usb: phy: ab8500: Drop AB8540/9540 support

The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.

Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

drivers/usb/phy/phy-ab8500-usb.c

@@ -29,17 +29,12 @@
 /* Bank AB8500_USB */
 #define AB8500_USB_LINE_STAT_REG 0x80
 #define AB8505_USB_LINE_STAT_REG 0x94
-#define AB8540_USB_LINK_STAT_REG 0x94
-#define AB9540_USB_LINK_STAT_REG 0x94
-#define AB8540_USB_OTG_CTL_REG 0x87
 #define AB8500_USB_PHY_CTRL_REG 0x8A
-#define AB8540_VBUS_CTRL_REG 0x82
 
 /* Bank AB8500_DEVELOPMENT */
 #define AB8500_BANK12_ACCESS 0x00
 
 /* Bank AB8500_DEBUG */
-#define AB8540_DEBUG 0x32
 #define AB8500_USB_PHY_TUNE1 0x05
 #define AB8500_USB_PHY_TUNE2 0x06
 #define AB8500_USB_PHY_TUNE3 0x07
@@ -53,10 +48,6 @@
 #define AB8500_BIT_WD_CTRL_ENABLE (1 << 0)
 #define AB8500_BIT_WD_CTRL_KICK (1 << 1)
 #define AB8500_BIT_SOURCE2_VBUSDET (1 << 7)
-#define AB8540_BIT_OTG_CTL_VBUS_VALID_ENA (1 << 0)
-#define AB8540_BIT_OTG_CTL_ID_HOST_ENA (1 << 1)
-#define AB8540_BIT_OTG_CTL_ID_DEV_ENA (1 << 5)
-#define AB8540_BIT_VBUS_CTRL_CHARG_DET_ENA (1 << 0)
 
 #define AB8500_WD_KICK_DELAY_US 100 /* usec */
 #define AB8500_WD_V11_DISABLE_DELAY_US 100 /* usec */
@@ -113,68 +104,6 @@ enum ab8505_usb_link_status {
 	USB_LINK_MOTOROLA_FACTORY_CBL_PHY_EN_8505,
 };
 
