pinctrl: Drop TZ1090 drivers

Now that arch/metag/ has been removed, along with TZ1090 SoC support,
remove the TZ1090 pinctrl drivers. They are of no value without the
architecture and SoC platform code.

Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt

@@ -1,127 +0,0 @@
-ImgTec TZ1090 PDC pin controller
-
-Required properties:
-- compatible: "img,tz1090-pdc-pinctrl"
-- reg: Should contain the register physical address and length of the
-  SOC_GPIO_CONTROL registers in the PDC register region.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-TZ1090-PDC's pin configuration nodes act as a container for an arbitrary number
-of subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function. For this reason, even seemingly boolean
-values are actually tristates in this binding: unspecified, off, or on.
-Unspecified is represented as an absent property, and off/on are represented as
-integer values 0 and 1.
-
-Required subnode-properties:
-- tz1090,pins : An array of strings. Each string contains the name of a pin or
-  group. Valid values for these names are listed below.
-
-Optional subnode-properties:
-- tz1090,function: A string containing the name of the function to mux to the
-  pin or group. Valid values for function names are listed below, including
-  which pingroups can be muxed to them.
-- supported generic pinconfig properties (for further details see
-  Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt):
-  - bias-disable
-  - bias-high-impedance
-  - bias-bus-hold
-  - bias-pull-up
-  - bias-pull-down
-  - input-schmitt-enable
-  - input-schmitt-disable
-  - drive-strength: Integer, control drive strength of pins in mA.
-      2: 2mA
-      4: 4mA
-      8: 8mA
-      12: 12mA
-  - low-power-enable: Flag, power-on-start weak pull-down for invalid power.
-  - low-power-disable: Flag, power-on-start weak pull-down disabled.
-
-Note that many of these properties are only valid for certain specific pins
-or groups. See the TZ1090 TRM for complete details regarding which groups
-support which functionality. The Linux pinctrl driver may also be a useful
-reference.
-
-Valid values for pin and group names are:
-
-  pins:
-
-    These all support bias-high-impediance, bias-pull-up, bias-pull-down, and
-    bias-bus-hold (which can also be provided to any of the groups below to set
-    it for all gpio pins in that group).
-
-    gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data, ext_power.
-
-  mux groups:
-
-    These all support function.
-
-    gpio0
-        pins:       gpio0.
-        function:   ir_mod_stable_out.
-    gpio1
-        pins:       gpio1.
-        function:   ir_mod_power_out.
-
-  drive groups:
-
-    These support input-schmitt-enable, input-schmitt-disable,
-    drive-strength, low-power-enable, and low-power-disable.
-
-    pdc
-        pins:   gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data,
-                ext_power.
-
-Example:
-
-	pinctrl_pdc: pinctrl@2006500 {
-		#gpio-range-cells = <3>;
-		compatible = "img,tz1090-pdc-pinctrl";
-		reg = <0x02006500 0x100>;
-	};
-
-Example board file extracts:
-
-	&pinctrl_pdc {
-		pinctrl-names = "default";
-		pinctrl-0 = <&syswake_default>;
-
-		syswake_default: syswakes {
-			syswake_cfg {
-				tz1090,pins =	"sys_wake0",
-						"sys_wake1",
-						"sys_wake2";
-				pull-up;
-			};
-		};
-		irmod_default: irmod {
-			gpio0_cfg {
-				tz1090,pins =	"gpio0";
-				tz1090,function = "ir_mod_stable_out";
-			};
-			gpio1_cfg {
-				tz1090,pins =	"gpio1";
-				tz1090,function = "ir_mod_power_out";
-			};
-		};
-	};
-
-	ir: ir@2006200 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&irmod_default>;
-	};

Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt

@@ -1,227 +0,0 @@
-ImgTec TZ1090 pin controller
-
-Required properties:
-- compatible: "img,tz1090-pinctrl"
-- reg: Should contain the register physical address and length of the pad
-  configuration registers (CR_PADS_* and CR_IF_CTL0).
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-TZ1090's pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function. For this reason, even seemingly boolean
-values are actually tristates in this binding: unspecified, off, or on.
-Unspecified is represented as an absent property, and off/on are represented as
-integer values 0 and 1.
-
-Required subnode-properties:
-- tz1090,pins : An array of strings. Each string contains the name of a pin or
-  group. Valid values for these names are listed below.
-
-Optional subnode-properties:
-- tz1090,function: A string containing the name of the function to mux to the
-  pin or group. Valid values for function names are listed below, including
-  which pingroups can be muxed to them.
-- supported generic pinconfig properties (for further details see
-  Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt):
-  - bias-disable
-  - bias-high-impedance
-  - bias-bus-hold
-  - bias-pull-up
-  - bias-pull-down
-  - input-schmitt-enable
-  - input-schmitt-disable
-  - drive-strength: Integer, control drive strength of pins in mA.
-      2: 2mA
-      4: 4mA
-      8: 8mA
-      12: 12mA
-
-
-Note that many of these properties are only valid for certain specific pins
-or groups. See the TZ1090 TRM for complete details regarding which groups
-support which functionality. The Linux pinctrl driver may also be a useful
-reference.
-
-Valid values for pin and group names are:
-
-  gpio pins:
-
-    These all support bias-high-impediance, bias-pull-up, bias-pull-down, and
-    bias-bus-hold (which can also be provided to any of the groups below to set
-    it for all pins in that group).
-
-    They also all support the some form of muxing. Any pins which are contained
-    in one of the mux groups (see below) can be muxed only to the functions
-    supported by the mux group. All other pins can be muxed to the "perip"
-    function which enables them with their intended peripheral.
-
-    Different pins in the same mux group cannot be muxed to different functions,
-    however it is possible to mux only a subset of the pins in a mux group to a
-    particular function and leave the remaining pins unmuxed. This is useful if
-    the board connects certain pins in a group to other devices to be controlled
-    by GPIO, and you don't want the usual peripheral to have any control of the
-    pin.
-
-    ant_sel0, ant_sel1, gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7,
-    i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, i2s_lrclk_out,
-    i2s_mclk, pa_on, pdm_a, pdm_b, pdm_c, pdm_d, pll_on, rx_hp, rx_on,
-    scb0_sclk, scb0_sdat, scb1_sclk, scb1_sdat, scb2_sclk, scb2_sdat, sdh_cd,
-    sdh_clk_in, sdh_wp, sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
-    spi0_cs0, spi0_cs1, spi0_cs2, spi0_din, spi0_dout, spi0_mclk, spi1_cs0,
-    spi1_cs1, spi1_cs2, spi1_din, spi1_dout, spi1_mclk, tft_blank_ls, tft_blue0,
-    tft_blue1, tft_blue2, tft_blue3, tft_blue4, tft_blue5, tft_blue6, tft_blue7,
-    tft_green0, tft_green1, tft_green2, tft_green3, tft_green4, tft_green5,
-    tft_green6, tft_green7, tft_hsync_nr, tft_panelclk, tft_pwrsave, tft_red0,
-    tft_red1, tft_red2, tft_red3, tft_red4, tft_red5, tft_red6, tft_red7,
-    tft_vd12acb, tft_vdden_gd, tft_vsync_ns, tx_on, uart0_cts, uart0_rts,
-    uart0_rxd, uart0_txd, uart1_rxd, uart1_txd.
-
-        bias-high-impediance:  supported.
-        bias-pull-up:          supported.
-        bias-pull-down:        supported.
-        bias-bus-hold:         supported.
-        function:              perip or those supported by pin's mux group.
-
-  other pins:
-
-    These other pins are part of various pin groups below, but can't be
-    controlled as GPIOs. They do however support bias-high-impediance,
-    bias-pull-up, bias-pull-down, and bias-bus-hold (which can also be provided
-    to any of the groups below to set it for all pins in that group).
-
-    clk_out0, clk_out1, tck, tdi, tdo, tms, trst.
-
-        bias-high-impediance:  supported.
-        bias-pull-up:          supported.
-        bias-pull-down:        supported.
-        bias-bus-hold:         supported.
-
-  mux groups:
-
-    These all support function, and some support drive configs.
-
-    afe
-        pins:                  tx_on, rx_on, pll_on, pa_on, rx_hp, ant_sel0,
-                               ant_sel1, gain0, gain1, gain2, gain3, gain4,
-                               gain5, gain6, gain7.
-        function:              afe, ts_out_0.
-        input-schmitt-enable:  supported.
-        input-schmitt-disable: supported.
-        drive-strength:        supported.
-    pdm_d
-        pins:                  pdm_d.
-        function:              pdm_dac, usb_vbus.
-    sdh
-        pins:                  sdh_cd, sdh_wp, sdh_clk_in.
-        function:              sdh, sdio.
-    sdio
-        pins:                  sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2,
-                               sdio_d3.
-        function:              sdio, sdh.
-    spi1_cs2
-        pins:                  spi1_cs2.
-        function:              spi1_cs2, usb_vbus.
-    tft
-        pins:                  tft_red0, tft_red1, tft_red2, tft_red3,
-                               tft_red4, tft_red5, tft_red6, tft_red7,
-                               tft_green0, tft_green1, tft_green2, tft_green3,
-                               tft_green4, tft_green5, tft_green6, tft_green7,
-                               tft_blue0, tft_blue1, tft_blue2, tft_blue3,
-                               tft_blue4, tft_blue5, tft_blue6, tft_blue7,
-                               tft_vdden_gd, tft_panelclk, tft_blank_ls,
-                               tft_vsync_ns, tft_hsync_nr, tft_vd12acb,
-                               tft_pwrsave.
-        function:              tft, ext_dac, not_iqadc_stb, iqdac_stb, ts_out_1,
-                               lcd_trace, phy_ringosc.
-        input-schmitt-enable:  supported.
-        input-schmitt-disable: supported.
-        drive-strength:        supported.
-
-  drive groups:
-
-    These all support input-schmitt-enable, input-schmitt-disable,
-    and drive-strength.
-
-    jtag
-        pins:   tck, trst, tdi, tdo, tms.
-    scb1
-        pins:   scb1_sdat, scb1_sclk.
-    scb2
-        pins:   scb2_sdat, scb2_sclk.
-    spi0
-        pins:   spi0_mclk, spi0_cs0, spi0_cs1, spi0_cs2, spi0_dout, spi0_din.
-    spi1
-        pins:   spi1_mclk, spi1_cs0, spi1_cs1, spi1_cs2, spi1_dout, spi1_din.
-    uart
-        pins:   uart0_txd, uart0_rxd, uart0_rts, uart0_cts,
-                uart1_txd, uart1_rxd.
-    drive_i2s
-        pins:   clk_out1, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
-                i2s_lrclk_out, i2s_bclk_out, i2s_mclk.
-    drive_pdm
-        pins:   clk_out0, pdm_b, pdm_a.
-    drive_scb0
-        pins:   scb0_sclk, scb0_sdat, pdm_d, pdm_c.
-    drive_sdio
-        pins:   sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
-                sdh_wp, sdh_cd, sdh_clk_in.
-
-  convenience groups:
-
-    These are just convenient groupings of pins and don't support any drive
-    configs.
-
-    uart0
-        pins:   uart0_cts, uart0_rts, uart0_rxd, uart0_txd.
-    uart1
-        pins:   uart1_rxd, uart1_txd.
-    scb0
-        pins:   scb0_sclk, scb0_sdat.
-    i2s
-        pins:   i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
-                i2s_lrclk_out, i2s_mclk.
-
-Example:
-
-	pinctrl: pinctrl@2005800 {
-		#gpio-range-cells = <3>;
-		compatible = "img,tz1090-pinctrl";
-		reg = <0x02005800 0xe4>;
-	};
-
-Example board file extract:
-
-	&pinctrl {
-		uart0_default: uart0 {
-			uart0_cfg {
-				tz1090,pins =	"uart0_rxd",
-						"uart0_txd";
-				tz1090,function = "perip";
-			};
-		};
-		tft_default: tft {
-			tft_cfg {
-				tz1090,pins =	"tft";
-				tz1090,function = "tft";
-			};
-		};
-	};
-
-	uart@2004b00 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&uart0_default>;
-	};

drivers/pinctrl/Kconfig

@@ -263,18 +263,6 @@ config PINCTRL_ST
 	select PINCONF
 	select GPIOLIB_IRQCHIP
 
-config PINCTRL_TZ1090
-	bool "Toumaz Xenif TZ1090 pin control driver"
-	depends on SOC_TZ1090
-	select PINMUX
-	select GENERIC_PINCONF
-
-config PINCTRL_TZ1090_PDC
-	bool "Toumaz Xenif TZ1090 PDC pin control driver"
-	depends on SOC_TZ1090
-	select PINMUX
-	select PINCONF
-
 config PINCTRL_U300
 	bool "U300 pin controller driver"
 	depends on ARCH_U300

drivers/pinctrl/Makefile

@@ -34,8 +34,6 @@ obj-$(CONFIG_PINCTRL_SINGLE)	+= pinctrl-single.o
 obj-$(CONFIG_PINCTRL_SIRF)	+= sirf/
 obj-$(CONFIG_PINCTRL_SX150X)	+= pinctrl-sx150x.o
 obj-$(CONFIG_ARCH_TEGRA)	+= tegra/
-obj-$(CONFIG_PINCTRL_TZ1090)	+= pinctrl-tz1090.o
-obj-$(CONFIG_PINCTRL_TZ1090_PDC)	+= pinctrl-tz1090-pdc.o
 obj-$(CONFIG_PINCTRL_U300)	+= pinctrl-u300.o
 obj-$(CONFIG_PINCTRL_COH901)	+= pinctrl-coh901.o
 obj-$(CONFIG_PINCTRL_XWAY)	+= pinctrl-xway.o

drivers/pinctrl/pinctrl-tz1090-pdc.c

@@ -1,989 +0,0 @@
-/*
- * Pinctrl driver for the Toumaz Xenif TZ1090 PowerDown Controller pins
- *
- * Copyright (c) 2013, Imagination Technologies Ltd.
- *
- * Derived from Tegra code:
- * Copyright (c) 2011-2012, NVIDIA CORPORATION.  All rights reserved.
- *
- * Derived from code:
- * Copyright (C) 2010 Google, Inc.
- * Copyright (C) 2010 NVIDIA Corporation
- * Copyright (C) 2009-2011 ST-Ericsson AB
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
- * more details.
- */
-
-#include <linux/bitops.h>
-#include <linux/io.h>
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/platform_device.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/pinctrl/pinconf-generic.h>
-#include <linux/pinctrl/pinctrl.h>
-#include <linux/pinctrl/pinmux.h>
-#include <linux/slab.h>
-
-/*
- * The registers may be shared with other threads/cores, so we need to use the
- * metag global lock2 for atomicity.
- */
-#include <asm/global_lock.h>
-
-#include "core.h"
-#include "pinconf.h"
-
-/* Register offsets from bank base address */
-#define REG_GPIO_CONTROL0	0x00
-#define REG_GPIO_CONTROL2	0x08
-
-/* Register field information */
-#define REG_GPIO_CONTROL2_PU_PD_S	16
-#define REG_GPIO_CONTROL2_PDC_POS_S	 4
-#define REG_GPIO_CONTROL2_PDC_DR_S	 2
-#define REG_GPIO_CONTROL2_PDC_SR_S	 1
-#define REG_GPIO_CONTROL2_PDC_SCHMITT_S	 0
-
-/* PU_PD field values */
-#define REG_PU_PD_TRISTATE	0
-#define REG_PU_PD_UP		1
-#define REG_PU_PD_DOWN		2
-#define REG_PU_PD_REPEATER	3
-
-/* DR field values */
-#define REG_DR_2mA		0
-#define REG_DR_4mA		1
-#define REG_DR_8mA		2
-#define REG_DR_12mA		3
-
-/**
- * struct tz1090_pdc_function - TZ1090 PDC pinctrl mux function
- * @name:	The name of the function, exported to pinctrl core.
- * @groups:	An array of pin groups that may select this function.
- * @ngroups:	The number of entries in @groups.
- */
-struct tz1090_pdc_function {
-	const char		*name;
-	const char * const	*groups;
-	unsigned int		ngroups;
-};
-
-/**
- * struct tz1090_pdc_pingroup - TZ1090 PDC pin group
- * @name:	Name of pin group.
- * @pins:	Array of pin numbers in this pin group.
- * @npins:	Number of pins in this pin group.
