Merge tag 'imx-cleanup-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/cleanup

Merge "ARM: imx: cleanup for 3.18" from Shawn Guo:

The i.MX cleanup for 3.18:
 - Reomve a few i.MX27 and i.MX1 board files
 - Remove imx_scu_standby_enable() since core code handles scu
   standby now
 - Remove unnecessary iomux declaration
 - Remove useless sound card property from vf610-twr dts

* tag 'imx-cleanup-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx: Remove mach-mxt_td60 board file
  ARM: i.MX: Remove i.MX1 ADS board support
  ARM: dts: vf610-twr: remove useless property for sound card.
  ARM: imx: remove imx_scu_standby_enable()
  ARM: i.MX: Remove Phytec i.MX27 PCM038/PCM970 board files
  ARM: i.MX: Remove mach-cpuimx27sd board file
  ARM: imx: iomux: Do not export symbol without public declaration

Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/mfd/tc3589x.txt

@@ -0,0 +1,107 @@
+* Toshiba TC3589x multi-purpose expander
+
+The Toshiba TC3589x series are I2C-based MFD devices which may expose the
+following built-in devices: gpio, keypad, rotator (vibrator), PWM (for
+e.g. LEDs or vibrators) The included models are:
+
+- TC35890
+- TC35892
+- TC35893
+- TC35894
+- TC35895
+- TC35896
+
+Required properties:
+ - compatible : must be "toshiba,tc35890", "toshiba,tc35892", "toshiba,tc35893",
+   "toshiba,tc35894", "toshiba,tc35895" or "toshiba,tc35896"
+ - reg : I2C address of the device
+ - interrupt-parent : specifies which IRQ controller we're connected to
+ - interrupts : the interrupt on the parent the controller is connected to
+ - interrupt-controller : marks the device node as an interrupt controller
+ - #interrupt-cells : should be <1>, the first cell is the IRQ offset on this
+   TC3589x interrupt controller.
+
+Optional nodes:
+
+- GPIO
+  This GPIO module inside the TC3589x has 24 (TC35890, TC35892) or 20
+  (other models) GPIO lines.
+ - compatible : must be "toshiba,tc3589x-gpio"
+ - interrupts : interrupt on the parent, which must be the tc3589x MFD device
+ - interrupt-controller : marks the device node as an interrupt controller
+ - #interrupt-cells : should be <2>, the first cell is the IRQ offset on this
+   TC3589x GPIO interrupt controller, the second cell is the interrupt flags
+   in accordance with <dt-bindings/interrupt-controller/irq.h>. The following
+   flags are valid:
+   - IRQ_TYPE_LEVEL_LOW
+   - IRQ_TYPE_LEVEL_HIGH
+   - IRQ_TYPE_EDGE_RISING
+   - IRQ_TYPE_EDGE_FALLING
+   - IRQ_TYPE_EDGE_BOTH
+ - gpio-controller : marks the device node as a GPIO controller
+ - #gpio-cells : should be <2>, the first cell is the GPIO offset on this
+   GPIO controller, the second cell is the flags.
+
+- Keypad
+  This keypad is the same on all variants, supporting up to 96 different
+  keys. The linux-specific properties are modeled on those already existing
+  in other input drivers.
+ - compatible : must be "toshiba,tc3589x-keypad"
+ - debounce-delay-ms : debounce interval in milliseconds
+ - keypad,num-rows : number of rows in the matrix, see
+   bindings/input/matrix-keymap.txt
+ - keypad,num-columns : number of columns in the matrix, see
+   bindings/input/matrix-keymap.txt
+ - linux,keymap: the definition can be found in
+   bindings/input/matrix-keymap.txt
+ - linux,no-autorepeat: do no enable autorepeat feature.
+ - linux,wakeup: use any event on keypad as wakeup event.
+
+Example:
+
+tc35893@44 {
+	compatible = "toshiba,tc35893";
+	reg = <0x44>;
+	interrupt-parent = <&gpio6>;
+	interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+
+	interrupt-controller;
+	#interrupt-cells = <1>;
+
+	tc3589x_gpio {
+		compatible = "toshiba,tc3589x-gpio";
+		interrupts = <0>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+	tc3589x_keypad {
+		compatible = "toshiba,tc3589x-keypad";
+		interrupts = <6>;
+		debounce-delay-ms = <4>;
+		keypad,num-columns = <8>;
+		keypad,num-rows = <8>;
+		linux,no-autorepeat;
+		linux,wakeup;
+		linux,keymap = <0x0301006b
+				0x04010066
+				0x06040072
+				0x040200d7
+				0x0303006a
+				0x0205000e
+				0x0607008b
+				0x0500001c
+				0x0403000b
+				0x03040034
+				0x05020067
+				0x0305006c
+				0x040500e7
+				0x0005009e
+				0x06020073
+				0x01030039
+				0x07060069
+				0x050500d9>;
+	};
+};

Documentation/devicetree/bindings/mtd/gpmc-nand.txt

@@ -22,7 +22,7 @@ Optional properties:
 				width of 8 is assumed.
 
  - ti,nand-ecc-opt:		A string setting the ECC layout to use. One of:
-		"sw"		<deprecated> use "ham1" instead
+		"sw"		1-bit Hamming ecc code via software
 		"hw"		<deprecated> use "ham1" instead
 		"hw-romcode"	<deprecated> use "ham1" instead
 		"ham1"		1-bit Hamming ecc code

Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt

@@ -62,7 +62,7 @@ Example:
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
-		interrupts = <0 32 0x4>;
+		interrupts = <0 16 0x4>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&gsbi5_uart_default>;

Documentation/dma-buf-sharing.txt

@@ -56,10 +56,10 @@ The dma_buf buffer sharing API usage contains the following steps:
 				     size_t size, int flags,
 				     const char *exp_name)
 
-   If this succeeds, dma_buf_export allocates a dma_buf structure, and returns a
-   pointer to the same. It also associates an anonymous file with this buffer,
-   so it can be exported. On failure to allocate the dma_buf object, it returns
-   NULL.
+   If this succeeds, dma_buf_export_named allocates a dma_buf structure, and
+   returns a pointer to the same. It also associates an anonymous file with this
+   buffer, so it can be exported. On failure to allocate the dma_buf object,
+   it returns NULL.
 
    'exp_name' is the name of exporter - to facilitate information while
    debugging.
@@ -76,7 +76,7 @@ The dma_buf buffer sharing API usage contains the following steps:
    drivers and/or processes.
 
    Interface:
-      int dma_buf_fd(struct dma_buf *dmabuf)
+      int dma_buf_fd(struct dma_buf *dmabuf, int flags)
 
    This API installs an fd for the anonymous file associated with this buffer;
    returns either 'fd', or error.
@@ -157,7 +157,9 @@ to request use of buffer for allocation.
    "dma_buf->ops->" indirection from the users of this interface.
 
    In struct dma_buf_ops, unmap_dma_buf is defined as
-      void (*unmap_dma_buf)(struct dma_buf_attachment *, struct sg_table *);
+      void (*unmap_dma_buf)(struct dma_buf_attachment *,
+                            struct sg_table *,
+                            enum dma_data_direction);
 
    unmap_dma_buf signifies the end-of-DMA for the attachment provided. Like
    map_dma_buf, this API also must be implemented by the exporter.

Documentation/kdump/kdump.txt

@@ -18,7 +18,7 @@ memory image to a dump file on the local disk, or across the network to
 a remote system.
 
 Kdump and kexec are currently supported on the x86, x86_64, ppc64, ia64,
-and s390x architectures.
+s390x and arm architectures.
 
 When the system kernel boots, it reserves a small section of memory for
 the dump-capture kernel. This ensures that ongoing Direct Memory Access
@@ -112,7 +112,7 @@ There are two possible methods of using Kdump.
 2) Or use the system kernel binary itself as dump-capture kernel and there is
    no need to build a separate dump-capture kernel. This is possible
    only with the architectures which support a relocatable kernel. As
-   of today, i386, x86_64, ppc64 and ia64 architectures support relocatable
+   of today, i386, x86_64, ppc64, ia64 and arm architectures support relocatable
    kernel.
 
 Building a relocatable kernel is advantageous from the point of view that
@@ -241,6 +241,13 @@ Dump-capture kernel config options (Arch Dependent, ia64)
   kernel will be aligned to 64Mb, so if the start address is not then
   any space below the alignment point will be wasted.
 
+Dump-capture kernel config options (Arch Dependent, arm)
+----------------------------------------------------------
+
+-   To use a relocatable kernel,
+    Enable "AUTO_ZRELADDR" support under "Boot" options:
+
+    AUTO_ZRELADDR=y
 
 Extended crashkernel syntax
 ===========================
@@ -256,6 +263,10 @@ The syntax is:
     crashkernel=<range1>:<size1>[,<range2>:<size2>,...][@offset]
     range=start-[end]
 
+Please note, on arm, the offset is required.
+    crashkernel=<range1>:<size1>[,<range2>:<size2>,...]@offset
+    range=start-[end]
+
     'start' is inclusive and 'end' is exclusive.
 
 For example:
@@ -296,6 +307,12 @@ Boot into System Kernel
    on the memory consumption of the kdump system. In general this is not
    dependent on the memory size of the production system.
 
+   On arm, use "crashkernel=Y@X". Note that the start address of the kernel
+   will be aligned to 128MiB (0x08000000), so if the start address is not then
+   any space below the alignment point may be overwritten by the dump-capture kernel,
+   which means it is possible that the vmcore is not that precise as expected.
+
+
 Load the Dump-capture Kernel
 ============================
 
@@ -315,7 +332,8 @@ For ia64:
 	- Use vmlinux or vmlinuz.gz
 For s390x:
 	- Use image or bzImage
-
+For arm:
+	- Use zImage
 
 If you are using a uncompressed vmlinux image then use following command
 to load dump-capture kernel.
@@ -331,6 +349,15 @@ to load dump-capture kernel.
    --initrd=<initrd-for-dump-capture-kernel> \
    --append="root=<root-dev> <arch-specific-options>"
 
+If you are using a compressed zImage, then use following command
+to load dump-capture kernel.
+
+   kexec --type zImage -p <dump-capture-kernel-bzImage> \
+   --initrd=<initrd-for-dump-capture-kernel> \
+   --dtb=<dtb-for-dump-capture-kernel> \
+   --append="root=<root-dev> <arch-specific-options>"
+
+
 Please note, that --args-linux does not need to be specified for ia64.
 It is planned to make this a no-op on that architecture, but for now
 it should be omitted
@@ -347,6 +374,9 @@ For ppc64:
 For s390x:
 	"1 maxcpus=1 cgroup_disable=memory"
 
+For arm:
+	"1 maxcpus=1 reset_devices"
+
 Notes on loading the dump-capture kernel:
 
 * By default, the ELF headers are stored in ELF64 format to support

Documentation/this_cpu_ops.txt

@@ -2,26 +2,26 @@ this_cpu operations
 -------------------
 
 this_cpu operations are a way of optimizing access to per cpu
-variables associated with the *currently* executing processor through
-the use of segment registers (or a dedicated register where the cpu
-permanently stored the beginning of the per cpu area for a specific
-processor).
+variables associated with the *currently* executing processor. This is
+done through the use of segment registers (or a dedicated register where
+the cpu permanently stored the beginning of the per cpu	area for a
+specific processor).
 
-The this_cpu operations add a per cpu variable offset to the processor
-specific percpu base and encode that operation in the instruction
+this_cpu operations add a per cpu variable offset to the processor
+specific per cpu base and encode that operation in the instruction
 operating on the per cpu variable.
 
-This means there are no atomicity issues between the calculation of
+This means that there are no atomicity issues between the calculation of
 the offset and the operation on the data. Therefore it is not
-necessary to disable preempt or interrupts to ensure that the
+necessary to disable preemption or interrupts to ensure that the
 processor is not changed between the calculation of the address and
 the operation on the data.
 
 Read-modify-write operations are of particular interest. Frequently
 processors have special lower latency instructions that can operate
-without the typical synchronization overhead but still provide some
-sort of relaxed atomicity guarantee. The x86 for example can execute
-RMV (Read Modify Write) instructions like inc/dec/cmpxchg without the
+without the typical synchronization overhead, but still provide some
+sort of relaxed atomicity guarantees. The x86, for example, can execute
+RMW (Read Modify Write) instructions like inc/dec/cmpxchg without the
 lock prefix and the associated latency penalty.
 
 Access to the variable without the lock prefix is not synchronized but
@@ -30,6 +30,38 @@ data specific to the currently executing processor. Only the current
 processor should be accessing that variable and therefore there are no
 concurrency issues with other processors in the system.
 
+Please note that accesses by remote processors to a per cpu area are
+exceptional situations and may impact performance and/or correctness
+(remote write operations) of local RMW operations via this_cpu_*.
+
+The main use of the this_cpu operations has been to optimize counter
+operations.
+
+The following this_cpu() operations with implied preemption protection
+are defined. These operations can be used without worrying about
+preemption and interrupts.
+
+	this_cpu_add()
+	this_cpu_read(pcp)
+	this_cpu_write(pcp, val)
+	this_cpu_add(pcp, val)
+	this_cpu_and(pcp, val)
+	this_cpu_or(pcp, val)
+	this_cpu_add_return(pcp, val)
+	this_cpu_xchg(pcp, nval)
+	this_cpu_cmpxchg(pcp, oval, nval)
+	this_cpu_cmpxchg_double(pcp1, pcp2, oval1, oval2, nval1, nval2)
+	this_cpu_sub(pcp, val)
+	this_cpu_inc(pcp)
+	this_cpu_dec(pcp)
+	this_cpu_sub_return(pcp, val)
+	this_cpu_inc_return(pcp)
+	this_cpu_dec_return(pcp)
+
+
+Inner working of this_cpu operations
+------------------------------------
+
 On x86 the fs: or the gs: segment registers contain the base of the
 per cpu area. It is then possible to simply use the segment override
 to relocate a per cpu relative address to the proper per cpu area for
@@ -48,22 +80,21 @@ results in a single instruction
 	mov ax, gs:[x]
 
 instead of a sequence of calculation of the address and then a fetch
-from that address which occurs with the percpu operations. Before
+from that address which occurs with the per cpu operations. Before
 this_cpu_ops such sequence also required preempt disable/enable to
 prevent the kernel from moving the thread to a different processor
 while the calculation is performed.
 
-The main use of the this_cpu operations has been to optimize counter
-operations.
+Consider the following this_cpu operation:
 
 	this_cpu_inc(x)
 
-results in the following single instruction (no lock prefix!)
+The above results in the following single instruction (no lock prefix!)
 
 	inc gs:[x]
 
 instead of the following operations required if there is no segment
-register.
+register:
 
 	int *y;
 	int cpu;
@@ -73,10 +104,10 @@ register.
 	(*y)++;
 	put_cpu();
 
-Note that these operations can only be used on percpu data that is
+Note that these operations can only be used on per cpu data that is
 reserved for a specific processor. Without disabling preemption in the
 surrounding code this_cpu_inc() will only guarantee that one of the
-percpu counters is correctly incremented. However, there is no
+per cpu counters is correctly incremented. However, there is no
 guarantee that the OS will not move the process directly before or
 after the this_cpu instruction is executed. In general this means that
 the value of the individual counters for each processor are
@@ -86,9 +117,9 @@ that is of interest.
 Per cpu variables are used for performance reasons. Bouncing cache
 lines can be avoided if multiple processors concurrently go through
 the same code paths.  Since each processor has its own per cpu
-variables no concurrent cacheline updates take place. The price that
+variables no concurrent cache line updates take place. The price that
 has to be paid for this optimization is the need to add up the per cpu
-counters when the value of the counter is needed.
+counters when the value of a counter is needed.
 
 
 Special operations:
@@ -100,33 +131,39 @@ Takes the offset of a per cpu variable (&x !) and returns the address
 of the per cpu variable that belongs to the currently executing
 processor.  this_cpu_ptr avoids multiple steps that the common
 get_cpu/put_cpu sequence requires. No processor number is
-available. Instead the offset of the local per cpu area is simply
-added to the percpu offset.
+available. Instead, the offset of the local per cpu area is simply
+added to the per cpu offset.
 
+Note that this operation is usually used in a code segment when
+preemption has been disabled. The pointer is then used to
+access local per cpu data in a critical section. When preemption
+is re-enabled this pointer is usually no longer useful since it may
+no longer point to per cpu data of the current processor.
 
