Merge tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: imx: fixes for 3.19" from Shawn Guo:

The i.MX fixes for 3.19:
 - One fix for incorrect i.MX25 SPI1 clock assignment in device tree,
   which causes system hang when accessing SPI1.
 - Correct i.MX6SX QSPI parent clock configuration to fix a kernel Oops.
 - Fix ULPI PHY reset modelling on imx51-babbage board to remove the
   dependency on bootloader for USB3317 ULPI PHY reset.
 - Correct video divider setting on i.MX6Q rev T0 1.0 to fix the issue
   that HDMI is not working at high resolution on T0 1.0.
 - One incremental fix for CODA960 VPU enabling in device tree to
   correct interrupt order.
 - LS1021A SCFG block works in BE mode, add device tree property
   big-endian to make it right.

* tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
  ARM: imx6sx: Set PLL2 as parent of QSPI clocks
  ARM: dts: imx25: Fix the SPI1 clocks
  ARM: clk-imx6q: fix video divider for rev T0 1.0
  ARM: dts: imx6qdl: Fix CODA960 interrupt order
  ARM: ls1021a: dtsi: add 'big-endian' property for scfg node

Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/imx25.dtsi

@@ -162,7 +162,7 @@
 				#size-cells = <0>;
 				compatible = "fsl,imx25-cspi", "fsl,imx35-cspi";
 				reg = <0x43fa4000 0x4000>;
-				clocks = <&clks 62>, <&clks 62>;
+				clocks = <&clks 78>, <&clks 78>;
 				clock-names = "ipg", "per";
 				interrupts = <14>;
 				status = "disabled";

arch/arm/boot/dts/imx51-babbage.dts

@@ -127,24 +127,12 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		reg_usbh1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1reg>;
-			reg = <0>;
-			regulator-name = "usbh1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio2 5 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		reg_usbotg_vbus: regulator@1 {
+		reg_hub_reset: regulator@0 {
 			compatible = "regulator-fixed";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usbotgreg>;
-			reg = <1>;
-			regulator-name = "usbotg_vbus";
+			reg = <0>;
+			regulator-name = "hub_reset";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
@@ -176,6 +164,7 @@
 			reg = <0>;
 			clocks = <&clks IMX5_CLK_DUMMY>;
 			clock-names = "main_clk";
+			reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -419,7 +408,7 @@
 &usbh1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh1>;
-	vbus-supply = <&reg_usbh1_vbus>;
+	vbus-supply = <&reg_hub_reset>;
 	fsl,usbphy = <&usbh1phy>;
 	phy_type = "ulpi";
 	status = "okay";
@@ -429,7 +418,6 @@
 	dr_mode = "otg";
 	disable-over-current;
 	phy_type = "utmi_wide";
-	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx6qdl.dtsi

@@ -335,8 +335,8 @@
 			vpu: vpu@02040000 {
 				compatible = "cnm,coda960";
 				reg = <0x02040000 0x3c000>;
-				interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>,
-				             <0 12 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>,
+					     <0 3 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "bit", "jpeg";
 				clocks = <&clks IMX6QDL_CLK_VPU_AXI>,
 					 <&clks IMX6QDL_CLK_MMDC_CH0_AXI>,

arch/arm/boot/dts/ls1021a.dtsi

@@ -142,6 +142,7 @@
 		scfg: scfg@1570000 {
 			compatible = "fsl,ls1021a-scfg", "syscon";
 			reg = <0x0 0x1570000 0x0 0x10000>;
+			big-endian;
 		};
 
 		clockgen: clocking@1ee1000 {

arch/arm/mach-imx/clk-imx6q.c

@@ -144,7 +144,7 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 		post_div_table[1].div = 1;
 		post_div_table[2].div = 1;
 		video_div_table[1].div = 1;
-		video_div_table[2].div = 1;
+		video_div_table[3].div = 1;
 	}
 
 	clk[IMX6QDL_PLL1_BYPASS_SRC] = imx_clk_mux("pll1_bypass_src", base + 0x00, 14, 2, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels));

arch/arm/mach-imx/clk-imx6sx.c

@@ -558,6 +558,9 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node)
 	clk_set_parent(clks[IMX6SX_CLK_GPU_CORE_SEL], clks[IMX6SX_CLK_PLL3_PFD0]);
 	clk_set_parent(clks[IMX6SX_CLK_GPU_AXI_SEL], clks[IMX6SX_CLK_PLL3_PFD0]);
 
+	clk_set_parent(clks[IMX6SX_CLK_QSPI1_SEL], clks[IMX6SX_CLK_PLL2_BUS]);
+	clk_set_parent(clks[IMX6SX_CLK_QSPI2_SEL], clks[IMX6SX_CLK_PLL2_BUS]);
+
 	/* Set initial power mode */
 	imx6q_set_lpm(WAIT_CLOCKED);
 }