Merge branch 'for-4.19/cougar' into for-linus

New device support for hid-cougar

Documentation/ABI/obsolete/sysfs-gpio

@@ -11,7 +11,7 @@ Description:
   Kernel code may export it for complete or partial access.
 
   GPIOs are identified as they are inside the kernel, using integers in
-  the range 0..INT_MAX.  See Documentation/gpio/gpio.txt for more information.
+  the range 0..INT_MAX.  See Documentation/gpio for more information.
 
     /sys/class/gpio
 	/export ... asks the kernel to export a GPIO to userspace

Documentation/ABI/removed/sysfs-bus-nfit

@@ -0,0 +1,17 @@
+What:		/sys/bus/nd/devices/regionX/nfit/ecc_unit_size
+Date:		Aug, 2017
+KernelVersion:	v4.14 (Removed v4.18)
+Contact:	linux-nvdimm@lists.01.org
+Description:
+		(RO) Size of a write request to a DIMM that will not incur a
+		read-modify-write cycle at the memory controller.
+
+		When the nfit driver initializes it runs an ARS (Address Range
+		Scrub) operation across every pmem range. Part of that process
+		involves determining the ARS capabilities of a given address
+		range. One of the capabilities that is reported is the 'Clear
+		Uncorrectable Error Range Length Unit Size' (see: ACPI 6.2
+		section 9.20.7.4 Function Index 1 - Query ARS Capabilities).
+		This property indicates the boundary at which the NVDIMM may
+		need to perform read-modify-write cycles to maintain ECC (Error
+		Correcting Code) blocks.

Documentation/ABI/testing/sysfs-bus-iio

@@ -190,6 +190,13 @@ Description:
 		but should match other such assignments on device).
 		Units after application of scale and offset are m/s^2.
 
+What:		/sys/bus/iio/devices/iio:deviceX/in_angl_raw
+KernelVersion:	4.17
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Angle of rotation. Units after application of scale and offset
+		are radians.
+
 What:		/sys/bus/iio/devices/iio:deviceX/in_anglvel_x_raw
 What:		/sys/bus/iio/devices/iio:deviceX/in_anglvel_y_raw
 What:		/sys/bus/iio/devices/iio:deviceX/in_anglvel_z_raw
@@ -297,6 +304,7 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_pressure_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_humidityrelative_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_magn_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_rot_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_angl_offset
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -350,6 +358,7 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_humidityrelative_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_illuminance_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_countY_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_angl_scale
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org
 Description:

Documentation/ABI/testing/sysfs-bus-nfit

@@ -212,22 +212,3 @@ Description:
 		range. Used by NVDIMM Region Mapping Structure to uniquely refer
 		to this structure. Value of 0 is reserved and not used as an
 		index.
-
-
-What:		/sys/bus/nd/devices/regionX/nfit/ecc_unit_size
-Date:		Aug, 2017
-KernelVersion:	v4.14
-Contact:	linux-nvdimm@lists.01.org
-Description:
-		(RO) Size of a write request to a DIMM that will not incur a
-		read-modify-write cycle at the memory controller.
-
-		When the nfit driver initializes it runs an ARS (Address Range
-		Scrub) operation across every pmem range. Part of that process
-		involves determining the ARS capabilities of a given address
-		range. One of the capabilities that is reported is the 'Clear
-		Uncorrectable Error Range Length Unit Size' (see: ACPI 6.2
-		section 9.20.7.4 Function Index 1 - Query ARS Capabilities).
-		This property indicates the boundary at which the NVDIMM may
-		need to perform read-modify-write cycles to maintain ECC (Error
-		Correcting Code) blocks.

Documentation/ABI/testing/sysfs-bus-rpmsg

@@ -73,3 +73,23 @@ Description:
 		This sysfs entry tells us whether the channel is a local
 		server channel that is announced (values are either
 		true or false).
+
+What:		/sys/bus/rpmsg/devices/.../driver_override
+Date:		April 2018
+KernelVersion:	4.18
+Contact:	Bjorn Andersson <bjorn.andersson@linaro.org>
+Description:
+		Every rpmsg device is a communication channel with a remote
+		processor. Channels are identified by a textual name (see
+		/sys/bus/rpmsg/devices/.../name above) and have a local
+		("source") rpmsg address, and remote ("destination") rpmsg
+		address.
+
+		The listening entity (or client) which communicates with a
+		remote processor is referred as rpmsg driver. The rpmsg device
+		and rpmsg driver are matched based on rpmsg device name and
+		rpmsg driver ID table.
+
+		This sysfs entry allows the rpmsg driver for a rpmsg device
+		to be specified which will override standard OF, ID table
+		and name matching.

Documentation/ABI/testing/sysfs-class-mtd

@@ -232,3 +232,11 @@ Description:
 		of the parent (another partition or a flash device) in bytes.
 		This attribute is absent on flash devices, so it can be used
 		to distinguish them from partitions.
+
+What:		/sys/class/mtd/mtdX/oobavail
+Date:		April 2018
+KernelVersion:	4.16
+Contact:	linux-mtd@lists.infradead.org
+Description:
+		Number of bytes available for a client to place data into
+		the out of band area.

Documentation/ABI/testing/sysfs-devices-system-cpu

@@ -238,9 +238,6 @@ Description:	Discover and change clock speed of CPUs
 
 		See files in Documentation/cpu-freq/ for more information.
 
-		In particular, read Documentation/cpu-freq/user-guide.txt
-		to learn how to control the knobs.
-
 
 What:		/sys/devices/system/cpu/cpu#/cpufreq/freqdomain_cpus
 Date:		June 2013

Documentation/ABI/testing/sysfs-fs-f2fs

@@ -101,6 +101,7 @@ Date:		February 2015
 Contact:	"Jaegeuk Kim" <jaegeuk@kernel.org>
 Description:
 		 Controls the trimming rate in batch mode.
+		 <deprecated>
 
 What:		/sys/fs/f2fs/<disk>/cp_interval
 Date:		October 2015
@@ -140,7 +141,7 @@ Contact:	"Shuoran Liu" <liushuoran@huawei.com>
 Description:
 		 Shows total written kbytes issued to disk.
 
-What:		/sys/fs/f2fs/<disk>/feature
+What:		/sys/fs/f2fs/<disk>/features
 Date:		July 2017
 Contact:	"Jaegeuk Kim" <jaegeuk@kernel.org>
 Description:

Documentation/ABI/testing/sysfs-platform-ideapad-laptop

@@ -25,3 +25,16 @@ Description:
 		Control touchpad mode.
 			* 1 -> Switched On
 			* 0 -> Switched Off
+
+What:		/sys/bus/pci/devices/<bdf>/<device>/VPC2004:00/fn_lock
+Date:		May 2018
+KernelVersion:	4.18
+Contact:	"Oleg Keri <ezhi99@gmail.com>"
+Description:
+		Control fn-lock mode.
+			* 1 -> Switched On
+			* 0 -> Switched Off
+
+		For example:
+		# echo "0" >	\
+		/sys/bus/pci/devices/0000:00:1f.0/PNP0C09:00/VPC2004:00/fn_lock

Documentation/acpi/method-customizing.txt

@@ -16,7 +16,8 @@ control method rather than override the entire DSDT, because kernel
 rebuild/reboot is not needed and test result can be got in minutes.
 
 Note: Only ACPI METHOD can be overridden, any other object types like
-      "Device", "OperationRegion", are not recognized.
+      "Device", "OperationRegion", are not recognized. Methods
+      declared inside scope operators are also not supported.
 Note: The same ACPI control method can be overridden for many times,
       and it's always the latest one that used by Linux/kernel.
 Note: To get the ACPI debug object output (Store (AAAA, Debug)),
@@ -32,8 +33,6 @@ Note: To get the ACPI debug object output (Store (AAAA, Debug)),
 
       DefinitionBlock ("", "SSDT", 1, "", "", 0x20080715)
       {
-	External (ACON)
-
 	Method (\_SB_.AC._PSR, 0, NotSerialized)
 	{
 		Store ("In AC _PSR", Debug)
@@ -42,9 +41,10 @@ Note: To get the ACPI debug object output (Store (AAAA, Debug)),
       }
       Note that the full pathname of the method in ACPI namespace
       should be used.
-      And remember to use "External" to declare external objects.
    e) assemble the file to generate the AML code of the method.
-      e.g. "iasl psr.asl" (psr.aml is generated as a result)
+      e.g. "iasl -vw 6084 psr.asl" (psr.aml is generated as a result)
+      If parameter "-vw 6084" is not supported by your iASL compiler,
+      please try a newer version.
    f) mount debugfs by "mount -t debugfs none /sys/kernel/debug"
    g) override the old method via the debugfs by running
       "cat /tmp/psr.aml > /sys/kernel/debug/acpi/custom_method"

Documentation/admin-guide/LSM/apparmor.rst

@@ -44,8 +44,8 @@ Links
 
 Mailing List - apparmor@lists.ubuntu.com
 
-Wiki - http://apparmor.wiki.kernel.org/
+Wiki - http://wiki.apparmor.net
 
-User space tools - https://launchpad.net/apparmor
+User space tools - https://gitlab.com/apparmor
 
-Kernel module - git://git.kernel.org/pub/scm/linux/kernel/git/jj/apparmor-dev.git
+Kernel module - git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor

Documentation/admin-guide/kernel-parameters.txt

@@ -256,7 +256,7 @@
 				(may crash computer or cause data corruption)
 
 	ALSA		[HW,ALSA]
-			See Documentation/sound/alsa/alsa-parameters.txt
+			See Documentation/sound/alsa-configuration.rst
 
 	alignment=	[KNL,ARM]
 			Allow the default userspace alignment fault handler
@@ -2926,9 +2926,6 @@
 			This will also cause panics on machine check exceptions.
 			Useful together with panic=30 to trigger a reboot.
 
-	OSS		[HW,OSS]
-			See Documentation/sound/oss/oss-parameters.txt
-
 	page_owner=	[KNL] Boot-time page_owner enabling option.
 			Storage of the information about who allocated
 			each page is disabled in default. With this switch,
@@ -4106,6 +4103,23 @@
 			expediting.  Set to zero to disable automatic
 			expediting.
 
+	ssbd=		[ARM64,HW]
+			Speculative Store Bypass Disable control
+
+			On CPUs that are vulnerable to the Speculative
+			Store Bypass vulnerability and offer a
+			firmware based mitigation, this parameter
+			indicates how the mitigation should be used:
+
+			force-on:  Unconditionally enable mitigation for
+				   for both kernel and userspace
+			force-off: Unconditionally disable mitigation for
+				   for both kernel and userspace
+			kernel:    Always enable mitigation in the
+				   kernel, and offer a prctl interface
+				   to allow userspace to register its
+				   interest in being mitigated too.
+
 	stack_guard_gap=	[MM]
 			override the default stack gap protection. The value
 			is in page units and it defines how many pages prior
@@ -4318,7 +4332,7 @@
 			[FTRACE] Set and start specified trace events in order
 			to facilitate early boot debugging. The event-list is a
 			comma separated list of trace events to enable. See
-			also Documentation/trace/events.txt
+			also Documentation/trace/events.rst
 
 	trace_options=[option-list]
 			[FTRACE] Enable or disable tracer options at boot.
@@ -4333,7 +4347,7 @@
 
 			      trace_options=stacktrace
 
-			See also Documentation/trace/ftrace.txt "trace options"
+			See also Documentation/trace/ftrace.rst "trace options"
 			section.
 
 	tp_printk[FTRACE]

Documentation/admin-guide/pm/intel_pstate.rst

@@ -324,8 +324,7 @@ Global Attributes
 
 ``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
 control its functionality at the system level.  They are located in the
-``/sys/devices/system/cpu/cpufreq/intel_pstate/`` directory and affect all
-CPUs.
+``/sys/devices/system/cpu/intel_pstate/`` directory and affect all CPUs.
 
 Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
 argument is passed to the kernel in the command line.
@@ -379,6 +378,17 @@ argument is passed to the kernel in the command line.
 	but it affects the maximum possible value of per-policy P-state	limits
 	(see `Interpretation of Policy Attributes`_ below for details).
 
+``hwp_dynamic_boost``
+	This attribute is only present if ``intel_pstate`` works in the
+	`active mode with the HWP feature enabled <Active Mode With HWP_>`_ in
+	the processor.  If set (equal to 1), it causes the minimum P-state limit
+	to be increased dynamically for a short time whenever a task previously
+	waiting on I/O is selected to run on a given logical CPU (the purpose
+	of this mechanism is to improve performance).
+
+	This setting has no effect on logical CPUs whose minimum P-state limit
+	is directly set to the highest non-turbo P-state or above it.
+
 .. _status_attr:
 
 ``status``
@@ -410,7 +420,7 @@ argument is passed to the kernel in the command line.
 	That only is supported in some configurations, though (for example, if
 	the `HWP feature is enabled in the processor <Active Mode With HWP_>`_,
 	the operation mode of the driver cannot be changed), and if it is not
-	supported in the current configuration, writes to this attribute with
+	supported in the current configuration, writes to this attribute will
 	fail with an appropriate error.
 
 Interpretation of Policy Attributes

Documentation/arm/OMAP/README

@@ -5,3 +5,7 @@ KERNEL		NEW DEPENDENCIES
 v4.3+		Update is needed for custom .config files to make sure
 		CONFIG_REGULATOR_PBIAS is enabled for MMC1 to work
 		properly.
+
+v4.18+		Update is needed for custom .config files to make sure
+		CONFIG_MMC_SDHCI_OMAP is enabled for all MMC instances
+		to work in DRA7 and K2G based boards.

Documentation/block/biodoc.txt

@@ -752,18 +752,6 @@ completion of the request to the block layer. This means ending tag
 operations before calling end_that_request_last()! For an example of a user
 of these helpers, see the IDE tagged command queueing support.
 
-Certain hardware conditions may dictate a need to invalidate the block tag
-queue. For instance, on IDE any tagged request error needs to clear both
-the hardware and software block queue and enable the driver to sanely restart
-all the outstanding requests. There's a third helper to do that:
-
-	blk_queue_invalidate_tags(struct request_queue *q)
-
-	Clear the internal block tag queue and re-add all the pending requests
-	to the request queue. The driver will receive them again on the
-	next request_fn run, just like it did the first time it encountered
-	them.
-
 3.2.5.2 Tag info
 
 Some block functions exist to query current tag status or to go from a
@@ -805,8 +793,7 @@ Internally, block manages tags in the blk_queue_tag structure:
 Most of the above is simple and straight forward, however busy_list may need
 a bit of explaining. Normally we don't care too much about request ordering,
 but in the event of any barrier requests in the tag queue we need to ensure
-that requests are restarted in the order they were queue. This may happen
-if the driver needs to use blk_queue_invalidate_tags().
+that requests are restarted in the order they were queue.
 
 3.3 I/O Submission
 

Documentation/core-api/kernel-api.rst

@@ -284,7 +284,7 @@ Resources Management
 MTRR Handling
 -------------
 
-.. kernel-doc:: arch/x86/kernel/cpu/mtrr/main.c
+.. kernel-doc:: arch/x86/kernel/cpu/mtrr/mtrr.c
    :export:
 
 Security Framework

Documentation/crypto/crypto_engine.rst

@@ -8,11 +8,13 @@ The crypto engine API (CE), is a crypto queue manager.
 
 Requirement
 -----------
-You have to put at start of your tfm_ctx the struct crypto_engine_ctx
-struct your_tfm_ctx {
+You have to put at start of your tfm_ctx the struct crypto_engine_ctx::
+
+  struct your_tfm_ctx {
         struct crypto_engine_ctx enginectx;
         ...
-};
+  };
+
 Why: Since CE manage only crypto_async_request, it cannot know the underlying
 request_type and so have access only on the TFM.
 So using container_of for accessing __ctx is impossible.

Documentation/device-mapper/writecache.txt

@@ -0,0 +1,68 @@
+The writecache target caches writes on persistent memory or on SSD. It
+doesn't cache reads because reads are supposed to be cached in page cache
+in normal RAM.
+
+When the device is constructed, the first sector should be zeroed or the
+first sector should contain valid superblock from previous invocation.
+
+Constructor parameters:
+1. type of the cache device - "p" or "s"
+	p - persistent memory
+	s - SSD
+2. the underlying device that will be cached
+3. the cache device
+4. block size (4096 is recommended; the maximum block size is the page
+   size)
+5. the number of optional parameters (the parameters with an argument
+   count as two)
+	high_watermark n	(default: 50)
+		start writeback when the number of used blocks reach this
+		watermark
+	low_watermark x		(default: 45)
+		stop writeback when the number of used blocks drops below
+		this watermark
+	writeback_jobs n	(default: unlimited)
+		limit the number of blocks that are in flight during
+		writeback. Setting this value reduces writeback
+		throughput, but it may improve latency of read requests
+	autocommit_blocks n	(default: 64 for pmem, 65536 for ssd)
+		when the application writes this amount of blocks without
+		issuing the FLUSH request, the blocks are automatically
+		commited
+	autocommit_time ms	(default: 1000)
+		autocommit time in milliseconds. The data is automatically
+		commited if this time passes and no FLUSH request is
+		received
+	fua			(by default on)
+		applicable only to persistent memory - use the FUA flag
+		when writing data from persistent memory back to the
+		underlying device
+	nofua
+		applicable only to persistent memory - don't use the FUA
+		flag when writing back data and send the FLUSH request
+		afterwards
+		- some underlying devices perform better with fua, some
+		  with nofua. The user should test it
+
+Status:
+1. error indicator - 0 if there was no error, otherwise error number
+2. the number of blocks
+3. the number of free blocks
+4. the number of blocks under writeback
+
+Messages:
+	flush
+		flush the cache device. The message returns successfully
+		if the cache device was flushed without an error
+	flush_on_suspend
+		flush the cache device on next suspend. Use this message
+		when you are going to remove the cache device. The proper
+		sequence for removing the cache device is:
+		1. send the "flush_on_suspend" message
+		2. load an inactive table with a linear target that maps
+		   to the underlying device
+		3. suspend the device
+		4. ask for status and verify that there are no errors
+		5. resume the device, so that it will use the linear
+		   target
+		6. the cache device is now inactive and it can be deleted

Documentation/devicetree/bindings/arm/amlogic.txt

@@ -25,6 +25,10 @@ Boards with the Amlogic Meson8b SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,meson8b";
 
+Boards with the Amlogic Meson8m2 SoC shall have the following properties:
+  Required root node property:
+    compatible: "amlogic,meson8m2";
+
 Boards with the Amlogic Meson GXBaby SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,meson-gxbb";
@@ -54,6 +58,8 @@ Board compatible values (alphabetically, grouped by SoC):
   - "hardkernel,odroid-c1" (Meson8b)
   - "tronfy,mxq" (Meson8b)
 
+  - "tronsmart,mxiii-plus" (Meson8m2)
+
   - "amlogic,p200" (Meson gxbb)
   - "amlogic,p201" (Meson gxbb)
   - "friendlyarm,nanopi-k2" (Meson gxbb)

Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt

@@ -34,6 +34,10 @@ Raspberry Pi 3 Model B
 Required root node properties:
 compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
 
+Raspberry Pi 3 Model B+
+Required root node properties:
+compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+
 Raspberry Pi Compute Module
 Required root node properties:
 compatible = "raspberrypi,compute-module", "brcm,bcm2835";

Documentation/devicetree/bindings/arm/mediatek/mediatek,g3dsys.txt

@@ -0,0 +1,30 @@
+MediaTek g3dsys controller
+============================
+
+The MediaTek g3dsys controller provides various clocks and reset controller to
+the GPU.
+
+Required Properties:
+
+- compatible: Should be:
+	- "mediatek,mt2701-g3dsys", "syscon":
+		for MT2701 SoC
+	- "mediatek,mt7623-g3dsys", "mediatek,mt2701-g3dsys", "syscon":
+		for MT7623 SoC
+- #clock-cells: Must be 1
+- #reset-cells: Must be 1
+
+The g3dsys controller uses the common clk binding from
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+The available clocks are defined in dt-bindings/clock/mt*-clk.h.
+
+Example:
+
+g3dsys: clock-controller@13000000 {
+	compatible = "mediatek,mt7623-g3dsys",
+		     "mediatek,mt2701-g3dsys",
+		     "syscon";
+	reg = <0 0x13000000 0 0x200>;
+	#clock-cells = <1>;
+	#reset-cells = <1>;
+};

Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt

@@ -21,8 +21,6 @@ Required root node properties:
 	- "samsung,smdk5420"	- for Exynos5420-based Samsung SMDK5420 eval board.
 	- "samsung,tm2"		- for Exynos5433-based Samsung TM2 board.
 	- "samsung,tm2e"	- for Exynos5433-based Samsung TM2E board.
-	- "samsung,sd5v1"	- for Exynos5440-based Samsung board.
-	- "samsung,ssdk5440"	- for Exynos5440-based Samsung board.
 
 * Other companies Exynos SoC based
   * FriendlyARM

Documentation/devicetree/bindings/arm/shmobile.txt

@@ -21,6 +21,8 @@ SoCs:
     compatible = "renesas,r8a7744"
   - RZ/G1E (R8A77450)
     compatible = "renesas,r8a7745"
+  - RZ/G1C (R8A77470)
+    compatible = "renesas,r8a77470"
   - R-Car M1A (R8A77781)
     compatible = "renesas,r8a7778"
   - R-Car H1 (R8A77790)
@@ -45,6 +47,8 @@ SoCs:
     compatible = "renesas,r8a77970"
   - R-Car V3H (R8A77980)
     compatible = "renesas,r8a77980"
+  - R-Car E3 (R8A77990)
+    compatible = "renesas,r8a77990"
   - R-Car D3 (R8A77995)
     compatible = "renesas,r8a77995"
 
@@ -67,6 +71,8 @@ Boards:
     compatible = "renesas,draak", "renesas,r8a77995"
   - Eagle (RTP0RC77970SEB0010S)
     compatible = "renesas,eagle", "renesas,r8a77970"
+  - Ebisu (RTP0RC77990SEB0010S)
+    compatible = "renesas,ebisu", "renesas,r8a77990"
   - Genmai (RTK772100BC00000BR)
     compatible = "renesas,genmai", "renesas,r7s72100"
   - GR-Peach (X28A-M01-E/F)
@@ -78,6 +84,8 @@ Boards:
     compatible = "renesas,h3ulcb", "renesas,r8a7795"
   - Henninger
     compatible = "renesas,henninger", "renesas,r8a7791"
+  - iWave Systems RZ/G1C Single Board Computer (iW-RainboW-G23S)
+    compatible = "iwave,g23s", "renesas,r8a77470"
   - iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D)
     compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745"
   - iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM)
@@ -108,7 +116,7 @@ Boards:
     compatible = "renesas,salvator-x", "renesas,r8a7795"
   - Salvator-X (RTP0RC7796SIPB0011S)
     compatible = "renesas,salvator-x", "renesas,r8a7796"
-  - Salvator-X (RTP0RC7796SIPB0011S (M3N))
+  - Salvator-X (RTP0RC7796SIPB0011S (M3-N))
     compatible = "renesas,salvator-x", "renesas,r8a77965"
   - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S)
     compatible = "renesas,salvator-xs", "renesas,r8a7795"
@@ -124,6 +132,8 @@ Boards:
     compatible = "renesas,sk-rzg1m", "renesas,r8a7743"
   - Stout (ADAS Starterkit, Y-R-CAR-ADAS-SKH2-BOARD)
     compatible = "renesas,stout", "renesas,r8a7790"
+  - V3HSK (Y-ASK-RCAR-V3H-WS10)
+    compatible = "renesas,v3hsk", "renesas,r8a77980"
   - V3MSK (Y-ASK-RCAR-V3M-WS10)
     compatible = "renesas,v3msk", "renesas,r8a77970"
   - Wheat (RTP0RC7792ASKB0000JE)

Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt

@@ -1,18 +0,0 @@
-NVIDIA Tegra30 MC(Memory Controller)
-
-Required properties:
-- compatible : "nvidia,tegra30-mc"
-- reg : Should contain 4 register ranges(address and length); see the
-  example below. Note that the MC registers are interleaved with the
-  SMMU registers, and hence must be represented as multiple ranges.
-- interrupts : Should contain MC General interrupt.
-
-Example:
-	memory-controller {
-		compatible = "nvidia,tegra30-mc";
-		reg = <0x7000f000 0x010
-		       0x7000f03c 0x1b4
-		       0x7000f200 0x028
-		       0x7000f284 0x17c>;
-		interrupts = <0 77 0x04>;
-	};

Documentation/devicetree/bindings/bus/ti-sysc.txt

@@ -79,7 +79,11 @@ Optional properties:
 		mode as for example omap4 L4_CFG_CLKCTRL
 
 - clock-names	should contain at least "fck", and optionally also "ick"
-		depending on the SoC and the interconnect target module
+		depending on the SoC and the interconnect target module,
+		some interconnect target modules also need additional
+		optional clocks that can be specified as listed in TRM
+		for the related CLKCTRL register bits 8 to 15 such as
+		"dbclk" or "clk32k" depending on their role
 
 - ti,hwmods	optional TI interconnect module name to use legacy
 		hwmod platform data

Documentation/devicetree/bindings/clock/actions,s900-cmu.txt

@@ -0,0 +1,47 @@
+* Actions S900 Clock Management Unit (CMU)
+
+The Actions S900 clock management unit generates and supplies clock to various
+controllers within the SoC. The clock binding described here is applicable to
+S900 SoC.
+
+Required Properties:
+
+- compatible: should be "actions,s900-cmu"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- clocks: Reference to the parent clocks ("hosc", "losc")
+- #clock-cells: should be 1.
+
+Each clock is assigned an identifier, and client nodes can use this identifier
+to specify the clock which they consume.
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/actions,s900-cmu.h header and can be used in device
+tree sources.
+
+External clocks:
+
+The hosc clock used as input for the plls is generated outside the SoC. It is
+expected that it is defined using standard clock bindings as "hosc".
+
+Actions S900 CMU also requires one more clock:
+ - "losc" - internal low frequency oscillator
+
+Example: Clock Management Unit node:
+
+        cmu: clock-controller@e0160000 {
+                compatible = "actions,s900-cmu";
+                reg = <0x0 0xe0160000 0x0 0x1000>;
+                clocks = <&hosc>, <&losc>;
+                #clock-cells = <1>;
+        };
+
+Example: UART controller node that consumes clock generated by the clock
+management unit:
+
+        uart: serial@e012a000 {
+                compatible = "actions,s900-uart", "actions,owl-uart";
+                reg = <0x0 0xe012a000 0x0 0x2000>;
+                interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+                clocks = <&cmu CLK_UART5>;
+        };

Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt

@@ -9,6 +9,7 @@ Required Properties:
 	- GXBB (S905) : "amlogic,meson-gxbb-aoclkc"
 	- GXL (S905X, S905D) : "amlogic,meson-gxl-aoclkc"
 	- GXM (S912) : "amlogic,meson-gxm-aoclkc"
+	- AXG (A113D, A113X) : "amlogic,meson-axg-aoclkc"
 	followed by the common "amlogic,meson-gx-aoclkc"
 
 - #clock-cells: should be 1.

Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt

@@ -10,9 +10,6 @@ Required Properties:
 		"amlogic,gxl-clkc" for GXL and GXM SoC,
 		"amlogic,axg-clkc" for AXG SoC.
 
-- reg: physical base address of the clock controller and length of memory
-       mapped region.
-
 - #clock-cells: should be 1.
 
 Each clock is assigned an identifier and client nodes can use this identifier
@@ -20,13 +17,22 @@ to specify the clock which they consume. All available clocks are defined as
 preprocessor macros in the dt-bindings/clock/gxbb-clkc.h header and can be
 used in device tree sources.
 
+Parent node should have the following properties :
+- compatible: "syscon", "simple-mfd, and "amlogic,meson-gx-hhi-sysctrl" or
+              "amlogic,meson-axg-hhi-sysctrl"
+- reg: base address and size of the HHI system control register space.
+
 Example: Clock controller node:
 
-	clkc: clock-controller@c883c000 {
+sysctrl: system-controller@0 {
+	compatible = "amlogic,meson-gx-hhi-sysctrl", "syscon", "simple-mfd";
+	reg = <0 0 0 0x400>;
+
+	clkc: clock-controller {
 		#clock-cells = <1>;
 		compatible = "amlogic,gxbb-clkc";
-		reg = <0x0 0xc883c000 0x0 0x3db>;
 	};
+};
 
 Example: UART controller node that consumes the clock generated by the clock
   controller:

Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt

@@ -276,36 +276,38 @@ These clock IDs are defined in:
     clk_ts_500_ref	genpll2		2	BCM_SR_GENPLL2_TS_500_REF_CLK
     clk_125_nitro	genpll2		3	BCM_SR_GENPLL2_125_NITRO_CLK
     clk_chimp		genpll2		4	BCM_SR_GENPLL2_CHIMP_CLK
-    clk_nic_flash	genpll2		5	BCM_SR_GENPLL2_NIC_FLASH
+    clk_nic_flash	genpll2		5	BCM_SR_GENPLL2_NIC_FLASH_CLK
+    clk_fs		genpll2		6	BCM_SR_GENPLL2_FS_CLK
 
     genpll3		crystal		0	BCM_SR_GENPLL3
     clk_hsls		genpll3		1	BCM_SR_GENPLL3_HSLS_CLK
     clk_sdio		genpll3		2	BCM_SR_GENPLL3_SDIO_CLK
 
     genpll4		crystal		0	BCM_SR_GENPLL4
-    ccn			genpll4		1	BCM_SR_GENPLL4_CCN_CLK
+    clk_ccn		genpll4		1	BCM_SR_GENPLL4_CCN_CLK
     clk_tpiu_pll	genpll4		2	BCM_SR_GENPLL4_TPIU_PLL_CLK
-    noc_clk		genpll4		3	BCM_SR_GENPLL4_NOC_CLK
+    clk_noc		genpll4		3	BCM_SR_GENPLL4_NOC_CLK
     clk_chclk_fs4	genpll4		4	BCM_SR_GENPLL4_CHCLK_FS4_CLK
     clk_bridge_fscpu	genpll4		5	BCM_SR_GENPLL4_BRIDGE_FSCPU_CLK
 
-
     genpll5		crystal		0	BCM_SR_GENPLL5
-    fs4_hf_clk		genpll5		1	BCM_SR_GENPLL5_FS4_HF_CLK
-    crypto_ae_clk	genpll5		2	BCM_SR_GENPLL5_CRYPTO_AE_CLK
-    raid_ae_clk		genpll5		3	BCM_SR_GENPLL5_RAID_AE_CLK
+    clk_fs4_hf		genpll5		1	BCM_SR_GENPLL5_FS4_HF_CLK
+    clk_crypto_ae	genpll5		2	BCM_SR_GENPLL5_CRYPTO_AE_CLK
+    clk_raid_ae		genpll5		3	BCM_SR_GENPLL5_RAID_AE_CLK
 
     genpll6		crystal		0	BCM_SR_GENPLL6
-    48_usb		genpll6		1	BCM_SR_GENPLL6_48_USB_CLK
+    clk_48_usb		genpll6		1	BCM_SR_GENPLL6_48_USB_CLK
 
     lcpll0		crystal		0	BCM_SR_LCPLL0
     clk_sata_refp 	lcpll0		1	BCM_SR_LCPLL0_SATA_REFP_CLK
     clk_sata_refn	lcpll0		2	BCM_SR_LCPLL0_SATA_REFN_CLK
-    clk_usb_ref		lcpll0		3	BCM_SR_LCPLL0_USB_REF_CLK
-    sata_refpn		lcpll0		3	BCM_SR_LCPLL0_SATA_REFPN_CLK
+    clk_sata_350	lcpll0		3	BCM_SR_LCPLL0_SATA_350_CLK
+    clk_sata_500	lcpll0		4	BCM_SR_LCPLL0_SATA_500_CLK
 
     lcpll1		crystal		0	BCM_SR_LCPLL1
-    wan 		lcpll1		1	BCM_SR_LCPLL0_WAN_CLK
+    clk_wan		lcpll1		1	BCM_SR_LCPLL1_WAN_CLK
+    clk_usb_ref		lcpll1		2	BCM_SR_LCPLL1_USB_REF_CLK
+    clk_crmu_ts		lcpll1		3	BCM_SR_LCPLL1_CRMU_TS_CLK
 
     lcpll_pcie		crystal		0	BCM_SR_LCPLL_PCIE
-    pcie_phy_ref 	lcpll1		1	BCM_SR_LCPLL_PCIE_PHY_REF_CLK
+    clk_pcie_phy_ref	lcpll1		1	BCM_SR_LCPLL_PCIE_PHY_REF_CLK

Documentation/devicetree/bindings/clock/nuvoton,npcm750-clk.txt

@@ -0,0 +1,100 @@
+* Nuvoton NPCM7XX Clock Controller
+
+Nuvoton Poleg BMC NPCM7XX contains an integrated clock controller, which
+generates and supplies clocks to all modules within the BMC.
+
+External clocks:
+
+There are six fixed clocks that are generated outside the BMC. All clocks are of
+a known fixed value that cannot be changed. clk_refclk, clk_mcbypck and
+clk_sysbypck are inputs to the clock controller.
+clk_rg1refck, clk_rg2refck and clk_xin are external clocks suppling the
+network. They are set on the device tree, but not used by the clock module. The
+network devices use them directly.
+Example can be found below.
+
+All available clocks are defined as preprocessor macros in:
+dt-bindings/clock/nuvoton,npcm7xx-clock.h
+and can be reused as DT sources.
+
+Required Properties of clock controller:
+
+	- compatible: "nuvoton,npcm750-clk" : for clock controller of Nuvoton
+		  Poleg BMC NPCM750
+
+	- reg: physical base address of the clock controller and length of
+		memory mapped region.
+
+	- #clock-cells: should be 1.
+
+Example: Clock controller node:
+
+	clk: clock-controller@f0801000 {
+		compatible = "nuvoton,npcm750-clk";
+		#clock-cells = <1>;
+		reg = <0xf0801000 0x1000>;
+		clock-names = "refclk", "sysbypck", "mcbypck";
+		clocks = <&clk_refclk>, <&clk_sysbypck>, <&clk_mcbypck>;
+	};
+
+Example: Required external clocks for network:
+
+	/* external reference clock */
+	clk_refclk: clk-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+		clock-output-names = "refclk";
+	};
+
+	/* external reference clock for cpu. float in normal operation */
+	clk_sysbypck: clk-sysbypck {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <800000000>;
+		clock-output-names = "sysbypck";
+	};
+
+	/* external reference clock for MC. float in normal operation */
+	clk_mcbypck: clk-mcbypck {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <800000000>;
+		clock-output-names = "mcbypck";
+	};
+
+	 /* external clock signal rg1refck, supplied by the phy */
+	clk_rg1refck: clk-rg1refck {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "clk_rg1refck";
+	};
+
+	 /* external clock signal rg2refck, supplied by the phy */
+	clk_rg2refck: clk-rg2refck {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "clk_rg2refck";
+	};
+
+	clk_xin: clk-xin {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "clk_xin";
+	};
+
+
+Example: GMAC controller node that consumes two clocks: a generated clk by the
+clock controller and a fixed clock from DT (clk_rg1refck).
+
+	ethernet0: ethernet@f0802000 {
+		compatible = "snps,dwmac";
+		reg = <0xf0802000 0x2000>;
+		interrupts = <0 14 4>;
+		interrupt-names = "macirq";
+		clocks	= <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>;
+		clock-names = "stmmaceth", "clk_gmac";
+	};

