Merge git://git.kernel.org/pub/scm/linux/kernel/git/nico/orion into devel-stable

arch/arm/configs/kirkwood_defconfig

@@ -15,6 +15,7 @@ CONFIG_MACH_MV88F6281GTW_GE=y
 CONFIG_MACH_SHEEVAPLUG=y
 CONFIG_MACH_ESATA_SHEEVAPLUG=y
 CONFIG_MACH_GURUPLUG=y
+CONFIG_MACH_DOCKSTAR=y
 CONFIG_MACH_TS219=y
 CONFIG_MACH_TS41X=y
 CONFIG_MACH_OPENRD_BASE=y

arch/arm/mach-kirkwood/Kconfig

@@ -58,6 +58,12 @@ config MACH_TS41X
 	  QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS
 	  devices.
 
+config MACH_DOCKSTAR
+	bool "Seagate FreeAgent DockStar"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Seagate FreeAgent DockStar.
+
 config MACH_OPENRD
         bool
 
@@ -100,6 +106,12 @@ config MACH_NETSPACE_MAX_V2
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie Network Space Max v2 NAS.
 
+config MACH_D2NET_V2
+	bool "LaCie d2 Network v2 NAS Board"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  LaCie d2 Network v2 NAS.
+
 config MACH_NET2BIG_V2
 	bool "LaCie 2Big Network v2 NAS Board"
 	help

arch/arm/mach-kirkwood/Makefile

@@ -7,14 +7,16 @@ obj-$(CONFIG_MACH_MV88F6281GTW_GE)	+= mv88f6281gtw_ge-setup.o
 obj-$(CONFIG_MACH_SHEEVAPLUG)		+= sheevaplug-setup.o
 obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG)	+= sheevaplug-setup.o
 obj-$(CONFIG_MACH_GURUPLUG)		+= guruplug-setup.o
+obj-$(CONFIG_MACH_DOCKSTAR)		+= dockstar-setup.o
 obj-$(CONFIG_MACH_TS219)		+= ts219-setup.o tsx1x-common.o
 obj-$(CONFIG_MACH_TS41X)		+= ts41x-setup.o tsx1x-common.o
 obj-$(CONFIG_MACH_OPENRD)		+= openrd-setup.o
-obj-$(CONFIG_MACH_NETSPACE_V2)		+= netspace_v2-setup.o
-obj-$(CONFIG_MACH_INETSPACE_V2)		+= netspace_v2-setup.o
-obj-$(CONFIG_MACH_NETSPACE_MAX_V2)	+= netspace_v2-setup.o
-obj-$(CONFIG_MACH_NET2BIG_V2)		+= netxbig_v2-setup.o
-obj-$(CONFIG_MACH_NET5BIG_V2)		+= netxbig_v2-setup.o
+obj-$(CONFIG_MACH_NETSPACE_V2)		+= netspace_v2-setup.o lacie_v2-common.o
+obj-$(CONFIG_MACH_INETSPACE_V2)		+= netspace_v2-setup.o lacie_v2-common.o
+obj-$(CONFIG_MACH_NETSPACE_MAX_V2)	+= netspace_v2-setup.o lacie_v2-common.o
+obj-$(CONFIG_MACH_D2NET_V2)		+= d2net_v2-setup.o lacie_v2-common.o
+obj-$(CONFIG_MACH_NET2BIG_V2)		+= netxbig_v2-setup.o lacie_v2-common.o
+obj-$(CONFIG_MACH_NET5BIG_V2)		+= netxbig_v2-setup.o lacie_v2-common.o
 obj-$(CONFIG_MACH_T5325)		+= t5325-setup.o
 
 obj-$(CONFIG_CPU_IDLE)			+= cpuidle.o

arch/arm/mach-kirkwood/d2net_v2-setup.c

@@ -0,0 +1,231 @@
+/*
+ * arch/arm/mach-kirkwood/d2net_v2-setup.c
+ *
+ * LaCie d2 Network Space v2 Board Setup
+ *
+ * Copyright (C) 2010 Simon Guinot <sguinot@lacie.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/input.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include <mach/leds-ns2.h>
+#include "common.h"
+#include "mpp.h"
+#include "lacie_v2-common.h"
+
+/*****************************************************************************
+ * Ethernet
+ ****************************************************************************/
+
+static struct mv643xx_eth_platform_data d2net_v2_ge00_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
+};
+
+/*****************************************************************************
+ * SATA
+ ****************************************************************************/
+
+static struct mv_sata_platform_data d2net_v2_sata_data = {
+	.n_ports	= 2,
+};
+
+/*****************************************************************************
+ * GPIO keys
+ ****************************************************************************/
+
+#define D2NET_V2_GPIO_PUSH_BUTTON          34
+#define D2NET_V2_GPIO_POWER_SWITCH_ON      13
+#define D2NET_V2_GPIO_POWER_SWITCH_OFF     15
+
+#define D2NET_V2_SWITCH_POWER_ON           0x1
+#define D2NET_V2_SWITCH_POWER_OFF          0x2
+
+static struct gpio_keys_button d2net_v2_buttons[] = {
+	[0] = {
+		.type           = EV_SW,
+		.code           = D2NET_V2_SWITCH_POWER_ON,
+		.gpio           = D2NET_V2_GPIO_POWER_SWITCH_ON,
+		.desc           = "Back power switch (on|auto)",
+		.active_low     = 0,
+	},
+	[1] = {
+		.type           = EV_SW,
+		.code           = D2NET_V2_SWITCH_POWER_OFF,
+		.gpio           = D2NET_V2_GPIO_POWER_SWITCH_OFF,
+		.desc           = "Back power switch (auto|off)",
+		.active_low     = 0,
+	},
+	[2] = {
+		.code           = KEY_POWER,
+		.gpio           = D2NET_V2_GPIO_PUSH_BUTTON,
+		.desc           = "Front Push Button",
+		.active_low     = 1,
+	},
+};
+
+static struct gpio_keys_platform_data d2net_v2_button_data = {
+	.buttons	= d2net_v2_buttons,
+	.nbuttons	= ARRAY_SIZE(d2net_v2_buttons),
+};
+
+static struct platform_device d2net_v2_gpio_buttons = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &d2net_v2_button_data,
+	},
+};
+
+/*****************************************************************************
+ * GPIO LEDs
+ ****************************************************************************/
+
+#define D2NET_V2_GPIO_RED_LED		12
+
+static struct gpio_led d2net_v2_gpio_led_pins[] = {
+	{
+		.name	= "d2net_v2:red:fail",
+		.gpio	= D2NET_V2_GPIO_RED_LED,
+	},
+};
+
+static struct gpio_led_platform_data d2net_v2_gpio_leds_data = {
+	.num_leds	= ARRAY_SIZE(d2net_v2_gpio_led_pins),
+	.leds		= d2net_v2_gpio_led_pins,
+};
+
+static struct platform_device d2net_v2_gpio_leds = {
+	.name		= "leds-gpio",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &d2net_v2_gpio_leds_data,
+	},
+};
+
+/*****************************************************************************
+ * Dual-GPIO CPLD LEDs
+ ****************************************************************************/
+
+#define D2NET_V2_GPIO_BLUE_LED_SLOW	29
+#define D2NET_V2_GPIO_BLUE_LED_CMD	30
+
+static struct ns2_led d2net_v2_led_pins[] = {
+	{
+		.name	= "d2net_v2:blue:sata",
+		.cmd	= D2NET_V2_GPIO_BLUE_LED_CMD,
+		.slow	= D2NET_V2_GPIO_BLUE_LED_SLOW,
+	},
+};
+
+static struct ns2_led_platform_data d2net_v2_leds_data = {
+	.num_leds	= ARRAY_SIZE(d2net_v2_led_pins),
+	.leds		= d2net_v2_led_pins,
+};
+
+static struct platform_device d2net_v2_leds = {
+	.name		= "leds-ns2",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &d2net_v2_leds_data,
+	},
+};
+
+/*****************************************************************************
+ * General Setup
+ ****************************************************************************/
+
+static unsigned int d2net_v2_mpp_config[] __initdata = {
+	MPP0_SPI_SCn,
+	MPP1_SPI_MOSI,
+	MPP2_SPI_SCK,
+	MPP3_SPI_MISO,
+	MPP6_SYSRST_OUTn,
+	MPP7_GPO,		/* Request power-off */
+	MPP8_TW0_SDA,
+	MPP9_TW0_SCK,
+	MPP10_UART0_TXD,
+	MPP11_UART0_RXD,
+	MPP12_GPO,		/* Red led */
+	MPP13_GPIO,		/* Rear power switch (on|auto) */
+	MPP14_GPIO,		/* USB fuse */
+	MPP15_GPIO,		/* Rear power switch (auto|off) */
+	MPP16_GPIO,		/* SATA 0 power */
+	MPP21_SATA0_ACTn,
+	MPP24_GPIO,		/* USB mode select */
+	MPP26_GPIO,		/* USB device vbus */
+	MPP28_GPIO,		/* USB enable host vbus */
+	MPP29_GPIO,		/* Blue led (slow register) */
+	MPP30_GPIO,		/* Blue led (command register) */
+	MPP34_GPIO,		/* Power button (1 = Released, 0 = Pushed) */
+	MPP35_GPIO,		/* Inhibit power-off */
+	0
+};
+
+#define D2NET_V2_GPIO_POWER_OFF		7
+
+static void d2net_v2_power_off(void)
+{
+	gpio_set_value(D2NET_V2_GPIO_POWER_OFF, 1);
+}
+
+static void __init d2net_v2_init(void)
+{
+	/*
+	 * Basic setup. Needs to be called early.
+	 */
+	kirkwood_init();
+	kirkwood_mpp_conf(d2net_v2_mpp_config);
+
+	lacie_v2_hdd_power_init(1);
+
+	kirkwood_ehci_init();
+	kirkwood_ge00_init(&d2net_v2_ge00_data);
+	kirkwood_sata_init(&d2net_v2_sata_data);
+	kirkwood_uart0_init();
+	lacie_v2_register_flash();
+	lacie_v2_register_i2c_devices();
+
+	platform_device_register(&d2net_v2_leds);
+	platform_device_register(&d2net_v2_gpio_leds);
+	platform_device_register(&d2net_v2_gpio_buttons);
+
+	if (gpio_request(D2NET_V2_GPIO_POWER_OFF, "power-off") == 0 &&
+	    gpio_direction_output(D2NET_V2_GPIO_POWER_OFF, 0) == 0)
+		pm_power_off = d2net_v2_power_off;
+	else
+		pr_err("d2net_v2: failed to configure power-off GPIO\n");
+}
+
+MACHINE_START(D2NET_V2, "LaCie d2 Network v2")
+	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
+	.io_pg_offst	= ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= 0x00000100,
+	.init_machine	= d2net_v2_init,
+	.map_io		= kirkwood_map_io,
+	.init_irq	= kirkwood_init_irq,
+	.timer		= &lacie_v2_timer,
+MACHINE_END

