V4L/DVB: staging/lirc: add lirc_sir driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

drivers/staging/lirc/lirc_sir.c

@@ -0,0 +1,1282 @@
+/*
+ * LIRC SIR driver, (C) 2000 Milan Pikula <www@fornax.sk>
+ *
+ * lirc_sir - Device driver for use with SIR (serial infra red)
+ * mode of IrDA on many notebooks.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ *
+ * 2000/09/16 Frank Przybylski <mail@frankprzybylski.de> :
+ *  added timeout and relaxed pulse detection, removed gap bug
+ *
+ * 2000/12/15 Christoph Bartelmus <lirc@bartelmus.de> :
+ *   added support for Tekram Irmate 210 (sending does not work yet,
+ *   kind of disappointing that nobody was able to implement that
+ *   before),
+ *   major clean-up
+ *
+ * 2001/02/27 Christoph Bartelmus <lirc@bartelmus.de> :
+ *   added support for StrongARM SA1100 embedded microprocessor
+ *   parts cut'n'pasted from sa1100_ir.c (C) 2000 Russell King
+ */
+
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/fs.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/serial_reg.h>
+#include <linux/time.h>
+#include <linux/string.h>
+#include <linux/types.h>
+#include <linux/wait.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/poll.h>
+#include <asm/system.h>
+#include <linux/io.h>
+#include <asm/irq.h>
+#include <linux/fcntl.h>
+#ifdef LIRC_ON_SA1100
+#include <asm/hardware.h>
+#ifdef CONFIG_SA1100_COLLIE
+#include <asm/arch/tc35143.h>
+#include <asm/ucb1200.h>
+#endif
+#endif
+
+#include <linux/timer.h>
+
+#include <media/lirc.h>
+#include <media/lirc_dev.h>
+
+/* SECTION: Definitions */
+
+/*** Tekram dongle ***/
+#ifdef LIRC_SIR_TEKRAM
+/* stolen from kernel source */
+/* definitions for Tekram dongle */
+#define TEKRAM_115200 0x00
+#define TEKRAM_57600  0x01
+#define TEKRAM_38400  0x02
+#define TEKRAM_19200  0x03
+#define TEKRAM_9600   0x04
+#define TEKRAM_2400   0x08
+
+#define TEKRAM_PW 0x10 /* Pulse select bit */
+
+/* 10bit * 1s/115200bit in milliseconds = 87ms*/
+#define TIME_CONST (10000000ul/115200ul)
+
+#endif
+
+#ifdef LIRC_SIR_ACTISYS_ACT200L
+static void init_act200(void);
+#elif defined(LIRC_SIR_ACTISYS_ACT220L)
+static void init_act220(void);
+#endif
+
+/*** SA1100 ***/
+#ifdef LIRC_ON_SA1100
+struct sa1100_ser2_registers {
+	/* HSSP control register */
+	unsigned char hscr0;
+	/* UART registers */
+	unsigned char utcr0;
+	unsigned char utcr1;
+	unsigned char utcr2;
+	unsigned char utcr3;
+	unsigned char utcr4;
+	unsigned char utdr;
+	unsigned char utsr0;
+	unsigned char utsr1;
+} sr;
+
+static int irq = IRQ_Ser2ICP;
+
+#define LIRC_ON_SA1100_TRANSMITTER_LATENCY 0
+
+/* pulse/space ratio of 50/50 */
+static unsigned long pulse_width = (13-LIRC_ON_SA1100_TRANSMITTER_LATENCY);
+/* 1000000/freq-pulse_width */
+static unsigned long space_width = (13-LIRC_ON_SA1100_TRANSMITTER_LATENCY);
+static unsigned int freq = 38000;      /* modulation frequency */
+static unsigned int duty_cycle = 50;   /* duty cycle of 50% */
+
+#endif
+
+#define RBUF_LEN 1024
+#define WBUF_LEN 1024
+
+#define LIRC_DRIVER_NAME "lirc_sir"
+
+#define PULSE '['
+
+#ifndef LIRC_SIR_TEKRAM
+/* 9bit * 1s/115200bit in milli seconds = 78.125ms*/
+#define TIME_CONST (9000000ul/115200ul)
+#endif
+
+
+/* timeout for sequences in jiffies (=5/100s), must be longer than TIME_CONST */
+#define SIR_TIMEOUT	(HZ*5/100)
+
+#ifndef LIRC_ON_SA1100
+#ifndef LIRC_IRQ
+#define LIRC_IRQ 4
+#endif
+#ifndef LIRC_PORT
+/* for external dongles, default to com1 */
+#if defined(LIRC_SIR_ACTISYS_ACT200L) || \
+    defined(LIRC_SIR_ACTISYS_ACT220L) || \
+    defined(LIRC_SIR_TEKRAM)
+#define LIRC_PORT 0x3f8
+#else
+/* onboard sir ports are typically com3 */
+#define LIRC_PORT 0x3e8
+#endif
+#endif
+
+static int io = LIRC_PORT;
+static int irq = LIRC_IRQ;
+static int threshold = 3;
+#endif
+
+static DEFINE_SPINLOCK(timer_lock);
+static struct timer_list timerlist;
+/* time of last signal change detected */
+static struct timeval last_tv = {0, 0};
+/* time of last UART data ready interrupt */
+static struct timeval last_intr_tv = {0, 0};
+static int last_value;
+
+static DECLARE_WAIT_QUEUE_HEAD(lirc_read_queue);
+
+static DEFINE_SPINLOCK(hardware_lock);
+
+static int rx_buf[RBUF_LEN];
+static unsigned int rx_tail, rx_head;
+