-enum ab8540_usb_link_status {
-	USB_LINK_NOT_CONFIGURED_8540 = 0,
-	USB_LINK_STD_HOST_NC_8540,
-	USB_LINK_STD_HOST_C_NS_8540,
-	USB_LINK_STD_HOST_C_S_8540,
-	USB_LINK_CDP_8540,
-	USB_LINK_RESERVED0_8540,
-	USB_LINK_RESERVED1_8540,
-	USB_LINK_DEDICATED_CHG_8540,
-	USB_LINK_ACA_RID_A_8540,
-	USB_LINK_ACA_RID_B_8540,
-	USB_LINK_ACA_RID_C_NM_8540,
-	USB_LINK_RESERVED2_8540,
-	USB_LINK_RESERVED3_8540,
-	USB_LINK_HM_IDGND_8540,
-	USB_LINK_CHARGERPORT_NOT_OK_8540,
-	USB_LINK_CHARGER_DM_HIGH_8540,
-	USB_LINK_PHYEN_NO_VBUS_NO_IDGND_8540,
-	USB_LINK_STD_UPSTREAM_NO_IDGNG_VBUS_8540,
-	USB_LINK_STD_UPSTREAM_8540,
-	USB_LINK_CHARGER_SE1_8540,
-	USB_LINK_CARKIT_CHGR_1_8540,
-	USB_LINK_CARKIT_CHGR_2_8540,
-	USB_LINK_ACA_DOCK_CHGR_8540,
-	USB_LINK_SAMSUNG_BOOT_CBL_PHY_EN_8540,
-	USB_LINK_SAMSUNG_BOOT_CBL_PHY_DISB_8540,
-	USB_LINK_SAMSUNG_UART_CBL_PHY_EN_8540,
-	USB_LINK_SAMSUNG_UART_CBL_PHY_DISB_8540,
-	USB_LINK_MOTOROLA_FACTORY_CBL_PHY_EN_8540
-};
-
-enum ab9540_usb_link_status {
-	USB_LINK_NOT_CONFIGURED_9540 = 0,
-	USB_LINK_STD_HOST_NC_9540,
-	USB_LINK_STD_HOST_C_NS_9540,
-	USB_LINK_STD_HOST_C_S_9540,
-	USB_LINK_CDP_9540,
-	USB_LINK_RESERVED0_9540,
-	USB_LINK_RESERVED1_9540,
-	USB_LINK_DEDICATED_CHG_9540,
-	USB_LINK_ACA_RID_A_9540,
-	USB_LINK_ACA_RID_B_9540,
-	USB_LINK_ACA_RID_C_NM_9540,
-	USB_LINK_RESERVED2_9540,
-	USB_LINK_RESERVED3_9540,
-	USB_LINK_HM_IDGND_9540,
-	USB_LINK_CHARGERPORT_NOT_OK_9540,
-	USB_LINK_CHARGER_DM_HIGH_9540,
-	USB_LINK_PHYEN_NO_VBUS_NO_IDGND_9540,
-	USB_LINK_STD_UPSTREAM_NO_IDGNG_VBUS_9540,
-	USB_LINK_STD_UPSTREAM_9540,
-	USB_LINK_CHARGER_SE1_9540,
-	USB_LINK_CARKIT_CHGR_1_9540,
-	USB_LINK_CARKIT_CHGR_2_9540,
-	USB_LINK_ACA_DOCK_CHGR_9540,
-	USB_LINK_SAMSUNG_BOOT_CBL_PHY_EN_9540,
-	USB_LINK_SAMSUNG_BOOT_CBL_PHY_DISB_9540,
-	USB_LINK_SAMSUNG_UART_CBL_PHY_EN_9540,
-	USB_LINK_SAMSUNG_UART_CBL_PHY_DISB_9540,
-	USB_LINK_MOTOROLA_FACTORY_CBL_PHY_EN_9540
-};
-
 enum ab8500_usb_mode {
 	USB_IDLE = 0,
 	USB_PERIPHERAL,
@@ -192,10 +121,6 @@ enum ab8500_usb_mode {
 #define AB8500_USB_FLAG_USE_AB_IDDET		(1 << 3)
 /* Enable setting regulators voltage */
 #define AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE	(1 << 4)
-/* Enable the check_vbus_status workaround */
-#define AB8500_USB_FLAG_USE_CHECK_VBUS_STATUS	(1 << 5)
-/* Enable the vbus host workaround */
-#define AB8500_USB_FLAG_USE_VBUS_HOST_QUIRK	(1 << 6)
 
 struct ab8500_usb {
 	struct usb_phy phy;
@@ -203,7 +128,6 @@ struct ab8500_usb {
 	struct ab8500 *ab8500;
 	unsigned vbus_draw;
 	struct work_struct phy_dis_work;
-	struct work_struct vbus_event_work;
 	enum ab8500_usb_mode mode;
 	struct clk *sysclk;
 	struct regulator *v_ape;
@@ -342,15 +266,6 @@ static void ab8500_usb_phy_enable(struct ab8500_usb *ab, bool sel_host)
 	abx500_mask_and_set_register_interruptible(ab->dev,
 			AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 			bit, bit);
-
-	if (ab->flags & AB8500_USB_FLAG_USE_VBUS_HOST_QUIRK) {
-		if (sel_host)
-			abx500_set_register_interruptible(ab->dev,
-					AB8500_USB, AB8540_USB_OTG_CTL_REG,
-					AB8540_BIT_OTG_CTL_VBUS_VALID_ENA |
-					AB8540_BIT_OTG_CTL_ID_HOST_ENA |
-					AB8540_BIT_OTG_CTL_ID_DEV_ENA);
-	}
 }
 
 static void ab8500_usb_phy_disable(struct ab8500_usb *ab, bool sel_host)
@@ -395,263 +310,6 @@ static void ab8500_usb_phy_disable(struct ab8500_usb *ab, bool sel_host)
 #define ab8500_usb_peri_phy_en(ab)	ab8500_usb_phy_enable(ab, false)
 #define ab8500_usb_peri_phy_dis(ab)	ab8500_usb_phy_disable(ab, false)
 