 
 Per cpu variables and offsets
 -----------------------------
 
-Per cpu variables have *offsets* to the beginning of the percpu
+Per cpu variables have *offsets* to the beginning of the per cpu
 area. They do not have addresses although they look like that in the
 code. Offsets cannot be directly dereferenced. The offset must be
-added to a base pointer of a percpu area of a processor in order to
+added to a base pointer of a per cpu area of a processor in order to
 form a valid address.
 
 Therefore the use of x or &x outside of the context of per cpu
 operations is invalid and will generally be treated like a NULL
 pointer dereference.
 
-In the context of per cpu operations
+	DEFINE_PER_CPU(int, x);
 
-	x is a per cpu variable. Most this_cpu operations take a cpu
-	variable.
+In the context of per cpu operations the above implies that x is a per
+cpu variable. Most this_cpu operations take a cpu variable.
 
-	&x is the *offset* a per cpu variable. this_cpu_ptr() takes
-	the offset of a per cpu variable which makes this look a bit
-	strange.
+	int __percpu *p = &x;
 
+&x and hence p is the *offset* of a per cpu variable. this_cpu_ptr()
+takes the offset of a per cpu variable which makes this look a bit
+strange.
 
 
 Operations on a field of a per cpu structure
@@ -152,7 +189,7 @@ If we have an offset to struct s:
 
 	struct s __percpu *ps = &p;
 
-	z = this_cpu_dec(ps->m);
+	this_cpu_dec(ps->m);
 
 	z = this_cpu_inc_return(ps->n);
 
@@ -172,29 +209,52 @@ if we do not make use of this_cpu ops later to manipulate fields:
 Variants of this_cpu ops
 -------------------------
 
-this_cpu ops are interrupt safe. Some architecture do not support
+this_cpu ops are interrupt safe. Some architectures do not support
 these per cpu local operations. In that case the operation must be
 replaced by code that disables interrupts, then does the operations
-that are guaranteed to be atomic and then reenable interrupts. Doing
+that are guaranteed to be atomic and then re-enable interrupts. Doing
 so is expensive. If there are other reasons why the scheduler cannot
 change the processor we are executing on then there is no reason to
-disable interrupts. For that purpose the __this_cpu operations are
-provided. For example.
-
-	__this_cpu_inc(x);
-
-Will increment x and will not fallback to code that disables
+disable interrupts. For that purpose the following __this_cpu operations
+are provided.
+
+These operations have no guarantee against concurrent interrupts or
+preemption. If a per cpu variable is not used in an interrupt context
+and the scheduler cannot preempt, then they are safe. If any interrupts
+still occur while an operation is in progress and if the interrupt too
+modifies the variable, then RMW actions can not be guaranteed to be
+safe.
+
+	__this_cpu_add()
+	__this_cpu_read(pcp)
+	__this_cpu_write(pcp, val)
+	__this_cpu_add(pcp, val)
+	__this_cpu_and(pcp, val)
+	__this_cpu_or(pcp, val)
+	__this_cpu_add_return(pcp, val)
+	__this_cpu_xchg(pcp, nval)
+	__this_cpu_cmpxchg(pcp, oval, nval)
+	__this_cpu_cmpxchg_double(pcp1, pcp2, oval1, oval2, nval1, nval2)
+	__this_cpu_sub(pcp, val)
+	__this_cpu_inc(pcp)
+	__this_cpu_dec(pcp)
+	__this_cpu_sub_return(pcp, val)
+	__this_cpu_inc_return(pcp)
+	__this_cpu_dec_return(pcp)
+
+
+Will increment x and will not fall-back to code that disables
 interrupts on platforms that cannot accomplish atomicity through
 address relocation and a Read-Modify-Write operation in the same
 instruction.
 
 
-
 &this_cpu_ptr(pp)->n vs this_cpu_ptr(&pp->n)
 --------------------------------------------
 
 The first operation takes the offset and forms an address and then
-adds the offset of the n field.
+adds the offset of the n field. This may result in two add
+instructions emitted by the compiler.
 
 The second one first adds the two offsets and then does the
 relocation.  IMHO the second form looks cleaner and has an easier time
@@ -202,4 +262,73 @@ with (). The second form also is consistent with the way
 this_cpu_read() and friends are used.
 
 
-Christoph Lameter, April 3rd, 2013
+Remote access to per cpu data
+------------------------------
+
+Per cpu data structures are designed to be used by one cpu exclusively.
+If you use the variables as intended, this_cpu_ops() are guaranteed to
+be "atomic" as no other CPU has access to these data structures.
+
+There are special cases where you might need to access per cpu data
+structures remotely. It is usually safe to do a remote read access
+and that is frequently done to summarize counters. Remote write access
+something which could be problematic because this_cpu ops do not
+have lock semantics. A remote write may interfere with a this_cpu
+RMW operation.
+
+Remote write accesses to percpu data structures are highly discouraged
+unless absolutely necessary. Please consider using an IPI to wake up
+the remote CPU and perform the update to its per cpu area.
+
+To access per-cpu data structure remotely, typically the per_cpu_ptr()
+function is used:
+
+
+	DEFINE_PER_CPU(struct data, datap);
+
+	struct data *p = per_cpu_ptr(&datap, cpu);
+
+This makes it explicit that we are getting ready to access a percpu
+area remotely.
+
+You can also do the following to convert the datap offset to an address
+
+	struct data *p = this_cpu_ptr(&datap);
+
+but, passing of pointers calculated via this_cpu_ptr to other cpus is
+unusual and should be avoided.
+
+Remote access are typically only for reading the status of another cpus
+per cpu data. Write accesses can cause unique problems due to the
+relaxed synchronization requirements for this_cpu operations.
+
+One example that illustrates some concerns with write operations is
+the following scenario that occurs because two per cpu variables
+share a cache-line but the relaxed synchronization is applied to
+only one process updating the cache-line.
+
+Consider the following example
+
+
+	struct test {
+		atomic_t a;
+		int b;
+	};
+
+	DEFINE_PER_CPU(struct test, onecacheline);
+
+There is some concern about what would happen if the field 'a' is updated
+remotely from one processor and the local processor would use this_cpu ops
+to update field b. Care should be taken that such simultaneous accesses to
+data within the same cache line are avoided. Also costly synchronization
+may be necessary. IPIs are generally recommended in such scenarios instead
+of a remote write to the per cpu area of another processor.
+
+Even in cases where the remote writes are rare, please bear in
+mind that a remote write will evict the cache line from the processor
+that most likely will access it. If the processor wakes up and finds a
+missing local cache line of a per cpu area, its performance and hence
+the wake up times will be affected.
+
+Christoph Lameter, August 4th, 2014
+Pranith Kumar, Aug 2nd, 2014

MAINTAINERS

@@ -1279,8 +1279,13 @@ M:	Heiko Stuebner <heiko@sntech.de>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	linux-rockchip@lists.infradead.org
 S:	Maintained
+F:	arch/arm/boot/dts/rk3*
 F:	arch/arm/mach-rockchip/
+F:	drivers/clk/rockchip/
+F:	drivers/i2c/busses/i2c-rk3x.c
 F:	drivers/*/*rockchip*
+F:	drivers/*/*/*rockchip*
+F:	sound/soc/rockchip/
 
 ARM/SAMSUNG ARM ARCHITECTURES
 M:	Ben Dooks <ben-linux@fluff.org>
@@ -9557,6 +9562,14 @@ S:	Maintained
 F:	Documentation/usb/ohci.txt
 F:	drivers/usb/host/ohci*
 
+USB OVER IP DRIVER
+M:	Valentina Manea <valentina.manea.m@gmail.com>
+M:	Shuah Khan <shuah.kh@samsung.com>
+L:	linux-usb@vger.kernel.org
+S:	Maintained
+F:	drivers/usb/usbip/
+F:	tools/usb/usbip/
+
 USB PEGASUS DRIVER
 M:	Petko Manolov <petkan@nucleusys.com>
 L:	linux-usb@vger.kernel.org

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 17
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
 NAME = Shuffling Zombie Juror
 
 # *DOCUMENTATION*

arch/alpha/include/asm/io.h

@@ -500,10 +500,14 @@ extern inline void writeq(u64 b, volatile void __iomem *addr)
 #define outb_p		outb
 #define outw_p		outw
 #define outl_p		outl
-#define readb_relaxed(addr) __raw_readb(addr)
-#define readw_relaxed(addr) __raw_readw(addr)
-#define readl_relaxed(addr) __raw_readl(addr)
-#define readq_relaxed(addr) __raw_readq(addr)
+#define readb_relaxed(addr)	__raw_readb(addr)
+#define readw_relaxed(addr)	__raw_readw(addr)
+#define readl_relaxed(addr)	__raw_readl(addr)
+#define readq_relaxed(addr)	__raw_readq(addr)
+#define writeb_relaxed(b, addr)	__raw_writeb(b, addr)
+#define writew_relaxed(b, addr)	__raw_writew(b, addr)
+#define writel_relaxed(b, addr)	__raw_writel(b, addr)
+#define writeq_relaxed(b, addr)	__raw_writeq(b, addr)
 
 #define mmiowb()
 

arch/alpha/include/asm/unistd.h

@@ -3,7 +3,7 @@
 
 #include <uapi/asm/unistd.h>
 
-#define NR_SYSCALLS			508
+#define NR_SYSCALLS			511
 
 #define __ARCH_WANT_OLD_READDIR
 #define __ARCH_WANT_STAT64

arch/alpha/include/uapi/asm/unistd.h

@@ -469,5 +469,8 @@
 #define __NR_process_vm_writev		505
 #define __NR_kcmp			506
 #define __NR_finit_module		507
+#define __NR_sched_setattr		508
+#define __NR_sched_getattr		509
+#define __NR_renameat2			510
 
 #endif /* _UAPI_ALPHA_UNISTD_H */

arch/alpha/kernel/systbls.S

@@ -526,6 +526,9 @@ sys_call_table:
 	.quad sys_process_vm_writev		/* 505 */
 	.quad sys_kcmp
 	.quad sys_finit_module
+	.quad sys_sched_setattr
+	.quad sys_sched_getattr
+	.quad sys_renameat2			/* 510 */
 
 	.size sys_call_table, . - sys_call_table
 	.type sys_call_table, @object

arch/arc/mm/cache_arc700.c

@@ -581,6 +581,7 @@ void flush_icache_range(unsigned long kstart, unsigned long kend)
 		tot_sz -= sz;
 	}
 }
+EXPORT_SYMBOL(flush_icache_range);
 
 /*
  * General purpose helper to make I and D cache lines consistent.

arch/arm/Kconfig

@@ -1985,8 +1985,6 @@ config XIP_PHYS_ADDR
 config KEXEC
 	bool "Kexec system call (EXPERIMENTAL)"
 	depends on (!SMP || PM_SLEEP_SMP)
-	select CRYPTO
-	select CRYPTO_SHA256
 	help
 	  kexec is a system call that implements the ability to shutdown your
 	  current kernel, and to start another kernel.  It is like a reboot

arch/arm/boot/dts/dra7.dtsi

@@ -245,7 +245,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio2: gpio@48055000 {
@@ -256,7 +256,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio3: gpio@48057000 {
@@ -267,7 +267,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio4: gpio@48059000 {
@@ -278,7 +278,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio5: gpio@4805b000 {
@@ -289,7 +289,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio6: gpio@4805d000 {
@@ -300,7 +300,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio7: gpio@48051000 {
@@ -311,7 +311,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio8: gpio@48053000 {
@@ -322,7 +322,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		uart1: serial@4806a000 {

arch/arm/boot/dts/imx53-qsrb.dts

@@ -28,6 +28,12 @@
 				MX53_PAD_CSI0_DAT9__I2C1_SCL      0x400001ec
 			>;
 		};
+
+		pinctrl_pmic: pmicgrp {
+			fsl,pins = <
+				MX53_PAD_CSI0_DAT5__GPIO5_23	0x1e4 /* IRQ */
+			>;
+		};
 	};
 };
 
@@ -38,6 +44,8 @@
 
 	pmic: mc34708@8 {
 		compatible = "fsl,mc34708";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
 		reg = <0x08>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <23 0x8>;

arch/arm/boot/dts/imx6dl-hummingboard.dts

@@ -58,7 +58,7 @@
 
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
-		model = "imx-spdif";
+		model = "On-board SPDIF";
 		/* IMX6 doesn't implement this yet */
 		spdif-controller = <&spdif>;
 		spdif-out;
@@ -181,11 +181,13 @@
 };
 
 &usbh1 {
+	disable-over-current;
 	vbus-supply = <&reg_usbh1_vbus>;
 	status = "okay";
 };
 
 &usbotg {
+	disable-over-current;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
 	vbus-supply = <&reg_usbotg_vbus>;

arch/arm/boot/dts/imx6qdl-cubox-i.dtsi

@@ -61,7 +61,7 @@
 
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
-		model = "imx-spdif";
+		model = "Integrated SPDIF";
 		/* IMX6 doesn't implement this yet */
 		spdif-controller = <&spdif>;
 		spdif-out;
@@ -130,16 +130,23 @@
 			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
 		};
 
+		pinctrl_cubox_i_usbh1: cubox-i-usbh1 {
+			fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>;
+		};
+
 		pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
 			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
 		};
 
-		pinctrl_cubox_i_usbotg_id: cubox-i-usbotg-id {
+		pinctrl_cubox_i_usbotg: cubox-i-usbotg {
 			/*
-			 * The Cubox-i pulls this low, but as it's pointless
+			 * The Cubox-i pulls ID low, but as it's pointless
 			 * leaving it as a pull-up, even if it is just 10uA.
 			 */
-			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+				MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+			>;
 		};
 
 		pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
@@ -173,13 +180,15 @@
 };
 
 &usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_usbh1>;
 	vbus-supply = <&reg_usbh1_vbus>;
 	status = "okay";
 };
 
 &usbotg {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_cubox_i_usbotg_id>;
+	pinctrl-0 = <&pinctrl_cubox_i_usbotg>;
 	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi

@@ -17,7 +17,7 @@
 	enet {
 		pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
 			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b8b0
 				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
 				/* AR8035 reset */
 				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x130b0

arch/arm/boot/dts/omap3-beagle.dts

@@ -292,6 +292,7 @@
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins>;
+	interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
 };
 
 &gpio1 {

arch/arm/boot/dts/omap3-n900.dts

@@ -353,7 +353,7 @@
 	};
 
 	twl_power: power {
-		compatible = "ti,twl4030-power-n900";
+		compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
 		ti,use_poweroff;
 	};
 };

arch/arm/boot/dts/omap3430-sdp.dts

@@ -107,7 +107,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <1 0 0x08000000>;
-		ti,nand-ecc-opt = "ham1";
+		ti,nand-ecc-opt = "sw";
 		nand-bus-width = <8>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <36>;

arch/arm/boot/dts/omap54xx-clocks.dtsi

@@ -367,10 +367,12 @@
 
 	l3_iclk_div: l3_iclk_div {
 		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
+		compatible = "ti,divider-clock";
+		ti,max-div = <2>;
+		ti,bit-shift = <4>;
+		reg = <0x100>;
 		clocks = <&dpll_core_h12x2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
+		ti,index-power-of-two;
 	};
 
 	gpu_l3_iclk: gpu_l3_iclk {
@@ -383,10 +385,12 @@
 
 	l4_root_clk_div: l4_root_clk_div {
 		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
+		compatible = "ti,divider-clock";
+		ti,max-div = <2>;
+		ti,bit-shift = <8>;
+		reg = <0x100>;
 		clocks = <&l3_iclk_div>;
-		clock-mult = <1>;
-		clock-div = <1>;
+		ti,index-power-of-two;
 	};
 
 	slimbus1_slimbus_clk: slimbus1_slimbus_clk {

arch/arm/boot/dts/twl6030.dtsi

@@ -83,10 +83,6 @@
 		regulator-always-on;
 	};
 