- * @func:	Function enabled by the mux.
- * @reg:	Mux register offset.
- * @bit:	Mux register bit.
- * @drv:	Drive control supported, otherwise it's a mux.
- *		This means Schmitt, Slew, and Drive strength.
- *
- * A representation of a group of pins (possibly just one pin) in the TZ1090
- * PDC pin controller. Each group allows some parameter or parameters to be
- * configured. The most common is mux function selection.
- */
-struct tz1090_pdc_pingroup {
-	const char		*name;
-	const unsigned int	*pins;
-	unsigned int		npins;
-	int			func;
-	u16			reg;
-	u8			bit;
-	bool			drv;
-};
-
-/*
- * All PDC pins can be GPIOs. Define these first to match how the GPIO driver
- * names/numbers its pins.
- */
-
-enum tz1090_pdc_pin {
-	TZ1090_PDC_PIN_GPIO0,
-	TZ1090_PDC_PIN_GPIO1,
-	TZ1090_PDC_PIN_SYS_WAKE0,
-	TZ1090_PDC_PIN_SYS_WAKE1,
-	TZ1090_PDC_PIN_SYS_WAKE2,
-	TZ1090_PDC_PIN_IR_DATA,
-	TZ1090_PDC_PIN_EXT_POWER,
-};
-
-/* Pin names */
-
-static const struct pinctrl_pin_desc tz1090_pdc_pins[] = {
-	/* PDC GPIOs */
-	PINCTRL_PIN(TZ1090_PDC_PIN_GPIO0,	"gpio0"),
-	PINCTRL_PIN(TZ1090_PDC_PIN_GPIO1,	"gpio1"),
-	PINCTRL_PIN(TZ1090_PDC_PIN_SYS_WAKE0,	"sys_wake0"),
-	PINCTRL_PIN(TZ1090_PDC_PIN_SYS_WAKE1,	"sys_wake1"),
-	PINCTRL_PIN(TZ1090_PDC_PIN_SYS_WAKE2,	"sys_wake2"),
-	PINCTRL_PIN(TZ1090_PDC_PIN_IR_DATA,	"ir_data"),
-	PINCTRL_PIN(TZ1090_PDC_PIN_EXT_POWER,	"ext_power"),
-};
-
-/* Pin group pins */
-
-static const unsigned int gpio0_pins[] = {
-	TZ1090_PDC_PIN_GPIO0,
-};
-
-static const unsigned int gpio1_pins[] = {
-	TZ1090_PDC_PIN_GPIO1,
-};
-
-static const unsigned int pdc_pins[] = {
-	TZ1090_PDC_PIN_GPIO0,
-	TZ1090_PDC_PIN_GPIO1,
-	TZ1090_PDC_PIN_SYS_WAKE0,
-	TZ1090_PDC_PIN_SYS_WAKE1,
-	TZ1090_PDC_PIN_SYS_WAKE2,
-	TZ1090_PDC_PIN_IR_DATA,
-	TZ1090_PDC_PIN_EXT_POWER,
-};
-
-/* Mux functions */
-
-enum tz1090_pdc_mux {
-	/* PDC_GPIO0 mux */
-	TZ1090_PDC_MUX_IR_MOD_STABLE_OUT,
-	/* PDC_GPIO1 mux */
-	TZ1090_PDC_MUX_IR_MOD_POWER_OUT,
-};
-
-/* Pin groups a function can be muxed to */
-
-static const char * const gpio0_groups[] = {
-	"gpio0",
-};
-
-static const char * const gpio1_groups[] = {
-	"gpio1",
-};
-
-#define FUNCTION(mux, fname, group)			\
-	[(TZ1090_PDC_MUX_ ## mux)] = {			\
-		.name = #fname,				\
-		.groups = group##_groups,		\
-		.ngroups = ARRAY_SIZE(group##_groups),	\
-	}
-
-/* Must correlate with enum tz1090_pdc_mux */
-static const struct tz1090_pdc_function tz1090_pdc_functions[] = {
-	/*	 MUX			fn			pingroups */
-	FUNCTION(IR_MOD_STABLE_OUT,	ir_mod_stable_out,	gpio0),
-	FUNCTION(IR_MOD_POWER_OUT,	ir_mod_power_out,	gpio1),
-};
-
-/**
- * MUX_PG() - Initialise a pin group with mux control
- * @pg_name:	Pin group name (stringified, _pins appended to get pins array)
- * @f0:		Function 0 (TZ1090_PDC_MUX_ is prepended)
- * @mux_r:	Mux register (REG_PINCTRL_ is prepended)
- * @mux_b:	Bit number in register of mux field
- */
-#define MUX_PG(pg_name, f0, mux_r, mux_b)			\
-	{							\
-		.name = #pg_name,				\
-		.pins = pg_name##_pins,				\
-		.npins = ARRAY_SIZE(pg_name##_pins),		\
-		.func = TZ1090_PDC_MUX_ ## f0,			\
-		.reg = (REG_ ## mux_r),				\
-		.bit = (mux_b),					\
-	}
-
-/**
- * DRV_PG() - Initialise a pin group with drive control
- * @pg_name:	Pin group name (stringified, _pins appended to get pins array)
- */
-#define DRV_PG(pg_name)				\
-	{							\
-		.name = #pg_name,				\
-		.pins = pg_name##_pins,				\
-		.npins = ARRAY_SIZE(pg_name##_pins),		\
-		.drv = true,					\
-	}
-
-static const struct tz1090_pdc_pingroup tz1090_pdc_groups[] = {
-	/* Muxing pin groups */
-	/*     pg_name, f0,                 mux register,  mux bit */
-	MUX_PG(gpio0,   IR_MOD_STABLE_OUT,  GPIO_CONTROL0, 7),
-	MUX_PG(gpio1,   IR_MOD_POWER_OUT,   GPIO_CONTROL0, 6),
-
-	/* Drive pin groups */
-	/*     pg_name */
-	DRV_PG(pdc),
-};
-
-/**
- * struct tz1090_pdc_pmx - Private pinctrl data
- * @dev:	Platform device
- * @pctl:	Pin control device
- * @regs:	Register region
- * @lock:	Lock protecting coherency of mux_en and gpio_en
- * @mux_en:	Muxes that have been enabled
- * @gpio_en:	Muxable GPIOs that have been enabled
- */
-struct tz1090_pdc_pmx {
-	struct device		*dev;
-	struct pinctrl_dev	*pctl;
-	void __iomem		*regs;
-	spinlock_t		lock;
-	u32			mux_en;
-	u32			gpio_en;
-};
-
-static inline u32 pmx_read(struct tz1090_pdc_pmx *pmx, u32 reg)
-{
-	return ioread32(pmx->regs + reg);
-}
-
-static inline void pmx_write(struct tz1090_pdc_pmx *pmx, u32 val, u32 reg)
-{
-	iowrite32(val, pmx->regs + reg);
-}
-
-/*
- * Pin control operations
- */
-
-static int tz1090_pdc_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
-{
-	return ARRAY_SIZE(tz1090_pdc_groups);
-}
-
-static const char *tz1090_pdc_pinctrl_get_group_name(struct pinctrl_dev *pctl,
-						     unsigned int group)
-{
-	return tz1090_pdc_groups[group].name;
-}
-
-static int tz1090_pdc_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
-					     unsigned int group,
-					     const unsigned int **pins,
-					     unsigned int *num_pins)
-{
-	*pins = tz1090_pdc_groups[group].pins;
-	*num_pins = tz1090_pdc_groups[group].npins;
-
-	return 0;
-}
-
-#ifdef CONFIG_DEBUG_FS
-static void tz1090_pdc_pinctrl_pin_dbg_show(struct pinctrl_dev *pctldev,
-					    struct seq_file *s,
-					    unsigned int offset)
-{
-	seq_printf(s, " %s", dev_name(pctldev->dev));
-}
-#endif
-
-static int reserve_map(struct device *dev, struct pinctrl_map **map,
-		       unsigned int *reserved_maps, unsigned int *num_maps,
-		       unsigned int reserve)
-{
-	unsigned int old_num = *reserved_maps;
-	unsigned int new_num = *num_maps + reserve;
-	struct pinctrl_map *new_map;
-
-	if (old_num >= new_num)
-		return 0;
-
-	new_map = krealloc(*map, sizeof(*new_map) * new_num, GFP_KERNEL);
-	if (!new_map) {
-		dev_err(dev, "krealloc(map) failed\n");
-		return -ENOMEM;
-	}
-
-	memset(new_map + old_num, 0, (new_num - old_num) * sizeof(*new_map));
-
-	*map = new_map;
-	*reserved_maps = new_num;
-
-	return 0;
-}
-
-static int add_map_mux(struct pinctrl_map **map, unsigned int *reserved_maps,
-		       unsigned int *num_maps, const char *group,
-		       const char *function)
-{
-	if (WARN_ON(*num_maps == *reserved_maps))
-		return -ENOSPC;
-
-	(*map)[*num_maps].type = PIN_MAP_TYPE_MUX_GROUP;
-	(*map)[*num_maps].data.mux.group = group;
-	(*map)[*num_maps].data.mux.function = function;
-	(*num_maps)++;
-
-	return 0;
-}
-
-/**
- * get_group_selector() - returns the group selector for a group
- * @pin_group: the pin group to look up
- *
- * This is the same as pinctrl_get_group_selector except it doesn't produce an
- * error message if the group isn't found or debug messages.
- */
-static int get_group_selector(const char *pin_group)
-{
-	unsigned int group;
-
-	for (group = 0; group < ARRAY_SIZE(tz1090_pdc_groups); ++group)
-		if (!strcmp(tz1090_pdc_groups[group].name, pin_group))
-			return group;
-
-	return -EINVAL;
-}
-
-static int add_map_configs(struct device *dev,
-			   struct pinctrl_map **map,
-			   unsigned int *reserved_maps, unsigned int *num_maps,
-			   const char *group, unsigned long *configs,
-			   unsigned int num_configs)
-{
-	unsigned long *dup_configs;
-	enum pinctrl_map_type type;
-
-	if (WARN_ON(*num_maps == *reserved_maps))
-		return -ENOSPC;
-
-	dup_configs = kmemdup(configs, num_configs * sizeof(*dup_configs),
-			      GFP_KERNEL);
-	if (!dup_configs)
-		return -ENOMEM;
-
-	/*
-	 * We support both pins and pin groups, but we need to figure out which
-	 * one we have.
-	 */
-	if (get_group_selector(group) >= 0)
-		type = PIN_MAP_TYPE_CONFIGS_GROUP;
-	else
-		type = PIN_MAP_TYPE_CONFIGS_PIN;
-	(*map)[*num_maps].type = type;
-	(*map)[*num_maps].data.configs.group_or_pin = group;
-	(*map)[*num_maps].data.configs.configs = dup_configs;
-	(*map)[*num_maps].data.configs.num_configs = num_configs;
-	(*num_maps)++;
-
-	return 0;
-}
-
-static void tz1090_pdc_pinctrl_dt_free_map(struct pinctrl_dev *pctldev,
-					   struct pinctrl_map *map,
-					   unsigned int num_maps)
-{
-	int i;
-
-	for (i = 0; i < num_maps; i++)
-		if (map[i].type == PIN_MAP_TYPE_CONFIGS_GROUP)
-			kfree(map[i].data.configs.configs);
-
-	kfree(map);
-}
-
-static int tz1090_pdc_pinctrl_dt_subnode_to_map(struct device *dev,
-						struct device_node *np,
-						struct pinctrl_map **map,
-						unsigned int *reserved_maps,
-						unsigned int *num_maps)
-{
-	int ret;
-	const char *function;
-	unsigned long *configs = NULL;
-	unsigned int num_configs = 0;
-	unsigned int reserve;
-	struct property *prop;
-	const char *group;
-
-	ret = of_property_read_string(np, "tz1090,function", &function);
-	if (ret < 0) {
-		/* EINVAL=missing, which is fine since it's optional */
-		if (ret != -EINVAL)
-			dev_err(dev,
-				"could not parse property function\n");
-		function = NULL;
-	}
-
-	ret = pinconf_generic_parse_dt_config(np, NULL, &configs, &num_configs);
-	if (ret)
-		return ret;
-
-	reserve = 0;
-	if (function != NULL)
-		reserve++;
-	if (num_configs)
-		reserve++;
-	ret = of_property_count_strings(np, "tz1090,pins");
-	if (ret < 0) {
-		dev_err(dev, "could not parse property pins\n");
-		goto exit;
-	}
-	reserve *= ret;
-
-	ret = reserve_map(dev, map, reserved_maps, num_maps, reserve);
-	if (ret < 0)
-		goto exit;
-
-	of_property_for_each_string(np, "tz1090,pins", prop, group) {
-		if (function) {
-			ret = add_map_mux(map, reserved_maps, num_maps,
-					  group, function);
-			if (ret < 0)
-				goto exit;
-		}
-
-		if (num_configs) {
-			ret = add_map_configs(dev, map, reserved_maps,
-					      num_maps, group, configs,
-					      num_configs);
-			if (ret < 0)
-				goto exit;
-		}
-	}
-
-	ret = 0;
-
-exit:
-	kfree(configs);
-	return ret;
-}
-
-static int tz1090_pdc_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev,
-					     struct device_node *np_config,
-					     struct pinctrl_map **map,
-					     unsigned int *num_maps)
-{
-	unsigned int reserved_maps;
-	struct device_node *np;
-	int ret;
-
-	reserved_maps = 0;
-	*map = NULL;
-	*num_maps = 0;
-
-	for_each_child_of_node(np_config, np) {
-		ret = tz1090_pdc_pinctrl_dt_subnode_to_map(pctldev->dev, np,
-							   map, &reserved_maps,
-							   num_maps);
-		if (ret < 0) {
-			tz1090_pdc_pinctrl_dt_free_map(pctldev, *map,
-						       *num_maps);
-			return ret;
-		}
-	}
-
-	return 0;
-}
-
-static const struct pinctrl_ops tz1090_pdc_pinctrl_ops = {
-	.get_groups_count	= tz1090_pdc_pinctrl_get_groups_count,
-	.get_group_name		= tz1090_pdc_pinctrl_get_group_name,
-	.get_group_pins		= tz1090_pdc_pinctrl_get_group_pins,
-#ifdef CONFIG_DEBUG_FS
-	.pin_dbg_show		= tz1090_pdc_pinctrl_pin_dbg_show,
-#endif
-	.dt_node_to_map		= tz1090_pdc_pinctrl_dt_node_to_map,
-	.dt_free_map		= tz1090_pdc_pinctrl_dt_free_map,
-};
-
-/*
- * Pin mux operations
- */
-
-static int tz1090_pdc_pinctrl_get_funcs_count(struct pinctrl_dev *pctldev)
-{
-	return ARRAY_SIZE(tz1090_pdc_functions);
-}
-
-static const char *tz1090_pdc_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
-						    unsigned int function)
-{
-	return tz1090_pdc_functions[function].name;
-}
-
-static int tz1090_pdc_pinctrl_get_func_groups(struct pinctrl_dev *pctldev,
-					      unsigned int function,
-					      const char * const **groups,
-					      unsigned int * const num_groups)
-{
-	*groups = tz1090_pdc_functions[function].groups;
-	*num_groups = tz1090_pdc_functions[function].ngroups;
-
-	return 0;
-}
-
-/**
- * tz1090_pdc_pinctrl_mux() - update mux bit
- * @pmx:		Pinmux data
- * @grp:		Pin mux group
- */
-static void tz1090_pdc_pinctrl_mux(struct tz1090_pdc_pmx *pmx,
-				   const struct tz1090_pdc_pingroup *grp)
-{
-	u32 reg, select;
-	unsigned int pin_shift = grp->pins[0];
-	unsigned long flags;
-
-	/* select = mux && !gpio */
-	select = ((pmx->mux_en & ~pmx->gpio_en) >> pin_shift) & 1;
-
-	/* set up the mux */
-	__global_lock2(flags);
-	reg = pmx_read(pmx, grp->reg);
-	reg &= ~BIT(grp->bit);
-	reg |= select << grp->bit;
-	pmx_write(pmx, reg, grp->reg);
-	__global_unlock2(flags);
-}
-
-static int tz1090_pdc_pinctrl_set_mux(struct pinctrl_dev *pctldev,
-				      unsigned int function,
-				      unsigned int group)
-{
-	struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	const struct tz1090_pdc_pingroup *grp = &tz1090_pdc_groups[group];
-
-	dev_dbg(pctldev->dev, "%s(func=%u (%s), group=%u (%s))\n",
-		__func__,
-		function, tz1090_pdc_functions[function].name,