-static int ab9540_usb_link_status_update(struct ab8500_usb *ab,
-		enum ab9540_usb_link_status lsts)
-{
-	enum ux500_musb_vbus_id_status event = 0;
-
-	dev_dbg(ab->dev, "ab9540_usb_link_status_update %d\n", lsts);
-
-	if (ab->previous_link_status_state == USB_LINK_HM_IDGND_9540 &&
-			(lsts == USB_LINK_STD_HOST_C_NS_9540 ||
-			 lsts == USB_LINK_STD_HOST_NC_9540))
-		return 0;
-
-	if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_9540 &&
-			(lsts == USB_LINK_STD_HOST_NC_9540))
-		return 0;
-
-	ab->previous_link_status_state = lsts;
-
-	switch (lsts) {
-	case USB_LINK_ACA_RID_B_9540:
-		event = UX500_MUSB_RIDB;
-	case USB_LINK_NOT_CONFIGURED_9540:
-	case USB_LINK_RESERVED0_9540:
-	case USB_LINK_RESERVED1_9540:
-	case USB_LINK_RESERVED2_9540:
-	case USB_LINK_RESERVED3_9540:
-		if (ab->mode == USB_PERIPHERAL)
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					UX500_MUSB_CLEAN, &ab->vbus_draw);
-		ab->mode = USB_IDLE;
-		ab->phy.otg->default_a = false;
-		ab->vbus_draw = 0;
-		if (event != UX500_MUSB_RIDB)
-			event = UX500_MUSB_NONE;
-		/* Fallback to default B_IDLE as nothing is connected. */
-		ab->phy.otg->state = OTG_STATE_B_IDLE;
-		usb_phy_set_event(&ab->phy, USB_EVENT_NONE);
-		break;
-
-	case USB_LINK_ACA_RID_C_NM_9540:
-		event = UX500_MUSB_RIDC;
-	case USB_LINK_STD_HOST_NC_9540:
-	case USB_LINK_STD_HOST_C_NS_9540:
-	case USB_LINK_STD_HOST_C_S_9540:
-	case USB_LINK_CDP_9540:
-		if (ab->mode == USB_HOST) {
-			ab->mode = USB_PERIPHERAL;
-			ab8500_usb_host_phy_dis(ab);
-			ab8500_usb_peri_phy_en(ab);
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					UX500_MUSB_PREPARE, &ab->vbus_draw);
-			usb_phy_set_event(&ab->phy, USB_EVENT_ENUMERATED);
-		}
-		if (ab->mode == USB_IDLE) {
-			ab->mode = USB_PERIPHERAL;
-			ab8500_usb_peri_phy_en(ab);
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					UX500_MUSB_PREPARE, &ab->vbus_draw);
-			usb_phy_set_event(&ab->phy, USB_EVENT_ENUMERATED);
-		}
-		if (event != UX500_MUSB_RIDC)
-			event = UX500_MUSB_VBUS;
-		break;
-
-	case USB_LINK_ACA_RID_A_9540:
-		event = UX500_MUSB_RIDA;
-	case USB_LINK_HM_IDGND_9540:
-	case USB_LINK_STD_UPSTREAM_9540:
-		if (ab->mode == USB_PERIPHERAL) {
-			ab->mode = USB_HOST;
-			ab8500_usb_peri_phy_dis(ab);
-			ab8500_usb_host_phy_en(ab);
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					UX500_MUSB_PREPARE, &ab->vbus_draw);
-		}
-		if (ab->mode == USB_IDLE) {
-			ab->mode = USB_HOST;
-			ab8500_usb_host_phy_en(ab);
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					UX500_MUSB_PREPARE, &ab->vbus_draw);
-		}
-		ab->phy.otg->default_a = true;
-		if (event != UX500_MUSB_RIDA)
-			event = UX500_MUSB_ID;
-
-		atomic_notifier_call_chain(&ab->phy.notifier,
-				event, &ab->vbus_draw);
-		break;
-
-	case USB_LINK_DEDICATED_CHG_9540:
-		ab->mode = USB_DEDICATED_CHG;
-		event = UX500_MUSB_CHARGER;
-		atomic_notifier_call_chain(&ab->phy.notifier,
-				event, &ab->vbus_draw);
-		usb_phy_set_event(&ab->phy, USB_EVENT_CHARGER);
-		break;
-
-	case USB_LINK_PHYEN_NO_VBUS_NO_IDGND_9540:
-	case USB_LINK_STD_UPSTREAM_NO_IDGNG_VBUS_9540:
-		if (!(is_ab9540_2p0_or_earlier(ab->ab8500))) {
-			event = UX500_MUSB_NONE;
-			if (ab->mode == USB_HOST) {
-				ab->phy.otg->default_a = false;
-				ab->vbus_draw = 0;
-				atomic_notifier_call_chain(&ab->phy.notifier,
-						event, &ab->vbus_draw);
-				ab8500_usb_host_phy_dis(ab);
-				ab->mode = USB_IDLE;
-			}
-			if (ab->mode == USB_PERIPHERAL) {
-				atomic_notifier_call_chain(&ab->phy.notifier,
-						event, &ab->vbus_draw);
-				ab8500_usb_peri_phy_dis(ab);
-				atomic_notifier_call_chain(&ab->phy.notifier,
-						UX500_MUSB_CLEAN,
-						&ab->vbus_draw);
-				ab->mode = USB_IDLE;
-				ab->phy.otg->default_a = false;
-				ab->vbus_draw = 0;
-				usb_phy_set_event(&ab->phy, USB_EVENT_NONE);
-			}
-		}
-		break;
-
-	default:
-		break;
-	}
-
-	return 0;
-}
-
-static int ab8540_usb_link_status_update(struct ab8500_usb *ab,
-		enum ab8540_usb_link_status lsts)
-{
-	enum ux500_musb_vbus_id_status event = 0;
-
-	dev_dbg(ab->dev, "ab8540_usb_link_status_update %d\n", lsts);
-
-	if (ab->enabled_charging_detection) {
-		/* Disable USB Charger detection */