+static int debug;
+#define dprintk(fmt, args...)						\
+	do {								\
+		if (debug)						\
+			printk(KERN_DEBUG LIRC_DRIVER_NAME ": "		\
+				fmt, ## args);				\
+	} while (0)
+
+/* SECTION: Prototypes */
+
+/* Communication with user-space */
+static unsigned int lirc_poll(struct file *file, poll_table *wait);
+static ssize_t lirc_read(struct file *file, char *buf, size_t count,
+		loff_t *ppos);
+static ssize_t lirc_write(struct file *file, const char *buf, size_t n,
+		loff_t *pos);
+static long lirc_ioctl(struct file *filep, unsigned int cmd, unsigned long arg);
+static void add_read_queue(int flag, unsigned long val);
+static int init_chrdev(void);
+static void drop_chrdev(void);
+/* Hardware */
+static irqreturn_t sir_interrupt(int irq, void *dev_id);
+static void send_space(unsigned long len);
+static void send_pulse(unsigned long len);
+static int init_hardware(void);
+static void drop_hardware(void);
+/* Initialisation */
+static int init_port(void);
+static void drop_port(void);
+
+#ifdef LIRC_ON_SA1100
+static void on(void)
+{
+	PPSR |= PPC_TXD2;
+}
+
+static void off(void)
+{
+	PPSR &= ~PPC_TXD2;
+}
+#else
+static inline unsigned int sinp(int offset)
+{
+	return inb(io + offset);
+}
+
+static inline void soutp(int offset, int value)
+{
+	outb(value, io + offset);
+}
+#endif
+
+#ifndef MAX_UDELAY_MS
+#define MAX_UDELAY_US 5000
+#else
+#define MAX_UDELAY_US (MAX_UDELAY_MS*1000)
+#endif
+
+static void safe_udelay(unsigned long usecs)
+{
+	while (usecs > MAX_UDELAY_US) {
+		udelay(MAX_UDELAY_US);
+		usecs -= MAX_UDELAY_US;
+	}
+	udelay(usecs);
+}
+
+/* SECTION: Communication with user-space */
+
+static unsigned int lirc_poll(struct file *file, poll_table *wait)
+{
+	poll_wait(file, &lirc_read_queue, wait);
+	if (rx_head != rx_tail)
+		return POLLIN | POLLRDNORM;
+	return 0;
+}
+
+static ssize_t lirc_read(struct file *file, char *buf, size_t count,
+		loff_t *ppos)
+{
+	int n = 0;
+	int retval = 0;
+	DECLARE_WAITQUEUE(wait, current);
+
+	if (count % sizeof(int))
+		return -EINVAL;
+
+	add_wait_queue(&lirc_read_queue, &wait);
+	set_current_state(TASK_INTERRUPTIBLE);
+	while (n < count) {
+		if (rx_head != rx_tail) {
+			if (copy_to_user((void *) buf + n,
+					(void *) (rx_buf + rx_head),
+					sizeof(int))) {
+				retval = -EFAULT;
+				break;
+			}
+			rx_head = (rx_head + 1) & (RBUF_LEN - 1);
+			n += sizeof(int);
+		} else {
+			if (file->f_flags & O_NONBLOCK) {
+				retval = -EAGAIN;
+				break;
+			}
+			if (signal_pending(current)) {
+				retval = -ERESTARTSYS;
+				break;
+			}
+			schedule();
+			set_current_state(TASK_INTERRUPTIBLE);
+		}
+	}
+	remove_wait_queue(&lirc_read_queue, &wait);
+	set_current_state(TASK_RUNNING);
+	return n ? n : retval;
+}
+static ssize_t lirc_write(struct file *file, const char *buf, size_t n,
+				loff_t *pos)
+{
+	unsigned long flags;
+	int i, count;
+	int *tx_buf;
+
+	count = n / sizeof(int);
+	if (n % sizeof(int) || count % 2 == 0)
+		return -EINVAL;
+	tx_buf = memdup_user(buf, n);
+	if (IS_ERR(tx_buf))
+		return PTR_ERR(tx_buf);
+	i = 0;
+#ifdef LIRC_ON_SA1100
+	/* disable receiver */
+	Ser2UTCR3 = 0;
+#endif
+	local_irq_save(flags);
+	while (1) {
+		if (i >= count)
+			break;
+		if (tx_buf[i])
+			send_pulse(tx_buf[i]);
+		i++;
+		if (i >= count)
+			break;
+		if (tx_buf[i])
+			send_space(tx_buf[i]);
+		i++;
+	}
+	local_irq_restore(flags);
+#ifdef LIRC_ON_SA1100
+	off();
+	udelay(1000); /* wait 1ms for IR diode to recover */
+	Ser2UTCR3 = 0;
+	/* clear status register to prevent unwanted interrupts */
+	Ser2UTSR0 &= (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
+	/* enable receiver */
+	Ser2UTCR3 = UTCR3_RXE|UTCR3_RIE;
+#endif
+	return count;
+}
+
+static long lirc_ioctl(struct file *filep, unsigned int cmd, unsigned long arg)
+{
+	int retval = 0;
+	unsigned long value = 0;
+#ifdef LIRC_ON_SA1100
+	unsigned int ivalue;
+
+	if (cmd == LIRC_GET_FEATURES)
+		value = LIRC_CAN_SEND_PULSE |
+			LIRC_CAN_SET_SEND_DUTY_CYCLE |
+			LIRC_CAN_SET_SEND_CARRIER |
+			LIRC_CAN_REC_MODE2;
+	else if (cmd == LIRC_GET_SEND_MODE)
+		value = LIRC_MODE_PULSE;
+	else if (cmd == LIRC_GET_REC_MODE)
+		value = LIRC_MODE_MODE2;
+#else
+	if (cmd == LIRC_GET_FEATURES)
+		value = LIRC_CAN_SEND_PULSE | LIRC_CAN_REC_MODE2;