-	clk32kg: regulator-clk32kg {
-		compatible = "ti,twl6030-clk32kg";
-	};
-
 	twl_usb_comparator: usb-comparator {
 		compatible = "ti,twl6030-usb";
 		interrupts = <4>, <10>;

arch/arm/boot/dts/vf610-twr.dts

@@ -76,7 +76,6 @@
 
 		simple-audio-card,cpu {
 			sound-dai = <&sai2>;
-			master-clkdir-out;
 			frame-master;
 			bitclock-master;
 		};

arch/arm/configs/imx_v4_v5_defconfig

@@ -22,7 +22,6 @@ CONFIG_ARCH_MULTI_V5=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_MXC=y
 CONFIG_MXC_IRQ_PRIOR=y
-CONFIG_ARCH_MX1ADS=y
 CONFIG_MACH_SCB9328=y
 CONFIG_MACH_APF9328=y
 CONFIG_MACH_MX21ADS=y
@@ -30,10 +29,6 @@ CONFIG_MACH_MX25_3DS=y
 CONFIG_MACH_EUKREA_CPUIMX25SD=y
 CONFIG_MACH_IMX25_DT=y
 CONFIG_MACH_MX27ADS=y
-CONFIG_MACH_PCM038=y
-CONFIG_MACH_CPUIMX27=y
-CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2=y
-CONFIG_MACH_EUKREA_CPUIMX27_USEUART4=y
 CONFIG_MACH_MX27_3DS=y
 CONFIG_MACH_IMX27_VISSTRIM_M10=y
 CONFIG_MACH_PCA100=y

arch/arm/include/asm/cacheflush.h

@@ -472,7 +472,6 @@ static inline void __sync_cache_range_r(volatile void *p, size_t size)
 	"mcr	p15, 0, r0, c1, c0, 0	@ set SCTLR \n\t" \
 	"isb	\n\t" \
 	"bl	v7_flush_dcache_"__stringify(level)" \n\t" \
-	"clrex	\n\t" \
 	"mrc	p15, 0, r0, c1, c0, 1	@ get ACTLR \n\t" \
 	"bic	r0, r0, #(1 << 6)	@ disable local coherency \n\t" \
 	"mcr	p15, 0, r0, c1, c0, 1	@ set ACTLR \n\t" \

arch/arm/include/asm/cputype.h

@@ -74,6 +74,7 @@
 #define ARM_CPU_PART_CORTEX_A12		0x4100c0d0
 #define ARM_CPU_PART_CORTEX_A17		0x4100c0e0
 #define ARM_CPU_PART_CORTEX_A15		0x4100c0f0
+#define ARM_CPU_PART_MASK		0xff00fff0
 
 #define ARM_CPU_XSCALE_ARCH_MASK	0xe000
 #define ARM_CPU_XSCALE_ARCH_V1		0x2000
@@ -179,7 +180,7 @@ static inline unsigned int __attribute_const__ read_cpuid_implementor(void)
  */
 static inline unsigned int __attribute_const__ read_cpuid_part(void)
 {
-	return read_cpuid_id() & 0xff00fff0;
+	return read_cpuid_id() & ARM_CPU_PART_MASK;
 }
 
 static inline unsigned int __attribute_const__ __deprecated read_cpuid_part_number(void)

arch/arm/include/asm/elf.h

@@ -50,6 +50,7 @@ typedef struct user_fp elf_fpregset_t;
 #define R_ARM_ABS32		2
 #define R_ARM_CALL		28
 #define R_ARM_JUMP24		29
+#define R_ARM_TARGET1		38
 #define R_ARM_V4BX		40
 #define R_ARM_PREL31		42
 #define R_ARM_MOVW_ABS_NC	43

arch/arm/include/asm/smp_plat.h

@@ -8,6 +8,7 @@
 #include <linux/cpumask.h>
 #include <linux/err.h>
 
+#include <asm/cpu.h>
 #include <asm/cputype.h>
 
 /*
@@ -25,6 +26,20 @@ static inline bool is_smp(void)
 #endif
 }
 
+/**
+ * smp_cpuid_part() - return part id for a given cpu
+ * @cpu:	logical cpu id.
+ *
+ * Return: part id of logical cpu passed as argument.
+ */
+static inline unsigned int smp_cpuid_part(int cpu)
+{
+	struct cpuinfo_arm *cpu_info = &per_cpu(cpu_data, cpu);
+
+	return is_smp() ? cpu_info->cpuid & ARM_CPU_PART_MASK :
+			  read_cpuid_part();
+}
+
 /* all SMP configurations have the extended CPUID registers */
 #ifndef CONFIG_MMU
 #define tlb_ops_need_broadcast()	0

arch/arm/kernel/entry-header.S

@@ -208,26 +208,21 @@
 #endif
 	.endif
 	msr	spsr_cxsf, \rpsr
-#if defined(CONFIG_CPU_V6)
-	ldr	r0, [sp]
-	strex	r1, r2, [sp]			@ clear the exclusive monitor
-	ldmib	sp, {r1 - pc}^			@ load r1 - pc, cpsr
-#elif defined(CONFIG_CPU_32v6K)
-	clrex					@ clear the exclusive monitor
-	ldmia	sp, {r0 - pc}^			@ load r0 - pc, cpsr
-#else
-	ldmia	sp, {r0 - pc}^			@ load r0 - pc, cpsr
+#if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_32v6K)
+	@ We must avoid clrex due to Cortex-A15 erratum #830321
+	sub	r0, sp, #4			@ uninhabited address
+	strex	r1, r2, [r0]			@ clear the exclusive monitor
 #endif
+	ldmia	sp, {r0 - pc}^			@ load r0 - pc, cpsr
 	.endm
 
 	.macro	restore_user_regs, fast = 0, offset = 0
 	ldr	r1, [sp, #\offset + S_PSR]	@ get calling cpsr
 	ldr	lr, [sp, #\offset + S_PC]!	@ get pc
 	msr	spsr_cxsf, r1			@ save in spsr_svc
-#if defined(CONFIG_CPU_V6)
+#if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_32v6K)
+	@ We must avoid clrex due to Cortex-A15 erratum #830321
 	strex	r1, r2, [sp]			@ clear the exclusive monitor
-#elif defined(CONFIG_CPU_32v6K)
-	clrex					@ clear the exclusive monitor
 #endif
 	.if	\fast
 	ldmdb	sp, {r1 - lr}^			@ get calling r1 - lr
@@ -261,7 +256,10 @@
 	.endif
 	ldr	lr, [sp, #S_SP]			@ top of the stack
 	ldrd	r0, r1, [sp, #S_LR]		@ calling lr and pc
-	clrex					@ clear the exclusive monitor
+
+	@ We must avoid clrex due to Cortex-A15 erratum #830321
+	strex	r2, r1, [sp, #S_LR]		@ clear the exclusive monitor
+
 	stmdb	lr!, {r0, r1, \rpsr}		@ calling lr and rfe context
 	ldmia	sp, {r0 - r12}
 	mov	sp, lr
@@ -282,13 +280,16 @@
 	.endm
 #else	/* ifdef CONFIG_CPU_V7M */
 	.macro	restore_user_regs, fast = 0, offset = 0
-	clrex					@ clear the exclusive monitor
 	mov	r2, sp
 	load_user_sp_lr r2, r3, \offset + S_SP	@ calling sp, lr
 	ldr	r1, [sp, #\offset + S_PSR]	@ get calling cpsr
 	ldr	lr, [sp, #\offset + S_PC]	@ get pc
 	add	sp, sp, #\offset + S_SP
 	msr	spsr_cxsf, r1			@ save in spsr_svc
+
+	@ We must avoid clrex due to Cortex-A15 erratum #830321
+	strex	r1, r2, [sp]			@ clear the exclusive monitor
+
 	.if	\fast
 	ldmdb	sp, {r1 - r12}			@ get calling r1 - r12
 	.else

arch/arm/kernel/module.c

@@ -91,6 +91,7 @@ apply_relocate(Elf32_Shdr *sechdrs, const char *strtab, unsigned int symindex,
 			break;
 
 		case R_ARM_ABS32:
+		case R_ARM_TARGET1:
 			*(u32 *)loc += sym->st_value;
 			break;
 

arch/arm/mach-bcm/Makefile

@@ -36,5 +36,4 @@ obj-$(CONFIG_ARCH_BCM_5301X)	+= bcm_5301x.o
 
 ifeq ($(CONFIG_ARCH_BRCMSTB),y)
 obj-y				+= brcmstb.o
-obj-$(CONFIG_SMP)		+= headsmp-brcmstb.o platsmp-brcmstb.o
 endif

arch/arm/mach-bcm/brcmstb.h

@@ -1,19 +0,0 @@
-/*
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __BRCMSTB_H__
-#define __BRCMSTB_H__
-
-void brcmstb_secondary_startup(void);
-
-#endif /* __BRCMSTB_H__ */

arch/arm/mach-bcm/headsmp-brcmstb.S

@@ -1,33 +0,0 @@
-/*
- * SMP boot code for secondary CPUs
- * Based on arch/arm/mach-tegra/headsmp.S
- *
- * Copyright (C) 2010 NVIDIA, Inc.
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#include <asm/assembler.h>
-#include <linux/linkage.h>
-#include <linux/init.h>
-
-        .section ".text.head", "ax"
-
-ENTRY(brcmstb_secondary_startup)
-        /*
-         * Ensure CPU is in a sane state by disabling all IRQs and switching
-         * into SVC mode.
-         */
-        setmode	PSR_I_BIT | PSR_F_BIT | SVC_MODE, r0
-
-        bl      v7_invalidate_l1
-        b       secondary_startup
-ENDPROC(brcmstb_secondary_startup)

arch/arm/mach-bcm/platsmp-brcmstb.c

@@ -1,363 +0,0 @@
-/*
- * Broadcom STB CPU SMP and hotplug support for ARM
- *
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/of_address.h>
-#include <linux/of_platform.h>
-#include <linux/printk.h>
-#include <linux/regmap.h>
-#include <linux/smp.h>
-#include <linux/mfd/syscon.h>
-#include <linux/spinlock.h>
-
-#include <asm/cacheflush.h>
-#include <asm/cp15.h>
-#include <asm/mach-types.h>
-#include <asm/smp_plat.h>
-
-#include "brcmstb.h"
-
-enum {
-	ZONE_MAN_CLKEN_MASK		= BIT(0),
-	ZONE_MAN_RESET_CNTL_MASK	= BIT(1),
-	ZONE_MAN_MEM_PWR_MASK		= BIT(4),
-	ZONE_RESERVED_1_MASK		= BIT(5),
-	ZONE_MAN_ISO_CNTL_MASK		= BIT(6),
-	ZONE_MANUAL_CONTROL_MASK	= BIT(7),
-	ZONE_PWR_DN_REQ_MASK		= BIT(9),
-	ZONE_PWR_UP_REQ_MASK		= BIT(10),
-	ZONE_BLK_RST_ASSERT_MASK	= BIT(12),
-	ZONE_PWR_OFF_STATE_MASK		= BIT(25),
-	ZONE_PWR_ON_STATE_MASK		= BIT(26),
-	ZONE_DPG_PWR_STATE_MASK		= BIT(28),
-	ZONE_MEM_PWR_STATE_MASK		= BIT(29),
-	ZONE_RESET_STATE_MASK		= BIT(31),
-	CPU0_PWR_ZONE_CTRL_REG		= 1,
-	CPU_RESET_CONFIG_REG		= 2,
-};
-
-static void __iomem *cpubiuctrl_block;
-static void __iomem *hif_cont_block;
-static u32 cpu0_pwr_zone_ctrl_reg;
-static u32 cpu_rst_cfg_reg;
-static u32 hif_cont_reg;
-
-#ifdef CONFIG_HOTPLUG_CPU
-static DEFINE_PER_CPU_ALIGNED(int, per_cpu_sw_state);
-
-static int per_cpu_sw_state_rd(u32 cpu)
-{
-	sync_cache_r(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
-	return per_cpu(per_cpu_sw_state, cpu);
-}
-
-static void per_cpu_sw_state_wr(u32 cpu, int val)
-{
-	per_cpu(per_cpu_sw_state, cpu) = val;
-	dmb();
-	sync_cache_w(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
-	dsb_sev();
-}
-#else
-static inline void per_cpu_sw_state_wr(u32 cpu, int val) { }
-#endif
-
-static void __iomem *pwr_ctrl_get_base(u32 cpu)
-{
-	void __iomem *base = cpubiuctrl_block + cpu0_pwr_zone_ctrl_reg;
-	base += (cpu_logical_map(cpu) * 4);
-	return base;
-}
-
-static u32 pwr_ctrl_rd(u32 cpu)
-{
-	void __iomem *base = pwr_ctrl_get_base(cpu);
-	return readl_relaxed(base);
-}
-
-static void pwr_ctrl_wr(u32 cpu, u32 val)
-{
-	void __iomem *base = pwr_ctrl_get_base(cpu);
-	writel(val, base);
-}
-
-static void cpu_rst_cfg_set(u32 cpu, int set)
-{
-	u32 val;
-	val = readl_relaxed(cpubiuctrl_block + cpu_rst_cfg_reg);
-	if (set)
-		val |= BIT(cpu_logical_map(cpu));
-	else
-		val &= ~BIT(cpu_logical_map(cpu));
-	writel_relaxed(val, cpubiuctrl_block + cpu_rst_cfg_reg);
-}
-
-static void cpu_set_boot_addr(u32 cpu, unsigned long boot_addr)
-{
-	const int reg_ofs = cpu_logical_map(cpu) * 8;
-	writel_relaxed(0, hif_cont_block + hif_cont_reg + reg_ofs);
-	writel_relaxed(boot_addr, hif_cont_block + hif_cont_reg + 4 + reg_ofs);
-}
-
-static void brcmstb_cpu_boot(u32 cpu)
-{
-	pr_info("SMP: Booting CPU%d...\n", cpu);
-
-	/*
-	 * set the reset vector to point to the secondary_startup
-	 * routine
-	 */
-	cpu_set_boot_addr(cpu, virt_to_phys(brcmstb_secondary_startup));
-
-	/* unhalt the cpu */
-	cpu_rst_cfg_set(cpu, 0);
-}
-
-static void brcmstb_cpu_power_on(u32 cpu)
-{
-	/*
-	 * The secondary cores power was cut, so we must go through
-	 * power-on initialization.
-	 */
-	u32 tmp;
-
-	pr_info("SMP: Powering up CPU%d...\n", cpu);
-
-	/* Request zone power up */
-	pwr_ctrl_wr(cpu, ZONE_PWR_UP_REQ_MASK);
-
-	/* Wait for the power up FSM to complete */
-	do {
-		tmp = pwr_ctrl_rd(cpu);
-	} while (!(tmp & ZONE_PWR_ON_STATE_MASK));
-
-	per_cpu_sw_state_wr(cpu, 1);
-}
-
-static int brcmstb_cpu_get_power_state(u32 cpu)
-{
-	int tmp = pwr_ctrl_rd(cpu);
-	return (tmp & ZONE_RESET_STATE_MASK) ? 0 : 1;
-}
-
-#ifdef CONFIG_HOTPLUG_CPU
-
-static void brcmstb_cpu_die(u32 cpu)
-{
-	v7_exit_coherency_flush(all);
-
-	/* Prevent all interrupts from reaching this CPU. */
-	arch_local_irq_disable();
-
-	/*
-	 * Final full barrier to ensure everything before this instruction has
-	 * quiesced.
-	 */
-	isb();
-	dsb();
-
-	per_cpu_sw_state_wr(cpu, 0);
-
-	/* Sit and wait to die */
-	wfi();
-
-	/* We should never get here... */
-	panic("Spurious interrupt on CPU %d received!\n", cpu);
-}
-
-static int brcmstb_cpu_kill(u32 cpu)
-{
-	u32 tmp;
-
-	pr_info("SMP: Powering down CPU%d...\n", cpu);
-
-	while (per_cpu_sw_state_rd(cpu))
-		;
-
-	/* Program zone reset */
-	pwr_ctrl_wr(cpu, ZONE_RESET_STATE_MASK | ZONE_BLK_RST_ASSERT_MASK |
-			      ZONE_PWR_DN_REQ_MASK);
-
-	/* Verify zone reset */
-	tmp = pwr_ctrl_rd(cpu);
-	if (!(tmp & ZONE_RESET_STATE_MASK))
-		pr_err("%s: Zone reset bit for CPU %d not asserted!\n",
-			__func__, cpu);
-
-	/* Wait for power down */
-	do {
-		tmp = pwr_ctrl_rd(cpu);
-	} while (!(tmp & ZONE_PWR_OFF_STATE_MASK));
-
-	/* Settle-time from Broadcom-internal DVT reference code */
-	udelay(7);
-
-	/* Assert reset on the CPU */
-	cpu_rst_cfg_set(cpu, 1);
-
-	return 1;
-}
-
-#endif /* CONFIG_HOTPLUG_CPU */
-
-static int __init setup_hifcpubiuctrl_regs(struct device_node *np)
-{
-	int rc = 0;
-	char *name;
-	struct device_node *syscon_np = NULL;
-
-	name = "syscon-cpu";
-
-	syscon_np = of_parse_phandle(np, name, 0);
-	if (!syscon_np) {
-		pr_err("can't find phandle %s\n", name);
-		rc = -EINVAL;
-		goto cleanup;
-	}
-
-	cpubiuctrl_block = of_iomap(syscon_np, 0);
-	if (!cpubiuctrl_block) {
-		pr_err("iomap failed for cpubiuctrl_block\n");
-		rc = -EINVAL;
-		goto cleanup;
-	}
-
-	rc = of_property_read_u32_index(np, name, CPU0_PWR_ZONE_CTRL_REG,
-					&cpu0_pwr_zone_ctrl_reg);
-	if (rc) {
-		pr_err("failed to read 1st entry from %s property (%d)\n", name,
-			rc);
-		rc = -EINVAL;
-		goto cleanup;
-	}
-
-	rc = of_property_read_u32_index(np, name, CPU_RESET_CONFIG_REG,
-					&cpu_rst_cfg_reg);
-	if (rc) {
-		pr_err("failed to read 2nd entry from %s property (%d)\n", name,
-			rc);
-		rc = -EINVAL;
-		goto cleanup;
-	}
-
-cleanup:
-	if (syscon_np)
-		of_node_put(syscon_np);
-
-	return rc;
-}
-
-static int __init setup_hifcont_regs(struct device_node *np)
-{
-	int rc = 0;
-	char *name;
-	struct device_node *syscon_np = NULL;
-
-	name = "syscon-cont";
-
-	syscon_np = of_parse_phandle(np, name, 0);
-	if (!syscon_np) {
-		pr_err("can't find phandle %s\n", name);
-		rc = -EINVAL;
-		goto cleanup;
-	}
-
-	hif_cont_block = of_iomap(syscon_np, 0);
-	if (!hif_cont_block) {
-		pr_err("iomap failed for hif_cont_block\n");
-		rc = -EINVAL;
-		goto cleanup;
-	}
-
-	/* offset is at top of hif_cont_block */
-	hif_cont_reg = 0;
-
-cleanup:
-	if (syscon_np)
-		of_node_put(syscon_np);
-
-	return rc;
-}
-
-static void __init brcmstb_cpu_ctrl_setup(unsigned int max_cpus)
-{
-	int rc;
-	struct device_node *np;
-	char *name;
-
-	name = "brcm,brcmstb-smpboot";
-	np = of_find_compatible_node(NULL, NULL, name);
-	if (!np) {
-		pr_err("can't find compatible node %s\n", name);
-		return;
-	}
-
-	rc = setup_hifcpubiuctrl_regs(np);
-	if (rc)
-		return;
-
-	rc = setup_hifcont_regs(np);
-	if (rc)
-		return;
-}
-
-static DEFINE_SPINLOCK(boot_lock);
-
-static void brcmstb_secondary_init(unsigned int cpu)
-{
-	/*
-	 * Synchronise with the boot thread.
-	 */
-	spin_lock(&boot_lock);
-	spin_unlock(&boot_lock);
-}
-
-static int brcmstb_boot_secondary(unsigned int cpu, struct task_struct *idle)
-{
-	/*
-	 * set synchronisation state between this boot processor
-	 * and the secondary one
-	 */
-	spin_lock(&boot_lock);
-
-	/* Bring up power to the core if necessary */
-	if (brcmstb_cpu_get_power_state(cpu) == 0)
-		brcmstb_cpu_power_on(cpu);
-
-	brcmstb_cpu_boot(cpu);
-
-	/*
-	 * now the secondary core is starting up let it run its
-	 * calibrations, then wait for it to finish
-	 */
-	spin_unlock(&boot_lock);
-
-	return 0;
-}
-
-static struct smp_operations brcmstb_smp_ops __initdata = {
-	.smp_prepare_cpus	= brcmstb_cpu_ctrl_setup,
-	.smp_secondary_init	= brcmstb_secondary_init,
-	.smp_boot_secondary	= brcmstb_boot_secondary,
-#ifdef CONFIG_HOTPLUG_CPU
-	.cpu_kill		= brcmstb_cpu_kill,
-	.cpu_die		= brcmstb_cpu_die,
-#endif
-};
-
-CPU_METHOD_OF_DECLARE(brcmstb_smp, "brcm,brahma-b15", &brcmstb_smp_ops);

