Merge branch 'master' into sh/hwblk

Documentation/ABI/testing/sysfs-block

@@ -94,28 +94,37 @@ What:		/sys/block/<disk>/queue/physical_block_size
 Date:		May 2009
 Contact:	Martin K. Petersen <martin.petersen@oracle.com>
 Description:
-		This is the smallest unit the storage device can write
-		without resorting to read-modify-write operation.  It is
-		usually the same as the logical block size but may be
-		bigger.  One example is SATA drives with 4KB sectors
-		that expose a 512-byte logical block size to the
-		operating system.
+		This is the smallest unit a physical storage device can
+		write atomically.  It is usually the same as the logical
+		block size but may be bigger.  One example is SATA
+		drives with 4KB sectors that expose a 512-byte logical
+		block size to the operating system.  For stacked block
+		devices the physical_block_size variable contains the
+		maximum physical_block_size of the component devices.
 
 What:		/sys/block/<disk>/queue/minimum_io_size
 Date:		April 2009
 Contact:	Martin K. Petersen <martin.petersen@oracle.com>
 Description:
-		Storage devices may report a preferred minimum I/O size,
-		which is the smallest request the device can perform
-		without incurring a read-modify-write penalty.  For disk
-		drives this is often the physical block size.  For RAID
-		arrays it is often the stripe chunk size.
+		Storage devices may report a granularity or preferred
+		minimum I/O size which is the smallest request the
+		device can perform without incurring a performance
+		penalty.  For disk drives this is often the physical
+		block size.  For RAID arrays it is often the stripe
+		chunk size.  A properly aligned multiple of
+		minimum_io_size is the preferred request size for
+		workloads where a high number of I/O operations is
+		desired.
 
 What:		/sys/block/<disk>/queue/optimal_io_size
 Date:		April 2009
 Contact:	Martin K. Petersen <martin.petersen@oracle.com>
 Description:
 		Storage devices may report an optimal I/O size, which is
-		the device's preferred unit of receiving I/O.  This is
-		rarely reported for disk drives.  For RAID devices it is
-		usually the stripe width or the internal block size.
+		the device's preferred unit for sustained I/O.  This is
+		rarely reported for disk drives.  For RAID arrays it is
+		usually the stripe width or the internal track size.  A
+		properly aligned multiple of optimal_io_size is the
+		preferred request size for workloads where sustained
+		throughput is desired.  If no optimal I/O size is
+		reported this file contains 0.

Documentation/DocBook/kernel-hacking.tmpl

@@ -449,8 +449,8 @@ printk(KERN_INFO "i = %u\n", i);
    </para>
 
    <programlisting>
-__u32 ipaddress;
-printk(KERN_INFO "my ip: %d.%d.%d.%d\n", NIPQUAD(ipaddress));
+__be32 ipaddress;
+printk(KERN_INFO "my ip: %pI4\n", &amp;ipaddress);
    </programlisting>
 
    <para>

Documentation/arm/memory.txt

@@ -21,6 +21,8 @@ ffff8000	ffffffff	copy_user_page / clear_user_page use.
 				For SA11xx and Xscale, this is used to
 				setup a minicache mapping.
 
+ffff4000	ffffffff	cache aliasing on ARMv6 and later CPUs.
+
 ffff1000	ffff7fff	Reserved.
 				Platforms must not use this address range.
 

Documentation/ioctl/ioctl-number.txt

@@ -139,6 +139,7 @@ Code	Seq#	Include File		Comments
 'm'	all	linux/synclink.h	conflict!
 'm'	00-1F	net/irda/irmod.h	conflict!
 'n'	00-7F	linux/ncp_fs.h
+'n'	80-8F	linux/nilfs2_fs.h	NILFS2
 'n'	E0-FF	video/matrox.h          matroxfb
 'o'	00-1F	fs/ocfs2/ocfs2_fs.h	OCFS2
 'o'     00-03   include/mtd/ubi-user.h  conflict! (OCFS2 and UBI overlaps)

Documentation/kernel-parameters.txt

@@ -1115,6 +1115,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			libata.dma=4	  Compact Flash DMA only 
 			Combinations also work, so libata.dma=3 enables DMA
 			for disks and CDROMs, but not CFs.
+	
+	libata.ignore_hpa=	[LIBATA] Ignore HPA limit
+			libata.ignore_hpa=0	  keep BIOS limits (default)
+			libata.ignore_hpa=1	  ignore limits, using full disk
 
 	libata.noacpi	[LIBATA] Disables use of ACPI in libata suspend/resume
 			when set.

Documentation/laptops/thinkpad-acpi.txt

@@ -36,8 +36,6 @@ detailed description):
 	- Bluetooth enable and disable
 	- video output switching, expansion control
 	- ThinkLight on and off
-	- limited docking and undocking
-	- UltraBay eject
 	- CMOS/UCMS control
 	- LED control
 	- ACPI sounds
@@ -729,131 +727,6 @@ cannot be read or if it is unknown, thinkpad-acpi will report it as "off".
 It is impossible to know if the status returned through sysfs is valid.
 
 
-Docking / undocking -- /proc/acpi/ibm/dock
-------------------------------------------
-
-Docking and undocking (e.g. with the X4 UltraBase) requires some
-actions to be taken by the operating system to safely make or break
-the electrical connections with the dock.
-
-The docking feature of this driver generates the following ACPI events:
-
-	ibm/dock GDCK 00000003 00000001 -- eject request
-	ibm/dock GDCK 00000003 00000002 -- undocked
-	ibm/dock GDCK 00000000 00000003 -- docked
-
-NOTE: These events will only be generated if the laptop was docked
-when originally booted. This is due to the current lack of support for
-hot plugging of devices in the Linux ACPI framework. If the laptop was
-booted while not in the dock, the following message is shown in the
-logs:
-
-	Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present
-
-In this case, no dock-related events are generated but the dock and
-undock commands described below still work. They can be executed
-manually or triggered by Fn key combinations (see the example acpid
-configuration files included in the driver tarball package available
-on the web site).
-
-When the eject request button on the dock is pressed, the first event
-above is generated. The handler for this event should issue the
-following command:
-
-	echo undock > /proc/acpi/ibm/dock
-
-After the LED on the dock goes off, it is safe to eject the laptop.
-Note: if you pressed this key by mistake, go ahead and eject the
-laptop, then dock it back in. Otherwise, the dock may not function as
-expected.
-
-When the laptop is docked, the third event above is generated. The
-handler for this event should issue the following command to fully
-enable the dock:
-
-	echo dock > /proc/acpi/ibm/dock
-
-The contents of the /proc/acpi/ibm/dock file shows the current status
-of the dock, as provided by the ACPI framework.
-
-The docking support in this driver does not take care of enabling or
-disabling any other devices you may have attached to the dock. For
-example, a CD drive plugged into the UltraBase needs to be disabled or
-enabled separately. See the provided example acpid configuration files
-for how this can be accomplished.
-
-There is no support yet for PCI devices that may be attached to a
-docking station, e.g. in the ThinkPad Dock II. The driver currently
-does not recognize, enable or disable such devices. This means that
-the only docking stations currently supported are the X-series
-UltraBase docks and "dumb" port replicators like the Mini Dock (the
-latter don't need any ACPI support, actually).
-
-
-UltraBay eject -- /proc/acpi/ibm/bay
-------------------------------------
-
-Inserting or ejecting an UltraBay device requires some actions to be
-taken by the operating system to safely make or break the electrical
-connections with the device.
-
-This feature generates the following ACPI events:
-
-	ibm/bay MSTR 00000003 00000000 -- eject request
-	ibm/bay MSTR 00000001 00000000 -- eject lever inserted
-
-NOTE: These events will only be generated if the UltraBay was present
-when the laptop was originally booted (on the X series, the UltraBay
-is in the dock, so it may not be present if the laptop was undocked).
-This is due to the current lack of support for hot plugging of devices
-in the Linux ACPI framework. If the laptop was booted without the
-UltraBay, the following message is shown in the logs:
-
-	Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present
-
-In this case, no bay-related events are generated but the eject
-command described below still works. It can be executed manually or
-triggered by a hot key combination.
-
-Sliding the eject lever generates the first event shown above. The
-handler for this event should take whatever actions are necessary to
-shut down the device in the UltraBay (e.g. call idectl), then issue
-the following command:
-
-	echo eject > /proc/acpi/ibm/bay
-
-After the LED on the UltraBay goes off, it is safe to pull out the
-device.
-
-When the eject lever is inserted, the second event above is
-generated. The handler for this event should take whatever actions are
-necessary to enable the UltraBay device (e.g. call idectl).
-
-The contents of the /proc/acpi/ibm/bay file shows the current status
-of the UltraBay, as provided by the ACPI framework.
-
-EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use
-this feature, you need to supply the experimental=1 parameter when
-loading the module):
-
-These models do not have a button near the UltraBay device to request
-a hot eject but rather require the laptop to be put to sleep
-(suspend-to-ram) before the bay device is ejected or inserted).
-The sequence of steps to eject the device is as follows:
-
-	echo eject > /proc/acpi/ibm/bay
-	put the ThinkPad to sleep
-	remove the drive
-	resume from sleep
-	cat /proc/acpi/ibm/bay should show that the drive was removed
-
-On the A3x, both the UltraBay 2000 and UltraBay Plus devices are
-supported. Use "eject2" instead of "eject" for the second bay.
-
-Note: the UltraBay eject support on the 600e/x, A22p and A3x is
-EXPERIMENTAL and may not work as expected. USE WITH CAUTION!
-
-
 CMOS/UCMS control
 -----------------
 

Documentation/lguest/lguest.c

@@ -1,7 +1,9 @@
-/*P:100 This is the Launcher code, a simple program which lays out the
- * "physical" memory for the new Guest by mapping the kernel image and
- * the virtual devices, then opens /dev/lguest to tell the kernel
- * about the Guest and control it. :*/
+/*P:100
+ * This is the Launcher code, a simple program which lays out the "physical"
+ * memory for the new Guest by mapping the kernel image and the virtual
+ * devices, then opens /dev/lguest to tell the kernel about the Guest and
+ * control it.
+:*/
 #define _LARGEFILE64_SOURCE
 #define _GNU_SOURCE
 #include <stdio.h>
@@ -46,13 +48,15 @@
 #include "linux/virtio_rng.h"
 #include "linux/virtio_ring.h"
 #include "asm/bootparam.h"
-/*L:110 We can ignore the 39 include files we need for this program, but I do
- * want to draw attention to the use of kernel-style types.
+/*L:110
+ * We can ignore the 42 include files we need for this program, but I do want
+ * to draw attention to the use of kernel-style types.
  *
  * As Linus said, "C is a Spartan language, and so should your naming be."  I
  * like these abbreviations, so we define them here.  Note that u64 is always
  * unsigned long long, which works on all Linux systems: this means that we can
- * use %llu in printf for any u64. */
+ * use %llu in printf for any u64.
+ */
 typedef unsigned long long u64;
 typedef uint32_t u32;
 typedef uint16_t u16;
@@ -69,8 +73,10 @@ typedef uint8_t u8;
 /* This will occupy 3 pages: it must be a power of 2. */
 #define VIRTQUEUE_NUM 256
 
-/*L:120 verbose is both a global flag and a macro.  The C preprocessor allows
- * this, and although I wouldn't recommend it, it works quite nicely here. */
+/*L:120
+ * verbose is both a global flag and a macro.  The C preprocessor allows
+ * this, and although I wouldn't recommend it, it works quite nicely here.
+ */
 static bool verbose;
 #define verbose(args...) \
 	do { if (verbose) printf(args); } while(0)
@@ -87,8 +93,7 @@ static int lguest_fd;
 static unsigned int __thread cpu_id;
 
 /* This is our list of devices. */
-struct device_list
-{
+struct device_list {
 	/* Counter to assign interrupt numbers. */
 	unsigned int next_irq;
 
@@ -100,8 +105,7 @@ struct device_list
 
 	/* A single linked list of devices. */
 	struct device *dev;
-	/* And a pointer to the last device for easy append and also for
-	 * configuration appending. */
+	/* And a pointer to the last device for easy append. */
 	struct device *lastdev;
 };
 
@@ -109,8 +113,7 @@ struct device_list
 static struct device_list devices;
 
 /* The device structure describes a single device. */
-struct device
-{
+struct device {
 	/* The linked-list pointer. */
 	struct device *next;
 
@@ -135,8 +138,7 @@ struct device
 };
 
 /* The virtqueue structure describes a queue attached to a device. */
-struct virtqueue
-{
+struct virtqueue {
 	struct virtqueue *next;
 
 	/* Which device owns me. */
@@ -168,20 +170,24 @@ static char **main_args;
 /* The original tty settings to restore on exit. */
 static struct termios orig_term;
 
-/* We have to be careful with barriers: our devices are all run in separate
+/*
+ * We have to be careful with barriers: our devices are all run in separate
  * threads and so we need to make sure that changes visible to the Guest happen
- * in precise order. */
+ * in precise order.
+ */
 #define wmb() __asm__ __volatile__("" : : : "memory")
 #define mb() __asm__ __volatile__("" : : : "memory")
 
-/* Convert an iovec element to the given type.
+/*
+ * Convert an iovec element to the given type.
  *
  * This is a fairly ugly trick: we need to know the size of the type and
  * alignment requirement to check the pointer is kosher.  It's also nice to
  * have the name of the type in case we report failure.
  *
  * Typing those three things all the time is cumbersome and error prone, so we
- * have a macro which sets them all up and passes to the real function. */
+ * have a macro which sets them all up and passes to the real function.
+ */
 #define convert(iov, type) \
 	((type *)_convert((iov), sizeof(type), __alignof__(type), #type))
 
@@ -198,8 +204,10 @@ static void *_convert(struct iovec *iov, size_t size, size_t align,
 /* Wrapper for the last available index.  Makes it easier to change. */
 #define lg_last_avail(vq)	((vq)->last_avail_idx)
 
-/* The virtio configuration space is defined to be little-endian.  x86 is
- * little-endian too, but it's nice to be explicit so we have these helpers. */
+/*
+ * The virtio configuration space is defined to be little-endian.  x86 is
+ * little-endian too, but it's nice to be explicit so we have these helpers.
+ */
 #define cpu_to_le16(v16) (v16)
 #define cpu_to_le32(v32) (v32)
 #define cpu_to_le64(v64) (v64)
@@ -241,11 +249,12 @@ static u8 *get_feature_bits(struct device *dev)
 		+ dev->num_vq * sizeof(struct lguest_vqconfig);
 }
 
-/*L:100 The Launcher code itself takes us out into userspace, that scary place
- * where pointers run wild and free!  Unfortunately, like most userspace
- * programs, it's quite boring (which is why everyone likes to hack on the
- * kernel!).  Perhaps if you make up an Lguest Drinking Game at this point, it
- * will get you through this section.  Or, maybe not.
+/*L:100
+ * The Launcher code itself takes us out into userspace, that scary place where
+ * pointers run wild and free!  Unfortunately, like most userspace programs,
+ * it's quite boring (which is why everyone likes to hack on the kernel!).
+ * Perhaps if you make up an Lguest Drinking Game at this point, it will get
+ * you through this section.  Or, maybe not.
  *
  * The Launcher sets up a big chunk of memory to be the Guest's "physical"
  * memory and stores it in "guest_base".  In other words, Guest physical ==
@@ -253,7 +262,8 @@ static u8 *get_feature_bits(struct device *dev)
  *
  * This can be tough to get your head around, but usually it just means that we
  * use these trivial conversion functions when the Guest gives us it's
- * "physical" addresses: */
+ * "physical" addresses:
+ */
 static void *from_guest_phys(unsigned long addr)
 {
 	return guest_base + addr;
@@ -268,7 +278,8 @@ static unsigned long to_guest_phys(const void *addr)
  * Loading the Kernel.
  *
  * We start with couple of simple helper routines.  open_or_die() avoids
- * error-checking code cluttering the callers: */
+ * error-checking code cluttering the callers:
+ */
 static int open_or_die(const char *name, int flags)
 {
 	int fd = open(name, flags);
@@ -283,12 +294,19 @@ static void *map_zeroed_pages(unsigned int num)
 	int fd = open_or_die("/dev/zero", O_RDONLY);
 	void *addr;
 
-	/* We use a private mapping (ie. if we write to the page, it will be
-	 * copied). */
+	/*
+	 * We use a private mapping (ie. if we write to the page, it will be
+	 * copied).
+	 */
 	addr = mmap(NULL, getpagesize() * num,
 		    PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE, fd, 0);
 	if (addr == MAP_FAILED)
 		err(1, "Mmaping %u pages of /dev/zero", num);
+
+	/*
+	 * One neat mmap feature is that you can close the fd, and it
+	 * stays mapped.
+	 */
 	close(fd);
 
 	return addr;
@@ -305,20 +323,24 @@ static void *get_pages(unsigned int num)
 	return addr;
 }
 
-/* This routine is used to load the kernel or initrd.  It tries mmap, but if
+/*
+ * This routine is used to load the kernel or initrd.  It tries mmap, but if
  * that fails (Plan 9's kernel file isn't nicely aligned on page boundaries),
- * it falls back to reading the memory in. */
+ * it falls back to reading the memory in.
+ */
 static void map_at(int fd, void *addr, unsigned long offset, unsigned long len)
 {
 	ssize_t r;
 
-	/* We map writable even though for some segments are marked read-only.
+	/*
+	 * We map writable even though for some segments are marked read-only.
 	 * The kernel really wants to be writable: it patches its own
 	 * instructions.
 	 *
 	 * MAP_PRIVATE means that the page won't be copied until a write is
 	 * done to it.  This allows us to share untouched memory between
-	 * Guests. */
+	 * Guests.
+	 */
 	if (mmap(addr, len, PROT_READ|PROT_WRITE|PROT_EXEC,
 		 MAP_FIXED|MAP_PRIVATE, fd, offset) != MAP_FAILED)
 		return;
@@ -329,7 +351,8 @@ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len)
 		err(1, "Reading offset %lu len %lu gave %zi", offset, len, r);
 }
 
-/* This routine takes an open vmlinux image, which is in ELF, and maps it into
+/*
+ * This routine takes an open vmlinux image, which is in ELF, and maps it into
  * the Guest memory.  ELF = Embedded Linking Format, which is the format used
  * by all modern binaries on Linux including the kernel.
  *
@@ -337,23 +360,28 @@ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len)
  * address.  We use the physical address; the Guest will map itself to the
  * virtual address.
  *
- * We return the starting address. */
+ * We return the starting address.
+ */
 static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr)
 {
 	Elf32_Phdr phdr[ehdr->e_phnum];
 	unsigned int i;
 
