staging: fbtft: Modify block comments based on kernel coding style

Add the required trailing * on subsequent lines as well as move the */
on a separate line. Checkpatch found this issue.

Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/fbtft/fb_ili9163.c

@@ -39,11 +39,11 @@
 #endif
 
 /* ILI9163C commands */
-#define CMD_FRMCTR1	0xB1 /* Frame Rate Control
-				(In normal mode/Full colors) */
+#define CMD_FRMCTR1	0xB1 /* Frame Rate Control */
+			     /*	(In normal mode/Full colors) */
 #define CMD_FRMCTR2	0xB2 /* Frame Rate Control (In Idle mode/8-colors) */
-#define CMD_FRMCTR3	0xB3 /* Frame Rate Control
-				(In Partial mode/full colors) */
+#define CMD_FRMCTR3	0xB3 /* Frame Rate Control */
+			     /*	(In Partial mode/full colors) */
 #define CMD_DINVCTR	0xB4 /* Display Inversion Control */
 #define CMD_RGBBLK	0xB5 /* RGB Interface Blanking Porch setting */
 #define CMD_DFUNCTR	0xB6 /* Display Function set 5 */
@@ -63,17 +63,18 @@
 #define CMD_GAMRSEL	0xF2 /* GAM_R_SEL */
 
 /*
-This display:
-http://www.ebay.com/itm/Replace-Nokia-5110-LCD-1-44-Red-Serial-128X128-SPI-Color-TFT-LCD-Display-Module-/271422122271
-This particular display has a design error! The controller has 3 pins to
-configure to constrain the memory and resolution to a fixed dimension (in
-that case 128x128) but they leaved those pins configured for 128x160 so
-there was several pixel memory addressing problems.
-I solved by setup several parameters that dinamically fix the resolution as
-needit so below the parameters for this display. If you have a strain or a
-correct display (can happen with chinese) you can copy those parameters and
-create setup for different displays.
-*/
+ * This display:
+ * http://www.ebay.com/itm/Replace-Nokia-5110-LCD-1-44-Red-Serial-128X128-SPI-
+ * Color-TFT-LCD-Display-Module-/271422122271
+ * This particular display has a design error! The controller has 3 pins to
+ * configure to constrain the memory and resolution to a fixed dimension (in
+ * that case 128x128) but they leaved those pins configured for 128x160 so
+ * there was several pixel memory addressing problems.
+ * I solved by setup several parameters that dinamically fix the resolution as
+ * needit so below the parameters for this display. If you have a strain or a
+ * correct display (can happen with chinese) you can copy those parameters and
+ * create setup for different displays.
+ */
 
 #ifdef RED
 #define __OFFSET		32 /*see note 2 - this is the red version */
@@ -153,25 +154,25 @@ static void set_addr_win(struct fbtft_par *par, int xs, int ys,
 }
 
