Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM device-tree updates from Olof Johansson:
 "Business as usual -- the bulk of our changes are to devicetree files
  with new hardware support, new SoCs and platforms, and new board
  types.

  New SoCs/platforms:
   - Raspberry Pi Compute Module (CM1) and IO board
   - i.MX6SSL from NXP
   - Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
     and PLC interfaces
   - TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
     controllers, communication and PRU subsystem and lots of other
     interfaces (PCIe, USB3, etc).

  New boards and systems:
   - Several Atmel at91-based boards from Laird
   - Marvell Armada388-based Helios4 board from SolidRun
   - Samsung Aires-based phones (s5pv210)
   - Allwinner A64-based Pinebook laptop

  In addition to the above, there's the usual amount of new devices
  described on existing platforms, fixes and tweaks and new minor
  variants of boards/platforms"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
  arm64: dts: sdm845: Add tsens nodes
  arm64: dts: msm8996: thermal: Initialise via DT and add second controller
  arm64: dts: sprd: Add one suspend timer
  arm64: dts: sprd: Add SC27XX ADC device
  arm64: dts: sprd: Add SC27XX eFuse device
  arm64: dts: sprd: Add SC27XX vibrator device
  arm64: dts: sprd: Add SC27XX breathing light controller device
  arm64: dts: meson-axg: add spdif-dit codec
  arm64: dts: meson-axg: add lineout codec
  arm64: dts: meson-axg: add linein codec
  arm64: dts: meson-axg: add tdm interfaces
  arm64: dts: meson-axg: add tdmout formatters
  arm64: dts: meson-axg: add tdmin formatters
  arm64: dts: meson-axg: add spdifout
  arm64: dts: rockchip: add led support for Firefly-RK3399
  arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
  arm64: dts: rockchip: add power button support for Firefly-RK3399
  ARM: dts: aspeed: Add coprocessor interrupt controller
  arm64: dts: meson-axg: add audio arb reset controller
  arm64: dts: meson-axg: add usb power regulator
  ...

Documentation/devicetree/bindings/arm/adapteva.txt

@@ -1,7 +0,0 @@
-Adapteva Platforms Device Tree Bindings
----------------------------------------
-
-Parallella board
-
-Required root node properties:
-    - compatible = "adapteva,parallella";

Documentation/devicetree/bindings/arm/amlogic.txt

@@ -41,6 +41,14 @@ Boards with the Amlogic Meson GXL S905D SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,s905d", "amlogic,meson-gxl";
 
+Boards with the Amlogic Meson GXL S805X SoC shall have the following properties:
+  Required root node property:
+    compatible: "amlogic,s805x", "amlogic,meson-gxl";
+
+Boards with the Amlogic Meson GXL S905W SoC shall have the following properties:
+  Required root node property:
+    compatible: "amlogic,s905w", "amlogic,meson-gxl";
+
 Boards with the Amlogic Meson GXM S912 SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,s912", "amlogic,meson-gxm";
@@ -79,6 +87,11 @@ Board compatible values (alphabetically, grouped by SoC):
   - "amlogic,p230" (Meson gxl s905d)
   - "amlogic,p231" (Meson gxl s905d)
 
+  - "amlogic,p241" (Meson gxl s805x)
+
+  - "amlogic,p281" (Meson gxl s905w)
+  - "oranth,tx3-mini" (Meson gxl s905w)
+
   - "amlogic,q200" (Meson gxm s912)
   - "amlogic,q201" (Meson gxm s912)
   - "khadas,vim2" (Meson gxm s912)

Documentation/devicetree/bindings/arm/atmel-pmc.txt

@@ -1,14 +0,0 @@
-* Power Management Controller (PMC)
-
-Required properties:
-- compatible: Should be "atmel,<chip>-pmc".
-	<chip> can be: at91rm9200, at91sam9260, at91sam9g45, at91sam9n12,
-	at91sam9x5, sama5d3
-
-- reg: Should contain PMC registers location and length
-
-Examples:
-	pmc: pmc@fffffc00 {
-		compatible = "atmel,at91rm9200-pmc";
-		reg = <0xfffffc00 0x100>;
-	};

Documentation/devicetree/bindings/arm/cpus.txt

@@ -183,6 +183,7 @@ described below.
 			    "marvell,sheeva-v5"
 			    "nvidia,tegra132-denver"
 			    "nvidia,tegra186-denver"
+			    "nvidia,tegra194-carmel"
 			    "qcom,krait"
 			    "qcom,kryo"
 			    "qcom,kryo385"
@@ -219,6 +220,7 @@ described below.
 			    "qcom,kpss-acc-v1"
 			    "qcom,kpss-acc-v2"
 			    "renesas,apmu"
+			    "renesas,r9a06g032-smp"
 			    "rockchip,rk3036-smp"
 			    "rockchip,rk3066-smp"
 			    "ste,dbx500-smp"

Documentation/devicetree/bindings/arm/freescale/m4if.txt

@@ -0,0 +1,12 @@
+* Freescale Multi Master Multi Memory Interface (M4IF) module
+
+Required properties:
+- compatible : Should be "fsl,imx51-m4if"
+- reg : Address and length of the register set for the device
+
+Example:
+
+m4if: m4if@83fd8000 {
+	compatible = "fsl,imx51-m4if";
+	reg = <0x83fd8000 0x1000>;
+};

Documentation/devicetree/bindings/arm/freescale/tigerp.txt

@@ -0,0 +1,12 @@
+* Freescale Tigerp platform module
+
+Required properties:
+- compatible : Should be "fsl,imx51-tigerp"
+- reg : Address and length of the register set for the device
+
+Example:
+
+tigerp: tigerp@83fa0000 {
+	compatible = "fsl,imx51-tigerp";
+	reg = <0x83fa0000 0x28>;
+};

Documentation/devicetree/bindings/arm/fsl.txt

@@ -53,6 +53,10 @@ i.MX6 Quad SABRE Automotive Board
 Required root node properties:
     - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
 
+i.MX6SLL EVK board
+Required root node properties:
+    - compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
+
 Generic i.MX boards
 -------------------
 

Documentation/devicetree/bindings/arm/insignal-boards.txt

@@ -1,8 +0,0 @@
-* Insignal's Exynos4210 based Origen evaluation board
-
-Origen low-cost evaluation board is based on Samsung's Exynos4210 SoC.
-
-Required root node properties:
-    - compatible = should be one or more of the following.
-        (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.
-        (b) "samsung,exynos4210"  - for boards based on Exynos4210 SoC.

Documentation/devicetree/bindings/arm/mediatek.txt

@@ -51,6 +51,9 @@ Supported boards:
 - Evaluation board for MT6797(Helio X20):
     Required root node properties:
       - compatible = "mediatek,mt6797-evb", "mediatek,mt6797";
+- Mediatek X20 Development Board:
+    Required root node properties:
+      - compatible = "archermind,mt6797-x20-dev", "mediatek,mt6797";
 - Reference board variant 1 for MT7622:
     Required root node properties:
       - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622";
@@ -63,9 +66,6 @@ Supported boards:
 - Reference board for MT7623n with eMMC:
     Required root node properties:
       - compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623";
-- Reference  board for MT7623n with NAND:
-    Required root node properties:
-      - compatible = "mediatek,mt7623n-rfb-nand", "mediatek,mt7623";
 - Bananapi BPI-R2 board:
       - compatible = "bananapi,bpi-r2", "mediatek,mt7623";
 - MTK mt8127 tablet moose EVB:

Documentation/devicetree/bindings/arm/omap/l4.txt

@@ -7,6 +7,7 @@ Required properties:
 	       Should be "ti,omap2-l4-wkup" for OMAP2 family l4 wkup bus
 	       Should be "ti,omap3-l4-core" for OMAP3 family l4 core bus
 	       Should be "ti,omap4-l4-cfg" for OMAP4 family l4 cfg bus
+	       Should be "ti,omap4-l4-per" for OMAP4 family l4 per bus
 	       Should be "ti,omap4-l4-wkup" for OMAP4 family l4 wkup bus
 	       Should be "ti,omap5-l4-cfg" for OMAP5 family l4 cfg bus
 	       Should be "ti,omap5-l4-wkup" for OMAP5 family l4 wkup bus
@@ -15,11 +16,21 @@ Required properties:
 	       Should be "ti,am3-l4-wkup" for AM33xx family l4 wkup bus
 	       Should be "ti,am4-l4-wkup" for AM43xx family l4 wkup bus
 - ranges : contains the IO map range for the bus
+- reg : registers link agent and interconnect agent and access protection
+- reg-names : "la" for link agent, "ia0" to "ia3" for one to three
+              interconnect agent instances, "ap" for access if it exists
 
 Examples:
 
-l4: l4@48000000 {
-	compatible "ti,omap2-l4", "simple-bus";
+l4: interconnect@48000000 {
+	compatible "ti,omap4-l4-per", "simple-bus";
+	reg = <0x48000000 0x800>,
+	      <0x48000800 0x800>,
+	      <0x48001000 0x400>,
+	      <0x48001400 0x400>,
+	      <0x48001800 0x400>,
+	      <0x48001c00 0x400>;
+	reg-names = "ap", "la", "ia0", "ia1", "ia2", "ia3";
 	#address-cells = <1>;
 	#size-cells = <1>;
 	ranges = <0 0x48000000 0x100000>;

Documentation/devicetree/bindings/arm/rockchip.txt

@@ -1,5 +1,10 @@
 Rockchip platforms device tree bindings
 ---------------------------------------
+
+- 96boards RK3399 Ficus (ROCK960 Enterprise Edition)
+    Required root node properties:
+      - compatible = "vamrs,ficus", "rockchip,rk3399";
+
 - Amarula Vyasa RK3288 board
     Required root node properties:
       - compatible = "amarula,vyasa-rk3288", "rockchip,rk3288";
@@ -66,6 +71,15 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "geekbuying,geekbox", "rockchip,rk3368";
 
+- Google Bob (Asus Chromebook Flip C101PA):
+    Required root node properties:
+	compatible = "google,bob-rev13", "google,bob-rev12",
+		     "google,bob-rev11", "google,bob-rev10",
+		     "google,bob-rev9", "google,bob-rev8",
+		     "google,bob-rev7", "google,bob-rev6",
+		     "google,bob-rev5", "google,bob-rev4",
+		     "google,bob", "google,gru", "rockchip,rk3399";
+
 - Google Brain (dev-board):
     Required root node properties:
       - compatible = "google,veyron-brain-rev0", "google,veyron-brain",

Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt

@@ -1,7 +1,10 @@
-* Samsung's Exynos SoC based boards
+* Samsung's Exynos and S5P SoC based boards
 
 Required root node properties:
     - compatible = should be one or more of the following.
+	- "samsung,aries"	- for S5PV210-based Samsung Aries board.
+	- "samsung,fascinate4g"	- for S5PV210-based Samsung Galaxy S Fascinate 4G (SGH-T959P) board.
+	- "samsung,galaxys"	- for S5PV210-based Samsung Galaxy S (i9000)  board.
 	- "samsung,artik5"	- for Exynos3250-based Samsung ARTIK5 module.
 	- "samsung,artik5-eval" - for Exynos3250-based Samsung ARTIK5 eval board.
 	- "samsung,monk"	- for Exynos3250-based Samsung Simband board.

Documentation/devicetree/bindings/arm/shmobile.txt

@@ -51,7 +51,8 @@ SoCs:
     compatible = "renesas,r8a77990"
   - R-Car D3 (R8A77995)
     compatible = "renesas,r8a77995"
-
+  - RZ/N1D (R9A06G032)
+    compatible = "renesas,r9a06g032"
 
 Boards:
 
@@ -112,6 +113,8 @@ Boards:
     compatible = "renesas,porter", "renesas,r8a7791"
   - RSKRZA1 (YR0K77210C000BE)
     compatible = "renesas,rskrza1", "renesas,r7s72100"
+  - RZN1D-DB (RZ/N1D Demo Board for the RZ/N1D 400 pins package)
+    compatible = "renesas,rzn1d400-db", "renesas,r9a06g032"
   - Salvator-X (RTP0RC7795SIPB0010S)
     compatible = "renesas,salvator-x", "renesas,r8a7795"
   - Salvator-X (RTP0RC7796SIPB0011S)

Documentation/devicetree/bindings/arm/ti/k3.txt

@@ -0,0 +1,23 @@
+Texas Instruments K3 Multicore SoC architecture device tree bindings
+--------------------------------------------------------------------
+
+Platforms based on Texas Instruments K3 Multicore SoC architecture
+shall follow the following scheme:
+
+SoCs
+----
+
+Each device tree root node must specify which exact SoC in K3 Multicore SoC
+architecture it uses, using one of the following compatible values:
+
+- AM654
+  compatible = "ti,am654";
+
+Boards
+------
+
+In addition, each device tree root node must specify which one or more
+of the following board-specific compatible values:
+
+- AM654 EVM
+  compatible = "ti,am654-evm", "ti,am654";

Documentation/devicetree/bindings/arm/xilinx.txt

@@ -8,18 +8,38 @@ Required root node properties:
 
 Additional compatible strings:
 
-- Xilinx internal board cc108
+- Adapteva Parallella board
+  "adapteva,parallella"
+
+- Avnet MicroZed board
+  "avnet,zynq-microzed"
+  "xlnx,zynq-microzed"
+
+- Avnet ZedBoard board
+  "avnet,zynq-zed"
+  "xlnx,zynq-zed"
+
+- Digilent Zybo board
+  "digilent,zynq-zybo"
+
+- Digilent Zybo Z7 board
+  "digilent,zynq-zybo-z7"
+
+- Xilinx CC108 internal board
   "xlnx,zynq-cc108"
 
-- Xilinx internal board zc770 with different FMC cards
+- Xilinx ZC702 internal board
+  "xlnx,zynq-zc702"
+
+- Xilinx ZC706 internal board
+  "xlnx,zynq-zc706"
+
+- Xilinx ZC770 internal board, with different FMC cards
   "xlnx,zynq-zc770-xm010"
   "xlnx,zynq-zc770-xm011"
   "xlnx,zynq-zc770-xm012"
   "xlnx,zynq-zc770-xm013"
 
-- Digilent Zybo Z7 board
-  "digilent,zynq-zybo-z7"
-
 ---------------------------------------------------------------
 
 Xilinx Zynq UltraScale+ MPSoC Platforms Device Tree Bindings

Documentation/devicetree/bindings/clock/at91-clock.txt

@@ -17,14 +17,13 @@ Required properties:
 	"atmel,at91sam9x5-clk-slow-rc-osc":
 		at91 internal slow RC oscillator
 
-	"atmel,at91rm9200-pmc" or
-	"atmel,at91sam9g45-pmc" or
-	"atmel,at91sam9n12-pmc" or
-	"atmel,at91sam9x5-pmc" or
-	"atmel,sama5d3-pmc":
+	"atmel,<chip>-pmc":
 		at91 PMC (Power Management Controller)
 		All at91 specific clocks (clocks defined below) must be child
 		node of the PMC node.
+		<chip> can be: at91rm9200, at91sam9260, at91sam9261,
+		at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9x5,
+		sama5d2, sama5d3 or sama5d4.
 