-	/* Sanity checks on the main ELF header: an x86 executable with a
-	 * reasonable number of correctly-sized program headers. */
+	/*
+	 * Sanity checks on the main ELF header: an x86 executable with a
+	 * reasonable number of correctly-sized program headers.
+	 */
 	if (ehdr->e_type != ET_EXEC
 	    || ehdr->e_machine != EM_386
 	    || ehdr->e_phentsize != sizeof(Elf32_Phdr)
 	    || ehdr->e_phnum < 1 || ehdr->e_phnum > 65536U/sizeof(Elf32_Phdr))
 		errx(1, "Malformed elf header");
 
-	/* An ELF executable contains an ELF header and a number of "program"
+	/*
+	 * An ELF executable contains an ELF header and a number of "program"
 	 * headers which indicate which parts ("segments") of the program to
-	 * load where. */
+	 * load where.
+	 */
 
 	/* We read in all the program headers at once: */
 	if (lseek(elf_fd, ehdr->e_phoff, SEEK_SET) < 0)
@@ -361,8 +389,10 @@ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr)
 	if (read(elf_fd, phdr, sizeof(phdr)) != sizeof(phdr))
 		err(1, "Reading program headers");
 
-	/* Try all the headers: there are usually only three.  A read-only one,
-	 * a read-write one, and a "note" section which we don't load. */
+	/*
+	 * Try all the headers: there are usually only three.  A read-only one,
+	 * a read-write one, and a "note" section which we don't load.
+	 */
 	for (i = 0; i < ehdr->e_phnum; i++) {
 		/* If this isn't a loadable segment, we ignore it */
 		if (phdr[i].p_type != PT_LOAD)
@@ -380,13 +410,15 @@ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr)
 	return ehdr->e_entry;
 }
 
-/*L:150 A bzImage, unlike an ELF file, is not meant to be loaded.  You're
- * supposed to jump into it and it will unpack itself.  We used to have to
- * perform some hairy magic because the unpacking code scared me.
+/*L:150
+ * A bzImage, unlike an ELF file, is not meant to be loaded.  You're supposed
+ * to jump into it and it will unpack itself.  We used to have to perform some
+ * hairy magic because the unpacking code scared me.
  *
  * Fortunately, Jeremy Fitzhardinge convinced me it wasn't that hard and wrote
  * a small patch to jump over the tricky bits in the Guest, so now we just read
- * the funky header so we know where in the file to load, and away we go! */
+ * the funky header so we know where in the file to load, and away we go!
+ */
 static unsigned long load_bzimage(int fd)
 {
 	struct boot_params boot;
@@ -394,8 +426,10 @@ static unsigned long load_bzimage(int fd)
 	/* Modern bzImages get loaded at 1M. */
 	void *p = from_guest_phys(0x100000);
 
-	/* Go back to the start of the file and read the header.  It should be
-	 * a Linux boot header (see Documentation/x86/i386/boot.txt) */
+	/*
+	 * Go back to the start of the file and read the header.  It should be
+	 * a Linux boot header (see Documentation/x86/i386/boot.txt)
+	 */
 	lseek(fd, 0, SEEK_SET);
 	read(fd, &boot, sizeof(boot));
 
@@ -414,9 +448,11 @@ static unsigned long load_bzimage(int fd)
 	return boot.hdr.code32_start;
 }
 
-/*L:140 Loading the kernel is easy when it's a "vmlinux", but most kernels
+/*L:140
+ * Loading the kernel is easy when it's a "vmlinux", but most kernels
  * come wrapped up in the self-decompressing "bzImage" format.  With a little
- * work, we can load those, too. */
+ * work, we can load those, too.
+ */
 static unsigned long load_kernel(int fd)
 {
 	Elf32_Ehdr hdr;
@@ -433,24 +469,28 @@ static unsigned long load_kernel(int fd)
 	return load_bzimage(fd);
 }
 
-/* This is a trivial little helper to align pages.  Andi Kleen hated it because
+/*
+ * This is a trivial little helper to align pages.  Andi Kleen hated it because
  * it calls getpagesize() twice: "it's dumb code."
  *
  * Kernel guys get really het up about optimization, even when it's not
- * necessary.  I leave this code as a reaction against that. */
+ * necessary.  I leave this code as a reaction against that.
+ */
 static inline unsigned long page_align(unsigned long addr)
 {
 	/* Add upwards and truncate downwards. */
 	return ((addr + getpagesize()-1) & ~(getpagesize()-1));
 }
 
-/*L:180 An "initial ram disk" is a disk image loaded into memory along with
- * the kernel which the kernel can use to boot from without needing any
- * drivers.  Most distributions now use this as standard: the initrd contains
- * the code to load the appropriate driver modules for the current machine.
+/*L:180
+ * An "initial ram disk" is a disk image loaded into memory along with the
+ * kernel which the kernel can use to boot from without needing any drivers.
+ * Most distributions now use this as standard: the initrd contains the code to
+ * load the appropriate driver modules for the current machine.
  *
  * Importantly, James Morris works for RedHat, and Fedora uses initrds for its
- * kernels.  He sent me this (and tells me when I break it). */
+ * kernels.  He sent me this (and tells me when I break it).
+ */
 static unsigned long load_initrd(const char *name, unsigned long mem)
 {
 	int ifd;
@@ -462,12 +502,16 @@ static unsigned long load_initrd(const char *name, unsigned long mem)
 	if (fstat(ifd, &st) < 0)
 		err(1, "fstat() on initrd '%s'", name);
 
-	/* We map the initrd at the top of memory, but mmap wants it to be
-	 * page-aligned, so we round the size up for that. */
+	/*
+	 * We map the initrd at the top of memory, but mmap wants it to be
+	 * page-aligned, so we round the size up for that.
+	 */
 	len = page_align(st.st_size);
 	map_at(ifd, from_guest_phys(mem - len), 0, st.st_size);
-	/* Once a file is mapped, you can close the file descriptor.  It's a
-	 * little odd, but quite useful. */
+	/*
+	 * Once a file is mapped, you can close the file descriptor.  It's a
+	 * little odd, but quite useful.
+	 */
 	close(ifd);
 	verbose("mapped initrd %s size=%lu @ %p\n", name, len, (void*)mem-len);
 
@@ -476,8 +520,10 @@ static unsigned long load_initrd(const char *name, unsigned long mem)
 }
 /*:*/
 
-/* Simple routine to roll all the commandline arguments together with spaces
- * between them. */
+/*
+ * Simple routine to roll all the commandline arguments together with spaces
+ * between them.
+ */
 static void concat(char *dst, char *args[])
 {
 	unsigned int i, len = 0;
@@ -494,10 +540,12 @@ static void concat(char *dst, char *args[])
 	dst[len] = '\0';
 }
 
-/*L:185 This is where we actually tell the kernel to initialize the Guest.  We
+/*L:185
+ * This is where we actually tell the kernel to initialize the Guest.  We
  * saw the arguments it expects when we looked at initialize() in lguest_user.c:
  * the base of Guest "physical" memory, the top physical page to allow and the
- * entry point for the Guest. */
+ * entry point for the Guest.
+ */
 static void tell_kernel(unsigned long start)
 {
 	unsigned long args[] = { LHREQ_INITIALIZE,
@@ -511,7 +559,7 @@ static void tell_kernel(unsigned long start)
 }
 /*:*/
 
-/*
+/*L:200
  * Device Handling.
  *
  * When the Guest gives us a buffer, it sends an array of addresses and sizes.
@@ -522,20 +570,26 @@ static void tell_kernel(unsigned long start)
 static void *_check_pointer(unsigned long addr, unsigned int size,
 			    unsigned int line)
 {
-	/* We have to separately check addr and addr+size, because size could
-	 * be huge and addr + size might wrap around. */
+	/*
+	 * We have to separately check addr and addr+size, because size could
+	 * be huge and addr + size might wrap around.
+	 */
 	if (addr >= guest_limit || addr + size >= guest_limit)
 		errx(1, "%s:%i: Invalid address %#lx", __FILE__, line, addr);
-	/* We return a pointer for the caller's convenience, now we know it's
-	 * safe to use. */
+	/*
+	 * We return a pointer for the caller's convenience, now we know it's
+	 * safe to use.
+	 */
 	return from_guest_phys(addr);
 }
 /* A macro which transparently hands the line number to the real function. */
 #define check_pointer(addr,size) _check_pointer(addr, size, __LINE__)
 
-/* Each buffer in the virtqueues is actually a chain of descriptors.  This
+/*
+ * Each buffer in the virtqueues is actually a chain of descriptors.  This
  * function returns the next descriptor in the chain, or vq->vring.num if we're
- * at the end. */
+ * at the end.
+ */
 static unsigned next_desc(struct vring_desc *desc,
 			  unsigned int i, unsigned int max)
 {
@@ -556,7 +610,10 @@ static unsigned next_desc(struct vring_desc *desc,
 	return next;
 }
 
-/* This actually sends the interrupt for this virtqueue */
+/*
+ * This actually sends the interrupt for this virtqueue, if we've used a
+ * buffer.
+ */
 static void trigger_irq(struct virtqueue *vq)
 {
 	unsigned long buf[] = { LHREQ_IRQ, vq->config.irq };
@@ -576,12 +633,14 @@ static void trigger_irq(struct virtqueue *vq)
 		err(1, "Triggering irq %i", vq->config.irq);
 }
 
-/* This looks in the virtqueue and for the first available buffer, and converts
+/*
+ * This looks in the virtqueue for the first available buffer, and converts
  * it to an iovec for convenient access.  Since descriptors consist of some
  * number of output then some number of input descriptors, it's actually two
  * iovecs, but we pack them into one and note how many of each there were.
  *
- * This function returns the descriptor number found. */
+ * This function waits if necessary, and returns the descriptor number found.
+ */
 static unsigned wait_for_vq_desc(struct virtqueue *vq,
 				 struct iovec iov[],
 				 unsigned int *out_num, unsigned int *in_num)
@@ -590,17 +649,23 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 	struct vring_desc *desc;
 	u16 last_avail = lg_last_avail(vq);
 
+	/* There's nothing available? */
 	while (last_avail == vq->vring.avail->idx) {
 		u64 event;
 
-		/* OK, tell Guest about progress up to now. */
+		/*
+		 * Since we're about to sleep, now is a good time to tell the
+		 * Guest about what we've used up to now.
+		 */
 		trigger_irq(vq);
 
 		/* OK, now we need to know about added descriptors. */
 		vq->vring.used->flags &= ~VRING_USED_F_NO_NOTIFY;
 
-		/* They could have slipped one in as we were doing that: make
-		 * sure it's written, then check again. */
+		/*
+		 * They could have slipped one in as we were doing that: make
+		 * sure it's written, then check again.
+		 */
 		mb();
 		if (last_avail != vq->vring.avail->idx) {
 			vq->vring.used->flags |= VRING_USED_F_NO_NOTIFY;
@@ -620,8 +685,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 		errx(1, "Guest moved used index from %u to %u",
 		     last_avail, vq->vring.avail->idx);
 
-	/* Grab the next descriptor number they're advertising, and increment
-	 * the index we've seen. */
+	/*
+	 * Grab the next descriptor number they're advertising, and increment
+	 * the index we've seen.
+	 */
 	head = vq->vring.avail->ring[last_avail % vq->vring.num];
 	lg_last_avail(vq)++;
 
@@ -636,8 +703,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 	desc = vq->vring.desc;
 	i = head;
 
-	/* If this is an indirect entry, then this buffer contains a descriptor
-	 * table which we handle as if it's any normal descriptor chain. */
+	/*
+	 * If this is an indirect entry, then this buffer contains a descriptor
+	 * table which we handle as if it's any normal descriptor chain.
+	 */
 	if (desc[i].flags & VRING_DESC_F_INDIRECT) {
 		if (desc[i].len % sizeof(struct vring_desc))
 			errx(1, "Invalid size for indirect buffer table");
@@ -656,8 +725,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 		if (desc[i].flags & VRING_DESC_F_WRITE)
 			(*in_num)++;
 		else {
-			/* If it's an output descriptor, they're all supposed
-			 * to come before any input descriptors. */
+			/*
+			 * If it's an output descriptor, they're all supposed
+			 * to come before any input descriptors.
+			 */
 			if (*in_num)
 				errx(1, "Descriptor has out after in");
 			(*out_num)++;
@@ -671,14 +742,19 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 	return head;
 }
 
-/* After we've used one of their buffers, we tell them about it.  We'll then
- * want to send them an interrupt, using trigger_irq(). */
+/*
+ * After we've used one of their buffers, we tell the Guest about it.  Sometime
+ * later we'll want to send them an interrupt using trigger_irq(); note that
+ * wait_for_vq_desc() does that for us if it has to wait.
+ */
 static void add_used(struct virtqueue *vq, unsigned int head, int len)
 {
 	struct vring_used_elem *used;
 
-	/* The virtqueue contains a ring of used buffers.  Get a pointer to the
-	 * next entry in that used ring. */
+	/*
+	 * The virtqueue contains a ring of used buffers.  Get a pointer to the
+	 * next entry in that used ring.
+	 */
 	used = &vq->vring.used->ring[vq->vring.used->idx % vq->vring.num];
 	used->id = head;
 	used->len = len;
@@ -698,9 +774,9 @@ static void add_used_and_trigger(struct virtqueue *vq, unsigned head, int len)
 /*
  * The Console
  *
- * We associate some data with the console for our exit hack. */
-struct console_abort
-{
+ * We associate some data with the console for our exit hack.
+ */
+struct console_abort {
 	/* How many times have they hit ^C? */
 	int count;
 	/* When did they start? */
@@ -715,30 +791,35 @@ static void console_input(struct virtqueue *vq)
 	struct console_abort *abort = vq->dev->priv;
 	struct iovec iov[vq->vring.num];
 
-	/* Make sure there's a descriptor waiting. */
+	/* Make sure there's a descriptor available. */
 	head = wait_for_vq_desc(vq, iov, &out_num, &in_num);
 	if (out_num)
 		errx(1, "Output buffers in console in queue?");
 
-	/* Read it in. */
+	/* Read into it.  This is where we usually wait. */
 	len = readv(STDIN_FILENO, iov, in_num);
 	if (len <= 0) {
 		/* Ran out of input? */
 		warnx("Failed to get console input, ignoring console.");
-		/* For simplicity, dying threads kill the whole Launcher.  So
-		 * just nap here. */
+		/*
+		 * For simplicity, dying threads kill the whole Launcher.  So
+		 * just nap here.
+		 */
 		for (;;)
 			pause();
 	}
 
+	/* Tell the Guest we used a buffer. */
 	add_used_and_trigger(vq, head, len);
 
-	/* Three ^C within one second?  Exit.
+	/*
+	 * Three ^C within one second?  Exit.
 	 *
 	 * This is such a hack, but works surprisingly well.  Each ^C has to
 	 * be in a buffer by itself, so they can't be too fast.  But we check
 	 * that we get three within about a second, so they can't be too
-	 * slow. */
+	 * slow.
+	 */
 	if (len != 1 || ((char *)iov[0].iov_base)[0] != 3) {
 		abort->count = 0;
 		return;
@@ -763,15 +844,23 @@ static void console_output(struct virtqueue *vq)
 	unsigned int head, out, in;
 	struct iovec iov[vq->vring.num];
 
+	/* We usually wait in here, for the Guest to give us something. */
 	head = wait_for_vq_desc(vq, iov, &out, &in);
 	if (in)
 		errx(1, "Input buffers in console output queue?");
+
+	/* writev can return a partial write, so we loop here. */
 	while (!iov_empty(iov, out)) {
 		int len = writev(STDOUT_FILENO, iov, out);
 		if (len <= 0)
 			err(1, "Write to stdout gave %i", len);
 		iov_consume(iov, out, len);
 	}
+
+	/*
+	 * We're finished with that buffer: if we're going to sleep,
+	 * wait_for_vq_desc() will prod the Guest with an interrupt.
+	 */
 	add_used(vq, head, 0);
 }
 
@@ -791,15 +880,30 @@ static void net_output(struct virtqueue *vq)
 	unsigned int head, out, in;
 	struct iovec iov[vq->vring.num];
 
+	/* We usually wait in here for the Guest to give us a packet. */
 	head = wait_for_vq_desc(vq, iov, &out, &in);
 	if (in)
 		errx(1, "Input buffers in net output queue?");
+	/*
+	 * Send the whole thing through to /dev/net/tun.  It expects the exact
+	 * same format: what a coincidence!
+	 */
 	if (writev(net_info->tunfd, iov, out) < 0)
 		errx(1, "Write to tun failed?");
+
+	/*
+	 * Done with that one; wait_for_vq_desc() will send the interrupt if
+	 * all packets are processed.
+	 */
 	add_used(vq, head, 0);
 }
 
-/* Will reading from this file descriptor block? */
+/*
+ * Handling network input is a bit trickier, because I've tried to optimize it.
+ *
+ * First we have a helper routine which tells is if from this file descriptor
+ * (ie. the /dev/net/tun device) will block:
+ */
 static bool will_block(int fd)
 {
 	fd_set fdset;
@@ -809,8 +913,11 @@ static bool will_block(int fd)
 	return select(fd+1, &fdset, NULL, NULL, &zero) != 1;
 }
 
-/* This is where we handle packets coming in from the tun device to our
- * Guest. */
+/*
+ * This handles packets coming in from the tun device to our Guest.  Like all
+ * service routines, it gets called again as soon as it returns, so you don't
+ * see a while(1) loop here.
+ */
 static void net_input(struct virtqueue *vq)
 {
 	int len;
@@ -818,21 +925,38 @@ static void net_input(struct virtqueue *vq)
 	struct iovec iov[vq->vring.num];
 	struct net_info *net_info = vq->dev->priv;
 
+	/*
+	 * Get a descriptor to write an incoming packet into.  This will also
+	 * send an interrupt if they're out of descriptors.
+	 */
 	head = wait_for_vq_desc(vq, iov, &out, &in);
 	if (out)
 		errx(1, "Output buffers in net input queue?");
 
-	/* Deliver interrupt now, since we're about to sleep. */
+	/*
+	 * If it looks like we'll block reading from the tun device, send them
+	 * an interrupt.
+	 */
 	if (vq->pending_used && will_block(net_info->tunfd))
 		trigger_irq(vq);
 
+	/*
+	 * Read in the packet.  This is where we normally wait (when there's no
+	 * incoming network traffic).
+	 */
 	len = readv(net_info->tunfd, iov, in);
 	if (len <= 0)
 		err(1, "Failed to read from tun.");
+
+	/*
+	 * Mark that packet buffer as used, but don't interrupt here.  We want
+	 * to wait until we've done as much work as we can.
+	 */
 	add_used(vq, head, len);
 }
+/*:*/
 
-/* This is the helper to create threads. */
+/* This is the helper to create threads: run the service routine in a loop. */
 static int do_thread(void *_vq)
 {
 	struct virtqueue *vq = _vq;
@@ -842,8 +966,10 @@ static int do_thread(void *_vq)
 	return 0;
 }
 