-		abx500_mask_and_set_register_interruptible(ab->dev,
-				AB8500_USB, AB8540_VBUS_CTRL_REG,
-				AB8540_BIT_VBUS_CTRL_CHARG_DET_ENA, 0x00);
-		ab->enabled_charging_detection = false;
-	}
-
-	/*
-	 * Spurious link_status interrupts are seen in case of a
-	 * disconnection of a device in IDGND and RIDA stage
-	 */
-	if (ab->previous_link_status_state == USB_LINK_HM_IDGND_8540 &&
-			(lsts == USB_LINK_STD_HOST_C_NS_8540 ||
-			 lsts == USB_LINK_STD_HOST_NC_8540))
-		return 0;
-
-	if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_8540 &&
-			(lsts == USB_LINK_STD_HOST_NC_8540))
-		return 0;
-
-	ab->previous_link_status_state = lsts;
-
-	switch (lsts) {
-	case USB_LINK_ACA_RID_B_8540:
-		event = UX500_MUSB_RIDB;
-	case USB_LINK_NOT_CONFIGURED_8540:
-	case USB_LINK_RESERVED0_8540:
-	case USB_LINK_RESERVED1_8540:
-	case USB_LINK_RESERVED2_8540:
-	case USB_LINK_RESERVED3_8540:
-		ab->mode = USB_IDLE;
-		ab->phy.otg->default_a = false;
-		ab->vbus_draw = 0;
-		if (event != UX500_MUSB_RIDB)
-			event = UX500_MUSB_NONE;
-		/*
-		 * Fallback to default B_IDLE as nothing
-		 * is connected
-		 */
-		ab->phy.otg->state = OTG_STATE_B_IDLE;
-		usb_phy_set_event(&ab->phy, USB_EVENT_NONE);
-		break;
-
-	case USB_LINK_ACA_RID_C_NM_8540:
-		event = UX500_MUSB_RIDC;
-	case USB_LINK_STD_HOST_NC_8540:
-	case USB_LINK_STD_HOST_C_NS_8540:
-	case USB_LINK_STD_HOST_C_S_8540:
-	case USB_LINK_CDP_8540:
-		if (ab->mode == USB_IDLE) {
-			ab->mode = USB_PERIPHERAL;
-			ab8500_usb_peri_phy_en(ab);
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					UX500_MUSB_PREPARE, &ab->vbus_draw);
-			usb_phy_set_event(&ab->phy, USB_EVENT_ENUMERATED);
-		}
-		if (event != UX500_MUSB_RIDC)
-			event = UX500_MUSB_VBUS;
-		break;
-
-	case USB_LINK_ACA_RID_A_8540:
-	case USB_LINK_ACA_DOCK_CHGR_8540:
-		event = UX500_MUSB_RIDA;
-	case USB_LINK_HM_IDGND_8540:
-	case USB_LINK_STD_UPSTREAM_8540:
-		if (ab->mode == USB_IDLE) {
-			ab->mode = USB_HOST;
-			ab8500_usb_host_phy_en(ab);
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					UX500_MUSB_PREPARE, &ab->vbus_draw);
-		}
-		ab->phy.otg->default_a = true;
-		if (event != UX500_MUSB_RIDA)
-			event = UX500_MUSB_ID;
-		atomic_notifier_call_chain(&ab->phy.notifier,
-				event, &ab->vbus_draw);
-		break;
-
-	case USB_LINK_DEDICATED_CHG_8540:
-		ab->mode = USB_DEDICATED_CHG;
-		event = UX500_MUSB_CHARGER;
-		atomic_notifier_call_chain(&ab->phy.notifier,
-				event, &ab->vbus_draw);
-		usb_phy_set_event(&ab->phy, USB_EVENT_CHARGER);
-		break;
-
-	case USB_LINK_PHYEN_NO_VBUS_NO_IDGND_8540:
-	case USB_LINK_STD_UPSTREAM_NO_IDGNG_VBUS_8540:
-		event = UX500_MUSB_NONE;
-		if (ab->mode == USB_HOST) {
-			ab->phy.otg->default_a = false;
-			ab->vbus_draw = 0;
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					event, &ab->vbus_draw);
-			ab8500_usb_host_phy_dis(ab);
-			ab->mode = USB_IDLE;
-		}
-		if (ab->mode == USB_PERIPHERAL) {
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					event, &ab->vbus_draw);
-			ab8500_usb_peri_phy_dis(ab);
-			atomic_notifier_call_chain(&ab->phy.notifier,
-					UX500_MUSB_CLEAN, &ab->vbus_draw);
-			ab->mode = USB_IDLE;
-			ab->phy.otg->default_a = false;
-			ab->vbus_draw = 0;
-		usb_phy_set_event(&ab->phy, USB_EVENT_NONE);
-		}
-		break;
-
-	default:
-		event = UX500_MUSB_NONE;
-		break;
-	}
-
-	return 0;
-}
-
 static int ab8505_usb_link_status_update(struct ab8500_usb *ab,
 		enum ab8505_usb_link_status lsts)
 {
@@ -858,20 +516,6 @@ static int abx500_usb_link_status_update(struct ab8500_usb *ab)
 				AB8500_USB, AB8505_USB_LINE_STAT_REG, &reg);
 		lsts = (reg >> 3) & 0x1F;
 		ret = ab8505_usb_link_status_update(ab, lsts);
-	} else if (is_ab8540(ab->ab8500)) {
-		enum ab8540_usb_link_status lsts;
-
-		abx500_get_register_interruptible(ab->dev,
-				AB8500_USB, AB8540_USB_LINK_STAT_REG, &reg);
-		lsts = (reg >> 3) & 0xFF;
-		ret = ab8540_usb_link_status_update(ab, lsts);
-	} else if (is_ab9540(ab->ab8500)) {
-		enum ab9540_usb_link_status lsts;
-
-		abx500_get_register_interruptible(ab->dev,
-				AB8500_USB, AB9540_USB_LINK_STAT_REG, &reg);
-		lsts = (reg >> 3) & 0xFF;
-		ret = ab9540_usb_link_status_update(ab, lsts);
 	}
 
 	return ret;
@@ -946,69 +590,6 @@ static void ab8500_usb_phy_disable_work(struct work_struct *work)
 		ab8500_usb_peri_phy_dis(ab);
 }
 
-/* Check if VBUS is set and linkstatus has not detected a cable. */
-static bool ab8500_usb_check_vbus_status(struct ab8500_usb *ab)
-{
-	u8 isource2;
-	u8 reg;
-	enum ab8540_usb_link_status lsts;
-
-	abx500_get_register_interruptible(ab->dev,
-			AB8500_INTERRUPT, AB8500_IT_SOURCE2_REG,
-			&isource2);
-
-	/* If Vbus is below 3.6V abort */
-	if (!(isource2 & AB8500_BIT_SOURCE2_VBUSDET))
-		return false;
-
-	abx500_get_register_interruptible(ab->dev,
-			AB8500_USB, AB8540_USB_LINK_STAT_REG,
-			&reg);
-
-	lsts = (reg >> 3) & 0xFF;
-
-	/* Check if linkstatus has detected a cable */
-	if (lsts)
-		return false;
-
-	return true;
-}
-
-/* re-trigger charger detection again with watchdog re-kick. */
-static void ab8500_usb_vbus_turn_on_event_work(struct work_struct *work)
-{
-	struct ab8500_usb *ab = container_of(work, struct ab8500_usb,
-			vbus_event_work);
-
-	if (ab->mode != USB_IDLE)
-		return;
-
-	abx500_set_register_interruptible(ab->dev,
-			AB8500_SYS_CTRL2_BLOCK, AB8500_MAIN_WD_CTRL_REG,
-			AB8500_BIT_WD_CTRL_ENABLE);
-
-	udelay(100);
-
-	abx500_set_register_interruptible(ab->dev,
-			AB8500_SYS_CTRL2_BLOCK, AB8500_MAIN_WD_CTRL_REG,
-			AB8500_BIT_WD_CTRL_ENABLE | AB8500_BIT_WD_CTRL_KICK);
-
-	udelay(100);
-
-	/* Disable Main watchdog */
-	abx500_set_register_interruptible(ab->dev,
-			AB8500_SYS_CTRL2_BLOCK, AB8500_MAIN_WD_CTRL_REG,
-			0x0);
-
-	/* Enable USB Charger detection */
-	abx500_mask_and_set_register_interruptible(ab->dev,
-			AB8500_USB, AB8540_VBUS_CTRL_REG,
-			AB8540_BIT_VBUS_CTRL_CHARG_DET_ENA,
-			AB8540_BIT_VBUS_CTRL_CHARG_DET_ENA);
-
-	ab->enabled_charging_detection = true;
-}
-
 static int ab8500_usb_set_suspend(struct usb_phy *x, int suspend)
 {
 	/* TODO */
@@ -1256,66 +837,6 @@ static void ab8500_usb_set_ab8505_tuning_values(struct ab8500_usb *ab)
 				err);
 }
 
-static void ab8500_usb_set_ab8540_tuning_values(struct ab8500_usb *ab)
-{
-	int err;
-
-	err = abx500_set_register_interruptible(ab->dev,
-			AB8540_DEBUG, AB8500_USB_PHY_TUNE1, 0xCC);
-	if (err < 0)
-		dev_err(ab->dev, "Failed to set PHY_TUNE1 register ret=%d\n",
-				err);
-
-	err = abx500_set_register_interruptible(ab->dev,
-			AB8540_DEBUG, AB8500_USB_PHY_TUNE2, 0x60);
-	if (err < 0)
-		dev_err(ab->dev, "Failed to set PHY_TUNE2 register ret=%d\n",
-				err);
-
-	err = abx500_set_register_interruptible(ab->dev,
-			AB8540_DEBUG, AB8500_USB_PHY_TUNE3, 0x90);
-	if (err < 0)
-		dev_err(ab->dev, "Failed to set PHY_TUNE3 register ret=%d\n",
-				err);
-}
-
-static void ab8500_usb_set_ab9540_tuning_values(struct ab8500_usb *ab)
-{
-	int err;
-
-	/* Enable the PBT/Bank 0x12 access */
-	err = abx500_set_register_interruptible(ab->dev,
-			AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x01);
-	if (err < 0)
-		dev_err(ab->dev, "Failed to enable bank12 access err=%d\n",
-				err);
-
-	err = abx500_set_register_interruptible(ab->dev,
-			AB8500_DEBUG, AB8500_USB_PHY_TUNE1, 0xC8);
-	if (err < 0)
-		dev_err(ab->dev, "Failed to set PHY_TUNE1 register err=%d\n",
-				err);
-
-	err = abx500_set_register_interruptible(ab->dev,
-			AB8500_DEBUG, AB8500_USB_PHY_TUNE2, 0x60);
-	if (err < 0)
-		dev_err(ab->dev, "Failed to set PHY_TUNE2 register err=%d\n",
-				err);
-
-	err = abx500_set_register_interruptible(ab->dev,
-			AB8500_DEBUG, AB8500_USB_PHY_TUNE3, 0x80);
-	if (err < 0)
-		dev_err(ab->dev, "Failed to set PHY_TUNE3 register err=%d\n",
-				err);
-
-	/* Switch to normal mode/disable Bank 0x12 access */
-	err = abx500_set_register_interruptible(ab->dev,
-			AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x00);
-	if (err < 0)
-		dev_err(ab->dev, "Failed to switch bank12 access err=%d\n",
-				err);
-}
-
 static int ab8500_usb_probe(struct platform_device *pdev)
 {
 	struct ab8500_usb	*ab;
@@ -1362,17 +883,6 @@ static int ab8500_usb_probe(struct platform_device *pdev)
 			AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ |
 			AB8500_USB_FLAG_USE_VBUS_DET_IRQ |
 			AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE;
-	} else if (is_ab8540(ab->ab8500)) {
-		ab->flags |= AB8500_USB_FLAG_USE_LINK_STATUS_IRQ |
-			AB8500_USB_FLAG_USE_CHECK_VBUS_STATUS |
-			AB8500_USB_FLAG_USE_VBUS_HOST_QUIRK |
-			AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE;
-	} else if (is_ab9540(ab->ab8500)) {
-		ab->flags |= AB8500_USB_FLAG_USE_LINK_STATUS_IRQ |
-			AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE;
-		if (is_ab9540_2p0_or_earlier(ab->ab8500))
-			ab->flags |= AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ |
-				AB8500_USB_FLAG_USE_VBUS_DET_IRQ;
 	}
 