 	"atmel,at91sam9x5-clk-slow" (under sckc node)
 	or

Documentation/devicetree/bindings/iommu/mediatek,iommu.txt

@@ -40,6 +40,7 @@ video decode local arbiter, all these ports are according to the video HW.
 Required properties:
 - compatible : must be one of the following string:
 	"mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW.
+	"mediatek,mt2712-m4u" for mt2712 which uses generation two m4u HW.
 	"mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW.
 - reg : m4u register base and size.
 - interrupts : the interrupt of m4u.
@@ -50,8 +51,9 @@ Required properties:
 	according to the local arbiter index, like larb0, larb1, larb2...
 - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW.
 	Specifies the mtk_m4u_id as defined in
-	dt-binding/memory/mt2701-larb-port.h for mt2701 and
-	dt-binding/memory/mt8173-larb-port.h for mt8173
+	dt-binding/memory/mt2701-larb-port.h for mt2701,
+	dt-binding/memory/mt2712-larb-port.h for mt2712, and
+	dt-binding/memory/mt8173-larb-port.h for mt8173.
 
 Example:
 	iommu: iommu@10205000 {

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt

@@ -2,8 +2,9 @@ SMI (Smart Multimedia Interface) Common
 
 The hardware block diagram please check bindings/iommu/mediatek,iommu.txt
 
-Mediatek SMI have two generations of HW architecture, mt8173 uses the second
-generation of SMI HW while mt2701 uses the first generation HW of SMI.
+Mediatek SMI have two generations of HW architecture, mt2712 and mt8173 use
+the second generation of SMI HW while mt2701 uses the first generation HW of
+SMI.
 
 There's slight differences between the two SMI, for generation 2, the
 register which control the iommu port is at each larb's register base. But
@@ -15,6 +16,7 @@ not needed for SMI generation 2.
 Required properties:
 - compatible : must be one of :
 	"mediatek,mt2701-smi-common"
+	"mediatek,mt2712-smi-common"
 	"mediatek,mt8173-smi-common"
 - reg : the register and size of the SMI block.
 - power-domains : a phandle to the power domain of this local arbiter.

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt

@@ -4,8 +4,9 @@ The hardware block diagram please check bindings/iommu/mediatek,iommu.txt
 
 Required properties:
 - compatible : must be one of :
-		"mediatek,mt8173-smi-larb"
 		"mediatek,mt2701-smi-larb"
+		"mediatek,mt2712-smi-larb"
+		"mediatek,mt8173-smi-larb"
 - reg : the register and size of this local arbiter.
 - mediatek,smi : a phandle to the smi_common node.
 - power-domains : a phandle to the power domain of this local arbiter.
@@ -15,7 +16,7 @@ Required properties:
 	    the register.
   - "smi" : It's the clock for transfer data and command.
 
-Required property for mt2701:
+Required property for mt2701 and mt2712:
 - mediatek,larb-id :the hardware id of this larb.
 
 Example:

Documentation/devicetree/bindings/mmc/sunxi-mmc.txt

@@ -16,6 +16,8 @@ Required properties:
    * "allwinner,sun9i-a80-mmc"
    * "allwinner,sun50i-a64-emmc"
    * "allwinner,sun50i-a64-mmc"
+   * "allwinner,sun50i-h6-emmc", "allwinner.sun50i-a64-emmc"
+   * "allwinner,sun50i-h6-mmc", "allwinner.sun50i-a64-mmc"
  - reg : mmc controller base registers
  - clocks : a list with 4 phandle + clock specifier pairs
  - clock-names : must contain "ahb", "mmc", "output" and "sample"

Documentation/devicetree/bindings/net/dwmac-sun8i.txt

@@ -19,8 +19,6 @@ Required properties:
 - reset-names: must be "stmmaceth"
 - phy-mode: See ethernet.txt
 - phy-handle: See ethernet.txt
-- #address-cells: shall be 1
-- #size-cells: shall be 0
 - syscon: A phandle to the device containing the EMAC or GMAC clock register
 
 Optional properties:
@@ -86,8 +84,6 @@ emac: ethernet@1c0b000 {
 	reset-names = "stmmaceth";
 	clocks = <&ccu CLK_BUS_EMAC>;
 	clock-names = "stmmaceth";
-	#address-cells = <1>;
-	#size-cells = <0>;
 
 	phy-handle = <&int_mii_phy>;
 	phy-mode = "mii";
@@ -137,8 +133,6 @@ emac: ethernet@1c0b000 {
 	reset-names = "stmmaceth";
 	clocks = <&ccu CLK_BUS_EMAC>;
 	clock-names = "stmmaceth";
-	#address-cells = <1>;
-	#size-cells = <0>;
 
 	phy-handle = <&ext_rgmii_phy>;
 	phy-mode = "rgmii";
@@ -191,8 +185,6 @@ emac: ethernet@1c0b000 {
 	reset-names = "stmmaceth";
 	clocks = <&ccu CLK_BUS_EMAC>;
 	clock-names = "stmmaceth";
-	#address-cells = <1>;
-	#size-cells = <0>;
 
 	phy-handle = <&ext_rgmii_phy>;
 	phy-mode = "rgmii";

Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt

@@ -17,20 +17,18 @@ Example:
 
 	/* upstream device */
 
-	ssp0: ssp@41000000 {
+	ssp1: ssp@41000000 {
 		compatible = "mrvl,pxa3xx-ssp";
 		reg = <0x41000000 0x40>;
 		interrupts = <24>;
 		clock-names = "pxa27x-ssp.0";
-		dmas = <&dma 13
-			&dma 14>;
-		dma-names = "rx", "tx";
 	};
 
 	/* DAI as user */
 
 	ssp_dai0: ssp_dai@0 {
 		compatible = "mrvl,pxa-ssp-dai";
-		port = <&ssp0>;
+		port = <&ssp1>;
+		#sound-dai-cells = <0>;
 	};
 

Documentation/devicetree/bindings/timer/ti,davinci-timer.txt

@@ -0,0 +1,37 @@
+* Device tree bindings for Texas Instruments DaVinci timer
+
+This document provides bindings for the 64-bit timer in the DaVinci
+architecture devices. The timer can be configured as a general-purpose 64-bit
+timer, dual general-purpose 32-bit timers. When configured as dual 32-bit
+timers, each half can operate in conjunction (chain mode) or independently
+(unchained mode) of each other.
+
+The timer is a free running up-counter and can generate interrupts when the
+counter reaches preset counter values.
+
+Also see ../watchdog/davinci-wdt.txt for timers that are configurable as
+watchdog timers.
+
+Required properties:
+
+- compatible : should be "ti,da830-timer".
+- reg : specifies base physical address and count of the registers.
+- interrupts : interrupts generated by the timer.
+- interrupt-names: should be "tint12", "tint34", "cmpint0", "cmpint1",
+		   "cmpint2", "cmpint3", "cmpint4", "cmpint5", "cmpint6",
+		   "cmpint7" ("cmpintX" may be omitted if not present in the
+		   hardware).
+- clocks : the clock feeding the timer clock.
+
+Example:
+
+	clocksource: timer@20000 {
+		compatible = "ti,da830-timer";
+		reg = <0x20000 0x1000>;
+		interrupts = <21>, <22>, <74>, <75>, <76>, <77>, <78>, <79>,
+			     <80>, <81>;
+		interrupt-names = "tint12", "tint34", "cmpint0", "cmpint1",
+				  "cmpint2", "cmpint3", "cmpint4", "cmpint5",
+				  "cmpint6", "cmpint7";
+		clocks = <&pll0_auxclk>;
+	};

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -142,6 +142,7 @@ geekbuying	GeekBuying
 gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 geniatech	Geniatech, Inc.
+giantec	Giantec Semiconductor, Inc.
 giantplus	Giantplus Technology Co., Ltd.
 globalscale	Globalscale Technologies, Inc.
 gmt	Global Mixed-mode Technology, Inc.
@@ -200,6 +201,7 @@ koe	Kaohsiung Opto-Electronics Inc.
 kosagi	Sutajio Ko-Usagi PTE Ltd.
 kyo	Kyocera Corporation
 lacie	LaCie
+laird	Laird PLC
 lantiq	Lantiq Semiconductor
 lattice	Lattice Semiconductor
 lego	LEGO Systems A/S
@@ -279,6 +281,7 @@ opalkelly	Opal Kelly Incorporated
 opencores	OpenCores.org
 openrisc	OpenRISC.io
 option	Option NV
+oranth	Shenzhen Oranth Technology Co., Ltd.
 ORCL	Oracle Corporation
 orisetech	Orise Technology
 ortustech	Ortus Technology Co., Ltd.
@@ -322,6 +325,7 @@ rohm	ROHM Semiconductor Co., Ltd
 roofull	Shenzhen Roofull Technology Co, Ltd
 samsung	Samsung Semiconductor
 samtec	Samtec/Softing company
+sancloud	Sancloud Ltd
 sandisk	Sandisk Corporation
 sbs	Smart Battery System
 schindler	Schindler
@@ -401,6 +405,7 @@ upisemi	uPI Semiconductor Corp.
 urt	United Radiant Technology Corporation
 usi	Universal Scientific Industrial Co., Ltd.
 v3	V3 Semiconductor
+vamrs	Vamrs Ltd.
 variscite	Variscite Ltd.
 via	VIA Technologies, Inc.
 virtio	Virtual I/O Device Specification, developed by the OASIS consortium

MAINTAINERS

@@ -2014,6 +2014,7 @@ S:	Supported
 F:	arch/arm/boot/dts/emev2*
 F:	arch/arm/boot/dts/r7s*
 F:	arch/arm/boot/dts/r8a*
+F:	arch/arm/boot/dts/r9a*
 F:	arch/arm/boot/dts/sh*
 F:	arch/arm/configs/shmobile_defconfig
 F:	arch/arm/include/debug/renesas-scif.S
@@ -2132,6 +2133,15 @@ L:	linux-kernel@vger.kernel.org
 S:	Maintained
 F:	drivers/memory/*emif*
 
+ARM/TEXAS INSTRUMENTS K3 ARCHITECTURE
+M:	Tero Kristo <t-kristo@ti.com>
+M:	Nishanth Menon <nm@ti.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Supported
+F:	Documentation/devicetree/bindings/arm/ti/k3.txt
+F:	arch/arm64/boot/dts/ti/Makefile
+F:	arch/arm64/boot/dts/ti/k3-*
+
 ARM/TEXAS INSTRUMENT KEYSTONE ARCHITECTURE
 M:	Santosh Shilimkar <ssantosh@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)