-/* When a child dies, we kill our entire process group with SIGTERM.  This
- * also has the side effect that the shell restores the console for us! */
+/*
+ * When a child dies, we kill our entire process group with SIGTERM.  This
+ * also has the side effect that the shell restores the console for us!
+ */
 static void kill_launcher(int signal)
 {
 	kill(0, SIGTERM);
@@ -878,11 +1004,15 @@ static void reset_device(struct device *dev)
 	signal(SIGCHLD, (void *)kill_launcher);
 }
 
+/*L:216
+ * This actually creates the thread which services the virtqueue for a device.
+ */
 static void create_thread(struct virtqueue *vq)
 {
-	/* Create stack for thread and run it.  Since stack grows
-	 * upwards, we point the stack pointer to the end of this
-	 * region. */
+	/*
+	 * Create stack for thread.  Since the stack grows upwards, we point
+	 * the stack pointer to the end of this region.
+	 */
 	char *stack = malloc(32768);
 	unsigned long args[] = { LHREQ_EVENTFD,
 				 vq->config.pfn*getpagesize(), 0 };
@@ -893,17 +1023,22 @@ static void create_thread(struct virtqueue *vq)
 		err(1, "Creating eventfd");
 	args[2] = vq->eventfd;
 
-	/* Attach an eventfd to this virtqueue: it will go off
-	 * when the Guest does an LHCALL_NOTIFY for this vq. */
+	/*
+	 * Attach an eventfd to this virtqueue: it will go off when the Guest
+	 * does an LHCALL_NOTIFY for this vq.
+	 */
 	if (write(lguest_fd, &args, sizeof(args)) != 0)
 		err(1, "Attaching eventfd");
 
-	/* CLONE_VM: because it has to access the Guest memory, and
-	 * SIGCHLD so we get a signal if it dies. */
+	/*
+	 * CLONE_VM: because it has to access the Guest memory, and SIGCHLD so
+	 * we get a signal if it dies.
+	 */
 	vq->thread = clone(do_thread, stack + 32768, CLONE_VM | SIGCHLD, vq);
 	if (vq->thread == (pid_t)-1)
 		err(1, "Creating clone");
-	/* We close our local copy, now the child has it. */
+
+	/* We close our local copy now the child has it. */
 	close(vq->eventfd);
 }
 
@@ -955,7 +1090,10 @@ static void update_device_status(struct device *dev)
 	}
 }
 
-/* This is the generic routine we call when the Guest uses LHCALL_NOTIFY. */
+/*L:215
+ * This is the generic routine we call when the Guest uses LHCALL_NOTIFY.  In
+ * particular, it's used to notify us of device status changes during boot.
+ */
 static void handle_output(unsigned long addr)
 {
 	struct device *i;
@@ -964,25 +1102,42 @@ static void handle_output(unsigned long addr)
 	for (i = devices.dev; i; i = i->next) {
 		struct virtqueue *vq;
 
-		/* Notifications to device descriptors update device status. */
+		/*
+		 * Notifications to device descriptors mean they updated the
+		 * device status.
+		 */
 		if (from_guest_phys(addr) == i->desc) {
 			update_device_status(i);
 			return;
 		}
 
-		/* Devices *can* be used before status is set to DRIVER_OK. */
+		/*
+		 * Devices *can* be used before status is set to DRIVER_OK.
+		 * The original plan was that they would never do this: they
+		 * would always finish setting up their status bits before
+		 * actually touching the virtqueues.  In practice, we allowed
+		 * them to, and they do (eg. the disk probes for partition
+		 * tables as part of initialization).
+		 *
+		 * If we see this, we start the device: once it's running, we
+		 * expect the device to catch all the notifications.
+		 */
 		for (vq = i->vq; vq; vq = vq->next) {
 			if (addr != vq->config.pfn*getpagesize())
 				continue;
 			if (i->running)
 				errx(1, "Notification on running %s", i->name);
+			/* This just calls create_thread() for each virtqueue */
 			start_device(i);
 			return;
 		}
 	}
 
-	/* Early console write is done using notify on a nul-terminated string
-	 * in Guest memory. */
+	/*
+	 * Early console write is done using notify on a nul-terminated string
+	 * in Guest memory.  It's also great for hacking debugging messages
+	 * into a Guest.
+	 */
 	if (addr >= guest_limit)
 		errx(1, "Bad NOTIFY %#lx", addr);
 
@@ -998,10 +1153,12 @@ static void handle_output(unsigned long addr)
  * routines to allocate and manage them.
  */
 
-/* The layout of the device page is a "struct lguest_device_desc" followed by a
+/*
+ * The layout of the device page is a "struct lguest_device_desc" followed by a
  * number of virtqueue descriptors, then two sets of feature bits, then an
  * array of configuration bytes.  This routine returns the configuration
- * pointer. */
+ * pointer.
+ */
 static u8 *device_config(const struct device *dev)
 {
 	return (void *)(dev->desc + 1)
@@ -1009,9 +1166,11 @@ static u8 *device_config(const struct device *dev)
 		+ dev->feature_len * 2;
 }
 
-/* This routine allocates a new "struct lguest_device_desc" from descriptor
+/*
+ * This routine allocates a new "struct lguest_device_desc" from descriptor
  * table page just above the Guest's normal memory.  It returns a pointer to
- * that descriptor. */
+ * that descriptor.
+ */
 static struct lguest_device_desc *new_dev_desc(u16 type)
 {
 	struct lguest_device_desc d = { .type = type };
@@ -1032,8 +1191,10 @@ static struct lguest_device_desc *new_dev_desc(u16 type)
 	return memcpy(p, &d, sizeof(d));
 }
 
-/* Each device descriptor is followed by the description of its virtqueues.  We
- * specify how many descriptors the virtqueue is to have. */
+/*
+ * Each device descriptor is followed by the description of its virtqueues.  We
+ * specify how many descriptors the virtqueue is to have.
+ */
 static void add_virtqueue(struct device *dev, unsigned int num_descs,
 			  void (*service)(struct virtqueue *))
 {
@@ -1050,6 +1211,11 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs,
 	vq->next = NULL;
 	vq->last_avail_idx = 0;
 	vq->dev = dev;
+
+	/*
+	 * This is the routine the service thread will run, and its Process ID
+	 * once it's running.
+	 */
 	vq->service = service;
 	vq->thread = (pid_t)-1;
 
@@ -1061,10 +1227,12 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs,
 	/* Initialize the vring. */
 	vring_init(&vq->vring, num_descs, p, LGUEST_VRING_ALIGN);
 
-	/* Append virtqueue to this device's descriptor.  We use
+	/*
+	 * Append virtqueue to this device's descriptor.  We use
 	 * device_config() to get the end of the device's current virtqueues;
 	 * we check that we haven't added any config or feature information
-	 * yet, otherwise we'd be overwriting them. */
+	 * yet, otherwise we'd be overwriting them.
+	 */
 	assert(dev->desc->config_len == 0 && dev->desc->feature_len == 0);
 	memcpy(device_config(dev), &vq->config, sizeof(vq->config));
 	dev->num_vq++;
@@ -1072,14 +1240,18 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs,
 
 	verbose("Virtqueue page %#lx\n", to_guest_phys(p));
 
-	/* Add to tail of list, so dev->vq is first vq, dev->vq->next is
-	 * second.  */
+	/*
+	 * Add to tail of list, so dev->vq is first vq, dev->vq->next is
+	 * second.
+	 */
 	for (i = &dev->vq; *i; i = &(*i)->next);
 	*i = vq;
 }
 
-/* The first half of the feature bitmask is for us to advertise features.  The
- * second half is for the Guest to accept features. */
+/*
+ * The first half of the feature bitmask is for us to advertise features.  The
+ * second half is for the Guest to accept features.
+ */
 static void add_feature(struct device *dev, unsigned bit)
 {
 	u8 *features = get_feature_bits(dev);
@@ -1093,9 +1265,11 @@ static void add_feature(struct device *dev, unsigned bit)
 	features[bit / CHAR_BIT] |= (1 << (bit % CHAR_BIT));
 }
 
-/* This routine sets the configuration fields for an existing device's
+/*
+ * This routine sets the configuration fields for an existing device's
  * descriptor.  It only works for the last device, but that's OK because that's
- * how we use it. */
+ * how we use it.
+ */
 static void set_config(struct device *dev, unsigned len, const void *conf)
 {
 	/* Check we haven't overflowed our single page. */
@@ -1105,12 +1279,18 @@ static void set_config(struct device *dev, unsigned len, const void *conf)
 	/* Copy in the config information, and store the length. */
 	memcpy(device_config(dev), conf, len);
 	dev->desc->config_len = len;
+
+	/* Size must fit in config_len field (8 bits)! */
+	assert(dev->desc->config_len == len);
 }
 
-/* This routine does all the creation and setup of a new device, including
- * calling new_dev_desc() to allocate the descriptor and device memory.
+/*
+ * This routine does all the creation and setup of a new device, including
+ * calling new_dev_desc() to allocate the descriptor and device memory.  We
+ * don't actually start the service threads until later.
  *
- * See what I mean about userspace being boring? */
+ * See what I mean about userspace being boring?
+ */
 static struct device *new_device(const char *name, u16 type)
 {
 	struct device *dev = malloc(sizeof(*dev));
@@ -1123,10 +1303,12 @@ static struct device *new_device(const char *name, u16 type)
 	dev->num_vq = 0;
 	dev->running = false;
 
-	/* Append to device list.  Prepending to a single-linked list is
+	/*
+	 * Append to device list.  Prepending to a single-linked list is
 	 * easier, but the user expects the devices to be arranged on the bus
 	 * in command-line order.  The first network device on the command line
-	 * is eth0, the first block device /dev/vda, etc. */
+	 * is eth0, the first block device /dev/vda, etc.
+	 */
 	if (devices.lastdev)
 		devices.lastdev->next = dev;
 	else
@@ -1136,8 +1318,10 @@ static struct device *new_device(const char *name, u16 type)
 	return dev;
 }
 
-/* Our first setup routine is the console.  It's a fairly simple device, but
- * UNIX tty handling makes it uglier than it could be. */
+/*
+ * Our first setup routine is the console.  It's a fairly simple device, but
+ * UNIX tty handling makes it uglier than it could be.
+ */
 static void setup_console(void)
 {
 	struct device *dev;
@@ -1145,8 +1329,10 @@ static void setup_console(void)
 	/* If we can save the initial standard input settings... */
 	if (tcgetattr(STDIN_FILENO, &orig_term) == 0) {
 		struct termios term = orig_term;
-		/* Then we turn off echo, line buffering and ^C etc.  We want a
-		 * raw input stream to the Guest. */
+		/*
+		 * Then we turn off echo, line buffering and ^C etc: We want a
+		 * raw input stream to the Guest.
+		 */
 		term.c_lflag &= ~(ISIG|ICANON|ECHO);
 		tcsetattr(STDIN_FILENO, TCSANOW, &term);
 	}
@@ -1157,10 +1343,12 @@ static void setup_console(void)
 	dev->priv = malloc(sizeof(struct console_abort));
 	((struct console_abort *)dev->priv)->count = 0;
 
-	/* The console needs two virtqueues: the input then the output.  When
+	/*
+	 * The console needs two virtqueues: the input then the output.  When
 	 * they put something the input queue, we make sure we're listening to
 	 * stdin.  When they put something in the output queue, we write it to
-	 * stdout. */
+	 * stdout.
+	 */
 	add_virtqueue(dev, VIRTQUEUE_NUM, console_input);
 	add_virtqueue(dev, VIRTQUEUE_NUM, console_output);
 
@@ -1168,7 +1356,8 @@ static void setup_console(void)
 }
 /*:*/
 
-/*M:010 Inter-guest networking is an interesting area.  Simplest is to have a
+/*M:010
+ * Inter-guest networking is an interesting area.  Simplest is to have a
  * --sharenet=<name> option which opens or creates a named pipe.  This can be
  * used to send packets to another guest in a 1:1 manner.
  *
@@ -1182,7 +1371,8 @@ static void setup_console(void)
  * multiple inter-guest channels behind one interface, although it would
  * require some manner of hotplugging new virtio channels.
  *
- * Finally, we could implement a virtio network switch in the kernel. :*/
+ * Finally, we could implement a virtio network switch in the kernel.
+:*/
 
 static u32 str2ip(const char *ipaddr)
 {
@@ -1207,11 +1397,13 @@ static void str2mac(const char *macaddr, unsigned char mac[6])
 	mac[5] = m[5];
 }
 
-/* This code is "adapted" from libbridge: it attaches the Host end of the
+/*
+ * This code is "adapted" from libbridge: it attaches the Host end of the
  * network device to the bridge device specified by the command line.
  *
  * This is yet another James Morris contribution (I'm an IP-level guy, so I
- * dislike bridging), and I just try not to break it. */
+ * dislike bridging), and I just try not to break it.
+ */
 static void add_to_bridge(int fd, const char *if_name, const char *br_name)
 {
 	int ifidx;
@@ -1231,9 +1423,11 @@ static void add_to_bridge(int fd, const char *if_name, const char *br_name)
 		err(1, "can't add %s to bridge %s", if_name, br_name);
 }
 
-/* This sets up the Host end of the network device with an IP address, brings
+/*
+ * This sets up the Host end of the network device with an IP address, brings
  * it up so packets will flow, the copies the MAC address into the hwaddr
- * pointer. */
+ * pointer.
+ */
 static void configure_device(int fd, const char *tapif, u32 ipaddr)
 {
 	struct ifreq ifr;
@@ -1260,10 +1454,12 @@ static int get_tun_device(char tapif[IFNAMSIZ])
 	/* Start with this zeroed.  Messy but sure. */
 	memset(&ifr, 0, sizeof(ifr));
 
-	/* We open the /dev/net/tun device and tell it we want a tap device.  A
+	/*
+	 * We open the /dev/net/tun device and tell it we want a tap device.  A
 	 * tap device is like a tun device, only somehow different.  To tell
 	 * the truth, I completely blundered my way through this code, but it
-	 * works now! */
+	 * works now!
+	 */
 	netfd = open_or_die("/dev/net/tun", O_RDWR);
 	ifr.ifr_flags = IFF_TAP | IFF_NO_PI | IFF_VNET_HDR;
 	strcpy(ifr.ifr_name, "tap%d");
@@ -1274,18 +1470,22 @@ static int get_tun_device(char tapif[IFNAMSIZ])
 		  TUN_F_CSUM|TUN_F_TSO4|TUN_F_TSO6|TUN_F_TSO_ECN) != 0)
 		err(1, "Could not set features for tun device");
 
-	/* We don't need checksums calculated for packets coming in this
-	 * device: trust us! */
+	/*
+	 * We don't need checksums calculated for packets coming in this
+	 * device: trust us!
+	 */
 	ioctl(netfd, TUNSETNOCSUM, 1);
 
 	memcpy(tapif, ifr.ifr_name, IFNAMSIZ);
 	return netfd;
 }
 
-/*L:195 Our network is a Host<->Guest network.  This can either use bridging or
+/*L:195
+ * Our network is a Host<->Guest network.  This can either use bridging or
  * routing, but the principle is the same: it uses the "tun" device to inject
  * packets into the Host as if they came in from a normal network card.  We
- * just shunt packets between the Guest and the tun device. */
+ * just shunt packets between the Guest and the tun device.
+ */
 static void setup_tun_net(char *arg)
 {
 	struct device *dev;
@@ -1302,13 +1502,14 @@ static void setup_tun_net(char *arg)
 	dev = new_device("net", VIRTIO_ID_NET);
 	dev->priv = net_info;
 
-	/* Network devices need a receive and a send queue, just like
-	 * console. */
+	/* Network devices need a recv and a send queue, just like console. */
 	add_virtqueue(dev, VIRTQUEUE_NUM, net_input);
 	add_virtqueue(dev, VIRTQUEUE_NUM, net_output);
 
-	/* We need a socket to perform the magic network ioctls to bring up the
-	 * tap interface, connect to the bridge etc.  Any socket will do! */
+	/*
+	 * We need a socket to perform the magic network ioctls to bring up the
+	 * tap interface, connect to the bridge etc.  Any socket will do!
+	 */
 	ipfd = socket(PF_INET, SOCK_DGRAM, IPPROTO_IP);
 	if (ipfd < 0)
 		err(1, "opening IP socket");
@@ -1362,39 +1563,31 @@ static void setup_tun_net(char *arg)
 		verbose("device %u: tun %s: %s\n",
 			devices.device_num, tapif, arg);
 }
-
-/* Our block (disk) device should be really simple: the Guest asks for a block
- * number and we read or write that position in the file.  Unfortunately, that
- * was amazingly slow: the Guest waits until the read is finished before
- * running anything else, even if it could have been doing useful work.
- *
- * We could use async I/O, except it's reputed to suck so hard that characters
- * actually go missing from your code when you try to use it.
- *
- * So we farm the I/O out to thread, and communicate with it via a pipe. */
+/*:*/
 
 /* This hangs off device->priv. */
-struct vblk_info
-{
+struct vblk_info {
 	/* The size of the file. */
 	off64_t len;
 
 	/* The file descriptor for the file. */
 	int fd;
 
-	/* IO thread listens on this file descriptor [0]. */
-	int workpipe[2];
-
-	/* IO thread writes to this file descriptor to mark it done, then
-	 * Launcher triggers interrupt to Guest. */
-	int done_fd;
 };
 
 /*L:210
  * The Disk
  *
- * Remember that the block device is handled by a separate I/O thread.  We head
- * straight into the core of that thread here:
+ * The disk only has one virtqueue, so it only has one thread.  It is really
+ * simple: the Guest asks for a block number and we read or write that position
+ * in the file.
+ *
+ * Before we serviced each virtqueue in a separate thread, that was unacceptably
+ * slow: the Guest waits until the read is finished before running anything
+ * else, even if it could have been doing useful work.
+ *
+ * We could have used async I/O, except it's reputed to suck so hard that
+ * characters actually go missing from your code when you try to use it.
  */
 static void blk_request(struct virtqueue *vq)
 {
@@ -1406,47 +1599,64 @@ static void blk_request(struct virtqueue *vq)
 	struct iovec iov[vq->vring.num];
 	off64_t off;
 
-	/* Get the next request. */
+	/*
+	 * Get the next request, where we normally wait.  It triggers the
+	 * interrupt to acknowledge previously serviced requests (if any).
+	 */
 	head = wait_for_vq_desc(vq, iov, &out_num, &in_num);
 