+	else if (cmd == LIRC_GET_SEND_MODE)
+		value = LIRC_MODE_PULSE;
+	else if (cmd == LIRC_GET_REC_MODE)
+		value = LIRC_MODE_MODE2;
+#endif
+
+	switch (cmd) {
+	case LIRC_GET_FEATURES:
+	case LIRC_GET_SEND_MODE:
+	case LIRC_GET_REC_MODE:
+		retval = put_user(value, (unsigned long *) arg);
+		break;
+
+	case LIRC_SET_SEND_MODE:
+	case LIRC_SET_REC_MODE:
+		retval = get_user(value, (unsigned long *) arg);
+		break;
+#ifdef LIRC_ON_SA1100
+	case LIRC_SET_SEND_DUTY_CYCLE:
+		retval = get_user(ivalue, (unsigned int *) arg);
+		if (retval)
+			return retval;
+		if (ivalue <= 0 || ivalue > 100)
+			return -EINVAL;
+		/* (ivalue/100)*(1000000/freq) */
+		duty_cycle = ivalue;
+		pulse_width = (unsigned long) duty_cycle*10000/freq;
+		space_width = (unsigned long) 1000000L/freq-pulse_width;
+		if (pulse_width >= LIRC_ON_SA1100_TRANSMITTER_LATENCY)
+			pulse_width -= LIRC_ON_SA1100_TRANSMITTER_LATENCY;
+		if (space_width >= LIRC_ON_SA1100_TRANSMITTER_LATENCY)
+			space_width -= LIRC_ON_SA1100_TRANSMITTER_LATENCY;
+		break;
+	case LIRC_SET_SEND_CARRIER:
+		retval = get_user(ivalue, (unsigned int *) arg);
+		if (retval)
+			return retval;
+		if (ivalue > 500000 || ivalue < 20000)
+			return -EINVAL;
+		freq = ivalue;
+		pulse_width = (unsigned long) duty_cycle*10000/freq;
+		space_width = (unsigned long) 1000000L/freq-pulse_width;
+		if (pulse_width >= LIRC_ON_SA1100_TRANSMITTER_LATENCY)
+			pulse_width -= LIRC_ON_SA1100_TRANSMITTER_LATENCY;
+		if (space_width >= LIRC_ON_SA1100_TRANSMITTER_LATENCY)
+			space_width -= LIRC_ON_SA1100_TRANSMITTER_LATENCY;
+		break;
+#endif
+	default:
+		retval = -ENOIOCTLCMD;
+
+	}
+
+	if (retval)
+		return retval;
+	if (cmd == LIRC_SET_REC_MODE) {
+		if (value != LIRC_MODE_MODE2)
+			retval = -ENOSYS;
+	} else if (cmd == LIRC_SET_SEND_MODE) {
+		if (value != LIRC_MODE_PULSE)
+			retval = -ENOSYS;
+	}
+
+	return retval;
+}
+
+static void add_read_queue(int flag, unsigned long val)
+{
+	unsigned int new_rx_tail;
+	int newval;
+
+	dprintk("add flag %d with val %lu\n", flag, val);
+
+	newval = val & PULSE_MASK;
+
+	/*
+	 * statistically, pulses are ~TIME_CONST/2 too long. we could
+	 * maybe make this more exact, but this is good enough
+	 */
+	if (flag) {
+		/* pulse */
+		if (newval > TIME_CONST/2)
+			newval -= TIME_CONST/2;
+		else /* should not ever happen */
+			newval = 1;
+		newval |= PULSE_BIT;
+	} else {
+		newval += TIME_CONST/2;
+	}
+	new_rx_tail = (rx_tail + 1) & (RBUF_LEN - 1);
+	if (new_rx_tail == rx_head) {
+		dprintk("Buffer overrun.\n");
+		return;
+	}
+	rx_buf[rx_tail] = newval;
+	rx_tail = new_rx_tail;
+	wake_up_interruptible(&lirc_read_queue);
+}
+
+static struct file_operations lirc_fops = {
+	.owner		= THIS_MODULE,
+	.read		= lirc_read,
+	.write		= lirc_write,
+	.poll		= lirc_poll,
+	.unlocked_ioctl	= lirc_ioctl,
+	.open		= lirc_dev_fop_open,
+	.release	= lirc_dev_fop_close,
+};
+
+static int set_use_inc(void *data)
+{
+       return 0;
+}
+
+static void set_use_dec(void *data)
+{
+}
+
+static struct lirc_driver driver = {
+       .name		= LIRC_DRIVER_NAME,
+       .minor		= -1,
+       .code_length	= 1,
+       .sample_rate	= 0,
+       .data		= NULL,
+       .add_to_buf	= NULL,
+       .set_use_inc	= set_use_inc,
+       .set_use_dec	= set_use_dec,
+       .fops		= &lirc_fops,
+       .dev		= NULL,
+       .owner		= THIS_MODULE,
+};
+
+
+static int init_chrdev(void)
+{
+	driver.minor = lirc_register_driver(&driver);
+	if (driver.minor < 0) {
+		printk(KERN_ERR LIRC_DRIVER_NAME ": init_chrdev() failed.\n");
+		return -EIO;
+	}
+	return 0;
+}
+
+static void drop_chrdev(void)
+{
+	lirc_unregister_driver(driver.minor);
+}
+
+/* SECTION: Hardware */
+static long delta(struct timeval *tv1, struct timeval *tv2)
+{
+	unsigned long deltv;
+
+	deltv = tv2->tv_sec - tv1->tv_sec;
+	if (deltv > 15)
+		deltv = 0xFFFFFF;
+	else
+		deltv = deltv*1000000 +
+			tv2->tv_usec -
+			tv1->tv_usec;
+	return deltv;
+}
+
+static void sir_timeout(unsigned long data)
+{
+	/*
+	 * if last received signal was a pulse, but receiving stopped
+	 * within the 9 bit frame, we need to finish this pulse and
+	 * simulate a signal change to from pulse to space. Otherwise
+	 * upper layers will receive two sequences next time.