Documentation/devicetree/bindings/clock/qcom,gcc.txt

@@ -17,7 +17,9 @@ Required properties :
 			"qcom,gcc-msm8974pro-ac"
 			"qcom,gcc-msm8994"
 			"qcom,gcc-msm8996"
+			"qcom,gcc-msm8998"
 			"qcom,gcc-mdm9615"
+			"qcom,gcc-sdm845"
 
 - reg : shall contain base register location and length
 - #clock-cells : shall contain 1

Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt

@@ -0,0 +1,22 @@
+Qualcomm Technologies, Inc. RPMh Clocks
+-------------------------------------------------------
+
+Resource Power Manager Hardened (RPMh) manages shared resources on
+some Qualcomm Technologies Inc. SoCs. It accepts clock requests from
+other hardware subsystems via RSC to control clocks.
+
+Required properties :
+- compatible : shall contain "qcom,sdm845-rpmh-clk"
+
+- #clock-cells : must contain 1
+
+Example :
+
+#include <dt-bindings/clock/qcom,rpmh.h>
+
+	&apps_rsc {
+		rpmhcc: clock-controller {
+			compatible = "qcom,sdm845-rpmh-clk";
+			#clock-cells = <1>;
+		};
+	};

Documentation/devicetree/bindings/clock/qcom,videocc.txt

@@ -0,0 +1,19 @@
+Qualcomm Video Clock & Reset Controller Binding
+-----------------------------------------------
+
+Required properties :
+- compatible : shall contain "qcom,sdm845-videocc"
+- reg : shall contain base register location and length
+- #clock-cells : from common clock binding, shall contain 1.
+- #power-domain-cells : from generic power domain binding, shall contain 1.
+
+Optional properties :
+- #reset-cells : from common reset binding, shall contain 1.
+
+Example:
+	videocc: clock-controller@ab00000 {
+		compatible = "qcom,sdm845-videocc";
+		reg = <0xab00000 0x10000>;
+		#clock-cells = <1>;
+		#power-domain-cells = <1>;
+	};

Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt

@@ -15,6 +15,7 @@ Required Properties:
   - compatible: Must be one of:
       - "renesas,r8a7743-cpg-mssr" for the r8a7743 SoC (RZ/G1M)
       - "renesas,r8a7745-cpg-mssr" for the r8a7745 SoC (RZ/G1E)
+      - "renesas,r8a77470-cpg-mssr" for the r8a77470 SoC (RZ/G1C)
       - "renesas,r8a7790-cpg-mssr" for the r8a7790 SoC (R-Car H2)
       - "renesas,r8a7791-cpg-mssr" for the r8a7791 SoC (R-Car M2-W)
       - "renesas,r8a7792-cpg-mssr" for the r8a7792 SoC (R-Car V2H)
@@ -25,6 +26,7 @@ Required Properties:
       - "renesas,r8a77965-cpg-mssr" for the r8a77965 SoC (R-Car M3-N)
       - "renesas,r8a77970-cpg-mssr" for the r8a77970 SoC (R-Car V3M)
       - "renesas,r8a77980-cpg-mssr" for the r8a77980 SoC (R-Car V3H)
+      - "renesas,r8a77990-cpg-mssr" for the r8a77990 SoC (R-Car E3)
       - "renesas,r8a77995-cpg-mssr" for the r8a77995 SoC (R-Car D3)
 
   - reg: Base address and length of the memory resource used by the CPG/MSSR
@@ -33,10 +35,12 @@ Required Properties:
   - clocks: References to external parent clocks, one entry for each entry in
     clock-names
   - clock-names: List of external parent clock names. Valid names are:
-      - "extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7792, r8a7793, r8a7794,
-		 r8a7795, r8a7796, r8a77965, r8a77970, r8a77980, r8a77995)
+      - "extal" (r8a7743, r8a7745, r8a77470, r8a7790, r8a7791, r8a7792,
+		 r8a7793, r8a7794, r8a7795, r8a7796, r8a77965, r8a77970,
+		 r8a77980, r8a77990, r8a77995)
       - "extalr" (r8a7795, r8a7796, r8a77965, r8a77970, r8a77980)
-      - "usb_extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7793, r8a7794)
+      - "usb_extal" (r8a7743, r8a7745, r8a77470, r8a7790, r8a7791, r8a7793,
+		     r8a7794)
 
   - #clock-cells: Must be 2
       - For CPG core clocks, the two clock specifier cells must be "CPG_CORE"

Documentation/devicetree/bindings/clock/rockchip.txt

@@ -1,77 +0,0 @@
-Device Tree Clock bindings for arch-rockchip
-
-This binding uses the common clock binding[1].
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-
-== Gate clocks ==
-
-These bindings are deprecated!
-Please use the soc specific CRU bindings instead.
-
-The gate registers form a continuos block which makes the dt node
-structure a matter of taste, as either all gates can be put into
-one gate clock spanning all registers or they can be divided into
-the 10 individual gates containing 16 clocks each.
-The code supports both approaches.
-
-Required properties:
-- compatible : "rockchip,rk2928-gate-clk"
-- reg : shall be the control register address(es) for the clock.
-- #clock-cells : from common clock binding; shall be set to 1
-- clock-output-names : the corresponding gate names that the clock controls
-- clocks : should contain the parent clock for each individual gate,
-  therefore the number of clocks elements should match the number of
-  clock-output-names
-
-Example using multiple gate clocks:
-
-		clk_gates0: gate-clk@200000d0 {
-			compatible = "rockchip,rk2928-gate-clk";
-			reg = <0x200000d0 0x4>;
-			clocks = <&dummy>, <&dummy>,
-				 <&dummy>, <&dummy>,
-				 <&dummy>, <&dummy>,
-				 <&dummy>, <&dummy>,
-				 <&dummy>, <&dummy>,
-				 <&dummy>, <&dummy>,
-				 <&dummy>, <&dummy>,
-				 <&dummy>, <&dummy>;
-
-			clock-output-names =
-				"gate_core_periph", "gate_cpu_gpll",
-				"gate_ddrphy", "gate_aclk_cpu",
-				"gate_hclk_cpu", "gate_pclk_cpu",
-				"gate_atclk_cpu", "gate_i2s0",
-				"gate_i2s0_frac", "gate_i2s1",
-				"gate_i2s1_frac", "gate_i2s2",
-				"gate_i2s2_frac", "gate_spdif",
-				"gate_spdif_frac", "gate_testclk";
-
-			#clock-cells = <1>;
-		};
-
-		clk_gates1: gate-clk@200000d4 {
-			compatible = "rockchip,rk2928-gate-clk";
-			reg = <0x200000d4 0x4>;
-			clocks = <&xin24m>, <&xin24m>,
-				 <&xin24m>, <&dummy>,
-				 <&dummy>, <&xin24m>,
-				 <&xin24m>, <&dummy>,
-				 <&xin24m>, <&dummy>,
-				 <&xin24m>, <&dummy>,
-				 <&xin24m>, <&dummy>,
-				 <&xin24m>, <&dummy>;
-
-			clock-output-names =
-				"gate_timer0", "gate_timer1",
-				"gate_timer2", "gate_jtag",
-				"gate_aclk_lcdc1_src", "gate_otgphy0",
-				"gate_otgphy1", "gate_ddr_gpll",
-				"gate_uart0", "gate_frac_uart0",
-				"gate_uart1", "gate_frac_uart1",
-				"gate_uart2", "gate_frac_uart2",
-				"gate_uart3", "gate_frac_uart3";
-
-			#clock-cells = <1>;
-		};

Documentation/devicetree/bindings/clock/st/st,clkgen.txt

@@ -31,10 +31,10 @@ This binding uses the common clock binding[1].
 Each subnode should use the binding described in [2]..[7]
 
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[3] Documentation/devicetree/bindings/clock/st,clkgen-mux.txt
-[4] Documentation/devicetree/bindings/clock/st,clkgen-pll.txt
-[7] Documentation/devicetree/bindings/clock/st,quadfs.txt
-[8] Documentation/devicetree/bindings/clock/st,flexgen.txt
+[3] Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt
+[4] Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt
+[7] Documentation/devicetree/bindings/clock/st/st,quadfs.txt
+[8] Documentation/devicetree/bindings/clock/st/st,flexgen.txt
 
 
 Required properties:

Documentation/devicetree/bindings/clock/sunxi-ccu.txt

@@ -21,6 +21,7 @@ Required properties :
 		- "allwinner,sun50i-a64-r-ccu"
 		- "allwinner,sun50i-h5-ccu"
 		- "allwinner,sun50i-h6-ccu"
+		- "allwinner,sun50i-h6-r-ccu"
 		- "nextthing,gr8-ccu"
 
 - reg: Must contain the registers base address and length
@@ -35,7 +36,7 @@ Required properties :
 For the main CCU on H6, one more clock is needed:
 - "iosc": the SoC's internal frequency oscillator
 
-For the PRCM CCUs on A83T/H3/A64, two more clocks are needed:
+For the PRCM CCUs on A83T/H3/A64/H6, two more clocks are needed:
 - "pll-periph": the SoC's peripheral PLL from the main CCU
 - "iosc": the SoC's internal frequency oscillator
 

Documentation/devicetree/bindings/clock/ti/gate.txt

@@ -10,7 +10,7 @@ will be controlled instead and the corresponding hw-ops for
 that is used.
 
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/clock/gate-clock.txt
+[2] Documentation/devicetree/bindings/clock/gpio-gate-clock.txt
 [3] Documentation/devicetree/bindings/clock/ti/clockdomain.txt
 
 Required properties:

Documentation/devicetree/bindings/clock/ti/interface.txt

@@ -9,7 +9,7 @@ companion clock finding (match corresponding functional gate
 clock) and hardware autoidle enable / disable.
 
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/clock/gate-clock.txt
+[2] Documentation/devicetree/bindings/clock/gpio-gate-clock.txt
 
 Required properties:
 - compatible : shall be one of:

Documentation/devicetree/bindings/cpufreq/cpufreq-mediatek.txt

@@ -8,7 +8,7 @@ Required properties:
 	"intermediate"	- A parent of "cpu" clock which is used as "intermediate" clock
 			  source (usually MAINPLL) when the original CPU PLL is under
 			  transition and not stable yet.
-	Please refer to Documentation/devicetree/bindings/clk/clock-bindings.txt for
+	Please refer to Documentation/devicetree/bindings/clock/clock-bindings.txt for
 	generic clock consumer properties.
 - operating-points-v2: Please refer to Documentation/devicetree/bindings/opp/opp.txt
 	for detail.

Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt

@@ -12,7 +12,7 @@ Required properties:
 - clocks:		 Phandles for clock specified in "clock-names" property
 - clock-names :		 The name of clock used by the DFI, must be
 			 "pclk_ddr_mon";
-- operating-points-v2:	 Refer to Documentation/devicetree/bindings/power/opp.txt
+- operating-points-v2:	 Refer to Documentation/devicetree/bindings/opp/opp.txt
 			 for details.
 - center-supply:	 DMC supply node.
 - status:		 Marks the node enabled/disabled.

Documentation/devicetree/bindings/display/bridge/tda998x.txt

@@ -30,7 +30,7 @@ Optional properties:
   - nxp,calib-gpios: calibration GPIO, which must correspond with the
 	gpio used for the TDA998x interrupt pin.
 