-	/* Every block request should contain at least one output buffer
+	/*
+	 * Every block request should contain at least one output buffer
 	 * (detailing the location on disk and the type of request) and one
-	 * input buffer (to hold the result). */
+	 * input buffer (to hold the result).
+	 */
 	if (out_num == 0 || in_num == 0)
 		errx(1, "Bad virtblk cmd %u out=%u in=%u",
 		     head, out_num, in_num);
 
 	out = convert(&iov[0], struct virtio_blk_outhdr);
 	in = convert(&iov[out_num+in_num-1], u8);
+	/*
+	 * For historical reasons, block operations are expressed in 512 byte
+	 * "sectors".
+	 */
 	off = out->sector * 512;
 
-	/* The block device implements "barriers", where the Guest indicates
+	/*
+	 * The block device implements "barriers", where the Guest indicates
 	 * that it wants all previous writes to occur before this write.  We
 	 * don't have a way of asking our kernel to do a barrier, so we just
-	 * synchronize all the data in the file.  Pretty poor, no? */
+	 * synchronize all the data in the file.  Pretty poor, no?
+	 */
 	if (out->type & VIRTIO_BLK_T_BARRIER)
 		fdatasync(vblk->fd);
 
-	/* In general the virtio block driver is allowed to try SCSI commands.
-	 * It'd be nice if we supported eject, for example, but we don't. */
+	/*
+	 * In general the virtio block driver is allowed to try SCSI commands.
+	 * It'd be nice if we supported eject, for example, but we don't.
+	 */
 	if (out->type & VIRTIO_BLK_T_SCSI_CMD) {
 		fprintf(stderr, "Scsi commands unsupported\n");
 		*in = VIRTIO_BLK_S_UNSUPP;
 		wlen = sizeof(*in);
 	} else if (out->type & VIRTIO_BLK_T_OUT) {
-		/* Write */
-
-		/* Move to the right location in the block file.  This can fail
-		 * if they try to write past end. */
+		/*
+		 * Write
+		 *
+		 * Move to the right location in the block file.  This can fail
+		 * if they try to write past end.
+		 */
 		if (lseek64(vblk->fd, off, SEEK_SET) != off)
 			err(1, "Bad seek to sector %llu", out->sector);
 
 		ret = writev(vblk->fd, iov+1, out_num-1);
 		verbose("WRITE to sector %llu: %i\n", out->sector, ret);
 
-		/* Grr... Now we know how long the descriptor they sent was, we
+		/*
+		 * Grr... Now we know how long the descriptor they sent was, we
 		 * make sure they didn't try to write over the end of the block
-		 * file (possibly extending it). */
+		 * file (possibly extending it).
+		 */
 		if (ret > 0 && off + ret > vblk->len) {
 			/* Trim it back to the correct length */
 			ftruncate64(vblk->fd, vblk->len);
@@ -1456,10 +1666,12 @@ static void blk_request(struct virtqueue *vq)
 		wlen = sizeof(*in);
 		*in = (ret >= 0 ? VIRTIO_BLK_S_OK : VIRTIO_BLK_S_IOERR);
 	} else {
-		/* Read */
-
-		/* Move to the right location in the block file.  This can fail
-		 * if they try to read past end. */
+		/*
+		 * Read
+		 *
+		 * Move to the right location in the block file.  This can fail
+		 * if they try to read past end.
+		 */
 		if (lseek64(vblk->fd, off, SEEK_SET) != off)
 			err(1, "Bad seek to sector %llu", out->sector);
 
@@ -1474,13 +1686,16 @@ static void blk_request(struct virtqueue *vq)
 		}
 	}
 
-	/* OK, so we noted that it was pretty poor to use an fdatasync as a
+	/*
+	 * OK, so we noted that it was pretty poor to use an fdatasync as a
 	 * barrier.  But Christoph Hellwig points out that we need a sync
 	 * *afterwards* as well: "Barriers specify no reordering to the front
-	 * or the back."  And Jens Axboe confirmed it, so here we are: */
+	 * or the back."  And Jens Axboe confirmed it, so here we are:
+	 */
 	if (out->type & VIRTIO_BLK_T_BARRIER)
 		fdatasync(vblk->fd);
 
+	/* Finished that request. */
 	add_used(vq, head, wlen);
 }
 
@@ -1491,7 +1706,7 @@ static void setup_block_file(const char *filename)
 	struct vblk_info *vblk;
 	struct virtio_blk_config conf;
 
-	/* The device responds to return from I/O thread. */
+	/* Creat the device. */
 	dev = new_device("block", VIRTIO_ID_BLOCK);
 
 	/* The device has one virtqueue, where the Guest places requests. */
@@ -1510,27 +1725,32 @@ static void setup_block_file(const char *filename)
 	/* Tell Guest how many sectors this device has. */
 	conf.capacity = cpu_to_le64(vblk->len / 512);
 
-	/* Tell Guest not to put in too many descriptors at once: two are used
-	 * for the in and out elements. */
+	/*
+	 * Tell Guest not to put in too many descriptors at once: two are used
+	 * for the in and out elements.
+	 */
 	add_feature(dev, VIRTIO_BLK_F_SEG_MAX);
 	conf.seg_max = cpu_to_le32(VIRTQUEUE_NUM - 2);
 
-	set_config(dev, sizeof(conf), &conf);
+	/* Don't try to put whole struct: we have 8 bit limit. */
+	set_config(dev, offsetof(struct virtio_blk_config, geometry), &conf);
 
 	verbose("device %u: virtblock %llu sectors\n",
 		++devices.device_num, le64_to_cpu(conf.capacity));
 }
 
-struct rng_info {
-	int rfd;
-};
-
-/* Our random number generator device reads from /dev/random into the Guest's
+/*L:211
+ * Our random number generator device reads from /dev/random into the Guest's
  * input buffers.  The usual case is that the Guest doesn't want random numbers
  * and so has no buffers although /dev/random is still readable, whereas
  * console is the reverse.
  *
- * The same logic applies, however. */
+ * The same logic applies, however.
+ */
+struct rng_info {
+	int rfd;
+};
+
 static void rng_input(struct virtqueue *vq)
 {
 	int len;
@@ -1543,9 +1763,10 @@ static void rng_input(struct virtqueue *vq)
 	if (out_num)
 		errx(1, "Output buffers in rng?");
 
-	/* This is why we convert to iovecs: the readv() call uses them, and so
-	 * it reads straight into the Guest's buffer.  We loop to make sure we
-	 * fill it. */
+	/*
+	 * Just like the console write, we loop to cover the whole iovec.
+	 * In this case, short reads actually happen quite a bit.
+	 */
 	while (!iov_empty(iov, in_num)) {
 		len = readv(rng_info->rfd, iov, in_num);
 		if (len <= 0)
@@ -1558,15 +1779,18 @@ static void rng_input(struct virtqueue *vq)
 	add_used(vq, head, totlen);
 }
 
-/* And this creates a "hardware" random number device for the Guest. */
+/*L:199
+ * This creates a "hardware" random number device for the Guest.
+ */
 static void setup_rng(void)
 {
 	struct device *dev;
 	struct rng_info *rng_info = malloc(sizeof(*rng_info));
 
+	/* Our device's privat info simply contains the /dev/random fd. */
 	rng_info->rfd = open_or_die("/dev/random", O_RDONLY);
 
-	/* The device responds to return from I/O thread. */
+	/* Create the new device. */
 	dev = new_device("rng", VIRTIO_ID_RNG);
 	dev->priv = rng_info;
 
@@ -1582,8 +1806,10 @@ static void __attribute__((noreturn)) restart_guest(void)
 {
 	unsigned int i;
 
-	/* Since we don't track all open fds, we simply close everything beyond
-	 * stderr. */
+	/*
+	 * Since we don't track all open fds, we simply close everything beyond
+	 * stderr.
+	 */
 	for (i = 3; i < FD_SETSIZE; i++)
 		close(i);
 
@@ -1594,8 +1820,10 @@ static void __attribute__((noreturn)) restart_guest(void)
 	err(1, "Could not exec %s", main_args[0]);
 }
 
-/*L:220 Finally we reach the core of the Launcher which runs the Guest, serves
- * its input and output, and finally, lays it to rest. */
+/*L:220
+ * Finally we reach the core of the Launcher which runs the Guest, serves
+ * its input and output, and finally, lays it to rest.
+ */
 static void __attribute__((noreturn)) run_guest(void)
 {
 	for (;;) {
@@ -1630,7 +1858,7 @@ static void __attribute__((noreturn)) run_guest(void)
  *
  * Are you ready?  Take a deep breath and join me in the core of the Host, in
  * "make Host".
- :*/
+:*/
 
 static struct option opts[] = {
 	{ "verbose", 0, NULL, 'v' },
@@ -1651,8 +1879,7 @@ static void usage(void)
 /*L:105 The main routine is where the real work begins: */
 int main(int argc, char *argv[])
 {
-	/* Memory, top-level pagetable, code startpoint and size of the
-	 * (optional) initrd. */
+	/* Memory, code startpoint and size of the (optional) initrd. */
 	unsigned long mem = 0, start, initrd_size = 0;
 	/* Two temporaries. */
 	int i, c;
@@ -1664,24 +1891,32 @@ int main(int argc, char *argv[])
 	/* Save the args: we "reboot" by execing ourselves again. */
 	main_args = argv;
 
-	/* First we initialize the device list.  We keep a pointer to the last
+	/*
+	 * First we initialize the device list.  We keep a pointer to the last
 	 * device, and the next interrupt number to use for devices (1:
-	 * remember that 0 is used by the timer). */
+	 * remember that 0 is used by the timer).
+	 */
 	devices.lastdev = NULL;
 	devices.next_irq = 1;
 
+	/* We're CPU 0.  In fact, that's the only CPU possible right now. */
 	cpu_id = 0;
-	/* We need to know how much memory so we can set up the device
+
+	/*
+	 * We need to know how much memory so we can set up the device
 	 * descriptor and memory pages for the devices as we parse the command
 	 * line.  So we quickly look through the arguments to find the amount
-	 * of memory now. */
+	 * of memory now.
+	 */
 	for (i = 1; i < argc; i++) {
 		if (argv[i][0] != '-') {
 			mem = atoi(argv[i]) * 1024 * 1024;
-			/* We start by mapping anonymous pages over all of
+			/*
+			 * We start by mapping anonymous pages over all of
 			 * guest-physical memory range.  This fills it with 0,
 			 * and ensures that the Guest won't be killed when it
-			 * tries to access it. */
+			 * tries to access it.
+			 */
 			guest_base = map_zeroed_pages(mem / getpagesize()
 						      + DEVICE_PAGES);
 			guest_limit = mem;
@@ -1714,8 +1949,10 @@ int main(int argc, char *argv[])
 			usage();
 		}
 	}
-	/* After the other arguments we expect memory and kernel image name,
-	 * followed by command line arguments for the kernel. */
+	/*
+	 * After the other arguments we expect memory and kernel image name,
+	 * followed by command line arguments for the kernel.
+	 */
 	if (optind + 2 > argc)
 		usage();
 
@@ -1733,20 +1970,26 @@ int main(int argc, char *argv[])
 	/* Map the initrd image if requested (at top of physical memory) */
 	if (initrd_name) {
 		initrd_size = load_initrd(initrd_name, mem);
-		/* These are the location in the Linux boot header where the
-		 * start and size of the initrd are expected to be found. */
+		/*
+		 * These are the location in the Linux boot header where the
+		 * start and size of the initrd are expected to be found.
+		 */
 		boot->hdr.ramdisk_image = mem - initrd_size;
 		boot->hdr.ramdisk_size = initrd_size;
 		/* The bootloader type 0xFF means "unknown"; that's OK. */
 		boot->hdr.type_of_loader = 0xFF;
 	}
 
-	/* The Linux boot header contains an "E820" memory map: ours is a
-	 * simple, single region. */
+	/*
+	 * The Linux boot header contains an "E820" memory map: ours is a
+	 * simple, single region.
+	 */
 	boot->e820_entries = 1;
 	boot->e820_map[0] = ((struct e820entry) { 0, mem, E820_RAM });
-	/* The boot header contains a command line pointer: we put the command
-	 * line after the boot header. */
+	/*
+	 * The boot header contains a command line pointer: we put the command
+	 * line after the boot header.
+	 */
 	boot->hdr.cmd_line_ptr = to_guest_phys(boot + 1);
 	/* We use a simple helper to copy the arguments separated by spaces. */
 	concat((char *)(boot + 1), argv+optind+2);
@@ -1760,11 +2003,13 @@ int main(int argc, char *argv[])
 	/* Tell the entry path not to try to reload segment registers. */
 	boot->hdr.loadflags |= KEEP_SEGMENTS;
 
-	/* We tell the kernel to initialize the Guest: this returns the open
-	 * /dev/lguest file descriptor. */
+	/*
+	 * We tell the kernel to initialize the Guest: this returns the open
+	 * /dev/lguest file descriptor.
+	 */
 	tell_kernel(start);
 
-	/* Ensure that we terminate if a child dies. */
+	/* Ensure that we terminate if a device-servicing child dies. */
 	signal(SIGCHLD, kill_launcher);
 
 	/* If we exit via err(), this kills all the threads, restores tty. */

Documentation/lockdep-design.txt

@@ -30,9 +30,9 @@ State
 The validator tracks lock-class usage history into 4n + 1 separate state bits:
 
 - 'ever held in STATE context'
-- 'ever head as readlock in STATE context'
-- 'ever head with STATE enabled'
-- 'ever head as readlock with STATE enabled'
+- 'ever held as readlock in STATE context'
+- 'ever held with STATE enabled'
+- 'ever held as readlock with STATE enabled'
 
 Where STATE can be either one of (kernel/lockdep_states.h)
  - hardirq

MAINTAINERS

@@ -155,10 +155,9 @@ S:	Maintained
 F:	drivers/net/r8169.c
 
 8250/16?50 (AND CLONE UARTS) SERIAL DRIVER
-M:	Alan Cox <alan@lxorguk.ukuu.org.uk>
 L:	linux-serial@vger.kernel.org
 W:	http://serial.sourceforge.net
-S:	Odd Fixes
+S:	Orphan
 F:	drivers/serial/8250*
 F:	include/linux/serial_8250.h
 
@@ -3421,8 +3420,7 @@ S:	Supported
 F:	drivers/mfd/
 
 MULTIMEDIA CARD (MMC), SECURE DIGITAL (SD) AND SDIO SUBSYSTEM
-M:	Pierre Ossman <pierre@ossman.eu>
-S:	Maintained
+S:	Orphan
 F:	drivers/mmc/
 F:	include/linux/mmc/
 
@@ -4997,9 +4995,9 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial.git
 S:	Maintained
 
 TTY LAYER
-M:	Alan Cox <alan@lxorguk.ukuu.org.uk>
+M:	Greg Kroah-Hartman <gregkh@suse.de>
 S:	Maintained
-T:	stgit http://zeniv.linux.org.uk/~alan/ttydev/
+T:	quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/
 F:	drivers/char/tty_*
 F:	drivers/serial/serial_core.c
 F:	include/linux/serial_core.h

Makefile

@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 31
-EXTRAVERSION = -rc4
+EXTRAVERSION = -rc6
 NAME = Man-Eating Seals of Antiquity
 
 # *DOCUMENTATION*

arch/arm/boot/compressed/misc.c

@@ -29,7 +29,6 @@ unsigned int __machine_arch_type;
 
 static void putstr(const char *ptr);
 
-#include <linux/compiler.h>
 #include <mach/uncompress.h>
 
 #ifdef CONFIG_DEBUG_ICEDCC

arch/arm/common/clkdev.c

@@ -17,6 +17,7 @@
 #include <linux/err.h>
 #include <linux/string.h>
 #include <linux/mutex.h>
+#include <linux/clk.h>
 
 #include <asm/clkdev.h>
 #include <mach/clkdev.h>

arch/arm/configs/mx27_defconfig

@@ -1,15 +1,15 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc1
-# Wed Apr  8 10:18:06 2009
+# Linux kernel version: 2.6.31-rc4
+# Fri Jul 24 16:08:06 2009
 #
 CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
 CONFIG_GENERIC_GPIO=y
 CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
 CONFIG_GENERIC_HARDIRQS=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
@@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_HARDIRQS_SW_RESEND=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
 CONFIG_GENERIC_HWEIGHT=y
 CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_ARCH_MTD_XIP=y
 CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_VECTORS_BASE=0xffff0000
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -85,7 +84,12 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+
+#
+# Performance Counters
+#
 CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_COMPAT_BRK is not set
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -99,6 +103,12 @@ CONFIG_KPROBES=y
 CONFIG_KRETPROBES=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 CONFIG_HAVE_GENERIC_DMA_COHERENT=y
 CONFIG_SLABINFO=y
@@ -111,7 +121,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -138,13 +148,14 @@ CONFIG_FREEZER=y
 # CONFIG_ARCH_VERSATILE is not set
 # CONFIG_ARCH_AT91 is not set
 # CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
 # CONFIG_ARCH_EBSA110 is not set
 # CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_GEMINI is not set
 # CONFIG_ARCH_FOOTBRIDGE is not set
+CONFIG_ARCH_MXC=y
+# CONFIG_ARCH_STMP3XXX is not set
 # CONFIG_ARCH_NETX is not set
 # CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
 # CONFIG_ARCH_IOP13XX is not set
 # CONFIG_ARCH_IOP32X is not set
 # CONFIG_ARCH_IOP33X is not set
@@ -153,25 +164,25 @@ CONFIG_FREEZER=y
 # CONFIG_ARCH_IXP4XX is not set
 # CONFIG_ARCH_L7200 is not set
 # CONFIG_ARCH_KIRKWOOD is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
 # CONFIG_ARCH_LOKI is not set
 # CONFIG_ARCH_MV78XX0 is not set
-CONFIG_ARCH_MXC=y
 # CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
 # CONFIG_ARCH_PNX4008 is not set
 # CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_MSM is not set
 # CONFIG_ARCH_RPC is not set
 # CONFIG_ARCH_SA1100 is not set
 # CONFIG_ARCH_S3C2410 is not set
 # CONFIG_ARCH_S3C64XX is not set
 # CONFIG_ARCH_SHARK is not set
 # CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
 # CONFIG_ARCH_DAVINCI is not set
 # CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM is not set
-# CONFIG_ARCH_W90X900 is not set
 
 #
 # Freescale MXC Implementations
@@ -188,6 +199,8 @@ CONFIG_MACH_MX27=y
 CONFIG_MACH_MX27ADS=y
 CONFIG_MACH_PCM038=y
 CONFIG_MACH_PCM970_BASEBOARD=y
+CONFIG_MACH_MX27_3DS=y
+CONFIG_MACH_MX27LITE=y
 CONFIG_MXC_IRQ_PRIOR=y
 CONFIG_MXC_PWM=y
 
@@ -213,7 +226,6 @@ CONFIG_ARM_THUMB=y
 # CONFIG_CPU_DCACHE_DISABLE is not set
 # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
 # CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-# CONFIG_OUTER_CACHE is not set
 CONFIG_COMMON_CLKDEV=y
 