arch/arm/mach-kirkwood/dockstar-setup.c

@@ -0,0 +1,112 @@
+/*
+ * arch/arm/mach-kirkwood/dockstar-setup.c
+ *
+ * Seagate FreeAgent DockStar Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include <plat/mvsdio.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mtd_partition dockstar_nand_parts[] = {
+	{
+		.name = "u-boot",
+		.offset = 0,
+		.size = SZ_1M
+	}, {
+		.name = "uImage",
+		.offset = MTDPART_OFS_NXTBLK,
+		.size = SZ_4M
+	}, {
+		.name = "root",
+		.offset = MTDPART_OFS_NXTBLK,
+		.size = MTDPART_SIZ_FULL
+	},
+};
+
+static struct mv643xx_eth_platform_data dockstar_ge00_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct gpio_led dockstar_led_pins[] = {
+	{
+		.name			= "dockstar:green:health",
+		.default_trigger	= "default-on",
+		.gpio			= 46,
+		.active_low		= 1,
+	},
+	{
+		.name			= "dockstar:orange:misc",
+		.default_trigger	= "none",
+		.gpio			= 47,
+		.active_low		= 1,
+	},
+};
+
+static struct gpio_led_platform_data dockstar_led_data = {
+	.leds		= dockstar_led_pins,
+	.num_leds	= ARRAY_SIZE(dockstar_led_pins),
+};
+
+static struct platform_device dockstar_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &dockstar_led_data,
+	}
+};
+
+static unsigned int dockstar_mpp_config[] __initdata = {
+	MPP29_GPIO,	/* USB Power Enable */
+	MPP46_GPIO,	/* LED green */
+	MPP47_GPIO,	/* LED orange */
+	0
+};
+
+static void __init dockstar_init(void)
+{
+	/*
+	 * Basic setup. Needs to be called early.
+	 */
+	kirkwood_init();
+
+	/* setup gpio pin select */
+	kirkwood_mpp_conf(dockstar_mpp_config);
+
+	kirkwood_uart0_init();
+	kirkwood_nand_init(ARRAY_AND_SIZE(dockstar_nand_parts), 25);
+
+	if (gpio_request(29, "USB Power Enable") != 0 ||
+	    gpio_direction_output(29, 1) != 0)
+		printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n");
+	kirkwood_ehci_init();
+
+	kirkwood_ge00_init(&dockstar_ge00_data);
+
+	platform_device_register(&dockstar_leds);
+}
+
+MACHINE_START(DOCKSTAR, "Seagate FreeAgent DockStar")
+	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
+	.io_pg_offst	= ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= 0x00000100,
+	.init_machine	= dockstar_init,
+	.map_io		= kirkwood_map_io,
+	.init_irq	= kirkwood_init_irq,
+	.timer		= &kirkwood_timer,
+MACHINE_END

arch/arm/mach-kirkwood/include/mach/leds-netxbig.h

@@ -0,0 +1,55 @@
+/*
+ * arch/arm/mach-kirkwood/include/mach/leds-netxbig.h
+ *
+ * Platform data structure for netxbig LED driver
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_LEDS_NETXBIG_H
+#define __MACH_LEDS_NETXBIG_H
+
+struct netxbig_gpio_ext {
+	unsigned	*addr;
+	int		num_addr;
+	unsigned	*data;
+	int		num_data;
+	unsigned	enable;
+};
+
+enum netxbig_led_mode {
+	NETXBIG_LED_OFF,
+	NETXBIG_LED_ON,
+	NETXBIG_LED_SATA,
+	NETXBIG_LED_TIMER1,
+	NETXBIG_LED_TIMER2,
+	NETXBIG_LED_MODE_NUM,
+};
+
+#define NETXBIG_LED_INVALID_MODE NETXBIG_LED_MODE_NUM
+
+struct netxbig_led_timer {
+	unsigned long		delay_on;
+	unsigned long		delay_off;
+	enum netxbig_led_mode	mode;
+};
+
+struct netxbig_led {
+	const char	*name;
+	const char	*default_trigger;
+	int		mode_addr;
+	int		*mode_val;
+	int		bright_addr;
+};
+
+struct netxbig_led_platform_data {
+	struct netxbig_gpio_ext	*gpio_ext;
+	struct netxbig_led_timer *timer;
+	int			num_timer;
+	struct netxbig_led	*leds;
+	int			num_leds;
+};
+
+#endif /* __MACH_LEDS_NETXBIG_H */