arch/arm/mach-exynos/mcpm-exynos.c

@@ -43,7 +43,6 @@
 	"mcr	p15, 0, r0, c1, c0, 0	@ set SCTLR\n\t" \
 	"isb\n\t"\
 	"bl	v7_flush_dcache_"__stringify(level)"\n\t" \
-	"clrex\n\t"\
 	"mrc	p15, 0, r0, c1, c0, 1	@ get ACTLR\n\t" \
 	"bic	r0, r0, #(1 << 6)	@ disable local coherency\n\t" \
 	/* Dummy Load of a device register to avoid Erratum 799270 */ \

arch/arm/mach-imx/Kconfig

@@ -108,17 +108,6 @@ config SOC_IMX35
 if ARCH_MULTI_V4T
 
 comment "MX1 platforms:"
-config MACH_MXLADS
-	bool
-
-config ARCH_MX1ADS
-	bool "MX1ADS platform"
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select MACH_MXLADS
-	select SOC_IMX1
-	help
-	  Say Y here if you are using Motorola MX1ADS/MXLADS boards
 
 config MACH_SCB9328
 	bool "Synertronixx scb9328"
@@ -223,86 +212,6 @@ config MACH_MX27ADS
 	  Include support for MX27ADS platform. This includes specific
 	  configurations for the board and its peripherals.
 
-config MACH_PCM038
-	bool "Phytec phyCORE-i.MX27 CPU module (pcm038)"
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_MXC_W1
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX27
-	help
-	  Include support for phyCORE-i.MX27 (aka pcm038) platform. This
-	  includes specific configurations for the module and its peripherals.
-
-choice
-	prompt "Baseboard"
-	depends on MACH_PCM038
-	default MACH_PCM970_BASEBOARD
-
-config MACH_PCM970_BASEBOARD
-	bool "PHYTEC PCM970 development board"
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	help
-	  This adds board specific devices that can be found on Phytec's
-	  PCM970 evaluation board.
-
-endchoice
-
-config MACH_CPUIMX27
-	bool "Eukrea CPUIMX27 module"
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_MXC_W1
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX27
-	help
-	  Include support for Eukrea CPUIMX27 platform. This includes
-	  specific configurations for the module and its peripherals.
-
-config MACH_EUKREA_CPUIMX27_USESDHC2
-	bool "CPUIMX27 integrates SDHC2 module"
-	depends on MACH_CPUIMX27
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	help
-	  This adds support for the internal SDHC2 used on CPUIMX27
-	  for wifi or eMMC.
-
-config MACH_EUKREA_CPUIMX27_USEUART4
-	bool "CPUIMX27 integrates UART4 module"
-	depends on MACH_CPUIMX27
-	help
-	  This adds support for the internal UART4 used on CPUIMX27
-	  for bluetooth.
-
-choice
-	prompt "Baseboard"
-	depends on MACH_CPUIMX27
-	default MACH_EUKREA_MBIMX27_BASEBOARD
-
-config MACH_EUKREA_MBIMX27_BASEBOARD
-	bool "Eukrea MBIMX27 development board"
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_KEYPAD
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select LEDS_GPIO_REGISTER
-	help
-	  This adds board specific devices that can be found on Eukrea's
-	  MBIMX27 evaluation board.
-
-endchoice
-
 config MACH_MX27_3DS
 	bool "MX27PDK platform"
 	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
@@ -359,18 +268,6 @@ config MACH_PCA100
 	  Include support for phyCARD-s (aka pca100) platform. This
 	  includes specific configurations for the module and its peripherals.
 
-config MACH_MXT_TD60
-	bool "Maxtrack i-MXT TD60"
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select SOC_IMX27
-	help
-	  Include support for i-MXT (aka td60) platform. This
-	  includes specific configurations for the module and its peripherals.
-
 config MACH_IMX27_DT
 	bool "Support i.MX27 platforms from device tree"
 	select SOC_IMX27

arch/arm/mach-imx/Makefile

@@ -41,7 +41,6 @@ obj-y += ssi-fiq-ksym.o
 endif
 
 # i.MX1 based machines
-obj-$(CONFIG_ARCH_MX1ADS) += mach-mx1ads.o
 obj-$(CONFIG_MACH_SCB9328) += mach-scb9328.o
 obj-$(CONFIG_MACH_APF9328) += mach-apf9328.o
 
@@ -56,14 +55,9 @@ obj-$(CONFIG_MACH_IMX25_DT) += imx25-dt.o
 
 # i.MX27 based machines
 obj-$(CONFIG_MACH_MX27ADS) += mach-mx27ads.o
-obj-$(CONFIG_MACH_PCM038) += mach-pcm038.o
-obj-$(CONFIG_MACH_PCM970_BASEBOARD) += pcm970-baseboard.o
 obj-$(CONFIG_MACH_MX27_3DS) += mach-mx27_3ds.o
 obj-$(CONFIG_MACH_IMX27_VISSTRIM_M10) += mach-imx27_visstrim_m10.o
-obj-$(CONFIG_MACH_CPUIMX27) += mach-cpuimx27.o
-obj-$(CONFIG_MACH_EUKREA_MBIMX27_BASEBOARD) += eukrea_mbimx27-baseboard.o
 obj-$(CONFIG_MACH_PCA100) += mach-pca100.o
-obj-$(CONFIG_MACH_MXT_TD60) += mach-mxt_td60.o
 obj-$(CONFIG_MACH_IMX27_DT) += imx27-dt.o
 
 # i.MX31 based machines

arch/arm/mach-imx/board-pcm038.h

@@ -1,36 +0,0 @@
-/*
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_PCM038_H__
-#define __ASM_ARCH_MXC_BOARD_PCM038_H__
-
-#ifndef __ASSEMBLY__
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- * TODO: Add your own baseboard init function and call it from
- * inside pcm038_init().
- *
- * This example here is for the development board. Refer pcm970-baseboard.c
- */
-
-extern void pcm970_baseboard_init(void);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_PCM038_H__ */

arch/arm/mach-imx/common.h

@@ -98,11 +98,9 @@ void imx_set_cpu_arg(int cpu, u32 arg);
 void v7_secondary_startup(void);
 void imx_scu_map_io(void);
 void imx_smp_prepare(void);
-void imx_scu_standby_enable(void);
 #else
 static inline void imx_scu_map_io(void) {}
 static inline void imx_smp_prepare(void) {}
-static inline void imx_scu_standby_enable(void) {}
 #endif
 void imx_src_init(void);
 void imx_gpc_init(void);

arch/arm/mach-imx/cpuidle-imx6q.c

@@ -66,10 +66,6 @@ static struct cpuidle_driver imx6q_cpuidle_driver = {
 
 int __init imx6q_cpuidle_init(void)
 {
-	/* Need to enable SCU standby for entering WAIT modes */
-	if (!cpu_is_imx6sx())
-		imx_scu_standby_enable();
-
 	/* Set INT_MEM_CLK_LPM bit to get a reliable WAIT mode support */
 	imx6q_set_int_mem_clk_lpm(true);
 

arch/arm/mach-imx/eukrea-baseboards.h

@@ -27,23 +27,15 @@
  * This CPU module needs a baseboard to work. After basic initializing
  * its own devices, it calls baseboard's init function.
  * TODO: Add your own baseboard init function and call it from
- * inside eukrea_cpuimx25_init() eukrea_cpuimx27_init()
- * eukrea_cpuimx35_init() eukrea_cpuimx51_init()
- * or eukrea_cpuimx51sd_init().
+ * inside eukrea_cpuimx25_init() or eukrea_cpuimx35_init()
  *
  * This example here is for the development board. Refer
  * mach-mx25/eukrea_mbimxsd-baseboard.c for cpuimx25
- * mach-imx/eukrea_mbimx27-baseboard.c for cpuimx27
  * mach-mx3/eukrea_mbimxsd-baseboard.c for cpuimx35
- * mach-mx5/eukrea_mbimx51-baseboard.c for cpuimx51
- * mach-mx5/eukrea_mbimxsd-baseboard.c for cpuimx51sd
  */
 
 extern void eukrea_mbimxsd25_baseboard_init(void);
-extern void eukrea_mbimx27_baseboard_init(void);
 extern void eukrea_mbimxsd35_baseboard_init(void);
-extern void eukrea_mbimx51_baseboard_init(void);
-extern void eukrea_mbimxsd51_baseboard_init(void);
 