 #
@@ -238,7 +250,6 @@ CONFIG_PREEMPT=y
 CONFIG_HZ=100
 CONFIG_AEABI=y
 CONFIG_OABI_COMPAT=y
-CONFIG_ARCH_FLATMEM_HAS_HOLES=y
 # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
 # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
 # CONFIG_HIGHMEM is not set
@@ -253,10 +264,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4096
 # CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
 
 #
 # Boot options
@@ -361,6 +373,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -474,7 +487,16 @@ CONFIG_MTD_PHYSMAP=y
 # CONFIG_MTD_DOC2000 is not set
 # CONFIG_MTD_DOC2001 is not set
 # CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_NAND is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+CONFIG_MTD_NAND_MXC=y
 # CONFIG_MTD_ONENAND is not set
 
 #
@@ -485,7 +507,15 @@ CONFIG_MTD_PHYSMAP=y
 #
 # UBI - Unsorted block images
 #
-# CONFIG_MTD_UBI is not set
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_COW_COMMON is not set
@@ -494,7 +524,21 @@ CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_RAM is not set
 # CONFIG_CDROM_PKTCDVD is not set
 # CONFIG_ATA_OVER_ETH is not set
-# CONFIG_MISC_DEVICES is not set
+# CONFIG_MG_DISK is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -508,7 +552,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_ATA is not set
 # CONFIG_MD is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -534,6 +577,8 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
 CONFIG_FEC=y
 # CONFIG_FEC2 is not set
 # CONFIG_NETDEV_1000 is not set
@@ -580,6 +625,11 @@ CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_TABLET is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 # CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
 # CONFIG_TOUCHSCREEN_FUJITSU is not set
 # CONFIG_TOUCHSCREEN_GUNZE is not set
 # CONFIG_TOUCHSCREEN_ELO is not set
@@ -592,6 +642,7 @@ CONFIG_INPUT_TOUCHSCREEN=y
 # CONFIG_TOUCHSCREEN_TOUCHWIN is not set
 # CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
 # CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
 # CONFIG_INPUT_MISC is not set
 
 #
@@ -644,6 +695,7 @@ CONFIG_I2C_HELPER_AUTO=y
 #
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 CONFIG_I2C_IMX=y
 # CONFIG_I2C_OCORES is not set
@@ -668,7 +720,6 @@ CONFIG_I2C_IMX=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -719,6 +770,7 @@ CONFIG_W1=y
 #
 # CONFIG_W1_MASTER_DS2482 is not set
 CONFIG_W1_MASTER_MXC=y
+# CONFIG_W1_MASTER_DS1WM is not set
 # CONFIG_W1_MASTER_GPIO is not set
 
 #
@@ -753,54 +805,16 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_TPS65010 is not set
 # CONFIG_TWL4030_CORE is not set
 # CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
 # CONFIG_MFD_TC6393XB is not set
 # CONFIG_PMIC_DA903X is not set
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-CONFIG_VIDEO_DEV=y
-CONFIG_VIDEO_V4L2_COMMON=y
-CONFIG_VIDEO_ALLOW_V4L1=y
-CONFIG_VIDEO_V4L1_COMPAT=y
-# CONFIG_DVB_CORE is not set
-CONFIG_VIDEO_MEDIA=y
-
-#
-# Multimedia drivers
-#
-# CONFIG_MEDIA_ATTACH is not set
-CONFIG_MEDIA_TUNER=y
-# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
-CONFIG_MEDIA_TUNER_SIMPLE=y
-CONFIG_MEDIA_TUNER_TDA8290=y
-CONFIG_MEDIA_TUNER_TDA9887=y
-CONFIG_MEDIA_TUNER_TEA5761=y
-CONFIG_MEDIA_TUNER_TEA5767=y
-CONFIG_MEDIA_TUNER_MT20XX=y
-CONFIG_MEDIA_TUNER_XC2028=y
-CONFIG_MEDIA_TUNER_XC5000=y
-CONFIG_MEDIA_TUNER_MC44S803=y
-CONFIG_VIDEO_V4L2=y
-CONFIG_VIDEO_V4L1=y
-CONFIG_VIDEO_CAPTURE_DRIVERS=y
-# CONFIG_VIDEO_ADV_DEBUG is not set
-# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
-CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
-# CONFIG_VIDEO_VIVI is not set
-# CONFIG_VIDEO_CPIA is not set
-# CONFIG_VIDEO_SAA5246A is not set
-# CONFIG_VIDEO_SAA5249 is not set
-# CONFIG_SOC_CAMERA is not set
-# CONFIG_RADIO_ADAPTERS is not set
-# CONFIG_DAB is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -917,6 +931,7 @@ CONFIG_RTC_DRV_PCF8563=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -962,12 +977,15 @@ CONFIG_RTC_DRV_PCF8563=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
 # CONFIG_QUOTA is not set
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set
@@ -1021,6 +1039,12 @@ CONFIG_JFFS2_ZLIB=y
 # CONFIG_JFFS2_LZO is not set
 CONFIG_JFFS2_RTIME=y
 # CONFIG_JFFS2_RUBIN is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_XATTR is not set
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
 # CONFIG_CRAMFS is not set
 # CONFIG_SQUASHFS is not set
 # CONFIG_VXFS_FS is not set
@@ -1119,25 +1143,11 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y
 CONFIG_NOP_TRACER=y
 CONFIG_HAVE_FUNCTION_TRACER=y
 CONFIG_RING_BUFFER=y
+CONFIG_EVENT_TRACING=y
+CONFIG_CONTEXT_SWITCH_TRACER=y
 CONFIG_TRACING=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_IRQSOFF_TRACER is not set
-# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_FTRACE is not set
 # CONFIG_DYNAMIC_DEBUG is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
@@ -1151,16 +1161,104 @@ CONFIG_ARM_UNWIND=y
 # CONFIG_SECURITY is not set
 # CONFIG_SECURITYFS is not set
 # CONFIG_SECURITY_FILE_CAPABILITIES is not set
-# CONFIG_CRYPTO is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=y
+# CONFIG_CRYPTO_ZLIB is not set
+CONFIG_CRYPTO_LZO=y
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_HW=y
 CONFIG_BINARY_PRINTF=y
 
 #
 # Library routines
 #
 CONFIG_BITREVERSE=y
+CONFIG_RATIONAL=y
 CONFIG_GENERIC_FIND_LAST_BIT=y
 # CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
+CONFIG_CRC16=y
 # CONFIG_CRC_T10DIF is not set
 # CONFIG_CRC_ITU_T is not set
 CONFIG_CRC32=y
@@ -1168,6 +1266,8 @@ CONFIG_CRC32=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y

arch/arm/configs/mx3_defconfig

@@ -1,15 +1,15 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc1
-# Wed Apr  8 11:06:37 2009
+# Linux kernel version: 2.6.31-rc4
+# Tue Jul 28 14:11:34 2009
 #
 CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
 CONFIG_GENERIC_GPIO=y
 CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
 CONFIG_GENERIC_HARDIRQS=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
@@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_HARDIRQS_SW_RESEND=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
 CONFIG_GENERIC_HWEIGHT=y
 CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_ARCH_MTD_XIP=y
 CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_VECTORS_BASE=0xffff0000
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -86,7 +85,12 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+
+#
+# Performance Counters
+#
 CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -97,6 +101,11 @@ CONFIG_HAVE_OPROFILE=y
 # CONFIG_KPROBES is not set
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 CONFIG_HAVE_GENERIC_DMA_COHERENT=y
 CONFIG_SLABINFO=y
@@ -109,7 +118,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -136,13 +145,14 @@ CONFIG_FREEZER=y
 # CONFIG_ARCH_VERSATILE is not set
 # CONFIG_ARCH_AT91 is not set
 # CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
 # CONFIG_ARCH_EBSA110 is not set
 # CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_GEMINI is not set
 # CONFIG_ARCH_FOOTBRIDGE is not set
+CONFIG_ARCH_MXC=y
+# CONFIG_ARCH_STMP3XXX is not set
 # CONFIG_ARCH_NETX is not set
 # CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
 # CONFIG_ARCH_IOP13XX is not set
 # CONFIG_ARCH_IOP32X is not set
 # CONFIG_ARCH_IOP33X is not set
@@ -151,25 +161,25 @@ CONFIG_FREEZER=y
 # CONFIG_ARCH_IXP4XX is not set
 # CONFIG_ARCH_L7200 is not set
 # CONFIG_ARCH_KIRKWOOD is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
 # CONFIG_ARCH_LOKI is not set
 # CONFIG_ARCH_MV78XX0 is not set
-CONFIG_ARCH_MXC=y
 # CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
 # CONFIG_ARCH_PNX4008 is not set
 # CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_MSM is not set
 # CONFIG_ARCH_RPC is not set
 # CONFIG_ARCH_SA1100 is not set
 # CONFIG_ARCH_S3C2410 is not set
 # CONFIG_ARCH_S3C64XX is not set
 # CONFIG_ARCH_SHARK is not set
 # CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
 # CONFIG_ARCH_DAVINCI is not set
 # CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM is not set
-# CONFIG_ARCH_W90X900 is not set
 
 #
 # Freescale MXC Implementations
@@ -178,6 +188,7 @@ CONFIG_ARCH_MXC=y
 # CONFIG_ARCH_MX2 is not set
 CONFIG_ARCH_MX3=y
 CONFIG_ARCH_MX31=y
+CONFIG_ARCH_MX35=y
 
 #
 # MX3 platforms:
@@ -185,12 +196,19 @@ CONFIG_ARCH_MX31=y
 CONFIG_MACH_MX31ADS=y
 CONFIG_MACH_MX31ADS_WM1133_EV1=y
 CONFIG_MACH_PCM037=y
+CONFIG_MACH_PCM037_EET=y
 CONFIG_MACH_MX31LITE=y
 CONFIG_MACH_MX31_3DS=y
 CONFIG_MACH_MX31MOBOARD=y
+CONFIG_MACH_MX31LILLY=y
 CONFIG_MACH_QONG=y
+CONFIG_MACH_PCM043=y
+CONFIG_MACH_ARMADILLO5X0=y
+CONFIG_MACH_MX35_3DS=y
 CONFIG_MXC_IRQ_PRIOR=y
 CONFIG_MXC_PWM=y
+CONFIG_ARCH_HAS_RNGA=y
+CONFIG_ARCH_MXC_IOMUX_V3=y
 
 #
 # Processor Type
@@ -218,6 +236,7 @@ CONFIG_ARM_THUMB=y
 # CONFIG_CPU_BPREDICT_DISABLE is not set
 CONFIG_OUTER_CACHE=y
 CONFIG_CACHE_L2X0=y
+# CONFIG_ARM_ERRATA_411920 is not set
 CONFIG_COMMON_CLKDEV=y
 
 #
@@ -242,7 +261,6 @@ CONFIG_PREEMPT=y
 CONFIG_HZ=100
 CONFIG_AEABI=y
 CONFIG_OABI_COMPAT=y
-CONFIG_ARCH_FLATMEM_HAS_HOLES=y
 # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
 # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
 # CONFIG_HIGHMEM is not set
@@ -257,10 +275,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
 
 #
 # Boot options
@@ -362,6 +381,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -465,7 +485,16 @@ CONFIG_MTD_PHYSMAP=y
 # CONFIG_MTD_DOC2000 is not set
 # CONFIG_MTD_DOC2001 is not set
 # CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_NAND is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+CONFIG_MTD_NAND_MXC=y
 # CONFIG_MTD_ONENAND is not set
 
 #
@@ -476,10 +505,30 @@ CONFIG_MTD_PHYSMAP=y
 #
 # UBI - Unsorted block images
 #
-# CONFIG_MTD_UBI is not set
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
 # CONFIG_PARPORT is not set
 # CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -493,7 +542,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_ATA is not set
 # CONFIG_MD is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -528,7 +576,7 @@ CONFIG_MII=y
 # CONFIG_ETHOC is not set
 # CONFIG_SMC911X is not set
 CONFIG_SMSC911X=y
-# CONFIG_DNET is not set
+CONFIG_DNET=y
 # CONFIG_IBM_NEW_EMAC_ZMII is not set
 # CONFIG_IBM_NEW_EMAC_RGMII is not set
 # CONFIG_IBM_NEW_EMAC_TAH is not set
@@ -537,8 +585,10 @@ CONFIG_SMSC911X=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
-CONFIG_CS89x0=y
-CONFIG_CS89x0_NONISA_IRQ=y
+# CONFIG_CS89x0 is not set
+# CONFIG_KS8842 is not set
+CONFIG_FEC=y
+# CONFIG_FEC2 is not set
 # CONFIG_NETDEV_1000 is not set
 # CONFIG_NETDEV_10000 is not set
 
@@ -609,6 +659,7 @@ CONFIG_I2C_HELPER_AUTO=y
 #
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 CONFIG_I2C_IMX=y
 # CONFIG_I2C_OCORES is not set
@@ -633,7 +684,6 @@ CONFIG_I2C_IMX=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -669,6 +719,7 @@ CONFIG_W1=y
 #
 # CONFIG_W1_MASTER_DS2482 is not set
 CONFIG_W1_MASTER_MXC=y
+# CONFIG_W1_MASTER_DS1WM is not set
 # CONFIG_W1_MASTER_GPIO is not set
 
 #
@@ -703,6 +754,8 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_TPS65010 is not set
 # CONFIG_TWL4030_CORE is not set
 # CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
 # CONFIG_MFD_TC6393XB is not set
 # CONFIG_PMIC_DA903X is not set
 # CONFIG_MFD_WM8400 is not set
@@ -711,10 +764,8 @@ CONFIG_MFD_WM8350_CONFIG_MODE_0=y
 CONFIG_MFD_WM8352_CONFIG_MODE_0=y
 CONFIG_MFD_WM8350_I2C=y
 # CONFIG_MFD_PCF50633 is not set
-
-#
-# Multimedia devices
-#
+# CONFIG_AB3100_CORE is not set
+CONFIG_MEDIA_SUPPORT=y
 
 #
 # Multimedia core support
@@ -758,8 +809,10 @@ CONFIG_SOC_CAMERA_MT9T031=y
 CONFIG_SOC_CAMERA_MT9V022=y
 CONFIG_SOC_CAMERA_TW9910=y
 # CONFIG_SOC_CAMERA_PLATFORM is not set
-# CONFIG_SOC_CAMERA_OV772X is not set
+CONFIG_SOC_CAMERA_OV772X=y
+CONFIG_MX3_VIDEO=y
 CONFIG_VIDEO_MX3=y
+# CONFIG_VIDEO_SH_MOBILE_CEU is not set
 # CONFIG_RADIO_ADAPTERS is not set
 # CONFIG_DAB is not set
 
@@ -847,8 +900,11 @@ CONFIG_REGULATOR=y
 # CONFIG_REGULATOR_DEBUG is not set
 # CONFIG_REGULATOR_FIXED_VOLTAGE is not set
 # CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
 # CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
 CONFIG_REGULATOR_WM8350=y
+# CONFIG_REGULATOR_LP3971 is not set
 # CONFIG_UIO is not set
 # CONFIG_STAGING is not set
 
@@ -861,10 +917,12 @@ CONFIG_REGULATOR_WM8350=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -921,6 +979,12 @@ CONFIG_JFFS2_ZLIB=y
 # CONFIG_JFFS2_LZO is not set
 CONFIG_JFFS2_RTIME=y
 # CONFIG_JFFS2_RUBIN is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_XATTR is not set
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
 # CONFIG_CRAMFS is not set
 # CONFIG_SQUASHFS is not set
 # CONFIG_VXFS_FS is not set
@@ -937,6 +1001,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -979,22 +1044,7 @@ CONFIG_FRAME_WARN=1024
 CONFIG_SYSCTL_SYSCALL_CHECK=y
 CONFIG_HAVE_FUNCTION_TRACER=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_IRQSOFF_TRACER is not set
-# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 CONFIG_ARM_UNWIND=y
@@ -1094,9 +1144,9 @@ CONFIG_CRYPTO_DES=y
 #
 # Compression
 #
-# CONFIG_CRYPTO_DEFLATE is not set
+CONFIG_CRYPTO_DEFLATE=y
 # CONFIG_CRYPTO_ZLIB is not set
-# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_LZO=y
 
 #
 # Random Number Generation
@@ -1109,9 +1159,10 @@ CONFIG_CRYPTO_HW=y
 # Library routines
 #
 CONFIG_BITREVERSE=y
+CONFIG_RATIONAL=y
 CONFIG_GENERIC_FIND_LAST_BIT=y
 # CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
+CONFIG_CRC16=y
 # CONFIG_CRC_T10DIF is not set
 # CONFIG_CRC_ITU_T is not set
 CONFIG_CRC32=y
@@ -1119,6 +1170,8 @@ CONFIG_CRC32=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y

arch/arm/configs/omap3_evm_defconfig

@@ -1107,7 +1107,7 @@ CONFIG_USB_ZERO=m
 CONFIG_USB_OTG_UTILS=y
 # CONFIG_USB_GPIO_VBUS is not set
 # CONFIG_ISP1301_OMAP is not set
-CONFIG_TWL4030_USB=y
+# CONFIG_TWL4030_USB is not set
 # CONFIG_NOP_USB_XCEIV is not set
 CONFIG_MMC=y
 # CONFIG_MMC_DEBUG is not set

arch/arm/include/asm/atomic.h

@@ -159,8 +159,6 @@ static inline void atomic_clear_mask(unsigned long mask, unsigned long *addr)
 
 #else /* ARM_ARCH_6 */
 
-#include <asm/system.h>
-
 #ifdef CONFIG_SMP
 #error SMP not supported on pre-ARMv6 CPUs
 #endif

arch/arm/kernel/entry-common.S

@@ -148,7 +148,7 @@ trace:
 	sub r0, r0, #MCOUNT_INSN_SIZE
 	mov lr, pc
 	mov pc, r2
-	mov lr, r1				@ restore lr
+	ldr lr, [fp, #-4]			@ restore lr
 	ldmia sp!, {r0-r3, pc}
 
 #endif /* CONFIG_DYNAMIC_FTRACE */

arch/arm/kernel/signal.c

@@ -133,7 +133,7 @@ sys_sigaction(int sig, const struct old_sigaction __user *act,
 }
 
 #ifdef CONFIG_CRUNCH
-static int preserve_crunch_context(struct crunch_sigframe *frame)
+static int preserve_crunch_context(struct crunch_sigframe __user *frame)
 {
 	char kbuf[sizeof(*frame) + 8];
 	struct crunch_sigframe *kframe;
@@ -146,7 +146,7 @@ static int preserve_crunch_context(struct crunch_sigframe *frame)
 	return __copy_to_user(frame, kframe, sizeof(*frame));
 }
 