-[1] Documentation/sound/alsa/soc/DAI.txt
+[1] Documentation/sound/soc/dai.rst
 [2] include/dt-bindings/display/tda998x.h
 
 Example:

Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt

@@ -29,6 +29,7 @@ Required Properties:
 		- "renesas,dmac-r8a77965" (R-Car M3-N)
 		- "renesas,dmac-r8a77970" (R-Car V3M)
 		- "renesas,dmac-r8a77980" (R-Car V3H)
+		- "renesas,dmac-r8a77995" (R-Car D3)
 
 - reg: base address and length of the registers block for the DMAC
 

Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt

@@ -12,6 +12,8 @@ Required Properties:
 	  - "renesas,r8a7795-usb-dmac" (R-Car H3)
 	  - "renesas,r8a7796-usb-dmac" (R-Car M3-W)
 	  - "renesas,r8a77965-usb-dmac" (R-Car M3-N)
+	  - "renesas,r8a77990-usb-dmac" (R-Car E3)
+	  - "renesas,r8a77995-usb-dmac" (R-Car D3)
 - reg: base address and length of the registers block for the DMAC
 - interrupts: interrupt specifiers for the DMAC, one for each entry in
   interrupt-names.

Documentation/devicetree/bindings/firmware/qcom,scm.txt

@@ -11,9 +11,10 @@ Required properties:
  * "qcom,scm-msm8660" for MSM8660 platforms
  * "qcom,scm-msm8690" for MSM8690 platforms
  * "qcom,scm-msm8996" for MSM8996 platforms
+ * "qcom,scm-ipq4019" for IPQ4019 platforms
  * "qcom,scm" for later processors (MSM8916, APQ8084, MSM8974, etc)
 - clocks: One to three clocks may be required based on compatible.
- * No clock required for "qcom,scm-msm8996"
+ * No clock required for "qcom,scm-msm8996", "qcom,scm-ipq4019"
  * Only core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660", and "qcom,scm-msm8960"
  * Core, iface, and bus clocks required for "qcom,scm"
 - clock-names: Must contain "core" for the core clock, "iface" for the interface

Documentation/devicetree/bindings/gpio/gpio-pca953x.txt

@@ -31,10 +31,15 @@ Required properties:
 	ti,tca9554
 	onnn,pca9654
 	exar,xra1202
+ - gpio-controller: if used as gpio expander.
+ - #gpio-cells: if used as gpio expander.
+ - interrupt-controller: if to be used as interrupt expander.
+ - #interrupt-cells: if to be used as interrupt expander.
 
 Optional properties:
  - reset-gpios: GPIO specification for the RESET input. This is an
 		active low signal to the PCA953x.
+ - vcc-supply:	power supply regulator.
 
 Example:
 
@@ -47,3 +52,32 @@ Example:
 		interrupt-parent = <&gpio3>;
 		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
 	};
+
+
+Example with Interrupts:
+
+
+	gpio99: gpio@22 {
+		compatible = "nxp,pcal6524";
+		reg = <0x22>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;	/* gpio6_161 */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&vdds_1v8_main>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"hdmi-ct-hpd", "hdmi.ls-oe", "p02", "p03", "vibra", "fault2", "p06", "p07",
+			"en-usb", "en-host1", "en-host2", "chg-int", "p14", "p15", "mic-int", "en-modem",
+			"shdn-hs-amp", "chg-status+red", "green", "blue", "en-esata", "fault1", "p26", "p27";
+	};
+
+	ts3a227@3b {
+		compatible = "ti,ts3a227e";
+		reg = <0x3b>;
+		interrupt-parent = <&gpio99>;
+		interrupts = <14 IRQ_TYPE_EDGE_RISING>;
+		ti,micbias = <0>;	/* 2.1V */
+	};
+

Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt

@@ -5,6 +5,7 @@ Required Properties:
   - compatible: should contain one or more of the following:
     - "renesas,gpio-r8a7743": for R8A7743 (RZ/G1M) compatible GPIO controller.
     - "renesas,gpio-r8a7745": for R8A7745 (RZ/G1E) compatible GPIO controller.
+    - "renesas,gpio-r8a77470": for R8A77470 (RZ/G1C) compatible GPIO controller.
     - "renesas,gpio-r8a7778": for R8A7778 (R-Car M1) compatible GPIO controller.
     - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller.
     - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller.
@@ -14,7 +15,9 @@ Required Properties:
     - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller.
     - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller.
     - "renesas,gpio-r8a7796": for R8A7796 (R-Car M3-W) compatible GPIO controller.
+    - "renesas,gpio-r8a77965": for R8A77965 (R-Car M3-N) compatible GPIO controller.
     - "renesas,gpio-r8a77970": for R8A77970 (R-Car V3M) compatible GPIO controller.
+    - "renesas,gpio-r8a77990": for R8A77990 (R-Car E3) compatible GPIO controller.
     - "renesas,gpio-r8a77995": for R8A77995 (R-Car D3) compatible GPIO controller.
     - "renesas,rcar-gen1-gpio": for a generic R-Car Gen1 GPIO controller.
     - "renesas,rcar-gen2-gpio": for a generic R-Car Gen2 or RZ/G1 GPIO controller.

Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt

@@ -26,8 +26,13 @@ controller.
   the second encodes the triger flags encoded as described in
   Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 - interrupt-parent : The parent interrupt controller.
-- interrupts : The interrupt to the parent controller raised when GPIOs
-  generate the interrupts.
+- interrupts : The interrupts to the parent controller raised when GPIOs
+  generate the interrupts. If the controller provides one combined interrupt
+  for all GPIOs, specify a single interrupt. If the controller provides one
+  interrupt for each GPIO, provide a list of interrupts that correspond to each
+  of the GPIO pins. When specifying multiple interrupts, if any are unconnected,
+  use the interrupts-extended property to specify the interrupts and set the
+  interrupt controller handle for unused interrupts to 0.
 - snps,nr-gpios : The number of pins in the port, a single cell.
 - resets : Reset line for the controller.
 

Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt

@@ -34,7 +34,7 @@ Optional properties:
 - mali-supply : Phandle to regulator for the Mali device. Refer to
   Documentation/devicetree/bindings/regulator/regulator.txt for details.
 
-- operating-points-v2 : Refer to Documentation/devicetree/bindings/power/opp.txt
+- operating-points-v2 : Refer to Documentation/devicetree/bindings/opp/opp.txt
   for details.
 
 

Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt

@@ -44,7 +44,7 @@ Optional properties:
 
   - memory-region:
     Memory region to allocate from, as defined in
-    Documentation/devicetree/bindi/reserved-memory/reserved-memory.txt
+    Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
 
   - mali-supply:
     Phandle to regulator for the Mali device, as defined in

Documentation/devicetree/bindings/i2c/i2c-davinci.txt

@@ -24,7 +24,7 @@ Recommended properties :
 - clock-frequency : desired I2C bus clock frequency in Hz.
 - ti,has-pfunc: boolean; if defined, it indicates that SoC supports PFUNC
 	registers. PFUNC registers allow to switch I2C pins to function as
-	GPIOs, so they can by toggled manually.
+	GPIOs, so they can be toggled manually.
 
 Example (enbw_cmc board):
 	i2c@1c22000 {

Documentation/devicetree/bindings/i2c/i2c-rcar.txt

@@ -15,6 +15,7 @@ Required properties:
 	"renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC.
 	"renesas,i2c-r8a77965" if the device is a part of a R8A77965 SoC.
 	"renesas,i2c-r8a77970" if the device is a part of a R8A77970 SoC.
+	"renesas,i2c-r8a77980" if the device is a part of a R8A77980 SoC.
 	"renesas,i2c-r8a77995" if the device is a part of a R8A77995 SoC.
 	"renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device.
 	"renesas,rcar-gen2-i2c" for a generic R-Car Gen2 or RZ/G1 compatible

Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt

@@ -8,9 +8,7 @@ Required properties:
       (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
       (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
           inside HDMIPHY block found on several samsung SoCs
-      (d) "samsung, exynos5440-i2c", for s3c2440-like i2c used
-	   on EXYNOS5440 which does not need GPIO configuration.
-      (e) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as
+      (d) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as
 	   a host to SATA PHY controller on an internal bus.
   - reg: physical base address of the controller and length of memory mapped
     region.

Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt

@@ -7,6 +7,7 @@ Required properties:
 			- "amlogic,meson-gxbb-saradc" for GXBB
 			- "amlogic,meson-gxl-saradc" for GXL
 			- "amlogic,meson-gxm-saradc" for GXM
+			- "amlogic,meson-axg-saradc" for AXG
 		along with the generic "amlogic,meson-saradc"
 - reg:		the physical base address and length of the registers
 - interrupts:	the interrupt indicating end of sampling

Documentation/devicetree/bindings/iio/adc/mcp320x.txt

@@ -49,7 +49,7 @@ Required properties:
 Examples:
 spi_controller {
 	mcp3x0x@0 {
-		compatible = "mcp3002";
+		compatible = "microchip,mcp3002";
 		reg = <0>;
 		spi-max-frequency = <1000000>;
 		vref-supply = <&vref_reg>;

Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt

@@ -24,8 +24,11 @@ Required properties:
 - compatible: Should be one of:
   "st,stm32f4-adc-core"
   "st,stm32h7-adc-core"
+  "st,stm32mp1-adc-core"
 - reg: Offset and length of the ADC block register set.
-- interrupts: Must contain the interrupt for ADC block.
+- interrupts: One or more interrupts for ADC block. Some parts like stm32f4
+  and stm32h7 share a common ADC interrupt line. stm32mp1 has two separate
+  interrupt lines, one for each ADC within ADC block.
 - clocks: Core can use up to two clocks, depending on part used:
   - "adc" clock: for the analog circuitry, common to all ADCs.
     It's required on stm32f4.
@@ -53,6 +56,7 @@ Required properties:
 - compatible: Should be one of:
   "st,stm32f4-adc"
   "st,stm32h7-adc"
+  "st,stm32mp1-adc"
 - reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200).
 - clocks: Input clock private to this ADC instance. It's required only on
   stm32f4, that has per instance clock input for registers access.

Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt

@@ -8,14 +8,16 @@ It is mainly targeted for:
 - PDM microphones (audio digital microphone)
 
 It features up to 8 serial digital interfaces (SPI or Manchester) and
-up to 4 filters on stm32h7.
+up to 4 filters on stm32h7 or 6 filters on stm32mp1.
 
 Each child node match with a filter instance.
 
