thermal: exynos: Add support for many TRIMINFO_CTRL registers

This patch support many TRIMINFO_CTRL registers if specific Exynos SoC
has one more TRIMINFO_CTRL registers. Also this patch uses proper 'RELOAD'
shift/mask bit operation to set RELOAD feature instead of static value.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

drivers/thermal/samsung/exynos_thermal_common.h

@@ -27,6 +27,7 @@
 #define SENSOR_NAME_LEN	16
 #define MAX_TRIP_COUNT	8
 #define MAX_COOLING_DEVICE 4
+#define MAX_TRIMINFO_CTRL_REG	2
 
 #define ACTIVE_INTERVAL 500
 #define IDLE_INTERVAL 10000

drivers/thermal/samsung/exynos_tmu.c

@@ -127,7 +127,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
 	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
 	struct exynos_tmu_platform_data *pdata = data->pdata;
 	const struct exynos_tmu_registers *reg = pdata->registers;
-	unsigned int status, trim_info = 0, con;
+	unsigned int status, trim_info = 0, con, ctrl;
 	unsigned int rising_threshold = 0, falling_threshold = 0;
 	int ret = 0, threshold_code, i;
 
@@ -144,8 +144,17 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
 		}
 	}
 
-	if (TMU_SUPPORTS(pdata, TRIM_RELOAD))
-		__raw_writel(1, data->base + reg->triminfo_ctrl);
+	if (TMU_SUPPORTS(pdata, TRIM_RELOAD)) {
+		for (i = 0; i < reg->triminfo_ctrl_count; i++) {
+			if (pdata->triminfo_reload[i]) {
+				ctrl = readl(data->base +
+						reg->triminfo_ctrl[i]);
+				ctrl |= pdata->triminfo_reload[i];
+				writel(ctrl, data->base +
+						reg->triminfo_ctrl[i]);
+			}
+		}
+	}
 
 	/* Save trimming info in order to perform calibration */
 	if (data->soc == SOC_ARCH_EXYNOS5440) {

drivers/thermal/samsung/exynos_tmu.h

@@ -78,6 +78,7 @@ enum soc_type {
  * slightly across different exynos SOC's.
  * @triminfo_data: register containing 2 pont trimming data
  * @triminfo_ctrl: trim info controller register.
+ * @triminfo_ctrl_count: the number of trim info controller register.
  * @tmu_ctrl: TMU main controller register.
  * @test_mux_addr_shift: shift bits of test mux address.
  * @therm_trip_mode_shift: shift bits of tripping mode in tmu_ctrl register.
@@ -112,8 +113,8 @@ enum soc_type {
 struct exynos_tmu_registers {
 	u32	triminfo_data;
 
-	u32	triminfo_ctrl;
-	u32	triminfo_ctrl1;
+	u32	triminfo_ctrl[MAX_TRIMINFO_CTRL_REG];
+	u32	triminfo_ctrl_count;
 
 	u32	tmu_ctrl;
 	u32     test_mux_addr_shift;
@@ -200,6 +201,7 @@ struct exynos_tmu_registers {
  * @second_point_trim: temp value of the second point trimming
  * @default_temp_offset: default temperature offset in case of no trimming
  * @test_mux; information if SoC supports test MUX
+ * @triminfo_reload: reload value to read TRIMINFO register
  * @cal_type: calibration type for temperature
  * @freq_clip_table: Table representing frequency reduction percentage.
  * @freq_tab_count: Count of the above table as frequency reduction may
@@ -230,6 +232,7 @@ struct exynos_tmu_platform_data {
 	u8 second_point_trim;
 	u8 default_temp_offset;
 	u8 test_mux;
+	u8 triminfo_reload[MAX_TRIMINFO_CTRL_REG];
 
 	enum calibration_type cal_type;
 	enum soc_type type;

drivers/thermal/samsung/exynos_tmu_data.c

@@ -169,7 +169,8 @@ struct exynos_tmu_init_data const exynos3250_default_tmu_data = {
 #if defined(CONFIG_SOC_EXYNOS4412) || defined(CONFIG_SOC_EXYNOS5250)
 static const struct exynos_tmu_registers exynos4412_tmu_registers = {
 	.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
-	.triminfo_ctrl = EXYNOS_TMU_TRIMINFO_CON,
+	.triminfo_ctrl[0] = EXYNOS_TMU_TRIMINFO_CON,
+	.triminfo_ctrl_count = 1,
 	.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
 	.test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT,
 	.therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
@@ -231,6 +232,7 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = {
 		.temp_level = 95, \
 	}, \
 	.freq_tab_count = 2, \
+	.triminfo_reload[0] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \
 	.registers = &exynos4412_tmu_registers, \
 	.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \
 			TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \

drivers/thermal/samsung/exynos_tmu_data.h

@@ -51,6 +51,7 @@
 #define EXYNOS_THD_TEMP_FALL		0x54
 #define EXYNOS_EMUL_CON		0x80
 
+#define EXYNOS_TRIMINFO_RELOAD_ENABLE	1
 #define EXYNOS_TRIMINFO_25_SHIFT	0
 #define EXYNOS_TRIMINFO_85_SHIFT	8
 #define EXYNOS_TMU_RISE_INT_MASK	0x111