-static int restore_crunch_context(struct crunch_sigframe *frame)
+static int restore_crunch_context(struct crunch_sigframe __user *frame)
 {
 	char kbuf[sizeof(*frame) + 8];
 	struct crunch_sigframe *kframe;

arch/arm/mach-at91/include/mach/at_hdmac.h

@@ -0,0 +1,102 @@
+/*
+ * Header file for the Atmel AHB DMA Controller driver
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef AT_HDMAC_H
+#define AT_HDMAC_H
+
+#include <linux/dmaengine.h>
+
+/**
+ * struct at_dma_platform_data - Controller configuration parameters
+ * @nr_channels: Number of channels supported by hardware (max 8)
+ * @cap_mask: dma_capability flags supported by the platform
+ */
+struct at_dma_platform_data {
+	unsigned int	nr_channels;
+	dma_cap_mask_t  cap_mask;
+};
+
+/**
+ * enum at_dma_slave_width - DMA slave register access width.
+ * @AT_DMA_SLAVE_WIDTH_8BIT: Do 8-bit slave register accesses
+ * @AT_DMA_SLAVE_WIDTH_16BIT: Do 16-bit slave register accesses
+ * @AT_DMA_SLAVE_WIDTH_32BIT: Do 32-bit slave register accesses
+ */
+enum at_dma_slave_width {
+	AT_DMA_SLAVE_WIDTH_8BIT = 0,
+	AT_DMA_SLAVE_WIDTH_16BIT,
+	AT_DMA_SLAVE_WIDTH_32BIT,
+};
+
+/**
+ * struct at_dma_slave - Controller-specific information about a slave
+ * @dma_dev: required DMA master device
+ * @tx_reg: physical address of data register used for
+ *	memory-to-peripheral transfers
+ * @rx_reg: physical address of data register used for
+ *	peripheral-to-memory transfers
+ * @reg_width: peripheral register width
+ * @cfg: Platform-specific initializer for the CFG register
+ * @ctrla: Platform-specific initializer for the CTRLA register
+ */
+struct at_dma_slave {
+	struct device		*dma_dev;
+	dma_addr_t		tx_reg;
+	dma_addr_t		rx_reg;
+	enum at_dma_slave_width	reg_width;
+	u32			cfg;
+	u32			ctrla;
+};
+
+
+/* Platform-configurable bits in CFG */
+#define	ATC_SRC_PER(h)		(0xFU & (h))	/* Channel src rq associated with periph handshaking ifc h */
+#define	ATC_DST_PER(h)		((0xFU & (h)) <<  4)	/* Channel dst rq associated with periph handshaking ifc h */
+#define	ATC_SRC_REP		(0x1 <<  8)	/* Source Replay Mod */
+#define	ATC_SRC_H2SEL		(0x1 <<  9)	/* Source Handshaking Mod */
+#define		ATC_SRC_H2SEL_SW	(0x0 <<  9)
+#define		ATC_SRC_H2SEL_HW	(0x1 <<  9)
+#define	ATC_DST_REP		(0x1 << 12)	/* Destination Replay Mod */
+#define	ATC_DST_H2SEL		(0x1 << 13)	/* Destination Handshaking Mod */
+#define		ATC_DST_H2SEL_SW	(0x0 << 13)
+#define		ATC_DST_H2SEL_HW	(0x1 << 13)
+#define	ATC_SOD			(0x1 << 16)	/* Stop On Done */
+#define	ATC_LOCK_IF		(0x1 << 20)	/* Interface Lock */
+#define	ATC_LOCK_B		(0x1 << 21)	/* AHB Bus Lock */
+#define	ATC_LOCK_IF_L		(0x1 << 22)	/* Master Interface Arbiter Lock */
+#define		ATC_LOCK_IF_L_CHUNK	(0x0 << 22)
+#define		ATC_LOCK_IF_L_BUFFER	(0x1 << 22)
+#define	ATC_AHB_PROT_MASK	(0x7 << 24)	/* AHB Protection */
+#define	ATC_FIFOCFG_MASK	(0x3 << 28)	/* FIFO Request Configuration */
+#define		ATC_FIFOCFG_LARGESTBURST	(0x0 << 28)
+#define		ATC_FIFOCFG_HALFFIFO		(0x1 << 28)
+#define		ATC_FIFOCFG_ENOUGHSPACE		(0x2 << 28)
+
+/* Platform-configurable bits in CTRLA */
+#define	ATC_SCSIZE_MASK		(0x7 << 16)	/* Source Chunk Transfer Size */
+#define		ATC_SCSIZE_1		(0x0 << 16)
+#define		ATC_SCSIZE_4		(0x1 << 16)
+#define		ATC_SCSIZE_8		(0x2 << 16)
+#define		ATC_SCSIZE_16		(0x3 << 16)
+#define		ATC_SCSIZE_32		(0x4 << 16)
+#define		ATC_SCSIZE_64		(0x5 << 16)
+#define		ATC_SCSIZE_128		(0x6 << 16)
+#define		ATC_SCSIZE_256		(0x7 << 16)
+#define	ATC_DCSIZE_MASK		(0x7 << 20)	/* Destination Chunk Transfer Size */
+#define		ATC_DCSIZE_1		(0x0 << 20)
+#define		ATC_DCSIZE_4		(0x1 << 20)
+#define		ATC_DCSIZE_8		(0x2 << 20)
+#define		ATC_DCSIZE_16		(0x3 << 20)
+#define		ATC_DCSIZE_32		(0x4 << 20)
+#define		ATC_DCSIZE_64		(0x5 << 20)
+#define		ATC_DCSIZE_128		(0x6 << 20)
+#define		ATC_DCSIZE_256		(0x7 << 20)
+
+#endif /* AT_HDMAC_H */

arch/arm/mach-davinci/board-dm355-evm.c

@@ -37,7 +37,6 @@
 #include <mach/serial.h>
 #include <mach/nand.h>
 #include <mach/mmc.h>
-#include <mach/common.h>
 
 #define DAVINCI_ASYNC_EMIF_CONTROL_BASE		0x01e10000
 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE	0x02000000

arch/arm/mach-davinci/board-dm355-leopard.c

@@ -36,7 +36,6 @@
 #include <mach/serial.h>
 #include <mach/nand.h>
 #include <mach/mmc.h>
-#include <mach/common.h>
 
 #define DAVINCI_ASYNC_EMIF_CONTROL_BASE		0x01e10000
 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE	0x02000000

arch/arm/mach-davinci/board-dm644x-evm.c

@@ -45,7 +45,6 @@
 #include <mach/nand.h>
 #include <mach/mmc.h>
 #include <mach/emac.h>
-#include <mach/common.h>
 
 #define DM644X_EVM_PHY_MASK		(0x2)
 #define DM644X_EVM_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */

arch/arm/mach-davinci/board-dm646x-evm.c

@@ -47,7 +47,6 @@
 #include <mach/i2c.h>
 #include <mach/mmc.h>
 #include <mach/emac.h>
-#include <mach/common.h>
 
 #define DM646X_EVM_PHY_MASK		(0x2)
 #define DM646X_EVM_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */

arch/arm/mach-davinci/board-sffsdr.c

@@ -52,7 +52,6 @@
 #include <mach/serial.h>
 #include <mach/psc.h>
 #include <mach/mux.h>
-#include <mach/common.h>
 
 #define SFFSDR_PHY_MASK		(0x2)
 #define SFFSDR_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */

arch/arm/mach-ep93xx/include/mach/ts72xx.h

@@ -41,9 +41,6 @@
 #define TS72XX_OPTIONS2_TS9420_BOOT	0x02
 
 
-#define TS72XX_NOR_PHYS_BASE		0x60000000
-#define TS72XX_NOR2_PHYS_BASE		0x62000000
-
 #define TS72XX_NAND1_DATA_PHYS_BASE	0x60000000
 #define TS72XX_NAND2_DATA_PHYS_BASE	0x70000000
 #define TS72XX_NAND_DATA_VIRT_BASE	0xfebfc000

arch/arm/mach-ep93xx/ts72xx.c

@@ -112,13 +112,16 @@ static void __init ts72xx_map_io(void)
 	}
 }
 
+/*************************************************************************
+ * NOR flash (TS-7200 only)
+ *************************************************************************/
 static struct physmap_flash_data ts72xx_flash_data = {
-	.width		= 1,
+	.width		= 2,
 };
 
 static struct resource ts72xx_flash_resource = {
-	.start		= TS72XX_NOR_PHYS_BASE,
-	.end		= TS72XX_NOR_PHYS_BASE + SZ_16M - 1,
+	.start		= EP93XX_CS6_PHYS_BASE,
+	.end		= EP93XX_CS6_PHYS_BASE + SZ_16M - 1,
 	.flags		= IORESOURCE_MEM,
 };
 
@@ -132,6 +135,12 @@ static struct platform_device ts72xx_flash = {
 	.resource	= &ts72xx_flash_resource,
 };
 
+static void __init ts72xx_register_flash(void)
+{
+	if (board_is_ts7200())
+		platform_device_register(&ts72xx_flash);
+}
+
 static unsigned char ts72xx_rtc_readbyte(unsigned long addr)
 {
 	__raw_writeb(addr, TS72XX_RTC_INDEX_VIRT_BASE);
@@ -165,8 +174,7 @@ static struct ep93xx_eth_data ts72xx_eth_data = {
 static void __init ts72xx_init_machine(void)
 {
 	ep93xx_init_devices();
-	if (board_is_ts7200())
-		platform_device_register(&ts72xx_flash);
+	ts72xx_register_flash();
 	platform_device_register(&ts72xx_rtc_device);
 
 	ep93xx_register_eth(&ts72xx_eth_data, 1);

arch/arm/mach-ks8695/include/mach/hardware.h

@@ -16,6 +16,11 @@
 
 #include <asm/sizes.h>
 
+/*
+ * Clocks are derived from MCLK, which is 25Mhz
+ */
+#define KS8695_CLOCK_RATE	25000000
+
 /*
  * Physical RAM address.
  */

arch/arm/mach-ks8695/include/mach/timex.h

@@ -14,7 +14,8 @@
 #ifndef __ASM_ARCH_TIMEX_H
 #define __ASM_ARCH_TIMEX_H
 
-/* timers are derived from MCLK, which is 25MHz */
-#define CLOCK_TICK_RATE 25000000
+#include <mach/hardware.h>
+
+#define CLOCK_TICK_RATE 	KS8695_CLOCK_RATE
 
 #endif

arch/arm/mach-ks8695/pci.c

@@ -245,6 +245,9 @@ static int ks8695_pci_fault(unsigned long addr, unsigned int fsr, struct pt_regs
 
 static void __init ks8695_pci_preinit(void)
 {
+	/* make software reset to avoid freeze if PCI bus was messed up */
+	__raw_writel(0x80000000, KS8695_PCI_VA + KS8695_PBCS);
+
 	/* stage 1 initialization, subid, subdevice = 0x0001 */
 	__raw_writel(0x00010001, KS8695_PCI_VA + KS8695_CRCSID);
 

arch/arm/mach-omap1/mcbsp.c

@@ -19,7 +19,6 @@
 
 #include <mach/irqs.h>
 #include <mach/dma.h>
-#include <mach/irqs.h>
 #include <mach/mux.h>
 #include <mach/cpu.h>
 #include <mach/mcbsp.h>

arch/arm/mach-omap2/board-omap3evm.c

@@ -25,6 +25,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
 #include <linux/i2c/twl4030.h>
+#include <linux/usb/otg.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -307,6 +308,10 @@ static void __init omap3_evm_init(void)
 				ARRAY_SIZE(omap3evm_spi_board_info));
 
 	omap_serial_init();
+#ifdef CONFIG_NOP_USB_XCEIV
+	/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
+	usb_nop_xceiv_register();
+#endif
 	usb_musb_init();
 	ads7846_dev_init();
 }

arch/arm/mach-omap2/mcbsp.c

@@ -19,7 +19,6 @@
 
 #include <mach/irqs.h>
 #include <mach/dma.h>
-#include <mach/irqs.h>
 #include <mach/mux.h>
 #include <mach/cpu.h>
 #include <mach/mcbsp.h>

arch/arm/mach-omap2/usb-musb.c

@@ -155,20 +155,6 @@ static struct platform_device musb_device = {
 	.resource	= musb_resources,
 };
 
-#ifdef CONFIG_NOP_USB_XCEIV
-static u64 nop_xceiv_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device nop_xceiv_device = {
-	.name		= "nop_usb_xceiv",
-	.id		= -1,
-	.dev = {
-		.dma_mask		= &nop_xceiv_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data		= NULL,
-	},
-};
-#endif
-
 void __init usb_musb_init(void)
 {
 	if (cpu_is_omap243x())
@@ -183,13 +169,6 @@ void __init usb_musb_init(void)
 	 */
 	musb_plat.clock = "ick";
 
-#ifdef CONFIG_NOP_USB_XCEIV
-	if (platform_device_register(&nop_xceiv_device) < 0) {
-		printk(KERN_ERR "Unable to register NOP-XCEIV device\n");
-		return;
-	}
-#endif
-
 	if (platform_device_register(&musb_device) < 0) {
 		printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n");
 		return;

arch/arm/mach-pxa/em-x270.c

@@ -1141,12 +1141,16 @@ struct power_supply_info em_x270_psy_info = {
 
 static void em_x270_battery_low(void)
 {
+#if defined(CONFIG_APM_EMULATION)
 	apm_queue_event(APM_LOW_BATTERY);
+#endif
 }
 
 static void em_x270_battery_critical(void)
 {
+#if defined(CONFIG_APM_EMULATION)
 	apm_queue_event(APM_CRITICAL_SUSPEND);
+#endif
 }
 
 struct da9030_battery_info em_x270_batterty_info = {

arch/arm/mach-pxa/palmld.c

@@ -128,6 +128,10 @@ static unsigned long palmld_pin_config[] __initdata = {
 	GPIO38_GPIO,	/* wifi ready */
 	GPIO81_GPIO,	/* wifi reset */
 
+	/* FFUART */
+	GPIO34_FFUART_RXD,
+	GPIO39_FFUART_TXD,
+
 	/* HDD */
 	GPIO98_GPIO,	/* HDD reset */
 	GPIO115_GPIO,	/* HDD power */

arch/arm/mach-pxa/palmt5.c

@@ -111,6 +111,10 @@ static unsigned long palmt5_pin_config[] __initdata = {
 	/* PWM */
 	GPIO16_PWM0_OUT,
 
+	/* FFUART */
+	GPIO34_FFUART_RXD,
+	GPIO39_FFUART_TXD,
+
 	/* MISC */
 	GPIO10_GPIO,	/* hotsync button */
 	GPIO90_GPIO,	/* power detect */

arch/arm/mach-pxa/palmtx.c

@@ -127,6 +127,10 @@ static unsigned long palmtx_pin_config[] __initdata = {
 	GPIO76_LCD_PCLK,
 	GPIO77_LCD_BIAS,
 
+	/* FFUART */
+	GPIO34_FFUART_RXD,
+	GPIO39_FFUART_TXD,
+
 	/* MISC. */
 	GPIO10_GPIO,	/* hotsync button */
 	GPIO12_GPIO,	/* power detect */

arch/arm/mach-pxa/treo680.c

@@ -409,7 +409,7 @@ err1:
 
 static void treo680_irda_shutdown(struct device *dev)
 {
-	gpio_free(GPIO_NR_TREO680_AMP_EN);
+	gpio_free(GPIO_NR_TREO680_IR_EN);
 }
 
 static struct pxaficp_platform_data treo680_ficp_info = {

arch/arm/mach-pxa/zylonite_pxa300.c

@@ -197,10 +197,12 @@ static void __init zylonite_detect_lcd_panel(void)
 	for (i = 0; i < NUM_LCD_DETECT_PINS; i++) {
 		id = id << 1;
 		gpio = mfp_to_gpio(lcd_detect_pins[i]);
+		gpio_request(gpio, "LCD_ID_PINS");
 		gpio_direction_input(gpio);
 
 		if (gpio_get_value(gpio))
 			id = id | 0x1;
+		gpio_free(gpio);
 	}
 
 	/* lcd id, flush out bit 1 */

arch/arm/mach-pxa/zylonite_pxa320.c

@@ -176,10 +176,12 @@ static void __init zylonite_detect_lcd_panel(void)
 	for (i = 0; i < NUM_LCD_DETECT_PINS; i++) {
 		id = id << 1;
 		gpio = mfp_to_gpio(lcd_detect_pins[i]);
+		gpio_request(gpio, "LCD_ID_PINS");
 		gpio_direction_input(gpio);
 
 		if (gpio_get_value(gpio))
 			id = id | 0x1;
+		gpio_free(gpio);
 	}
 
 	/* lcd id, flush out bit 1 */

arch/arm/mach-s3c2410/include/mach/gpio-core.h

@@ -28,7 +28,7 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin)
 		return NULL;
 
 	chip = &s3c24xx_gpios[pin/32];
-	return (S3C2410_GPIO_OFFSET(pin) > chip->chip.ngpio) ? chip : NULL;
+	return (S3C2410_GPIO_OFFSET(pin) < chip->chip.ngpio) ? chip : NULL;
 }
 
 #endif /* __ASM_ARCH_GPIO_CORE_H */

arch/arm/plat-s3c24xx/pwm.c

@@ -246,6 +246,10 @@ int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns)
 
 	tcmp = duty_ns / tin_ns;
 	tcmp = tcnt - tcmp;
+	/* the pwm hw only checks the compare register after a decrement,
+	   so the pin never toggles if tcmp = tcnt */
+	if (tcmp == tcnt)
+		tcmp--;
 
 	pwm_dbg(pwm, "tin_ns=%lu, tcmp=%ld/%lu\n", tin_ns, tcmp, tcnt);
 

arch/arm/plat-s3c64xx/pm.c

@@ -117,8 +117,6 @@ void s3c_pm_save_core(void)
  * this.
  */
 
-#include <plat/regs-gpio.h>
-
 static void s3c64xx_cpu_suspend(void)
 {
 	unsigned long tmp;

arch/arm/plat-s3c64xx/s3c6400-clock.c

@@ -153,7 +153,7 @@ static unsigned long s3c64xx_clk_arm_round_rate(struct clk *clk,
 	u32 div;
 
 	if (parent < rate)
-		return rate;
+		return parent;
 
 	div = (parent / rate) - 1;
 	if (div > armclk_mask)
@@ -175,7 +175,7 @@ static int s3c64xx_clk_arm_set_rate(struct clk *clk, unsigned long rate)
 	div = clk_get_rate(clk->parent) / rate;
 
 	val = __raw_readl(S3C_CLK_DIV0);
-	val &= armclk_mask;
+	val &= ~armclk_mask;
 	val |= (div - 1);
 	__raw_writel(val, S3C_CLK_DIV0);
 

arch/arm/plat-stmp3xxx/pinmux.c

@@ -22,7 +22,6 @@
 #include <linux/sysdev.h>
 #include <linux/string.h>
 #include <linux/bitops.h>
-#include <linux/sysdev.h>
 #include <linux/irq.h>
 