 Contents of a STM32 DFSDM root node:
 ------------------------------------
 Required properties:
-- compatible: Should be "st,stm32h7-dfsdm".
+- compatible: Should be one of:
+  "st,stm32h7-dfsdm"
+  "st,stm32mp1-dfsdm"
 - reg: Offset and length of the DFSDM block register set.
 - clocks: IP and serial interfaces clocking. Should be set according
 		to rcc clock ID and "clock-names".
@@ -45,6 +47,7 @@ Required properties:
 	"st,stm32-dfsdm-adc" for sigma delta ADCs
 	"st,stm32-dfsdm-dmic" for audio digital microphone.
 - reg: Specifies the DFSDM filter instance used.
+	Valid values are from 0 to 3 on stm32h7, 0 to 5 on stm32mp1.
 - interrupts: IRQ lines connected to each DFSDM filter instance.
 - st,adc-channels:	List of single-ended channels muxed for this ADC.
 			valid values:

Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.txt

@@ -0,0 +1,26 @@
+Current Sense Amplifier
+=======================
+
+When an io-channel measures the output voltage from a current sense
+amplifier, the interesting measurement is almost always the current
+through the sense resistor, not the voltage output. This binding
+describes such a current sense circuit.
+
+Required properties:
+- compatible : "current-sense-amplifier"
+- io-channels : Channel node of a voltage io-channel.
+- sense-resistor-micro-ohms : The sense resistance in microohms.
+
+Optional properties:
+- sense-gain-mult: Amplifier gain multiplier. The default is <1>.
+- sense-gain-div: Amplifier gain divider. The default is <1>.
+
+Example:
+
+sysi {
+	compatible = "current-sense-amplifier";
+	io-channels = <&tiadc 0>;
+
+	sense-resistor-micro-ohms = <20000>;
+	sense-gain-mul = <50>;
+};

Documentation/devicetree/bindings/iio/afe/current-sense-shunt.txt

@@ -0,0 +1,41 @@
+Current Sense Shunt
+===================
+
+When an io-channel measures the voltage over a current sense shunt,
+the interesting measurement is almost always the current through the
+shunt, not the voltage over it. This binding describes such a current
+sense circuit.
+
+Required properties:
+- compatible : "current-sense-shunt"
+- io-channels : Channel node of a voltage io-channel.
+- shunt-resistor-micro-ohms : The shunt resistance in microohms.
+
+Example:
+The system current is measured by measuring the voltage over a
+3.3 ohms shunt resistor.
+
+sysi {
+	compatible = "current-sense-shunt";
+	io-channels = <&tiadc 0>;
+
+	/* Divide the voltage by 3300000/1000000 (or 3.3) for the current. */
+	shunt-resistor-micro-ohms = <3300000>;
+};
+
+&i2c {
+	tiadc: adc@48 {
+		compatible = "ti,ads1015";
+		reg = <0x48>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 { /* IN0,IN1 differential */
+			reg = <0>;
+			ti,gain = <1>;
+			ti,datarate = <4>;
+		};
+	};
+};

Documentation/devicetree/bindings/iio/afe/voltage-divider.txt

@@ -0,0 +1,53 @@
+Voltage divider
+===============
+
+When an io-channel measures the midpoint of a voltage divider, the
+interesting voltage is often the voltage over the full resistance
+of the divider. This binding describes the voltage divider in such
+a curcuit.
+
+    Vin ----.
+            |
+         .-----.
+         |  R  |
+         '-----'
+            |
+            +---- Vout
+            |
+         .-----.
+         | Rout|
+         '-----'
+            |
+           GND
+
+Required properties:
+- compatible : "voltage-divider"
+- io-channels : Channel node of a voltage io-channel measuring Vout.
+- output-ohms : Resistance Rout over which the output voltage is measured.
+	        See full-ohms.
+- full-ohms : Resistance R + Rout for the full divider. The io-channel
+	      is scaled by the Rout / (R + Rout) quotient.
+
+Example:
+The system voltage is circa 12V, but divided down with a 22/222
+voltage divider (R = 200 Ohms, Rout = 22 Ohms) and fed to an ADC.
+
+sysv {
+	compatible = "voltage-divider";
+	io-channels = <&maxadc 1>;
+
+	/* Scale the system voltage by 22/222 to fit the ADC range. */
+	output-ohms = <22>;
+	full-ohms = <222>; /* 200 + 22 */
+};
+
+&spi {
+	maxadc: adc@0 {
+		compatible = "maxim,max1027";
+		reg = <0>;
+		#io-channel-cells = <1>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <15 IRQ_TYPE_EDGE_RISING>;
+		spi-max-frequency = <1000000>;
+	};
+};

Documentation/devicetree/bindings/iio/dac/ltc2632.txt

@@ -12,12 +12,26 @@ Required properties:
 Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
 apply. In particular, "reg" and "spi-max-frequency" properties must be given.
 
+Optional properties:
+	- vref-supply: Phandle to the external reference voltage supply. This should
+	  only be set if there is an external reference voltage connected to the VREF
+	  pin. If the property is not set the internal reference is used.
+
 Example:
 
+	vref: regulator-vref {
+		compatible = "regulator-fixed";
+		regulator-name = "vref-ltc2632";
+		regulator-min-microvolt = <1250000>;
+		regulator-max-microvolt = <1250000>;
+		regulator-always-on;
+	};
+
 	spi_master {
 		dac: ltc2632@0 {
 			compatible = "lltc,ltc2632-l12";
 			reg = <0>; /* CS0 */
 			spi-max-frequency = <1000000>;
+			vref-supply = <&vref>; /* optional */
 		};
 	};

Documentation/devicetree/bindings/iio/dac/ti,dac5571.txt

@@ -0,0 +1,24 @@
+* Texas Instruments DAC5571 Family
+
+Required properties:
+ - compatible: Should contain
+    "ti,dac5571"
+    "ti,dac6571"
+    "ti,dac7571"
+    "ti,dac5574"
+    "ti,dac6574"
+    "ti,dac7574"
+    "ti,dac5573"
+    "ti,dac6573"
+    "ti,dac7573"
+ - reg: Should contain the DAC I2C address
+
+Optional properties:
+ - vref-supply: The regulator supply for DAC reference voltage
+
+Example:
+dac@0 {
+	compatible = "ti,dac5571";
+	reg = <0x4C>;
+	vref-supply = <&vdd_supply>;
+};

Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt

@@ -8,10 +8,16 @@ Required properties:
  		"invensense,mpu6500"
 		"invensense,mpu9150"
 		"invensense,mpu9250"
+		"invensense,mpu9255"
 		"invensense,icm20608"
  - reg : the I2C address of the sensor
  - interrupt-parent : should be the phandle for the interrupt controller
- - interrupts : interrupt mapping for GPIO IRQ
+ - interrupts: interrupt mapping for IRQ. It should be configured with flags
+   IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or
+   IRQ_TYPE_EDGE_FALLING.
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client node
+  bindings.
 
 Optional properties:
  - mount-matrix: an optional 3x3 mounting rotation matrix
@@ -24,7 +30,7 @@ Example:
 		compatible = "invensense,mpu6050";
 		reg = <0x68>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <18 1>;
+		interrupts = <18 IRQ_TYPE_EDGE_RISING>;
 		mount-matrix = "-0.984807753012208",  /* x0 */
 		               "0",                   /* y0 */
 		               "-0.173648177666930",  /* z0 */
@@ -41,7 +47,7 @@ Example:
 		compatible = "invensense,mpu9250";
 		reg = <0x68>;
 		interrupt-parent = <&gpio3>;
-		interrupts = <21 1>;
+		interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;
 		i2c-gate {
 			#address-cells = <1>;
 			#size-cells = <0>;

Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt

@@ -6,6 +6,7 @@ Required properties:
   "st,lsm6ds3h"
   "st,lsm6dsl"
   "st,lsm6dsm"
+  "st,ism330dlc"
 - reg: i2c address of the sensor / spi cs line
 
 Optional properties:

Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt

@@ -1,10 +1,13 @@
-* Texas Instruments LMP91000 potentiostat
+* Texas Instruments LMP91000 series of potentiostats
 
-http://www.ti.com/lit/ds/symlink/lmp91000.pdf
+LMP91000: http://www.ti.com/lit/ds/symlink/lmp91000.pdf
+LMP91002: http://www.ti.com/lit/ds/symlink/lmp91002.pdf
 
 Required properties:
 
-  - compatible: should be "ti,lmp91000"
+  - compatible: should be one of the following:
+                 "ti,lmp91000"
+                 "ti,lmp91002"
   - reg: the I2C address of the device
   - io-channels: the phandle of the iio provider
 

Documentation/devicetree/bindings/input/mtk-pmic-keys.txt

@@ -0,0 +1,43 @@
+MediaTek MT6397/MT6323 PMIC Keys Device Driver
+
+There are two key functions provided by MT6397/MT6323 PMIC, pwrkey
+and homekey. The key functions are defined as the subnode of the function
+node provided by MT6397/MT6323 PMIC that is being defined as one kind
+of Muti-Function Device (MFD)
+
+For MT6397/MT6323 MFD bindings see:
+Documentation/devicetree/bindings/mfd/mt6397.txt
+
+Required properties:
+- compatible: "mediatek,mt6397-keys" or "mediatek,mt6323-keys"
+- linux,keycodes: See Documentation/devicetree/bindings/input/keys.txt
+
+Optional Properties:
+- wakeup-source: See Documentation/devicetree/bindings/power/wakeup-source.txt
+- mediatek,long-press-mode: Long press key shutdown setting, 1 for
+	pwrkey only, 2 for pwrkey/homekey together, others for disabled.
+- power-off-time-sec: See Documentation/devicetree/bindings/input/keys.txt
+
+Example:
+
+	pmic: mt6397 {
+		compatible = "mediatek,mt6397";
+
+		...
+
+		mt6397keys: mt6397keys {
+			compatible = "mediatek,mt6397-keys";
+			mediatek,long-press-mode = <1>;
+			power-off-time-sec = <0>;
+
+			power {
+				linux,keycodes = <116>;
+				wakeup-source;
+			};
+
+			home {
+				linux,keycodes = <114>;
+			};
+		};
+
+	};

Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt

@@ -12,7 +12,7 @@ Additional documentation for F11 can be found at:
 http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf
 
 Optional Touch Properties:
-Description in Documentation/devicetree/bindings/input/touch
+Description in Documentation/devicetree/bindings/input/touchscreen
 - touchscreen-inverted-x
 - touchscreen-inverted-y
 - touchscreen-swapped-x-y

Documentation/devicetree/bindings/input/rotary-encoder.txt

@@ -28,7 +28,7 @@ Deprecated properties:
   This property is deprecated. Instead, a 'steps-per-period ' value should
   be used, such as "rotary-encoder,steps-per-period = <2>".
 
-See Documentation/input/rotary-encoder.txt for more information.
+See Documentation/input/devices/rotary-encoder.rst for more information.
 
 Example:
 

Documentation/devicetree/bindings/input/sprd,sc27xx-vibra.txt

@@ -0,0 +1,23 @@
+Spreadtrum SC27xx PMIC Vibrator
+
+Required properties:
+- compatible: should be "sprd,sc2731-vibrator".
+- reg: address of vibrator control register.
+
+Example :
+
+	sc2731_pmic: pmic@0 {
+		compatible = "sprd,sc2731";
+		reg = <0>;
+		spi-max-frequency = <26000000>;
+		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vibrator@eb4 {
+			compatible = "sprd,sc2731-vibrator";
+			reg = <0xeb4>;
+		};
+	};

Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt

@@ -17,6 +17,10 @@ Optional properties:
                "pwms" property (see PWM binding[0])
   - enable-gpios: contains a single GPIO specifier for the GPIO which enables
                   and disables the backlight (see GPIO binding[1])
+  - post-pwm-on-delay-ms: Delay in ms between setting an initial (non-zero) PWM
+                          and enabling the backlight using GPIO.
+  - pwm-off-delay-ms: Delay in ms between disabling the backlight using GPIO
+                      and setting PWM value to 0.
 
 [0]: Documentation/devicetree/bindings/pwm/pwm.txt
 [1]: Documentation/devicetree/bindings/gpio/gpio.txt
@@ -32,4 +36,6 @@ Example:
 
 		power-supply = <&vdd_bl_reg>;
 		enable-gpios = <&gpio 58 0>;
+		post-pwm-on-delay-ms = <10>;
+		pwm-off-delay-ms = <10>;
 	};

Documentation/devicetree/bindings/leds/backlight/zii,rave-sp-backlight.txt

@@ -0,0 +1,23 @@
+Zodiac Inflight Innovations RAVE Supervisory Processor Backlight Bindings
+
+RAVE SP backlight device is a "MFD cell" device corresponding to
+backlight functionality of RAVE Supervisory Processor. It is expected
+that its Device Tree node is specified as a child of the node
+corresponding to the parent RAVE SP device (as documented in
+Documentation/devicetree/bindings/mfd/zii,rave-sp.txt)
+
+Required properties:
+
+- compatible: Should be "zii,rave-sp-backlight"
+
+Example:
+
+	rave-sp {
+		compatible = "zii,rave-sp-rdu1";
+		current-speed = <38400>;
+
+		backlight {
+			compatible = "zii,rave-sp-backlight";
+		};
+	}
+

Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt

@@ -28,7 +28,7 @@ See: Documentation/devicetree/bindings/clock/clock-bindings.txt
 - pinctrl-names	: a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num)
 		   must be defined for each tsin child node.
 - pinctrl-0	: phandle referencing pin configuration for this tsin configuration
-See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
 
 
 Required properties (tsin (child) node):

Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.txt

@@ -6,11 +6,21 @@ Required properties:
   example below. Note that the MC registers are interleaved with the
   GART registers, and hence must be represented as multiple ranges.
 - interrupts : Should contain MC General interrupt.
+- #reset-cells : Should be 1. This cell represents memory client module ID.
+  The assignments may be found in header file <dt-bindings/memory/tegra20-mc.h>
+  or in the TRM documentation.
 
