iwlwifi: trans: don't configure the set_active in SCD for dvm

This configuration is not needed for dvm, and it actually
broke it.

Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

drivers/net/wireless/iwlwifi/iwl-trans.h

@@ -377,6 +377,7 @@ enum iwl_trans_status {
  *	if unset 4k will be the RX buffer size
  * @bc_table_dword: set to true if the BC table expects the byte count to be
  *	in DWORD (as opposed to bytes)
+ * @scd_set_active: should the transport configure the SCD for HCMD queue
  * @queue_watchdog_timeout: time (in ms) after which queues
  *	are considered stuck and will trigger device restart
  * @command_names: array of command names, must be 256 entries
@@ -392,6 +393,7 @@ struct iwl_trans_config {
 
 	bool rx_buf_size_8k;
 	bool bc_table_dword;
+	bool scd_set_active;
 	unsigned int queue_watchdog_timeout;
 	const char *const *command_names;
 };

drivers/net/wireless/iwlwifi/mvm/ops.c

@@ -460,6 +460,7 @@ iwl_op_mode_mvm_start(struct iwl_trans *trans, const struct iwl_cfg *cfg,
 
 	trans_cfg.cmd_queue = IWL_MVM_CMD_QUEUE;
 	trans_cfg.cmd_fifo = IWL_MVM_TX_FIFO_CMD;
+	trans_cfg.scd_set_active = true;
 
 	snprintf(mvm->hw->wiphy->fw_version,
 		 sizeof(mvm->hw->wiphy->fw_version),

drivers/net/wireless/iwlwifi/pcie/internal.h

@@ -257,6 +257,7 @@ iwl_pcie_get_scratchbuf_dma(struct iwl_txq *txq, int idx)
  * @cmd_queue - command queue number
  * @rx_buf_size_8k: 8 kB RX buffer size
  * @bc_table_dword: true if the BC table expects DWORD (as opposed to bytes)
+ * @scd_set_active: should the transport configure the SCD for HCMD queue
  * @rx_page_order: page order for receive buffer size
  * @wd_timeout: queue watchdog timeout (jiffies)
  * @reg_lock: protect hw register access
@@ -306,6 +307,7 @@ struct iwl_trans_pcie {
 
 	bool rx_buf_size_8k;
 	bool bc_table_dword;
+	bool scd_set_active;
 	u32 rx_page_order;
 
 	const char *const *command_names;

drivers/net/wireless/iwlwifi/pcie/trans.c

@@ -1171,6 +1171,7 @@ static void iwl_trans_pcie_configure(struct iwl_trans *trans,
 
 	trans_pcie->command_names = trans_cfg->command_names;
 	trans_pcie->bc_table_dword = trans_cfg->bc_table_dword;
+	trans_pcie->scd_set_active = trans_cfg->scd_set_active;
 
 	/* Initialize NAPI here - it should be before registering to mac80211
 	 * in the opmode but after the HW struct is allocated.

drivers/net/wireless/iwlwifi/pcie/tx.c

@@ -1080,7 +1080,8 @@ void iwl_trans_pcie_txq_enable(struct iwl_trans *trans, int txq_id, u16 ssn,
 		fifo = cfg->fifo;
 
 		/* Disable the scheduler prior configuring the cmd queue */
-		if (txq_id == trans_pcie->cmd_queue)
+		if (txq_id == trans_pcie->cmd_queue &&
+		    trans_pcie->scd_set_active)
 			iwl_scd_enable_set_active(trans, 0);
 
 		/* Stop this Tx queue before configuring it */
@@ -1142,7 +1143,8 @@ void iwl_trans_pcie_txq_enable(struct iwl_trans *trans, int txq_id, u16 ssn,
 			       SCD_QUEUE_STTS_REG_MSK);
 
 		/* enable the scheduler for this queue (only) */
-		if (txq_id == trans_pcie->cmd_queue)
+		if (txq_id == trans_pcie->cmd_queue &&
+		    trans_pcie->scd_set_active)
 			iwl_scd_enable_set_active(trans, BIT(txq_id));
 	}