arch/arm/mach-kirkwood/lacie_v2-common.c

@@ -0,0 +1,127 @@
+/*
+ * arch/arm/mach-kirkwood/lacie_v2-common.c
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/flash.h>
+#include <linux/spi/spi.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+#include <linux/gpio.h>
+#include <asm/mach/time.h>
+#include <mach/kirkwood.h>
+#include <mach/irqs.h>
+#include <plat/time.h>
+#include "common.h"
+
+/*****************************************************************************
+ * 512KB SPI Flash on Boot Device (MACRONIX MX25L4005)
+ ****************************************************************************/
+
+static struct mtd_partition lacie_v2_flash_parts[] = {
+	{
+		.name = "u-boot",
+		.size = MTDPART_SIZ_FULL,
+		.offset = 0,
+		.mask_flags = MTD_WRITEABLE, /* force read-only */
+	},
+};
+
+static const struct flash_platform_data lacie_v2_flash = {
+	.type		= "mx25l4005a",
+	.name		= "spi_flash",
+	.parts		= lacie_v2_flash_parts,
+	.nr_parts	= ARRAY_SIZE(lacie_v2_flash_parts),
+};
+
+static struct spi_board_info __initdata lacie_v2_spi_slave_info[] = {
+	{
+		.modalias	= "m25p80",
+		.platform_data	= &lacie_v2_flash,
+		.irq		= -1,
+		.max_speed_hz	= 20000000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+	},
+};
+
+void __init lacie_v2_register_flash(void)
+{
+	spi_register_board_info(lacie_v2_spi_slave_info,
+				ARRAY_SIZE(lacie_v2_spi_slave_info));
+	kirkwood_spi_init();
+}
+
+/*****************************************************************************
+ * I2C devices
+ ****************************************************************************/
+
+static struct at24_platform_data at24c04 = {
+	.byte_len	= SZ_4K / 8,
+	.page_size	= 16,
+};
+
+/*
+ * i2c addr | chip         | description
+ * 0x50     | HT24LC04     | eeprom (512B)
+ */
+
+static struct i2c_board_info __initdata lacie_v2_i2c_info[] = {
+	{
+		I2C_BOARD_INFO("24c04", 0x50),
+		.platform_data  = &at24c04,
+	}
+};
+
+void __init lacie_v2_register_i2c_devices(void)
+{
+	kirkwood_i2c_init();
+	i2c_register_board_info(0, lacie_v2_i2c_info,
+				ARRAY_SIZE(lacie_v2_i2c_info));
+}
+
+/*****************************************************************************
+ * Hard Disk power
+ ****************************************************************************/
+
+static int __initdata lacie_v2_gpio_hdd_power[] = { 16, 17, 41, 42, 43 };
+
+void __init lacie_v2_hdd_power_init(int hdd_num)
+{
+	int i;
+	int err;
+
+	/* Power up all hard disks. */
+	for (i = 0; i < hdd_num; i++) {
+		err = gpio_request(lacie_v2_gpio_hdd_power[i], NULL);
+		if (err == 0) {
+			err = gpio_direction_output(
+					lacie_v2_gpio_hdd_power[i], 1);
+			/* Free the HDD power GPIOs. This allow user-space to
+			 * configure them via the gpiolib sysfs interface. */
+			gpio_free(lacie_v2_gpio_hdd_power[i]);
+		}
+		if (err)
+			pr_err("Failed to power up HDD%d\n", i + 1);
+	}
+}
+
+/*****************************************************************************
+ * Timer
+ ****************************************************************************/
+
+static void lacie_v2_timer_init(void)
+{
+	kirkwood_tclk = 166666667;
+	orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk);
+}
+
+struct sys_timer lacie_v2_timer = {
+	.init = lacie_v2_timer_init,
+};

arch/arm/mach-kirkwood/lacie_v2-common.h

@@ -0,0 +1,18 @@
+/*
+ * arch/arm/mach-kirkwood/lacie_v2-common.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ARCH_KIRKWOOD_LACIE_V2_COMMON_H
+#define __ARCH_KIRKWOOD_LACIE_V2_COMMON_H
+
+void lacie_v2_register_flash(void);
+void lacie_v2_register_i2c_devices(void);
+void lacie_v2_hdd_power_init(int hdd_num);
+
+extern struct sys_timer lacie_v2_timer;
+
+#endif

arch/arm/mach-kirkwood/netspace_v2-setup.c

@@ -24,56 +24,19 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
 #include <linux/ata_platform.h>
 #include <linux/mv643xx_eth.h>
-#include <linux/i2c.h>
-#include <linux/i2c/at24.h>
 #include <linux/input.h>
 #include <linux/gpio.h>
 #include <linux/gpio_keys.h>
 #include <linux/leds.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
-#include <asm/mach/time.h>
 #include <mach/kirkwood.h>
 #include <mach/leds-ns2.h>
-#include <plat/time.h>
 #include "common.h"
 #include "mpp.h"
-
-/*****************************************************************************
- * 512KB SPI Flash on Boot Device (MACRONIX MX25L4005)
- ****************************************************************************/
-
-static struct mtd_partition netspace_v2_flash_parts[] = {
-	{
-		.name = "u-boot",
-		.size = MTDPART_SIZ_FULL,
-		.offset = 0,
-		.mask_flags = MTD_WRITEABLE, /* force read-only */
-	},
-};
-
-static const struct flash_platform_data netspace_v2_flash = {
-	.type		= "mx25l4005a",
-	.name		= "spi_flash",
-	.parts		= netspace_v2_flash_parts,
-	.nr_parts	= ARRAY_SIZE(netspace_v2_flash_parts),
-};
-
-static struct spi_board_info __initdata netspace_v2_spi_slave_info[] = {
-	{
-		.modalias	= "m25p80",
-		.platform_data	= &netspace_v2_flash,
-		.irq		= -1,
-		.max_speed_hz	= 20000000,
-		.bus_num	= 0,
-		.chip_select	= 0,
-	},
-};
+#include "lacie_v2-common.h"
 
 /*****************************************************************************
  * Ethernet
@@ -83,27 +46,6 @@ static struct mv643xx_eth_platform_data netspace_v2_ge00_data = {
 	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
 };
 
-/*****************************************************************************
- * I2C devices
- ****************************************************************************/
-
-static struct at24_platform_data at24c04 = {
-	.byte_len	= SZ_4K / 8,
-	.page_size	= 16,
-};
-
-/*
- * i2c addr | chip         | description
- * 0x50     | HT24LC04     | eeprom (512B)
- */
-
-static struct i2c_board_info __initdata netspace_v2_i2c_info[] = {
-	{
-		I2C_BOARD_INFO("24c04", 0x50),
-		.platform_data  = &at24c04,
-	}
-};
-
 /*****************************************************************************
  * SATA
  ****************************************************************************/
@@ -112,35 +54,6 @@ static struct mv_sata_platform_data netspace_v2_sata_data = {
 	.n_ports	= 2,
 };
 
-#define NETSPACE_V2_GPIO_SATA0_POWER	16
-#define NETSPACE_V2_GPIO_SATA1_POWER	17
-
-static void __init netspace_v2_sata_power_init(void)
-{
-	int err;
-
-	err = gpio_request(NETSPACE_V2_GPIO_SATA0_POWER, "SATA0 power");
-	if (err == 0) {
-		err = gpio_direction_output(NETSPACE_V2_GPIO_SATA0_POWER, 1);
-		if (err)
-			gpio_free(NETSPACE_V2_GPIO_SATA0_POWER);
-	}
-	if (err)
-		pr_err("netspace_v2: failed to setup SATA0 power\n");
-
-	if (machine_is_netspace_max_v2()) {
-		err = gpio_request(NETSPACE_V2_GPIO_SATA1_POWER, "SATA1 power");
-		if (err == 0) {
-			err = gpio_direction_output(
-					NETSPACE_V2_GPIO_SATA1_POWER, 1);
-			if (err)
-				gpio_free(NETSPACE_V2_GPIO_SATA1_POWER);
-		}
-		if (err)
-			pr_err("netspace_v2: failed to setup SATA1 power\n");
-	}
-}
-
 /*****************************************************************************
  * GPIO keys
  ****************************************************************************/
@@ -223,20 +136,6 @@ static struct platform_device netspace_v2_leds = {
 	},
 };
 
-/*****************************************************************************
- * Timer
- ****************************************************************************/
-
-static void netspace_v2_timer_init(void)
-{
-	kirkwood_tclk = 166666667;
-	orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk);
-}
-
-struct sys_timer netspace_v2_timer = {
-	.init = netspace_v2_timer_init,
-};
-
 /*****************************************************************************
  * General Setup
  ****************************************************************************/
@@ -291,18 +190,17 @@ static void __init netspace_v2_init(void)
 	kirkwood_init();
 	kirkwood_mpp_conf(netspace_v2_mpp_config);
 