 Example:
-	memory-controller@7000f000 {
+	mc: memory-controller@7000f000 {
 		compatible = "nvidia,tegra20-mc";
 		reg = <0x7000f000 0x024
 		       0x7000f03c 0x3c4>;
 		interrupts = <0 77 0x04>;
+		#reset-cells = <1>;
+	};
+
+	video-codec@6001a000 {
+		compatible = "nvidia,tegra20-vde";
+		...
+		resets = <&mc TEGRA20_MC_RESET_VDE>;
 	};

Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt

@@ -12,6 +12,9 @@ Required properties:
 - clock-names: Must include the following entries:
   - mc: the module's clock input
 - interrupts: The interrupt outputs from the controller.
+- #reset-cells : Should be 1. This cell represents memory client module ID.
+  The assignments may be found in header file <dt-bindings/memory/tegra30-mc.h>
+  or in the TRM documentation.
 
 Required properties for Tegra30, Tegra114, Tegra124, Tegra132 and Tegra210:
 - #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines
@@ -72,12 +75,14 @@ Example SoC include file:
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 
 		#iommu-cells = <1>;
+		#reset-cells = <1>;
 	};
 
 	sdhci@700b0000 {
 		compatible = "nvidia,tegra124-sdhci";
 		...
 		iommus = <&mc TEGRA_SWGROUP_SDMMC1A>;
+		resets = <&mc TEGRA124_MC_RESET_SDMMC1>;
 	};
 };
 

Documentation/devicetree/bindings/mfd/arizona.txt

@@ -50,7 +50,7 @@ Required properties:
 
 Optional properties:
 
-  - wlf,reset : GPIO specifier for the GPIO controlling /RESET
+  - reset-gpios : GPIO specifier for the GPIO controlling /RESET
 
   - clocks: Should reference the clocks supplied on MCLK1 and MCLK2
   - clock-names: Should contains two strings:
@@ -70,6 +70,10 @@ Optional properties:
     Documentation/devicetree/bindings/regulator/regulator.txt
     (wm5102, wm5110, wm8280, wm8997, wm8998, wm1814)
 
+Deprecated properties:
+
+  - wlf,reset : GPIO specifier for the GPIO controlling /RESET
+
 Also see child specific device properties:
   Regulator - ../regulator/arizona-regulator.txt
   Extcon    - ../extcon/extcon-arizona.txt

Documentation/devicetree/bindings/mfd/as3722.txt

@@ -46,7 +46,7 @@ is required:
 	Following properties are require if pin control setting is required
 	at boot.
 	- pinctrl-names: A pinctrl state named "default" be defined, using the
-		bindings in pinctrl/pinctrl-binding.txt.
+		bindings in pinctrl/pinctrl-bindings.txt.
 	- pinctrl[0...n]: Properties to contain the phandle that refer to
 		different nodes of pin control settings. These nodes represents
 		the pin control setting of state 0 to state n. Each of these

Documentation/devicetree/bindings/mfd/axp20x.txt

@@ -43,7 +43,7 @@ Optional properties:
 			  regulator to drive the OTG VBus, rather then
 			  as an input pin which signals whether the
 			  board is driving OTG VBus or not.
-			  (axp221 / axp223 / axp813 only)
+			  (axp221 / axp223 / axp803/ axp813 only)
 
 - x-powers,master-mode: Boolean (axp806 only). Set this when the PMIC is
 			wired for master mode. The default is slave mode.
@@ -132,6 +132,7 @@ FLDO2		: LDO		: fldoin-supply		: shared supply
 LDO_IO0		: LDO		: ips-supply		: GPIO 0
 LDO_IO1		: LDO		: ips-supply		: GPIO 1
 RTC_LDO		: LDO		: ips-supply		: always on
+DRIVEVBUS	: Enable output	: drivevbus-supply	: external regulator
 
 AXP806 regulators, type, and corresponding input supply names:
 

Documentation/devicetree/bindings/mfd/bd9571mwv.txt

@@ -25,6 +25,25 @@ Required properties:
 			    Each child node is defined using the standard
 			    binding for regulators.
 
+Optional properties:
+  - rohm,ddr-backup-power : Value to use for DDR-Backup Power (default 0).
+			    This is a bitmask that specifies which DDR power
+			    rails need to be kept powered when backup mode is
+			    entered, for system suspend:
+			      - bit 0: DDR0
+			      - bit 1: DDR1
+			      - bit 2: DDR0C
+			      - bit 3: DDR1C
+			    These bits match the KEEPON_DDR* bits in the
+			    documentation for the "BKUP Mode Cnt" register.
+  - rohm,rstbmode-level: The RSTB signal is configured for level mode, to
+			 accommodate a toggle power switch (the RSTBMODE pin is
+			 strapped low).
+  - rohm,rstbmode-pulse: The RSTB signal is configured for pulse mode, to
+			 accommodate a momentary power switch (the RSTBMODE pin
+			 is strapped high).
+			 The two properties above are mutually exclusive.
+
 Example:
 
 	pmic: pmic@30 {
@@ -36,6 +55,8 @@ Example:
 		#interrupt-cells = <2>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		rohm,ddr-backup-power = <0xf>;
+		rohm,rstbmode-pulse;
 
 		regulators {
 			dvfs: dvfs {

Documentation/devicetree/bindings/mfd/da9063.txt

@@ -1,4 +1,4 @@
-* Dialog DA9063 Power Management Integrated Circuit (PMIC)
+* Dialog DA9063/DA9063L Power Management Integrated Circuit (PMIC)
 
 DA9093 consists of a large and varied group of sub-devices (I2C Only):
 
@@ -6,14 +6,14 @@ Device                   Supply Names    Description
 ------                   ------------    -----------
 da9063-regulator        :               : LDOs & BUCKs
 da9063-onkey            :               : On Key
-da9063-rtc              :               : Real-Time Clock
+da9063-rtc              :               : Real-Time Clock (DA9063 only)
 da9063-watchdog         :               : Watchdog
 
 ======
 
 Required properties:
 
-- compatible : Should be "dlg,da9063"
+- compatible : Should be "dlg,da9063" or "dlg,da9063l"
 - reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
   modified to match the chip's OTP settings).
 - interrupt-parent : Specifies the reference to the interrupt controller for
@@ -23,8 +23,8 @@ Required properties:
 
 Sub-nodes:
 
-- regulators : This node defines the settings for the LDOs and BUCKs. The
-  DA9063 regulators are bound using their names listed below:
+- regulators : This node defines the settings for the LDOs and BUCKs.
+  The DA9063(L) regulators are bound using their names listed below:
 
     bcore1    : BUCK CORE1
     bcore2    : BUCK CORE2
@@ -32,16 +32,16 @@ Sub-nodes:
     bmem      : BUCK MEM
     bio       : BUCK IO
     bperi     : BUCK PERI
-    ldo1      : LDO_1
-    ldo2      : LDO_2
+    ldo1      : LDO_1	(DA9063 only)
+    ldo2      : LDO_2	(DA9063 only)
     ldo3      : LDO_3
-    ldo4      : LDO_4
-    ldo5      : LDO_5
-    ldo6      : LDO_6
+    ldo4      : LDO_4	(DA9063 only)
+    ldo5      : LDO_5	(DA9063 only)
+    ldo6      : LDO_6	(DA9063 only)
     ldo7      : LDO_7
     ldo8      : LDO_8
     ldo9      : LDO_9
-    ldo10     : LDO_10
+    ldo10     : LDO_10	(DA9063 only)
     ldo11     : LDO_11
 
   The component follows the standard regulator framework and the bindings
@@ -49,8 +49,9 @@ Sub-nodes:
   Documentation/devicetree/bindings/regulator/regulator.txt
 
 - rtc : This node defines settings for the Real-Time Clock associated with
-  the DA9063. There are currently no entries in this binding, however
-  compatible = "dlg,da9063-rtc" should be added if a node is created.
+  the DA9063 only. The RTC is not present in DA9063L. There are currently
+  no entries in this binding, however compatible = "dlg,da9063-rtc" should
+  be added if a node is created.
 
 - onkey : This node defines the OnKey settings for controlling the key
   functionality of the device. The node should contain the compatible property
@@ -65,8 +66,9 @@ Sub-nodes:
     and KEY_SLEEP.
 
 - watchdog : This node defines settings for the Watchdog timer associated
-  with the DA9063. There are currently no entries in this binding, however
-  compatible = "dlg,da9063-watchdog" should be added if a node is created.
+  with the DA9063 and DA9063L. There are currently no entries in this
+  binding, however compatible = "dlg,da9063-watchdog" should be added
+  if a node is created.
 
 
 Example:

Documentation/devicetree/bindings/mfd/motorola-cpcap.txt

@@ -12,6 +12,30 @@ Required properties:
 - spi-max-frequency	: Typically set to 3000000
 - spi-cs-high		: SPI chip select direction
 
+Optional subnodes:
+
+The sub-functions of CPCAP get their own node with their own compatible values,
+which are described in the following files:
+
+- ../power/supply/cpcap-battery.txt
+- ../power/supply/cpcap-charger.txt
+- ../regulator/cpcap-regulator.txt
+- ../phy/phy-cpcap-usb.txt
+- ../input/cpcap-pwrbutton.txt
+- ../rtc/cpcap-rtc.txt
+- ../leds/leds-cpcap.txt
+- ../iio/adc/cpcap-adc.txt
+
+The only exception is the audio codec. Instead of a compatible value its
+node must be named "audio-codec".
+
+Required properties for the audio-codec subnode:
+
+- #sound-dai-cells = <1>;
+
+The audio-codec provides two DAIs. The first one is connected to the
+Stereo HiFi DAC and the second one is connected to the Voice DAC.
+
 Example:
 
 &mcspi1 {
@@ -26,6 +50,24 @@ Example:
 		#size-cells = <0>;
 		spi-max-frequency = <3000000>;
 		spi-cs-high;
+
+		audio-codec {
+			#sound-dai-cells = <1>;
+
+			/* HiFi */
+			port@0 {
+				endpoint {
+					remote-endpoint = <&cpu_dai1>;
+				};
+			};
+
+			/* Voice */
+			port@1 {
+				endpoint {
+					remote-endpoint = <&cpu_dai2>;
+				};
+			};
+		};
 	};
 };
 

Documentation/devicetree/bindings/mfd/mt6397.txt

@@ -7,11 +7,12 @@ MT6397/MT6323 is a multifunction device with the following sub modules:
 - GPIO
 - Clock
 - LED
+- Keys
 
 It is interfaced to host controller using SPI interface by a proprietary hardware
 called PMIC wrapper or pwrap. MT6397/MT6323 MFD is a child device of pwrap.
 See the following for pwarp node definitions:
-Documentation/devicetree/bindings/soc/pwrap.txt
+Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
 
 This document describes the binding for MFD device and its sub module.
 