 	/* Disable regulator voltage setting for AB8500 <= v2.0 */
@@ -1384,8 +894,6 @@ static int ab8500_usb_probe(struct platform_device *pdev)
 	/* all: Disable phy when called from set_host and set_peripheral */
 	INIT_WORK(&ab->phy_dis_work, ab8500_usb_phy_disable_work);
 
-	INIT_WORK(&ab->vbus_event_work, ab8500_usb_vbus_turn_on_event_work);
-
 	err = ab8500_usb_regulator_get(ab);
 	if (err)
 		return err;
@@ -1412,12 +920,6 @@ static int ab8500_usb_probe(struct platform_device *pdev)
 	else if (is_ab8505(ab->ab8500))
 		/* Phy tuning values for AB8505 */
 		ab8500_usb_set_ab8505_tuning_values(ab);
-	else if (is_ab8540(ab->ab8500))
-		/* Phy tuning values for AB8540 */
-		ab8500_usb_set_ab8540_tuning_values(ab);
-	else if (is_ab9540(ab->ab8500))
-		/* Phy tuning values for AB9540 */
-		ab8500_usb_set_ab9540_tuning_values(ab);
 
 	/* Needed to enable ID detection. */
 	ab8500_usb_wd_workaround(ab);
@@ -1428,11 +930,6 @@ static int ab8500_usb_probe(struct platform_device *pdev)
 	 */
 	ab8500_usb_restart_phy(ab);
 
-	if (ab->flags & AB8500_USB_FLAG_USE_CHECK_VBUS_STATUS) {
-		if (ab8500_usb_check_vbus_status(ab))
-			schedule_work(&ab->vbus_event_work);
-	}
-
 	abx500_usb_link_status_update(ab);
 
 	dev_info(&pdev->dev, "revision 0x%2x driver initialized\n", rev);
@@ -1445,7 +942,6 @@ static int ab8500_usb_remove(struct platform_device *pdev)
 	struct ab8500_usb *ab = platform_get_drvdata(pdev);
 
 	cancel_work_sync(&ab->phy_dis_work);
-	cancel_work_sync(&ab->vbus_event_work);
 
 	usb_remove_phy(&ab->phy);
 
@@ -1459,8 +955,6 @@ static int ab8500_usb_remove(struct platform_device *pdev)
 
 static const struct platform_device_id ab8500_usb_devtype[] = {
 	{ .name = "ab8500-usb", },
-	{ .name = "ab8540-usb", },
-	{ .name = "ab9540-usb", },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(platform, ab8500_usb_devtype);