-	netspace_v2_sata_power_init();
+	if (machine_is_netspace_max_v2())
+		lacie_v2_hdd_power_init(2);
+	else
+		lacie_v2_hdd_power_init(1);
 
 	kirkwood_ehci_init();
 	kirkwood_ge00_init(&netspace_v2_ge00_data);
 	kirkwood_sata_init(&netspace_v2_sata_data);
 	kirkwood_uart0_init();
-	spi_register_board_info(netspace_v2_spi_slave_info,
-				ARRAY_SIZE(netspace_v2_spi_slave_info));
-	kirkwood_spi_init();
-	kirkwood_i2c_init();
-	i2c_register_board_info(0, netspace_v2_i2c_info,
-				ARRAY_SIZE(netspace_v2_i2c_info));
+	lacie_v2_register_flash();
+	lacie_v2_register_i2c_devices();
 
 	platform_device_register(&netspace_v2_leds);
 	platform_device_register(&netspace_v2_gpio_leds);
@@ -323,7 +221,7 @@ MACHINE_START(NETSPACE_V2, "LaCie Network Space v2")
 	.init_machine	= netspace_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_irq	= kirkwood_init_irq,
-	.timer		= &netspace_v2_timer,
+	.timer		= &lacie_v2_timer,
 MACHINE_END
 #endif
 
@@ -335,7 +233,7 @@ MACHINE_START(INETSPACE_V2, "LaCie Internet Space v2")
 	.init_machine	= netspace_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_irq	= kirkwood_init_irq,
-	.timer		= &netspace_v2_timer,
+	.timer		= &lacie_v2_timer,
 MACHINE_END
 #endif
 
@@ -347,6 +245,6 @@ MACHINE_START(NETSPACE_MAX_V2, "LaCie Network Space Max v2")
 	.init_machine	= netspace_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_irq	= kirkwood_init_irq,
-	.timer		= &netspace_v2_timer,
+	.timer		= &lacie_v2_timer,
 MACHINE_END
 #endif

arch/arm/mach-kirkwood/netxbig_v2-setup.c

@@ -23,55 +23,19 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
 #include <linux/ata_platform.h>
 #include <linux/mv643xx_eth.h>
-#include <linux/i2c.h>
-#include <linux/i2c/at24.h>
 #include <linux/input.h>
 #include <linux/gpio.h>
 #include <linux/gpio_keys.h>
 #include <linux/leds.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
-#include <asm/mach/time.h>
 #include <mach/kirkwood.h>
-#include <plat/time.h>
+#include <mach/leds-netxbig.h>
 #include "common.h"
 #include "mpp.h"
-
-/*****************************************************************************
- * 512KB SPI Flash on Boot Device (MACRONIX MX25L4005)
- ****************************************************************************/
-
-static struct mtd_partition netxbig_v2_flash_parts[] = {
-	{
-		.name = "u-boot",
-		.size = MTDPART_SIZ_FULL,
-		.offset = 0,
-		.mask_flags = MTD_WRITEABLE, /* force read-only */
-	},
-};
-
-static const struct flash_platform_data netxbig_v2_flash = {
-	.type		= "mx25l4005a",
-	.name		= "spi_flash",
-	.parts		= netxbig_v2_flash_parts,
-	.nr_parts	= ARRAY_SIZE(netxbig_v2_flash_parts),
-};
-
-static struct spi_board_info __initdata netxbig_v2_spi_slave_info[] = {
-	{
-		.modalias	= "m25p80",
-		.platform_data	= &netxbig_v2_flash,
-		.irq		= -1,
-		.max_speed_hz	= 20000000,
-		.bus_num	= 0,
-		.chip_select	= 0,
-	},
-};
+#include "lacie_v2-common.h"
 
 /*****************************************************************************
  * Ethernet
@@ -85,27 +49,6 @@ static struct mv643xx_eth_platform_data netxbig_v2_ge01_data = {
 	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
 };
 
-/*****************************************************************************
- * I2C devices
- ****************************************************************************/
-
-static struct at24_platform_data at24c04 = {
-	.byte_len	= SZ_4K / 8,
-	.page_size	= 16,
-};
-
-/*
- * i2c addr | chip         | description
- * 0x50     | HT24LC04     | eeprom (512B)
- */
-
-static struct i2c_board_info __initdata netxbig_v2_i2c_info[] = {
-	{
-		I2C_BOARD_INFO("24c04", 0x50),
-		.platform_data  = &at24c04,
-	}
-};
-
 /*****************************************************************************
  * SATA
  ****************************************************************************/
@@ -114,34 +57,6 @@ static struct mv_sata_platform_data netxbig_v2_sata_data = {
 	.n_ports	= 2,
 };
 
-static int __initdata netxbig_v2_gpio_hdd_power[] = { 16, 17, 41, 42, 43 };
-
-static void __init netxbig_v2_sata_power_init(void)
-{
-	int i;
-	int err;
-	int hdd_nb;
-
-	if (machine_is_net2big_v2())
-		hdd_nb = 2;
-	else
-		hdd_nb = 5;
-
-	/* Power up all hard disks. */
-	for (i = 0; i < hdd_nb; i++) {
-		err = gpio_request(netxbig_v2_gpio_hdd_power[i], NULL);
-		if (err == 0) {
-			err = gpio_direction_output(
-					netxbig_v2_gpio_hdd_power[i], 1);
-			/* Free the HDD power GPIOs. This allow user-space to
-			 * configure them via the gpiolib sysfs interface. */
-			gpio_free(netxbig_v2_gpio_hdd_power[i]);
-		}
-		if (err)
-			pr_err("netxbig_v2: failed to power up HDD%d\n", i + 1);
-	}
-}
-
 /*****************************************************************************
  * GPIO keys
  ****************************************************************************/
@@ -190,7 +105,7 @@ static struct platform_device netxbig_v2_gpio_buttons = {
 };
 
 /*****************************************************************************
- * GPIO LEDs
+ * GPIO extension LEDs
  ****************************************************************************/
 
 /*
@@ -200,19 +115,32 @@ static struct platform_device netxbig_v2_gpio_buttons = {
  * - address register : bit [0-2] -> GPIO [47-49]
  * - data register    : bit [0-2] -> GPIO [44-46]
  * - enable register  : GPIO 29
- *
+ */
+
+static int netxbig_v2_gpio_ext_addr[] = { 47, 48, 49 };
+static int netxbig_v2_gpio_ext_data[] = { 44, 45, 46 };
+
+static struct netxbig_gpio_ext netxbig_v2_gpio_ext = {
+	.addr		= netxbig_v2_gpio_ext_addr,
+	.num_addr	= ARRAY_SIZE(netxbig_v2_gpio_ext_addr),
+	.data		= netxbig_v2_gpio_ext_data,
+	.num_data	= ARRAY_SIZE(netxbig_v2_gpio_ext_data),
+	.enable		= 29,
+};
+
+/*
  * Address register selection:
  *
  * addr | register
  * ----------------------------
  *   0  | front LED
  *   1  | front LED brightness
- *   2  | HDD LED brightness
- *   3  | HDD1 LED
- *   4  | HDD2 LED
- *   5  | HDD3 LED
- *   6  | HDD4 LED
- *   7  | HDD5 LED
+ *   2  | SATA LED brightness
+ *   3  | SATA0 LED
+ *   4  | SATA1 LED
+ *   5  | SATA2 LED
+ *   6  | SATA3 LED
+ *   7  | SATA4 LED
  *
  * Data register configuration:
  *
@@ -233,30 +161,107 @@ static struct platform_device netxbig_v2_gpio_buttons = {
  *   6  | blink blue on=1 sec and red on=1 sec
  *   7  | blink blue on=0.5 sec and blue off=2.5 sec
  *
- * data | HDD LED mode
+ * data | SATA LED mode
  * -------------------------------------------------
- *   0  | fix blue on
+ *   0  | fix off
  *   1  | SATA activity blink
  *   2  | fix red on
  *   3  | blink blue on=1 sec and blue off=1 sec
  *   4  | blink red on=1 sec and red off=1 sec
  *   5  | blink blue on=2.5 sec and red on=0.5 sec
  *   6  | blink blue on=1 sec and red on=1 sec
- *   7  | blink blue on=0.5 sec and blue off=2.5 sec
+ *   7  | fix blue on
  */
 
-/*****************************************************************************
- * Timer
- ****************************************************************************/
+static int netxbig_v2_red_mled[NETXBIG_LED_MODE_NUM] = {
+	[NETXBIG_LED_OFF]	= 0,
+	[NETXBIG_LED_ON]	= 2,
+	[NETXBIG_LED_SATA]	= NETXBIG_LED_INVALID_MODE,
+	[NETXBIG_LED_TIMER1]	= 4,
+	[NETXBIG_LED_TIMER2]	= NETXBIG_LED_INVALID_MODE,
+};
 
