Merge tag 'ux500-armsoc-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt

Merge "ux500 Devicetree updates for v4.7" from Linus Walleij:

- Use generic include files
- Make accelerometers open drain on the TVK board

* tag 'ux500-armsoc-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: dts: ux500: configure the accelerometers open drain
  ARM: dts: ux500: use the GIC include header
  ARM: dts: ux500: use the GPIO DT header

arch/arm/boot/dts/ste-ccu9540.dts

@@ -49,7 +49,7 @@
 			cap-mmc-highspeed;
 			vmmc-supply = <&ab8500_ldo_aux3_reg>;
 
-			cd-gpios  = <&gpio7 6 0x4>; // 230
+			cd-gpios  = <&gpio7 6 GPIO_ACTIVE_HIGH>; // 230
 			cd-inverted;
 
 			status = "okay";

arch/arm/boot/dts/ste-dbx5x0.dtsi

@@ -10,8 +10,10 @@
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mfd/dbx500-prcmu.h>
 #include <dt-bindings/arm/ux500_pm_domains.h>
+#include <dt-bindings/gpio/gpio.h>
 #include "skeleton.dtsi"
 
 / {
@@ -203,14 +205,14 @@
 		L2: l2-cache {
 			compatible = "arm,pl310-cache";
 			reg = <0xa0412000 0x1000>;
-			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-level = <2>;
 		};
 
 		pmu {
 			compatible = "arm,cortex-a9-pmu";
-			interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		pm_domains: pm_domains0 {
@@ -253,7 +255,7 @@
 			/* Nomadik System Timer */
 			compatible = "st,nomadik-mtu";
 			reg = <0xa03c6000 0x1000>;
-			interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 
 			clocks = <&prcmu_clk PRCMU_TIMCLK>, <&prcc_pclk 6 6>;
 			clock-names = "timclk", "apb_pclk";
@@ -262,7 +264,7 @@
 		timer@a0410600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0xa0410600 0x20>;
-			interrupts = <1 13 0x304>; /* IRQ level high per-CPU */
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 
 			clocks = <&smp_twd_clk>;
 		};
@@ -270,14 +272,14 @@
 		watchdog@a0410620 {
 			compatible = "arm,cortex-a9-twd-wdt";
 			reg = <0xa0410620 0x20>;
-			interrupts = <1 14 0x304>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&smp_twd_clk>;
 		};
 
 		rtc@80154000 {
 			compatible = "arm,rtc-pl031", "arm,primecell";
 			reg = <0x80154000 0x1000>;
-			interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
 
 			clocks = <&rtc_clk>;
 			clock-names = "apb_pclk";
@@ -287,7 +289,7 @@
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
 			reg =  <0x8012e000 0x80>;
-			interrupts = <0 119 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			st,supports-sleepmode;
@@ -302,7 +304,7 @@
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
 			reg =  <0x8012e080 0x80>;
-			interrupts = <0 120 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			st,supports-sleepmode;
@@ -317,7 +319,7 @@
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
 			reg =  <0x8000e000 0x80>;
-			interrupts = <0 121 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			st,supports-sleepmode;
@@ -332,7 +334,7 @@
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
 			reg =  <0x8000e080 0x80>;
-			interrupts = <0 122 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			st,supports-sleepmode;
@@ -347,7 +349,7 @@
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
 			reg =  <0x8000e100 0x80>;
-			interrupts = <0 123 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			st,supports-sleepmode;
@@ -362,7 +364,7 @@
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
 			reg =  <0x8000e180 0x80>;
-			interrupts = <0 124 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			st,supports-sleepmode;
@@ -377,7 +379,7 @@
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
 			reg =  <0x8011e000 0x80>;
-			interrupts = <0 125 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			st,supports-sleepmode;
@@ -392,7 +394,7 @@
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
 			reg =  <0x8011e080 0x80>;
-			interrupts = <0 126 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			st,supports-sleepmode;
@@ -407,7 +409,7 @@
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
 			reg =  <0xa03fe000 0x80>;
-			interrupts = <0 127 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			st,supports-sleepmode;
@@ -429,7 +431,7 @@
 		usb_per5@a03e0000 {
 			compatible = "stericsson,db8500-musb";
 			reg = <0xa03e0000 0x10000>;
-			interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "mc";
 
