ARM: OMAP2+: Remove board file for H4

The old 2420 based H4 is probably not used at all as 2420
was Nokia specific SoC. I have one, but I'm not using it because
of it's large size, and I doubt anybody else is using it either.

We do have minimal omap2420-h4.dts in place, so if anybody wants
more support on H4, patches are welcome.

So let's just remove it as that helps us making mach-omap2 to
be device tree only.

Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/mach-omap2/Kconfig

@@ -192,13 +192,6 @@ config MACH_OMAP2_TUSB6010
 	depends on ARCH_OMAP2 && SOC_OMAP2420
 	default y if MACH_NOKIA_N8X0
 
-config MACH_OMAP_H4
-	bool "OMAP 2420 H4 board"
-	depends on SOC_OMAP2420
-	default y
-	select OMAP_DEBUG_DEVICES
-	select OMAP_PACKAGE_ZAF
-
 config MACH_OMAP_2430SDP
 	bool "OMAP 2430 SDP board"
 	depends on SOC_OMAP2430

arch/arm/mach-omap2/Makefile

@@ -237,7 +237,6 @@ obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
 
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
-obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o
 obj-$(CONFIG_MACH_OMAP_2430SDP)		+= board-2430sdp.o
 obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o
 obj-$(CONFIG_MACH_DEVKIT8000)     	+= board-devkit8000.o