-static void netxbig_v2_timer_init(void)
-{
-	kirkwood_tclk = 166666667;
-	orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk);
-}
+static int netxbig_v2_blue_pwr_mled[NETXBIG_LED_MODE_NUM] = {
+	[NETXBIG_LED_OFF]	= 0,
+	[NETXBIG_LED_ON]	= 1,
+	[NETXBIG_LED_SATA]	= NETXBIG_LED_INVALID_MODE,
+	[NETXBIG_LED_TIMER1]	= 3,
+	[NETXBIG_LED_TIMER2]	= 7,
+};
+
+static int netxbig_v2_blue_sata_mled[NETXBIG_LED_MODE_NUM] = {
+	[NETXBIG_LED_OFF]	= 0,
+	[NETXBIG_LED_ON]	= 7,
+	[NETXBIG_LED_SATA]	= 1,
+	[NETXBIG_LED_TIMER1]	= 3,
+	[NETXBIG_LED_TIMER2]	= NETXBIG_LED_INVALID_MODE,
+};
+
+static struct netxbig_led_timer netxbig_v2_led_timer[] = {
+	[0] = {
+		.delay_on	= 500,
+		.delay_off	= 500,
+		.mode		= NETXBIG_LED_TIMER1,
+	},
+	[1] = {
+		.delay_on	= 500,
+		.delay_off	= 1000,
+		.mode		= NETXBIG_LED_TIMER2,
+	},
+};
+
+#define NETXBIG_LED(_name, maddr, mval, baddr)			\
+	{ .name		= _name,				\
+	  .mode_addr	= maddr,				\
+	  .mode_val	= mval,					\
+	  .bright_addr	= baddr }
+
+static struct netxbig_led net2big_v2_leds_ctrl[] = {
+	NETXBIG_LED("net2big-v2:blue:power", 0, netxbig_v2_blue_pwr_mled,  1),
+	NETXBIG_LED("net2big-v2:red:power",  0, netxbig_v2_red_mled,       1),
+	NETXBIG_LED("net2big-v2:blue:sata0", 3, netxbig_v2_blue_sata_mled, 2),
+	NETXBIG_LED("net2big-v2:red:sata0",  3, netxbig_v2_red_mled,       2),
+	NETXBIG_LED("net2big-v2:blue:sata1", 4, netxbig_v2_blue_sata_mled, 2),
+	NETXBIG_LED("net2big-v2:red:sata1",  4, netxbig_v2_red_mled,       2),
+};
+
+static struct netxbig_led_platform_data net2big_v2_leds_data = {
+	.gpio_ext	= &netxbig_v2_gpio_ext,
+	.timer		= netxbig_v2_led_timer,
+	.num_timer	= ARRAY_SIZE(netxbig_v2_led_timer),
+	.leds		= net2big_v2_leds_ctrl,
+	.num_leds	= ARRAY_SIZE(net2big_v2_leds_ctrl),
+};
+
+static struct netxbig_led net5big_v2_leds_ctrl[] = {
+	NETXBIG_LED("net5big-v2:blue:power", 0, netxbig_v2_blue_pwr_mled,  1),
+	NETXBIG_LED("net5big-v2:red:power",  0, netxbig_v2_red_mled,       1),
+	NETXBIG_LED("net5big-v2:blue:sata0", 3, netxbig_v2_blue_sata_mled, 2),
+	NETXBIG_LED("net5big-v2:red:sata0",  3, netxbig_v2_red_mled,       2),
+	NETXBIG_LED("net5big-v2:blue:sata1", 4, netxbig_v2_blue_sata_mled, 2),
+	NETXBIG_LED("net5big-v2:red:sata1",  4, netxbig_v2_red_mled,       2),
+	NETXBIG_LED("net5big-v2:blue:sata2", 5, netxbig_v2_blue_sata_mled, 2),
+	NETXBIG_LED("net5big-v2:red:sata2",  5, netxbig_v2_red_mled,       2),
+	NETXBIG_LED("net5big-v2:blue:sata3", 6, netxbig_v2_blue_sata_mled, 2),
+	NETXBIG_LED("net5big-v2:red:sata3",  6, netxbig_v2_red_mled,       2),
+	NETXBIG_LED("net5big-v2:blue:sata4", 7, netxbig_v2_blue_sata_mled, 2),
+	NETXBIG_LED("net5big-v2:red:sata5",  7, netxbig_v2_red_mled,       2),
+};
 
-struct sys_timer netxbig_v2_timer = {
-	.init = netxbig_v2_timer_init,
+static struct netxbig_led_platform_data net5big_v2_leds_data = {
+	.gpio_ext	= &netxbig_v2_gpio_ext,
+	.timer		= netxbig_v2_led_timer,
+	.num_timer	= ARRAY_SIZE(netxbig_v2_led_timer),
+	.leds		= net5big_v2_leds_ctrl,
+	.num_leds	= ARRAY_SIZE(net5big_v2_leds_ctrl),
+};
+
+static struct platform_device netxbig_v2_leds = {
+	.name		= "leds-netxbig",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &net2big_v2_leds_data,
+	},
 };
 
 /*****************************************************************************
@@ -284,18 +289,18 @@ static unsigned int net2big_v2_mpp_config[] __initdata = {
 	MPP24_GPIO,		/* USB mode select */
 	MPP26_GPIO,		/* USB device vbus */
 	MPP28_GPIO,		/* USB enable host vbus */
-	MPP29_GPIO,		/* CPLD extension ALE */
+	MPP29_GPIO,		/* GPIO extension ALE */
 	MPP34_GPIO,		/* Rear Push button */
 	MPP35_GPIO,		/* Inhibit switch power-off */
 	MPP36_GPIO,		/* SATA HDD1 presence */
 	MPP37_GPIO,		/* SATA HDD2 presence */
 	MPP40_GPIO,		/* eSATA presence */
-	MPP44_GPIO,		/* CPLD extension (data 0) */
-	MPP45_GPIO,		/* CPLD extension (data 1) */
-	MPP46_GPIO,		/* CPLD extension (data 2) */
-	MPP47_GPIO,		/* CPLD extension (addr 0) */
-	MPP48_GPIO,		/* CPLD extension (addr 1) */
-	MPP49_GPIO,		/* CPLD extension (addr 2) */
+	MPP44_GPIO,		/* GPIO extension (data 0) */
+	MPP45_GPIO,		/* GPIO extension (data 1) */
+	MPP46_GPIO,		/* GPIO extension (data 2) */
+	MPP47_GPIO,		/* GPIO extension (addr 0) */
+	MPP48_GPIO,		/* GPIO extension (addr 1) */
+	MPP49_GPIO,		/* GPIO extension (addr 2) */
 	0
 };
 
@@ -324,7 +329,7 @@ static unsigned int net5big_v2_mpp_config[] __initdata = {
 	MPP26_GE1_RXD2,
 	MPP27_GE1_RXD3,
 	MPP28_GPIO,		/* USB enable host vbus */
-	MPP29_GPIO,		/* CPLD extension ALE */
+	MPP29_GPIO,		/* GPIO extension ALE */
 	MPP30_GE1_RXCTL,
 	MPP31_GE1_RXCLK,
 	MPP32_GE1_TCLKOUT,
@@ -339,12 +344,12 @@ static unsigned int net5big_v2_mpp_config[] __initdata = {
 	MPP41_GPIO,		/* SATA HDD3 power */
 	MPP42_GPIO,		/* SATA HDD4 power */
 	MPP43_GPIO,		/* SATA HDD5 power */
-	MPP44_GPIO,		/* CPLD extension (data 0) */
-	MPP45_GPIO,		/* CPLD extension (data 1) */
-	MPP46_GPIO,		/* CPLD extension (data 2) */
-	MPP47_GPIO,		/* CPLD extension (addr 0) */
-	MPP48_GPIO,		/* CPLD extension (addr 1) */
-	MPP49_GPIO,		/* CPLD extension (addr 2) */
+	MPP44_GPIO,		/* GPIO extension (data 0) */
+	MPP45_GPIO,		/* GPIO extension (data 1) */
+	MPP46_GPIO,		/* GPIO extension (data 2) */
+	MPP47_GPIO,		/* GPIO extension (addr 0) */
+	MPP48_GPIO,		/* GPIO extension (addr 1) */
+	MPP49_GPIO,		/* GPIO extension (addr 2) */
 	0
 };
 
