(addr, esr, regs);
+	return 0;
+}
+
 /*
  * This abort handler always returns "fault".
  */
@@ -418,7 +425,7 @@ static struct fault_info {
 	{ do_bad,		SIGBUS,  0,		"synchronous parity error (translation table walk)" },
 	{ do_bad,		SIGBUS,  0,		"synchronous parity error (translation table walk)" },
 	{ do_bad,		SIGBUS,  0,		"unknown 32"			},
-	{ do_bad,		SIGBUS,  BUS_ADRALN,	"alignment fault"		},
+	{ do_alignment_fault,	SIGBUS,  BUS_ADRALN,	"alignment fault"		},
 	{ do_bad,		SIGBUS,  0,		"unknown 34"			},
 	{ do_bad,		SIGBUS,  0,		"unknown 35"			},
 	{ do_bad,		SIGBUS,  0,		"unknown 36"			},

arch/arm64/mm/mmap.c

@@ -53,10 +53,10 @@ unsigned long arch_mmap_rnd(void)
 
 #ifdef CONFIG_COMPAT
 	if (test_thread_flag(TIF_32BIT))
-		rnd = (unsigned long)get_random_int() & ((1 << mmap_rnd_compat_bits) - 1);
+		rnd = get_random_long() & ((1UL << mmap_rnd_compat_bits) - 1);
 	else
 #endif
-		rnd = (unsigned long)get_random_int() & ((1 << mmap_rnd_bits) - 1);
+		rnd = get_random_long() & ((1UL << mmap_rnd_bits) - 1);
 	return rnd << PAGE_SHIFT;
 }
 

arch/m68k/configs/amiga_defconfig

@@ -108,6 +108,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -266,6 +268,12 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_ATALK=m
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -366,6 +374,7 @@ CONFIG_ARIADNE=y
 # CONFIG_NET_VENDOR_INTEL is not set
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
 CONFIG_HYDRA=y
 CONFIG_APNE=y
 CONFIG_ZORRO8390=y

arch/m68k/configs/apollo_defconfig

@@ -106,6 +106,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -264,6 +266,12 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_ATALK=m
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -344,6 +352,7 @@ CONFIG_VETH=m
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 # CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set
 # CONFIG_NET_VENDOR_ROCKER is not set

arch/m68k/configs/atari_defconfig

@@ -106,6 +106,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -264,6 +266,12 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_ATALK=m
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -353,6 +361,7 @@ CONFIG_ATARILANCE=y
 # CONFIG_NET_VENDOR_INTEL is not set
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
 CONFIG_NE2000=y
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set

arch/m68k/configs/bvme6000_defconfig

@@ -104,6 +104,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -262,6 +264,12 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_ATALK=m
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -343,6 +351,7 @@ CONFIG_BVME6000_NET=y
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 # CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set
 # CONFIG_NET_VENDOR_ROCKER is not set

arch/m68k/configs/hp300_defconfig

@@ -106,6 +106,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -264,6 +266,12 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_ATALK=m
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -345,6 +353,7 @@ CONFIG_HPLANCE=y
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 # CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set
 # CONFIG_NET_VENDOR_ROCKER is not set

arch/m68k/configs/mac_defconfig

@@ -105,6 +105,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -266,6 +268,12 @@ CONFIG_DEV_APPLETALK=m
 CONFIG_IPDDP=m
 CONFIG_IPDDP_ENCAP=y
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -362,6 +370,7 @@ CONFIG_MAC89x0=y
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 CONFIG_MACSONIC=y
+# CONFIG_NET_VENDOR_NETRONOME is not set
 CONFIG_MAC8390=y
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set

arch/m68k/configs/multi_defconfig

@@ -115,6 +115,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -276,6 +278,12 @@ CONFIG_DEV_APPLETALK=m
 CONFIG_IPDDP=m
 CONFIG_IPDDP_ENCAP=y
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -404,6 +412,7 @@ CONFIG_MVME16x_NET=y
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 CONFIG_MACSONIC=y
+# CONFIG_NET_VENDOR_NETRONOME is not set
 CONFIG_HYDRA=y
 CONFIG_MAC8390=y
 CONFIG_NE2000=y

arch/m68k/configs/mvme147_defconfig

@@ -103,6 +103,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -261,6 +263,12 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_ATALK=m
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -343,6 +351,7 @@ CONFIG_MVME147_NET=y
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 # CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set
 # CONFIG_NET_VENDOR_ROCKER is not set

arch/m68k/configs/mvme16x_defconfig

@@ -104,6 +104,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -262,6 +264,12 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_ATALK=m
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -343,6 +351,7 @@ CONFIG_MVME16x_NET=y
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 # CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set
 # CONFIG_NET_VENDOR_ROCKER is not set

arch/m68k/configs/q40_defconfig

@@ -104,6 +104,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -262,6 +264,12 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_ATALK=m
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -352,6 +360,7 @@ CONFIG_VETH=m
 # CONFIG_NET_VENDOR_INTEL is not set
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
 CONFIG_NE2000=y
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set

arch/m68k/configs/sun3_defconfig

@@ -101,6 +101,8 @@ CONFIG_NFT_NAT=m
 CONFIG_NFT_QUEUE=m
 CONFIG_NFT_REJECT=m
 CONFIG_NFT_COMPAT=m
+CONFIG_NFT_DUP_NETDEV=m
+CONFIG_NFT_FWD_NETDEV=m
 CONFIG_NETFILTER_XT_SET=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
@@ -259,6 +261,12 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_ATALK=m
 CONFIG_6LOWPAN=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP=m
+CONFIG_6LOWPAN_GHC_UDP=m
+CONFIG_6LOWPAN_GHC_ICMPV6=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG=m
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE=m
 CONFIG_DNS_RESOLVER=y
 CONFIG_BATMAN_ADV=m
 CONFIG_BATMAN_ADV_DAT=y
@@ -340,6 +348,7 @@ CONFIG_SUN3_82586=y
 # CONFIG_NET_VENDOR_MARVELL is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 # CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set
 # CONFIG_NET_VENDOR_ROCKER is not set