+	 */
+
+	unsigned long flags;
+	unsigned long pulse_end;
+
+	/* avoid interference with interrupt */
+	spin_lock_irqsave(&timer_lock, flags);
+	if (last_value) {
+#ifndef LIRC_ON_SA1100
+		/* clear unread bits in UART and restart */
+		outb(UART_FCR_CLEAR_RCVR, io + UART_FCR);
+#endif
+		/* determine 'virtual' pulse end: */
+		pulse_end = delta(&last_tv, &last_intr_tv);
+		dprintk("timeout add %d for %lu usec\n", last_value, pulse_end);
+		add_read_queue(last_value, pulse_end);
+		last_value = 0;
+		last_tv = last_intr_tv;
+	}
+	spin_unlock_irqrestore(&timer_lock, flags);
+}
+
+static irqreturn_t sir_interrupt(int irq, void *dev_id)
+{
+	unsigned char data;
+	struct timeval curr_tv;
+	static unsigned long deltv;
+#ifdef LIRC_ON_SA1100
+	int status;
+	static int n;
+
+	status = Ser2UTSR0;
+	/*
+	 * Deal with any receive errors first.  The bytes in error may be
+	 * the only bytes in the receive FIFO, so we do this first.
+	 */
+	while (status & UTSR0_EIF) {
+		int bstat;
+
+		if (debug) {
+			dprintk("EIF\n");
+			bstat = Ser2UTSR1;
+
+			if (bstat & UTSR1_FRE)
+				dprintk("frame error\n");
+			if (bstat & UTSR1_ROR)
+				dprintk("receive fifo overrun\n");
+			if (bstat & UTSR1_PRE)
+				dprintk("parity error\n");
+		}
+
+		bstat = Ser2UTDR;
+		n++;
+		status = Ser2UTSR0;
+	}
+
+	if (status & (UTSR0_RFS | UTSR0_RID)) {
+		do_gettimeofday(&curr_tv);
+		deltv = delta(&last_tv, &curr_tv);
+		do {
+			data = Ser2UTDR;
+			dprintk("%d data: %u\n", n, (unsigned int) data);
+			n++;
+		} while (status & UTSR0_RID && /* do not empty fifo in order to
+						* get UTSR0_RID in any case */
+		      Ser2UTSR1 & UTSR1_RNE); /* data ready */
+
+		if (status&UTSR0_RID) {
+			add_read_queue(0 , deltv - n * TIME_CONST); /*space*/
+			add_read_queue(1, n * TIME_CONST); /*pulse*/
+			n = 0;
+			last_tv = curr_tv;
+		}
+	}
+
+	if (status & UTSR0_TFS)
+		printk(KERN_ERR "transmit fifo not full, shouldn't happen\n");
+
+	/* We must clear certain bits. */
+	status &= (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
+	if (status)
+		Ser2UTSR0 = status;
+#else
+	unsigned long deltintrtv;
+	unsigned long flags;
+	int iir, lsr;
+
+	while ((iir = inb(io + UART_IIR) & UART_IIR_ID)) {
+		switch (iir&UART_IIR_ID) { /* FIXME toto treba preriedit */
+		case UART_IIR_MSI:
+			(void) inb(io + UART_MSR);
+			break;
+		case UART_IIR_RLSI:
+			(void) inb(io + UART_LSR);
+			break;
+		case UART_IIR_THRI:
+#if 0
+			if (lsr & UART_LSR_THRE) /* FIFO is empty */
+				outb(data, io + UART_TX)
+#endif
+			break;
+		case UART_IIR_RDI:
+			/* avoid interference with timer */
+			spin_lock_irqsave(&timer_lock, flags);
+			do {
+				del_timer(&timerlist);
+				data = inb(io + UART_RX);
+				do_gettimeofday(&curr_tv);
+				deltv = delta(&last_tv, &curr_tv);
+				deltintrtv = delta(&last_intr_tv, &curr_tv);
+				dprintk("t %lu, d %d\n", deltintrtv, (int)data);
+				/*
+				 * if nothing came in last X cycles,
+				 * it was gap
+				 */
+				if (deltintrtv > TIME_CONST * threshold) {
+					if (last_value) {
+						dprintk("GAP\n");
+						/* simulate signal change */
+						add_read_queue(last_value,
+							       deltv -
+							       deltintrtv);
+						last_value = 0;
+						last_tv.tv_sec =
+							last_intr_tv.tv_sec;
+						last_tv.tv_usec =
+							last_intr_tv.tv_usec;
+						deltv = deltintrtv;
+					}
+				}
+				data = 1;
+				if (data ^ last_value) {
+					/*
+					 * deltintrtv > 2*TIME_CONST, remember?