@@ -366,7 +371,10 @@ static void __init netxbig_v2_init(void)
 	else
 		kirkwood_mpp_conf(net5big_v2_mpp_config);
 
-	netxbig_v2_sata_power_init();
+	if (machine_is_net2big_v2())
+		lacie_v2_hdd_power_init(2);
+	else
+		lacie_v2_hdd_power_init(5);
 
 	kirkwood_ehci_init();
 	kirkwood_ge00_init(&netxbig_v2_ge00_data);
@@ -374,13 +382,12 @@ static void __init netxbig_v2_init(void)
 		kirkwood_ge01_init(&netxbig_v2_ge01_data);
 	kirkwood_sata_init(&netxbig_v2_sata_data);
 	kirkwood_uart0_init();
-	spi_register_board_info(netxbig_v2_spi_slave_info,
-				ARRAY_SIZE(netxbig_v2_spi_slave_info));
-	kirkwood_spi_init();
-	kirkwood_i2c_init();
-	i2c_register_board_info(0, netxbig_v2_i2c_info,
-				ARRAY_SIZE(netxbig_v2_i2c_info));
+	lacie_v2_register_flash();
+	lacie_v2_register_i2c_devices();
 
+	if (machine_is_net5big_v2())
+		netxbig_v2_leds.dev.platform_data = &net5big_v2_leds_data;
+	platform_device_register(&netxbig_v2_leds);
 	platform_device_register(&netxbig_v2_gpio_buttons);
 
 	if (gpio_request(NETXBIG_V2_GPIO_POWER_OFF, "power-off") == 0 &&
@@ -398,7 +405,7 @@ MACHINE_START(NET2BIG_V2, "LaCie 2Big Network v2")
 	.init_machine	= netxbig_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_irq	= kirkwood_init_irq,
-	.timer		= &netxbig_v2_timer,
+	.timer		= &lacie_v2_timer,
 MACHINE_END
 #endif
 
@@ -410,6 +417,6 @@ MACHINE_START(NET5BIG_V2, "LaCie 5Big Network v2")
 	.init_machine	= netxbig_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_irq	= kirkwood_init_irq,
-	.timer		= &netxbig_v2_timer,
+	.timer		= &lacie_v2_timer,
 MACHINE_END
 #endif

arch/arm/mach-kirkwood/openrd-setup.c

@@ -16,6 +16,7 @@
 #include <linux/ata_platform.h>
 #include <linux/mv643xx_eth.h>
 #include <linux/i2c.h>
+#include <linux/gpio.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <mach/kirkwood.h>
@@ -57,7 +58,22 @@ static struct mvsdio_platform_data openrd_mvsdio_data = {
 };
 
 static unsigned int openrd_mpp_config[] __initdata = {
+	MPP12_SD_CLK,
+	MPP13_SD_CMD,
+	MPP14_SD_D0,
+	MPP15_SD_D1,
+	MPP16_SD_D2,
+	MPP17_SD_D3,
+	MPP28_GPIO,
 	MPP29_GPIO,
+	MPP34_GPIO,
+	0
+};
+
+/* Configure MPP for UART1 */
+static unsigned int openrd_uart1_mpp_config[] __initdata = {
+	MPP13_UART1_TXD,
+	MPP14_UART1_RXD,
 	0
 };
 
@@ -67,6 +83,68 @@ static struct i2c_board_info i2c_board_info[] __initdata = {
 	},
 };
 
+static int __initdata uart1;
+
+static int __init sd_uart_selection(char *str)
+{
+	uart1 = -EINVAL;
+
+	/* Default is SD. Change if required, for UART */
+	if (!str)
+		return 0;
+
+	if (!strncmp(str, "232", 3)) {
+		uart1 = 232;
+	} else if (!strncmp(str, "485", 3)) {
+		/* OpenRD-Base doesn't have RS485. Treat is as an
+		 * unknown argument & just have default setting -
+		 * which is SD */
+		if (machine_is_openrd_base()) {
+			uart1 = -ENODEV;
+			return 1;
+		}
+
+		uart1 = 485;
+	}
+	return 1;
+}
+/* Parse boot_command_line string kw_openrd_init_uart1=232/485 */
+__setup("kw_openrd_init_uart1=", sd_uart_selection);
+
+static int __init uart1_mpp_config(void)
+{
+	kirkwood_mpp_conf(openrd_uart1_mpp_config);
+
+	if (gpio_request(34, "SD_UART1_SEL")) {
+		printk(KERN_ERR "GPIO request failed for SD/UART1 selection"
+				", gpio: 34\n");
+		return -EIO;
+	}
+
+	if (gpio_request(28, "RS232_RS485_SEL")) {
+		printk(KERN_ERR "GPIO request failed for RS232/RS485 selection"
+				", gpio# 28\n");
+		gpio_free(34);
+		return -EIO;
+	}
+
+	/* Select UART1
+	 * Pin # 34: 0 => UART1, 1 => SD */
+	gpio_direction_output(34, 0);
+
+	/* Select RS232 OR RS485
+	 * Pin # 28: 0 => RS232, 1 => RS485 */
+	if (uart1 == 232)
+		gpio_direction_output(28, 0);
+	else
+		gpio_direction_output(28, 1);
+
+	gpio_free(34);
+	gpio_free(28);
+
+	return 0;
+}
+
 static void __init openrd_init(void)
 {
 	/*
@@ -90,7 +168,6 @@ static void __init openrd_init(void)
 		kirkwood_ge01_init(&openrd_ge01_data);
 
 	kirkwood_sata_init(&openrd_sata_data);
-	kirkwood_sdio_init(&openrd_mvsdio_data);
 
 	kirkwood_i2c_init();
 
@@ -99,6 +176,28 @@ static void __init openrd_init(void)
 			ARRAY_SIZE(i2c_board_info));
 		kirkwood_audio_init();
 	}
+
+	if (uart1 <= 0) {
+		if (uart1 < 0)
+			printk(KERN_ERR "Invalid kernel parameter to select "
+				"UART1. Defaulting to SD. ERROR CODE: %d\n",
+				uart1);
+
+		/* Select SD
+		 * Pin # 34: 0 => UART1, 1 => SD */
+		if (gpio_request(34, "SD_UART1_SEL")) {
+			printk(KERN_ERR "GPIO request failed for SD/UART1 "
+					"selection, gpio: 34\n");
+		} else {
+
+			gpio_direction_output(34, 1);
+			gpio_free(34);
+			kirkwood_sdio_init(&openrd_mvsdio_data);
+		}
+	} else {
+		if (!uart1_mpp_config())
+			kirkwood_uart1_init();
+	}
 }
 
 static int __init openrd_pci_init(void)

drivers/leds/Kconfig

@@ -304,13 +304,22 @@ config LEDS_MC13783
 
 config LEDS_NS2
 	tristate "LED support for Network Space v2 GPIO LEDs"
-	depends on MACH_NETSPACE_V2 || MACH_INETSPACE_V2 || MACH_NETSPACE_MAX_V2
+	depends on MACH_NETSPACE_V2 || MACH_INETSPACE_V2 || MACH_NETSPACE_MAX_V2 || D2NET_V2
 	default y
 	help
 	  This option enable support for the dual-GPIO LED found on the
 	  Network Space v2 board (and parents). This include Internet Space v2,
 	  Network Space (Max) v2 and d2 Network v2 boards.
 