 #include <mach/hardware.h>

arch/ia64/Makefile

@@ -41,11 +41,6 @@ $(error Sorry, you need a newer version of the assember, one that is built from
 		ftp://ftp.hpl.hp.com/pub/linux-ia64/gas-030124.tar.gz)
 endif
 
-ifeq ($(call cc-version),0304)
-	cflags-$(CONFIG_ITANIUM)	+= -mtune=merced
-	cflags-$(CONFIG_MCKINLEY)	+= -mtune=mckinley
-endif
-
 KBUILD_CFLAGS += $(cflags-y)
 head-y := arch/ia64/kernel/head.o arch/ia64/kernel/init_task.o
 

arch/ia64/include/asm/bitops.h

@@ -286,7 +286,7 @@ __test_and_clear_bit(int nr, volatile void * addr)
 {
 	__u32 *p = (__u32 *) addr + (nr >> 5);
 	__u32 m = 1 << (nr & 31);
-	int oldbitset = *p & m;
+	int oldbitset = (*p & m) != 0;
 
 	*p &= ~m;
 	return oldbitset;

arch/ia64/include/asm/pgtable.h

@@ -155,7 +155,6 @@
 #include <linux/bitops.h>
 #include <asm/cacheflush.h>
 #include <asm/mmu_context.h>
-#include <asm/processor.h>
 
 /*
  * Next come the mappings that determine how mmap() protection bits

arch/ia64/kernel/ia64_ksyms.c

@@ -21,6 +21,7 @@ EXPORT_SYMBOL(csum_ipv6_magic);
 
 #include <asm/page.h>
 EXPORT_SYMBOL(clear_page);
+EXPORT_SYMBOL(copy_page);
 
 #ifdef CONFIG_VIRTUAL_MEM_MAP
 #include <linux/bootmem.h>
@@ -60,9 +61,6 @@ EXPORT_SYMBOL(__udivdi3);
 EXPORT_SYMBOL(__moddi3);
 EXPORT_SYMBOL(__umoddi3);
 
-#include <asm/page.h>
-EXPORT_SYMBOL(copy_page);
-
 #if defined(CONFIG_MD_RAID456) || defined(CONFIG_MD_RAID456_MODULE)
 extern void xor_ia64_2(void);
 extern void xor_ia64_3(void);

arch/ia64/kernel/iosapic.c

@@ -1072,6 +1072,10 @@ iosapic_init (unsigned long phys_addr, unsigned int gsi_base)
 	}
 
 	addr = ioremap(phys_addr, 0);
+	if (addr == NULL) {
+		spin_unlock_irqrestore(&iosapic_lock, flags);
+		return -ENOMEM;
+	}
 	ver = iosapic_version(addr);
 	if ((err = iosapic_check_gsi_range(gsi_base, ver))) {
 		iounmap(addr);

arch/ia64/kernel/pci-dma.c

@@ -69,11 +69,6 @@ iommu_dma_init(void)
 
 int iommu_dma_supported(struct device *dev, u64 mask)
 {
-	struct dma_map_ops *ops = platform_dma_get_ops(dev);
-
-	if (ops->dma_supported)
-		return ops->dma_supported(dev, mask);
-
 	/* Copied from i386. Doesn't make much sense, because it will
 	   only work for pci_alloc_coherent.
 	   The caller just has to use GFP_DMA in this case. */

arch/ia64/kernel/topology.c

@@ -372,6 +372,10 @@ static int __cpuinit cache_add_dev(struct sys_device * sys_dev)
 	retval = kobject_init_and_add(&all_cpu_cache_info[cpu].kobj,
 				      &cache_ktype_percpu_entry, &sys_dev->kobj,
 				      "%s", "cache");
+	if (unlikely(retval < 0)) {
+		cpu_cache_sysfs_exit(cpu);
+		return retval;
+	}
 
 	for (i = 0; i < all_cpu_cache_info[cpu].num_cache_leaves; i++) {
 		this_object = LEAF_KOBJECT_PTR(cpu,i);
@@ -385,7 +389,7 @@ static int __cpuinit cache_add_dev(struct sys_device * sys_dev)
 			}
 			kobject_put(&all_cpu_cache_info[cpu].kobj);
 			cpu_cache_sysfs_exit(cpu);
-			break;
+			return retval;
 		}
 		kobject_uevent(&(this_object->kobj), KOBJ_ADD);
 	}

arch/ia64/kvm/mmio.c

@@ -247,7 +247,8 @@ void emulate_io_inst(struct kvm_vcpu *vcpu, u64 padr, u64 ma)
 		vcpu_get_fpreg(vcpu, inst.M9.f2, &v);
 		/* Write high word. FIXME: this is a kludge!  */
 		v.u.bits[1] &= 0x3ffff;
-		mmio_access(vcpu, padr + 8, &v.u.bits[1], 8, ma, IOREQ_WRITE);
+		mmio_access(vcpu, padr + 8, (u64 *)&v.u.bits[1], 8,
+			    ma, IOREQ_WRITE);
 		data = v.u.bits[0];
 		size = 3;
 	} else if (inst.M10.major == 7 && inst.M10.x6 == 0x3B) {
@@ -265,7 +266,8 @@ void emulate_io_inst(struct kvm_vcpu *vcpu, u64 padr, u64 ma)
 
 		/* Write high word.FIXME: this is a kludge!  */
 		v.u.bits[1] &= 0x3ffff;
-		mmio_access(vcpu, padr + 8, &v.u.bits[1], 8, ma, IOREQ_WRITE);
+		mmio_access(vcpu, padr + 8, (u64 *)&v.u.bits[1],
+			    8, ma, IOREQ_WRITE);
 		data = v.u.bits[0];
 		size = 3;
 	} else if (inst.M10.major == 7 && inst.M10.x6 == 0x31) {

arch/ia64/kvm/vcpu.c

@@ -461,7 +461,7 @@ void setreg(unsigned long regnum, unsigned long val,
 u64 vcpu_get_gr(struct kvm_vcpu *vcpu, unsigned long reg)
 {
 	struct kvm_pt_regs *regs = vcpu_regs(vcpu);
-	u64 val;
+	unsigned long val;
 
 	if (!reg)
 		return 0;
@@ -469,7 +469,7 @@ u64 vcpu_get_gr(struct kvm_vcpu *vcpu, unsigned long reg)
 	return val;
 }
 
-void vcpu_set_gr(struct kvm_vcpu *vcpu, u64 reg, u64 value, int nat)
+void vcpu_set_gr(struct kvm_vcpu *vcpu, unsigned long reg, u64 value, int nat)
 {
 	struct kvm_pt_regs *regs = vcpu_regs(vcpu);
 	long sof = (regs->cr_ifs) & 0x7f;
@@ -1072,7 +1072,7 @@ void kvm_ttag(struct kvm_vcpu *vcpu, INST64 inst)
 	vcpu_set_gr(vcpu, inst.M46.r1, tag, 0);
 }
 
-int vcpu_tpa(struct kvm_vcpu *vcpu, u64 vadr, u64 *padr)
+int vcpu_tpa(struct kvm_vcpu *vcpu, u64 vadr, unsigned long *padr)
 {
 	struct thash_data *data;
 	union ia64_isr visr, pt_isr;

arch/ia64/kvm/vcpu.h

@@ -686,14 +686,15 @@ static inline int highest_inservice_irq(struct kvm_vcpu *vcpu)
 	return highest_bits((int *)&(VMX(vcpu, insvc[0])));
 }
 
-extern void vcpu_get_fpreg(struct kvm_vcpu *vcpu, u64 reg,
+extern void vcpu_get_fpreg(struct kvm_vcpu *vcpu, unsigned long reg,
 					struct ia64_fpreg *val);
-extern void vcpu_set_fpreg(struct kvm_vcpu *vcpu, u64 reg,
+extern void vcpu_set_fpreg(struct kvm_vcpu *vcpu, unsigned long reg,
 					struct ia64_fpreg *val);
-extern u64 vcpu_get_gr(struct kvm_vcpu *vcpu, u64 reg);
-extern void vcpu_set_gr(struct kvm_vcpu *vcpu, u64 reg, u64 val, int nat);
-extern u64 vcpu_get_psr(struct kvm_vcpu *vcpu);
-extern void vcpu_set_psr(struct kvm_vcpu *vcpu, u64 val);
+extern u64 vcpu_get_gr(struct kvm_vcpu *vcpu, unsigned long reg);
+extern void vcpu_set_gr(struct kvm_vcpu *vcpu, unsigned long reg,
+			u64 val, int nat);
+extern unsigned long vcpu_get_psr(struct kvm_vcpu *vcpu);
+extern void vcpu_set_psr(struct kvm_vcpu *vcpu, unsigned long val);
 extern u64 vcpu_thash(struct kvm_vcpu *vcpu, u64 vadr);
 extern void vcpu_bsw0(struct kvm_vcpu *vcpu);
 extern void thash_vhpt_insert(struct kvm_vcpu *v, u64 pte,

arch/mips/alchemy/mtx-1/platform.c

@@ -1,7 +1,7 @@
 /*
  * MTX-1 platform devices registration
  *
- * Copyright (C) 2007, Florian Fainelli <florian@openwrt.org>
+ * Copyright (C) 2007-2009, Florian Fainelli <florian@openwrt.org>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -142,7 +142,17 @@ static struct __initdata platform_device * mtx1_devs[] = {
 
 static int __init mtx1_register_devices(void)
 {
-	gpio_direction_input(207);
+	int rc;
+
+	rc = gpio_request(mtx1_gpio_button[0].gpio,
+					mtx1_gpio_button[0].desc);
+	if (rc < 0) {
+		printk(KERN_INFO "mtx1: failed to request %d\n",
+					mtx1_gpio_button[0].gpio);
+		goto out;
+	}
+	gpio_direction_input(mtx1_gpio_button[0].gpio);
+out:
 	return platform_add_devices(mtx1_devs, ARRAY_SIZE(mtx1_devs));
 }
 

arch/mips/ar7/Makefile

@@ -8,3 +8,4 @@ obj-y := \
 	platform.o \
 	gpio.o \
 	clock.o
+EXTRA_CFLAGS += -Werror

arch/mips/ar7/clock.c

@@ -264,19 +264,6 @@ static void __init tnetd7300_init_clocks(void)
 	iounmap(bootcr);
 }
 
-static int tnetd7200_get_clock(int base, struct tnetd7200_clock *clock,
-	u32 *bootcr, u32 bus_clock)
-{
-	int divisor = ((readl(&clock->prediv) & 0x1f) + 1) *
-		((readl(&clock->postdiv) & 0x1f) + 1);
-
-	if (*bootcr & BOOT_PLL_BYPASS)
-		return base / divisor;
-
-	return base * ((readl(&clock->mul) & 0xf) + 1) / divisor;
-}
-
-
 static void tnetd7200_set_clock(int base, struct tnetd7200_clock *clock,
 	int prediv, int postdiv, int postdiv2, int mul, u32 frequency)
 {

arch/mips/ar7/memory.c

@@ -52,7 +52,7 @@ static int __init memsize(void)
 		size <<= 1;
 	} while (size < (64 << 20));
 
-	writel(tmpaddr, &addr);
+	writel((u32)tmpaddr, &addr);
 
 	return size;
 }

arch/mips/ar7/platform.c

@@ -28,7 +28,6 @@
 #include <linux/serial_8250.h>
 #include <linux/ioport.h>
 #include <linux/io.h>
-#include <linux/version.h>
 #include <linux/vlynq.h>
 #include <linux/leds.h>
 #include <linux/string.h>
@@ -243,13 +242,13 @@ static struct platform_device physmap_flash = {
 	.num_resources = 1,
 };
 
-static u64 cpmac_dma_mask = DMA_32BIT_MASK;
+static u64 cpmac_dma_mask = DMA_BIT_MASK(32);
 static struct platform_device cpmac_low = {
 	.id = 0,
 	.name = "cpmac",
 	.dev = {
 		.dma_mask = &cpmac_dma_mask,
-		.coherent_dma_mask = DMA_32BIT_MASK,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
 		.platform_data = &cpmac_low_data,
 	},
 	.resource = cpmac_low_res,
@@ -261,7 +260,7 @@ static struct platform_device cpmac_high = {
 	.name = "cpmac",
 	.dev = {
 		.dma_mask = &cpmac_dma_mask,
-		.coherent_dma_mask = DMA_32BIT_MASK,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
 		.platform_data = &cpmac_high_data,
 	},
 	.resource = cpmac_high_res,
@@ -481,6 +480,7 @@ static void __init detect_leds(void)
 static int __init ar7_register_devices(void)
 {
 	int res;
+#ifdef CONFIG_SERIAL_8250
 	static struct uart_port uart_port[2];
 
 	memset(uart_port, 0, sizeof(struct uart_port) * 2);
@@ -512,7 +512,7 @@ static int __init ar7_register_devices(void)
 		if (res)
 			return res;
 	}
-
+#endif /* CONFIG_SERIAL_8250 */
 	res = platform_device_register(&physmap_flash);
 	if (res)
 		return res;

arch/mips/ar7/prom.c

@@ -144,7 +144,7 @@ static char * __init lookup_psp_var_map(u8 num)
 {
 	int i;
 
-	for (i = 0; i < sizeof(psp_var_map); i++)
+	for (i = 0; i < ARRAY_SIZE(psp_var_map); i++)
 		if (psp_var_map[i].num == num)
 			return psp_var_map[i].value;
 

arch/mips/ar7/setup.c

@@ -15,7 +15,6 @@
  *  with this program; if not, write to the Free Software Foundation, Inc.,
  *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
  */
-#include <linux/version.h>
 #include <linux/init.h>
 #include <linux/ioport.h>
 #include <linux/pm.h>

arch/mips/cavium-octeon/smp.c

@@ -194,11 +194,11 @@ static void octeon_init_secondary(void)
 void octeon_prepare_cpus(unsigned int max_cpus)
 {
 	cvmx_write_csr(CVMX_CIU_MBOX_CLRX(cvmx_get_core_num()), 0xffffffff);
-	if (request_irq(OCTEON_IRQ_MBOX0, mailbox_interrupt, IRQF_SHARED,
+	if (request_irq(OCTEON_IRQ_MBOX0, mailbox_interrupt, IRQF_DISABLED,
 			"mailbox0", mailbox_interrupt)) {
 		panic("Cannot request_irq(OCTEON_IRQ_MBOX0)\n");
 	}
-	if (request_irq(OCTEON_IRQ_MBOX1, mailbox_interrupt, IRQF_SHARED,
+	if (request_irq(OCTEON_IRQ_MBOX1, mailbox_interrupt, IRQF_DISABLED,
 			"mailbox1", mailbox_interrupt)) {
 		panic("Cannot request_irq(OCTEON_IRQ_MBOX1)\n");
 	}

arch/mips/dec/ecc-berr.c

@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/ecc-berr.c
- *
  *	Bus error event handling code for systems equipped with ECC
  *	handling logic, i.e. DECstation/DECsystem 5000/200 (KN02),
  *	5000/240 (KN03), 5000/260 (KN05) and DECsystem 5900 (KN03),

arch/mips/dec/int-handler.S

@@ -1,6 +1,4 @@
 /*
- * arch/mips/dec/int-handler.S
- *
  * Copyright (C) 1995, 1996, 1997 Paul M. Antoine and Harald Koerfgen
  * Copyright (C) 2000, 2001, 2002, 2003, 2005  Maciej W. Rozycki
  *

arch/mips/dec/ioasic-irq.c

@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/ioasic-irq.c
- *
  *	DEC I/O ASIC interrupts.
  *
  *	Copyright (c) 2002, 2003  Maciej W. Rozycki

arch/mips/dec/kn01-berr.c

@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/kn01-berr.c
- *
  *	Bus error event handling code for DECstation/DECsystem 3100
  *	and 2100 (KN01) systems equipped with parity error detection
  *	logic.

arch/mips/dec/kn02-irq.c

@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/kn02-irq.c
- *
  *	DECstation 5000/200 (KN02) Control and Status Register
  *	interrupts.
  *

arch/mips/dec/kn02xa-berr.c

@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/kn02xa-berr.c
- *
  *	Bus error event handling code for 5000-series systems equipped
  *	with parity error detection logic, i.e. DECstation/DECsystem
  *	5000/120, /125, /133 (KN02-BA), 5000/150 (KN04-BA) and Personal

arch/mips/dec/prom/call_o32.S

@@ -1,6 +1,4 @@
 /*
- *	arch/mips/dec/prom/call_o32.S
- *
  *	O32 interface for the 64 (or N32) ABI.
  *
  *	Copyright (C) 2002  Maciej W. Rozycki

arch/mips/dec/prom/console.c

@@ -1,6 +1,4 @@
 /*
- *	arch/mips/dec/prom/console.c
- *
  *	DECstation PROM-based early console support.
  *
  *	Copyright (C) 2004, 2007  Maciej W. Rozycki

arch/mips/dec/time.c

@@ -1,6 +1,4 @@
 /*
- *  linux/arch/mips/dec/time.c
- *
  *  Copyright (C) 1991, 1992, 1995  Linus Torvalds
  *  Copyright (C) 2000, 2003  Maciej W. Rozycki
  *

arch/mips/emma/common/Makefile

@@ -1,7 +1,4 @@
 #
-#  arch/mips/emma2rh/common/Makefile
-#       Makefile for the common code of NEC EMMA2RH based board.
-#
 #  Copyright (C) NEC Electronics Corporation 2005-2006
 #
 #  This program is free software; you can redistribute it and/or modify

arch/mips/emma/common/prom.c

@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/common/prom.c
- *      This file is prom file.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This file is based on the arch/mips/ddb5xxx/common/prom.c

arch/mips/emma/markeins/Makefile

@@ -1,7 +1,4 @@
 #
-#  arch/mips/emma2rh/markeins/Makefile
-#       Makefile for the common code of NEC EMMA2RH based board.
-#
 #  Copyright (C) NEC Electronics Corporation 2005-2006
 #
 #  This program is free software; you can redistribute it and/or modify

arch/mips/emma/markeins/irq.c

@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/markeins/irq.c
- *      This file defines the irq handler for EMMA2RH.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This file is based on the arch/mips/ddb5xxx/ddb5477/irq.c

arch/mips/emma/markeins/led.c

@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/markeins/led.c
- *      This file defines the led display for Mark-eins.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This program is free software; you can redistribute it and/or modify

arch/mips/emma/markeins/platform.c

@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/markeins/platofrm.c
- *      This file sets up platform devices for EMMA2RH Mark-eins.
- *
  *  Copyright(C) MontaVista Software Inc, 2006
  *
  *  Author: dmitry pervushin <dpervushin@ru.mvista.com>

arch/mips/emma/markeins/setup.c

@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/markeins/setup.c
- *      This file is setup for EMMA2RH Mark-eins.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This file is based on the arch/mips/ddb5xxx/ddb5477/setup.c.