+					 * the other case is timeout
+					 */
+					add_read_queue(last_value,
+						       deltv-TIME_CONST);
+					last_value = data;
+					last_tv = curr_tv;
+					if (last_tv.tv_usec >= TIME_CONST) {
+						last_tv.tv_usec -= TIME_CONST;
+					} else {
+						last_tv.tv_sec--;
+						last_tv.tv_usec += 1000000 -
+							TIME_CONST;
+					}
+				}
+				last_intr_tv = curr_tv;
+				if (data) {
+					/*
+					 * start timer for end of
+					 * sequence detection
+					 */
+					timerlist.expires = jiffies +
+								SIR_TIMEOUT;
+					add_timer(&timerlist);
+				}
+
+				lsr = inb(io + UART_LSR);
+			} while (lsr & UART_LSR_DR); /* data ready */
+			spin_unlock_irqrestore(&timer_lock, flags);
+			break;
+		default:
+			break;
+		}
+	}
+#endif
+	return IRQ_RETVAL(IRQ_HANDLED);
+}
+
+#ifdef LIRC_ON_SA1100
+static void send_pulse(unsigned long length)
+{
+	unsigned long k, delay;
+	int flag;
+
+	if (length == 0)
+		return;
+	/*
+	 * this won't give us the carrier frequency we really want
+	 * due to integer arithmetic, but we can accept this inaccuracy
+	 */
+
+	for (k = flag = 0; k < length; k += delay, flag = !flag) {
+		if (flag) {
+			off();
+			delay = space_width;
+		} else {
+			on();
+			delay = pulse_width;
+		}
+		safe_udelay(delay);
+	}
+	off();
+}
+
+static void send_space(unsigned long length)
+{
+	if (length == 0)
+		return;
+	off();
+	safe_udelay(length);
+}
+#else
+static void send_space(unsigned long len)
+{
+	safe_udelay(len);
+}
+
+static void send_pulse(unsigned long len)
+{
+	long bytes_out = len / TIME_CONST;
+	long time_left;
+
+	time_left = (long)len - (long)bytes_out * (long)TIME_CONST;
+	if (bytes_out == 0) {
+		bytes_out++;
+		time_left = 0;
+	}
+	while (bytes_out--) {
+		outb(PULSE, io + UART_TX);
+		/* FIXME treba seriozne cakanie z char/serial.c */
+		while (!(inb(io + UART_LSR) & UART_LSR_THRE))
+			;
+	}
+#if 0
+	if (time_left > 0)
+		safe_udelay(time_left);
+#endif
+}
+#endif
+
+#ifdef CONFIG_SA1100_COLLIE
+static int sa1100_irda_set_power_collie(int state)
+{
+	if (state) {
+		/*
+		 *  0 - off
+		 *  1 - short range, lowest power
+		 *  2 - medium range, medium power
+		 *  3 - maximum range, high power
+		 */
+		ucb1200_set_io_direction(TC35143_GPIO_IR_ON,
+					 TC35143_IODIR_OUTPUT);
+		ucb1200_set_io(TC35143_GPIO_IR_ON, TC35143_IODAT_LOW);
+		udelay(100);
+	} else {
+		/* OFF */
+		ucb1200_set_io_direction(TC35143_GPIO_IR_ON,
+					 TC35143_IODIR_OUTPUT);
+		ucb1200_set_io(TC35143_GPIO_IR_ON, TC35143_IODAT_HIGH);
+	}
+	return 0;
+}
+#endif
+
+static int init_hardware(void)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&hardware_lock, flags);
+	/* reset UART */
+#ifdef LIRC_ON_SA1100
+#ifdef CONFIG_SA1100_BITSY
+	if (machine_is_bitsy()) {
+		printk(KERN_INFO "Power on IR module\n");
+		set_bitsy_egpio(EGPIO_BITSY_IR_ON);
+	}
+#endif
+#ifdef CONFIG_SA1100_COLLIE
+	sa1100_irda_set_power_collie(3);	/* power on */
+#endif
+	sr.hscr0 = Ser2HSCR0;
+
+	sr.utcr0 = Ser2UTCR0;
+	sr.utcr1 = Ser2UTCR1;
+	sr.utcr2 = Ser2UTCR2;
+	sr.utcr3 = Ser2UTCR3;
+	sr.utcr4 = Ser2UTCR4;
+
+	sr.utdr = Ser2UTDR;
+	sr.utsr0 = Ser2UTSR0;
+	sr.utsr1 = Ser2UTSR1;
+
+	/* configure GPIO */
+	/* output */
+	PPDR |= PPC_TXD2;
+	PSDR |= PPC_TXD2;
+	/* set output to 0 */
+	off();
+
+	/* Enable HP-SIR modulation, and ensure that the port is disabled. */
+	Ser2UTCR3 = 0;
+	Ser2HSCR0 = sr.hscr0 & (~HSCR0_HSSP);
+
+	/* clear status register to prevent unwanted interrupts */
+	Ser2UTSR0 &= (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
+
+	/* 7N1 */
+	Ser2UTCR0 = UTCR0_1StpBit|UTCR0_7BitData;
+	/* 115200 */
+	Ser2UTCR1 = 0;
+	Ser2UTCR2 = 1;
+	/* use HPSIR, 1.6 usec pulses */
+	Ser2UTCR4 = UTCR4_HPSIR|UTCR4_Z1_6us;
+
+	/* enable receiver, receive fifo interrupt */
+	Ser2UTCR3 = UTCR3_RXE|UTCR3_RIE;
+
+	/* clear status register to prevent unwanted interrupts */
+	Ser2UTSR0 &= (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
+
+#elif defined(LIRC_SIR_TEKRAM)