+config LEDS_NETXBIG
+	tristate "LED support for Big Network series LEDs"
+	depends on MACH_NET2BIG_V2 || MACH_NET5BIG_V2
+	default y
+	help
+	  This option enable support for LEDs found on the LaCie 2Big
+	  and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
+	  controlled through a GPIO extension bus.
+
 config LEDS_TRIGGERS
 	bool "LED Trigger support"
 	help

drivers/leds/Makefile

@@ -38,6 +38,7 @@ obj-$(CONFIG_LEDS_ADP5520)		+= leds-adp5520.o
 obj-$(CONFIG_LEDS_DELL_NETBOOKS)	+= dell-led.o
 obj-$(CONFIG_LEDS_MC13783)		+= leds-mc13783.o
 obj-$(CONFIG_LEDS_NS2)			+= leds-ns2.o
+obj-$(CONFIG_LEDS_NETXBIG)		+= leds-netxbig.o
 
 # LED SPI Drivers
 obj-$(CONFIG_LEDS_DAC124S085)		+= leds-dac124s085.o

drivers/leds/leds-netxbig.c

@@ -0,0 +1,449 @@
+/*
+ * leds-netxbig.c - Driver for the 2Big and 5Big Network series LEDs
+ *
+ * Copyright (C) 2010 LaCie
+ *
+ * Author: Simon Guinot <sguinot@lacie.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <mach/leds-netxbig.h>
+
+/*
+ * GPIO extension bus.
+ */
+
+static DEFINE_SPINLOCK(gpio_ext_lock);
+
+static void gpio_ext_set_addr(struct netxbig_gpio_ext *gpio_ext, int addr)
+{
+	int pin;
+
+	for (pin = 0; pin < gpio_ext->num_addr; pin++)
+		gpio_set_value(gpio_ext->addr[pin], (addr >> pin) & 1);
+}
+
+static void gpio_ext_set_data(struct netxbig_gpio_ext *gpio_ext, int data)
+{
+	int pin;
+
+	for (pin = 0; pin < gpio_ext->num_data; pin++)
+		gpio_set_value(gpio_ext->data[pin], (data >> pin) & 1);
+}
+
+static void gpio_ext_enable_select(struct netxbig_gpio_ext *gpio_ext)
+{
+	/* Enable select is done on the raising edge. */
+	gpio_set_value(gpio_ext->enable, 0);
+	gpio_set_value(gpio_ext->enable, 1);
+}
+
+static void gpio_ext_set_value(struct netxbig_gpio_ext *gpio_ext,
+			       int addr, int value)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&gpio_ext_lock, flags);
+	gpio_ext_set_addr(gpio_ext, addr);
+	gpio_ext_set_data(gpio_ext, value);
+	gpio_ext_enable_select(gpio_ext);
+	spin_unlock_irqrestore(&gpio_ext_lock, flags);
+}
+
+static int __devinit gpio_ext_init(struct netxbig_gpio_ext *gpio_ext)
+{
+	int err;
+	int i;
+
+	if (unlikely(!gpio_ext))
+		return -EINVAL;
+
+	/* Configure address GPIOs. */
+	for (i = 0; i < gpio_ext->num_addr; i++) {
+		err = gpio_request(gpio_ext->addr[i], "GPIO extension addr");
+		if (err)
+			goto err_free_addr;
+		err = gpio_direction_output(gpio_ext->addr[i], 0);
+		if (err) {
+			gpio_free(gpio_ext->addr[i]);
+			goto err_free_addr;
+		}
+	}
+	/* Configure data GPIOs. */
+	for (i = 0; i < gpio_ext->num_data; i++) {
+		err = gpio_request(gpio_ext->data[i], "GPIO extension data");
+		if (err)
+			goto err_free_data;
+		err = gpio_direction_output(gpio_ext->data[i], 0);
+		if (err) {
+			gpio_free(gpio_ext->data[i]);
+			goto err_free_data;
+		}
+	}
+	/* Configure "enable select" GPIO. */
+	err = gpio_request(gpio_ext->enable, "GPIO extension enable");
+	if (err)
+		goto err_free_data;
+	err = gpio_direction_output(gpio_ext->enable, 0);
+	if (err) {
+		gpio_free(gpio_ext->enable);
+		goto err_free_data;
+	}
+
+	return 0;
+
+err_free_data:
+	for (i = i - 1; i >= 0; i--)
+		gpio_free(gpio_ext->data[i]);
+	i = gpio_ext->num_addr;
+err_free_addr:
+	for (i = i - 1; i >= 0; i--)
+		gpio_free(gpio_ext->addr[i]);
+
+	return err;
+}
+
+static void __devexit gpio_ext_free(struct netxbig_gpio_ext *gpio_ext)
+{
+	int i;
+
+	gpio_free(gpio_ext->enable);
+	for (i = gpio_ext->num_addr - 1; i >= 0; i--)
+		gpio_free(gpio_ext->addr[i]);
+	for (i = gpio_ext->num_data - 1; i >= 0; i--)
+		gpio_free(gpio_ext->data[i]);
+}
+
+/*
+ * Class LED driver.
+ */
+
+struct netxbig_led_data {
+	struct netxbig_gpio_ext	*gpio_ext;
+	struct led_classdev	cdev;
+	int			mode_addr;
+	int			*mode_val;
+	int			bright_addr;
+	int			bright_max;
+	struct			netxbig_led_timer *timer;
+	int			num_timer;
+	enum netxbig_led_mode	mode;
+	int			sata;
+	spinlock_t		lock;
+};
+
+static int netxbig_led_get_timer_mode(enum netxbig_led_mode *mode,
+				      unsigned long delay_on,
+				      unsigned long delay_off,
+				      struct netxbig_led_timer *timer,
+				      int num_timer)
+{
+	int i;
+
+	for (i = 0; i < num_timer; i++) {
+		if (timer[i].delay_on == delay_on &&
+		    timer[i].delay_off == delay_off) {
+			*mode = timer[i].mode;
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
+static int netxbig_led_blink_set(struct led_classdev *led_cdev,
+				 unsigned long *delay_on,
+				 unsigned long *delay_off)
+{
+	struct netxbig_led_data *led_dat =
+		container_of(led_cdev, struct netxbig_led_data, cdev);
+	enum netxbig_led_mode mode;
+	int mode_val;
+	int ret;
+
+	/* Look for a LED mode with the requested timer frequency. */
+	ret = netxbig_led_get_timer_mode(&mode, *delay_on, *delay_off,
+					 led_dat->timer, led_dat->num_timer);
+	if (ret < 0)
+		return ret;
+
+	mode_val = led_dat->mode_val[mode];
+	if (mode_val == NETXBIG_LED_INVALID_MODE)
+		return -EINVAL;
+
+	spin_lock_irq(&led_dat->lock);
+
+	gpio_ext_set_value(led_dat->gpio_ext, led_dat->mode_addr, mode_val);
+	led_dat->mode = mode;
+
+	spin_unlock_irq(&led_dat->lock);
+
+	return 0;
+}
+
+static void netxbig_led_set(struct led_classdev *led_cdev,
+			    enum led_brightness value)
+{
+	struct netxbig_led_data *led_dat =
+		container_of(led_cdev, struct netxbig_led_data, cdev);
+	enum netxbig_led_mode mode;
+	int mode_val, bright_val;
+	int set_brightness = 1;
+	unsigned long flags;
+
+	spin_lock_irqsave(&led_dat->lock, flags);
+
+	if (value == LED_OFF) {
+		mode = NETXBIG_LED_OFF;
+		set_brightness = 0;
+	} else {
+		if (led_dat->sata)
+			mode = NETXBIG_LED_SATA;
+		else if (led_dat->mode == NETXBIG_LED_OFF)
+			mode = NETXBIG_LED_ON;
+		else /* Keep 'timer' mode. */
+			mode = led_dat->mode;
+	}
+	mode_val = led_dat->mode_val[mode];
+
+	gpio_ext_set_value(led_dat->gpio_ext, led_dat->mode_addr, mode_val);
+	led_dat->mode = mode;
+	/*
+	 * Note that the brightness register is shared between all the
+	 * SATA LEDs. So, change the brightness setting for a single
+	 * SATA LED will affect all the others.
+	 */
+	if (set_brightness) {
+		bright_val = DIV_ROUND_UP(value * led_dat->bright_max,
+					  LED_FULL);
+		gpio_ext_set_value(led_dat->gpio_ext,
+				   led_dat->bright_addr, bright_val);
+	}
+
+	spin_unlock_irqrestore(&led_dat->lock, flags);
+}
+
+static ssize_t netxbig_led_sata_store(struct device *dev,
+				      struct device_attribute *attr,
+				      const char *buff, size_t count)
+{
+	struct led_classdev *led_cdev = dev_get_drvdata(dev);
+	struct netxbig_led_data *led_dat =
+		container_of(led_cdev, struct netxbig_led_data, cdev);
+	unsigned long enable;
+	enum netxbig_led_mode mode;
+	int mode_val;
+	int ret;
+
+	ret = strict_strtoul(buff, 10, &enable);
+	if (ret < 0)
+		return ret;
+
+	enable = !!enable;
+
+	spin_lock_irq(&led_dat->lock);
+
+	if (led_dat->sata == enable) {
+		ret = count;
+		goto exit_unlock;
+	}
+
+	if (led_dat->mode != NETXBIG_LED_ON &&
+	    led_dat->mode != NETXBIG_LED_SATA)
+		mode = led_dat->mode; /* Keep modes 'off' and 'timer'. */
+	else if (enable)
+		mode = NETXBIG_LED_SATA;
+	else
+		mode = NETXBIG_LED_ON;
+
+	mode_val = led_dat->mode_val[mode];
+	if (mode_val == NETXBIG_LED_INVALID_MODE) {
+		ret = -EINVAL;
+		goto exit_unlock;
+	}
+
+	gpio_ext_set_value(led_dat->gpio_ext, led_dat->mode_addr, mode_val);
+	led_dat->mode = mode;
+	led_dat->sata = enable;
+
+	ret = count;
+
+exit_unlock:
+	spin_unlock_irq(&led_dat->lock);
+
+	return ret;
+}
+
+static ssize_t netxbig_led_sata_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	struct led_classdev *led_cdev = dev_get_drvdata(dev);
+	struct netxbig_led_data *led_dat =
+		container_of(led_cdev, struct netxbig_led_data, cdev);
+
+	return sprintf(buf, "%d\n", led_dat->sata);
+}
+
+static DEVICE_ATTR(sata, 0644, netxbig_led_sata_show, netxbig_led_sata_store);
+
+static void __devexit delete_netxbig_led(struct netxbig_led_data *led_dat)
+{
+	if (led_dat->mode_val[NETXBIG_LED_SATA] != NETXBIG_LED_INVALID_MODE)
+		device_remove_file(led_dat->cdev.dev, &dev_attr_sata);
+	led_classdev_unregister(&led_dat->cdev);
+}
+
+static int __devinit
+create_netxbig_led(struct platform_device *pdev,
+		   struct netxbig_led_data *led_dat,
+		   const struct netxbig_led *template)
+{
+	struct netxbig_led_platform_data *pdata = pdev->dev.platform_data;
+	int ret;
+
+	spin_lock_init(&led_dat->lock);
+	led_dat->gpio_ext = pdata->gpio_ext;
+	led_dat->cdev.name = template->name;
+	led_dat->cdev.default_trigger = template->default_trigger;
+	led_dat->cdev.blink_set = netxbig_led_blink_set;
+	led_dat->cdev.brightness_set = netxbig_led_set;
+	/*
+	 * Because the GPIO extension bus don't allow to read registers
+	 * value, there is no way to probe the LED initial state.
+	 * So, the initial sysfs LED value for the "brightness" and "sata"
+	 * attributes are inconsistent.
+	 *
+	 * Note that the initial LED state can't be reconfigured.
+	 * The reason is that the LED behaviour must stay uniform during
+	 * the whole boot process (bootloader+linux).
+	 */
+	led_dat->sata = 0;
+	led_dat->cdev.brightness = LED_OFF;
+	led_dat->cdev.flags |= LED_CORE_SUSPENDRESUME;
+	led_dat->mode_addr = template->mode_addr;
+	led_dat->mode_val = template->mode_val;
+	led_dat->bright_addr = template->bright_addr;
+	led_dat->bright_max = (1 << pdata->gpio_ext->num_data) - 1;
+	led_dat->timer = pdata->timer;
+	led_dat->num_timer = pdata->num_timer;
+
+	ret = led_classdev_register(&pdev->dev, &led_dat->cdev);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * If available, expose the SATA activity blink capability through
+	 * a "sata" sysfs attribute.
+	 */
+	if (led_dat->mode_val[NETXBIG_LED_SATA] != NETXBIG_LED_INVALID_MODE) {
+		ret = device_create_file(led_dat->cdev.dev, &dev_attr_sata);
+		if (ret)
+			led_classdev_unregister(&led_dat->cdev);
+	}
+
+	return ret;
+}
+
+static int __devinit netxbig_led_probe(struct platform_device *pdev)
+{
+	struct netxbig_led_platform_data *pdata = pdev->dev.platform_data;
+	struct netxbig_led_data *leds_data;
+	int i;
+	int ret;
+
+	if (!pdata)
+		return -EINVAL;
+
+	leds_data = kzalloc(sizeof(struct netxbig_led_data) * pdata->num_leds,
+			    GFP_KERNEL);
+	if (!leds_data)
+		return -ENOMEM;
+
+	ret = gpio_ext_init(pdata->gpio_ext);
+	if (ret < 0)
+		goto err_free_data;
+
+	for (i = 0; i < pdata->num_leds; i++) {
+		ret = create_netxbig_led(pdev, &leds_data[i], &pdata->leds[i]);
+		if (ret < 0)
+			goto err_free_leds;
+	}
+
+	platform_set_drvdata(pdev, leds_data);
+
+	return 0;
+
+err_free_leds:
+	for (i = i - 1; i >= 0; i--)
+		delete_netxbig_led(&leds_data[i]);
+
+	gpio_ext_free(pdata->gpio_ext);
+err_free_data:
+	kfree(leds_data);
+
+	return ret;
+}
+
+static int __devexit netxbig_led_remove(struct platform_device *pdev)
+{
+	struct netxbig_led_platform_data *pdata = pdev->dev.platform_data;
+	struct netxbig_led_data *leds_data;
+	int i;
+
+	leds_data = platform_get_drvdata(pdev);
+
+	for (i = 0; i < pdata->num_leds; i++)
+		delete_netxbig_led(&leds_data[i]);
+
+	gpio_ext_free(pdata->gpio_ext);
+	kfree(leds_data);
+
+	return 0;
+}
+
+static struct platform_driver netxbig_led_driver = {
+	.probe		= netxbig_led_probe,
+	.remove		= __devexit_p(netxbig_led_remove),
+	.driver		= {
+		.name	= "leds-netxbig",
+		.owner	= THIS_MODULE,
+	},
+};
+MODULE_ALIAS("platform:leds-netxbig");
+
+static int __init netxbig_led_init(void)
+{
+	return platform_driver_register(&netxbig_led_driver);
+}
+
+static void __exit netxbig_led_exit(void)
+{
+	platform_driver_unregister(&netxbig_led_driver);
+}
+
+module_init(netxbig_led_init);
+module_exit(netxbig_led_exit);
+
+MODULE_AUTHOR("Simon Guinot <sguinot@lacie.com>");
+MODULE_DESCRIPTION("LED driver for LaCie xBig Network boards");
+MODULE_LICENSE("GPL");

drivers/leds/leds-ns2.c

@@ -141,10 +141,12 @@ static ssize_t ns2_led_sata_store(struct device *dev,
 				  struct device_attribute *attr,
 				  const char *buff, size_t count)
 {
+	struct led_classdev *led_cdev = dev_get_drvdata(dev);
+	struct ns2_led_data *led_dat =
+		container_of(led_cdev, struct ns2_led_data, cdev);
 	int ret;
 	unsigned long enable;
 	enum ns2_led_modes mode;
-	struct ns2_led_data *led_dat = dev_get_drvdata(dev);
 
 	ret = strict_strtoul(buff, 10, &enable);
 	if (ret < 0)
@@ -172,7 +174,9 @@ static ssize_t ns2_led_sata_store(struct device *dev,
 static ssize_t ns2_led_sata_show(struct device *dev,
 				 struct device_attribute *attr, char *buf)
 {
-	struct ns2_led_data *led_dat = dev_get_drvdata(dev);
+	struct led_classdev *led_cdev = dev_get_drvdata(dev);
+	struct ns2_led_data *led_dat =
+		container_of(led_cdev, struct ns2_led_data, cdev);
 
 	return sprintf(buf, "%d\n", led_dat->sata);
 }
@@ -234,7 +238,6 @@ create_ns2_led(struct platform_device *pdev, struct ns2_led_data *led_dat,
 	if (ret < 0)
 		goto err_free_slow;
 
-	dev_set_drvdata(led_dat->cdev.dev, led_dat);
 	ret = device_create_file(led_dat->cdev.dev, &dev_attr_sata);
 	if (ret < 0)
 		goto err_free_cdev;