 #endif
 

arch/arm/mach-imx/eukrea_mbimx27-baseboard.c

@@ -1,351 +0,0 @@
-/*
- * Copyright (C) 2009-2010 Eric Benard - eric@eukrea.com
- *
- * Based on pcm970-baseboard.c which is :
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/irq.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/backlight.h>
-#include <video/platform_lcd.h>
-
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-
-static const int eukrea_mbimx27_pins[] __initconst = {
-	/* UART2 */
-	PE3_PF_UART2_CTS,
-	PE4_PF_UART2_RTS,
-	PE6_PF_UART2_TXD,
-	PE7_PF_UART2_RXD,
-	/* UART3 */
-	PE8_PF_UART3_TXD,
-	PE9_PF_UART3_RXD,
-	PE10_PF_UART3_CTS,
-	PE11_PF_UART3_RTS,
-	/* UART4 */
-#if !defined(CONFIG_MACH_EUKREA_CPUIMX27_USEUART4)
-	PB26_AF_UART4_RTS,
-	PB28_AF_UART4_TXD,
-	PB29_AF_UART4_CTS,
-	PB31_AF_UART4_RXD,
-#endif
-	/* SDHC1*/
-	PE18_PF_SD1_D0,
-	PE19_PF_SD1_D1,
-	PE20_PF_SD1_D2,
-	PE21_PF_SD1_D3,
-	PE22_PF_SD1_CMD,
-	PE23_PF_SD1_CLK,
-	/* display */
-	PA5_PF_LSCLK,
-	PA6_PF_LD0,
-	PA7_PF_LD1,
-	PA8_PF_LD2,
-	PA9_PF_LD3,
-	PA10_PF_LD4,
-	PA11_PF_LD5,
-	PA12_PF_LD6,
-	PA13_PF_LD7,
-	PA14_PF_LD8,
-	PA15_PF_LD9,
-	PA16_PF_LD10,
-	PA17_PF_LD11,
-	PA18_PF_LD12,
-	PA19_PF_LD13,
-	PA20_PF_LD14,
-	PA21_PF_LD15,
-	PA22_PF_LD16,
-	PA23_PF_LD17,
-	PA28_PF_HSYNC,
-	PA29_PF_VSYNC,
-	PA30_PF_CONTRAST,
-	PA31_PF_OE_ACD,
-	/* SPI1 */
-	PD29_PF_CSPI1_SCLK,
-	PD30_PF_CSPI1_MISO,
-	PD31_PF_CSPI1_MOSI,
-	/* SSI4 */
-#if defined(CONFIG_SND_SOC_EUKREA_TLV320) \
-	|| defined(CONFIG_SND_SOC_EUKREA_TLV320_MODULE)
-	PC16_PF_SSI4_FS,
-	PC17_PF_SSI4_RXD | GPIO_PUEN,
-	PC18_PF_SSI4_TXD | GPIO_PUEN,
-	PC19_PF_SSI4_CLK,
-#endif
-};
-
-static const uint32_t eukrea_mbimx27_keymap[] = {
-	KEY(0, 0, KEY_UP),
-	KEY(0, 1, KEY_DOWN),
-	KEY(1, 0, KEY_RIGHT),
-	KEY(1, 1, KEY_LEFT),
-};
-
-static const struct matrix_keymap_data
-eukrea_mbimx27_keymap_data __initconst = {
-	.keymap         = eukrea_mbimx27_keymap,
-	.keymap_size    = ARRAY_SIZE(eukrea_mbimx27_keymap),
-};
-
-static const struct gpio_led eukrea_mbimx27_gpio_leds[] __initconst = {
-	{
-		.name			= "led1",
-		.default_trigger	= "heartbeat",
-		.active_low		= 1,
-		.gpio			= GPIO_PORTF | 16,
-	},
-	{
-		.name			= "led2",
-		.default_trigger	= "none",
-		.active_low		= 1,
-		.gpio			= GPIO_PORTF | 19,
-	},
-};
-
-static const struct gpio_led_platform_data
-		eukrea_mbimx27_gpio_led_info __initconst = {
-	.leds		= eukrea_mbimx27_gpio_leds,
-	.num_leds	= ARRAY_SIZE(eukrea_mbimx27_gpio_leds),
-};
-
-static struct imx_fb_videomode eukrea_mbimx27_modes[] = {
-	{
-		.mode = {
-			.name		= "CMO-QVGA",
-			.refresh	= 60,
-			.xres		= 320,
-			.yres		= 240,
-			.pixclock	= 156000,
-			.hsync_len	= 30,
-			.left_margin	= 38,
-			.right_margin	= 20,
-			.vsync_len	= 3,
-			.upper_margin	= 15,
-			.lower_margin	= 4,
-		},
-		.pcr		= 0xFAD08B80,
-		.bpp		= 16,
-	}, {
-		.mode = {
-			.name		= "DVI-VGA",
-			.refresh	= 60,
-			.xres		= 640,
-			.yres		= 480,
-			.pixclock	= 32000,
-			.hsync_len	= 1,
-			.left_margin	= 35,
-			.right_margin	= 0,
-			.vsync_len	= 1,
-			.upper_margin	= 7,
-			.lower_margin	= 0,
-		},
-		.pcr		= 0xFA208B80,
-		.bpp		= 16,
-	}, {
-		.mode = {
-			.name		= "DVI-SVGA",
-			.refresh	= 60,
-			.xres		= 800,
-			.yres		= 600,
-			.pixclock	= 25000,
-			.hsync_len	= 1,
-			.left_margin	= 35,
-			.right_margin	= 0,
-			.vsync_len	= 1,
-			.upper_margin	= 7,
-			.lower_margin	= 0,
-		},
-		.pcr		= 0xFA208B80,
-		.bpp		= 16,
-	},
-};
-
-static const struct imx_fb_platform_data eukrea_mbimx27_fb_data __initconst = {
-	.mode = eukrea_mbimx27_modes,
-	.num_modes = ARRAY_SIZE(eukrea_mbimx27_modes),
-
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00040060,
-};
-
-static void eukrea_mbimx27_bl_set_intensity(int intensity)
-{
-	if (intensity)
-		gpio_direction_output(GPIO_PORTE | 5, 1);
-	else
-		gpio_direction_output(GPIO_PORTE | 5, 0);
-}
-
-static struct generic_bl_info eukrea_mbimx27_bl_info = {
-	.name			= "eukrea_mbimx27-bl",
-	.max_intensity		= 0xff,
-	.default_intensity	= 0xff,
-	.set_bl_intensity	= eukrea_mbimx27_bl_set_intensity,
-};
-
-static struct platform_device eukrea_mbimx27_bl_dev = {
-	.name			= "generic-bl",
-	.id			= 1,
-	.dev = {
-		.platform_data	= &eukrea_mbimx27_bl_info,
-	},
-};
-
-static void eukrea_mbimx27_lcd_power_set(struct plat_lcd_data *pd,
-				   unsigned int power)
-{
-	if (power)
-		gpio_direction_output(GPIO_PORTA | 25, 1);
-	else
-		gpio_direction_output(GPIO_PORTA | 25, 0);
-}
-
-static struct plat_lcd_data eukrea_mbimx27_lcd_power_data = {
-	.set_power		= eukrea_mbimx27_lcd_power_set,
-};
-
-static struct platform_device eukrea_mbimx27_lcd_powerdev = {
-	.name			= "platform-lcd",
-	.dev.platform_data	= &eukrea_mbimx27_lcd_power_data,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-#define ADS7846_PENDOWN (GPIO_PORTD | 25)
-
-static void __maybe_unused ads7846_dev_init(void)
-{
-	if (gpio_request(ADS7846_PENDOWN, "ADS7846 pendown") < 0) {
-		printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
-		return;
-	}
-	gpio_direction_input(ADS7846_PENDOWN);
-}
-
-static int ads7846_get_pendown_state(void)
-{
-	return !gpio_get_value(ADS7846_PENDOWN);
-}
-
-static struct ads7846_platform_data ads7846_config __initdata = {
-	.get_pendown_state	= ads7846_get_pendown_state,
-	.keep_vref_on		= 1,
-};
-
-static struct spi_board_info __maybe_unused
-		eukrea_mbimx27_spi_board_info[] __initdata = {
-	[0] = {
-		.modalias	= "ads7846",
-		.bus_num	= 0,
-		.chip_select	= 0,
-		.max_speed_hz	= 1500000,
-		/* irq number is run-time assigned */
-		.platform_data	= &ads7846_config,
-		.mode           = SPI_MODE_2,
-	},
-};
-
-static int eukrea_mbimx27_spi_cs[] = {GPIO_PORTD | 28};
-
-static const struct spi_imx_master eukrea_mbimx27_spi0_data __initconst = {
-	.chipselect	= eukrea_mbimx27_spi_cs,
-	.num_chipselect = ARRAY_SIZE(eukrea_mbimx27_spi_cs),
-};
-
-static struct i2c_board_info eukrea_mbimx27_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("tlv320aic23", 0x1a),
-	},
-};
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
-	.dat3_card_detect = 1,
-};
-
-static const
-struct imx_ssi_platform_data eukrea_mbimx27_ssi_pdata __initconst = {
-	.flags = IMX_SSI_DMA | IMX_SSI_USE_I2S_SLAVE,
-};
-
-/*
- * system init for baseboard usage. Will be called by cpuimx27 init.
- *
- * Add platform devices present on this baseboard and init
- * them from CPU side as far as required to use them later on
- */
-void __init eukrea_mbimx27_baseboard_init(void)
-{
-	mxc_gpio_setup_multiple_pins(eukrea_mbimx27_pins,
-		ARRAY_SIZE(eukrea_mbimx27_pins), "MBIMX27");
-
-	imx27_add_imx_uart1(&uart_pdata);
-	imx27_add_imx_uart2(&uart_pdata);
-#if !defined(CONFIG_MACH_EUKREA_CPUIMX27_USEUART4)
-	imx27_add_imx_uart3(&uart_pdata);
-#endif
-
-	imx27_add_imx_fb(&eukrea_mbimx27_fb_data);
-	imx27_add_mxc_mmc(0, &sdhc_pdata);
-
-	i2c_register_board_info(0, eukrea_mbimx27_i2c_devices,
-				ARRAY_SIZE(eukrea_mbimx27_i2c_devices));
-
-	imx27_add_imx_ssi(0, &eukrea_mbimx27_ssi_pdata);
-
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) \
-	|| defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-	/* ADS7846 Touchscreen controller init */
-	mxc_gpio_mode(GPIO_PORTD | 25 | GPIO_GPIO | GPIO_IN);
-	ads7846_dev_init();
-#endif
-
-	/* SPI_CS0 init */
-	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
-	imx27_add_spi_imx0(&eukrea_mbimx27_spi0_data);
-	eukrea_mbimx27_spi_board_info[0].irq = gpio_to_irq(IMX_GPIO_NR(4, 25));
-	spi_register_board_info(eukrea_mbimx27_spi_board_info,
-			ARRAY_SIZE(eukrea_mbimx27_spi_board_info));
-
-	/* Leds configuration */
-	mxc_gpio_mode(GPIO_PORTF | 16 | GPIO_GPIO | GPIO_OUT);
-	mxc_gpio_mode(GPIO_PORTF | 19 | GPIO_GPIO | GPIO_OUT);
-	/* Backlight */
-	mxc_gpio_mode(GPIO_PORTE | 5 | GPIO_GPIO | GPIO_OUT);
-	gpio_request(GPIO_PORTE | 5, "backlight");
-	platform_device_register(&eukrea_mbimx27_bl_dev);
-	/* LCD Reset */
-	mxc_gpio_mode(GPIO_PORTA | 25 | GPIO_GPIO | GPIO_OUT);
-	gpio_request(GPIO_PORTA | 25, "lcd_enable");
-	platform_device_register(&eukrea_mbimx27_lcd_powerdev);
-
-	imx27_add_imx_keypad(&eukrea_mbimx27_keymap_data);
-
-	gpio_led_register_device(-1, &eukrea_mbimx27_gpio_led_info);
-	imx_add_platform_device("eukrea_tlv320", 0, NULL, 0, NULL, 0);
-}

arch/arm/mach-imx/iomux-imx31.c

@@ -64,7 +64,6 @@ int mxc_iomux_mode(unsigned int pin_mode)
 
 	return ret;
 }
-EXPORT_SYMBOL(mxc_iomux_mode);
 
 /*
  * This function configures the pad value for a IOMUX pin.
@@ -90,7 +89,6 @@ void mxc_iomux_set_pad(enum iomux_pins pin, u32 config)
 
 	spin_unlock(&gpio_mux_lock);
 }
-EXPORT_SYMBOL(mxc_iomux_set_pad);
 
 /*
  * allocs a single pin:
@@ -116,7 +114,6 @@ int mxc_iomux_alloc_pin(unsigned int pin, const char *label)
 
 	return 0;
 }
-EXPORT_SYMBOL(mxc_iomux_alloc_pin);
 
 int mxc_iomux_setup_multiple_pins(const unsigned int *pin_list, unsigned count,
 		const char *label)
@@ -137,7 +134,6 @@ setup_error:
 	mxc_iomux_release_multiple_pins(pin_list, i);
 	return ret;
 }
-EXPORT_SYMBOL(mxc_iomux_setup_multiple_pins);
 
 void mxc_iomux_release_pin(unsigned int pin)
 {
@@ -146,7 +142,6 @@ void mxc_iomux_release_pin(unsigned int pin)
 	if (pad < (PIN_MAX + 1))
 		clear_bit(pad, mxc_pin_alloc_map);
 }
-EXPORT_SYMBOL(mxc_iomux_release_pin);
 
 void mxc_iomux_release_multiple_pins(const unsigned int *pin_list, int count)
 {
@@ -158,7 +153,6 @@ void mxc_iomux_release_multiple_pins(const unsigned int *pin_list, int count)
 		p++;
 	}
 }
-EXPORT_SYMBOL(mxc_iomux_release_multiple_pins);
 
 /*
  * This function enables/disables the general purpose function for a particular
@@ -178,4 +172,3 @@ void mxc_iomux_set_gpr(enum iomux_gp_func gp, bool en)
 	__raw_writel(l, IOMUXGPR);
 	spin_unlock(&gpio_mux_lock);
 }
-EXPORT_SYMBOL(mxc_iomux_set_gpr);

arch/arm/mach-imx/iomux-v1.c

@@ -153,7 +153,6 @@ int mxc_gpio_mode(int gpio_mode)
 
 	return 0;
 }
-EXPORT_SYMBOL(mxc_gpio_mode);
 
 static int imx_iomuxv1_setup_multiple(const int *list, unsigned count)
 {
@@ -178,7 +177,6 @@ int mxc_gpio_setup_multiple_pins(const int *pin_list, unsigned count,
 	ret = imx_iomuxv1_setup_multiple(pin_list, count);
 	return ret;
 }
-EXPORT_SYMBOL(mxc_gpio_setup_multiple_pins);
 
 int __init imx_iomuxv1_init(void __iomem *base, int numports)
 {

arch/arm/mach-imx/iomux-v3.c

@@ -55,7 +55,6 @@ int mxc_iomux_v3_setup_pad(iomux_v3_cfg_t pad)
 
 	return 0;
 }
-EXPORT_SYMBOL(mxc_iomux_v3_setup_pad);
 
 int mxc_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t *pad_list, unsigned count)
 {
@@ -71,7 +70,6 @@ int mxc_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t *pad_list, unsigned count)
 	}
 	return 0;
 }
-EXPORT_SYMBOL(mxc_iomux_v3_setup_multiple_pads);
 
 void mxc_iomux_v3_init(void __iomem *iomux_v3_base)
 {

arch/arm/mach-imx/mach-cpuimx27.c

@@ -1,321 +0,0 @@
-/*
- * Copyright (C) 2009 Eric Benard - eric@eukrea.com
- *
- * Based on pcm038.c which is :
- * Copyright 2007 Robert Schwebel <r.schwebel@pengutronix.de>, Pengutronix
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/i2c.h>
-#include <linux/io.h>
-#include <linux/mtd/plat-ram.h>
-#include <linux/mtd/physmap.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "eukrea-baseboards.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-#include "ulpi.h"
-
-static const int eukrea_cpuimx27_pins[] __initconst = {
-	/* UART1 */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-	/* UART4 */
-#if defined(CONFIG_MACH_EUKREA_CPUIMX27_USEUART4)
-	PB26_AF_UART4_RTS,
-	PB28_AF_UART4_TXD,
-	PB29_AF_UART4_CTS,
-	PB31_AF_UART4_RXD,
-#endif
-	/* FEC */
-	PD0_AIN_FEC_TXD0,
-	PD1_AIN_FEC_TXD1,
-	PD2_AIN_FEC_TXD2,
-	PD3_AIN_FEC_TXD3,
-	PD4_AOUT_FEC_RX_ER,
-	PD5_AOUT_FEC_RXD1,
-	PD6_AOUT_FEC_RXD2,
-	PD7_AOUT_FEC_RXD3,
-	PD8_AF_FEC_MDIO,
-	PD9_AIN_FEC_MDC,
-	PD10_AOUT_FEC_CRS,
-	PD11_AOUT_FEC_TX_CLK,
-	PD12_AOUT_FEC_RXD0,
-	PD13_AOUT_FEC_RX_DV,
-	PD14_AOUT_FEC_RX_CLK,
-	PD15_AOUT_FEC_COL,
-	PD16_AIN_FEC_TX_ER,
-	PF23_AIN_FEC_TX_EN,
-	/* I2C1 */
-	PD17_PF_I2C_DATA,
-	PD18_PF_I2C_CLK,
-	/* SDHC2 */
-#if defined(CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2)
-	PB4_PF_SD2_D0,
-	PB5_PF_SD2_D1,
-	PB6_PF_SD2_D2,
-	PB7_PF_SD2_D3,
-	PB8_PF_SD2_CMD,
-	PB9_PF_SD2_CLK,
-#endif
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
-	/* Quad UART's IRQ */
-	GPIO_PORTB | 22 | GPIO_GPIO | GPIO_IN,
-	GPIO_PORTB | 23 | GPIO_GPIO | GPIO_IN,
-	GPIO_PORTB | 27 | GPIO_GPIO | GPIO_IN,
-	GPIO_PORTB | 30 | GPIO_GPIO | GPIO_IN,
-#endif
-	/* OTG */
-	PC7_PF_USBOTG_DATA5,
-	PC8_PF_USBOTG_DATA6,
-	PC9_PF_USBOTG_DATA0,
-	PC10_PF_USBOTG_DATA2,
-	PC11_PF_USBOTG_DATA1,
-	PC12_PF_USBOTG_DATA4,
-	PC13_PF_USBOTG_DATA3,
-	PE0_PF_USBOTG_NXT,
-	PE1_PF_USBOTG_STP,
-	PE2_PF_USBOTG_DIR,
-	PE24_PF_USBOTG_CLK,
-	PE25_PF_USBOTG_DATA7,
-	/* USBH2 */
-	PA0_PF_USBH2_CLK,
-	PA1_PF_USBH2_DIR,
-	PA2_PF_USBH2_DATA7,
-	PA3_PF_USBH2_NXT,
-	PA4_PF_USBH2_STP,
-	PD19_AF_USBH2_DATA4,
-	PD20_AF_USBH2_DATA3,
-	PD21_AF_USBH2_DATA6,
-	PD22_AF_USBH2_DATA0,
-	PD23_AF_USBH2_DATA2,
-	PD24_AF_USBH2_DATA1,
-	PD26_AF_USBH2_DATA5,
-};
-
-static struct physmap_flash_data eukrea_cpuimx27_flash_data = {
-	.width = 2,
-};
-
-static struct resource eukrea_cpuimx27_flash_resource = {
-	.start = 0xc0000000,
-	.end   = 0xc3ffffff,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device eukrea_cpuimx27_nor_mtd_device = {
-	.name = "physmap-flash",
-	.id = 0,
-	.dev = {
-		.platform_data = &eukrea_cpuimx27_flash_data,
-	},
-	.num_resources = 1,
-	.resource = &eukrea_cpuimx27_flash_resource,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct mxc_nand_platform_data
-cpuimx27_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
-	&eukrea_cpuimx27_nor_mtd_device,
-};
-
-static const struct imxi2c_platform_data cpuimx27_i2c1_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct i2c_board_info eukrea_cpuimx27_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("pcf8563", 0x51),
-	},
-};
-
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
-static struct plat_serial8250_port serial_platform_data[] = {
-	{
-		.mapbase = (unsigned long)(MX27_CS3_BASE_ADDR + 0x200000),
-		/* irq number is run-time assigned */
-		.uartclk = 14745600,
-		.regshift = 1,
-		.iotype = UPIO_MEM,
-		.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
-	}, {
-		.mapbase = (unsigned long)(MX27_CS3_BASE_ADDR + 0x400000),
-		/* irq number is run-time assigned */
-		.uartclk = 14745600,
-		.regshift = 1,
-		.iotype = UPIO_MEM,
-		.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
-	}, {
-		.mapbase = (unsigned long)(MX27_CS3_BASE_ADDR + 0x800000),
-		/* irq number is run-time assigned */
-		.uartclk = 14745600,
-		.regshift = 1,
-		.iotype = UPIO_MEM,
-		.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
-	}, {
-		.mapbase = (unsigned long)(MX27_CS3_BASE_ADDR + 0x1000000),
-		/* irq number is run-time assigned */
-		.uartclk = 14745600,
-		.regshift = 1,
-		.iotype = UPIO_MEM,
-		.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
-	}, {
-	}
-};
-
-static struct platform_device serial_device = {
-	.name = "serial8250",
-	.id = 0,
-	.dev = {
-		.platform_data = serial_platform_data,
-	},
-};
-#endif
-
-static int eukrea_cpuimx27_otg_init(struct platform_device *pdev)
-{
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
-	.init	= eukrea_cpuimx27_otg_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static int eukrea_cpuimx27_usbh2_init(struct platform_device *pdev)
-{
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
-	.init	= eukrea_cpuimx27_usbh2_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
-	.operating_mode = FSL_USB2_DR_DEVICE,
-	.phy_mode       = FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init eukrea_cpuimx27_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = true;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = false;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 1;
-}
-__setup("otg_mode=", eukrea_cpuimx27_otg_mode);
-
-static void __init eukrea_cpuimx27_init(void)
-{
-	imx27_soc_init();
-
-	mxc_gpio_setup_multiple_pins(eukrea_cpuimx27_pins,
-		ARRAY_SIZE(eukrea_cpuimx27_pins), "CPUIMX27");
-
-	imx27_add_imx_uart0(&uart_pdata);
-
-	imx27_add_mxc_nand(&cpuimx27_nand_board_info);
-
-	i2c_register_board_info(0, eukrea_cpuimx27_i2c_devices,
-				ARRAY_SIZE(eukrea_cpuimx27_i2c_devices));
-
-	imx27_add_imx_i2c(0, &cpuimx27_i2c1_data);
-
-	imx27_add_fec(NULL);
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-	imx27_add_imx2_wdt();
-	imx27_add_mxc_w1();
-
-#if defined(CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2)
-	/* SDHC2 can be used for Wifi */
-	imx27_add_mxc_mmc(1, NULL);
-#endif
-#if defined(CONFIG_MACH_EUKREA_CPUIMX27_USEUART4)
-	/* in which case UART4 is also used for Bluetooth */
-	imx27_add_imx_uart3(&uart_pdata);
-#endif
-
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
-	serial_platform_data[0].irq = IMX_GPIO_NR(2, 23);
-	serial_platform_data[1].irq = IMX_GPIO_NR(2, 22);
-	serial_platform_data[2].irq = IMX_GPIO_NR(2, 27);
-	serial_platform_data[3].irq = IMX_GPIO_NR(2, 30);
-	platform_device_register(&serial_device);
-#endif
-
-	if (otg_mode_host) {
-		otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-				ULPI_OTG_DRVVBUS_EXT);
-		if (otg_pdata.otg)
-			imx27_add_mxc_ehci_otg(&otg_pdata);
-	} else {
-		imx27_add_fsl_usb2_udc(&otg_device_pdata);
-	}
-
-	usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT);
-	if (usbh2_pdata.otg)
-		imx27_add_mxc_ehci_hs(2, &usbh2_pdata);
-
-#ifdef CONFIG_MACH_EUKREA_MBIMX27_BASEBOARD
-	eukrea_mbimx27_baseboard_init();
-#endif
-}
-
-static void __init eukrea_cpuimx27_timer_init(void)
-{
-	mx27_clocks_init(26000000);
-}
-
-MACHINE_START(EUKREA_CPUIMX27, "EUKREA CPUIMX27")
-	.atag_offset = 0x100,
-	.map_io = mx27_map_io,
-	.init_early = imx27_init_early,
-	.init_irq = mx27_init_irq,
-	.init_time	= eukrea_cpuimx27_timer_init,
-	.init_machine = eukrea_cpuimx27_init,
-	.restart	= mxc_restart,
-MACHINE_END