+	/* disable FIFO */
+	soutp(UART_FCR,
+	      UART_FCR_CLEAR_RCVR|
+	      UART_FCR_CLEAR_XMIT|
+	      UART_FCR_TRIGGER_1);
+
+	/* Set DLAB 0. */
+	soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
+
+	/* First of all, disable all interrupts */
+	soutp(UART_IER, sinp(UART_IER) &
+	      (~(UART_IER_MSI|UART_IER_RLSI|UART_IER_THRI|UART_IER_RDI)));
+
+	/* Set DLAB 1. */
+	soutp(UART_LCR, sinp(UART_LCR) | UART_LCR_DLAB);
+
+	/* Set divisor to 12 => 9600 Baud */
+	soutp(UART_DLM, 0);
+	soutp(UART_DLL, 12);
+
+	/* Set DLAB 0. */
+	soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
+
+	/* power supply */
+	soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+	safe_udelay(50*1000);
+
+	/* -DTR low -> reset PIC */
+	soutp(UART_MCR, UART_MCR_RTS|UART_MCR_OUT2);
+	udelay(1*1000);
+
+	soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+	udelay(100);
+
+
+	/* -RTS low -> send control byte */
+	soutp(UART_MCR, UART_MCR_DTR|UART_MCR_OUT2);
+	udelay(7);
+	soutp(UART_TX, TEKRAM_115200|TEKRAM_PW);
+
+	/* one byte takes ~1042 usec to transmit at 9600,8N1 */
+	udelay(1500);
+
+	/* back to normal operation */
+	soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+	udelay(50);
+
+	udelay(1500);
+
+	/* read previous control byte */
+	printk(KERN_INFO LIRC_DRIVER_NAME
+	       ": 0x%02x\n", sinp(UART_RX));
+
+	/* Set DLAB 1. */
+	soutp(UART_LCR, sinp(UART_LCR) | UART_LCR_DLAB);
+
+	/* Set divisor to 1 => 115200 Baud */
+	soutp(UART_DLM, 0);
+	soutp(UART_DLL, 1);
+
+	/* Set DLAB 0, 8 Bit */
+	soutp(UART_LCR, UART_LCR_WLEN8);
+	/* enable interrupts */
+	soutp(UART_IER, sinp(UART_IER)|UART_IER_RDI);
+#else
+	outb(0, io + UART_MCR);
+	outb(0, io + UART_IER);
+	/* init UART */
+	/* set DLAB, speed = 115200 */
+	outb(UART_LCR_DLAB | UART_LCR_WLEN7, io + UART_LCR);
+	outb(1, io + UART_DLL); outb(0, io + UART_DLM);
+	/* 7N1+start = 9 bits at 115200 ~ 3 bits at 44000 */
+	outb(UART_LCR_WLEN7, io + UART_LCR);
+	/* FIFO operation */
+	outb(UART_FCR_ENABLE_FIFO, io + UART_FCR);
+	/* interrupts */
+	/* outb(UART_IER_RLSI|UART_IER_RDI|UART_IER_THRI, io + UART_IER); */
+	outb(UART_IER_RDI, io + UART_IER);
+	/* turn on UART */
+	outb(UART_MCR_DTR|UART_MCR_RTS|UART_MCR_OUT2, io + UART_MCR);
+#ifdef LIRC_SIR_ACTISYS_ACT200L
+	init_act200();
+#elif defined(LIRC_SIR_ACTISYS_ACT220L)
+	init_act220();
+#endif
+#endif
+	spin_unlock_irqrestore(&hardware_lock, flags);
+	return 0;
+}
+
+static void drop_hardware(void)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&hardware_lock, flags);
+
+#ifdef LIRC_ON_SA1100
+	Ser2UTCR3 = 0;
+
+	Ser2UTCR0 = sr.utcr0;
+	Ser2UTCR1 = sr.utcr1;
+	Ser2UTCR2 = sr.utcr2;
+	Ser2UTCR4 = sr.utcr4;
+	Ser2UTCR3 = sr.utcr3;
+
+	Ser2HSCR0 = sr.hscr0;
+#ifdef CONFIG_SA1100_BITSY
+	if (machine_is_bitsy())
+		clr_bitsy_egpio(EGPIO_BITSY_IR_ON);
+#endif
+#ifdef CONFIG_SA1100_COLLIE
+	sa1100_irda_set_power_collie(0);	/* power off */
+#endif
+#else
+	/* turn off interrupts */
+	outb(0, io + UART_IER);
+#endif
+	spin_unlock_irqrestore(&hardware_lock, flags);
+}
+
+/* SECTION: Initialisation */
+
+static int init_port(void)
+{
+	int retval;
+
+	/* get I/O port access and IRQ line */
+#ifndef LIRC_ON_SA1100
+	if (request_region(io, 8, LIRC_DRIVER_NAME) == NULL) {
+		printk(KERN_ERR LIRC_DRIVER_NAME
+		       ": i/o port 0x%.4x already in use.\n", io);
+		return -EBUSY;
+	}
+#endif
+	retval = request_irq(irq, sir_interrupt, IRQF_DISABLED,
+			     LIRC_DRIVER_NAME, NULL);
+	if (retval < 0) {
+#               ifndef LIRC_ON_SA1100
+		release_region(io, 8);
+#               endif
+		printk(KERN_ERR LIRC_DRIVER_NAME
+			": IRQ %d already in use.\n",
+			irq);
+		return retval;
+	}
+#ifndef LIRC_ON_SA1100
+	printk(KERN_INFO LIRC_DRIVER_NAME
+		": I/O port 0x%.4x, IRQ %d.\n",
+		io, irq);
+#endif
+
+	init_timer(&timerlist);
+	timerlist.function = sir_timeout;
+	timerlist.data = 0xabadcafe;
+
+	return 0;
+}
+
+static void drop_port(void)
+{
+	free_irq(irq, NULL);
+	del_timer_sync(&timerlist);
+#ifndef LIRC_ON_SA1100
+	release_region(io, 8);
+#endif
+}
+
+#ifdef LIRC_SIR_ACTISYS_ACT200L
+/* Crystal/Cirrus CS8130 IR transceiver, used in Actisys Act200L dongle */
+/* some code borrowed from Linux IRDA driver */
+
+/* Register 0: Control register #1 */
+#define ACT200L_REG0    0x00
+#define ACT200L_TXEN    0x01 /* Enable transmitter */
+#define ACT200L_RXEN    0x02 /* Enable receiver */
+#define ACT200L_ECHO    0x08 /* Echo control chars */
+
+/* Register 1: Control register #2 */
+#define ACT200L_REG1    0x10
+#define ACT200L_LODB    0x01 /* Load new baud rate count value */
+#define ACT200L_WIDE    0x04 /* Expand the maximum allowable pulse */
+
+/* Register 3: Transmit mode register #2 */
+#define ACT200L_REG3    0x30
+#define ACT200L_B0      0x01 /* DataBits, 0=6, 1=7, 2=8, 3=9(8P)  */
+#define ACT200L_B1      0x02 /* DataBits, 0=6, 1=7, 2=8, 3=9(8P)  */
+#define ACT200L_CHSY    0x04 /* StartBit Synced 0=bittime, 1=startbit */
+
+/* Register 4: Output Power register */
+#define ACT200L_REG4    0x40
+#define ACT200L_OP0     0x01 /* Enable LED1C output */
+#define ACT200L_OP1     0x02 /* Enable LED2C output */
+#define ACT200L_BLKR    0x04
+
+/* Register 5: Receive Mode register */
+#define ACT200L_REG5    0x50
+#define ACT200L_RWIDL   0x01 /* fixed 1.6us pulse mode */
+    /*.. other various IRDA bit modes, and TV remote modes..*/
+
+/* Register 6: Receive Sensitivity register #1 */
+#define ACT200L_REG6    0x60
+#define ACT200L_RS0     0x01 /* receive threshold bit 0 */
+#define ACT200L_RS1     0x02 /* receive threshold bit 1 */
+
+/* Register 7: Receive Sensitivity register #2 */
+#define ACT200L_REG7    0x70
+#define ACT200L_ENPOS   0x04 /* Ignore the falling edge */
+
+/* Register 8,9: Baud Rate Divider register #1,#2 */
+#define ACT200L_REG8    0x80
+#define ACT200L_REG9    0x90
+
+#define ACT200L_2400    0x5f
+#define ACT200L_9600    0x17
+#define ACT200L_19200   0x0b
+#define ACT200L_38400   0x05
+#define ACT200L_57600   0x03
+#define ACT200L_115200  0x01
+
+/* Register 13: Control register #3 */
+#define ACT200L_REG13   0xd0
+#define ACT200L_SHDW    0x01 /* Enable access to shadow registers */
+
+/* Register 15: Status register */
+#define ACT200L_REG15   0xf0
+
+/* Register 21: Control register #4 */
+#define ACT200L_REG21   0x50
+#define ACT200L_EXCK    0x02 /* Disable clock output driver */
+#define ACT200L_OSCL    0x04 /* oscillator in low power, medium accuracy mode */
+
+static void init_act200(void)
+{
+	int i;
+	__u8 control[] = {
+		ACT200L_REG15,
+		ACT200L_REG13 | ACT200L_SHDW,
+		ACT200L_REG21 | ACT200L_EXCK | ACT200L_OSCL,
+		ACT200L_REG13,
+		ACT200L_REG7  | ACT200L_ENPOS,
+		ACT200L_REG6  | ACT200L_RS0  | ACT200L_RS1,
+		ACT200L_REG5  | ACT200L_RWIDL,
+		ACT200L_REG4  | ACT200L_OP0  | ACT200L_OP1 | ACT200L_BLKR,
+		ACT200L_REG3  | ACT200L_B0,
+		ACT200L_REG0  | ACT200L_TXEN | ACT200L_RXEN,
+		ACT200L_REG8 |  (ACT200L_115200       & 0x0f),
+		ACT200L_REG9 | ((ACT200L_115200 >> 4) & 0x0f),
+		ACT200L_REG1 | ACT200L_LODB | ACT200L_WIDE
+	};
+
+	/* Set DLAB 1. */
+	soutp(UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN8);
+
+	/* Set divisor to 12 => 9600 Baud */
+	soutp(UART_DLM, 0);
+	soutp(UART_DLL, 12);
+
+	/* Set DLAB 0. */
+	soutp(UART_LCR, UART_LCR_WLEN8);
+	/* Set divisor to 12 => 9600 Baud */
+
+	/* power supply */
+	soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+	for (i = 0; i < 50; i++)
+		safe_udelay(1000);
+
+		/* Reset the dongle : set RTS low for 25 ms */
+	soutp(UART_MCR, UART_MCR_DTR|UART_MCR_OUT2);
+	for (i = 0; i < 25; i++)
+		udelay(1000);
+
+	soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+	udelay(100);
+
+	/* Clear DTR and set RTS to enter command mode */
+	soutp(UART_MCR, UART_MCR_RTS|UART_MCR_OUT2);
+	udelay(7);
+
+	/* send out the control register settings for 115K 7N1 SIR operation */
+	for (i = 0; i < sizeof(control); i++) {
+		soutp(UART_TX, control[i]);