-		group, tz1090_pdc_groups[group].name);
-
-	/* is it even a mux? */
-	if (grp->drv)
-		return -EINVAL;
-
-	/* does this group even control the function? */
-	if (function != grp->func)
-		return -EINVAL;
-
-	/* record the pin being muxed and update mux bit */
-	spin_lock(&pmx->lock);
-	pmx->mux_en |= BIT(grp->pins[0]);
-	tz1090_pdc_pinctrl_mux(pmx, grp);
-	spin_unlock(&pmx->lock);
-	return 0;
-}
-
-static const struct tz1090_pdc_pingroup *find_mux_group(
-						struct tz1090_pdc_pmx *pmx,
-						unsigned int pin)
-{
-	const struct tz1090_pdc_pingroup *grp;
-	unsigned int group;
-
-	grp = tz1090_pdc_groups;
-	for (group = 0; group < ARRAY_SIZE(tz1090_pdc_groups); ++group, ++grp) {
-		/* only match muxes */
-		if (grp->drv)
-			continue;
-
-		/* with a matching pin */
-		if (grp->pins[0] == pin)
-			return grp;
-	}
-
-	return NULL;
-}
-
-static int tz1090_pdc_pinctrl_gpio_request_enable(
-					struct pinctrl_dev *pctldev,
-					struct pinctrl_gpio_range *range,
-					unsigned int pin)
-{
-	struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	const struct tz1090_pdc_pingroup *grp = find_mux_group(pmx, pin);
-
-	if (grp) {
-		/* record the pin in GPIO use and update mux bit */
-		spin_lock(&pmx->lock);
-		pmx->gpio_en |= BIT(pin);
-		tz1090_pdc_pinctrl_mux(pmx, grp);
-		spin_unlock(&pmx->lock);
-	}
-	return 0;
-}
-
-static void tz1090_pdc_pinctrl_gpio_disable_free(
-					struct pinctrl_dev *pctldev,
-					struct pinctrl_gpio_range *range,
-					unsigned int pin)
-{
-	struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	const struct tz1090_pdc_pingroup *grp = find_mux_group(pmx, pin);
-
-	if (grp) {
-		/* record the pin not in GPIO use and update mux bit */
-		spin_lock(&pmx->lock);
-		pmx->gpio_en &= ~BIT(pin);
-		tz1090_pdc_pinctrl_mux(pmx, grp);
-		spin_unlock(&pmx->lock);
-	}
-}
-
-static const struct pinmux_ops tz1090_pdc_pinmux_ops = {
-	.get_functions_count	= tz1090_pdc_pinctrl_get_funcs_count,
-	.get_function_name	= tz1090_pdc_pinctrl_get_func_name,
-	.get_function_groups	= tz1090_pdc_pinctrl_get_func_groups,
-	.set_mux		= tz1090_pdc_pinctrl_set_mux,
-	.gpio_request_enable	= tz1090_pdc_pinctrl_gpio_request_enable,
-	.gpio_disable_free	= tz1090_pdc_pinctrl_gpio_disable_free,
-};
-
-/*
- * Pin config operations
- */
-
-static int tz1090_pdc_pinconf_reg(struct pinctrl_dev *pctldev,
-				  unsigned int pin,
-				  enum pin_config_param param,
-				  bool report_err,
-				  u32 *reg, u32 *width, u32 *mask, u32 *shift,
-				  u32 *val)
-{
-	/* Find information about parameter's register */
-	switch (param) {
-	case PIN_CONFIG_BIAS_DISABLE:
-	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
-		*val = REG_PU_PD_TRISTATE;
-		break;
-	case PIN_CONFIG_BIAS_PULL_UP:
-		*val = REG_PU_PD_UP;
-		break;
-	case PIN_CONFIG_BIAS_PULL_DOWN:
-		*val = REG_PU_PD_DOWN;
-		break;
-	case PIN_CONFIG_BIAS_BUS_HOLD:
-		*val = REG_PU_PD_REPEATER;
-		break;
-	default:
-		return -ENOTSUPP;
-	}
-
-	/* Only input bias parameters supported */
-	*reg = REG_GPIO_CONTROL2;
-	*shift = REG_GPIO_CONTROL2_PU_PD_S + pin*2;
-	*width = 2;
-
-	/* Calculate field information */
-	*mask = (BIT(*width) - 1) << *shift;
-
-	return 0;
-}
-
-static int tz1090_pdc_pinconf_get(struct pinctrl_dev *pctldev,
-				  unsigned int pin, unsigned long *config)
-{
-	struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	enum pin_config_param param = pinconf_to_config_param(*config);
-	int ret;
-	u32 reg, width, mask, shift, val, tmp, arg;
-
-	/* Get register information */
-	ret = tz1090_pdc_pinconf_reg(pctldev, pin, param, true,
-				     &reg, &width, &mask, &shift, &val);
-	if (ret < 0)
-		return ret;
-
-	/* Extract field from register */
-	tmp = pmx_read(pmx, reg);
-	arg = ((tmp & mask) >> shift) == val;
-
-	/* Config not active */
-	if (!arg)
-		return -EINVAL;
-
-	/* And pack config */
-	*config = pinconf_to_config_packed(param, arg);
-
-	return 0;
-}
-
-static int tz1090_pdc_pinconf_set(struct pinctrl_dev *pctldev,
-				  unsigned int pin, unsigned long *configs,
-				  unsigned num_configs)
-{
-	struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	enum pin_config_param param;
-	unsigned int arg;
-	int ret;
-	u32 reg, width, mask, shift, val, tmp;
-	unsigned long flags;
-	int i;
-
-	for (i = 0; i < num_configs; i++) {
-		param = pinconf_to_config_param(configs[i]);
-		arg = pinconf_to_config_argument(configs[i]);
-
-		dev_dbg(pctldev->dev, "%s(pin=%s, config=%#lx)\n",
-			__func__, tz1090_pdc_pins[pin].name, configs[i]);
-
-		/* Get register information */
-		ret = tz1090_pdc_pinconf_reg(pctldev, pin, param, true,
-					     &reg, &width, &mask, &shift, &val);
-		if (ret < 0)
-			return ret;
-
-		/* Unpack argument and range check it */
-		if (arg > 1) {
-			dev_dbg(pctldev->dev, "%s: arg %u out of range\n",
-				__func__, arg);
-			return -EINVAL;
-		}
-
-		/* Write register field */
-		__global_lock2(flags);
-		tmp = pmx_read(pmx, reg);
-		tmp &= ~mask;
-		if (arg)
-			tmp |= val << shift;
-		pmx_write(pmx, tmp, reg);
-		__global_unlock2(flags);
-	} /* for each config */
-
-	return 0;
-}
-
-static const int tz1090_pdc_boolean_map[] = {
-	[0]		= -EINVAL,
-	[1]		= 1,
-};
-
-static const int tz1090_pdc_dr_map[] = {
-	[REG_DR_2mA]	= 2,
-	[REG_DR_4mA]	= 4,
-	[REG_DR_8mA]	= 8,
-	[REG_DR_12mA]	= 12,
-};
-
-static int tz1090_pdc_pinconf_group_reg(struct pinctrl_dev *pctldev,
-					const struct tz1090_pdc_pingroup *g,
-					enum pin_config_param param,
-					bool report_err, u32 *reg, u32 *width,
-					u32 *mask, u32 *shift, const int **map)
-{
-	/* Drive configuration applies in groups, but not to all groups. */
-	if (!g->drv) {
-		if (report_err)
-			dev_dbg(pctldev->dev,
-				"%s: group %s has no drive control\n",
-				__func__, g->name);
-		return -ENOTSUPP;
-	}
-
-	/* Find information about drive parameter's register */
-	*reg = REG_GPIO_CONTROL2;
-	switch (param) {
-	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
-		*shift = REG_GPIO_CONTROL2_PDC_SCHMITT_S;
-		*width = 1;
-		*map = tz1090_pdc_boolean_map;
-		break;
-	case PIN_CONFIG_DRIVE_STRENGTH:
-		*shift = REG_GPIO_CONTROL2_PDC_DR_S;
-		*width = 2;
-		*map = tz1090_pdc_dr_map;
-		break;
-	case PIN_CONFIG_LOW_POWER_MODE:
-		*shift = REG_GPIO_CONTROL2_PDC_POS_S;
-		*width = 1;
-		*map = tz1090_pdc_boolean_map;
-		break;
-	default:
-		return -ENOTSUPP;
-	}
-
-	/* Calculate field information */
-	*mask = (BIT(*width) - 1) << *shift;
-
-	return 0;
-}
-
-static int tz1090_pdc_pinconf_group_get(struct pinctrl_dev *pctldev,
-					unsigned int group,
-					unsigned long *config)
-{
-	struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	const struct tz1090_pdc_pingroup *g = &tz1090_pdc_groups[group];
-	enum pin_config_param param = pinconf_to_config_param(*config);
-	int ret, arg;
-	u32 reg, width, mask, shift, val;
-	const int *map;
-
-	/* Get register information */
-	ret = tz1090_pdc_pinconf_group_reg(pctldev, g, param, true,
-					   &reg, &width, &mask, &shift, &map);
-	if (ret < 0)
-		return ret;
-
-	/* Extract field from register */
-	val = pmx_read(pmx, reg);
-	arg = map[(val & mask) >> shift];
-	if (arg < 0)
-		return arg;
-
-	/* And pack config */
-	*config = pinconf_to_config_packed(param, arg);
-
-	return 0;
-}
-
-static int tz1090_pdc_pinconf_group_set(struct pinctrl_dev *pctldev,
-					unsigned int group,
-					unsigned long *configs,
-					unsigned num_configs)
-{
-	struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	const struct tz1090_pdc_pingroup *g = &tz1090_pdc_groups[group];
-	enum pin_config_param param;
-	const unsigned int *pit;
-	unsigned int i;
-	int ret, arg;
-	u32 reg, width, mask, shift, val;
-	unsigned long flags;
-	const int *map;
-	int j;
-
-	for (j = 0; j < num_configs; j++) {
-		param = pinconf_to_config_param(configs[j]);
-
-		dev_dbg(pctldev->dev, "%s(group=%s, config=%#lx)\n",
-			__func__, g->name, configs[j]);
-
-		/* Get register information */
-		ret = tz1090_pdc_pinconf_group_reg(pctldev, g, param, true,
-						   &reg, &width, &mask, &shift,
-						   &map);
-		if (ret < 0) {
-			/*
-			 * Maybe we're trying to set a per-pin configuration
-			 * of a group, so do the pins one by one. This is
-			 * mainly as a convenience.
-			 */
-			for (i = 0, pit = g->pins; i < g->npins; ++i, ++pit) {
-				ret = tz1090_pdc_pinconf_set(pctldev, *pit,
-					configs, num_configs);
-				if (ret)
-					return ret;
-			}
-			return 0;
-		}
-
-		/* Unpack argument and map it to register value */
-		arg = pinconf_to_config_argument(configs[j]);
-		for (i = 0; i < BIT(width); ++i) {
-			if (map[i] == arg || (map[i] == -EINVAL && !arg)) {
-				/* Write register field */
-				__global_lock2(flags);
-				val = pmx_read(pmx, reg);
-				val &= ~mask;
-				val |= i << shift;
-				pmx_write(pmx, val, reg);
-				__global_unlock2(flags);
-				goto next_config;
-			}
-		}
-
-		dev_dbg(pctldev->dev, "%s: arg %u not supported\n",
-			__func__, arg);
-		return 0;
-
-next_config:
-		;
-	} /* for each config */
-
-	return 0;
-}
-
-static const struct pinconf_ops tz1090_pdc_pinconf_ops = {
-	.is_generic			= true,
-	.pin_config_get			= tz1090_pdc_pinconf_get,
-	.pin_config_set			= tz1090_pdc_pinconf_set,
-	.pin_config_group_get		= tz1090_pdc_pinconf_group_get,
-	.pin_config_group_set		= tz1090_pdc_pinconf_group_set,
-	.pin_config_config_dbg_show	= pinconf_generic_dump_config,
-};
-
-/*
- * Pin control driver setup
- */
-
-static struct pinctrl_desc tz1090_pdc_pinctrl_desc = {
-	.pctlops	= &tz1090_pdc_pinctrl_ops,
-	.pmxops		= &tz1090_pdc_pinmux_ops,
-	.confops	= &tz1090_pdc_pinconf_ops,
-	.owner		= THIS_MODULE,
-};
-
-static int tz1090_pdc_pinctrl_probe(struct platform_device *pdev)
-{
-	struct tz1090_pdc_pmx *pmx;
-	struct resource *res;
-
-	pmx = devm_kzalloc(&pdev->dev, sizeof(*pmx), GFP_KERNEL);
-	if (!pmx)
-		return -ENOMEM;
-
-	pmx->dev = &pdev->dev;
-	spin_lock_init(&pmx->lock);
-
-	tz1090_pdc_pinctrl_desc.name = dev_name(&pdev->dev);
-	tz1090_pdc_pinctrl_desc.pins = tz1090_pdc_pins;
-	tz1090_pdc_pinctrl_desc.npins = ARRAY_SIZE(tz1090_pdc_pins);
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	pmx->regs = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(pmx->regs))
-		return PTR_ERR(pmx->regs);
-
-	pmx->pctl = devm_pinctrl_register(&pdev->dev, &tz1090_pdc_pinctrl_desc,
-					  pmx);
-	if (IS_ERR(pmx->pctl)) {
-		dev_err(&pdev->dev, "Couldn't register pinctrl driver\n");
-		return PTR_ERR(pmx->pctl);
-	}
-
-	platform_set_drvdata(pdev, pmx);
-
-	dev_info(&pdev->dev, "TZ1090 PDC pinctrl driver initialised\n");
-
-	return 0;
-}
-
-static const struct of_device_id tz1090_pdc_pinctrl_of_match[] = {
-	{ .compatible = "img,tz1090-pdc-pinctrl", },
-	{ },
-};
-
-static struct platform_driver tz1090_pdc_pinctrl_driver = {
-	.driver = {
-		.name		= "tz1090-pdc-pinctrl",
-		.of_match_table	= tz1090_pdc_pinctrl_of_match,
-	},
-	.probe	= tz1090_pdc_pinctrl_probe,
-};
-
-static int __init tz1090_pdc_pinctrl_init(void)
-{
-	return platform_driver_register(&tz1090_pdc_pinctrl_driver);
-}
-arch_initcall(tz1090_pdc_pinctrl_init);
-
-static void __exit tz1090_pdc_pinctrl_exit(void)
-{
-	platform_driver_unregister(&tz1090_pdc_pinctrl_driver);
-}
-module_exit(tz1090_pdc_pinctrl_exit);
-
-MODULE_AUTHOR("Imagination Technologies Ltd.");
-MODULE_DESCRIPTION("Toumaz Xenif TZ1090 PDC pinctrl driver");
-MODULE_LICENSE("GPL v2");
-MODULE_DEVICE_TABLE(of, tz1090_pdc_pinctrl_of_match);

drivers/pinctrl/pinctrl-tz1090.c

@@ -1,2005 +0,0 @@
-/*
- * Pinctrl driver for the Toumaz Xenif TZ1090 SoC
- *
- * Copyright (c) 2013, Imagination Technologies Ltd.
- *
- * Derived from Tegra code:
- * Copyright (c) 2011-2012, NVIDIA CORPORATION.  All rights reserved.
- *
- * Derived from code:
- * Copyright (C) 2010 Google, Inc.
- * Copyright (C) 2010 NVIDIA Corporation
- * Copyright (C) 2009-2011 ST-Ericsson AB
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
- * more details.
- */
-
-#include <linux/bitops.h>
-#include <linux/io.h>
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/platform_device.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/pinctrl/pinconf-generic.h>
-#include <linux/pinctrl/pinctrl.h>
-#include <linux/pinctrl/pinmux.h>
-#include <linux/slab.h>
-#include <linux/spinlock.h>
-
-/*
- * The registers may be shared with other threads/cores, so we need to use the
- * metag global lock2 for atomicity.
- */
-#include <asm/global_lock.h>
-
-#include "core.h"
-#include "pinconf.h"
-
-/* Register offsets from bank base address */
-#define REG_PINCTRL_SELECT	0x10
-#define REG_PINCTRL_SCHMITT	0x90
-#define REG_PINCTRL_PU_PD	0xa0
-#define REG_PINCTRL_SR		0xc0
-#define REG_PINCTRL_DR		0xd0
-#define REG_PINCTRL_IF_CTL	0xe0
-
-/* REG_PINCTRL_PU_PD field values */
-#define REG_PU_PD_TRISTATE	0
-#define REG_PU_PD_UP		1
-#define REG_PU_PD_DOWN		2
-#define REG_PU_PD_REPEATER	3
-
-/* REG_PINCTRL_DR field values */
-#define REG_DR_2mA		0
-#define REG_DR_4mA		1
-#define REG_DR_8mA		2
-#define REG_DR_12mA		3
-
-/**
- * struct tz1090_function - TZ1090 pinctrl mux function
- * @name:	The name of the function, exported to pinctrl core.
- * @groups:	An array of pin groups that may select this function.
- * @ngroups:	The number of entries in @groups.
- */
-struct tz1090_function {
-	const char		*name;
-	const char * const	*groups;
-	unsigned int		ngroups;
-};
-
-/**
- * struct tz1090_muxdesc - TZ1090 individual mux description
- * @funcs:	Function for each mux value.
- * @reg:	Mux register offset. 0 if unsupported.
- * @bit:	Mux register bit. 0 if unsupported.
- * @width:	Mux field width. 0 if unsupported.
- *
- * A representation of a group of signals (possibly just one signal) in the
- * TZ1090 which can be muxed to a set of functions or sub muxes.
- */
-struct tz1090_muxdesc {
-	int	funcs[5];
-	u16	reg;
-	u8	bit;
-	u8	width;
-};
-
-/**
- * struct tz1090_pingroup - TZ1090 pin group
- * @name:	Name of pin group.
- * @pins:	Array of pin numbers in this pin group.
- * @npins:	Number of pins in this pin group.
- * @mux:	Top level mux.
- * @drv:	Drive control supported, 0 if unsupported.
- *		This means Schmitt, Slew, and Drive strength.
- * @slw_bit:	Slew register bit. 0 if unsupported.
- *		The same bit is used for Schmitt, and Drive (*2).
- * @func:	Currently muxed function.
- * @func_count:	Number of pins using current mux function.
- *
- * A representation of a group of pins (possibly just one pin) in the TZ1090
- * pin controller. Each group allows some parameter or parameters to be
- * configured. The most common is mux function selection.
- */
-struct tz1090_pingroup {
-	const char		*name;
-	const unsigned int	*pins;
-	unsigned int		npins;
-	struct tz1090_muxdesc	mux;
-
-	bool			drv;
-	u8			slw_bit;
-
-	int			func;
-	unsigned int		func_count;
-};
-
-/*
- * Most pins affected by the pinmux can also be GPIOs. Define these first.
- * These must match how the GPIO driver names/numbers its pins.
- */
-
-enum tz1090_pin {
-	/* GPIO pins */
-	TZ1090_PIN_SDIO_CLK,
-	TZ1090_PIN_SDIO_CMD,
-	TZ1090_PIN_SDIO_D0,
-	TZ1090_PIN_SDIO_D1,
-	TZ1090_PIN_SDIO_D2,
-	TZ1090_PIN_SDIO_D3,
-	TZ1090_PIN_SDH_CD,
-	TZ1090_PIN_SDH_WP,
-	TZ1090_PIN_SPI0_MCLK,
-	TZ1090_PIN_SPI0_CS0,
-	TZ1090_PIN_SPI0_CS1,
-	TZ1090_PIN_SPI0_CS2,
-	TZ1090_PIN_SPI0_DOUT,
-	TZ1090_PIN_SPI0_DIN,
-	TZ1090_PIN_SPI1_MCLK,
-	TZ1090_PIN_SPI1_CS0,
-	TZ1090_PIN_SPI1_CS1,
-	TZ1090_PIN_SPI1_CS2,
-	TZ1090_PIN_SPI1_DOUT,
-	TZ1090_PIN_SPI1_DIN,
-	TZ1090_PIN_UART0_RXD,
-	TZ1090_PIN_UART0_TXD,
-	TZ1090_PIN_UART0_CTS,
-	TZ1090_PIN_UART0_RTS,
-	TZ1090_PIN_UART1_RXD,
-	TZ1090_PIN_UART1_TXD,
-	TZ1090_PIN_SCB0_SDAT,
-	TZ1090_PIN_SCB0_SCLK,
-	TZ1090_PIN_SCB1_SDAT,
-	TZ1090_PIN_SCB1_SCLK,
-	TZ1090_PIN_SCB2_SDAT,
-	TZ1090_PIN_SCB2_SCLK,
-	TZ1090_PIN_I2S_MCLK,
-	TZ1090_PIN_I2S_BCLK_OUT,
-	TZ1090_PIN_I2S_LRCLK_OUT,
-	TZ1090_PIN_I2S_DOUT0,
-	TZ1090_PIN_I2S_DOUT1,
-	TZ1090_PIN_I2S_DOUT2,
-	TZ1090_PIN_I2S_DIN,
-	TZ1090_PIN_PDM_A,
-	TZ1090_PIN_PDM_B,
-	TZ1090_PIN_PDM_C,
-	TZ1090_PIN_PDM_D,
-	TZ1090_PIN_TFT_RED0,
-	TZ1090_PIN_TFT_RED1,
-	TZ1090_PIN_TFT_RED2,
-	TZ1090_PIN_TFT_RED3,
-	TZ1090_PIN_TFT_RED4,
-	TZ1090_PIN_TFT_RED5,
-	TZ1090_PIN_TFT_RED6,
-	TZ1090_PIN_TFT_RED7,
-	TZ1090_PIN_TFT_GREEN0,
-	TZ1090_PIN_TFT_GREEN1,
-	TZ1090_PIN_TFT_GREEN2,
-	TZ1090_PIN_TFT_GREEN3,
-	TZ1090_PIN_TFT_GREEN4,
-	TZ1090_PIN_TFT_GREEN5,
-	TZ1090_PIN_TFT_GREEN6,
-	TZ1090_PIN_TFT_GREEN7,
-	TZ1090_PIN_TFT_BLUE0,
-	TZ1090_PIN_TFT_BLUE1,
-	TZ1090_PIN_TFT_BLUE2,
-	TZ1090_PIN_TFT_BLUE3,
-	TZ1090_PIN_TFT_BLUE4,
-	TZ1090_PIN_TFT_BLUE5,
-	TZ1090_PIN_TFT_BLUE6,
-	TZ1090_PIN_TFT_BLUE7,
-	TZ1090_PIN_TFT_VDDEN_GD,
-	TZ1090_PIN_TFT_PANELCLK,
-	TZ1090_PIN_TFT_BLANK_LS,
-	TZ1090_PIN_TFT_VSYNC_NS,
-	TZ1090_PIN_TFT_HSYNC_NR,
-	TZ1090_PIN_TFT_VD12ACB,
-	TZ1090_PIN_TFT_PWRSAVE,
-	TZ1090_PIN_TX_ON,
-	TZ1090_PIN_RX_ON,
-	TZ1090_PIN_PLL_ON,
-	TZ1090_PIN_PA_ON,
-	TZ1090_PIN_RX_HP,
-	TZ1090_PIN_GAIN0,
-	TZ1090_PIN_GAIN1,
-	TZ1090_PIN_GAIN2,
-	TZ1090_PIN_GAIN3,
-	TZ1090_PIN_GAIN4,
-	TZ1090_PIN_GAIN5,
-	TZ1090_PIN_GAIN6,
-	TZ1090_PIN_GAIN7,
-	TZ1090_PIN_ANT_SEL0,
-	TZ1090_PIN_ANT_SEL1,
-	TZ1090_PIN_SDH_CLK_IN,
-
-	/* Non-GPIO pins */
-	TZ1090_PIN_TCK,
-	TZ1090_PIN_TRST,
-	TZ1090_PIN_TDI,
-	TZ1090_PIN_TDO,
-	TZ1090_PIN_TMS,
-	TZ1090_PIN_CLK_OUT0,
-	TZ1090_PIN_CLK_OUT1,
-
-	NUM_GPIOS = TZ1090_PIN_TCK,
-};
-
-/* Pin names */
-
-static const struct pinctrl_pin_desc tz1090_pins[] = {
-	/* GPIO pins */
-	PINCTRL_PIN(TZ1090_PIN_SDIO_CLK,	"sdio_clk"),
-	PINCTRL_PIN(TZ1090_PIN_SDIO_CMD,	"sdio_cmd"),
-	PINCTRL_PIN(TZ1090_PIN_SDIO_D0,		"sdio_d0"),
-	PINCTRL_PIN(TZ1090_PIN_SDIO_D1,		"sdio_d1"),
-	PINCTRL_PIN(TZ1090_PIN_SDIO_D2,		"sdio_d2"),
-	PINCTRL_PIN(TZ1090_PIN_SDIO_D3,		"sdio_d3"),
-	PINCTRL_PIN(TZ1090_PIN_SDH_CD,		"sdh_cd"),
-	PINCTRL_PIN(TZ1090_PIN_SDH_WP,		"sdh_wp"),
-	PINCTRL_PIN(TZ1090_PIN_SPI0_MCLK,	"spi0_mclk"),
-	PINCTRL_PIN(TZ1090_PIN_SPI0_CS0,	"spi0_cs0"),
-	PINCTRL_PIN(TZ1090_PIN_SPI0_CS1,	"spi0_cs1"),
-	PINCTRL_PIN(TZ1090_PIN_SPI0_CS2,	"spi0_cs2"),
-	PINCTRL_PIN(TZ1090_PIN_SPI0_DOUT,	"spi0_dout"),
-	PINCTRL_PIN(TZ1090_PIN_SPI0_DIN,	"spi0_din"),
-	PINCTRL_PIN(TZ1090_PIN_SPI1_MCLK,	"spi1_mclk"),
-	PINCTRL_PIN(TZ1090_PIN_SPI1_CS0,	"spi1_cs0"),
-	PINCTRL_PIN(TZ1090_PIN_SPI1_CS1,	"spi1_cs1"),
-	PINCTRL_PIN(TZ1090_PIN_SPI1_CS2,	"spi1_cs2"),
-	PINCTRL_PIN(TZ1090_PIN_SPI1_DOUT,	"spi1_dout"),
-	PINCTRL_PIN(TZ1090_PIN_SPI1_DIN,	"spi1_din"),
-	PINCTRL_PIN(TZ1090_PIN_UART0_RXD,	"uart0_rxd"),
-	PINCTRL_PIN(TZ1090_PIN_UART0_TXD,	"uart0_txd"),
-	PINCTRL_PIN(TZ1090_PIN_UART0_CTS,	"uart0_cts"),
-	PINCTRL_PIN(TZ1090_PIN_UART0_RTS,	"uart0_rts"),
-	PINCTRL_PIN(TZ1090_PIN_UART1_RXD,	"uart1_rxd"),
-	PINCTRL_PIN(TZ1090_PIN_UART1_TXD,	"uart1_txd"),
-	PINCTRL_PIN(TZ1090_PIN_SCB0_SDAT,	"scb0_sdat"),
-	PINCTRL_PIN(TZ1090_PIN_SCB0_SCLK,	"scb0_sclk"),
-	PINCTRL_PIN(TZ1090_PIN_SCB1_SDAT,	"scb1_sdat"),
-	PINCTRL_PIN(TZ1090_PIN_SCB1_SCLK,	"scb1_sclk"),
-	PINCTRL_PIN(TZ1090_PIN_SCB2_SDAT,	"scb2_sdat"),
-	PINCTRL_PIN(TZ1090_PIN_SCB2_SCLK,	"scb2_sclk"),
-	PINCTRL_PIN(TZ1090_PIN_I2S_MCLK,	"i2s_mclk"),
-	PINCTRL_PIN(TZ1090_PIN_I2S_BCLK_OUT,	"i2s_bclk_out"),
-	PINCTRL_PIN(TZ1090_PIN_I2S_LRCLK_OUT,	"i2s_lrclk_out"),
-	PINCTRL_PIN(TZ1090_PIN_I2S_DOUT0,	"i2s_dout0"),
-	PINCTRL_PIN(TZ1090_PIN_I2S_DOUT1,	"i2s_dout1"),
-	PINCTRL_PIN(TZ1090_PIN_I2S_DOUT2,	"i2s_dout2"),
-	PINCTRL_PIN(TZ1090_PIN_I2S_DIN,		"i2s_din"),
-	PINCTRL_PIN(TZ1090_PIN_PDM_A,		"pdm_a"),
-	PINCTRL_PIN(TZ1090_PIN_PDM_B,		"pdm_b"),
-	PINCTRL_PIN(TZ1090_PIN_PDM_C,		"pdm_c"),
-	PINCTRL_PIN(TZ1090_PIN_PDM_D,		"pdm_d"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_RED0,	"tft_red0"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_RED1,	"tft_red1"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_RED2,	"tft_red2"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_RED3,	"tft_red3"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_RED4,	"tft_red4"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_RED5,	"tft_red5"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_RED6,	"tft_red6"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_RED7,	"tft_red7"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_GREEN0,	"tft_green0"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_GREEN1,	"tft_green1"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_GREEN2,	"tft_green2"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_GREEN3,	"tft_green3"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_GREEN4,	"tft_green4"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_GREEN5,	"tft_green5"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_GREEN6,	"tft_green6"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_GREEN7,	"tft_green7"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_BLUE0,	"tft_blue0"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_BLUE1,	"tft_blue1"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_BLUE2,	"tft_blue2"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_BLUE3,	"tft_blue3"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_BLUE4,	"tft_blue4"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_BLUE5,	"tft_blue5"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_BLUE6,	"tft_blue6"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_BLUE7,	"tft_blue7"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_VDDEN_GD,	"tft_vdden_gd"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_PANELCLK,	"tft_panelclk"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_BLANK_LS,	"tft_blank_ls"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_VSYNC_NS,	"tft_vsync_ns"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_HSYNC_NR,	"tft_hsync_nr"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_VD12ACB,	"tft_vd12acb"),
-	PINCTRL_PIN(TZ1090_PIN_TFT_PWRSAVE,	"tft_pwrsave"),
-	PINCTRL_PIN(TZ1090_PIN_TX_ON,		"tx_on"),
-	PINCTRL_PIN(TZ1090_PIN_RX_ON,		"rx_on"),
-	PINCTRL_PIN(TZ1090_PIN_PLL_ON,		"pll_on"),
-	PINCTRL_PIN(TZ1090_PIN_PA_ON,		"pa_on"),
-	PINCTRL_PIN(TZ1090_PIN_RX_HP,		"rx_hp"),
-	PINCTRL_PIN(TZ1090_PIN_GAIN0,		"gain0"),
-	PINCTRL_PIN(TZ1090_PIN_GAIN1,		"gain1"),
-	PINCTRL_PIN(TZ1090_PIN_GAIN2,		"gain2"),
-	PINCTRL_PIN(TZ1090_PIN_GAIN3,		"gain3"),
-	PINCTRL_PIN(TZ1090_PIN_GAIN4,		"gain4"),
-	PINCTRL_PIN(TZ1090_PIN_GAIN5,		"gain5"),
-	PINCTRL_PIN(TZ1090_PIN_GAIN6,		"gain6"),
-	PINCTRL_PIN(TZ1090_PIN_GAIN7,		"gain7"),
-	PINCTRL_PIN(TZ1090_PIN_ANT_SEL0,	"ant_sel0"),
-	PINCTRL_PIN(TZ1090_PIN_ANT_SEL1,	"ant_sel1"),
-	PINCTRL_PIN(TZ1090_PIN_SDH_CLK_IN,	"sdh_clk_in"),
-
-	/* Non-GPIO pins */
-	PINCTRL_PIN(TZ1090_PIN_TCK,		"tck"),
-	PINCTRL_PIN(TZ1090_PIN_TRST,		"trst"),
-	PINCTRL_PIN(TZ1090_PIN_TDI,		"tdi"),
-	PINCTRL_PIN(TZ1090_PIN_TDO,		"tdo"),
-	PINCTRL_PIN(TZ1090_PIN_TMS,		"tms"),
-	PINCTRL_PIN(TZ1090_PIN_CLK_OUT0,	"clk_out0"),
-	PINCTRL_PIN(TZ1090_PIN_CLK_OUT1,	"clk_out1"),
-};
-
-/* Pins in each pin group */
-
-static const unsigned int spi1_cs2_pins[] = {
-	TZ1090_PIN_SPI1_CS2,
-};
-
-static const unsigned int pdm_d_pins[] = {
-	TZ1090_PIN_PDM_D,
-};
-
-static const unsigned int tft_pins[] = {
-	TZ1090_PIN_TFT_RED0,
-	TZ1090_PIN_TFT_RED1,
-	TZ1090_PIN_TFT_RED2,
-	TZ1090_PIN_TFT_RED3,
-	TZ1090_PIN_TFT_RED4,
-	TZ1090_PIN_TFT_RED5,
-	TZ1090_PIN_TFT_RED6,
-	TZ1090_PIN_TFT_RED7,
-	TZ1090_PIN_TFT_GREEN0,
-	TZ1090_PIN_TFT_GREEN1,
-	TZ1090_PIN_TFT_GREEN2,
-	TZ1090_PIN_TFT_GREEN3,
-	TZ1090_PIN_TFT_GREEN4,
-	TZ1090_PIN_TFT_GREEN5,
-	TZ1090_PIN_TFT_GREEN6,
-	TZ1090_PIN_TFT_GREEN7,
-	TZ1090_PIN_TFT_BLUE0,
-	TZ1090_PIN_TFT_BLUE1,
-	TZ1090_PIN_TFT_BLUE2,
-	TZ1090_PIN_TFT_BLUE3,
-	TZ1090_PIN_TFT_BLUE4,
-	TZ1090_PIN_TFT_BLUE5,
-	TZ1090_PIN_TFT_BLUE6,
-	TZ1090_PIN_TFT_BLUE7,
-	TZ1090_PIN_TFT_VDDEN_GD,
-	TZ1090_PIN_TFT_PANELCLK,
-	TZ1090_PIN_TFT_BLANK_LS,
-	TZ1090_PIN_TFT_VSYNC_NS,
-	TZ1090_PIN_TFT_HSYNC_NR,
-	TZ1090_PIN_TFT_VD12ACB,
-	TZ1090_PIN_TFT_PWRSAVE,
-};
-
-static const unsigned int afe_pins[] = {
-	TZ1090_PIN_TX_ON,
-	TZ1090_PIN_RX_ON,
-	TZ1090_PIN_PLL_ON,
-	TZ1090_PIN_PA_ON,
-	TZ1090_PIN_RX_HP,
-	TZ1090_PIN_ANT_SEL0,
-	TZ1090_PIN_ANT_SEL1,
-	TZ1090_PIN_GAIN0,
-	TZ1090_PIN_GAIN1,
-	TZ1090_PIN_GAIN2,
-	TZ1090_PIN_GAIN3,
-	TZ1090_PIN_GAIN4,
-	TZ1090_PIN_GAIN5,
-	TZ1090_PIN_GAIN6,
-	TZ1090_PIN_GAIN7,
-};
-
-static const unsigned int sdio_pins[] = {
-	TZ1090_PIN_SDIO_CLK,
-	TZ1090_PIN_SDIO_CMD,
-	TZ1090_PIN_SDIO_D0,
-	TZ1090_PIN_SDIO_D1,
-	TZ1090_PIN_SDIO_D2,
-	TZ1090_PIN_SDIO_D3,
-};
-
-static const unsigned int sdh_pins[] = {
-	TZ1090_PIN_SDH_CD,
-	TZ1090_PIN_SDH_WP,
-	TZ1090_PIN_SDH_CLK_IN,
-};
-
-static const unsigned int spi0_pins[] = {
-	TZ1090_PIN_SPI0_MCLK,
-	TZ1090_PIN_SPI0_CS0,
-	TZ1090_PIN_SPI0_CS1,
-	TZ1090_PIN_SPI0_CS2,
-	TZ1090_PIN_SPI0_DOUT,
-	TZ1090_PIN_SPI0_DIN,
-};
-
-static const unsigned int spi1_pins[] = {
-	TZ1090_PIN_SPI1_MCLK,
-	TZ1090_PIN_SPI1_CS0,
-	TZ1090_PIN_SPI1_CS1,
-	TZ1090_PIN_SPI1_CS2,
-	TZ1090_PIN_SPI1_DOUT,
-	TZ1090_PIN_SPI1_DIN,
-};
-
-static const unsigned int uart0_pins[] = {
-	TZ1090_PIN_UART0_RTS,
-	TZ1090_PIN_UART0_CTS,
-	TZ1090_PIN_UART0_TXD,
-	TZ1090_PIN_UART0_RXD,
-};
-
-static const unsigned int uart1_pins[] = {
-	TZ1090_PIN_UART1_TXD,
-	TZ1090_PIN_UART1_RXD,
-};
-
-static const unsigned int uart_pins[] = {
-	TZ1090_PIN_UART1_TXD,
-	TZ1090_PIN_UART1_RXD,
-	TZ1090_PIN_UART0_RTS,
-	TZ1090_PIN_UART0_CTS,
-	TZ1090_PIN_UART0_TXD,
-	TZ1090_PIN_UART0_RXD,
-};
-
-static const unsigned int scb0_pins[] = {
-	TZ1090_PIN_SCB0_SDAT,
-	TZ1090_PIN_SCB0_SCLK,
-};
-
-static const unsigned int scb1_pins[] = {
-	TZ1090_PIN_SCB1_SDAT,
-	TZ1090_PIN_SCB1_SCLK,
-};
-
-static const unsigned int scb2_pins[] = {
-	TZ1090_PIN_SCB2_SDAT,
-	TZ1090_PIN_SCB2_SCLK,
-};
-
-static const unsigned int i2s_pins[] = {
-	TZ1090_PIN_I2S_MCLK,
-	TZ1090_PIN_I2S_BCLK_OUT,
-	TZ1090_PIN_I2S_LRCLK_OUT,
-	TZ1090_PIN_I2S_DOUT0,
-	TZ1090_PIN_I2S_DOUT1,
-	TZ1090_PIN_I2S_DOUT2,
-	TZ1090_PIN_I2S_DIN,
-};
-
-static const unsigned int jtag_pins[] = {
-	TZ1090_PIN_TCK,
-	TZ1090_PIN_TRST,
-	TZ1090_PIN_TDI,
-	TZ1090_PIN_TDO,
-	TZ1090_PIN_TMS,
-};
-
-/* Pins in each drive pin group */
-
-static const unsigned int drive_sdio_pins[] = {
-	TZ1090_PIN_SDIO_CLK,
-	TZ1090_PIN_SDIO_CMD,
-	TZ1090_PIN_SDIO_D0,
-	TZ1090_PIN_SDIO_D1,
-	TZ1090_PIN_SDIO_D2,
-	TZ1090_PIN_SDIO_D3,
-	TZ1090_PIN_SDH_WP,
-	TZ1090_PIN_SDH_CD,
-	TZ1090_PIN_SDH_CLK_IN,
-};
-
-static const unsigned int drive_i2s_pins[] = {
-	TZ1090_PIN_CLK_OUT1,
-	TZ1090_PIN_I2S_DIN,
-	TZ1090_PIN_I2S_DOUT0,
-	TZ1090_PIN_I2S_DOUT1,
-	TZ1090_PIN_I2S_DOUT2,
-	TZ1090_PIN_I2S_LRCLK_OUT,
-	TZ1090_PIN_I2S_BCLK_OUT,
-	TZ1090_PIN_I2S_MCLK,
-};
-
-static const unsigned int drive_scb0_pins[] = {
-	TZ1090_PIN_SCB0_SCLK,
-	TZ1090_PIN_SCB0_SDAT,
-	TZ1090_PIN_PDM_D,
-	TZ1090_PIN_PDM_C,
-};
-
-static const unsigned int drive_pdm_pins[] = {
-	TZ1090_PIN_CLK_OUT0,
-	TZ1090_PIN_PDM_B,
-	TZ1090_PIN_PDM_A,
-};
-
-/* Pin groups each function can be muxed to */
-
-/*
- * The magic "perip" function allows otherwise non-muxing pins to be enabled in
- * peripheral mode.
- */
-static const char * const perip_groups[] = {
-	/* non-muxing convenient gpio pingroups */
-	"uart",
-	"uart0",
-	"uart1",
-	"spi0",
-	"spi1",
-	"scb0",
-	"scb1",
-	"scb2",
-	"i2s",
-	/* individual pins not part of a pin mux group */
-	"spi0_mclk",
-	"spi0_cs0",
-	"spi0_cs1",
-	"spi0_cs2",
-	"spi0_dout",
-	"spi0_din",
-	"spi1_mclk",
-	"spi1_cs0",
-	"spi1_cs1",
-	"spi1_dout",
-	"spi1_din",
-	"uart0_rxd",
-	"uart0_txd",
-	"uart0_cts",
-	"uart0_rts",
-	"uart1_rxd",
-	"uart1_txd",
-	"scb0_sdat",
-	"scb0_sclk",
-	"scb1_sdat",
-	"scb1_sclk",
-	"scb2_sdat",
-	"scb2_sclk",
-	"i2s_mclk",
-	"i2s_bclk_out",
-	"i2s_lrclk_out",
-	"i2s_dout0",
-	"i2s_dout1",
-	"i2s_dout2",
-	"i2s_din",
-	"pdm_a",
-	"pdm_b",
-	"pdm_c",
-};
-
-static const char * const sdh_sdio_groups[] = {
-	"sdh",
-	"sdio",
-	/* sdh pins */
-	"sdh_cd",
-	"sdh_wp",
-	"sdh_clk_in",
-	/* sdio pins */
-	"sdio_clk",
-	"sdio_cmd",
-	"sdio_d0",
-	"sdio_d1",
-	"sdio_d2",
-	"sdio_d3",
-};
-
-static const char * const spi1_cs2_groups[] = {
-	"spi1_cs2",
-};
-
-static const char * const pdm_dac_groups[] = {
-	"pdm_d",
-};
-
-static const char * const usb_vbus_groups[] = {
-	"spi1_cs2",
-	"pdm_d",
-};
-
-static const char * const afe_groups[] = {
-	"afe",
-	/* afe pins */
-	"tx_on",
-	"rx_on",
-	"pll_on",
-	"pa_on",
-	"rx_hp",
-	"ant_sel0",
-	"ant_sel1",
-	"gain0",
-	"gain1",
-	"gain2",
-	"gain3",
-	"gain4",
-	"gain5",
-	"gain6",
-	"gain7",
-};
-
-static const char * const tft_groups[] = {
-	"tft",
-	/* tft pins */
-	"tft_red0",
-	"tft_red1",
-	"tft_red2",
-	"tft_red3",
-	"tft_red4",
-	"tft_red5",
-	"tft_red6",
-	"tft_red7",
-	"tft_green0",
-	"tft_green1",
-	"tft_green2",
-	"tft_green3",
-	"tft_green4",
-	"tft_green5",
-	"tft_green6",
-	"tft_green7",
-	"tft_blue0",
-	"tft_blue1",
-	"tft_blue2",
-	"tft_blue3",
-	"tft_blue4",
-	"tft_blue5",
-	"tft_blue6",
-	"tft_blue7",
-	"tft_vdden_gd",
-	"tft_panelclk",
-	"tft_blank_ls",
-	"tft_vsync_ns",
-	"tft_hsync_nr",
-	"tft_vd12acb",
-	"tft_pwrsave",
-};
-
-/* Mux functions that can be used by a mux */
-
-enum tz1090_mux {
-	/* internal placeholder */
-	TZ1090_MUX_NA = -1,
-	/* magic per-non-muxing-GPIO-pin peripheral mode mux */
-	TZ1090_MUX_PERIP,
-	/* SDH/SDIO mux */
-	TZ1090_MUX_SDH,
-	TZ1090_MUX_SDIO,
-	/* USB_VBUS muxes */
-	TZ1090_MUX_SPI1_CS2,
-	TZ1090_MUX_PDM_DAC,
-	TZ1090_MUX_USB_VBUS,
-	/* AFE mux */
-	TZ1090_MUX_AFE,
-	TZ1090_MUX_TS_OUT_0,
-	/* EXT_DAC mux */
-	TZ1090_MUX_DAC,
-	TZ1090_MUX_NOT_IQADC_STB,
-	TZ1090_MUX_IQDAC_STB,
-	/* TFT mux */
-	TZ1090_MUX_TFT,
-	TZ1090_MUX_EXT_DAC,
-	TZ1090_MUX_TS_OUT_1,
-	TZ1090_MUX_LCD_TRACE,
-	TZ1090_MUX_PHY_RINGOSC,
-};
-
-#define FUNCTION(mux, fname, group)			\
-	[(TZ1090_MUX_ ## mux)] = {			\
-		.name = #fname,				\
-		.groups = group##_groups,		\
-		.ngroups = ARRAY_SIZE(group##_groups),	\
-	}
-/* For intermediate functions with submuxes */
-#define NULL_FUNCTION(mux, fname)			\
-	[(TZ1090_MUX_ ## mux)] = {			\
-		.name = #fname,				\
-	}
-
-/* Must correlate with enum tz1090_mux */
-static const struct tz1090_function tz1090_functions[] = {
-	/*	 FUNCTION	function name	pingroups */
-	FUNCTION(PERIP,		perip,		perip),
-	FUNCTION(SDH,		sdh,		sdh_sdio),
-	FUNCTION(SDIO,		sdio,		sdh_sdio),
-	FUNCTION(SPI1_CS2,	spi1_cs2,	spi1_cs2),
-	FUNCTION(PDM_DAC,	pdm_dac,	pdm_dac),
-	FUNCTION(USB_VBUS,	usb_vbus,	usb_vbus),
-	FUNCTION(AFE,		afe,		afe),
-	FUNCTION(TS_OUT_0,	ts_out_0,	afe),
-	FUNCTION(DAC,		ext_dac,	tft),
-	FUNCTION(NOT_IQADC_STB,	not_iqadc_stb,	tft),
-	FUNCTION(IQDAC_STB,	iqdac_stb,	tft),
-	FUNCTION(TFT,		tft,		tft),
-	NULL_FUNCTION(EXT_DAC,	_ext_dac),
-	FUNCTION(TS_OUT_1,	ts_out_1,	tft),
-	FUNCTION(LCD_TRACE,	lcd_trace,	tft),
-	FUNCTION(PHY_RINGOSC,	phy_ringosc,	tft),
-};
-
-/* Sub muxes */
-
-/**
- * MUX() - Initialise a mux description.
- * @f0:		Function 0 (TZ1090_MUX_ is prepended, NA for none)
- * @f1:		Function 1 (TZ1090_MUX_ is prepended, NA for none)
- * @f2:		Function 2 (TZ1090_MUX_ is prepended, NA for none)
- * @f3:		Function 3 (TZ1090_MUX_ is prepended, NA for none)
- * @f4:		Function 4 (TZ1090_MUX_ is prepended, NA for none)
- * @mux_r:	Mux register (REG_PINCTRL_ is prepended)
- * @mux_b:	Bit number in register that the mux field begins
- * @mux_w:	Width of mux field in register
- */
-#define MUX(f0, f1, f2, f3, f4, mux_r, mux_b, mux_w)		\
-	{							\
-		.funcs = {					\
-			TZ1090_MUX_ ## f0,			\
-			TZ1090_MUX_ ## f1,			\
-			TZ1090_MUX_ ## f2,			\
-			TZ1090_MUX_ ## f3,			\
-			TZ1090_MUX_ ## f4,			\
-		},						\
-		.reg = (REG_PINCTRL_ ## mux_r),			\
-		.bit = (mux_b),					\
-		.width = (mux_w),				\
-	}
-
-/**
- * DEFINE_SUBMUX() - Defines a submux description separate from a pin group.
- * @mux:	Mux name (_submux is appended)
- * @f0:		Function 0 (TZ1090_MUX_ is prepended, NA for none)
- * @f1:		Function 1 (TZ1090_MUX_ is prepended, NA for none)
- * @f2:		Function 2 (TZ1090_MUX_ is prepended, NA for none)
- * @f3:		Function 3 (TZ1090_MUX_ is prepended, NA for none)
- * @f4:		Function 4 (TZ1090_MUX_ is prepended, NA for none)
- * @mux_r:	Mux register (REG_PINCTRL_ is prepended)
- * @mux_b:	Bit number in register that the mux field begins
- * @mux_w:	Width of mux field in register
- *
- * A sub mux is a nested mux that can be bound to a magic function number used
- * by another mux description. For example value 4 of the top level mux might
- * correspond to a function which has a submux pointed to in tz1090_submux[].
- * The outer mux can then take on any function in the top level mux or the
- * submux, and if a submux function is chosen both muxes are updated to route
- * the signal from the submux.
- *
- * The submux can be defined with DEFINE_SUBMUX and pointed to from
- * tz1090_submux[] using SUBMUX.
- */
-#define DEFINE_SUBMUX(mux, f0, f1, f2, f3, f4, mux_r, mux_b, mux_w)	\
-	static struct tz1090_muxdesc mux ## _submux =			\
-		MUX(f0, f1, f2, f3, f4, mux_r, mux_b, mux_w)
-
-/**
- * SUBMUX() - Link a submux to a function number.
- * @f:		Function name (TZ1090_MUX_ is prepended)
- * @submux:	Submux name (_submux is appended)
- *
- * For use in tz1090_submux[] initialisation to link an intermediate function
- * number to a particular submux description. It indicates that when the
- * function is chosen the signal is connected to the submux.
- */
-#define SUBMUX(f, submux)	[(TZ1090_MUX_ ## f)] = &(submux ## _submux)
-
-/**
- * MUX_PG() - Initialise a pin group with mux control
- * @pg_name:	Pin group name (stringified, _pins appended to get pins array)
- * @f0:		Function 0 (TZ1090_MUX_ is prepended, NA for none)
- * @f1:		Function 1 (TZ1090_MUX_ is prepended, NA for none)
- * @f2:		Function 2 (TZ1090_MUX_ is prepended, NA for none)
- * @f3:		Function 3 (TZ1090_MUX_ is prepended, NA for none)
- * @f4:		Function 4 (TZ1090_MUX_ is prepended, NA for none)
- * @mux_r:	Mux register (REG_PINCTRL_ is prepended)
- * @mux_b:	Bit number in register that the mux field begins
- * @mux_w:	Width of mux field in register
- */
-#define MUX_PG(pg_name, f0, f1, f2, f3, f4,			\
-	       mux_r, mux_b, mux_w)				\
-	{							\
-		.name = #pg_name,				\
-		.pins = pg_name##_pins,				\
-		.npins = ARRAY_SIZE(pg_name##_pins),		\
-		.mux = MUX(f0, f1, f2, f3, f4,			\
-			   mux_r, mux_b, mux_w),		\
-	}
-
-/**
- * SIMPLE_PG() - Initialise a simple convenience pin group
- * @pg_name:	Pin group name (stringified, _pins appended to get pins array)
- *
- * A simple pin group is simply used for binding pins together so they can be
- * referred to by a single name instead of having to list every pin
- * individually.
- */
-#define SIMPLE_PG(pg_name)					\
-	{							\
-		.name = #pg_name,				\
-		.pins = pg_name##_pins,				\
-		.npins = ARRAY_SIZE(pg_name##_pins),		\
-	}
-
-/**
- * DRV_PG() - Initialise a pin group with drive control
- * @pg_name:	Pin group name (stringified, _pins appended to get pins array)
- * @slw_b:	Slew register bit.
- *		The same bit is used for Schmitt, and Drive (*2).
- */
-#define DRV_PG(pg_name, slw_b)					\
-	{							\
-		.name = #pg_name,				\
-		.pins = pg_name##_pins,				\
-		.npins = ARRAY_SIZE(pg_name##_pins),		\
-		.drv = true,					\
-		.slw_bit = (slw_b),				\
-	}
-
-/*
- * Define main muxing pin groups
- */
-
-/* submuxes */
-
-/*            name     f0,  f1,            f2,        f3, f4, mux r/b/w */
-DEFINE_SUBMUX(ext_dac, DAC, NOT_IQADC_STB, IQDAC_STB, NA, NA, IF_CTL, 6, 2);
-
-/* bind submuxes to internal functions */
-static struct tz1090_muxdesc *tz1090_submux[] = {
-	SUBMUX(EXT_DAC, ext_dac),
-};
-
-/*
- * These are the pin mux groups. Pin muxing can be enabled and disabled for each
- * pin individually so these groups are internal. The mapping of pins to pin mux
- * group is below (tz1090_mux_pins).
- */
-static struct tz1090_pingroup tz1090_mux_groups[] = {
-	/* Muxing pin groups */
-	/*     pg_name,  f0,       f1,       f2,       f3,        f4,          mux r/b/w */
-	MUX_PG(sdh,      SDH,      SDIO,     NA,       NA,        NA,          IF_CTL, 20, 2),
-	MUX_PG(sdio,     SDIO,     SDH,      NA,       NA,        NA,          IF_CTL, 16, 2),
-	MUX_PG(spi1_cs2, SPI1_CS2, USB_VBUS, NA,       NA,        NA,          IF_CTL, 10, 2),
-	MUX_PG(pdm_d,    PDM_DAC,  USB_VBUS, NA,       NA,        NA,          IF_CTL,  8, 2),
-	MUX_PG(afe,      AFE,      TS_OUT_0, NA,       NA,        NA,          IF_CTL,  4, 2),
-	MUX_PG(tft,      TFT,      EXT_DAC,  TS_OUT_1, LCD_TRACE, PHY_RINGOSC, IF_CTL,  0, 3),
-};
-
-/*
- * This is the mapping from GPIO pins to pin mux groups in tz1090_mux_groups[].
- * Pins which aren't muxable to multiple peripherals are set to
- * TZ1090_MUX_GROUP_MAX to enable the "perip" function to enable/disable
- * peripheral control of the pin.
- *
- * This array is initialised in tz1090_init_mux_pins().
- */
-static u8 tz1090_mux_pins[NUM_GPIOS];
-
-/* TZ1090_MUX_GROUP_MAX is used in tz1090_mux_pins[] for non-muxing pins */
-#define TZ1090_MUX_GROUP_MAX ARRAY_SIZE(tz1090_mux_groups)
-
-/**
- * tz1090_init_mux_pins() - Initialise GPIO pin to mux group mapping.
- *
- * Initialises the tz1090_mux_pins[] array to be the inverse of the pin lists in
- * each pin mux group in tz1090_mux_groups[].
- *
- * It is assumed that no pin mux groups overlap (share pins).
- */
-static void __init tz1090_init_mux_pins(void)
-{
-	unsigned int g, p;
-	const struct tz1090_pingroup *grp;
-	const unsigned int *pin;
-
-	for (p = 0; p < NUM_GPIOS; ++p)
-		tz1090_mux_pins[p] = TZ1090_MUX_GROUP_MAX;
-
-	grp = tz1090_mux_groups;
-	for (g = 0, grp = tz1090_mux_groups;
-	     g < ARRAY_SIZE(tz1090_mux_groups); ++g, ++grp)
-		for (pin = grp->pins, p = 0; p < grp->npins; ++p, ++pin)
-			tz1090_mux_pins[*pin] = g;
-}
-
-/*
- * These are the externally visible pin groups. Some of them allow group control
- * of drive configuration. Some are just simple convenience pingroups. All the
- * internal pin mux groups in tz1090_mux_groups[] are mirrored here with the
- * same pins.
- * Pseudo pin groups follow in the group numbers after this array for each GPIO
- * pin. Any group used for muxing must have all pins belonging to the same pin
- * mux group.
- */
-static struct tz1090_pingroup tz1090_groups[] = {
-	/* Pin groups with drive control (with no out of place pins) */
-	/*     pg_name,		slw/schmitt/drv b */
-	DRV_PG(jtag,		11 /* 11, 22 */),
-	DRV_PG(tft,		10 /* 10, 20 */),
-	DRV_PG(scb2,		9  /*  9, 18 */),
-	DRV_PG(spi0,		7  /*  7, 14 */),
-	DRV_PG(uart,		5  /*  5, 10 */),
-	DRV_PG(scb1,		4  /*  4,  8 */),
-	DRV_PG(spi1,		3  /*  3,  6 */),
-	DRV_PG(afe,		0  /*  0,  0 */),
-
-	/*
-	 * Drive specific pin groups (with odd combinations of pins which makes
-	 * the pin group naming somewhat arbitrary)
-	 */
-	/*     pg_name,		slw/schmitt/drv b */
-	DRV_PG(drive_sdio,	8  /*  8, 16 */), /* sdio_* + sdh_* */
-	DRV_PG(drive_i2s,	6  /*  6, 12 */), /* i2s_* + clk_out1 */
-	DRV_PG(drive_scb0,	2  /*  2,  4 */), /* scb0_* + pdm_{c,d} */
-	DRV_PG(drive_pdm,	1  /*  1,  2 */), /* pdm_{a,b} + clk_out0 */
-
-	/* Convenience pin groups */
-	/*        pg_name */
-	SIMPLE_PG(uart0),
-	SIMPLE_PG(uart1),
-	SIMPLE_PG(scb0),
-	SIMPLE_PG(i2s),
-	SIMPLE_PG(sdh),
-	SIMPLE_PG(sdio),
-
-	/* pseudo-pingroups for each GPIO pin follow */
-};
-
-/**
- * struct tz1090_pmx - Private pinctrl data
- * @dev:	Platform device
- * @pctl:	Pin control device
- * @regs:	Register region
- * @lock:	Lock protecting coherency of pin_en, gpio_en, and SELECT regs
- * @pin_en:	Pins that have been enabled (32 pins packed into each element)
- * @gpio_en:	GPIOs that have been enabled (32 pins packed into each element)
- */
-struct tz1090_pmx {
-	struct device		*dev;
-	struct pinctrl_dev	*pctl;
-	void __iomem		*regs;
-	spinlock_t		lock;
-	u32			pin_en[3];
-	u32			gpio_en[3];
-};
-
-static inline u32 pmx_read(struct tz1090_pmx *pmx, u32 reg)
-{
-	return ioread32(pmx->regs + reg);
-}
-
-static inline void pmx_write(struct tz1090_pmx *pmx, u32 val, u32 reg)
-{
-	iowrite32(val, pmx->regs + reg);
-}
-
-/*
- * Pin control operations
- */
-
-/* each GPIO pin has it's own pseudo pingroup containing only itself */
-
-static int tz1090_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
-{
-	return ARRAY_SIZE(tz1090_groups) + NUM_GPIOS;
-}
-
-static const char *tz1090_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
-						 unsigned int group)
-{
-	if (group < ARRAY_SIZE(tz1090_groups)) {
-		/* normal pingroup */
-		return tz1090_groups[group].name;
-	} else {
-		/* individual gpio pin pseudo-pingroup */
-		unsigned int pin = group - ARRAY_SIZE(tz1090_groups);
-		return tz1090_pins[pin].name;
-	}
-}
-
-static int tz1090_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
-					 unsigned int group,
-					 const unsigned int **pins,
-					 unsigned int *num_pins)
-{
-	if (group < ARRAY_SIZE(tz1090_groups)) {
-		/* normal pingroup */
-		*pins = tz1090_groups[group].pins;
-		*num_pins = tz1090_groups[group].npins;
-	} else {
-		/* individual gpio pin pseudo-pingroup */
-		unsigned int pin = group - ARRAY_SIZE(tz1090_groups);
-		*pins = &tz1090_pins[pin].number;
-		*num_pins = 1;
-	}
-
-	return 0;
-}
-
-#ifdef CONFIG_DEBUG_FS
-static void tz1090_pinctrl_pin_dbg_show(struct pinctrl_dev *pctldev,
-					struct seq_file *s,
-					unsigned int offset)
-{
-	seq_printf(s, " %s", dev_name(pctldev->dev));
-}
-#endif
-
-static int reserve_map(struct device *dev, struct pinctrl_map **map,
-		       unsigned int *reserved_maps, unsigned int *num_maps,
-		       unsigned int reserve)
-{
-	unsigned int old_num = *reserved_maps;
-	unsigned int new_num = *num_maps + reserve;
-	struct pinctrl_map *new_map;
-
-	if (old_num >= new_num)
-		return 0;
-
-	new_map = krealloc(*map, sizeof(*new_map) * new_num, GFP_KERNEL);
-	if (!new_map) {
-		dev_err(dev, "krealloc(map) failed\n");
-		return -ENOMEM;
-	}
-
-	memset(new_map + old_num, 0, (new_num - old_num) * sizeof(*new_map));
-
-	*map = new_map;
-	*reserved_maps = new_num;
-
-	return 0;
-}
-
-static int add_map_mux(struct pinctrl_map **map, unsigned int *reserved_maps,
-		       unsigned int *num_maps, const char *group,
-		       const char *function)
-{
-	if (WARN_ON(*num_maps == *reserved_maps))
-		return -ENOSPC;
-
-	(*map)[*num_maps].type = PIN_MAP_TYPE_MUX_GROUP;
-	(*map)[*num_maps].data.mux.group = group;
-	(*map)[*num_maps].data.mux.function = function;
-	(*num_maps)++;
-
-	return 0;
-}
-
-static int add_map_configs(struct device *dev,
-			   struct pinctrl_map **map,
-			   unsigned int *reserved_maps, unsigned int *num_maps,
-			   const char *group, unsigned long *configs,
-			   unsigned int num_configs)
-{
-	unsigned long *dup_configs;
-
-	if (WARN_ON(*num_maps == *reserved_maps))
-		return -ENOSPC;
-
-	dup_configs = kmemdup(configs, num_configs * sizeof(*dup_configs),
-			      GFP_KERNEL);
-	if (!dup_configs)
-		return -ENOMEM;
-
-	(*map)[*num_maps].type = PIN_MAP_TYPE_CONFIGS_GROUP;
-	(*map)[*num_maps].data.configs.group_or_pin = group;
-	(*map)[*num_maps].data.configs.configs = dup_configs;
-	(*map)[*num_maps].data.configs.num_configs = num_configs;
-	(*num_maps)++;
-
-	return 0;
-}
-
-static void tz1090_pinctrl_dt_free_map(struct pinctrl_dev *pctldev,
-				       struct pinctrl_map *map,
-				       unsigned int num_maps)
-{
-	int i;
-
-	for (i = 0; i < num_maps; i++)
-		if (map[i].type == PIN_MAP_TYPE_CONFIGS_GROUP)
-			kfree(map[i].data.configs.configs);
-
-	kfree(map);
-}
-
-static int tz1090_pinctrl_dt_subnode_to_map(struct device *dev,
-					    struct device_node *np,
-					    struct pinctrl_map **map,
-					    unsigned int *reserved_maps,
-					    unsigned int *num_maps)
-{
-	int ret;
-	const char *function;
-	unsigned long *configs = NULL;
-	unsigned int num_configs = 0;
-	unsigned int reserve;
-	struct property *prop;
-	const char *group;
-
-	ret = of_property_read_string(np, "tz1090,function", &function);
-	if (ret < 0) {
-		/* EINVAL=missing, which is fine since it's optional */
-		if (ret != -EINVAL)
-			dev_err(dev, "could not parse property function\n");
-		function = NULL;
-	}
-
-	ret = pinconf_generic_parse_dt_config(np, NULL, &configs, &num_configs);
-	if (ret)
-		return ret;
-
-	reserve = 0;
-	if (function != NULL)
-		reserve++;
-	if (num_configs)
-		reserve++;
-	ret = of_property_count_strings(np, "tz1090,pins");
-	if (ret < 0) {
-		dev_err(dev, "could not parse property pins\n");
-		goto exit;
-	}
-	reserve *= ret;
-
-	ret = reserve_map(dev, map, reserved_maps, num_maps, reserve);
-	if (ret < 0)
-		goto exit;
-
-	of_property_for_each_string(np, "tz1090,pins", prop, group) {
-		if (function) {
-			ret = add_map_mux(map, reserved_maps, num_maps,
-					  group, function);
-			if (ret < 0)
-				goto exit;
-		}
-
-		if (num_configs) {
-			ret = add_map_configs(dev, map, reserved_maps,
-					      num_maps, group, configs,
-					      num_configs);
-			if (ret < 0)
-				goto exit;
-		}
-	}
-
-	ret = 0;
-
-exit:
-	kfree(configs);
-	return ret;
-}
-
-static int tz1090_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev,
-					 struct device_node *np_config,
-					 struct pinctrl_map **map,
-					 unsigned int *num_maps)
-{
-	unsigned int reserved_maps;
-	struct device_node *np;
-	int ret;
-
-	reserved_maps = 0;
-	*map = NULL;
-	*num_maps = 0;
-
-	for_each_child_of_node(np_config, np) {
-		ret = tz1090_pinctrl_dt_subnode_to_map(pctldev->dev, np, map,
-						       &reserved_maps,
-						       num_maps);
-		if (ret < 0) {
-			tz1090_pinctrl_dt_free_map(pctldev, *map, *num_maps);
-			return ret;
-		}
-	}
-
-	return 0;
-}
-
-static const struct pinctrl_ops tz1090_pinctrl_ops = {
-	.get_groups_count	= tz1090_pinctrl_get_groups_count,
-	.get_group_name		= tz1090_pinctrl_get_group_name,
-	.get_group_pins		= tz1090_pinctrl_get_group_pins,
-#ifdef CONFIG_DEBUG_FS
-	.pin_dbg_show		= tz1090_pinctrl_pin_dbg_show,
-#endif
-	.dt_node_to_map		= tz1090_pinctrl_dt_node_to_map,
-	.dt_free_map		= tz1090_pinctrl_dt_free_map,
-};
-
-/*
- * Pin mux operations
- */
-
-static int tz1090_pinctrl_get_funcs_count(struct pinctrl_dev *pctldev)
-{
-	return ARRAY_SIZE(tz1090_functions);
-}
-
-static const char *tz1090_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
-						unsigned int function)
-{
-	return tz1090_functions[function].name;
-}
-
-static int tz1090_pinctrl_get_func_groups(struct pinctrl_dev *pctldev,
-					  unsigned int function,
-					  const char * const **groups,
-					  unsigned int * const num_groups)
-{
-	/* pingroup functions */
-	*groups = tz1090_functions[function].groups;
-	*num_groups = tz1090_functions[function].ngroups;
-	return 0;
-}
-
-/**
- * tz1090_pinctrl_select() - update bit in SELECT register
- * @pmx:		Pinmux data
- * @pin:		Pin number (must be within GPIO range)
- */
-static void tz1090_pinctrl_select(struct tz1090_pmx *pmx,
-				  unsigned int pin)
-{
-	u32 reg, reg_shift, select, val;
-	unsigned int pmx_index, pmx_shift;
-	unsigned long flags;
-
-	/* uses base 32 instead of base 30 */
-	pmx_index = pin >> 5;
-	pmx_shift = pin & 0x1f;
-
-	/* select = !perip || gpio */
-	select = ((~pmx->pin_en[pmx_index] |
-		   pmx->gpio_en[pmx_index]) >> pmx_shift) & 1;
-
-	/* find register and bit offset (base 30) */
-	reg = REG_PINCTRL_SELECT + 4*(pin / 30);
-	reg_shift = pin % 30;
-
-	/* modify gpio select bit */
-	__global_lock2(flags);
-	val = pmx_read(pmx, reg);
-	val &= ~BIT(reg_shift);
-	val |= select << reg_shift;
-	pmx_write(pmx, val, reg);
-	__global_unlock2(flags);
-}
-
-/**
- * tz1090_pinctrl_gpio_select() - enable/disable GPIO usage for a pin
- * @pmx:		Pinmux data
- * @pin:		Pin number
- * @gpio_select:	true to enable pin as GPIO,
- *			false to leave control to whatever function is enabled
- *
- * Records that GPIO usage is enabled/disabled so that enabling a function
- * doesn't override the SELECT register bit.
- */
-static void tz1090_pinctrl_gpio_select(struct tz1090_pmx *pmx,
-				       unsigned int pin,
-				       bool gpio_select)
-{
-	unsigned int index, shift;
-	u32 gpio_en;
-
-	if (pin >= NUM_GPIOS)
-		return;
-
-	/* uses base 32 instead of base 30 */
-	index = pin >> 5;
-	shift = pin & 0x1f;
-
-	spin_lock(&pmx->lock);
-
-	/* keep a record whether gpio is selected */
-	gpio_en = pmx->gpio_en[index];
-	gpio_en &= ~BIT(shift);
-	if (gpio_select)
-		gpio_en |= BIT(shift);
-	pmx->gpio_en[index] = gpio_en;
-
-	/* update the select bit */
-	tz1090_pinctrl_select(pmx, pin);
-
-	spin_unlock(&pmx->lock);
-}
-
-/**
- * tz1090_pinctrl_perip_select() - enable/disable peripheral interface for a pin
- * @pmx:		Pinmux data
- * @pin:		Pin number
- * @perip_select:	true to enable peripheral interface when not GPIO,
- *			false to leave pin in GPIO mode
- *
- * Records that peripheral usage is enabled/disabled so that SELECT register can
- * be set appropriately when GPIO is disabled.
- */
-static void tz1090_pinctrl_perip_select(struct tz1090_pmx *pmx,
-					unsigned int pin,
-					bool perip_select)
-{
-	unsigned int index, shift;
-	u32 pin_en;
-
-	if (pin >= NUM_GPIOS)
-		return;
-
-	/* uses base 32 instead of base 30 */
-	index = pin >> 5;
-	shift = pin & 0x1f;
-
-	spin_lock(&pmx->lock);
-
-	/* keep a record whether peripheral is selected */
-	pin_en = pmx->pin_en[index];
-	pin_en &= ~BIT(shift);
-	if (perip_select)
-		pin_en |= BIT(shift);
-	pmx->pin_en[index] = pin_en;
-
-	/* update the select bit */
-	tz1090_pinctrl_select(pmx, pin);
-
-	spin_unlock(&pmx->lock);
-}
-
-/**
- * tz1090_pinctrl_enable_mux() - Switch a pin mux group to a function.
- * @pmx:		Pinmux data
- * @desc:		Pinmux description
- * @function:		Function to switch to
- *
- * Enable a particular function on a pin mux group. Since pin mux descriptions
- * are nested this function is recursive.
- */
-static int tz1090_pinctrl_enable_mux(struct tz1090_pmx *pmx,
-				     const struct tz1090_muxdesc *desc,
-				     unsigned int function)
-{
-	const int *fit;
-	unsigned long flags;
-	int mux;
-	unsigned int func, ret;
-	u32 reg, mask;
-
-	/* find the mux value for this function, searching recursively */
-	for (mux = 0, fit = desc->funcs;
-	     mux < ARRAY_SIZE(desc->funcs); ++mux, ++fit) {
-		func = *fit;
-		if (func == function)
-			goto found_mux;
-
-		/* maybe it's a sub-mux */
-		if (func < ARRAY_SIZE(tz1090_submux) && tz1090_submux[func]) {
-			ret = tz1090_pinctrl_enable_mux(pmx,
-							tz1090_submux[func],
-							function);
-			if (!ret)
-				goto found_mux;
-		}
-	}
-
-	return -EINVAL;
-found_mux:
-
-	/* Set up the mux */
-	if (desc->width) {
-		mask = (BIT(desc->width) - 1) << desc->bit;
-		__global_lock2(flags);
-		reg = pmx_read(pmx, desc->reg);
-		reg &= ~mask;
-		reg |= (mux << desc->bit) & mask;
-		pmx_write(pmx, reg, desc->reg);
-		__global_unlock2(flags);
-	}
-
-	return 0;
-}
-
-/**
- * tz1090_pinctrl_enable() - Enable a function on a pin group.
- * @pctldev:		Pin control data
- * @function:		Function index to enable
- * @group:		Group index to enable
- *
- * Enable a particular function on a group of pins. The per GPIO pin pseudo pin
- * groups can be used (in which case the pin will be enabled in peripheral mode
- * and if it belongs to a pin mux group the mux will be switched if it isn't
- * already in use. Some convenience pin groups can also be used in which case
- * the effect is the same as enabling the function on each individual pin in the
- * group.
- */
-static int tz1090_pinctrl_set_mux(struct pinctrl_dev *pctldev,
-				  unsigned int function, unsigned int group)
-{
-	struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	struct tz1090_pingroup *grp;
-	int ret;
-	unsigned int pin_num, mux_group, i, npins;
-	const unsigned int *pins;
-
-	/* group of pins? */
-	if (group < ARRAY_SIZE(tz1090_groups)) {
-		grp = &tz1090_groups[group];
-		npins = grp->npins;
-		pins = grp->pins;
-		/*
-		 * All pins in the group must belong to the same mux group,
-		 * which allows us to just use the mux group of the first pin.
-		 * By explicitly listing permitted pingroups for each function
-		 * the pinmux core should ensure this is always the case.
-		 */
-	} else {
-		pin_num = group - ARRAY_SIZE(tz1090_groups);
-		npins = 1;
-		pins = &pin_num;
-	}
-	mux_group = tz1090_mux_pins[*pins];
-
-	/* no mux group, but can still be individually muxed to peripheral */
-	if (mux_group >= TZ1090_MUX_GROUP_MAX) {
-		if (function == TZ1090_MUX_PERIP)
-			goto mux_pins;
-		return -EINVAL;
-	}
-
-	/* mux group already set to a different function? */
-	grp = &tz1090_mux_groups[mux_group];
-	if (grp->func_count && grp->func != function) {
-		dev_err(pctldev->dev,
-			"%s: can't mux pin(s) to '%s', group already muxed to '%s'\n",
-			__func__, tz1090_functions[function].name,
-			tz1090_functions[grp->func].name);
-		return -EBUSY;
-	}
-
-	dev_dbg(pctldev->dev, "%s: muxing %u pin(s) in '%s' to '%s'\n",
-		__func__, npins, grp->name, tz1090_functions[function].name);
-
-	/* if first pin in mux group to be enabled, enable the group mux */
-	if (!grp->func_count) {
-		grp->func = function;
-		ret = tz1090_pinctrl_enable_mux(pmx, &grp->mux, function);
-		if (ret)
-			return ret;
-	}
-	/* add pins to ref count and mux individually to peripheral */
-	grp->func_count += npins;
-mux_pins:
-	for (i = 0; i < npins; ++i)
-		tz1090_pinctrl_perip_select(pmx, pins[i], true);
-
-	return 0;
-}
-
-/**
- * tz1090_pinctrl_gpio_request_enable() - Put pin in GPIO mode.
- * @pctldev:		Pin control data
- * @range:		GPIO range
- * @pin:		Pin number
- *
- * Puts a particular pin into GPIO mode, disabling peripheral control until it's
- * disabled again.
- */
-static int tz1090_pinctrl_gpio_request_enable(struct pinctrl_dev *pctldev,
-					      struct pinctrl_gpio_range *range,
-					      unsigned int pin)
-{
-	struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	tz1090_pinctrl_gpio_select(pmx, pin, true);
-	return 0;
-}
-
-/**
- * tz1090_pinctrl_gpio_disable_free() - Take pin out of GPIO mode.
- * @pctldev:		Pin control data
- * @range:		GPIO range
- * @pin:		Pin number
- *
- * Take a particular pin out of GPIO mode. If the pin is enabled for a
- * peripheral it will return to peripheral mode.
- */
-static void tz1090_pinctrl_gpio_disable_free(struct pinctrl_dev *pctldev,
-					     struct pinctrl_gpio_range *range,
-					     unsigned int pin)
-{
-	struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	tz1090_pinctrl_gpio_select(pmx, pin, false);
-}
-
-static const struct pinmux_ops tz1090_pinmux_ops = {
-	.get_functions_count	= tz1090_pinctrl_get_funcs_count,
-	.get_function_name	= tz1090_pinctrl_get_func_name,
-	.get_function_groups	= tz1090_pinctrl_get_func_groups,
-	.set_mux		= tz1090_pinctrl_set_mux,
-	.gpio_request_enable	= tz1090_pinctrl_gpio_request_enable,
-	.gpio_disable_free	= tz1090_pinctrl_gpio_disable_free,
-};
-
-/*
- * Pin config operations
- */
-
-struct tz1090_pinconf_pullup {
-	unsigned char index;
-	unsigned char shift;
-};
-
-/* The mapping of pin to pull up/down register index and shift */
-static struct tz1090_pinconf_pullup tz1090_pinconf_pullup[] = {
-	{5, 22}, /*  0 - TZ1090_PIN_SDIO_CLK */
-	{0, 14}, /*  1 - TZ1090_PIN_SDIO_CMD */
-	{0,  6}, /*  2 - TZ1090_PIN_SDIO_D0 */
-	{0,  8}, /*  3 - TZ1090_PIN_SDIO_D1 */
-	{0, 10}, /*  4 - TZ1090_PIN_SDIO_D2 */
-	{0, 12}, /*  5 - TZ1090_PIN_SDIO_D3 */
-	{0,  2}, /*  6 - TZ1090_PIN_SDH_CD */
-	{0,  4}, /*  7 - TZ1090_PIN_SDH_WP */
-	{0, 16}, /*  8 - TZ1090_PIN_SPI0_MCLK */
-	{0, 18}, /*  9 - TZ1090_PIN_SPI0_CS0 */
-	{0, 20}, /* 10 - TZ1090_PIN_SPI0_CS1 */
-	{0, 22}, /* 11 - TZ1090_PIN_SPI0_CS2 */
-	{0, 24}, /* 12 - TZ1090_PIN_SPI0_DOUT */
-	{0, 26}, /* 13 - TZ1090_PIN_SPI0_DIN */
-	{0, 28}, /* 14 - TZ1090_PIN_SPI1_MCLK */
-	{0, 30}, /* 15 - TZ1090_PIN_SPI1_CS0 */
-	{1,  0}, /* 16 - TZ1090_PIN_SPI1_CS1 */
-	{1,  2}, /* 17 - TZ1090_PIN_SPI1_CS2 */
-	{1,  4}, /* 18 - TZ1090_PIN_SPI1_DOUT */
-	{1,  6}, /* 19 - TZ1090_PIN_SPI1_DIN */
-	{1,  8}, /* 20 - TZ1090_PIN_UART0_RXD */
-	{1, 10}, /* 21 - TZ1090_PIN_UART0_TXD */
-	{1, 12}, /* 22 - TZ1090_PIN_UART0_CTS */
-	{1, 14}, /* 23 - TZ1090_PIN_UART0_RTS */
-	{1, 16}, /* 24 - TZ1090_PIN_UART1_RXD */
-	{1, 18}, /* 25 - TZ1090_PIN_UART1_TXD */
-	{1, 20}, /* 26 - TZ1090_PIN_SCB0_SDAT */
-	{1, 22}, /* 27 - TZ1090_PIN_SCB0_SCLK */
-	{1, 24}, /* 28 - TZ1090_PIN_SCB1_SDAT */
-	{1, 26}, /* 29 - TZ1090_PIN_SCB1_SCLK */
-
-	{1, 28}, /* 30 - TZ1090_PIN_SCB2_SDAT */
-	{1, 30}, /* 31 - TZ1090_PIN_SCB2_SCLK */
-	{2,  0}, /* 32 - TZ1090_PIN_I2S_MCLK */
-	{2,  2}, /* 33 - TZ1090_PIN_I2S_BCLK_OUT */
-	{2,  4}, /* 34 - TZ1090_PIN_I2S_LRCLK_OUT */
-	{2,  6}, /* 35 - TZ1090_PIN_I2S_DOUT0 */
-	{2,  8}, /* 36 - TZ1090_PIN_I2S_DOUT1 */
-	{2, 10}, /* 37 - TZ1090_PIN_I2S_DOUT2 */
-	{2, 12}, /* 38 - TZ1090_PIN_I2S_DIN */
-	{4, 12}, /* 39 - TZ1090_PIN_PDM_A */
-	{4, 14}, /* 40 - TZ1090_PIN_PDM_B */
-	{4, 18}, /* 41 - TZ1090_PIN_PDM_C */
-	{4, 20}, /* 42 - TZ1090_PIN_PDM_D */
-	{2, 14}, /* 43 - TZ1090_PIN_TFT_RED0 */
-	{2, 16}, /* 44 - TZ1090_PIN_TFT_RED1 */
-	{2, 18}, /* 45 - TZ1090_PIN_TFT_RED2 */
-	{2, 20}, /* 46 - TZ1090_PIN_TFT_RED3 */
-	{2, 22}, /* 47 - TZ1090_PIN_TFT_RED4 */
-	{2, 24}, /* 48 - TZ1090_PIN_TFT_RED5 */
-	{2, 26}, /* 49 - TZ1090_PIN_TFT_RED6 */
-	{2, 28}, /* 50 - TZ1090_PIN_TFT_RED7 */
-	{2, 30}, /* 51 - TZ1090_PIN_TFT_GREEN0 */
-	{3,  0}, /* 52 - TZ1090_PIN_TFT_GREEN1 */
-	{3,  2}, /* 53 - TZ1090_PIN_TFT_GREEN2 */
-	{3,  4}, /* 54 - TZ1090_PIN_TFT_GREEN3 */
-	{3,  6}, /* 55 - TZ1090_PIN_TFT_GREEN4 */
-	{3,  8}, /* 56 - TZ1090_PIN_TFT_GREEN5 */
-	{3, 10}, /* 57 - TZ1090_PIN_TFT_GREEN6 */
-	{3, 12}, /* 58 - TZ1090_PIN_TFT_GREEN7 */
-	{3, 14}, /* 59 - TZ1090_PIN_TFT_BLUE0 */
-
-	{3, 16}, /* 60 - TZ1090_PIN_TFT_BLUE1 */
-	{3, 18}, /* 61 - TZ1090_PIN_TFT_BLUE2 */
-	{3, 20}, /* 62 - TZ1090_PIN_TFT_BLUE3 */
-	{3, 22}, /* 63 - TZ1090_PIN_TFT_BLUE4 */
-	{3, 24}, /* 64 - TZ1090_PIN_TFT_BLUE5 */
-	{3, 26}, /* 65 - TZ1090_PIN_TFT_BLUE6 */
-	{3, 28}, /* 66 - TZ1090_PIN_TFT_BLUE7 */
-	{3, 30}, /* 67 - TZ1090_PIN_TFT_VDDEN_GD */
-	{4,  0}, /* 68 - TZ1090_PIN_TFT_PANELCLK */
-	{4,  2}, /* 69 - TZ1090_PIN_TFT_BLANK_LS */
-	{4,  4}, /* 70 - TZ1090_PIN_TFT_VSYNC_NS */
-	{4,  6}, /* 71 - TZ1090_PIN_TFT_HSYNC_NR */
-	{4,  8}, /* 72 - TZ1090_PIN_TFT_VD12ACB */
-	{4, 10}, /* 73 - TZ1090_PIN_TFT_PWRSAVE */
-	{4, 24}, /* 74 - TZ1090_PIN_TX_ON */
-	{4, 26}, /* 75 - TZ1090_PIN_RX_ON */
-	{4, 28}, /* 76 - TZ1090_PIN_PLL_ON */
-	{4, 30}, /* 77 - TZ1090_PIN_PA_ON */
-	{5,  0}, /* 78 - TZ1090_PIN_RX_HP */
-	{5,  6}, /* 79 - TZ1090_PIN_GAIN0 */
-	{5,  8}, /* 80 - TZ1090_PIN_GAIN1 */
-	{5, 10}, /* 81 - TZ1090_PIN_GAIN2 */
-	{5, 12}, /* 82 - TZ1090_PIN_GAIN3 */
-	{5, 14}, /* 83 - TZ1090_PIN_GAIN4 */
-	{5, 16}, /* 84 - TZ1090_PIN_GAIN5 */
-	{5, 18}, /* 85 - TZ1090_PIN_GAIN6 */
-	{5, 20}, /* 86 - TZ1090_PIN_GAIN7 */
-	{5,  2}, /* 87 - TZ1090_PIN_ANT_SEL0 */
-	{5,  4}, /* 88 - TZ1090_PIN_ANT_SEL1 */
-	{0,  0}, /* 89 - TZ1090_PIN_SDH_CLK_IN */
-
-	{5, 24}, /* 90 - TZ1090_PIN_TCK */
-	{5, 26}, /* 91 - TZ1090_PIN_TRST */
-	{5, 28}, /* 92 - TZ1090_PIN_TDI */
-	{5, 30}, /* 93 - TZ1090_PIN_TDO */
-	{6,  0}, /* 94 - TZ1090_PIN_TMS */
-	{4, 16}, /* 95 - TZ1090_PIN_CLK_OUT0 */
-	{4, 22}, /* 96 - TZ1090_PIN_CLK_OUT1 */
-};
-
-static int tz1090_pinconf_reg(struct pinctrl_dev *pctldev,
-			      unsigned int pin,
-			      enum pin_config_param param,
-			      bool report_err,
-			      u32 *reg, u32 *width, u32 *mask, u32 *shift,
-			      u32 *val)
-{
-	struct tz1090_pinconf_pullup *pu;
-
-	/* All supported pins have controllable input bias */
-	switch (param) {
-	case PIN_CONFIG_BIAS_DISABLE:
-	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
-		*val = REG_PU_PD_TRISTATE;
-		break;
-	case PIN_CONFIG_BIAS_PULL_UP:
-		*val = REG_PU_PD_UP;
-		break;
-	case PIN_CONFIG_BIAS_PULL_DOWN:
-		*val = REG_PU_PD_DOWN;
-		break;
-	case PIN_CONFIG_BIAS_BUS_HOLD:
-		*val = REG_PU_PD_REPEATER;
-		break;
-	default:
-		return -ENOTSUPP;
-	}
-
-	/* Only input bias parameters supported */
-	pu = &tz1090_pinconf_pullup[pin];
-	*reg = REG_PINCTRL_PU_PD + 4*pu->index;
-	*shift = pu->shift;
-	*width = 2;
-
-	/* Calculate field information */
-	*mask = (BIT(*width) - 1) << *shift;
-
-	return 0;
-}
-
-static int tz1090_pinconf_get(struct pinctrl_dev *pctldev,
-			      unsigned int pin, unsigned long *config)
-{
-	struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	enum pin_config_param param = pinconf_to_config_param(*config);
-	int ret;
-	u32 reg, width, mask, shift, val, tmp, arg;
-
-	/* Get register information */
-	ret = tz1090_pinconf_reg(pctldev, pin, param, true,
-				 &reg, &width, &mask, &shift, &val);
-	if (ret < 0)
-		return ret;
-
-	/* Extract field from register */
-	tmp = pmx_read(pmx, reg);
-	arg = ((tmp & mask) >> shift) == val;
-
-	/* Config not active */
-	if (!arg)
-		return -EINVAL;
-
-	/* And pack config */
-	*config = pinconf_to_config_packed(param, arg);
-
-	return 0;
-}
-
-static int tz1090_pinconf_set(struct pinctrl_dev *pctldev,
-			      unsigned int pin, unsigned long *configs,
-			      unsigned num_configs)
-{
-	struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	enum pin_config_param param;
-	unsigned int arg;
-	int ret;
-	u32 reg, width, mask, shift, val, tmp;
-	unsigned long flags;
-	int i;
-
-	for (i = 0; i < num_configs; i++) {
-		param = pinconf_to_config_param(configs[i]);
-		arg = pinconf_to_config_argument(configs[i]);
-
-		dev_dbg(pctldev->dev, "%s(pin=%s, config=%#lx)\n",
-			__func__, tz1090_pins[pin].name, configs[i]);
-
-		/* Get register information */
-		ret = tz1090_pinconf_reg(pctldev, pin, param, true,
-					 &reg, &width, &mask, &shift, &val);
-		if (ret < 0)
-			return ret;
-
-		/* Unpack argument and range check it */
-		if (arg > 1) {
-			dev_dbg(pctldev->dev, "%s: arg %u out of range\n",
-				__func__, arg);
-			return -EINVAL;
-		}
-
-		/* Write register field */
-		__global_lock2(flags);
-		tmp = pmx_read(pmx, reg);
-		tmp &= ~mask;
-		if (arg)
-			tmp |= val << shift;
-		pmx_write(pmx, tmp, reg);
-		__global_unlock2(flags);
-	} /* for each config */
-
-	return 0;
-}
-
-static const int tz1090_boolean_map[] = {
-	[0]		= -EINVAL,
-	[1]		= 1,
-};
-
-static const int tz1090_dr_map[] = {
-	[REG_DR_2mA]	= 2,
-	[REG_DR_4mA]	= 4,
-	[REG_DR_8mA]	= 8,
-	[REG_DR_12mA]	= 12,
-};
-
-static int tz1090_pinconf_group_reg(struct pinctrl_dev *pctldev,
-				    const struct tz1090_pingroup *g,
-				    enum pin_config_param param,
-				    bool report_err,
-				    u32 *reg, u32 *width, u32 *mask, u32 *shift,
-				    const int **map)
-{
-	/* Drive configuration applies in groups, but not to all groups. */
-	if (!g->drv) {
-		if (report_err)
-			dev_dbg(pctldev->dev,
-				"%s: group %s has no drive control\n",
-				__func__, g->name);
-		return -ENOTSUPP;
-	}
-
-	/* Find information about drive parameter's register */
-	switch (param) {
-	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
-		*reg = REG_PINCTRL_SCHMITT;
-		*width = 1;
-		*map = tz1090_boolean_map;
-		break;
-	case PIN_CONFIG_DRIVE_STRENGTH:
-		*reg = REG_PINCTRL_DR;
-		*width = 2;
-		*map = tz1090_dr_map;
-		break;
-	default:
-		return -ENOTSUPP;
-	}
-
-	/* Calculate field information */
-	*shift = g->slw_bit * *width;
-	*mask = (BIT(*width) - 1) << *shift;
-
-	return 0;
-}
-
-static int tz1090_pinconf_group_get(struct pinctrl_dev *pctldev,
-				    unsigned int group,
-				    unsigned long *config)
-{
-	struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	const struct tz1090_pingroup *g;
-	enum pin_config_param param = pinconf_to_config_param(*config);
-	int ret, arg;
-	unsigned int pin;
-	u32 reg, width, mask, shift, val;
-	const int *map;
-
-	if (group >= ARRAY_SIZE(tz1090_groups)) {
-		pin = group - ARRAY_SIZE(tz1090_groups);
-		return tz1090_pinconf_get(pctldev, pin, config);
-	}
-
-	g = &tz1090_groups[group];
-	if (g->npins == 1) {
-		pin = g->pins[0];
-		ret = tz1090_pinconf_get(pctldev, pin, config);
-		if (ret != -ENOTSUPP)
-			return ret;
-	}
-
-	/* Get register information */
-	ret = tz1090_pinconf_group_reg(pctldev, g, param, true,
-				       &reg, &width, &mask, &shift, &map);
-	if (ret < 0)
-		return ret;
-
-	/* Extract field from register */
-	val = pmx_read(pmx, reg);
-	arg = map[(val & mask) >> shift];
-	if (arg < 0)
-		return arg;
-
-	/* And pack config */
-	*config = pinconf_to_config_packed(param, arg);
-
-	return 0;
-}
-
-static int tz1090_pinconf_group_set(struct pinctrl_dev *pctldev,
-				    unsigned int group, unsigned long *configs,
-				    unsigned num_configs)
-{
-	struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
-	const struct tz1090_pingroup *g;
-	enum pin_config_param param;
-	unsigned int arg, pin, i;
-	const unsigned int *pit;
-	int ret;
-	u32 reg, width, mask, shift, val;
-	unsigned long flags;
-	const int *map;
-	int j;
-
-	if (group >= ARRAY_SIZE(tz1090_groups)) {
-		pin = group - ARRAY_SIZE(tz1090_groups);
-		return tz1090_pinconf_set(pctldev, pin, configs, num_configs);
-	}
-
-	g = &tz1090_groups[group];
-	if (g->npins == 1) {
-		pin = g->pins[0];
-		ret = tz1090_pinconf_set(pctldev, pin, configs, num_configs);
-		if (ret != -ENOTSUPP)
-			return ret;
-	}
-
-	for (j = 0; j < num_configs; j++) {
-		param = pinconf_to_config_param(configs[j]);
-
-		dev_dbg(pctldev->dev, "%s(group=%s, config=%#lx)\n",
-			__func__, g->name, configs[j]);
-
-		/* Get register information */
-		ret = tz1090_pinconf_group_reg(pctldev, g, param, true, &reg,
-						&width, &mask, &shift, &map);
-		if (ret < 0) {
-			/*
-			 * Maybe we're trying to set a per-pin configuration
-			 * of a group, so do the pins one by one. This is
-			 * mainly as a convenience.
-			 */
-			for (i = 0, pit = g->pins; i < g->npins; ++i, ++pit) {
-				ret = tz1090_pinconf_set(pctldev, *pit, configs,
-					num_configs);
-				if (ret)
-					return ret;
-			}
-			return 0;
-		}
-
-		/* Unpack argument and map it to register value */
-		arg = pinconf_to_config_argument(configs[j]);
-		for (i = 0; i < BIT(width); ++i) {
-			if (map[i] == arg || (map[i] == -EINVAL && !arg)) {
-				/* Write register field */
-				__global_lock2(flags);
-				val = pmx_read(pmx, reg);
-				val &= ~mask;
-				val |= i << shift;
-				pmx_write(pmx, val, reg);
-				__global_unlock2(flags);
-				goto next_config;
-			}
-		}
-
-		dev_dbg(pctldev->dev, "%s: arg %u not supported\n",
-			__func__, arg);
-		return -EINVAL;
-
-next_config:
-		;
-	} /* for each config */
-
-	return 0;
-}
-
-static const struct pinconf_ops tz1090_pinconf_ops = {
-	.is_generic			= true,
-	.pin_config_get			= tz1090_pinconf_get,
-	.pin_config_set			= tz1090_pinconf_set,
-	.pin_config_group_get		= tz1090_pinconf_group_get,
-	.pin_config_group_set		= tz1090_pinconf_group_set,
-	.pin_config_config_dbg_show	= pinconf_generic_dump_config,
-};
-
-/*
- * Pin control driver setup
- */
-
-static struct pinctrl_desc tz1090_pinctrl_desc = {
-	.pctlops	= &tz1090_pinctrl_ops,
-	.pmxops		= &tz1090_pinmux_ops,
-	.confops	= &tz1090_pinconf_ops,
-	.owner		= THIS_MODULE,
-};
-
-static int tz1090_pinctrl_probe(struct platform_device *pdev)
-{
-	struct tz1090_pmx *pmx;
-	struct resource *res;
-
-	pmx = devm_kzalloc(&pdev->dev, sizeof(*pmx), GFP_KERNEL);
-	if (!pmx)
-		return -ENOMEM;
-
-	pmx->dev = &pdev->dev;
-	spin_lock_init(&pmx->lock);
-
-	tz1090_pinctrl_desc.name = dev_name(&pdev->dev);
-	tz1090_pinctrl_desc.pins = tz1090_pins;
-	tz1090_pinctrl_desc.npins = ARRAY_SIZE(tz1090_pins);
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	pmx->regs = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(pmx->regs))
-		return PTR_ERR(pmx->regs);
-
-	pmx->pctl = devm_pinctrl_register(&pdev->dev, &tz1090_pinctrl_desc,
-					  pmx);
-	if (IS_ERR(pmx->pctl)) {
-		dev_err(&pdev->dev, "Couldn't register pinctrl driver\n");
-		return PTR_ERR(pmx->pctl);
-	}
-
-	platform_set_drvdata(pdev, pmx);
-
-	dev_info(&pdev->dev, "TZ1090 pinctrl driver initialised\n");
-
-	return 0;
-}
-
-static const struct of_device_id tz1090_pinctrl_of_match[] = {
-	{ .compatible = "img,tz1090-pinctrl", },
-	{ },
-};
-
-static struct platform_driver tz1090_pinctrl_driver = {
-	.driver = {
-		.name		= "tz1090-pinctrl",
-		.of_match_table	= tz1090_pinctrl_of_match,
-	},
-	.probe	= tz1090_pinctrl_probe,
-};
-
-static int __init tz1090_pinctrl_init(void)
-{
-	tz1090_init_mux_pins();
-	return platform_driver_register(&tz1090_pinctrl_driver);
-}
-arch_initcall(tz1090_pinctrl_init);
-
-static void __exit tz1090_pinctrl_exit(void)
-{
-	platform_driver_unregister(&tz1090_pinctrl_driver);
-}
-module_exit(tz1090_pinctrl_exit);
-
-MODULE_AUTHOR("Imagination Technologies Ltd.");
-MODULE_DESCRIPTION("Toumaz Xenif TZ1090 pinctrl driver");
-MODULE_LICENSE("GPL v2");
-MODULE_DEVICE_TABLE(of, tz1090_pinctrl_of_match);