arch/arm/mach-imx/mach-mx1ads.c

@@ -1,154 +0,0 @@
-/*
- * arch/arm/mach-imx/mach-mx1ads.c
- *
- * Initially based on:
- *	linux-2.6.7-imx/arch/arm/mach-imx/scb9328.c
- *	Copyright (c) 2004 Sascha Hauer <sascha@saschahauer.de>
- *
- * 2004 (c) MontaVista Software, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/i2c.h>
-#include <linux/i2c/pcf857x.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "common.h"
-#include "devices-imx1.h"
-#include "hardware.h"
-#include "iomux-mx1.h"
-
-static const int mx1ads_pins[] __initconst = {
-	/* UART1 */
-	PC9_PF_UART1_CTS,
-	PC10_PF_UART1_RTS,
-	PC11_PF_UART1_TXD,
-	PC12_PF_UART1_RXD,
-	/* UART2 */
-	PB28_PF_UART2_CTS,
-	PB29_PF_UART2_RTS,
-	PB30_PF_UART2_TXD,
-	PB31_PF_UART2_RXD,
-	/* I2C */
-	PA15_PF_I2C_SDA,
-	PA16_PF_I2C_SCL,
-	/* SPI */
-	PC13_PF_SPI1_SPI_RDY,
-	PC14_PF_SPI1_SCLK,
-	PC15_PF_SPI1_SS,
-	PC16_PF_SPI1_MISO,
-	PC17_PF_SPI1_MOSI,
-};
-
-/*
- * UARTs platform data
- */
-
-static const struct imxuart_platform_data uart0_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-       
-static const struct imxuart_platform_data uart1_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-/*
- * Physmap flash
- */
-
-static const struct physmap_flash_data mx1ads_flash_data __initconst = {
-	.width		= 4,		/* bankwidth in bytes */
-};
-
-static const struct resource flash_resource __initconst = {
-	.start	= MX1_CS0_PHYS,
-	.end	= MX1_CS0_PHYS + SZ_32M - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-/*
- * I2C
- */
-static struct pcf857x_platform_data pcf857x_data[] = {
-	{
-		.gpio_base = 4 * 32,
-	}, {
-		.gpio_base = 4 * 32 + 16,
-	}
-};
-
-static const struct imxi2c_platform_data mx1ads_i2c_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct i2c_board_info mx1ads_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("pcf8575", 0x22),
-		.platform_data = &pcf857x_data[0],
-	}, {
-		I2C_BOARD_INFO("pcf8575", 0x24),
-		.platform_data = &pcf857x_data[1],
-	},
-};
-
-/*
- * Board init
- */
-static void __init mx1ads_init(void)
-{
-	imx1_soc_init();
-
-	mxc_gpio_setup_multiple_pins(mx1ads_pins,
-		ARRAY_SIZE(mx1ads_pins), "mx1ads");
-
-	/* UART */
-	imx1_add_imx_uart0(&uart0_pdata);
-	imx1_add_imx_uart1(&uart1_pdata);
-
-	/* Physmap flash */
-	platform_device_register_resndata(NULL, "physmap-flash", 0,
-			&flash_resource, 1,
-			&mx1ads_flash_data, sizeof(mx1ads_flash_data));
-
-	/* I2C */
-	i2c_register_board_info(0, mx1ads_i2c_devices,
-				ARRAY_SIZE(mx1ads_i2c_devices));
-
-	imx1_add_imx_i2c(&mx1ads_i2c_data);
-}
-
-static void __init mx1ads_timer_init(void)
-{
-	mx1_clocks_init(32000);
-}
-
-MACHINE_START(MX1ADS, "Freescale MX1ADS")
-	/* Maintainer: Sascha Hauer, Pengutronix */
-	.atag_offset = 0x100,
-	.map_io = mx1_map_io,
-	.init_early = imx1_init_early,
-	.init_irq = mx1_init_irq,
-	.init_time	= mx1ads_timer_init,
-	.init_machine = mx1ads_init,
-	.restart	= mxc_restart,
-MACHINE_END
-
-MACHINE_START(MXLADS, "Freescale MXLADS")
-	.atag_offset = 0x100,
-	.map_io = mx1_map_io,
-	.init_early = imx1_init_early,
-	.init_irq = mx1_init_irq,
-	.init_time	= mx1ads_timer_init,
-	.init_machine = mx1ads_init,
-	.restart	= mxc_restart,
-MACHINE_END

arch/arm/mach-imx/mach-mxt_td60.c

@@ -1,273 +0,0 @@
-/*
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
- *  Copyright 2006-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/i2c.h>
-#include <linux/irq.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-#include <linux/gpio.h>
-#include <linux/platform_data/pca953x.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-
-static const int mxt_td60_pins[] __initconst = {
-	/* UART0 */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-	/* UART1 */
-	PE3_PF_UART2_CTS,
-	PE4_PF_UART2_RTS,
-	PE6_PF_UART2_TXD,
-	PE7_PF_UART2_RXD,
-	/* UART2 */
-	PE8_PF_UART3_TXD,
-	PE9_PF_UART3_RXD,
-	PE10_PF_UART3_CTS,
-	PE11_PF_UART3_RTS,
-	/* FEC */
-	PD0_AIN_FEC_TXD0,
-	PD1_AIN_FEC_TXD1,
-	PD2_AIN_FEC_TXD2,
-	PD3_AIN_FEC_TXD3,
-	PD4_AOUT_FEC_RX_ER,
-	PD5_AOUT_FEC_RXD1,
-	PD6_AOUT_FEC_RXD2,
-	PD7_AOUT_FEC_RXD3,
-	PD8_AF_FEC_MDIO,
-	PD9_AIN_FEC_MDC,
-	PD10_AOUT_FEC_CRS,
-	PD11_AOUT_FEC_TX_CLK,
-	PD12_AOUT_FEC_RXD0,
-	PD13_AOUT_FEC_RX_DV,
-	PD14_AOUT_FEC_RX_CLK,
-	PD15_AOUT_FEC_COL,
-	PD16_AIN_FEC_TX_ER,
-	PF23_AIN_FEC_TX_EN,
-	/* I2C1 */
-	PD17_PF_I2C_DATA,
-	PD18_PF_I2C_CLK,
-	/* I2C2 */
-	PC5_PF_I2C2_SDA,
-	PC6_PF_I2C2_SCL,
-	/* FB */
-	PA5_PF_LSCLK,
-	PA6_PF_LD0,
-	PA7_PF_LD1,
-	PA8_PF_LD2,
-	PA9_PF_LD3,
-	PA10_PF_LD4,
-	PA11_PF_LD5,
-	PA12_PF_LD6,
-	PA13_PF_LD7,
-	PA14_PF_LD8,
-	PA15_PF_LD9,
-	PA16_PF_LD10,
-	PA17_PF_LD11,
-	PA18_PF_LD12,
-	PA19_PF_LD13,
-	PA20_PF_LD14,
-	PA21_PF_LD15,
-	PA22_PF_LD16,
-	PA23_PF_LD17,
-	PA25_PF_CLS,
-	PA27_PF_SPL_SPR,
-	PA28_PF_HSYNC,
-	PA29_PF_VSYNC,
-	PA30_PF_CONTRAST,
-	PA31_PF_OE_ACD,
-	/* OWIRE */
-	PE16_AF_OWIRE,
-	/* SDHC1*/
-	PE18_PF_SD1_D0,
-	PE19_PF_SD1_D1,
-	PE20_PF_SD1_D2,
-	PE21_PF_SD1_D3,
-	PE22_PF_SD1_CMD,
-	PE23_PF_SD1_CLK,
-	PF8_AF_ATA_IORDY,
-	/* SDHC2*/
-	PB4_PF_SD2_D0,
-	PB5_PF_SD2_D1,
-	PB6_PF_SD2_D2,
-	PB7_PF_SD2_D3,
-	PB8_PF_SD2_CMD,
-	PB9_PF_SD2_CLK,
-};
-
-static const struct mxc_nand_platform_data
-mxt_td60_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static const struct imxi2c_platform_data mxt_td60_i2c0_data __initconst = {
-	.bitrate = 100000,
-};
-
-/* PCA9557 */
-static int mxt_td60_pca9557_setup(struct i2c_client *client,
-				unsigned gpio_base, unsigned ngpio,
-				void *context)
-{
-	static int mxt_td60_gpio_value[] = {
-		-1, -1, -1, -1, -1, -1, -1, 1
-	};
-	int n;
-
-	for (n = 0; n < ARRAY_SIZE(mxt_td60_gpio_value); ++n) {
-		gpio_request(gpio_base + n, "MXT_TD60 GPIO Exp");
-		if (mxt_td60_gpio_value[n] < 0)
-			gpio_direction_input(gpio_base + n);
-		else
-			gpio_direction_output(gpio_base + n,
-						mxt_td60_gpio_value[n]);
-		gpio_export(gpio_base + n, 0);
-	}
-
-	return 0;
-}
-
-static struct pca953x_platform_data mxt_td60_pca9557_pdata = {
-	.gpio_base	= 240, /* place PCA9557 after all MX27 gpio pins */
-	.invert		= 0, /* Do not invert */
-	.setup		= mxt_td60_pca9557_setup,
-};
-
-static struct i2c_board_info mxt_td60_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("pca9557", 0x18),
-		.platform_data = &mxt_td60_pca9557_pdata,
-	},
-};
-
-static const struct imxi2c_platform_data mxt_td60_i2c1_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct i2c_board_info mxt_td60_i2c2_devices[] = {
-};
-
-static struct imx_fb_videomode mxt_td60_modes[] = {
-	{
-		.mode = {
-			.name		= "Chimei LW700AT9003",
-			.refresh	= 60,
-			.xres		= 800,
-			.yres		= 480,
-			.pixclock	= 30303,
-			.hsync_len	= 64,
-			.left_margin	= 0x67,
-			.right_margin	= 0x68,
-			.vsync_len	= 16,
-			.upper_margin	= 0x0f,
-			.lower_margin	= 0x0f,
-		},
-		.bpp		= 16,
-		.pcr		= 0xFA208B83,
-	},
-};
-
-static const struct imx_fb_platform_data mxt_td60_fb_data __initconst = {
-	.mode = mxt_td60_modes,
-	.num_modes = ARRAY_SIZE(mxt_td60_modes),
-
-	/*
-	 * - HSYNC active high
-	 * - VSYNC active high
-	 * - clk notenabled while idle
-	 * - clock inverted
-	 * - data not inverted
-	 * - data enable low active
-	 * - enable sharp mode
-	 */
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00020010,
-};
-
-static int mxt_td60_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
-				void *data)
-{
-	return request_irq(gpio_to_irq(IMX_GPIO_NR(6, 8)), detect_irq,
-			   IRQF_TRIGGER_FALLING, "sdhc1-card-detect", data);
-}
-
-static void mxt_td60_sdhc1_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(IMX_GPIO_NR(6, 8)), data);
-}
-
-static const struct imxmmc_platform_data sdhc1_pdata __initconst = {
-	.init = mxt_td60_sdhc1_init,
-	.exit = mxt_td60_sdhc1_exit,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static void __init mxt_td60_board_init(void)
-{
-	imx27_soc_init();
-
-	mxc_gpio_setup_multiple_pins(mxt_td60_pins, ARRAY_SIZE(mxt_td60_pins),
-			"MXT_TD60");
-
-	imx27_add_imx_uart0(&uart_pdata);
-	imx27_add_imx_uart1(&uart_pdata);
-	imx27_add_imx_uart2(&uart_pdata);
-	imx27_add_mxc_nand(&mxt_td60_nand_board_info);
-
-	i2c_register_board_info(0, mxt_td60_i2c_devices,
-				ARRAY_SIZE(mxt_td60_i2c_devices));
-
-	i2c_register_board_info(1, mxt_td60_i2c2_devices,
-				ARRAY_SIZE(mxt_td60_i2c2_devices));
-
-	imx27_add_imx_i2c(0, &mxt_td60_i2c0_data);
-	imx27_add_imx_i2c(1, &mxt_td60_i2c1_data);
-	imx27_add_imx_fb(&mxt_td60_fb_data);
-	imx27_add_mxc_mmc(0, &sdhc1_pdata);
-	imx27_add_fec(NULL);
-}
-
-static void __init mxt_td60_timer_init(void)
-{
-	mx27_clocks_init(26000000);
-}
-
-MACHINE_START(MXT_TD60, "Maxtrack i-MXT TD60")
-	/* maintainer: Maxtrack Industrial */
-	.atag_offset = 0x100,
-	.map_io = mx27_map_io,
-	.init_early = imx27_init_early,
-	.init_irq = mx27_init_irq,
-	.init_time	= mxt_td60_timer_init,
-	.init_machine = mxt_td60_board_init,
-	.restart	= mxc_restart,
-MACHINE_END