+		/* one byte takes ~1042 usec to transmit at 9600,8N1 */
+		udelay(1500);
+	}
+
+	/* back to normal operation */
+	soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+	udelay(50);
+
+	udelay(1500);
+	soutp(UART_LCR, sinp(UART_LCR) | UART_LCR_DLAB);
+
+	/* Set DLAB 1. */
+	soutp(UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN7);
+
+	/* Set divisor to 1 => 115200 Baud */
+	soutp(UART_DLM, 0);
+	soutp(UART_DLL, 1);
+
+	/* Set DLAB 0. */
+	soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
+
+	/* Set DLAB 0, 7 Bit */
+	soutp(UART_LCR, UART_LCR_WLEN7);
+
+	/* enable interrupts */
+	soutp(UART_IER, sinp(UART_IER)|UART_IER_RDI);
+}
+#endif
+
+#ifdef LIRC_SIR_ACTISYS_ACT220L
+/*
+ * Derived from linux IrDA driver (net/irda/actisys.c)
+ * Drop me a mail for any kind of comment: maxx@spaceboyz.net
+ */
+
+void init_act220(void)
+{
+	int i;
+
+	/* DLAB 1 */
+	soutp(UART_LCR, UART_LCR_DLAB|UART_LCR_WLEN7);
+
+	/* 9600 baud */
+	soutp(UART_DLM, 0);
+	soutp(UART_DLL, 12);
+
+	/* DLAB 0 */
+	soutp(UART_LCR, UART_LCR_WLEN7);
+
+	/* reset the dongle, set DTR low for 10us */
+	soutp(UART_MCR, UART_MCR_RTS|UART_MCR_OUT2);
+	udelay(10);
+
+	/* back to normal (still 9600) */
+	soutp(UART_MCR, UART_MCR_DTR|UART_MCR_RTS|UART_MCR_OUT2);
+
+	/*
+	 * send RTS pulses until we reach 115200
+	 * i hope this is really the same for act220l/act220l+
+	 */
+	for (i = 0; i < 3; i++) {
+		udelay(10);
+		/* set RTS low for 10 us */
+		soutp(UART_MCR, UART_MCR_DTR|UART_MCR_OUT2);
+		udelay(10);
+		/* set RTS high for 10 us */
+		soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+	}
+
+	/* back to normal operation */
+	udelay(1500); /* better safe than sorry ;) */
+
+	/* Set DLAB 1. */
+	soutp(UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN7);
+
+	/* Set divisor to 1 => 115200 Baud */
+	soutp(UART_DLM, 0);
+	soutp(UART_DLL, 1);
+
+	/* Set DLAB 0, 7 Bit */
+	/* The dongle doesn't seem to have any problems with operation at 7N1 */
+	soutp(UART_LCR, UART_LCR_WLEN7);
+
+	/* enable interrupts */
+	soutp(UART_IER, UART_IER_RDI);
+}
+#endif
+
+static int init_lirc_sir(void)
+{
+	int retval;
+
+	init_waitqueue_head(&lirc_read_queue);
+	retval = init_port();
+	if (retval < 0)
+		return retval;
+	init_hardware();
+	printk(KERN_INFO LIRC_DRIVER_NAME
+		": Installed.\n");
+	return 0;
+}
+
+
+static int __init lirc_sir_init(void)
+{
+	int retval;
+
+	retval = init_chrdev();
+	if (retval < 0)
+		return retval;
+	retval = init_lirc_sir();
+	if (retval) {
+		drop_chrdev();
+		return retval;
+	}
+	return 0;
+}
+
+static void __exit lirc_sir_exit(void)
+{
+	drop_hardware();
+	drop_chrdev();
+	drop_port();
+	printk(KERN_INFO LIRC_DRIVER_NAME ": Uninstalled.\n");
+}
+
+module_init(lirc_sir_init);
+module_exit(lirc_sir_exit);
+
+#ifdef LIRC_SIR_TEKRAM
+MODULE_DESCRIPTION("Infrared receiver driver for Tekram Irmate 210");
+MODULE_AUTHOR("Christoph Bartelmus");
+#elif defined(LIRC_ON_SA1100)
+MODULE_DESCRIPTION("LIRC driver for StrongARM SA1100 embedded microprocessor");
+MODULE_AUTHOR("Christoph Bartelmus");
+#elif defined(LIRC_SIR_ACTISYS_ACT200L)
+MODULE_DESCRIPTION("LIRC driver for Actisys Act200L");
+MODULE_AUTHOR("Karl Bongers");
+#elif defined(LIRC_SIR_ACTISYS_ACT220L)
+MODULE_DESCRIPTION("LIRC driver for Actisys Act220L(+)");
+MODULE_AUTHOR("Jan Roemisch");
+#else
+MODULE_DESCRIPTION("Infrared receiver driver for SIR type serial ports");
+MODULE_AUTHOR("Milan Pikula");
+#endif
+MODULE_LICENSE("GPL");
+
+#ifdef LIRC_ON_SA1100
+module_param(irq, int, S_IRUGO);
+MODULE_PARM_DESC(irq, "Interrupt (16)");
+#else
+module_param(io, int, S_IRUGO);
+MODULE_PARM_DESC(io, "I/O address base (0x3f8 or 0x2f8)");
+
+module_param(irq, int, S_IRUGO);
+MODULE_PARM_DESC(irq, "Interrupt (4 or 3)");
+
+module_param(threshold, int, S_IRUGO);
+MODULE_PARM_DESC(threshold, "space detection threshold (3)");
+#endif
+
+module_param(debug, bool, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(debug, "Enable debugging messages");