arch/mips/fw/lib/call_o32.S

@@ -1,6 +1,4 @@
 /*
- *	arch/mips/dec/prom/call_o32.S
- *
  *	O32 interface for the 64 (or N32) ABI.
  *
  *	Copyright (C) 2002  Maciej W. Rozycki

arch/mips/include/asm/emma/emma2rh.h

@@ -1,7 +1,4 @@
 /*
- *  arch/mips/include/asm/emma/emma2rh.h
- *      This file is EMMA2RH common header.
- *
  *  Copyright (C) NEC Electronics Corporation 2005-2006
  *
  *  This file based on include/asm-mips/ddb5xxx/ddb5xxx.h

arch/mips/include/asm/emma/markeins.h

@@ -1,7 +1,4 @@
 /*
- *  include/asm-mips/emma2rh/markeins.h
- *      This file is EMMA2RH board depended header.
- *
  *  Copyright (C) NEC Electronics Corporation 2005-2006
  *
  *  This file based on include/asm-mips/ddb5xxx/ddb5xxx.h

arch/mips/include/asm/gic.h

@@ -20,7 +20,7 @@
 #define GIC_TRIG_EDGE			1
 #define GIC_TRIG_LEVEL			0
 
-#if CONFIG_SMP
+#ifdef CONFIG_SMP
 #define GIC_NUM_INTRS			(24 + NR_CPUS * 2)
 #else
 #define GIC_NUM_INTRS			32

arch/mips/include/asm/pmc-sierra/msp71xx/war.h

@@ -23,6 +23,8 @@
 #if defined(CONFIG_PMC_MSP7120_EVAL) || defined(CONFIG_PMC_MSP7120_GW) || \
 	defined(CONFIG_PMC_MSP7120_FPGA)
 #define MIPS34K_MISSED_ITLB_WAR         1
+#else
+#define MIPS34K_MISSED_ITLB_WAR         0
 #endif
 
 #endif /* __ASM_MIPS_PMC_SIERRA_WAR_H */

arch/mips/include/asm/processor.h

@@ -311,8 +311,9 @@ extern void start_thread(struct pt_regs * regs, unsigned long pc, unsigned long
 
 unsigned long get_wchan(struct task_struct *p);
 
-#define __KSTK_TOS(tsk) ((unsigned long)task_stack_page(tsk) + THREAD_SIZE - 32)
-#define task_pt_regs(tsk) ((struct pt_regs *)__KSTK_TOS(tsk) - 1)
+#define __KSTK_TOS(tsk) ((unsigned long)task_stack_page(tsk) + \
+			 THREAD_SIZE - 32 - sizeof(struct pt_regs))
+#define task_pt_regs(tsk) ((struct pt_regs *)__KSTK_TOS(tsk))
 #define KSTK_EIP(tsk) (task_pt_regs(tsk)->cp0_epc)
 #define KSTK_ESP(tsk) (task_pt_regs(tsk)->regs[29])
 #define KSTK_STATUS(tsk) (task_pt_regs(tsk)->cp0_status)

arch/mips/include/asm/unistd.h

@@ -354,16 +354,17 @@
 #define __NR_pwritev			(__NR_Linux + 331)
 #define __NR_rt_tgsigqueueinfo		(__NR_Linux + 332)
 #define __NR_perf_counter_open		(__NR_Linux + 333)
+#define __NR_accept4			(__NR_Linux + 334)
 
 /*
  * Offset of the last Linux o32 flavoured syscall
  */
-#define __NR_Linux_syscalls		333
+#define __NR_Linux_syscalls		334
 
 #endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
 
 #define __NR_O32_Linux			4000
-#define __NR_O32_Linux_syscalls		333
+#define __NR_O32_Linux_syscalls		334
 
 #if _MIPS_SIM == _MIPS_SIM_ABI64
 
@@ -664,16 +665,17 @@
 #define __NR_pwritev			(__NR_Linux + 290)
 #define __NR_rt_tgsigqueueinfo		(__NR_Linux + 291)
 #define __NR_perf_counter_open		(__NR_Linux + 292)
+#define __NR_accept4			(__NR_Linux + 293)
 
 /*
  * Offset of the last Linux 64-bit flavoured syscall
  */
-#define __NR_Linux_syscalls		292
+#define __NR_Linux_syscalls		293
 
 #endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */
 
 #define __NR_64_Linux			5000
-#define __NR_64_Linux_syscalls		292
+#define __NR_64_Linux_syscalls		293
 
 #if _MIPS_SIM == _MIPS_SIM_NABI32
 
@@ -978,16 +980,17 @@
 #define __NR_pwritev			(__NR_Linux + 294)
 #define __NR_rt_tgsigqueueinfo		(__NR_Linux + 295)
 #define __NR_perf_counter_open		(__NR_Linux + 296)
+#define __NR_accept4			(__NR_Linux + 297)
 
 /*
  * Offset of the last N32 flavoured syscall
  */
-#define __NR_Linux_syscalls		296
+#define __NR_Linux_syscalls		297
 
 #endif /* _MIPS_SIM == _MIPS_SIM_NABI32 */
 
 #define __NR_N32_Linux			6000
-#define __NR_N32_Linux_syscalls		296
+#define __NR_N32_Linux_syscalls		297
 
 #ifdef __KERNEL__
 

arch/mips/jazz/jazzdma.c

@@ -190,7 +190,7 @@ int vdma_free(unsigned long laddr)
 		return -1;
 	}
 
-	while (pgtbl[i].owner == laddr && i < VDMA_PGTBL_ENTRIES) {
+	while (i < VDMA_PGTBL_ENTRIES && pgtbl[i].owner == laddr) {
 		pgtbl[i].owner = VDMA_PAGE_EMPTY;
 		i++;
 	}

arch/mips/kernel/head.S

@@ -188,7 +188,8 @@ NESTED(kernel_entry, 16, sp)			# kernel entry point
 
 	MTC0		zero, CP0_CONTEXT	# clear context register
 	PTR_LA		$28, init_thread_union
-	PTR_LI		sp, _THREAD_SIZE - 32
+	/* Set the SP after an empty pt_regs.  */
+	PTR_LI		sp, _THREAD_SIZE - 32 - PT_SIZE
 	PTR_ADDU	sp, $28
 	set_saved_sp	sp, t0, t1
 	PTR_SUBU	sp, 4 * SZREG		# init stack pointer

arch/mips/kernel/irq_txx9.c

@@ -1,6 +1,4 @@
 /*
- * linux/arch/mips/kernel/irq_txx9.c
- *
  * Based on linux/arch/mips/jmr3927/rbhma3100/irq.c,
  *          linux/arch/mips/tx4927/common/tx4927_irq.c,
  *          linux/arch/mips/tx4938/common/irq.c

arch/mips/kernel/module.c

@@ -98,7 +98,8 @@ static int apply_r_mips_32_rela(struct module *me, u32 *location, Elf_Addr v)
 static int apply_r_mips_26_rel(struct module *me, u32 *location, Elf_Addr v)
 {
 	if (v % 4) {
-		printk(KERN_ERR "module %s: dangerous relocation\n", me->name);
+		pr_err("module %s: dangerous R_MIPS_26 REL relocation\n",
+		       me->name);
 		return -ENOEXEC;
 	}
 
@@ -118,7 +119,8 @@ static int apply_r_mips_26_rel(struct module *me, u32 *location, Elf_Addr v)
 static int apply_r_mips_26_rela(struct module *me, u32 *location, Elf_Addr v)
 {
 	if (v % 4) {
-		printk(KERN_ERR "module %s: dangerous relocation\n", me->name);
+		pr_err("module %s: dangerous R_MIPS_26 RELArelocation\n",
+		       me->name);
 		return -ENOEXEC;
 	}
 
@@ -222,7 +224,7 @@ static int apply_r_mips_lo16_rel(struct module *me, u32 *location, Elf_Addr v)
 	return 0;
 
 out_danger:
-	printk(KERN_ERR "module %s: dangerous " "relocation\n", me->name);
+	pr_err("module %s: dangerous R_MIPS_LO16 REL relocation\n", me->name);
 
 	return -ENOEXEC;
 }
@@ -301,7 +303,7 @@ int apply_relocate(Elf_Shdr *sechdrs, const char *strtab,
 		/* This is the symbol it is referring to */
 		sym = (Elf_Sym *)sechdrs[symindex].sh_addr
 			+ ELF_MIPS_R_SYM(rel[i]);
-		if (!sym->st_value) {
+		if (IS_ERR_VALUE(sym->st_value)) {
 			/* Ignore unresolved weak symbol */
 			if (ELF_ST_BIND(sym->st_info) == STB_WEAK)
 				continue;
@@ -341,7 +343,7 @@ int apply_relocate_add(Elf_Shdr *sechdrs, const char *strtab,
 		/* This is the symbol it is referring to */
 		sym = (Elf_Sym *)sechdrs[symindex].sh_addr
 			+ ELF_MIPS_R_SYM(rel[i]);
-		if (!sym->st_value) {
+		if (IS_ERR_VALUE(sym->st_value)) {
 			/* Ignore unresolved weak symbol */
 			if (ELF_ST_BIND(sym->st_info) == STB_WEAK)
 				continue;

arch/mips/kernel/proc.c

@@ -1,6 +1,4 @@
 /*
- *  linux/arch/mips/kernel/proc.c
- *
  *  Copyright (C) 1995, 1996, 2001  Ralf Baechle
  *  Copyright (C) 2001, 2004  MIPS Technologies, Inc.
  *  Copyright (C) 2004  Maciej W. Rozycki

arch/mips/kernel/process.c

@@ -115,7 +115,7 @@ int copy_thread(unsigned long clone_flags, unsigned long usp,
 {
 	struct thread_info *ti = task_thread_info(p);
 	struct pt_regs *childregs;
-	long childksp;
+	unsigned long childksp;
 	p->set_child_tid = p->clear_child_tid = NULL;
 
 	childksp = (unsigned long)task_stack_page(p) + THREAD_SIZE - 32;
@@ -132,6 +132,8 @@ int copy_thread(unsigned long clone_flags, unsigned long usp,
 
 	/* set up new TSS. */
 	childregs = (struct pt_regs *) childksp - 1;
+	/*  Put the stack after the struct pt_regs.  */
+	childksp = (unsigned long) childregs;
 	*childregs = *regs;
 	childregs->regs[7] = 0;	/* Clear error flag */
 

arch/mips/kernel/scall32-o32.S

@@ -654,6 +654,7 @@ einval:	li	v0, -ENOSYS
 	sys	sys_pwritev		6
 	sys	sys_rt_tgsigqueueinfo	4
 	sys	sys_perf_counter_open	5
+	sys	sys_accept4		4
 	.endm
 
 	/* We pre-compute the number of _instruction_ bytes needed to

arch/mips/kernel/scall64-64.S

@@ -491,4 +491,5 @@ sys_call_table:
 	PTR	sys_pwritev			/* 5390 */
 	PTR	sys_rt_tgsigqueueinfo
 	PTR	sys_perf_counter_open
+	PTR	sys_accept4
 	.size	sys_call_table,.-sys_call_table

arch/mips/kernel/scall64-n32.S

@@ -417,4 +417,5 @@ EXPORT(sysn32_call_table)
 	PTR	sys_pwritev
 	PTR	compat_sys_rt_tgsigqueueinfo	/* 5295 */
 	PTR	sys_perf_counter_open
+	PTR	sys_accept4
 	.size	sysn32_call_table,.-sysn32_call_table

arch/mips/kernel/scall64-o32.S

@@ -537,4 +537,5 @@ sys_call_table:
 	PTR	compat_sys_pwritev
 	PTR	compat_sys_rt_tgsigqueueinfo
 	PTR	sys_perf_counter_open
+	PTR	sys_accept4
 	.size	sys_call_table,.-sys_call_table

arch/mips/kernel/smtc.c

@@ -465,11 +465,8 @@ void smtc_prepare_cpus(int cpus)
 	smtc_configure_tlb();
 
 	for (tc = 0, vpe = 0 ; (vpe < nvpe) && (tc < ntc) ; vpe++) {
-		/*
-		 * Set the MVP bits.
-		 */
-		settc(tc);
-		write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() | VPECONF0_MVP);
+		if (tcpervpe[vpe] == 0)
+			continue;
 		if (vpe != 0)
 			printk(", ");
 		printk("VPE %d: TC", vpe);
@@ -487,6 +484,12 @@ void smtc_prepare_cpus(int cpus)
 			tc++;
 		}
 		if (vpe != 0) {
+			/*
+			 * Allow this VPE to control others.
+			 */
+			write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() |
+					      VPECONF0_MVP);
+
 			/*
 			 * Clear any stale software interrupts from VPE's Cause
 			 */

arch/mips/kernel/stacktrace.c

@@ -1,6 +1,4 @@
 /*
- * arch/mips/kernel/stacktrace.c
- *
  * Stack trace management functions
  *
  *  Copyright (C) 2006 Atsushi Nemoto <anemo@mba.ocn.ne.jp>

arch/mips/kernel/vpe.c

@@ -73,7 +73,7 @@ static int major;
 static const int minor = 1;	/* fixed for now  */
 
 #ifdef CONFIG_MIPS_APSP_KSPD
- static struct kspd_notifications kspd_events;
+static struct kspd_notifications kspd_events;
 static int kspd_events_reqd = 0;
 #endif
 
@@ -155,10 +155,9 @@ struct {
 };
 
 static void release_progmem(void *ptr);
-extern void save_gp_address(unsigned int secbase, unsigned int rel);
 
 /* get the vpe associated with this minor */
-struct vpe *get_vpe(int minor)
+static struct vpe *get_vpe(int minor)
 {
 	struct vpe *v;
 
@@ -174,7 +173,7 @@ struct vpe *get_vpe(int minor)
 }
 
 /* get the vpe associated with this minor */
-struct tc *get_tc(int index)
+static struct tc *get_tc(int index)
 {
 	struct tc *t;
 
@@ -186,20 +185,8 @@ struct tc *get_tc(int index)
 	return NULL;
 }
 
-struct tc *get_tc_unused(void)
-{
-	struct tc *t;
-
-	list_for_each_entry(t, &vpecontrol.tc_list, list) {
-		if (t->state == TC_STATE_UNUSED)
-			return t;
-	}
-
-	return NULL;
-}
-
 /* allocate a vpe and associate it with this minor (or index) */
-struct vpe *alloc_vpe(int minor)
+static struct vpe *alloc_vpe(int minor)
 {
 	struct vpe *v;
 
@@ -216,7 +203,7 @@ struct vpe *alloc_vpe(int minor)
 }
 
 /* allocate a tc. At startup only tc0 is running, all other can be halted. */
-struct tc *alloc_tc(int index)
+static struct tc *alloc_tc(int index)
 {
 	struct tc *tc;
 
@@ -232,7 +219,7 @@ out:
 }
 
 /* clean up and free everything */
-void release_vpe(struct vpe *v)
+static void release_vpe(struct vpe *v)
 {
 	list_del(&v->list);
 	if (v->load_addr)
@@ -240,7 +227,7 @@ void release_vpe(struct vpe *v)
 	kfree(v);
 }
 
-void dump_mtregs(void)
+static void dump_mtregs(void)
 {
 	unsigned long val;
 
@@ -327,7 +314,8 @@ static void layout_sections(struct module *mod, const Elf_Ehdr * hdr,
 			    || (s->sh_flags & masks[m][1])
 			    || s->sh_entsize != ~0UL)
 				continue;
-			s->sh_entsize = get_offset(&mod->core_size, s);
+			s->sh_entsize =
+				get_offset((unsigned long *)&mod->core_size, s);
 		}
 
 		if (m == 0)
@@ -461,16 +449,15 @@ static int apply_r_mips_lo16(struct module *me, uint32_t *location,
 {
 	unsigned long insnlo = *location;
 	Elf32_Addr val, vallo;
+	struct mips_hi16 *l, *next;
 
 	/* Sign extend the addend we extract from the lo insn.  */
 	vallo = ((insnlo & 0xffff) ^ 0x8000) - 0x8000;
 
 	if (mips_hi16_list != NULL) {
-		struct mips_hi16 *l;
 
 		l = mips_hi16_list;
 		while (l != NULL) {
-			struct mips_hi16 *next;
 			unsigned long insn;
 
 			/*
@@ -480,7 +467,7 @@ static int apply_r_mips_lo16(struct module *me, uint32_t *location,
 				printk(KERN_DEBUG "VPE loader: "
 				       "apply_r_mips_lo16/hi16: \t"
 				       "inconsistent value information\n");
-				return -ENOEXEC;
+				goto out_free;
 			}
 
 			/*
@@ -518,6 +505,16 @@ static int apply_r_mips_lo16(struct module *me, uint32_t *location,
 	*location = insnlo;
 
 	return 0;
+
+out_free:
+	while (l != NULL) {
+		next = l->next;
+		kfree(l);
+		l = next;
+	}
+	mips_hi16_list = NULL;
+
+	return -ENOEXEC;
 }
 
 static int (*reloc_handlers[]) (struct module *me, uint32_t *location,
@@ -541,7 +538,7 @@ static char *rstrs[] = {
 	[R_MIPS_PC16] = "MIPS_PC16"
 };
 
-int apply_relocations(Elf32_Shdr *sechdrs,
+static int apply_relocations(Elf32_Shdr *sechdrs,
 		      const char *strtab,
 		      unsigned int symindex,
 		      unsigned int relsec,
@@ -586,7 +583,7 @@ int apply_relocations(Elf32_Shdr *sechdrs,
 	return 0;
 }
 
-void save_gp_address(unsigned int secbase, unsigned int rel)
+static inline void save_gp_address(unsigned int secbase, unsigned int rel)
 {
 	gp_addr = secbase + rel;
 	gp_offs = gp_addr - (secbase & 0xffff0000);

arch/mips/mipssim/sim_time.c

@@ -89,13 +89,13 @@ unsigned __cpuinit get_c0_compare_int(void)
 	if (cpu_has_veic) {
 		set_vi_handler(MSC01E_INT_CPUCTR, mips_timer_dispatch);
 		mips_cpu_timer_irq = MSC01E_INT_BASE + MSC01E_INT_CPUCTR;
-	} else {
-#endif
-	       {
-		if (cpu_has_vint)
-			set_vi_handler(cp0_compare_irq, mips_timer_dispatch);
-		mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq;
+
+		return mips_cpu_timer_irq;
 	}
+#endif
+	if (cpu_has_vint)
+		set_vi_handler(cp0_compare_irq, mips_timer_dispatch);
+	mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq;
 
 	return mips_cpu_timer_irq;
 }