arch/arm/mach-imx/mach-pcm038.c

@@ -1,358 +0,0 @@
-/*
- * Copyright 2007 Robert Schwebel <r.schwebel@pengutronix.de>, Pengutronix
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/i2c.h>
-#include <linux/platform_data/at24.h>
-#include <linux/io.h>
-#include <linux/mtd/plat-ram.h>
-#include <linux/mtd/physmap.h>
-#include <linux/platform_device.h>
-#include <linux/regulator/machine.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "board-pcm038.h"
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-#include "ulpi.h"
-
-static const int pcm038_pins[] __initconst = {
-	/* UART1 */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-	/* UART2 */
-	PE3_PF_UART2_CTS,
-	PE4_PF_UART2_RTS,
-	PE6_PF_UART2_TXD,
-	PE7_PF_UART2_RXD,
-	/* UART3 */
-	PE8_PF_UART3_TXD,
-	PE9_PF_UART3_RXD,
-	PE10_PF_UART3_CTS,
-	PE11_PF_UART3_RTS,
-	/* FEC */
-	PD0_AIN_FEC_TXD0,
-	PD1_AIN_FEC_TXD1,
-	PD2_AIN_FEC_TXD2,
-	PD3_AIN_FEC_TXD3,
-	PD4_AOUT_FEC_RX_ER,
-	PD5_AOUT_FEC_RXD1,
-	PD6_AOUT_FEC_RXD2,
-	PD7_AOUT_FEC_RXD3,
-	PD8_AF_FEC_MDIO,
-	PD9_AIN_FEC_MDC,
-	PD10_AOUT_FEC_CRS,
-	PD11_AOUT_FEC_TX_CLK,
-	PD12_AOUT_FEC_RXD0,
-	PD13_AOUT_FEC_RX_DV,
-	PD14_AOUT_FEC_RX_CLK,
-	PD15_AOUT_FEC_COL,
-	PD16_AIN_FEC_TX_ER,
-	PF23_AIN_FEC_TX_EN,
-	/* I2C2 */
-	PC5_PF_I2C2_SDA,
-	PC6_PF_I2C2_SCL,
-	/* SPI1 */
-	PD25_PF_CSPI1_RDY,
-	PD29_PF_CSPI1_SCLK,
-	PD30_PF_CSPI1_MISO,
-	PD31_PF_CSPI1_MOSI,
-	/* SSI1 */
-	PC20_PF_SSI1_FS,
-	PC21_PF_SSI1_RXD,
-	PC22_PF_SSI1_TXD,
-	PC23_PF_SSI1_CLK,
-	/* SSI4 */
-	PC16_PF_SSI4_FS,
-	PC17_PF_SSI4_RXD,
-	PC18_PF_SSI4_TXD,
-	PC19_PF_SSI4_CLK,
-	/* USB host */
-	PA0_PF_USBH2_CLK,
-	PA1_PF_USBH2_DIR,
-	PA2_PF_USBH2_DATA7,
-	PA3_PF_USBH2_NXT,
-	PA4_PF_USBH2_STP,
-	PD19_AF_USBH2_DATA4,
-	PD20_AF_USBH2_DATA3,
-	PD21_AF_USBH2_DATA6,
-	PD22_AF_USBH2_DATA0,
-	PD23_AF_USBH2_DATA2,
-	PD24_AF_USBH2_DATA1,
-	PD26_AF_USBH2_DATA5,
-};
-
-/*
- * Phytec's PCM038 comes with 2MiB battery buffered SRAM,
- * 16 bit width
- */
-
-static struct platdata_mtd_ram pcm038_sram_data = {
-	.bankwidth = 2,
-};
-
-static struct resource pcm038_sram_resource = {
-	.start = MX27_CS1_BASE_ADDR,
-	.end   = MX27_CS1_BASE_ADDR + 512 * 1024 - 1,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device pcm038_sram_mtd_device = {
-	.name = "mtd-ram",
-	.id = 0,
-	.dev = {
-		.platform_data = &pcm038_sram_data,
-	},
-	.num_resources = 1,
-	.resource = &pcm038_sram_resource,
-};
-
-/*
- * Phytec's phyCORE-i.MX27 comes with 32MiB flash,
- * 16 bit width
- */
-static struct physmap_flash_data pcm038_flash_data = {
-	.width = 2,
-};
-
-static struct resource pcm038_flash_resource = {
-	.start = 0xc0000000,
-	.end   = 0xc1ffffff,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device pcm038_nor_mtd_device = {
-	.name = "physmap-flash",
-	.id = 0,
-	.dev = {
-		.platform_data = &pcm038_flash_data,
-	},
-	.num_resources = 1,
-	.resource = &pcm038_flash_resource,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct mxc_nand_platform_data
-pcm038_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
-	&pcm038_nor_mtd_device,
-	&pcm038_sram_mtd_device,
-};
-
-/* On pcm038 there's a sram attached to CS1, we enable the chipselect here and
- * setup other stuffs to access the sram. */
-static void __init pcm038_init_sram(void)
-{
-	__raw_writel(0x0000d843, MX27_IO_ADDRESS(MX27_WEIM_CSCRxU(1)));
-	__raw_writel(0x22252521, MX27_IO_ADDRESS(MX27_WEIM_CSCRxL(1)));
-	__raw_writel(0x22220a00, MX27_IO_ADDRESS(MX27_WEIM_CSCRxA(1)));
-}
-
-static const struct imxi2c_platform_data pcm038_i2c1_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct at24_platform_data board_eeprom = {
-	.byte_len = 4096,
-	.page_size = 32,
-	.flags = AT24_FLAG_ADDR16,
-};
-
-static struct i2c_board_info pcm038_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */
-		.platform_data = &board_eeprom,
-	}, {
-		I2C_BOARD_INFO("pcf8563", 0x51),
-	}, {
-		I2C_BOARD_INFO("lm75", 0x4a),
-	}
-};
-
-static int pcm038_spi_cs[] = {GPIO_PORTD + 28};
-
-static const struct spi_imx_master pcm038_spi0_data __initconst = {
-	.chipselect = pcm038_spi_cs,
-	.num_chipselect = ARRAY_SIZE(pcm038_spi_cs),
-};
-
-static struct regulator_consumer_supply sdhc1_consumers[] = {
-	{
-		.dev_name = "imx21-mmc.1",
-		.supply	= "sdhc_vcc",
-	},
-};
-
-static struct regulator_init_data sdhc1_data = {
-	.constraints = {
-		.min_uV = 3000000,
-		.max_uV = 3400000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-			REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL |
-			REGULATOR_MODE_FAST,
-		.always_on = 0,
-		.boot_on = 0,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(sdhc1_consumers),
-	.consumer_supplies = sdhc1_consumers,
-};
-
-static struct regulator_consumer_supply cam_consumers[] = {
-	{
-		.dev_name = NULL,
-		.supply	= "imx_cam_vcc",
-	},
-};
-
-static struct regulator_init_data cam_data = {
-	.constraints = {
-		.min_uV = 3000000,
-		.max_uV = 3400000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-			REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL |
-			REGULATOR_MODE_FAST,
-		.always_on = 0,
-		.boot_on = 0,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(cam_consumers),
-	.consumer_supplies = cam_consumers,
-};
-
-static struct mc13xxx_regulator_init_data pcm038_regulators[] = {
-	{
-		.id = MC13783_REG_VCAM,
-		.init_data = &cam_data,
-	}, {
-		.id = MC13783_REG_VMMC1,
-		.init_data = &sdhc1_data,
-	},
-};
-
-static struct mc13xxx_platform_data pcm038_pmic = {
-	.regulators = {
-		.regulators = pcm038_regulators,
-		.num_regulators = ARRAY_SIZE(pcm038_regulators),
-	},
-	.flags = MC13XXX_USE_ADC | MC13XXX_USE_TOUCHSCREEN,
-};
-
-static struct spi_board_info pcm038_spi_board_info[] __initdata = {
-	{
-		.modalias = "mc13783",
-		/* irq number is run-time assigned */
-		.max_speed_hz = 300000,
-		.bus_num = 0,
-		.chip_select = 0,
-		.platform_data = &pcm038_pmic,
-		.mode = SPI_CS_HIGH,
-	}
-};
-
-static int pcm038_usbh2_init(struct platform_device *pdev)
-{
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
-			MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static const struct mxc_usbh_platform_data usbh2_pdata __initconst = {
-	.init	= pcm038_usbh2_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static void __init pcm038_init(void)
-{
-	imx27_soc_init();
-
-	mxc_gpio_setup_multiple_pins(pcm038_pins, ARRAY_SIZE(pcm038_pins),
-			"PCM038");
-
-	pcm038_init_sram();
-
-	imx27_add_imx_uart0(&uart_pdata);
-	imx27_add_imx_uart1(&uart_pdata);
-	imx27_add_imx_uart2(&uart_pdata);
-
-	mxc_gpio_mode(PE16_AF_OWIRE);
-	imx27_add_mxc_nand(&pcm038_nand_board_info);
-
-	/* only the i2c master 1 is used on this CPU card */
-	i2c_register_board_info(1, pcm038_i2c_devices,
-				ARRAY_SIZE(pcm038_i2c_devices));
-
-	imx27_add_imx_i2c(1, &pcm038_i2c1_data);
-
-	/* PE18 for user-LED D40 */
-	mxc_gpio_mode(GPIO_PORTE | 18 | GPIO_GPIO | GPIO_OUT);
-
-	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
-
-	/* MC13783 IRQ */
-	mxc_gpio_mode(GPIO_PORTB | 23 | GPIO_GPIO | GPIO_IN);
-
-	imx27_add_spi_imx0(&pcm038_spi0_data);
-	pcm038_spi_board_info[0].irq = gpio_to_irq(IMX_GPIO_NR(2, 23));
-	spi_register_board_info(pcm038_spi_board_info,
-				ARRAY_SIZE(pcm038_spi_board_info));
-
-	imx27_add_mxc_ehci_hs(2, &usbh2_pdata);
-
-	imx27_add_fec(NULL);
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-	imx27_add_imx2_wdt();
-	imx27_add_mxc_w1();
-
-#ifdef CONFIG_MACH_PCM970_BASEBOARD
-	pcm970_baseboard_init();
-#endif
-}
-
-static void __init pcm038_timer_init(void)
-{
-	mx27_clocks_init(26000000);
-}
-
-MACHINE_START(PCM038, "phyCORE-i.MX27")
-	.atag_offset = 0x100,
-	.map_io = mx27_map_io,
-	.init_early = imx27_init_early,
-	.init_irq = mx27_init_irq,
-	.init_time	= pcm038_timer_init,
-	.init_machine = pcm038_init,
-	.restart	= mxc_restart,
-MACHINE_END

arch/arm/mach-imx/pcm970-baseboard.c

@@ -1,231 +0,0 @@
-/*
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/irq.h>
-#include <linux/platform_device.h>
-#include <linux/can/platform/sja1000.h>
-
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-
-static const int pcm970_pins[] __initconst = {
-	/* SDHC */
-	PB4_PF_SD2_D0,
-	PB5_PF_SD2_D1,
-	PB6_PF_SD2_D2,
-	PB7_PF_SD2_D3,
-	PB8_PF_SD2_CMD,
-	PB9_PF_SD2_CLK,
-	/* display */
-	PA5_PF_LSCLK,
-	PA6_PF_LD0,
-	PA7_PF_LD1,
-	PA8_PF_LD2,
-	PA9_PF_LD3,
-	PA10_PF_LD4,
-	PA11_PF_LD5,
-	PA12_PF_LD6,
-	PA13_PF_LD7,
-	PA14_PF_LD8,
-	PA15_PF_LD9,
-	PA16_PF_LD10,
-	PA17_PF_LD11,
-	PA18_PF_LD12,
-	PA19_PF_LD13,
-	PA20_PF_LD14,
-	PA21_PF_LD15,
-	PA22_PF_LD16,
-	PA23_PF_LD17,
-	PA24_PF_REV,
-	PA25_PF_CLS,
-	PA26_PF_PS,
-	PA27_PF_SPL_SPR,
-	PA28_PF_HSYNC,
-	PA29_PF_VSYNC,
-	PA30_PF_CONTRAST,
-	PA31_PF_OE_ACD,
-	/*
-	 * it seems the data line misses a pullup, so we must enable
-	 * the internal pullup as a local workaround
-	 */
-	PD17_PF_I2C_DATA | GPIO_PUEN,
-	PD18_PF_I2C_CLK,
-	/* Camera */
-	PB10_PF_CSI_D0,
-	PB11_PF_CSI_D1,
-	PB12_PF_CSI_D2,
-	PB13_PF_CSI_D3,
-	PB14_PF_CSI_D4,
-	PB15_PF_CSI_MCLK,
-	PB16_PF_CSI_PIXCLK,
-	PB17_PF_CSI_D5,
-	PB18_PF_CSI_D6,
-	PB19_PF_CSI_D7,
-	PB20_PF_CSI_VSYNC,
-	PB21_PF_CSI_HSYNC,
-};
-
-static int pcm970_sdhc2_get_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO_PORTC + 28);
-}
-
-static int pcm970_sdhc2_init(struct device *dev, irq_handler_t detect_irq, void *data)
-{
-	int ret;
-
-	ret = request_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), detect_irq,
-			  IRQF_TRIGGER_FALLING, "imx-mmc-detect", data);
-	if (ret)
-		return ret;
-
-	ret = gpio_request(GPIO_PORTC + 28, "imx-mmc-ro");
-	if (ret) {
-		free_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), data);
-		return ret;
-	}
-
-	gpio_direction_input(GPIO_PORTC + 28);
-
-	return 0;
-}
-
-static void pcm970_sdhc2_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), data);
-	gpio_free(GPIO_PORTC + 28);
-}
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
-	.get_ro = pcm970_sdhc2_get_ro,
-	.init = pcm970_sdhc2_init,
-	.exit = pcm970_sdhc2_exit,
-};
-
-static struct imx_fb_videomode pcm970_modes[] = {
-	{
-		.mode = {
-			.name		= "Sharp-LQ035Q7",
-			.refresh	= 60,
-			.xres		= 240,
-			.yres		= 320,
-			.pixclock	= 188679, /* in ps (5.3MHz) */
-			.hsync_len	= 7,
-			.left_margin	= 5,
-			.right_margin	= 16,
-			.vsync_len	= 1,
-			.upper_margin	= 7,
-			.lower_margin	= 9,
-		},
-		/*
-		 * - HSYNC active high
-		 * - VSYNC active high
-		 * - clk notenabled while idle
-		 * - clock not inverted
-		 * - data not inverted
-		 * - data enable low active
-		 * - enable sharp mode
-		 */
-		.pcr		= 0xF00080C0,
-		.bpp		= 16,
-	}, {
-		.mode = {
-			.name		= "TX090",
-			.refresh	= 60,
-			.xres		= 240,
-			.yres		= 320,
-			.pixclock	= 38255,
-			.left_margin	= 144,
-			.right_margin	= 0,
-			.upper_margin	= 7,
-			.lower_margin	= 40,
-			.hsync_len	= 96,
-			.vsync_len	= 1,
-		},
-		/*
-		 * - HSYNC active low (1 << 22)
-		 * - VSYNC active low (1 << 23)
-		 * - clk notenabled while idle
-		 * - clock not inverted
-		 * - data not inverted
-		 * - data enable low active
-		 * - enable sharp mode
-		 */
-		.pcr = 0xF0008080 | (1<<22) | (1<<23) | (1<<19),
-		.bpp = 32,
-	},
-};
-
-static const struct imx_fb_platform_data pcm038_fb_data __initconst = {
-	.mode = pcm970_modes,
-	.num_modes = ARRAY_SIZE(pcm970_modes),
-
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00020010,
-};
-
-static struct resource pcm970_sja1000_resources[] = {
-	{
-		.start   = MX27_CS4_BASE_ADDR,
-		.end     = MX27_CS4_BASE_ADDR + 0x100 - 1,
-		.flags   = IORESOURCE_MEM,
-	}, {
-		/* irq number is run-time assigned */
-		.flags   = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
-	},
-};
-
-static struct sja1000_platform_data pcm970_sja1000_platform_data = {
-	.osc_freq	= 16000000,
-	.ocr		= OCR_TX1_PULLDOWN | OCR_TX0_PUSHPULL,
-	.cdr		= CDR_CBP,
-};
-
-static struct platform_device pcm970_sja1000 = {
-	.name = "sja1000_platform",
-	.dev = {
-		.platform_data = &pcm970_sja1000_platform_data,
-	},
-	.resource = pcm970_sja1000_resources,
-	.num_resources = ARRAY_SIZE(pcm970_sja1000_resources),
-};
-
-/*
- * system init for baseboard usage. Will be called by pcm038 init.
- *
- * Add platform devices present on this baseboard and init
- * them from CPU side as far as required to use them later on
- */
-void __init pcm970_baseboard_init(void)
-{
-	mxc_gpio_setup_multiple_pins(pcm970_pins, ARRAY_SIZE(pcm970_pins),
-			"PCM970");
-
-	imx27_add_imx_fb(&pcm038_fb_data);
-	mxc_gpio_mode(GPIO_PORTC | 28 | GPIO_GPIO | GPIO_IN);
-	imx27_add_mxc_mmc(1, &sdhc_pdata);
-	pcm970_sja1000_resources[1].start = gpio_to_irq(IMX_GPIO_NR(5, 19));
-	pcm970_sja1000_resources[1].end = gpio_to_irq(IMX_GPIO_NR(5, 19));
-	platform_device_register(&pcm970_sja1000);
-}

arch/arm/mach-imx/platsmp.c

@@ -20,8 +20,6 @@
 #include "common.h"
 #include "hardware.h"
 