arch/arm/boot/dts/Makefile

@@ -38,6 +38,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
 	at91-ariettag25.dtb \
 	at91-cosino_mega2560.dtb \
 	at91-kizboxmini.dtb \
+	at91-wb45n.dtb \
 	at91sam9g15ek.dtb \
 	at91sam9g25ek.dtb \
 	at91sam9g35ek.dtb \
@@ -50,7 +51,10 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
 	at91-sama5d2_ptc_ek.dtb \
 	at91-sama5d2_xplained.dtb \
 	at91-sama5d3_xplained.dtb \
+	at91-dvk_som60.dtb \
+	at91-gatwick.dtb \
 	at91-tse850-3.dtb \
+	at91-wb50n.dtb \
 	sama5d31ek.dtb \
 	sama5d33ek.dtb \
 	sama5d34ek.dtb \
@@ -73,6 +77,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2835-rpi-b-rev2.dtb \
 	bcm2835-rpi-b-plus.dtb \
 	bcm2835-rpi-a-plus.dtb \
+	bcm2835-rpi-cm1-io1.dtb \
 	bcm2836-rpi-2-b.dtb \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
@@ -200,6 +205,7 @@ dtb-$(CONFIG_ARCH_GEMINI) += \
 	gemini-dlink-dns-313.dtb \
 	gemini-nas4220b.dtb \
 	gemini-rut1xx.dtb \
+	gemini-sl93512r.dtb \
 	gemini-sq201.dtb \
 	gemini-wbd111.dtb \
 	gemini-wbd222.dtb
@@ -345,7 +351,8 @@ dtb-$(CONFIG_SOC_IMX27) += \
 	imx27-phytec-phycore-rdk.dtb \
 	imx27-phytec-phycard-s-rdk.dtb
 dtb-$(CONFIG_SOC_IMX31) += \
-	imx31-bug.dtb
+	imx31-bug.dtb \
+	imx31-lite.dtb
 dtb-$(CONFIG_SOC_IMX35) += \
 	imx35-eukrea-mbimxsd35-baseboard.dtb \
 	imx35-pdk.dtb
@@ -358,10 +365,14 @@ dtb-$(CONFIG_SOC_IMX51) += \
 	imx51-digi-connectcore-jsk.dtb \
 	imx51-eukrea-mbimxsd51-baseboard.dtb \
 	imx51-ts4800.dtb \
-	imx51-zii-rdu1.dtb
+	imx51-zii-rdu1.dtb \
+	imx51-zii-scu2-mezz.dtb \
+	imx51-zii-scu3-esb.dtb
 dtb-$(CONFIG_SOC_IMX53) += \
 	imx53-ard.dtb \
 	imx53-cx9020.dtb \
+	imx53-kp-ddc.dtb \
+	imx53-kp-hsc.dtb \
 	imx53-m53evk.dtb \
 	imx53-mba53.dtb \
 	imx53-ppd.dtb \
@@ -400,6 +411,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-hummingboard2-emmc-som-v15.dtb \
 	imx6dl-hummingboard2-som-v15.dtb \
 	imx6dl-icore.dtb \
+	imx6dl-icore-mipi.dtb \
 	imx6dl-icore-rqs.dtb \
 	imx6dl-mamoj.dtb \
 	imx6dl-nit6xlite.dtb \
@@ -521,6 +533,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 dtb-$(CONFIG_SOC_IMX6SL) += \
 	imx6sl-evk.dtb \
 	imx6sl-warp.dtb
+dtb-$(CONFIG_SOC_IMX6SLL) += \
+	imx6sll-evk.dtb
 dtb-$(CONFIG_SOC_IMX6SX) += \
 	imx6sx-nitrogen6sx.dtb \
 	imx6sx-sabreauto.dtb \
@@ -533,6 +547,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
 	imx6sx-udoo-neo-full.dtb
 dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-14x14-evk.dtb \
+	imx6ul-ccimx6ulsbcexpress.dtb \
 	imx6ul-geam.dtb \
 	imx6ul-isiot-emmc.dtb \
 	imx6ul-isiot-nand.dtb \
@@ -567,8 +582,10 @@ dtb-$(CONFIG_SOC_VF610) += \
 	vf610-cosmic.dtb \
 	vf610m4-cosmic.dtb \
 	vf610-twr.dtb \
+	vf610-zii-cfu1.dtb \
 	vf610-zii-dev-rev-b.dtb \
-	vf610-zii-dev-rev-c.dtb
+	vf610-zii-dev-rev-c.dtb \
+	vf610-zii-ssmb-spu3.dtb
 dtb-$(CONFIG_ARCH_MXS) += \
 	imx23-evk.dtb \
 	imx23-olinuxino.dtb \
@@ -695,10 +712,12 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-pepper.dtb \
 	am335x-phycore-rdk.dtb \
 	am335x-pocketbeagle.dtb \
+	am335x-sancloud-bbe.dtb \
 	am335x-shc.dtb \
 	am335x-sbc-t335.dtb \
 	am335x-sl50.dtb \
-	am335x-wega-rdk.dtb
+	am335x-wega-rdk.dtb \
+	am335x-osd3358-sm-red.dtb
 dtb-$(CONFIG_ARCH_OMAP4) += \
 	omap4-droid4-xt894.dtb \
 	omap4-duovero-parlor.dtb \
@@ -819,6 +838,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
 	r8a7793-gose.dtb \
 	r8a7794-alt.dtb \
 	r8a7794-silk.dtb \
+	r9a06g032-rzn1d400-db.dtb \
 	sh73a0-kzm9g.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rv1108-evb.dtb \
@@ -859,6 +879,8 @@ dtb-$(CONFIG_ARCH_S3C64XX) += \
 	s3c6410-smdk6410.dtb
 dtb-$(CONFIG_ARCH_S5PV210) += \
 	s5pv210-aquila.dtb \
+	s5pv210-fascinate4g.dtb \
+	s5pv210-galaxys.dtb \
 	s5pv210-goni.dtb \
 	s5pv210-smdkc110.dtb \
 	s5pv210-smdkv210.dtb \
@@ -1039,7 +1061,7 @@ dtb-$(CONFIG_ARCH_TANGO) += \
 	tango4-vantage-1172.dtb
 dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
 	tegra20-harmony.dtb \
-	tegra20-iris-512.dtb \
+	tegra20-colibri-iris.dtb \
 	tegra20-medcom-wide.dtb \
 	tegra20-paz00.dtb \
 	tegra20-plutux.dtb \
@@ -1109,6 +1131,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
 	zynq-zc770-xm012.dtb \
 	zynq-zc770-xm013.dtb \
 	zynq-zed.dtb \
+	zynq-zturn.dtb \
 	zynq-zybo.dtb \
 	zynq-zybo-z7.dtb
 dtb-$(CONFIG_MACH_ARMADA_370) += \
@@ -1138,6 +1161,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
 	armada-388-clearfog-pro.dtb \
 	armada-388-db.dtb \
 	armada-388-gp.dtb \
+	armada-388-helios4.dtb \
 	armada-388-rd.dtb
 dtb-$(CONFIG_MACH_ARMADA_39X) += \
 	armada-398-db.dtb
@@ -1168,7 +1192,6 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
 	mt7623a-rfb-emmc.dtb \
 	mt7623a-rfb-nand.dtb \
 	mt7623n-rfb-emmc.dtb \
-	mt7623n-rfb-nand.dtb \
 	mt7623n-bananapi-bpi-r2.dtb \
 	mt8127-moose.dtb \
 	mt8135-evbp1.dtb

arch/arm/boot/dts/am335x-baltos.dtsi

@@ -396,7 +396,7 @@
 		compatible = "ti,wl1835";
 		reg = <2>;
 		interrupt-parent = <&gpio3>;
-		interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <7 IRQ_TYPE_EDGE_RISING>;
 	};
 };
 

arch/arm/boot/dts/am335x-evm.dts

@@ -778,7 +778,7 @@
 		compatible = "ti,wl1835";
 		reg = <2>;
 		interrupt-parent = <&gpio3>;
-		interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <17 IRQ_TYPE_EDGE_RISING>;
 	};
 };
 

arch/arm/boot/dts/am335x-evmsk.dts

@@ -690,7 +690,7 @@
 		compatible = "ti,wl1271";
 		reg = <2>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <31 IRQ_TYPE_LEVEL_HIGH>; /* gpio 31 */
+		interrupts = <31 IRQ_TYPE_EDGE_RISING>; /* gpio 31 */
 		ref-clock-frequency = <38400000>;
 	};
 };

arch/arm/boot/dts/am335x-osd3358-sm-red.dts

@@ -0,0 +1,457 @@
+//SPDX-License-Identifier: GPL-2.0
+/* Copyright (C) 2018 Octavo Systems LLC - http://www.octavosystems.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-osd335x-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include <dt-bindings/display/tda998x.h>
+
+/ {
+	model = "Octavo Systems OSD3358-SM-RED";
+	compatible = "oct,osd3358-sm-refdesign", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+};
+
+&ldo3_reg {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins>;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&am33xx_pinmux {
+	nxp_hdmi_bonelt_pins: nxp-hdmi-bonelt-pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr0 */
+			AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data0.lcd_data0 */
+			AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data1.lcd_data1 */
+			AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data2.lcd_data2 */
+			AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0)		/* lcd_data3.lcd_data3 */
+			AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data4.lcd_data4 */
+			AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data5.lcd_data5 */
+			AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data6.lcd_data6 */
+			AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0)		/* lcd_data7.lcd_data7 */
+			AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data8.lcd_data8 */
+			AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data9.lcd_data9 */
+			AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data10.lcd_data10 */
+			AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0)		/* lcd_data11.lcd_data11 */
+			AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data12.lcd_data12 */
+			AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data13.lcd_data13 */
+			AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data14.lcd_data14 */
+			AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0)		/* lcd_data15.lcd_data15 */
+			AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_vsync.lcd_vsync */
+			AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_hsync.lcd_hsync */
+			AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_pclk.lcd_pclk */
+			AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_ac_bias_en.lcd_ac_bias_en */
+		>;
+	};
+
+	nxp_hdmi_bonelt_off_pins: nxp-hdmi-bonelt-off-pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr0 */
+		>;
+	};
+
+	mcasp0_pins: mcasp0-pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
+			AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
+			AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
+			AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
+			AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */
+		>;
+	};
+
+	flash_enable: flash-enable {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x944, PIN_OUTPUT_PULLDOWN | MUX_MODE7) 	/* rmii1_ref_clk.gpio0_29 */
+		>;
+	};
+
+	imu_interrupt: imu-interrupt {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) 		/* mii1_rx_er.gpio3_2 */
+		>;
+	};
+
+	ethernet_interrupt: ethernet-interrupt{
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE7) 		/* mii1_col.gpio3_0 */
+		>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+
+	/* If you want to get 24 bit RGB and 16 BGR mode instead of
+	 * current 16 bit RGB and 24 BGR modes, set the propety
+	 * below to "crossed" and uncomment the video-ports -property
+	 * in tda19988 node.
+	 * AM335x errata for wiring:
+	 * http://www.ti.com/lit/er/sprz360i/sprz360i.pdf
+	 */
+
+	blue-and-red-wiring = "straight";
+
+	port {
+		lcdc_0: endpoint {
+			remote-endpoint = <&hdmi_0>;
+		};
+	};
+};
+
+&i2c0 {
+	tda19988: hdmi-encoder@70 {
+		compatible = "nxp,tda998x";
+		reg = <0x70>;
+
+		pinctrl-names = "default", "off";
+		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+
+		/* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
+		/* video-ports = <0x234501>; */
+
+		#sound-dai-cells = <0>;
+		audio-ports = <	TDA998x_I2S	0x03>;
+
+		port {
+			hdmi_0: endpoint {
+				remote-endpoint = <&lcdc_0>;
+			};
+		};
+	};
+
+	mpu9250: imu@68 {
+		compatible = "invensense,mpu6050";
+		reg = <0x68>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <21 IRQ_TYPE_EDGE_RISING>;
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ax8975@c {
+				compatible = "ak,ak8975";
+				reg = <0x0c>;
+			};
+		};
+		/*invensense,int_config = <0x10>;
+		invensense,level_shifter = <0>;
+		invensense,orientation = [01 00 00 00 01 00 00 00 01];
+		invensense,sec_slave_type = <0>;
+		invensense,key = [4e cc 7e eb f6 1e 35 22 00 34 0d 65 32 e9 94 89];*/
+	};
+
+	bmp280: pressure@78 {
+		compatible = "bosch,bmp280";
+		reg = <0x76>;
+	};
+};
+
+&rtc {
+	system-power-controller;
+};
+
+&mcasp0 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp0_pins>;
+	status = "okay";
+	op-mode = <0>;	/* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 0
+		>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
+
+/ {
+	clk_mcasp0_fixed: clk-mcasp0-fixed {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24576000>;
+	};
+
+	clk_mcasp0: clk-mcasp0 {
+		#clock-cells = <0>;
+		compatible = "gpio-gate-clock";
+		clocks = <&clk_mcasp0_fixed>;
+		enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "TI BeagleBone Black";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink0_master>;
+		simple-audio-card,frame-master = <&dailink0_master>;
+
+		dailink0_master: simple-audio-card,cpu {
+			sound-dai = <&mcasp0>;
+			clocks = <&clk_mcasp0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&tda19988>;
+		};
+	};
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds_s0>;
+
+		compatible = "gpio-leds";
+
+		led2 {
+			label = "beaglebone:green:usr0";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led3 {
+			label = "beaglebone:green:usr1";
+			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led4 {
+			label = "beaglebone:green:usr2";
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu0";
+			default-state = "off";
+		};
+
+		led5 {
+			label = "beaglebone:green:usr3";
+			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+	};
+
+	vmmcsd_fixed: fixedregulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&clkout2_pin>;
+
+	user_leds_s0: user-leds-s0 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
+			AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_a6.gpio1_22 */
+			AM33XX_IOPAD(0x85c, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a7.gpio1_23 */
+			AM33XX_IOPAD(0x860, PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_a8.gpio1_24 */
+		>;
+	};
+
+	i2c2_pins: pinmux-i2c2-pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_ctsn.i2c2_sda */
+			AM33XX_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_rtsn.i2c2_scl */
+		>;
+	};
+
+	uart0_pins: pinmux-uart0-pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	clkout2_pin: pinmux-clkout2-pin {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr1.clkout2 */
+		>;
+	};
+
+	cpsw_default: cpsw-default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2)		/* mii1_rxdv.rgmii1_rctl */
+			AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd3.rgmii1_txd3 */
+			AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd2.rgmii1_txd2 */
+			AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd1.rgmii1_txd1 */
+			AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd0.rgmii1_txd0 */
+			AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txclk.rgmii1_txclk */
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2)		/* mii1_rxclk.rgmii1_rxclk */
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2)		/* mii1_rxd3.rgmii1_rxd3 */
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2)		/* mii1_rxd2.rgmii1_rxd2 */
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2)		/* mii1_rxd1.rgmii1_rxd1 */
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2)		/* mii1_rxd0.rgmii1_rxd0 */
+		>;
+	};
+
+	cpsw_sleep: cpsw-sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci-mdio-default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci-mdio-sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	mmc1_pins: pinmux-mmc1-pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* (C15) spi0_cs1.gpio0[6] */
+			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* (G16) mmc0_dat0.mmc0_dat0 */
+			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* (G15) mmc0_dat1.mmc0_dat1 */
+			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* (F18) mmc0_dat2.mmc0_dat2 */
+			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* (F17) mmc0_dat3.mmc0_dat3 */
+			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* (G18) mmc0_cmd.mmc0_cmd */
+			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* (G17) mmc0_clk.mmc0_clk */
+		>;
+	};
+
+	emmc_pins: pinmux-emmc-pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+			AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+			AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+			AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+			AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+			AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+			AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+			AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+			AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+			AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+		>;
+	};
+};
+
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	interrupts-extended = <&intc 18 &tps 0>;
+	interrupt-names = "mc", "vbus";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <4>;
+	phy-mode = "rgmii-txid";
+};
+
+&mac {
+	slaves = <1>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&mmc1 {
+	status = "okay";
+	bus-width = <0x4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+};
+
+&rtc {
+	clocks = <&clk_32768_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
+	clock-names = "ext-clk", "int-clk";
+};

arch/arm/boot/dts/am335x-sancloud-bbe.dts

@@ -0,0 +1,136 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "SanCloud BeagleBone Enhanced";
+	compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxdv.rgmii1_rctl */
+			AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd3.rgmii1_td3 */
+			AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd2.rgmii1_td2 */
+			AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd1.rgmii1_td1 */
+			AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd0.rgmii1_td0 */
+			AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txclk.rgmii1_tclk */
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxclk.rgmii1_rclk */
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd3.rgmii1_rd3 */
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd2.rgmii1_rd2 */
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd1.rgmii1_rd1 */
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd0.rgmii1_rd0 */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	usb_hub_ctrl: usb_hub_ctrl {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x944, PIN_OUTPUT_PULLUP | MUX_MODE7)     /* rmii1_refclk.gpio0_29 */
+		>;
+	};
+
+	mpu6050_pins: pinmux_mpu6050_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x968, PIN_INPUT | MUX_MODE7)    /* uart0_ctsn.gpio1_8 */
+		>;
+	};
+
+	lps3331ap_pins: pinmux_lps3331ap_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x868, PIN_INPUT | MUX_MODE7)     /* gpmc_a10.gpio1_26 */
+		>;
+	};
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "rgmii-txid";
+};
+
+&i2c0 {
+	lps331ap: barometer@5c {
+		compatible = "st,lps331ap-press";
+		st,drdy-int-pin = <1>;
+		reg = <0x5c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+	};
+
+	mpu6050: accelerometer@68 {
+		compatible = "invensense,mpu6050";
+		reg = <0x68>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+		orientation = <0xff 0 0 0 1 0 0 0 0xff>;
+	};
+
+	usb2512b: usb-hub@2c {
+		compatible = "microchip,usb2512b";
+		reg = <0x2c>;
+		reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		/* wifi on port 4 */
+	};
+};

arch/arm/boot/dts/am335x-sl50.dts

@@ -8,6 +8,8 @@
 /dts-v1/;
 