arch/arm/mach-omap2/board-h4.c

@@ -1,365 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-h4.c
- *
- * Copyright (C) 2005 Nokia Corporation
- * Author: Paul Mundt <paul.mundt@nokia.com>
- *
- * Modified from mach-omap/omap1/board-generic.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/delay.h>
-#include <linux/workqueue.h>
-#include <linux/i2c.h>
-#include <linux/platform_data/at24.h>
-#include <linux/input.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/mfd/menelaus.h>
-#include <linux/omap-dma.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include "common.h"
-#include "mux.h"
-#include "control.h"
-#include "gpmc.h"
-#include "gpmc-smc91x.h"
-
-#define H4_FLASH_CS	0
-
-#if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE)
-static const uint32_t board_matrix_keys[] = {
-	KEY(0, 0, KEY_LEFT),
-	KEY(1, 0, KEY_RIGHT),
-	KEY(2, 0, KEY_A),
-	KEY(3, 0, KEY_B),
-	KEY(4, 0, KEY_C),
-	KEY(0, 1, KEY_DOWN),
-	KEY(1, 1, KEY_UP),
-	KEY(2, 1, KEY_E),
-	KEY(3, 1, KEY_F),
-	KEY(4, 1, KEY_G),
-	KEY(0, 2, KEY_ENTER),
-	KEY(1, 2, KEY_I),
-	KEY(2, 2, KEY_J),
-	KEY(3, 2, KEY_K),
-	KEY(4, 2, KEY_3),
-	KEY(0, 3, KEY_M),
-	KEY(1, 3, KEY_N),
-	KEY(2, 3, KEY_O),
-	KEY(3, 3, KEY_P),
-	KEY(4, 3, KEY_Q),
-	KEY(0, 4, KEY_R),
-	KEY(1, 4, KEY_4),
-	KEY(2, 4, KEY_T),
-	KEY(3, 4, KEY_U),
-	KEY(4, 4, KEY_ENTER),
-	KEY(0, 5, KEY_V),
-	KEY(1, 5, KEY_W),
-	KEY(2, 5, KEY_L),
-	KEY(3, 5, KEY_S),
-	KEY(4, 5, KEY_ENTER),
-};
-
-static const struct matrix_keymap_data board_keymap_data = {
-	.keymap			= board_matrix_keys,
-	.keymap_size		= ARRAY_SIZE(board_matrix_keys),
-};
-
-static unsigned int board_keypad_row_gpios[] = {
-	88, 89, 124, 11, 6, 96
-};
-
-static unsigned int board_keypad_col_gpios[] = {
-	90, 91, 100, 36, 12, 97, 98
-};
-
-static struct matrix_keypad_platform_data board_keypad_platform_data = {
-	.keymap_data	= &board_keymap_data,
-	.row_gpios	= board_keypad_row_gpios,
-	.num_row_gpios	= ARRAY_SIZE(board_keypad_row_gpios),
-	.col_gpios	= board_keypad_col_gpios,
-	.num_col_gpios	= ARRAY_SIZE(board_keypad_col_gpios),
-	.active_low	= 1,
-
-	.debounce_ms		= 20,
-	.col_scan_delay_us	= 5,
-};
-
-static struct platform_device board_keyboard = {
-	.name	= "matrix-keypad",
-	.id	= -1,
-	.dev	= {
-		.platform_data = &board_keypad_platform_data,
-	},
-};
-static void __init board_mkp_init(void)
-{
-	omap_mux_init_gpio(88, OMAP_PULL_ENA | OMAP_PULL_UP);
-	omap_mux_init_gpio(89, OMAP_PULL_ENA | OMAP_PULL_UP);
-	omap_mux_init_gpio(124, OMAP_PULL_ENA | OMAP_PULL_UP);
-	omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
-	if (omap_has_menelaus()) {
-		omap_mux_init_signal("sdrc_a14.gpio0",
-			OMAP_PULL_ENA | OMAP_PULL_UP);
-		omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
-		omap_mux_init_signal("gpio_98", 0);
-		board_keypad_row_gpios[5] = 0;
-		board_keypad_col_gpios[2] = 15;
-		board_keypad_col_gpios[6] = 18;
-	} else {
-		omap_mux_init_signal("gpio_96", OMAP_PULL_ENA | OMAP_PULL_UP);
-		omap_mux_init_signal("gpio_100", 0);
-		omap_mux_init_signal("gpio_98", 0);
-	}
-	omap_mux_init_signal("gpio_90", 0);
-	omap_mux_init_signal("gpio_91", 0);
-	omap_mux_init_signal("gpio_36", 0);
-	omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0);
-	omap_mux_init_signal("gpio_97", 0);
-
-	platform_device_register(&board_keyboard);
-}
-#else
-static inline void board_mkp_init(void)
-{
-}
-#endif
-
-static struct mtd_partition h4_partitions[] = {
-	/* bootloader (U-Boot, etc) in first sector */
-	{
-	      .name		= "bootloader",
-	      .offset		= 0,
-	      .size		= SZ_128K,
-	      .mask_flags	= MTD_WRITEABLE, /* force read-only */
-	},
-	/* bootloader params in the next sector */
-	{
-	      .name		= "params",
-	      .offset		= MTDPART_OFS_APPEND,
-	      .size		= SZ_128K,
-	      .mask_flags	= 0,
-	},
-	/* kernel */
-	{
-	      .name		= "kernel",
-	      .offset		= MTDPART_OFS_APPEND,
-	      .size		= SZ_2M,
-	      .mask_flags	= 0
-	},
-	/* file system */
-	{
-	      .name		= "filesystem",
-	      .offset		= MTDPART_OFS_APPEND,
-	      .size		= MTDPART_SIZ_FULL,
-	      .mask_flags	= 0
-	}
-};
-
-static struct physmap_flash_data h4_flash_data = {
-	.width		= 2,
-	.parts		= h4_partitions,
-	.nr_parts	= ARRAY_SIZE(h4_partitions),
-};
-
-static struct resource h4_flash_resource = {