 			dr_mode = "otg";
@@ -467,7 +469,7 @@
 			compatible = "stericsson,db8500-dma40", "stericsson,dma40";
 			reg = <0x801C0000 0x1000 0x40010000 0x800>;
 			reg-names = "base", "lcpa";
-			interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 
 			#dma-cells = <3>;
 			memcpy-channels = <56 57 58 59 60>;
@@ -479,7 +481,7 @@
 			compatible = "stericsson,db8500-prcmu";
 			reg = <0x80157000 0x2000>, <0x801b0000 0x8000>, <0x801b8000 0x1000>;
 			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm";
-			interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			interrupt-controller;
@@ -597,7 +599,7 @@
 			ab8500 {
 				compatible = "stericsson,ab8500";
 				interrupt-parent = <&intc>;
-				interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
 
@@ -785,7 +787,7 @@
 		i2c@80004000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80004000 0x1000>;
-			interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -800,7 +802,7 @@
 		i2c@80122000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80122000 0x1000>;
-			interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -816,7 +818,7 @@
 		i2c@80128000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80128000 0x1000>;
-			interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -832,7 +834,7 @@
 		i2c@80110000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80110000 0x1000>;
-			interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -848,7 +850,7 @@
 		i2c@8012a000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x8012a000 0x1000>;
-			interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -864,7 +866,7 @@
 		ssp@80002000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80002000 0x1000>;
-			interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			clocks = <&prcc_kclk 3 1>, <&prcc_pclk 3 1>;
@@ -878,7 +880,7 @@
 		ssp@80003000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80003000 0x1000>;
-			interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			clocks = <&prcc_kclk 3 2>, <&prcc_pclk 3 2>;
@@ -892,7 +894,7 @@
 		spi@8011a000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x8011a000 0x1000>;
-			interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
@@ -907,7 +909,7 @@
 		spi@80112000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80112000 0x1000>;
-			interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
@@ -922,7 +924,7 @@
 		spi@80111000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80111000 0x1000>;
-			interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
@@ -937,7 +939,7 @@
 		spi@80129000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80129000 0x1000>;
-			interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
@@ -952,7 +954,7 @@
 		ux500_serial0: uart@80120000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x80120000 0x1000>;
-			interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
 
 			dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */
 			       <&dma 13 0 0x0>; /* Logical - MemToDev */
@@ -967,7 +969,7 @@
 		ux500_serial1: uart@80121000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x80121000 0x1000>;
-			interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 
 			dmas = <&dma 12 0 0x2>, /* Logical - DevToMem */
 			       <&dma 12 0 0x0>; /* Logical - MemToDev */
@@ -982,7 +984,7 @@
 		ux500_serial2: uart@80007000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x80007000 0x1000>;
-			interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 
 			dmas = <&dma 11 0 0x2>, /* Logical - DevToMem */
 			       <&dma 11 0 0x0>; /* Logical - MemToDev */
@@ -997,7 +999,7 @@
 		sdi0_per1@80126000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80126000 0x1000>;
-			interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
 
 			dmas = <&dma 29 0 0x2>, /* Logical - DevToMem */
 			       <&dma 29 0 0x0>; /* Logical - MemToDev */
@@ -1013,7 +1015,7 @@
 		sdi1_per2@80118000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80118000 0x1000>;
-			interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
 
 			dmas = <&dma 32 0 0x2>, /* Logical - DevToMem */
 			       <&dma 32 0 0x0>; /* Logical - MemToDev */
@@ -1029,7 +1031,7 @@
 		sdi2_per3@80005000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80005000 0x1000>;
-			interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 
 			dmas = <&dma 28 0 0x2>, /* Logical - DevToMem */
 			       <&dma 28 0 0x0>; /* Logical - MemToDev */
@@ -1045,7 +1047,7 @@
 		sdi3_per2@80119000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80119000 0x1000>;
-			interrupts = <0 59 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
 
 			dmas = <&dma 41 0 0x2>, /* Logical - DevToMem */
 			       <&dma 41 0 0x0>; /* Logical - MemToDev */
@@ -1061,7 +1063,7 @@
 		sdi4_per2@80114000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80114000 0x1000>;
-			interrupts = <0 99 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
 
 			dmas = <&dma 42 0 0x2>, /* Logical - DevToMem */
 			       <&dma 42 0 0x0>; /* Logical - MemToDev */
@@ -1077,7 +1079,7 @@
 		sdi5_per3@80008000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80008000 0x1000>;
-			interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 
 			dmas = <&dma 43 0 0x2>, /* Logical - DevToMem */
 			       <&dma 43 0 0x0>; /* Logical - MemToDev */
@@ -1093,7 +1095,7 @@
 		msp0: msp@80123000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80123000 0x1000>;
-			interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 			v-ape-supply = <&db8500_vape_reg>;
 
 			dmas = <&dma 31 0 0x12>, /* Logical - DevToMem - HighPrio */
@@ -1109,7 +1111,7 @@
 		msp1: msp@80124000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80124000 0x1000>;
-			interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
 			v-ape-supply = <&db8500_vape_reg>;
 
 			/* This DMA channel only exist on DB8500 v1 */
@@ -1126,7 +1128,7 @@
 		msp2: msp@80117000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80117000 0x1000>;
-			interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
 			v-ape-supply = <&db8500_vape_reg>;
 
 			dmas = <&dma 14 0 0x12>, /* Logical  - DevToMem - HighPrio */
@@ -1143,7 +1145,7 @@
 		msp3: msp@80125000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80125000 0x1000>;
-			interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
 			v-ape-supply = <&db8500_vape_reg>;
 
 			/* This DMA channel only exist on DB8500 v2 */
@@ -1176,7 +1178,7 @@
 			      <0xa0351000 0x1000>, /* DSI link 1 */
 			      <0xa0352000 0x1000>, /* DSI link 2 */
 			      <0xa0353000 0x1000>; /* DSI link 3 */
-			interrupts = <0 48 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
 				 <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
 				 <&prcmu_clk PRCMU_PLLDSI>, /* HDMI clock */
@@ -1190,7 +1192,7 @@
 		cryp@a03cb000 {
 			compatible = "stericsson,ux500-cryp";
 			reg = <0xa03cb000 0x1000>;
-			interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
 
 			v-ape-supply = <&db8500_vape_reg>;
 			clocks = <&prcc_pclk 6 1>;

arch/arm/boot/dts/ste-href-stuib.dtsi

@@ -22,13 +22,13 @@
 
 		button@139 {
 			/* Proximity sensor */
-			gpios = <&gpio6 25 0x4>;
+			gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
 			linux,code = <11>; /* SW_FRONT_PROXIMITY */
 			label = "SFH7741 Proximity Sensor";
 		};
 		button@145 {
 			/* Hall sensor */
-			gpios = <&gpio4 17 0x4>;
+			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
 			linux,code = <0>; /* SW_LID */
 			label = "HED54XXU11 Hall Effect Sensor";
 		};

arch/arm/boot/dts/ste-href-tvk1281618.dtsi

@@ -24,13 +24,13 @@
 
 		button@139 {
 			/* Proximity sensor */
-			gpios = <&gpio6 25 0x4>;
+			gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
 			linux,code = <11>; /* SW_FRONT_PROXIMITY */
 			label = "SFH7741 Proximity Sensor";
 		};
 		button@145 {
 			/* Hall sensor */
-			gpios = <&gpio4 17 0x4>;
+			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
 			linux,code = <0>; /* SW_LID */
 			label = "HED54XXU11 Hall Effect Sensor";
 		};
@@ -93,14 +93,15 @@
 				/* Accelerometer */
 				compatible = "st,lsm303dlh-accel";
 				st,drdy-int-pin = <1>;
+				drive-open-drain;
 				reg = <0x18>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
 				vddio-supply = <&db8500_vsmps2_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&accel_tvk_mode>;
 				interrupt-parent = <&gpio2>;
-				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
-					     <19 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
+					     <19 IRQ_TYPE_EDGE_FALLING>;
 			};
 			lsm303dlh@1e {
 				/*
@@ -118,14 +119,15 @@
 				/* Accelerometer */
 				compatible = "st,lis331dl-accel";
 				st,drdy-int-pin = <1>;
+				drive-open-drain;
 				reg = <0x1c>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
 				vddio-supply = <&db8500_vsmps2_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&accel_tvk_mode>;
 				interrupt-parent = <&gpio2>;
-				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
-					     <19 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
+					     <19 IRQ_TYPE_EDGE_FALLING>;
 			};
 			ak8974@0f {
 				/* Magnetometer */
@@ -216,7 +218,7 @@
 					/* Accelerometer interrupt lines 1 & 2 */
 					tvk_cfg {
 						pins = "GPIO82_C1", "GPIO83_D3";
-						ste,config = <&gpio_in_pd>;
+						ste,config = <&gpio_in_pu>;
 					};
 				};
 			};

arch/arm/boot/dts/ste-hrefprev60.dtsi

@@ -18,7 +18,7 @@
 / {
 	gpio_keys {
 		button@1 {
-			gpios = <&tc3589x_gpio 7 0x4>;
+			gpios = <&tc3589x_gpio 7 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -68,12 +68,12 @@
 
 		// External Micro SD slot
 		sdi0_per1@80126000 {
-			cd-gpios  = <&tc3589x_gpio 3 0x4>;
+			cd-gpios  = <&tc3589x_gpio 3 GPIO_ACTIVE_HIGH>;
 		};
 
 		vmmci: regulator-gpio {
-			gpios = <&tc3589x_gpio 18 0x4>;
-			enable-gpio = <&tc3589x_gpio 17 0x4>;
+			gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
+			enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
 		};
 
 		pinctrl {

arch/arm/boot/dts/ste-hrefv60plus.dtsi

@@ -20,12 +20,12 @@
 	soc {
 		// External Micro SD slot
 		sdi0_per1@80126000 {
-			cd-gpios  = <&gpio2 31 0x4>; // 95
+			cd-gpios  = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
 		};
 
 		vmmci: regulator-gpio {
-			gpios = <&gpio0 5 0x4>;
-			enable-gpio = <&gpio5 9 0x4>;
+			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+			enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
 		};
 
 		pinctrl {

arch/arm/boot/dts/ste-snowball.dts

@@ -50,35 +50,35 @@
 			wakeup-source;
 			linux,code = <2>;
 			label = "userpb";
-			gpios = <&gpio1 0 0x4>;
+			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
 		};
 		button@2 {
 			debounce_interval = <50>;
 			wakeup-source;
 			linux,code = <3>;
 			label = "extkb1";
-			gpios = <&gpio4 23 0x4>;
+			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
 		};
 		button@3 {
 			debounce_interval = <50>;
 			wakeup-source;
 			linux,code = <4>;
 			label = "extkb2";
-			gpios = <&gpio4 24 0x4>;
+			gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
 		};
 		button@4 {
 			debounce_interval = <50>;
 			wakeup-source;
 			linux,code = <5>;
 			label = "extkb3";
-			gpios = <&gpio5 1 0x4>;
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
 		};
 		button@5 {
 			debounce_interval = <50>;
 			wakeup-source;
 			linux,code = <6>;
 			label = "extkb4";
-			gpios = <&gpio5 2 0x4>;
+			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -88,7 +88,7 @@
 		pinctrl-0 = <&gpioled_snowball_mode>;
 		used-led {
 			label = "user_led";
-			gpios = <&gpio4 14 0x4>;
+			gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
@@ -155,8 +155,8 @@
 		vmmci: regulator-gpio {
 			compatible = "regulator-gpio";
 
-			gpios = <&gpio7 4 0x4>;
-			enable-gpio = <&gpio6 25 0x4>;
+			gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
+			enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>;
 
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <2900000>;
@@ -182,8 +182,7 @@
 			pinctrl-0 = <&sdi0_default_mode>;
 			pinctrl-1 = <&sdi0_sleep_mode>;
 
-			cd-gpios  = <&gpio6 26 0x4>; // 218
-			cd-inverted;
+			cd-gpios  = <&gpio6 26 GPIO_ACTIVE_LOW>; // 218
 
 			status = "okay";
 		};