@@ -40,6 +41,11 @@ Optional subnodes:
 		- compatible: "mediatek,mt6323-led"
 	see Documentation/devicetree/bindings/leds/leds-mt6323.txt
 
+- keys
+	Required properties:
+		- compatible: "mediatek,mt6397-keys" or "mediatek,mt6323-keys"
+	see Documentation/devicetree/bindings/input/mtk-pmic-keys.txt
+
 Example:
 	pwrap: pwrap@1000f000 {
 		compatible = "mediatek,mt8135-pwrap";

Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt

@@ -29,6 +29,9 @@ Required properties:
                    "qcom,pm8916",
                    "qcom,pm8004",
                    "qcom,pm8909",
+                   "qcom,pm8998",
+                   "qcom,pmi8998",
+                   "qcom,pm8005",
                    or generalized "qcom,spmi-pmic".
 - reg:             Specifies the SPMI USID slave address for this device.
                    For more information see:

Documentation/devicetree/bindings/mfd/stm32-timers.txt

@@ -19,6 +19,11 @@ Required parameters:
 Optional parameters:
 - resets:		Phandle to the parent reset controller.
 			See ../reset/st,stm32-rcc.txt
+- dmas:			List of phandle to dma channels that can be used for
+			this timer instance. There may be up to 7 dma channels.
+- dma-names:		List of dma names. Must match 'dmas' property. Valid
+			names are: "ch1", "ch2", "ch3", "ch4", "up", "trig",
+			"com".
 
 Optional subnodes:
 - pwm:			See ../pwm/pwm-stm32.txt
@@ -44,3 +49,18 @@ Example:
 			reg = <0>;
 		};
 	};
+
+Example with all dmas:
+	timer@40010000 {
+		...
+		dmas = <&dmamux1 11 0x400 0x0>,
+		       <&dmamux1 12 0x400 0x0>,
+		       <&dmamux1 13 0x400 0x0>,
+		       <&dmamux1 14 0x400 0x0>,
+		       <&dmamux1 15 0x400 0x0>,
+		       <&dmamux1 16 0x400 0x0>,
+		       <&dmamux1 17 0x400 0x0>;
+		dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig", "com";
+		...
+		child nodes...
+	};

Documentation/devicetree/bindings/mfd/sun6i-prcm.txt

@@ -8,8 +8,8 @@ Required properties:
  - reg: The PRCM registers range
 
 The prcm node may contain several subdevices definitions:
- - see Documentation/devicetree/clk/sunxi.txt for clock devices
- - see Documentation/devicetree/reset/allwinner,sunxi-clock-reset.txt for reset
+ - see Documentation/devicetree/bindings/clock/sunxi.txt for clock devices
+ - see Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt for reset
    controller devices
 
 

Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt

@@ -62,7 +62,7 @@ Required properties for a slot (Deprecated - Recommend to use one slot per host)
   rest of the gpios (depending on the bus-width property) are the data lines in
   no particular order. The format of the gpio specifier depends on the gpio
   controller.
-(Deprecated - Refer to Documentation/devicetree/binding/pinctrl/samsung-pinctrl.txt)
+(Deprecated - Refer to Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt)
 
 Example:
 

Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt

@@ -12,7 +12,7 @@ Required properties:
           See: Documentation/devicetree/bindings/clock/clock-bindings.txt
 - pinctrl-names: A pinctrl state names "default" must be defined.
 - pinctrl-0: Phandle referencing pin configuration of the SDHCI controller.
-             See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+             See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
 
 Example:
 

Documentation/devicetree/bindings/mmc/sdhci-st.txt

@@ -20,7 +20,7 @@ Required properties:
 
 - pinctrl-names:	A pinctrl state names "default" must be defined.
 - pinctrl-0:		Phandle referencing pin configuration of the sd/emmc controller.
-			See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+			See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
 
 - reg:			This must provide the host controller base address and it can also
 			contain the FlashSS Top register for TX/RX delay used by the driver

Documentation/devicetree/bindings/mtd/gpmi-nand.txt

@@ -47,6 +47,11 @@ Optional properties:
                        partitions written from Linux with this feature
                        turned on may not be accessible by the BootROM
                        code.
+  - nand-ecc-strength: integer representing the number of bits to correct
+                       per ECC step. Needs to be a multiple of 2.
+  - nand-ecc-step-size: integer representing the number of data bytes
+                       that are covered by a single ECC step. The driver
+                       supports 512 and 1024.
 
 The device tree may optionally contain sub-nodes describing partitions of the
 address space. See partition.txt for more detail.

Documentation/devicetree/bindings/mtd/mtk-nand.txt

@@ -48,14 +48,19 @@ Optional:
 - nand-on-flash-bbt:	Store BBT on NAND Flash.
 - nand-ecc-mode:	the NAND ecc mode (check driver for supported modes)
 - nand-ecc-step-size:	Number of data bytes covered by a single ECC step.
-			valid values: 512 and 1024.
+			valid values:
+			512 and 1024 on mt2701 and mt2712.
+			512 only on mt7622.
 			1024 is recommended for large page NANDs.
 - nand-ecc-strength:	Number of bits to correct per ECC step.
-			The valid values that the controller supports are: 4, 6,
-			8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44,
-			48, 52, 56, 60.
+			The valid values that each controller supports:
+			mt2701: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
+				32, 36, 40, 44, 48, 52, 56, 60.
+			mt2712: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
+				32, 36, 40, 44, 48, 52, 56, 60, 68, 72, 80.
+			mt7622: 4, 6, 8, 10, 12, 14, 16.
 			The strength should be calculated as follows:
-			E = (S - F) * 8 / 14
+			E = (S - F) * 8 / B
 			S = O / (P / Q)
 				E :	nand-ecc-strength.
 				S :	spare size per sector.
@@ -64,6 +69,15 @@ Optional:
 				O :	oob size.
 				P :	page size.
 				Q :	nand-ecc-step-size.
+				B :	number of parity bits needed to correct
+					1 bitflip.
+					According to MTK NAND controller design,
+					this number depends on max ecc step size
+					that MTK NAND controller supports.
+					If max ecc step size supported is 1024,
+					then it should be always 14. And if max
+					ecc step size is 512, then it should be
+					always 13.
 			If the result does not match any one of the listed
 			choices above, please select the smaller valid value from
 			the list.

Documentation/devicetree/bindings/mtd/partition.txt

@@ -14,7 +14,7 @@ method is used for a given flash device. To describe the method there should be
 a subnode of the flash device that is named 'partitions'. It must have a
 'compatible' property, which is used to identify the method to use.
 
-We currently only document a binding for fixed layouts.
+Available bindings are listed in the "partitions" subdirectory.
 
 
 Fixed Partitions

Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.txt

@@ -0,0 +1,42 @@
+Broadcom BCM47xx Partitions
+===========================
+
+Broadcom is one of hardware manufacturers providing SoCs (BCM47xx) used in
+home routers. Their BCM947xx boards using CFE bootloader have several partitions
+without any on-flash partition table. On some devices their sizes and/or
+meanings can also vary so fixed partitioning can't be used.
+
+Discovering partitions on these devices is possible thanks to having a special
+header and/or magic signature at the beginning of each of them. They are also
+block aligned which is important for determinig a size.
+
+Most of partitions use ASCII text based magic for determining a type. More
+complex partitions (like TRX with its HDR0 magic) may include extra header
+containing some details, including a length.
+
+A list of supported partitions includes:
+1) Bootloader with Broadcom's CFE (Common Firmware Environment)
+2) NVRAM with configuration/calibration data
+3) Device manufacturer's data with some default values (e.g. SSIDs)
+4) TRX firmware container which can hold up to 4 subpartitions
+5) Backup TRX firmware used after failed upgrade
+
+As mentioned earlier, role of some partitions may depend on extra configuration.
+For example both: main firmware and backup firmware use the same TRX format with
+the same header. To distinguish currently used firmware a CFE's environment
+variable "bootpartition" is used.
+
+
+Devices using Broadcom partitions described above should should have flash node
+with a subnode named "partitions" using following properties:
+
+Required properties:
+- compatible : (required) must be "brcm,bcm947xx-cfe-partitions"
+
+Example:
+
+flash@0 {
+	partitions {
+		compatible = "brcm,bcm947xx-cfe-partitions";
+	};
+};

Documentation/devicetree/bindings/mtd/sunxi-nand.txt

@@ -22,8 +22,6 @@ Optional properties:
 - reset : phandle + reset specifier pair
 - reset-names : must contain "ahb"
 - allwinner,rb : shall contain the native Ready/Busy ids.
- or
-- rb-gpios : shall contain the gpios used as R/B pins.
 - nand-ecc-mode : one of the supported ECC modes ("hw", "soft", "soft_bch" or
 		  "none")
 

Documentation/devicetree/bindings/net/dsa/ksz.txt

@@ -6,7 +6,7 @@ Required properties:
 - compatible: For external switch chips, compatible string must be exactly one
   of: "microchip,ksz9477"
 
-See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required and optional properties.
 
 Examples:

Documentation/devicetree/bindings/net/dsa/mt7530.txt

@@ -31,7 +31,7 @@ Required properties for the child nodes within ports container:
 - phy-mode: String, must be either "trgmii" or "rgmii" for port labeled
 	 "cpu".
 
-See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required, optional properties and how the integrated switch subnodes must
 be specified.
 

Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt

@@ -4,6 +4,7 @@ Required properties:
 - compatible: Should be one of the following:
   "allwinner,sun4i-a10-sid"
   "allwinner,sun7i-a20-sid"
+  "allwinner,sun8i-a83t-sid"
   "allwinner,sun8i-h3-sid"
   "allwinner,sun50i-a64-sid"
 

Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt

@@ -18,7 +18,7 @@ Optional properties:
 Data cells:
 
 Data cells are child nodes of eerpom node, bindings for which are
-documented in Documentation/bindings/nvmem/nvmem.txt
+documented in Documentation/devicetree/bindings/nvmem/nvmem.txt
 
 Example:
 

Documentation/devicetree/bindings/pci/hisilicon-pcie.txt

@@ -3,7 +3,7 @@ HiSilicon Hip05 and Hip06 PCIe host bridge DT description
 HiSilicon PCIe host controller is based on the Synopsys DesignWare PCI core.
 It shares common functions with the PCIe DesignWare core driver and inherits
 common properties defined in
-Documentation/devicetree/bindings/pci/designware-pci.txt.
+Documentation/devicetree/bindings/pci/designware-pcie.txt.
 
 Additional properties are described here:
 

Documentation/devicetree/bindings/pci/kirin-pcie.txt

@@ -3,7 +3,7 @@ HiSilicon Kirin SoCs PCIe host DT description
 Kirin PCIe host controller is based on the Synopsys DesignWare PCI core.
 It shares common functions with the PCIe DesignWare core driver and
 inherits common properties defined in
-Documentation/devicetree/bindings/pci/designware-pci.txt.
+Documentation/devicetree/bindings/pci/designware-pcie.txt.
 
 Additional properties are described here:
 

Documentation/devicetree/bindings/pci/pci-keystone.txt

@@ -3,9 +3,9 @@ TI Keystone PCIe interface
 Keystone PCI host Controller is based on the Synopsys DesignWare PCI
 hardware version 3.65.  It shares common functions with the PCIe DesignWare
 core driver and inherits common properties defined in
-Documentation/devicetree/bindings/pci/designware-pci.txt
+Documentation/devicetree/bindings/pci/designware-pcie.txt
 
-Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt
+Please refer to Documentation/devicetree/bindings/pci/designware-pcie.txt
 for the details of DesignWare DT bindings.  Additional properties are
 described here as well as properties that are not applicable.
 

Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt

@@ -11,9 +11,9 @@ Optional Pinmux properties:
 --------------------------
 Following properties are required if default setting of pins are required
 at boot.
-- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>.
+- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>.
 - pinctrl[0...n]: Properties to contain the phandle for pinctrl states per
-		<pinctrl-binding.txt>.
+		<pinctrl-bindings.txt>.
 
 The pin configurations are defined as child of the pinctrl states node. Each
 sub-node have following properties: