ath10k: disable sta keepalive

Firmware revisions providing sta keepalive service
have it enabled by default.

mac80211 already does idle connection polling so
it makes no sense to duplicate this in ath10k.
mac80211 wouldn't even know of the offloaded
keepalive NullFunc frames.

This prevents sending out some extraneous frames
on the air.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

drivers/net/wireless/ath/ath10k/mac.c

@@ -1286,6 +1286,38 @@ static int ath10k_mac_vif_setup_ps(struct ath10k_vif *arvif)
 	return 0;
 }
 
+static int ath10k_mac_vif_disable_keepalive(struct ath10k_vif *arvif)
+{
+	struct ath10k *ar = arvif->ar;
+	struct wmi_sta_keepalive_arg arg = {};
+	int ret;
+
+	lockdep_assert_held(&arvif->ar->conf_mutex);
+
+	if (arvif->vdev_type != WMI_VDEV_TYPE_STA)
+		return 0;
+
+	if (!test_bit(WMI_SERVICE_STA_KEEP_ALIVE, ar->wmi.svc_map))
+		return 0;
+
+	/* Some firmware revisions have a bug and ignore the `enabled` field.
+	 * Instead use the interval to disable the keepalive.
+	 */
+	arg.vdev_id = arvif->vdev_id;
+	arg.enabled = 1;
+	arg.method = WMI_STA_KEEPALIVE_METHOD_NULL_FRAME;
+	arg.interval = WMI_STA_KEEPALIVE_INTERVAL_DISABLE;
+
+	ret = ath10k_wmi_sta_keepalive(ar, &arg);
+	if (ret) {
+		ath10k_warn(ar, "failed to submit keepalive on vdev %i: %d\n",
+			    arvif->vdev_id, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
 /**********************/
 /* Station management */
 /**********************/
@@ -3180,6 +3212,16 @@ static int ath10k_add_interface(struct ieee80211_hw *hw,
 	ar->free_vdev_map &= ~(1LL << arvif->vdev_id);
 	list_add(&arvif->list, &ar->arvifs);
 
+	/* It makes no sense to have firmware do keepalives. mac80211 already
+	 * takes care of this with idle connection polling.
+	 */
+	ret = ath10k_mac_vif_disable_keepalive(arvif);
+	if (ret) {
+		ath10k_warn(ar, "failed to disable keepalive on vdev %i: %d\n",
+			    arvif->vdev_id, ret);
+		goto err_vdev_delete;
+	}
+
 	vdev_param = ar->wmi.vdev_param->def_keyid;
 	ret = ath10k_wmi_vdev_set_param(ar, 0, vdev_param,
 					arvif->def_wep_key_idx);

drivers/net/wireless/ath/ath10k/wmi.h

@@ -4665,6 +4665,11 @@ enum wmi_sta_keepalive_method {
 	WMI_STA_KEEPALIVE_METHOD_UNSOLICITATED_ARP_RESPONSE = 2,
 };
 
+#define WMI_STA_KEEPALIVE_INTERVAL_DISABLE 0
+
+/* Firmware crashes if keepalive interval exceeds this limit */
+#define WMI_STA_KEEPALIVE_INTERVAL_MAX_SECONDS 0xffff
+
 /* note: ip4 addresses are in network byte order, i.e. big endian */
 struct wmi_sta_keepalive_arp_resp {
 	__be32 src_ip4_addr;