 #include "am33xx.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Toby Churchill SL50 Series";
@@ -34,25 +36,25 @@
 		pinctrl-0 = <&led_pins>;
 
 		led0 {
-			label = "sl50:green:usr0";
+			label = "sl50:red:usr0";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
 		led1 {
-			label = "sl50:red:usr1";
+			label = "sl50:green:usr1";
 			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
 		led2 {
-			label = "sl50:green:usr2";
+			label = "sl50:red:usr2";
 			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
 		led3 {
-			label = "sl50:red:usr3";
+			label = "sl50:green:usr3";
 			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
@@ -60,16 +62,44 @@
 
 	backlight0: disp0 {
 		compatible = "pwm-backlight";
-		pwms = <&ehrpwm1 0 500000 0>;
-		brightness-levels = <0 10 20 30 40 50 60 70 80 90 99>;
-		default-brightness-level = <6>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight0_pins>;
+		pwms = <&ehrpwm1 0 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
+				     10 11 12 13 14 15 16 17 18 19
+				     20 21 22 23 24 25 26 27 28 29
+				     30 31 32 33 34 35 36 37 38 39
+				     40 41 42 43 44 45 46 47 48 49
+				     50 51 52 53 54 55 56 57 58 59
+				     60 61 62 63 64 65 66 67 68 69
+				     70 71 72 73 74 75 76 77 78 79
+				     80 81 82 83 84 85 86 87 88 89
+				     90 91 92 93 94 95 96 97 98 99
+				    100>;
+		default-brightness-level = <50>;
+		enable-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_sys_reg>;
 	};
 
 	backlight1: disp1 {
 		compatible = "pwm-backlight";
-		pwms = <&ehrpwm1 1 500000 0>;
-		brightness-levels = <0 10 20 30 40 50 60 70 80 90 99>;
-		default-brightness-level = <6>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight1_pins>;
+		pwms = <&ehrpwm1 1 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
+				     10 11 12 13 14 15 16 17 18 19
+				     20 21 22 23 24 25 26 27 28 29
+				     30 31 32 33 34 35 36 37 38 39
+				     40 41 42 43 44 45 46 47 48 49
+				     50 51 52 53 54 55 56 57 58 59
+				     60 61 62 63 64 65 66 67 68 69
+				     70 71 72 73 74 75 76 77 78 79
+				     80 81 82 83 84 85 86 87 88 89
+				     90 91 92 93 94 95 96 97 98 99
+				    100>;
+		default-brightness-level = <50>;
+		enable-gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_sys_reg>;
 	};
 
 	clocks {
@@ -78,27 +108,85 @@
 		#size-cells = <0>;
 
 		/* audio external oscillator */
-		tlv320aic3x_mclk: oscillator@0 {
+		audio_mclk_fixed: oscillator@0 {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency  = <24576000>;	/* 24.576MHz */
 		};
+
+		audio_mclk: audio_mclk_gate@0 {
+			compatible = "gpio-gate-clock";
+			#clock-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&audio_mclk_pins>;
+			clocks = <&audio_mclk_fixed>;
+			enable-gpios = <&gpio1 27 0>;
+		};
+	};
+
+	panel: lcd_panel {
+		compatible = "ti,tilcdc,panel";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pins>;
+
+		panel-info {
+			ac-bias = <255>;
+			ac-bias-intrpt = <0>;
+			dma-burst-sz = <16>;
+			bpp = <16>;
+			fdd = <0x80>;
+			tft-alt-mode = <0>;
+			mono-8bit-mode = <0>;
+			sync-edge = <0>;
+			sync-ctrl = <1>;
+			raster-order = <0>;
+			fifo-th = <0>;
+		};
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: 960x128 {
+				clock-frequency = <18000000>;
+				hactive = <960>;
+				vactive = <272>;
+
+				hback-porch = <40>;
+				hfront-porch = <16>;
+				hsync-len = <24>;
+				hsync-active = <0>;
+
+				vback-porch = <3>;
+				vfront-porch = <8>;
+				vsync-len = <4>;
+				vsync-active = <0>;
+			};
+		};
 	};
 
 	sound {
-		compatible = "ti,da830-evm-audio";
-		ti,model = "AM335x-SL50";
-		ti,audio-codec = <&audio_codec>;
-		ti,mcasp-controller = <&mcasp0>;
+		compatible = "audio-graph-card";
+		label = "sound-card";
+		pinctrl-names = "default";
+		pinctrl-0 = <&audio_pa_pins>;
+
+		widgets = "Headphone", "Headphone Jack",
+			  "Speaker", "Speaker External",
+			  "Line", "Line In",
+			  "Microphone", "Microphone Jack";
 
-		clocks = <&tlv320aic3x_mclk>;
-		clock-names = "mclk";
+		routing = "Headphone Jack",	"HPLOUT",
+			  "Headphone Jack",	"HPROUT",
+			  "Amplifier",		"MONO_LOUT",
+			  "Speaker External",	"Amplifier",
+			  "LINE1R",		"Line In",
+			  "LINE1L",		"Line In",
+			  "MIC3L",		"Microphone Jack",
+			  "MIC3R",		"Microphone Jack",
+			  "Microphone Jack",	"Mic Bias";
 
-		ti,audio-routing =
-			"Headphone Jack",	"HPLOUT",
-			"Headphone Jack",	"HPROUT",
-			"LINE1R",               "Line In",
-			"LINE1L",		"Line In";
+		dais = <&cpu_port>;
+
+		pa-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
 	};
 
 	emmc_pwrseq: pwrseq@0 {
@@ -108,6 +196,14 @@
 		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
 	};
 
+	vdd_sys_reg: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_sys_reg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
 	vmmcsd_fixed: fixedregulator0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmcsd_fixed";
@@ -120,6 +216,65 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&lwb_pins>;
 
+	audio_pins: pinmux_audio_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_ahcklx.mcasp0_ahclkx */
+			AM33XX_IOPAD(0x994, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_fsx.mcasp0_fsx */
+			AM33XX_IOPAD(0x990, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_aclkx.mcasp0_aclkx */
+			AM33XX_IOPAD(0x998, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_axr0.mcasp0_axr0 */
+			AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mcasp0_ahclkr.mcasp0_axr2 */
+		>;
+	};
+
+	audio_pa_pins: pinmux_audio_pa_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9a0, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* SoundPA_en - mcasp0_aclkr.gpio3_18 */
+		>;
+	};
+
+	audio_mclk_pins: pinmux_audio_mclk_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a11.gpio1_27 */
+		>;
+	};
+
+	backlight0_pins: pinmux_backlight0_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE7)	/* gpmc_wen.gpio2_4 */
+		>;
+	};
+
+	backlight1_pins: pinmux_backlight1_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE7)     /* gpmc_ad10.gpio0_26 */
+		>;
+	};
+
+	lcd_pins: pinmux_lcd_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0)	/* lcd_data0.lcd_data0 */
+			AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0)	/* lcd_data1.lcd_data1 */
+			AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0)	/* lcd_data2.lcd_data2 */
+			AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0)	/* lcd_data3.lcd_data3 */
+			AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0)	/* lcd_data4.lcd_data4 */
+			AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0)	/* lcd_data5.lcd_data5 */
+			AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0)	/* lcd_data6.lcd_data6 */
+			AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0)	/* lcd_data7.lcd_data7 */
+			AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0)	/* lcd_data8.lcd_data8 */
+			AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0)	/* lcd_data9.lcd_data9 */
+			AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0)	/* lcd_data10.lcd_data10 */
+			AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0)	/* lcd_data11.lcd_data11 */
+			AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0)	/* lcd_data12.lcd_data12 */
+			AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0)	/* lcd_data13.lcd_data13 */
+			AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0)	/* lcd_data14.lcd_data14 */
+			AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0)	/* lcd_data15.lcd_data15 */
+			AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_vsync.lcd_vsync */
+			AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_hsync.lcd_hsync */
+			AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_pclk.lcd_pclk */
+			AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_ac_bias_en.lcd_ac_bias_en */
+		>;
+	};
+
 	led_pins: pinmux_led_pins {
 		pinctrl-single,pins = <
 			AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
@@ -207,6 +362,8 @@
 			/* MDIO */
 			AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
 			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+			/* Ethernet */
+			AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE7)	/* Ethernet_nRST - gpmc_ad14.gpio1_14 */
 		>;
 	};
 
@@ -245,20 +402,16 @@
 		>;
 	};
 
-	audio_pins: pinmux_audio_pins {
+	ehrpwm1_pins: pinmux_ehrpwm1a_pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_ahcklx.mcasp0_ahclkx */
-			AM33XX_IOPAD(0x994, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_fsx.mcasp0_fsx */
-			AM33XX_IOPAD(0x990, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_aclkx.mcasp0_aclkx */
-			AM33XX_IOPAD(0x998, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_axr0.mcasp0_axr0 */
-			AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mcasp0_ahclkr.mcasp0_axr2 */
+			AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE6)	/* gpmc_a2.ehrpwm1a */
+			AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE6)	/* gpmc_a3.ehrpwm1b */
 		>;
 	};
 
-	ehrpwm1_pins: pinmux_ehrpwm1a_pins {
+	rtc0_irq_pins: pinmux_rtc0_irq_pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE6)	/* gpmc_a2.ehrpwm1a */
-			AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE6)	/* gpmc_a3.ehrpwm1b */
+			AM33XX_IOPAD(0x824, PIN_INPUT_PULLUP | MUX_MODE7)     /* gpmc_ad9.gpio0_23 */
 		>;
 	};
 
@@ -274,15 +427,18 @@
 
 	lwb_pins: pinmux_lwb_pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x9a4, PIN_OUTPUT | MUX_MODE7)	/* SoundPA_en - mcasp0_fsr.gpio3_19 */
-			AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE7)	/* nKbdOnC - gpmc_ad10.gpio0_26 */
 			AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE7)	/* nKbdInt - gpmc_ad12.gpio1_12 */
 			AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE7)	/* nKbdReset - gpmc_ad13.gpio1_13 */
-			AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE7)	/* nDispReset - gpmc_ad14.gpio1_14 */
 			AM33XX_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7)	/* USB1_enPower - gpmc_a1.gpio1_17 */
 			/* PDI Bus - Battery system */
 			AM33XX_IOPAD(0x840, PIN_INPUT_PULLUP | MUX_MODE7)	/* nBattReset  gpmc_a0.gpio1_16 */
 			AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE7)	/* BattPDIData gpmc_ad15.gpio1_15 */
+			/* FPGA */
+			AM33XX_IOPAD(0x820, PIN_INPUT_PULLUP | MUX_MODE7)	/* FPGA_DONE - gpmc_ad8.gpio0_22 */
+			AM33XX_IOPAD(0x840, PIN_INPUT_PULLUP | MUX_MODE7)	/* FPGA_NRST - gpmc_a0.gpio1_16 */
+			AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* FPGA_RUN - gpmc_a1.gpio1_17 */
+			AM33XX_IOPAD(0x864, PIN_INPUT_PULLUP | MUX_MODE7)	/* ENFPGA - gpmc_a9.gpio1_25 */
+			AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* FPGA_PROGRAM - gpmc_a10.gpio1_26 */
 		>;
 	};
 };
@@ -298,9 +454,14 @@
 		reg = <0x24>;
 	};
 
-	bq32000: rtc@68 {
-		compatible = "ti,bq32000";
-		trickle-resistor-ohms = <1120>;
+	rtc0: rtc@68 {
+		compatible = "dallas,ds1339";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc0_irq_pins>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <23 IRQ_TYPE_EDGE_FALLING>; /* gpio 23 */
+		wakeup-source;
+		trickle-resistor-ohms = <2000>;
 		reg = <0x68>;
 	};
 
@@ -326,12 +487,21 @@
 	audio_codec: tlv320aic3106@1b {
 		status = "okay";
 		compatible = "ti,tlv320aic3106";
+		#sound-dai-cells = <0>;
 		reg = <0x1b>;
+		ai3x-micbias-vg = <2>;  /* 2.5V */
 
 		AVDD-supply = <&ldo4_reg>;
 		IOVDD-supply = <&ldo4_reg>;
 		DRVDD-supply = <&ldo4_reg>;
 		DVDD-supply = <&ldo3_reg>;
+
+		codec_port: port {
+			codec_endpoint: endpoint {
+				remote-endpoint = <&cpu_endpoint>;
+				clocks = <&audio_mclk>;
+			};
+		};
 	};
 
 	/* Ambient Light Sensor */
@@ -363,7 +533,7 @@
 
 &usb0 {
 	status = "okay";
-	dr_mode = "peripheral";
+	dr_mode = "otg";
 };
 
 &usb1 {
@@ -397,17 +567,27 @@
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&audio_pins>;
-
+	#sound-dai-cells = <0>;
 	op-mode = <0>;  /* MCASP_ISS_MODE */
 	tdm-slots = <2>;
-	serial-dir = <
-		2 0 1 0
-		0 0 0 0
-		0 0 0 0
-		0 0 0 0
+	/* 4 serializers */
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+		0 0 1 2
 	>;
-	tx-num-evt = <1>;
-	rx-num-evt = <1>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+
+	cpu_port: port {
+		cpu_endpoint: endpoint {
+			remote-endpoint = <&codec_endpoint>;
+
+			dai-format = "dsp_b";
+			bitclock-master = <&codec_port>;
+			frame-master = <&codec_port>;
+			bitclock-inversion;
+			clocks = <&audio_mclk>;
+		};
+	};
 };
 
 &uart0 {
@@ -507,13 +687,8 @@
 };
 
 &cpsw_emac0 {
-	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "mii";
-};
-
-&cpsw_emac1 {
-	phy_id = <&davinci_mdio>, <1>;
 	phy-mode = "mii";
+	phy-handle = <&ethphy0>;
 };
 
 &mac {
@@ -528,6 +703,12 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
+	reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <100>;   /* PHY datasheet states 100us min */
+
+	ethphy0: ethernet-phy@0 {
+		reg = <0>;
+	};
 };
 
 &sham {
@@ -547,3 +728,15 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&ehrpwm1_pins>;
 };
+
+&lcdc {
+	status = "okay";
+};
+
+&tscadc {
+	status = "okay";
+};
+
+&am335x_adc {
+	ti,adc-channels = <0 1 2 3 4 5 6 7>;
+};

arch/arm/boot/dts/am33xx.dtsi

@@ -29,8 +29,8 @@
 		serial3 = &uart3;
 		serial4 = &uart4;
 		serial5 = &uart5;
-		d_can0 = &dcan0;
-		d_can1 = &dcan1;
+		d-can0 = &dcan0;
+		d-can1 = &dcan1;
 		usb0 = &usb0;
 		usb1 = &usb1;
 		phy0 = &usb0_phy;

arch/arm/boot/dts/am3517-evm.dts

@@ -127,6 +127,7 @@
 		status = "okay";
 		pinctrl-names = "default";
 		enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;	/* gpio176, lcd INI */
+		vcc-supply = <&vdd_io_reg>;
 
 		port {
 			lcd_in: endpoint {
@@ -154,6 +155,7 @@
 	bl: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
+		power-supply = <&vdd_io_reg>;
 		pinctrl-0 = <&backlight_pins>;
 		pwms = <&pwm11 0 5000000 0>;
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
@@ -168,6 +170,13 @@
 		ti,timers = <&timer11>;
 		#pwm-cells = <3>;
 	};
+
+	/* HS USB Host PHY on PORT 1 */
+	hsusb1_phy: hsusb1_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; /* gpio_57 */
+		#phy-cells = <0>;
+	};
 };
 
 &davinci_emac {
@@ -203,6 +212,7 @@
 		reg = <0x21>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		vcc-supply = <&vdd_io_reg>;
 	};
 };
 
@@ -220,15 +230,21 @@
 	cd-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio_127 */
 };
 
-&mmc2 {
+&mmc3 {
       status = "disabled";
 };
 
-&mmc3 {
-      status = "disabled";
+&usbhshost {
+	port1-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy>;
 };
 
 &omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb1_rst_pins>;
 
 	leds_pins: pinmux_leds_pins {
 		pinctrl-single,pins = <
@@ -287,4 +303,32 @@
 			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)       /* dss_data15.dss_data15 */
 		>;
 	};
+
+	hsusb1_rst_pins: pinmux_hsusb1_rst_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4)	/* gpmc_ncs6.gpio_57 */
+		>;
+	};
+};
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb1_pins>;
+
+	hsusb1_pins: pinmux_hsusb1_pins {
+		pinctrl-single,pins = <
+			OMAP3430_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3)	/* etk_clk.hsusb1_stp */
+			OMAP3430_CORE2_IOPAD(0x25da, PIN_OUTPUT | MUX_MODE3)	/* etk_ctl.hsusb1_clk */
+			OMAP3430_CORE2_IOPAD(0x25ec, PIN_INPUT | MUX_MODE3)	/* etk_d8.hsusb1_dir */
+			OMAP3430_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE3)	/* etk_d9.hsusb1_nxt */
+			OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE3)	/* etk_d0.hsusb1_data0 */
+			OMAP3430_CORE2_IOPAD(0x25de, PIN_INPUT | MUX_MODE3)	/* etk_d1.hsusb1_data1 */
+			OMAP3430_CORE2_IOPAD(0x25e0, PIN_INPUT | MUX_MODE3)	/* etk_d2.hsusb1_data2 */
+			OMAP3430_CORE2_IOPAD(0x25ea, PIN_INPUT | MUX_MODE3)	/* etk_d7.hsusb1_data3 */
+			OMAP3430_CORE2_IOPAD(0x25e4, PIN_INPUT | MUX_MODE3)	/* etk_d4.hsusb1_data4 */
+			OMAP3430_CORE2_IOPAD(0x25e6, PIN_INPUT | MUX_MODE3)	/* etk_d5.hsusb1_data5 */
+			OMAP3430_CORE2_IOPAD(0x25e8, PIN_INPUT | MUX_MODE3)	/* etk_d6.hsusb1_data6 */
+			OMAP3430_CORE2_IOPAD(0x25e2, PIN_INPUT | MUX_MODE3)	/* etk_d3.hsusb1_data7 */
+		>;
+	};
 };

arch/arm/boot/dts/am3517-som.dtsi

@@ -14,6 +14,32 @@
 			cpu0-supply = <&vdd_core_reg>;
 		};
 	};
+
+	wl12xx_buffer: wl12xx_buf {
+		compatible = "regulator-fixed";
+		regulator-name = "wl1271_buf";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_buffer_pins>;
+		gpio = <&gpio5 1 GPIO_ACTIVE_LOW>; /* gpio 129 */
+		regulator-always-on;
+		vin-supply = <&vdd_1v8_reg>;
+	};
+
+	wl12xx_vmmc2: wl12xx_vmmc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_wkup_pins>;
+		gpio = <&gpio1 3 GPIO_ACTIVE_HIGH >; /* gpio 3 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		regulator-always-on;
+		vin-supply = <&wl12xx_buffer>;
+	};
 };
 
 &gpmc {
@@ -64,7 +90,6 @@
 		regulators {
 			vdd_core_reg: VDCDC1 {
 				regulator-name = "vdd_core";
-				compatible = "regulator-fixed";
 				regulator-always-on;
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1200000>;
@@ -72,7 +97,6 @@
 
 			vdd_io_reg: VDCDC2 {
 				regulator-name = "vdd_io";
-				compatible = "regulator-fixed";
 				regulator-always-on;
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
@@ -80,7 +104,6 @@
 
 			vdd_1v8_reg: VDCDC3 {
 				regulator-name = "vdd_1v8";
-				compatible = "regulator-fixed";
 				regulator-always-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
@@ -88,7 +111,6 @@
 
 			vdd_usb18_reg: LDO1 {
 				regulator-name = "vdd_usb18";
-				compatible = "regulator-fixed";
 				regulator-always-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
@@ -96,7 +118,6 @@
 
 			vdd_usb33_reg: LDO2 {
 				regulator-name = "vdd_usb33";
-				compatible = "regulator-fixed";
 				regulator-always-on;
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
@@ -126,8 +147,63 @@
 	};
 };
 
+&mmc2 {
+	interrupts-extended = <&intc 86 /* &omap3_pmx_core 0x12c */>;
+
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&wl12xx_vmmc2>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1271";
+		reg = <2>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; /* gpio_170 */
+		ref-clock-frequency = <26000000>;
+		tcxo-clock-frequency = <26000000>;
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+
+	bluetooth {
+		compatible = "ti,wl1271-st";
+		enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; /* gpio 56 */
+		max-speed = <3000000>;
+	};
+};
+
 &omap3_pmx_core {
 
+	wl12xx_buffer_pins: pinmux_wl12xx_buffer_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4)  /* mmc1_dat7.gpio_129 */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc2_clk.mmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc2_cmd.mmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc2_dat0.mmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc2_dat1.mmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc2_dat2.mmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc2_dat3.mmc2_dat3 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* mmc2_dat4.mmc2_dir_dat0 */
+			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* mmc2_dat5.mmc2_dir_dat1 */
+			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* mmc2_dat6.mmc2_dir_cmd */
+			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* mmc2_dat7.mmc2_clkin */
+			OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE4)	/* hdq_sio.gpio_170 */
+		>;
+	};
+
 	rtc_pins: pinmux_rtc_pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20b6, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_ncs4.gpio_55 */
@@ -139,4 +215,23 @@
 			OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT | MUX_MODE4) /* gpmc_wait3.gpio_65 */
 		>;
 	};
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)		/* uart2_cts */
+			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* uart2_rts */
+			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx */
+			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)		/* uart2_rx */
+			OMAP3_CORE1_IOPAD(0x20b8, PIN_INPUT | MUX_MODE0)		/* gpio_56 */
+		>;
+	};
+};
+
+&omap3_pmx_wkup {
+
+	wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
+		>;
+	};
 };

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -790,7 +790,7 @@
 		compatible = "ti,wl1835";
 		reg = <2>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <23 IRQ_TYPE_EDGE_RISING>;
 	};
 };
 

arch/arm/boot/dts/am571x-idk.dts

@@ -66,10 +66,6 @@
 	};
 };
 
-&omap_dwc3_2 {
-	extcon = <&extcon_usb2>;
-};
-
 &extcon_usb2 {
 	id-gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
 	vbus-gpio = <&gpio7 22 GPIO_ACTIVE_HIGH>;

arch/arm/boot/dts/am572x-idk-common.dtsi

@@ -57,10 +57,6 @@
 	};
 };
 
-&omap_dwc3_2 {
-	extcon = <&extcon_usb2>;
-};
-
 &extcon_usb2 {
 	id-gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
 	vbus-gpio = <&gpio3 26 GPIO_ACTIVE_HIGH>;

arch/arm/boot/dts/am57xx-idk-common.dtsi

@@ -395,8 +395,13 @@
 	dr_mode = "host";
 };
 
+&omap_dwc3_2 {
+	extcon = <&extcon_usb2>;
+};
+
 &usb2 {
-	dr_mode = "peripheral";
+	extcon = <&extcon_usb2>;
+	dr_mode = "otg";
 };
 
 &mmc1 {

arch/arm/boot/dts/armada-388-clearfog-base.dts

@@ -3,11 +3,6 @@
  * Device Tree file for SolidRun Clearfog Base revision A1 rev 2.0 (88F6828)
  *
  *  Copyright (C) 2015 Russell King
- *
- * This board is in development; the contents of this file work with
- * the A1 rev 2.0 of the board, which does not represent final
- * production board.  Things will change, don't expect this file to
- * remain compatible info the future.
  */
 
 /dts-v1/;

arch/arm/boot/dts/armada-388-clearfog-pro.dts

@@ -3,11 +3,6 @@
  * Device Tree file for SolidRun Clearfog Pro revision A1 rev 2.0 (88F6828)
  *
  *  Copyright (C) 2015 Russell King
- *
- * This board is in development; the contents of this file work with
- * the A1 rev 2.0 of the board, which does not represent final
- * production board.  Things will change, don't expect this file to
- * remain compatible info the future.
  */
 #include "armada-388-clearfog.dts"
 

arch/arm/boot/dts/armada-388-clearfog.dts

@@ -3,11 +3,6 @@
  * Device Tree file for SolidRun Clearfog Pro revision A1 rev 2.0 (88F6828)
  *
  *  Copyright (C) 2015 Russell King
- *
- * This board is in development; the contents of this file work with
- * the A1 rev 2.0 of the board, which does not represent final
- * production board.  Things will change, don't expect this file to
- * remain compatible info the future.
  */
 
 /dts-v1/;
@@ -235,7 +230,7 @@
 &spi1 {
 	/*
 	 * Add SPI CS pins for clearfog:
-	 * CS0: W25Q32 (not populated on uSOM)
+	 * CS0: W25Q32
 	 * CS1:
 	 * CS2: mikrobus
 	 */

arch/arm/boot/dts/armada-388-clearfog.dtsi

@@ -3,11 +3,6 @@
  * Device Tree include file for SolidRun Clearfog 88F6828 based boards
  *
  *  Copyright (C) 2015 Russell King
- *
- * This board is in development; the contents of this file work with
- * the A1 rev 2.0 of the board, which does not represent final
- * production board.  Things will change, don't expect this file to
- * remain compatible info the future.
  */
 
 #include "armada-388.dtsi"
@@ -230,7 +225,7 @@
 &spi1 {
 	/*
 	 * Add SPI CS pins for clearfog:
-	 * CS0: W25Q32 (not populated on uSOM)
+	 * CS0: W25Q32
 	 * CS1: PIC microcontroller (Pro models)
 	 * CS2: mikrobus
 	 */

arch/arm/boot/dts/armada-388-helios4.dts

@@ -0,0 +1,313 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Helios4
+ * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828)
+ *
+ *  Copyright (C) 2017 Aditya Prayoga <aditya@kobol.io>
+ *
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include "armada-38x-solidrun-microsom.dtsi"
+
+/ {
+	model = "Helios4";
+	compatible = "kobol,helios4", "marvell,armada388",
+		"marvell,armada385", "marvell,armada380";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000>; /* 2 GB */
+	};
+
+	aliases {
+		/* So that mvebu u-boot can update the MAC addresses */
+		ethernet1 = &eth0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_12v: regulator-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "power_brick_12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_12v>;
+	};
+
+	reg_5p0v_hdd: regulator-5v-hdd {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_HDD";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_12v>;
+	};
+
+	reg_5p0v_usb: regulator-5v-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "USB-PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		enable-active-high;
+		gpio = <&expander0 6 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&reg_12v>;
+	};
+
+	system-leds {
+		compatible = "gpio-leds";
+		status-led {
+			label = "helios4:green:status";
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+
+		fault-led {
+			label = "helios4:red:fault";
+			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+	};
+
+	io-leds {
+		compatible = "gpio-leds";
+		sata1-led {
+			label = "helios4:green:ata1";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata1";
+			default-state = "off";
+		};
+		sata2-led {
+			label = "helios4:green:ata2";
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata2";
+			default-state = "off";
+		};
+		sata3-led {
+			label = "helios4:green:ata3";
+			gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata3";
+			default-state = "off";
+		};
+		sata4-led {
+			label = "helios4:green:ata4";
+			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata4";
+			default-state = "off";
+		};
+		usb-led {
+			label = "helios4:green:usb";
+			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usb-host";
+			default-state = "off";
+		};
+	};
+
+	fan1: j10-pwm {
+		compatible = "pwm-fan";
+		pwms = <&gpio1 9 40000>;	/* Target freq:25 kHz */
+	};
+
+	fan2: j17-pwm {
+		compatible = "pwm-fan";
+		pwms = <&gpio1 23 40000>;	/* Target freq:25 kHz */
+	};
+
+	usb2_phy: usb2-phy {
+		compatible = "usb-nop-xceiv";
+		vbus-regulator = <&reg_5p0v_usb>;
+	};
+
+	usb3_phy: usb3-phy {
+		compatible = "usb-nop-xceiv";
+	};
+
+	soc {
+		internal-regs {
+			i2c@11000 {
+				clock-frequency = <400000>;
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+
+				/*
+				 * PCA9655 GPIO expander, up to 1MHz clock.
+				 *  0-Board Revision bit 0 #
+				 *  1-Board Revision bit 1 #
+				 *  5-USB3 overcurrent
+				 *  6-USB3 power
+				 */
+				expander0: gpio-expander@20 {
+					/*
+					 * This is how it should be:
+					 * compatible = "onnn,pca9655",
+					 *	 "nxp,pca9555";
+					 * but you can't do this because of
+					 * the way I2C works.
+					 */
+					compatible = "nxp,pca9555";
+					gpio-controller;
+					#gpio-cells = <2>;
+					reg = <0x20>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pca0_pins>;
+					interrupt-parent = <&gpio0>;
+					interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+
+					board_rev_bit_0 {
+						gpio-hog;
+						gpios = <0 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "board-rev-0";
+					};
+					board_rev_bit_1 {
+						gpio-hog;
+						gpios = <1 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "board-rev-1";
+					};
+					usb3_ilimit {
+						gpio-hog;
+						gpios = <5 GPIO_ACTIVE_HIGH>;
+						input;
+						line-name = "usb-overcurrent-status";
+					};
+				};
+
+				temp_sensor: temp@4c {
+					compatible = "ti,lm75";
+					reg = <0x4c>;
+					vcc-supply = <&reg_3p3v>;
+				};
+			};
+
+			i2c@11100 {
+				/*
+				 * External I2C Bus for user peripheral
+				 */
+				clock-frequency = <400000>;
+				pinctrl-0 = <&helios_i2c1_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			sata@a8000 {
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sata0: sata-port@0 {
+					reg = <0>;
+				};
+
+				sata1: sata-port@1 {
+					reg = <1>;
+				};
+			};
+
+			sata@e0000 {
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sata2: sata-port@0 {
+					reg = <0>;
+				};
+
+				sata3: sata-port@1 {
+					reg = <1>;
+				};
+			};
+
+			spi@10680 {
+				pinctrl-0 = <&spi1_pins
+					     &microsom_spi1_cs_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			sdhci@d8000 {
+				bus-width = <4>;
+				cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+				no-1-8-v;
+				pinctrl-0 = <&helios_sdhci_pins
+					     &helios_sdhci_cd_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				vmmc = <&reg_3p3v>;
+				wp-inverted;
+			};
+
+			usb@58000 {
+				usb-phy = <&usb2_phy>;
+				status = "okay";
+			};
+
+			usb3@f0000 {
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				status = "okay";
+			};
+
+			pinctrl@18000 {
+				pca0_pins: pca0-pins {
+					marvell,pins = "mpp23";
+					marvell,function = "gpio";
+				};
+				microsom_phy0_int_pins: microsom-phy0-int-pins {
+					marvell,pins = "mpp18";
+					marvell,function = "gpio";
+				};
+				helios_i2c1_pins: i2c1-pins {
+					marvell,pins = "mpp26", "mpp27";
+					marvell,function = "i2c1";
+				};
+				helios_sdhci_cd_pins: helios-sdhci-cd-pins {
+					marvell,pins = "mpp20";
+					marvell,function = "gpio";
+				};
+				helios_sdhci_pins: helios-sdhci-pins {
+					marvell,pins = "mpp21", "mpp28",
+						       "mpp37", "mpp38",
+						       "mpp39", "mpp40";
+					marvell,function = "sd0";
+				};
+				helios_led_pins: helios-led-pins {
+					marvell,pins = "mpp24", "mpp25",
+						       "mpp49", "mpp50",
+						       "mpp52", "mpp53",
+						       "mpp54";
+					marvell,function = "gpio";
+				};
+				helios_fan_pins: helios-fan-pins {
+					marvell,pins = "mpp41", "mpp43",
+						       "mpp48", "mpp55";
+					marvell,function = "gpio";
+				};
+				microsom_spi1_cs_pins: spi1-cs-pins {
+					marvell,pins = "mpp59";
+					marvell,function = "spi1";
+				};
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi

@@ -3,11 +3,6 @@
  * Device Tree file for SolidRun Armada 38x Microsom
  *
  *  Copyright (C) 2015 Russell King
- *
- * This board is in development; the contents of this file work with
- * the A1 rev 2.0 of the board, which does not represent final
- * production board.  Things will change, don't expect this file to
- * remain compatible info the future.
  */
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -99,7 +94,6 @@
 		compatible = "w25q32", "jedec,spi-nor";
 		reg = <0>; /* Chip select 0 */
 		spi-max-frequency = <3000000>;
-		status = "disabled";
 	};
 };
 

arch/arm/boot/dts/aspeed-ast2500-evb.dts

@@ -80,20 +80,20 @@
 	};
 };
 
-&ehci0 {
+/*
+ * Enable port A as device (via the virtual hub) and port B as
+ * host by default on the eval board. This can be easily changed
+ * by replacing the override below with &ehci0 { ... } to enable
+ * host on both ports.
+ */
+&vhub {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usb2ah_default>;
 };
 
 &ehci1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usb2bh_default>;
 };
 
 &uhci {
 	status = "okay";
-
-	/* No pinctrl, this follows the above EHCI settings */
 };

arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts

@@ -21,9 +21,9 @@
 		#size-cells = <1>;
 		ranges;
 
-		vga_memory: framebuffer@bf000000 {
+		vga_memory: framebuffer@9f000000 {
 			no-map;
-			reg = <0xbf000000 0x01000000>; /* 16M */
+			reg = <0x9f000000 0x01000000>; /* 16M */
 		};
 
 		flash_memory: region@98000000 {

arch/arm/boot/dts/aspeed-g4.dtsi

@@ -92,6 +92,12 @@
 			reg = <0x1e6c0080 0x80>;
 		};
 
+		cvic: copro-interrupt-controller@1e6c2000 {
+			compatible = "aspeed,ast2400-cvic", "aspeed-cvic";
+			valid-sources = <0x7fffffff>;
+			reg = <0x1e6c2000 0x80>;
+		};
+
 		mac0: ethernet@1e660000 {
 			compatible = "aspeed,ast2400-mac", "faraday,ftgmac100";
 			reg = <0x1e660000 0x180>;
@@ -113,6 +119,8 @@
 			reg = <0x1e6a1000 0x100>;
 			interrupts = <5>;
 			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2h_default>;
 			status = "disabled";
 		};
 
@@ -123,6 +131,20 @@
 			#ports = <3>;
 			clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>;
 			status = "disabled";
+			/*
+			 * No default pinmux, it will follow EHCI, use an explicit pinmux
+			 * override if you don't enable EHCI
+			 */
+		};
+
+		vhub: usb-vhub@1e6a0000 {
+			compatible = "aspeed,ast2400-usb-vhub";
+			reg = <0x1e6a0000 0x300>;
+			interrupts = <5>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2d_default>;
+			status = "disabled";
 		};
 
 		apb {
@@ -161,7 +183,7 @@
 				status = "disabled";
 			};
 
-			sram@1e720000 {
+			sram: sram@1e720000 {
 				compatible = "mmio-sram";
 				reg = <0x1e720000 0x8000>;	// 32K
 			};
@@ -224,7 +246,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0x1e786000 0x1000>;
-				clocks = <&syscon ASPEED_CLK_APB>;
+				clocks = <&syscon ASPEED_CLK_24M>;
 				resets = <&syscon ASPEED_RESET_PWM>;
 				status = "disabled";
 			};

arch/arm/boot/dts/aspeed-g5.dtsi

@@ -127,6 +127,13 @@
 			reg = <0x1e6c0080 0x80>;
 		};
 
+		cvic: copro-interrupt-controller@1e6c2000 {
+			compatible = "aspeed,ast2500-cvic", "aspeed-cvic";
+			valid-sources = <0xffffffff>;
+			copro-sw-interrupts = <1>;
+			reg = <0x1e6c2000 0x80>;
+		};
+
 		mac0: ethernet@1e660000 {
 			compatible = "aspeed,ast2500-mac", "faraday,ftgmac100";
 			reg = <0x1e660000 0x180>;
@@ -148,6 +155,8 @@
 			reg = <0x1e6a1000 0x100>;
 			interrupts = <5>;
 			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2ah_default>;
 			status = "disabled";
 		};
 
@@ -156,6 +165,8 @@
 			reg = <0x1e6a3000 0x100>;
 			interrupts = <13>;
 			clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2bh_default>;
 			status = "disabled";
 		};
 
@@ -166,6 +177,20 @@
 			#ports = <2>;
 			clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>;
 			status = "disabled";
+			/*
+			 * No default pinmux, it will follow EHCI, use an explicit pinmux
+			 * override if you don't enable EHCI
+			 */
+		};
+
+		vhub: usb-vhub@1e6a0000 {
+			compatible = "aspeed,ast2500-usb-vhub";
+			reg = <0x1e6a0000 0x300>;
+			interrupts = <5>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2ad_default>;
+			status = "disabled";
 		};
 
 		apb {
@@ -211,7 +236,7 @@
 				status = "disabled";
 			};
 
-			sram@1e720000 {
+			sram: sram@1e720000 {
 				compatible = "mmio-sram";
 				reg = <0x1e720000 0x9000>;	// 36K
 			};
@@ -281,7 +306,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0x1e786000 0x1000>;
-				clocks = <&syscon ASPEED_CLK_APB>;
+				clocks = <&syscon ASPEED_CLK_24M>;
 				resets = <&syscon ASPEED_RESET_PWM>;
 				status = "disabled";
 			};
@@ -1417,6 +1442,11 @@
 		groups = "USB2AH";
 	};
 
+	pinctrl_usb2ad_default: usb2ad_default {
+		function = "USB2AD";
+		groups = "USB2AD";
+	};
+
 	pinctrl_usb11bhid_default: usb11bhid_default {
 		function = "USB11BHID";
 		groups = "USB11BHID";

arch/arm/boot/dts/at91-dvk_som60.dts

@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-dvk_som60.dts - Device Tree file for the DVK SOM60 board
+ *
+ *  Copyright (C) 2018 Laird,
+ *		  2018 Ben Whitten <ben.whitten@lairdtech.com>
+ *
+ */
+/dts-v1/;
+#include "at91-som60.dtsi"
+#include "at91-dvk_su60_somc.dtsi"
+#include "at91-dvk_su60_somc_lcm.dtsi"
+
+/ {
+	model = "Laird DVK SOM60";
+	compatible = "laird,dvk-som60", "laird,som60", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		stdout-path = &dbgu;
+		tick-timer = &pit;
+	};
+};
+
+&mmc0 {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+};
+
+&ssc0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&usart1 {
+	status = "okay";
+};
+
+&usart2 {
+	status = "okay";
+};
+
+&usart3 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&pit {
+	status = "okay";
+};
+
+&adc0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&macb0 {
+	status = "okay";
+};
+
+&macb1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+

arch/arm/boot/dts/at91-dvk_su60_somc.dtsi

@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-dvk_su60_somc.dtsi - Device Tree file for the DVK SOM60 base board
+ *
+ *  Copyright (C) 2018 Laird,
+ *		  2018 Ben Whitten <ben.whitten@lairdtech.com>
+ *
+ */
+
+/ {
+	sound {
+		compatible = "atmel,asoc-wm8904";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pck2_as_audio_mck>;
+
+		atmel,model = "wm8904 @ DVK-SOM60";
+		atmel,audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Mic", "MICBIAS",
+			"IN1L", "Mic";
+
+		atmel,ssc-controller = <&ssc0>;
+		atmel,audio-codec = <&wm8904>;
+
+		status = "okay";
+	};
+};
+
+&mmc0 {
+	status = "okay";
+
+	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+	slot@0 {
+		bus-width = <4>;
+		cd-gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
+		cd-inverted;
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	/* spi0.0: 4M Flash Macronix MX25R4035FM1IL0 */
+	spi-flash@0 {
+		compatible = "mxicy,mx25u4035", "jedec,spi-nor";
+		spi-max-frequency = <33000000>;
+		reg = <0>;
+	};
+};
+
+&ssc0 {
+	atmel,clk-from-rk-pin;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	wm8904: wm8904@1a {
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+		clocks = <&pck2>;
+		clock-names = "mclk";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	eeprom@87 {
+		compatible = "giantec,gt24c32a", "atmel,24c32";
+		reg = <87>;
+		pagesize = <32>;
+	};
+};
+
+&usart1 {
+	status = "okay";
+};
+
+&usart2 {
+	status = "okay";
+};
+
+&usart3 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&pit {
+	status = "okay";
+};
+
+&adc0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&macb0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ethernet-phy@7 {
+		reg = <7>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_geth_int>;
+		interrupt-parent = <&pioB>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		txen-skew-ps = <800>;
+		txc-skew-ps = <3000>;
+		rxdv-skew-ps = <400>;
+		rxc-skew-ps = <3000>;
+		rxd0-skew-ps = <400>;
+		rxd1-skew-ps = <400>;
+		rxd2-skew-ps = <400>;
+		rxd3-skew-ps = <400>;
+	};
+};
+
+&macb1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ethernet-phy@1 {
+		reg = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_eth_int>;
+		interrupt-parent = <&pioC>;
+		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+

arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi

@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-dvk_su60_somc_lcm.dtsi - Device Tree file for the DVK SOM60 LCD board
+ *
+ *  Copyright (C) 2018 Laird,
+ *		  2018 Ben Whitten <ben.whitten@lairdtech.com>
+ *
+ */
+
+/ {
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&hlcdc_pwm 0 50000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+
+	panel: panel {
+		compatible = "winstar,wf70gtiagdng0", "innolux,at070tn92", "simple-panel";
+		backlight = <&backlight>;
+		power-supply = <&vcc_lcd_reg>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			panel_input: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&hlcdc_panel_output>;
+			};
+		};
+	};
+
+	vcc_lcd_reg: fixedregulator_lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC LCM";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		status = "okay";
+	};
+};
+
+&pinctrl {
+	board {
+		pinctrl_lcd_ctp_int: lcd_ctp_int {
+			 atmel,pins =
+				 <AT91_PIOC 28 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	ft5426@56 {
+		compatible = "focaltech,ft5426", "edt,edt-ft5406";
+		reg = <56>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd_ctp_int>;
+
+		interrupt-parent = <&pioC>;
+		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+	};
+};
+
+&hlcdc {
+	status = "okay";
+
+	hlcdc-display-controller {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+
+		port@0 {
+			hlcdc_panel_output: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&panel_input>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/at91-gatwick.dts

@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-gatwick.dts - Device Tree file for the Gatwick board
+ *
+ *  Copyright (C) 2018 Laird
+ *
+ */
+/dts-v1/;
+#include "at91-wb50n.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Laird Workgroup Bridge 50N - Project Gatwick";
+	compatible = "laird,gatwick", "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio>;
+
+		reset-button {
+			label = "Reset Button";
+			linux,code = <KEY_SETUP>;
+			gpios = <&pioE 31 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		ethernet {
+			label = "gatwick:yellow:ethernet";
+			gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		wifi {
+			label = "gatwick:green:wifi";
+			gpios = <&pioA 28 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		ble {
+			label = "gatwick:blue:ble";
+			gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		lora {
+			label = "gatwick:orange:lora";
+			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		blank {
+			label = "gatwick:green:blank";
+			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		user {
+			label = "gatwick:yellow:user";
+			gpios = <&pioA 12 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&pinctrl {
+	board {
+		pinctrl_key_gpio: key_gpio_0 {
+		  atmel,pins =
+			  <AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PE31 GPIO with pullup deglitch */
+	  };
+	};
+};
+
+&mmc0 {
+	status = "okay";
+};
+
+&macb1 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+/* FTDI USART */
+&usart0 {
+	status = "okay";
+};
+
+/* GPS USART */
+&usart1 {
+	pinctrl-0 = <&pinctrl_usart1>;
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+
+	spidev@0 {
+		compatible = "semtech,sx1301";
+		reg = <0>;
+		spi-max-frequency = <8000000>;
+	};
+};
+
+&usb1 {
+	status = "okay";
+	/delete-property/atmel,oc-gpio;
+};
+
+&usb2 {
+	status = "okay";
+};

arch/arm/boot/dts/at91-som60.dtsi

@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-som60.dtsi - Device Tree file for the SOM60 module
+ *
+ *  Copyright (C) 2018 Laird,
+ *		  2018 Ben Whitten <ben.whitten@lairdtech.com>
+ *
+ */
+#include "sama5d36.dtsi"
+
+/ {
+	model = "Laird SOM60";
+	compatible = "laird,som60", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		stdout-path = &dbgu;
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+};
+
+&pinctrl {
+	board {
+		pinctrl_mmc0_cd: mmc0_cd {
+			atmel,pins =
+				<AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_mmc0_en: mmc0_en {
+			atmel,pins =
+				<AT91_PIOE 30 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_nand0_wp: nand0_wp {
+			atmel,pins =
+				<AT91_PIOE 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_usb_vbus: usb_vbus {
+			atmel,pins =
+				<AT91_PIOE 20 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+				/* Conflicts with USART2_SCK */
+		};
+
+		pinctrl_usart2_sck: usart2_sck {
+			atmel,pins =
+				<AT91_PIOE 20 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+				/* Conflicts with USB_VBUS */
+		};
+
+		pinctrl_usb_oc: usb_oc {
+			atmel,pins =
+				<AT91_PIOE 15 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+				/* Conflicts with USART3_SCK */
+		};
+
+		pinctrl_usart3_sck: usart3_sck {
+			atmel,pins =
+				<AT91_PIOE 15 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+				/* Conflicts with USB_OC */
+		};
+
+		pinctrl_usba_vbus: usba_vbus {
+		   atmel,pins =
+				<AT91_PIOC 14 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_geth_int: geth_int {
+			atmel,pins =
+				<AT91_PIOB 25 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+				/* Conflicts with USART1_SCK */
+		};
+
+		pinctrl_usart1_sck: usart1_sck {
+			atmel,pins =
+				<AT91_PIOB 25 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+				/* Conflicts with GETH_INT */
+		};
+
+		pinctrl_eth_int: eth_int {
+			atmel,pins =
+				<AT91_PIOC 10 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_pck2_as_audio_mck: pck2_as_audio_mck {
+			atmel,pins =
+				<AT91_PIOC 15 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+	};
+};
+
+&mmc0 {
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+	};
+};
+
+&mmc1 {
+	status = "okay";
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+	};
+};
+
+&spi0 {
+	cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+};
+
+&usart0 {
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>;
+};
+
+&usart1 {
+	pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+};
+
+&usart2 {
+	pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rts_cts>;
+};
+
+&usart3 {
+	pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>;
+};
+
+&adc0 {
+	pinctrl-0 = <
+		&pinctrl_adc0_adtrg
+		&pinctrl_adc0_ad0
+		&pinctrl_adc0_ad1
+		&pinctrl_adc0_ad2
+		&pinctrl_adc0_ad3
+		&pinctrl_adc0_ad4
+		&pinctrl_adc0_ad5
+		>;
+};
+
+&macb0 {
+	phy-mode = "rgmii";
+};
+
+&macb1 {
+	phy-mode = "rmii";
+};
+
+&ebi {
+	pinctrl-0 = <&pinctrl_ebi_nand_addr>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand: nand@3 {
+		reg = <0x3 0x0 0x2>;
+		atmel,rb = <0>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-on-flash-bbt;
+		label = "atmel_nand";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ubootspl@0 {
+				label = "u-boot-spl";
+				reg = <0x0 0x20000>;
+			};
+
+			uboot@20000 {
+				label = "u-boot";
+				reg = <0x20000 0x80000>;
+			};
+
+			ubootenv@a0000 {
+				label = "u-boot-env";
+				reg = <0xa0000 0x20000>;
+			};
+
+			ubootenv@c0000 {
+				label = "u-boot-env";
+				reg = <0xc0000 0x20000>;
+			};
+
+			ubi@e0000 {
+				label = "ubi";
+				reg = <0xe0000 0xfe00000>;
+			};
+		};
+	};
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	atmel,vbus-gpio = <&pioC 14 GPIO_ACTIVE_HIGH>;
+};
+
+&usb1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_vbus &pinctrl_usb_oc>;
+	num-ports = <3>;
+	atmel,vbus-gpio = <0
+		&pioE 20 GPIO_ACTIVE_HIGH
+		0>;
+	atmel,oc-gpio = <0
+		&pioE 15 GPIO_ACTIVE_LOW
+		0>;
+};

arch/arm/boot/dts/at91-wb45n.dts

@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-wb45n.dts - Device Tree file for WB45NBT board
+ *
+ *  Copyright (C) 2018 Laird
+ *
+ */
+/dts-v1/;
+#include "at91-wb45n.dtsi"
+
+/ {
+	model = "Laird Workgroup Bridge 45N - Atmel AT91SAM (dt)";
+	compatible = "laird,wb45n", "laird,wbxx", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		irqbtn@18 {
+			reg = <18>;
+			label = "IRQBTN";
+			linux,code = <99>;
+			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup = <1>;
+		};
+	};
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&mmc0 {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+};
+
+&macb0 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&usart0 {
+	status = "okay";
+};
+
+&usart3 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};

arch/arm/boot/dts/at91-wb45n.dtsi

@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-wb45n.dtsi - Device Tree file for WB45NBT board
+ *
+ *  Copyright (C) 2018 Laird
+ *
+ */
+
+#include "at91sam9g25.dtsi"
+
+/ {
+	model = "Laird Workgroup Bridge 45N - Atmel AT91SAM (dt)";
+	compatible = "laird,wb45n", "laird,wbxx", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs rw";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+
+	atheros {
+		compatible = "atheros,ath6kl";
+		atheros,board-id = "SD32";
+	};
+};
+
+&reset_controller {
+	compatible = "atmel,sama5d3-rstc";
+};
+
+&shutdown_controller {
+	atmel,wakeup-mode = "low";
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&main_xtal {
+	clock-frequency = <12000000>;
+};
+
+&ebi {
+	status = "okay";
+	nand_controller: nand-controller {
+		pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb &pinctrl_nand_oe_we>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x800000>;
+			rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+			cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <4>;
+			nand-ecc-step-size = <512>;
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				at91bootstrap@0 {
+					label = "at91bs";
+					reg = <0x0 0x20000>;
+				};
+
+				uboot@20000 {
+					label = "u-boot";
+					reg = <0x20000 0x80000>;
+				};
+
+				ubootenv@a0000 {
+					label = "u-boot-env";
+					reg = <0xa0000 0x20000>;
+				};
+
+				ubootenv@c0000 {
+					label = "redund-env";
+					reg = <0xc0000 0x20000>;
+				};
+
+				kernel-a@e0000 {
+					label = "kernel-a";
+					reg = <0xe0000 0x280000>;
+				};
+
+				kernel-b@360000 {
+					label = "kernel-b";
+					reg = <0x360000 0x280000>;
+				};
+
+				rootfs-a@5e0000 {
+					label = "rootfs-a";
+					reg = <0x5e0000 0x2600000>;
+				};
+
+				rootfs-b@2be0000 {
+					label = "rootfs-b";
+					reg = <0x2be0000 0x2600000>;
+				};
+
+				user@51e0000 {
+					label = "user";
+					reg = <0x51e0000 0x2dc0000>;
+				};
+
+				logs@7fa0000 {
+					label = "logs";
+					reg = <0x7fa0000 0x60000>;
+				};
+
+			};
+		};
+	};
+};
+
+&usb0 {
+	num-ports = <2>;
+	atmel,vbus-gpio = <
+		&pioB 12 GPIO_ACTIVE_HIGH
+		&pioA 31 GPIO_ACTIVE_HIGH
+		>;
+	atmel,oc-gpio = <&pioB 13 GPIO_ACTIVE_LOW>;
+};
+
+&macb0 {
+	phy-mode = "rmii";
+};
+
+&spi0 {
+	cs-gpios = <&pioA 14 0>, <&pioA 7 0>, <0>, <0>;
+};
+
+&usb2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_board_usb2>;
+	atmel,vbus-gpio = <&pioB 11 GPIO_ACTIVE_HIGH>;
+};
+
+&mmc0 {
+	pinctrl-0 = <
+		&pinctrl_mmc0_slot0_clk_cmd_dat0
+		&pinctrl_mmc0_slot0_dat1_3>;
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+	};
+};
+
+&pinctrl {
+	usb2 {
+		pinctrl_board_usb2: usb2-board {
+			atmel,pins =
+				<AT91_PIOB 11 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;		/* PB11 gpio vbus sense, deglitch */
+		};
+	};
+};
+

arch/arm/boot/dts/at91-wb50n.dts

@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-wb50n.dts - Device Tree file for wb50n evaluation board
+ *
+ *  Copyright (C) 2018 Laird
+ *
+ */
+
+/dts-v1/;
+#include "at91-wb50n.dtsi"
+
+/ {
+	model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
+	compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		btn0@10 {
+			reg = <10>;
+			label = "BTNESC";
+			linux,code = <1>; /* ESC button */
+			gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup = <1>;
+		};
+
+		irqbtn@31 {
+			reg = <31>;
+			label = "IRQBTN";
+			linux,code = <99>; /* SysReq button */
+			gpios = <&pioE 31 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			label = "wb50n:blue:led0";
+			gpios = <&pioA 12 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led1 {
+			label = "wb50n:green:led1";
+			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led2 {
+			label = "wb50n:red:led2";
+			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&mmc0 {
+	status = "okay";
+};
+
+&macb1 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+/* On BB40 this port is labeled UART1 */
+&usart0 {
+	status = "okay";
+};
+
+/* On BB40 this port is labeled UART0 */
+&usart1 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+
+	spidev@0 {
+		compatible = "spidev";
+		reg = <0>;
+		spi-max-frequency = <8000000>;
+	};
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+

arch/arm/boot/dts/at91-wb50n.dtsi

@@ -0,0 +1,198 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-wb50n.dtsi - Device Tree include file for wb50n cpu module
+ *
+ *  Copyright (C) 2018 Laird
+ *
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+	model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
+	compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		bootargs = "ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs rw";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+};
+
+&pinctrl {
+	board {
+		pinctrl_mmc0_cd: mmc0_cd {
+			atmel,pins = <AT91_PIOC 26 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC26 GPIO with pullup deglitch */
+		};
+
+		pinctrl_usba_vbus: usba_vbus {
+			atmel,pins = <AT91_PIOB 13 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB13 GPIO with deglitch */
+		};
+	};
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&main_xtal {
+	clock-frequency = <12000000>;
+};
+
+&slow_osc {
+	atmel,osc-bypass;
+};
+
+&usart1_clk {
+	atmel,clk-output-range = <0 132000000>;
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+	cd-gpios = <&pioC 26 GPIO_ACTIVE_LOW>;
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
+	status = "okay";
+	atheros@0 {
+		compatible = "atheros,ath6kl";
+		atheros,board-id = "SD32";
+		reg = <0>;
+		bus-width = <4>;
+	};
+};
+
+&macb1 {
+	phy-mode = "rmii";
+};
+
+&dbgu {
+	dmas = <0>, <0>;	/*  Do not use DMA for dbgu */
+};
+
+/* On BB40 this port is labeled UART1 */
+&usart0 {
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>;
+};
+
+/* On BB40 this port is labeled UART0 */
+&usart1 {
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+	dtr-gpios = <&pioD 13 GPIO_ACTIVE_LOW>;
+	dsr-gpios = <&pioD 11 GPIO_ACTIVE_LOW>;
+	dcd-gpios = <&pioD 7 GPIO_ACTIVE_LOW>;
+	rng-gpios = <&pioD 8 GPIO_ACTIVE_LOW>;
+};
+
+/* USART3 is direct-connect to the Bluetooth UART on the radio SIP */
+&usart3 {
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>;
+	status = "okay";
+};
+
+&spi1 {
+	cs-gpios = <&pioC 25 0>, <0>, <0>, <0>;
+};
+
+&ebi {
+	pinctrl-0 = <&pinctrl_ebi_nand_addr>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand: nand@3 {
+		reg = <0x3 0x0 0x2>;
+		atmel,rb = <0>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-on-flash-bbt;
+		label = "atmel_nand";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			at91bootstrap@0 {
+				label = "at91bs";
+				reg = <0x0 0x20000>;
+			};
+
+			uboot@20000 {
+				label = "u-boot";
+				reg = <0x20000 0x80000>;
+			};
+
+			ubootenv@a0000 {
+				label = "u-boot-env";
+				reg = <0xa0000 0x20000>;
+			};
+
+			ubootenv@c0000 {
+				label = "u-boot-env";
+				reg = <0xc0000 0x20000>;
+			};
+
+			kernel-a@e0000 {
+				label = "kernel-a";
+				reg = <0xe0000 0x500000>;
+			};
+
+			kernel-b@5e0000 {
+				label = "kernel-b";
+				reg = <0x5e0000 0x500000>;
+			};
+
+			rootfs-a@ae0000 {
+				label = "rootfs-a";
+				reg = <0xae0000 0x3000000>;
+			};
+
+			rootfs-b@3ae0000 {
+				label = "rootfs-b";
+				reg = <0x3ae0000 0x3000000>;
+			};
+
+			user@6ae0000 {
+				label = "user";
+				reg = <0x6ae0000 0x14e0000>;
+			};
+		};
+	};
+};
+
+&usb0 {
+	atmel,vbus-gpio = <&pioB 13 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+};
+
+&usb1 {
+	num-ports = <3>;
+	atmel,vbus-gpio = <&pioA 2 GPIO_ACTIVE_LOW>;
+	atmel,oc-gpio = <&pioA 4 GPIO_ACTIVE_LOW>;
+};

arch/arm/boot/dts/at91sam9261.dtsi

@@ -590,7 +590,7 @@
 			};
 
 			pmc: pmc@fffffc00 {
-				compatible = "atmel,at91rm9200-pmc", "syscon";
+				compatible = "atmel,at91sam9261-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				interrupt-controller;

arch/arm/boot/dts/at91sam9263.dtsi

@@ -93,7 +93,7 @@
 			};
 
 			pmc: pmc@fffffc00 {
-				compatible = "atmel,at91rm9200-pmc", "syscon";
+				compatible = "atmel,at91sam9263-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				interrupt-controller;

arch/arm/boot/dts/at91sam9rl.dtsi

@@ -832,7 +832,7 @@
 			};
 
 			pmc: pmc@fffffc00 {
-				compatible = "atmel,at91sam9g45-pmc", "syscon";
+				compatible = "atmel,at91sam9rl-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				interrupt-controller;

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -389,13 +389,13 @@
 				};
 			};
 
-			rstc@fffffe00 {
+			reset_controller: rstc@fffffe00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shdwc@fffffe10 {
+			shutdown_controller: shdwc@fffffe10 {
 				compatible = "atmel,at91sam9x5-shdwc";
 				reg = <0xfffffe10 0x10>;
 				clocks = <&clk32k>;
@@ -470,7 +470,7 @@
 				clock-names = "dma_clk";
 			};
 
-			pinctrl@fffff400 {
+			pinctrl: pinctrl@fffff400 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
@@ -1206,7 +1206,7 @@
 				};
 			};
 
-			watchdog@fffffe40 {
+			watchdog: watchdog@fffffe40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffe40 0x10>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;

arch/arm/boot/dts/bcm-cygnus.dtsi

@@ -41,6 +41,10 @@
 	model = "Broadcom Cygnus SoC";
 	interrupt-parent = <&gic>;
 
+	aliases {
+		ethernet0 = &eth0;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -417,6 +421,11 @@
 			status = "disabled";
 		};
 
+		rng: rng@18032000 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0x18032000 0x28>;
+		};
+
 		sdhci0: sdhci@18041000 {
 			compatible = "brcm,sdhci-iproc-cygnus";
 			reg = <0x18041000 0x100>;

arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts

@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835-rpi-cm1.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+	model = "Raspberry Pi Compute Module IO board rev1";
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "GPIO0",
+			  "GPIO1",
+			  "GPIO2",
+			  "GPIO3",
+			  "GPIO4",
+			  "GPIO5",
+			  "GPIO6",
+			  "GPIO7",
+			  "GPIO8",
+			  "GPIO9",
+			  "GPIO10",
+			  "GPIO11",
+			  "GPIO12",
+			  "GPIO13",
+			  "GPIO14",
+			  "GPIO15",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "GPIO32",
+			  "GPIO33",
+			  "GPIO34",
+			  "GPIO35",
+			  "GPIO36",
+			  "GPIO37",
+			  "GPIO38",
+			  "GPIO39",
+			  "GPIO40",
+			  "GPIO41",
+			  "GPIO42",
+			  "GPIO43",
+			  "GPIO44",
+			  "GPIO45",
+			  "HDMI_HPD_N",
+			  /* Also used as ACT LED */
+			  "EMMC_EN_N",
+			  /* Used by eMMC */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};

arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi

@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+	leds {
+		act {
+			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_3v3: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_1v8: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&sdhost {
+	non-removable;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_1v8>;
+};

arch/arm/boot/dts/bcm2837.dtsi

@@ -17,6 +17,12 @@
 		};
 	};
 
+	arm-pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupt-parent = <&local_intc>;
+		interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupt-parent = <&local_intc>;

arch/arm/boot/dts/bcm283x.dtsi

@@ -66,6 +66,12 @@
 			clock-frequency = <1000000>;
 		};
 
+		txp@7e004000 {
+			compatible = "brcm,bcm2835-txp";
+			reg = <0x7e004000 0x20>;
+			interrupts = <1 11>;
+		};
+
 		dma: dma@7e007000 {
 			compatible = "brcm,bcm2835-dma";
 			reg = <0x7e007000 0xf00>;

arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts

@@ -90,3 +90,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts

@@ -80,3 +80,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts

@@ -146,3 +146,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts

@@ -38,3 +38,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts

@@ -57,3 +57,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts

@@ -64,3 +64,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4708-netgear-r6250.dts

@@ -91,3 +91,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts

@@ -83,3 +83,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts

@@ -158,3 +158,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts

@@ -74,3 +74,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts

@@ -118,3 +118,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts

@@ -104,3 +104,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts

@@ -57,3 +57,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts

@@ -105,3 +105,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts

@@ -99,3 +99,7 @@
 &usb2 {
 	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts

@@ -62,3 +62,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts

@@ -127,3 +127,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4709-linksys-ea9200.dts

@@ -39,3 +39,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4709-netgear-r7000.dts

@@ -101,3 +101,7 @@
 &usb3 {
 	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4709-netgear-r8000.dts

@@ -182,3 +182,7 @@
 &usb3 {
 	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts

@@ -104,3 +104,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts

@@ -115,3 +115,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47094-linksys-panamera.dts

@@ -31,5 +31,238 @@
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
+
+		rfkill {
+				label = "WiFi";
+				linux,code = <KEY_RFKILL>;
+				gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
+		};
+
+		reset {
+				label = "Reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wps {
+			label = "bcm53xx:white:wps";
+			gpios = <&chipcommon 22 GPIO_ACTIVE_LOW>;
+		};
+
+		usb2 {
+			label = "bcm53xx:green:usb2";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port2>, <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		usb3 {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		power {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		wifi-disabled {
+			label = "bcm53xx:amber:wifi-disabled";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi-enabled {
+			label = "bcm53xx:white:wifi-enabled";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		bluebar1 {
+			label = "bcm53xx:white:bluebar1";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		bluebar2 {
+			label = "bcm53xx:white:bluebar2";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		bluebar3 {
+			label = "bcm53xx:white:bluebar3";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+
+		bluebar4 {
+			label = "bcm53xx:white:bluebar4";
+			gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+		};
+
+		bluebar5 {
+			label = "bcm53xx:white:bluebar5";
+			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
+		};
+
+		bluebar6 {
+			label = "bcm53xx:white:bluebar6";
+			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
+		};
+
+		bluebar7 {
+			label = "bcm53xx:white:bluebar7";
+			gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
+		};
+
+		bluebar8 {
+			label = "bcm53xx:white:bluebar8";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	mdio-bus-mux {
+		/* BIT(9) = 1 => external mdio */
+		mdio_ext: mdio@200 {
+			reg = <0x200>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	mdio-mii-mux {
+		compatible = "mdio-mux-mmioreg";
+		mdio-parent-bus = <&mdio_ext>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x1800c1c0 0x4>;
+
+		/* BIT(6) = mdc, BIT(7) = mdio */
+		mux-mask = <0xc0>;
+
+		mdio-mii@0 {
+			/* Enable MII function */
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch@0  {
+				compatible = "brcm,bcm53125";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+				reset-names = "robo_reset";
+				reg = <0>;
+				dsa,member = <1 0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						label = "lan1";
+					};
+
+					port@1 {
+						reg = <1>;
+						label = "lan5";
+					};
+
+					port@2 {
+						reg = <2>;
+						label = "lan2";
+					};
+
+					port@3 {
+						reg = <3>;
+						label = "lan6";
+					};
+
+					port@4 {
+						reg = <4>;
+						label = "lan3";
+					};
+
+					sw1_p8: port@8 {
+						reg = <8>;
+						ethernet = <&sw0_p0>;
+						label = "cpu";
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+				};
+			};
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
+};
+
+&srab {
+	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
+	status = "okay";
+	dsa,member = <0 0>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@1 {
+			reg = <1>;
+			label = "lan7";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan4";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan8";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "wan";
+		};
+
+		port@8 {
+			reg = <8>;
+			ethernet = <&gmac2>;
+			label = "cpu";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		sw0_p0: port@0 {
+			reg = <0>;
+			label = "extsw";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts

@@ -60,3 +60,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts

@@ -60,3 +60,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts

@@ -100,3 +100,7 @@
 &spi_nor {
 	status = "okay";
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47094-netgear-r8500.dts

@@ -91,3 +91,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47094.dtsi

@@ -7,9 +7,10 @@
 #include "bcm4708.dtsi"
 
 / {
-	usb3_phy: usb3-phy {
-		compatible = "brcm,ns-bx-usb3-phy";
-	};
+};
+
+&usb3_phy {
+	compatible = "brcm,ns-bx-usb3-phy";
 };
 
 &uart0 {

arch/arm/boot/dts/bcm5301x.dtsi

@@ -154,13 +154,6 @@
 		clock-names = "phy-ref-clk";
 	};
 
-	usb3_phy: usb3-phy {
-		compatible = "brcm,ns-ax-usb3-phy";
-		reg = <0x18105000 0x1000>, <0x18003000 0x1000>;
-		reg-names = "dmp", "ccb-mii";
-		#phy-cells = <0>;
-	};
-
 	axi@18000000 {
 		compatible = "brcm,bus-axi";
 		reg = <0x18000000 0x1000>;
@@ -359,7 +352,33 @@
 		reg = <0x18003000 0x8>;
 		#size-cells = <1>;
 		#address-cells = <0>;
-		status = "disabled";
+	};
+
+	mdio-bus-mux {
+		compatible = "mdio-mux-mmioreg";
+		mdio-parent-bus = <&mdio>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x18003000 0x4>;
+		mux-mask = <0x200>;
+
+		mdio@0 {
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usb3_phy: usb3-phy@10 {
+				compatible = "brcm,ns-ax-usb3-phy";
+				reg = <0x10>;
+				usb3-dmp-syscon = <&usb3_dmp>;
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+	};
+
+	usb3_dmp: syscon@18105000 {
+		reg = <0x18105000 0x1000>;
 	};
 
 	i2c0: i2c@18009000 {

arch/arm/boot/dts/bcm53573.dtsi

@@ -48,6 +48,14 @@
 		};
 	};
 
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
 	clocks {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/boot/dts/bcm94708.dts

@@ -42,3 +42,7 @@
 		reg = <0x00000000 0x08000000>;
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm94709.dts

@@ -42,3 +42,7 @@
 		reg = <0x00000000 0x08000000>;
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};

arch/arm/boot/dts/bcm953012er.dts

@@ -90,3 +90,7 @@
 		};
 	};
 };
+
+&usb3_phy {
+	status = "okay";
+};