 /*
-7) MY:  1(bottom to top),	0(top to bottom)    Row Address Order
-6) MX:  1(R to L),		0(L to R)	    Column Address Order
-5) MV:  1(Exchanged),		0(normal)	    Row/Column exchange
-4) ML:  1(bottom to top),	0(top to bottom)    Vertical Refresh Order
-3) RGB: 1(BGR),			0(RGB)		    Color Space
-2) MH:  1(R to L),		0(L to R)	    Horizontal Refresh Order
-1)
-0)
-
-	MY, MX, MV, ML,RGB, MH, D1, D0
-	0 | 0 | 0 | 0 | 1 | 0 | 0 | 0	//normal
-	1 | 0 | 0 | 0 | 1 | 0 | 0 | 0	//Y-Mirror
-	0 | 1 | 0 | 0 | 1 | 0 | 0 | 0	//X-Mirror
-	1 | 1 | 0 | 0 | 1 | 0 | 0 | 0	//X-Y-Mirror
-	0 | 0 | 1 | 0 | 1 | 0 | 0 | 0	//X-Y Exchange
-	1 | 0 | 1 | 0 | 1 | 0 | 0 | 0	//X-Y Exchange, Y-Mirror
-	0 | 1 | 1 | 0 | 1 | 0 | 0 | 0	//XY exchange
-	1 | 1 | 1 | 0 | 1 | 0 | 0 | 0
-*/
+ * 7) MY:  1(bottom to top),	0(top to bottom)    Row Address Order
+ * 6) MX:  1(R to L),		0(L to R)	    Column Address Order
+ * 5) MV:  1(Exchanged),	0(normal)	    Row/Column exchange
+ * 4) ML:  1(bottom to top),	0(top to bottom)    Vertical Refresh Order
+ * 3) RGB: 1(BGR),		0(RGB)		    Color Space
+ * 2) MH:  1(R to L),		0(L to R)	    Horizontal Refresh Order
+ * 1)
+ * 0)
+ *
+ *	MY, MX, MV, ML,RGB, MH, D1, D0
+ *	0 | 0 | 0 | 0 | 1 | 0 | 0 | 0	//normal
+ *	1 | 0 | 0 | 0 | 1 | 0 | 0 | 0	//Y-Mirror
+ *	0 | 1 | 0 | 0 | 1 | 0 | 0 | 0	//X-Mirror
+ *	1 | 1 | 0 | 0 | 1 | 0 | 0 | 0	//X-Y-Mirror
+ *	0 | 0 | 1 | 0 | 1 | 0 | 0 | 0	//X-Y Exchange
+ *	1 | 0 | 1 | 0 | 1 | 0 | 0 | 0	//X-Y Exchange, Y-Mirror
+ *	0 | 1 | 1 | 0 | 1 | 0 | 0 | 0	//XY exchange
+ *	1 | 1 | 1 | 0 | 1 | 0 | 0 | 0
+ */
 static int set_var(struct fbtft_par *par)
 {
 	u8 mactrl_data = 0; /* Avoid compiler warning */

drivers/staging/fbtft/fb_ili9320.c

@@ -216,10 +216,10 @@ static int set_var(struct fbtft_par *par)
 }
 
 /*
-  Gamma string format:
-    VRP0 VRP1 RP0 RP1 KP0 KP1 KP2 KP3 KP4 KP5
-    VRN0 VRN1 RN0 RN1 KN0 KN1 KN2 KN3 KN4 KN5
-*/
+ * Gamma string format:
+ *  VRP0 VRP1 RP0 RP1 KP0 KP1 KP2 KP3 KP4 KP5
+ *  VRN0 VRN1 RN0 RN1 KN0 KN1 KN2 KN3 KN4 KN5
+ */
 #define CURVE(num, idx)  curves[num * par->gamma.num_values + idx]
 static int set_gamma(struct fbtft_par *par, unsigned long *curves)
 {

drivers/staging/fbtft/fb_ili9325.c

@@ -56,42 +56,42 @@ module_param(vcm, uint, 0);
 MODULE_PARM_DESC(vcm, "Set the internal VcomH voltage");
 
 /*
-Verify that this configuration is within the Voltage limits
-
-Display module configuration: Vcc = IOVcc = Vci = 3.3V
-
- Voltages
-----------
-Vci                                =   3.3
-Vci1           =  Vci * 0.80       =   2.64
-DDVDH          =  Vci1 * 2         =   5.28
-VCL            = -Vci1             =  -2.64
-VREG1OUT       =  Vci * 1.85       =   4.88
-VCOMH          =  VREG1OUT * 0.735 =   3.59
-VCOM amplitude =  VREG1OUT * 0.98  =   4.79
-VGH            =  Vci * 4          =  13.2
-VGL            = -Vci * 4          = -13.2
-
- Limits
---------
-Power supplies
-1.65 < IOVcc < 3.30   =>  1.65 < 3.3 < 3.30
-2.40 < Vcc   < 3.30   =>  2.40 < 3.3 < 3.30
-2.50 < Vci   < 3.30   =>  2.50 < 3.3 < 3.30
-
-Source/VCOM power supply voltage
- 4.50 < DDVDH < 6.0   =>  4.50 <  5.28 <  6.0
--3.0  < VCL   < -2.0  =>  -3.0 < -2.64 < -2.0
-VCI - VCL < 6.0       =>  5.94 < 6.0
-
-Gate driver output voltage
- 10  < VGH   < 20     =>   10 <  13.2  < 20
--15  < VGL   < -5     =>  -15 < -13.2  < -5
-VGH - VGL < 32        =>   26.4 < 32
-
-VCOM driver output voltage
-VCOMH - VCOML < 6.0   =>  4.79 < 6.0
-*/
+ * Verify that this configuration is within the Voltage limits
+ *
+ * Display module configuration: Vcc = IOVcc = Vci = 3.3V
+ *
+ * Voltages
+ * ----------
+ * Vci                                =   3.3
+ * Vci1           =  Vci * 0.80       =   2.64
+ * DDVDH          =  Vci1 * 2         =   5.28
+ * VCL            = -Vci1             =  -2.64
+ * VREG1OUT       =  Vci * 1.85       =   4.88
+ * VCOMH          =  VREG1OUT * 0.735 =   3.59
+ * VCOM amplitude =  VREG1OUT * 0.98  =   4.79
+ * VGH            =  Vci * 4          =  13.2
+ * VGL            = -Vci * 4          = -13.2
+ *
+ * Limits
+ * --------
+ * Power supplies
+ * 1.65 < IOVcc < 3.30   =>  1.65 < 3.3 < 3.30
+ * 2.40 < Vcc   < 3.30   =>  2.40 < 3.3 < 3.30
+ * 2.50 < Vci   < 3.30   =>  2.50 < 3.3 < 3.30
+ *
+ * Source/VCOM power supply voltage
+ *  4.50 < DDVDH < 6.0   =>  4.50 <  5.28 <  6.0
+ * -3.0  < VCL   < -2.0  =>  -3.0 < -2.64 < -2.0
+ * VCI - VCL < 6.0       =>  5.94 < 6.0
+ *
+ * Gate driver output voltage
+ *  10  < VGH   < 20     =>   10 <  13.2  < 20
+ * -15  < VGL   < -5     =>  -15 < -13.2  < -5
+ * VGH - VGL < 32        =>   26.4 < 32
+ *
+ * VCOM driver output voltage
+ * VCOMH - VCOML < 6.0   =>  4.79 < 6.0
+ */
 
 static int init_display(struct fbtft_par *par)
 {
@@ -213,10 +213,10 @@ static int set_var(struct fbtft_par *par)
 }
 
 /*
-  Gamma string format:
-    VRP0 VRP1 RP0 RP1 KP0 KP1 KP2 KP3 KP4 KP5
-    VRN0 VRN1 RN0 RN1 KN0 KN1 KN2 KN3 KN4 KN5
-*/
+ * Gamma string format:
+ *  VRP0 VRP1 RP0 RP1 KP0 KP1 KP2 KP3 KP4 KP5
+ *  VRN0 VRN1 RN0 RN1 KN0 KN1 KN2 KN3 KN4 KN5
+ */
 #define CURVE(num, idx)  curves[num * par->gamma.num_values + idx]
 static int set_gamma(struct fbtft_par *par, unsigned long *curves)
 {

drivers/staging/fbtft/fb_ili9341.c

@@ -116,10 +116,10 @@ static int set_var(struct fbtft_par *par)
 }
 
 /*
-  Gamma string format:
-    Positive: Par1 Par2 [...] Par15
-    Negative: Par1 Par2 [...] Par15
-*/
+ * Gamma string format:
+ *  Positive: Par1 Par2 [...] Par15
+ *  Negative: Par1 Par2 [...] Par15
+ */
 #define CURVE(num, idx)  curves[num * par->gamma.num_values + idx]
 static int set_gamma(struct fbtft_par *par, unsigned long *curves)
 {