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device h4_flash_device = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &h4_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &h4_flash_resource,
-};
-
-static const struct display_timing cm_t35_lcd_videomode = {
-	.pixelclock	= { 0, 6250000, 0 },
-
-	.hactive = { 0, 240, 0 },
-	.hfront_porch = { 0, 15, 0 },
-	.hback_porch = { 0, 60, 0 },
-	.hsync_len = { 0, 15, 0 },
-
-	.vactive = { 0, 320, 0 },
-	.vfront_porch = { 0, 1, 0 },
-	.vback_porch = { 0, 1, 0 },
-	.vsync_len = { 0, 1, 0 },
-
-	.flags = DISPLAY_FLAGS_HSYNC_HIGH | DISPLAY_FLAGS_VSYNC_HIGH |
-		DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
-};
-
-static struct panel_dpi_platform_data cm_t35_lcd_pdata = {
-	.name                   = "lcd",
-	.source                 = "dpi.0",
-
-	.data_lines		= 16,
-
-	.display_timing		= &cm_t35_lcd_videomode,
-
-	.enable_gpio		= -1,
-	.backlight_gpio		= -1,
-};
-
-static struct platform_device cm_t35_lcd_device = {
-	.name                   = "panel-dpi",
-	.id                     = 0,
-	.dev.platform_data      = &cm_t35_lcd_pdata,
-};
-
-static struct platform_device *h4_devices[] __initdata = {
-	&h4_flash_device,
-	&cm_t35_lcd_device,
-};
-
-static struct omap_dss_board_info h4_dss_data = {
-	.default_display_name = "lcd",
-};
-
-/* 2420 Sysboot setup (2430 is different) */
-static u32 get_sysboot_value(void)
-{
-	return (omap_ctrl_readl(OMAP24XX_CONTROL_STATUS) &
-		(OMAP2_SYSBOOT_5_MASK | OMAP2_SYSBOOT_4_MASK |
-		 OMAP2_SYSBOOT_3_MASK | OMAP2_SYSBOOT_2_MASK |
-		 OMAP2_SYSBOOT_1_MASK | OMAP2_SYSBOOT_0_MASK));
-}
-
-/* H4-2420's always used muxed mode, H4-2422's always use non-muxed
- *
- * Note: OMAP-GIT doesn't correctly do is_cpu_omap2422 and is_cpu_omap2423
- *  correctly.  The macro needs to look at production_id not just hawkeye.
- */
-static u32 is_gpmc_muxed(void)
-{
-	u32 mux;
-	mux = get_sysboot_value();
-	if ((mux & 0xF) == 0xd)
-		return 1;	/* NAND config (could be either) */
-	if (mux & 0x2)		/* if mux'ed */
-		return 1;
-	else
-		return 0;
-}
-
-#if IS_ENABLED(CONFIG_SMC91X)
-
-static struct omap_smc91x_platform_data board_smc91x_data = {
-	.cs		= 1,
-	.gpio_irq	= 92,
-	.flags		= GPMC_TIMINGS_SMC91C96 | IORESOURCE_IRQ_LOWLEVEL,
-};
-
-static void __init board_smc91x_init(void)
-{
-	if (is_gpmc_muxed())
-		board_smc91x_data.flags |= GPMC_MUX_ADD_DATA;
-
-	omap_mux_init_gpio(board_smc91x_data.gpio_irq, OMAP_PIN_INPUT);
-	gpmc_smc91x_init(&board_smc91x_data);
-}
-
-#else
-
-static inline void board_smc91x_init(void)
-{
-}
-
-#endif
-
-static void __init h4_init_flash(void)
-{
-	unsigned long base;
-
-	if (gpmc_cs_request(H4_FLASH_CS, SZ_64M, &base) < 0) {
-		printk("Can't request GPMC CS for flash\n");
-		return;
-	}
-	h4_flash_resource.start	= base;
-	h4_flash_resource.end	= base + SZ_64M - 1;
-}
-
-static struct at24_platform_data m24c01 = {
-	.byte_len	= SZ_1K / 8,
-	.page_size	= 16,
-};
-
-static struct i2c_board_info __initdata h4_i2c_board_info[] = {
-	{
-		I2C_BOARD_INFO("isp1301_omap", 0x2d),
-	},
-	{	/* EEPROM on mainboard */
-		I2C_BOARD_INFO("24c01", 0x52),
-		.platform_data	= &m24c01,
-	},
-	{	/* EEPROM on cpu card */
-		I2C_BOARD_INFO("24c01", 0x57),
-		.platform_data	= &m24c01,
-	},
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init omap_h4_init(void)
-{
-	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAF);
-
-	/*
-	 * Make sure the serial ports are muxed on at this point.
-	 * You have to mux them off in device drivers later on
-	 * if not needed.
-	 */
-
-	board_mkp_init();
-	h4_i2c_board_info[0].irq = gpio_to_irq(125);
-	i2c_register_board_info(1, h4_i2c_board_info,
-			ARRAY_SIZE(h4_i2c_board_info));
-
-	platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
-	omap_serial_init();
-	omap_sdrc_init(NULL, NULL);
-	h4_init_flash();
-	board_smc91x_init();
-
-	omap_display_init(&h4_dss_data);
-}
-
-MACHINE_START(OMAP_H4, "OMAP2420 H4 board")
-	/* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap242x_map_io,
-	.init_early	= omap2420_init_early,
-	.init_irq	= omap2_init_irq,
-	.handle_irq	= omap2_intc_handle_irq,
-	.init_machine	= omap_h4_init,
-	.init_late	= omap2420_init_late,
-	.init_time	= omap2_sync32k_timer_init,
-	.restart	= omap2xxx_restart,
-MACHINE_END