-#define SCU_STANDBY_ENABLE	(1 << 5)
-
 u32 g_diag_reg;
 static void __iomem *scu_base;
 
@@ -45,14 +43,6 @@ void __init imx_scu_map_io(void)
 	scu_base = IMX_IO_ADDRESS(base);
 }
 
-void imx_scu_standby_enable(void)
-{
-	u32 val = readl_relaxed(scu_base);
-
-	val |= SCU_STANDBY_ENABLE;
-	writel_relaxed(val, scu_base);
-}
-
 static int imx_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	imx_set_cpu_jump(cpu, v7_secondary_startup);

arch/arm/mach-omap2/board-flash.c

@@ -142,7 +142,7 @@ __init board_nand_init(struct mtd_partition *nand_parts, u8 nr_parts, u8 cs,
 	board_nand_data.nr_parts	= nr_parts;
 	board_nand_data.devsize		= nand_type;
 
-	board_nand_data.ecc_opt = OMAP_ECC_HAM1_CODE_HW;
+	board_nand_data.ecc_opt = OMAP_ECC_HAM1_CODE_SW;
 	gpmc_nand_init(&board_nand_data, gpmc_t);
 }
 #endif /* CONFIG_MTD_NAND_OMAP2 || CONFIG_MTD_NAND_OMAP2_MODULE */

arch/arm/mach-omap2/gpmc-nand.c

@@ -49,7 +49,8 @@ static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
 		return 0;
 
 	/* legacy platforms support only HAM1 (1-bit Hamming) ECC scheme */
-	if (ecc_opt == OMAP_ECC_HAM1_CODE_HW)
+	if (ecc_opt == OMAP_ECC_HAM1_CODE_HW ||
+	    ecc_opt == OMAP_ECC_HAM1_CODE_SW)
 		return 1;
 	else
 		return 0;

arch/arm/mach-omap2/gpmc.c

@@ -1403,8 +1403,11 @@ static int gpmc_probe_nand_child(struct platform_device *pdev,
 		pr_err("%s: ti,nand-ecc-opt not found\n", __func__);
 		return -ENODEV;
 	}
-	if (!strcmp(s, "ham1") || !strcmp(s, "sw") ||
-		!strcmp(s, "hw") || !strcmp(s, "hw-romcode"))
+
+	if (!strcmp(s, "sw"))
+		gpmc_nand_data->ecc_opt = OMAP_ECC_HAM1_CODE_SW;
+	else if (!strcmp(s, "ham1") ||
+		 !strcmp(s, "hw") || !strcmp(s, "hw-romcode"))
 		gpmc_nand_data->ecc_opt =
 				OMAP_ECC_HAM1_CODE_HW;
 	else if (!strcmp(s, "bch4"))

arch/arm/mach-omap2/id.c

@@ -663,7 +663,7 @@ void __init dra7xxx_check_revision(void)
 
 	default:
 		/* Unknown default to latest silicon rev as default*/
-		pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%d)\n",
+		pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%x)\n",
 			__func__, idcode, hawkeye, rev);
 		omap_revision = DRA752_REV_ES1_1;
 	}

arch/arm/mach-omap2/omap_device.c

@@ -56,7 +56,7 @@ static void _add_clkdev(struct omap_device *od, const char *clk_alias,
 
 	r = clk_get_sys(dev_name(&od->pdev->dev), clk_alias);
 	if (!IS_ERR(r)) {
-		dev_warn(&od->pdev->dev,
+		dev_dbg(&od->pdev->dev,
 			 "alias %s already exists\n", clk_alias);
 		clk_put(r);
 		return;

arch/arm/mach-omap2/omap_hwmod.c

@@ -2185,6 +2185,8 @@ static int _enable(struct omap_hwmod *oh)
 			 oh->mux->pads_dynamic))) {
 		omap_hwmod_mux(oh->mux, _HWMOD_STATE_ENABLED);
 		_reconfigure_io_chain();
+	} else if (oh->flags & HWMOD_FORCE_MSTANDBY) {
+		_reconfigure_io_chain();
 	}
 
 	_add_initiator_dep(oh, mpu_oh);
@@ -2291,6 +2293,8 @@ static int _idle(struct omap_hwmod *oh)
 	if (oh->mux && oh->mux->pads_dynamic) {
 		omap_hwmod_mux(oh->mux, _HWMOD_STATE_IDLE);
 		_reconfigure_io_chain();
+	} else if (oh->flags & HWMOD_FORCE_MSTANDBY) {
+		_reconfigure_io_chain();
 	}
 
 	oh->_state = _HWMOD_STATE_IDLE;
@@ -3345,6 +3349,9 @@ int __init omap_hwmod_register_links(struct omap_hwmod_ocp_if **ois)
 	if (!ois)
 		return 0;
 
+	if (ois[0] == NULL) /* Empty list */
+		return 0;
+
 	if (!linkspace) {
 		if (_alloc_linkspace(ois)) {
 			pr_err("omap_hwmod: could not allocate link space\n");

arch/arm/mach-omap2/omap_hwmod_7xx_data.c

@@ -35,6 +35,7 @@
 #include "i2c.h"
 #include "mmc.h"
 #include "wd_timer.h"
+#include "soc.h"
 
 /* Base offset for all DRA7XX interrupts external to MPUSS */
 #define DRA7XX_IRQ_GIC_START	32
@@ -3261,7 +3262,6 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = {
 	&dra7xx_l4_per3__usb_otg_ss1,
 	&dra7xx_l4_per3__usb_otg_ss2,
 	&dra7xx_l4_per3__usb_otg_ss3,
-	&dra7xx_l4_per3__usb_otg_ss4,
 	&dra7xx_l3_main_1__vcp1,
 	&dra7xx_l4_per2__vcp1,
 	&dra7xx_l3_main_1__vcp2,
@@ -3270,8 +3270,26 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = {
 	NULL,
 };
 
+static struct omap_hwmod_ocp_if *dra74x_hwmod_ocp_ifs[] __initdata = {
+	&dra7xx_l4_per3__usb_otg_ss4,
+	NULL,
+};
+
+static struct omap_hwmod_ocp_if *dra72x_hwmod_ocp_ifs[] __initdata = {
+	NULL,
+};
+
 int __init dra7xx_hwmod_init(void)
 {
+	int ret;
+
 	omap_hwmod_init();
-	return omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs);
+	ret = omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs);
+
+	if (!ret && soc_is_dra74x())
+		return omap_hwmod_register_links(dra74x_hwmod_ocp_ifs);
+	else if (!ret && soc_is_dra72x())
+		return omap_hwmod_register_links(dra72x_hwmod_ocp_ifs);
+
+	return ret;
 }

arch/arm/mach-omap2/soc.h

@@ -245,6 +245,8 @@ IS_AM_SUBCLASS(437x, 0x437)
 #define soc_is_omap54xx()		0
 #define soc_is_omap543x()		0
 #define soc_is_dra7xx()			0
+#define soc_is_dra74x()			0
+#define soc_is_dra72x()			0
 
 #if defined(MULTI_OMAP2)
 # if defined(CONFIG_ARCH_OMAP2)
@@ -393,7 +395,11 @@ IS_OMAP_TYPE(3430, 0x3430)
 
 #if defined(CONFIG_SOC_DRA7XX)
 #undef soc_is_dra7xx
+#undef soc_is_dra74x
+#undef soc_is_dra72x
 #define soc_is_dra7xx()	(of_machine_is_compatible("ti,dra7"))
+#define soc_is_dra74x()	(of_machine_is_compatible("ti,dra74"))
+#define soc_is_dra72x()	(of_machine_is_compatible("ti,dra72"))
 #endif
 
 /* Various silicon revisions for omap2 */

arch/arm/mach-shmobile/clock-r8a7790.c

@@ -183,8 +183,8 @@ enum {
 
 static struct clk div4_clks[DIV4_NR] = {
 	[DIV4_SDH] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 8, 0x0dff, CLK_ENABLE_ON_INIT),
-	[DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1de0, CLK_ENABLE_ON_INIT),
-	[DIV4_SD1] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 0, 0x1de0, CLK_ENABLE_ON_INIT),
+	[DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1df0, CLK_ENABLE_ON_INIT),
+	[DIV4_SD1] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 0, 0x1df0, CLK_ENABLE_ON_INIT),
 };
 
 /* DIV6 clocks */

arch/arm/mach-shmobile/clock-r8a7791.c

@@ -152,7 +152,7 @@ enum {
 
 static struct clk div4_clks[DIV4_NR] = {
 	[DIV4_SDH] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 8, 0x0dff, CLK_ENABLE_ON_INIT),
-	[DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1de0, CLK_ENABLE_ON_INIT),
+	[DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1df0, CLK_ENABLE_ON_INIT),
 };
 
 /* DIV6 clocks */

arch/arm/mach-shmobile/clock-sh73a0.c

@@ -644,7 +644,7 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]), /* SCIFA5 */
 	CLKDEV_DEV_ID("e6cb0000.serial", &mstp_clks[MSTP207]), /* SCIFA5 */
 	CLKDEV_DEV_ID("sh-sci.8", &mstp_clks[MSTP206]), /* SCIFB */
-	CLKDEV_DEV_ID("0xe6c3000.serial", &mstp_clks[MSTP206]), /* SCIFB */
+	CLKDEV_DEV_ID("e6c3000.serial", &mstp_clks[MSTP206]), /* SCIFB */
 	CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]), /* SCIFA0 */
 	CLKDEV_DEV_ID("e6c40000.serial", &mstp_clks[MSTP204]), /* SCIFA0 */
 	CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]), /* SCIFA1 */

arch/arm/mach-vexpress/spc.c

@@ -426,9 +426,15 @@ static int ve_spc_populate_opps(uint32_t cluster)
 
 static int ve_init_opp_table(struct device *cpu_dev)
 {
-	int cluster = topology_physical_package_id(cpu_dev->id);
-	int idx, ret = 0, max_opp = info->num_opps[cluster];
-	struct ve_spc_opp *opps = info->opps[cluster];
+	int cluster;
+	int idx, ret = 0, max_opp;
+	struct ve_spc_opp *opps;
+
+	cluster = topology_physical_package_id(cpu_dev->id);
+	cluster = cluster < 0 ? 0 : cluster;
+
+	max_opp = info->num_opps[cluster];
+	opps = info->opps[cluster];
 
 	for (idx = 0; idx < max_opp; idx++, opps++) {
 		ret = dev_pm_opp_add(cpu_dev, opps->freq * 1000, opps->u_volt);
@@ -537,6 +543,8 @@ static struct clk *ve_spc_clk_register(struct device *cpu_dev)
 	spc->hw.init = &init;
 	spc->cluster = topology_physical_package_id(cpu_dev->id);
 
+	spc->cluster = spc->cluster < 0 ? 0 : spc->cluster;
+
 	init.name = dev_name(cpu_dev);
 	init.ops = &clk_spc_ops;
 	init.flags = CLK_IS_ROOT | CLK_GET_RATE_NOCACHE;

arch/arm/mm/abort-ev6.S

@@ -17,12 +17,6 @@
  */
 	.align	5
 ENTRY(v6_early_abort)
-#ifdef CONFIG_CPU_V6
-	sub	r1, sp, #4			@ Get unused stack location
-	strex	r0, r1, [r1]			@ Clear the exclusive monitor
-#elif defined(CONFIG_CPU_32v6K)
-	clrex
-#endif
 	mrc	p15, 0, r1, c5, c0, 0		@ get FSR
 	mrc	p15, 0, r0, c6, c0, 0		@ get FAR
 /*

arch/arm/mm/abort-ev7.S

@@ -13,12 +13,6 @@
  */
 	.align	5
 ENTRY(v7_early_abort)
-	/*
-	 * The effect of data aborts on on the exclusive access monitor are
-	 * UNPREDICTABLE. Do a CLREX to clear the state
-	 */
-	clrex
-
 	mrc	p15, 0, r1, c5, c0, 0		@ get FSR
 	mrc	p15, 0, r0, c6, c0, 0		@ get FAR
 

arch/hexagon/mm/cache.c

@@ -68,6 +68,7 @@ void flush_icache_range(unsigned long start, unsigned long end)
 	);
 	local_irq_restore(flags);
 }
+EXPORT_SYMBOL(flush_icache_range);
 
 void hexagon_clean_dcache_range(unsigned long start, unsigned long end)
 {

arch/ia64/Kconfig

@@ -549,8 +549,6 @@ source "drivers/sn/Kconfig"
 config KEXEC
 	bool "kexec system call"
 	depends on !IA64_HP_SIM && (!SMP || HOTPLUG_CPU)
-	select CRYPTO
-	select CRYPTO_SHA256
 	help
 	  kexec is a system call that implements the ability to shutdown your
 	  current kernel, and to start another kernel.  It is like a reboot

arch/m68k/Kconfig

@@ -91,8 +91,6 @@ config MMU_SUN3
 config KEXEC
 	bool "kexec system call"
 	depends on M68KCLASSIC
-	select CRYPTO
-	select CRYPTO_SHA256
 	help
 	  kexec is a system call that implements the ability to shutdown your
 	  current kernel, and to start another kernel.  It is like a reboot

arch/mips/Kconfig

@@ -2396,8 +2396,6 @@ source "kernel/Kconfig.preempt"
 
 config KEXEC
 	bool "Kexec system call"
-	select CRYPTO
-	select CRYPTO_SHA256
 	help
 	  kexec is a system call that implements the ability to shutdown your
 	  current kernel, and to start another kernel.  It is like a reboot

arch/powerpc/Kconfig

@@ -399,8 +399,6 @@ config PPC64_SUPPORTS_MEMORY_FAILURE
 config KEXEC
 	bool "kexec system call"
 	depends on (PPC_BOOK3S || FSL_BOOKE || (44x && !SMP))
-	select CRYPTO
-	select CRYPTO_SHA256
 	help
 	  kexec is a system call that implements the ability to shutdown your
 	  current kernel, and to start another kernel.  It is like a reboot

arch/s390/Kconfig

@@ -48,8 +48,6 @@ config ARCH_SUPPORTS_DEBUG_PAGEALLOC
 
 config KEXEC
 	def_bool y
-	select CRYPTO
-	select CRYPTO_SHA256
 
 config AUDIT_ARCH
 	def_bool y

arch/s390/include/uapi/asm/unistd.h

@@ -283,7 +283,10 @@
 #define __NR_sched_setattr	345
 #define __NR_sched_getattr	346
 #define __NR_renameat2		347
-#define NR_syscalls 348
+#define __NR_seccomp		348
+#define __NR_getrandom		349
+#define __NR_memfd_create	350
+#define NR_syscalls 351
 
 /* 
  * There are some system calls that are not present on 64 bit, some

arch/s390/kernel/compat_wrapper.c

@@ -214,3 +214,6 @@ COMPAT_SYSCALL_WRAP3(finit_module, int, fd, const char __user *, uargs, int, fla
 COMPAT_SYSCALL_WRAP3(sched_setattr, pid_t, pid, struct sched_attr __user *, attr, unsigned int, flags);
 COMPAT_SYSCALL_WRAP4(sched_getattr, pid_t, pid, struct sched_attr __user *, attr, unsigned int, size, unsigned int, flags);
 COMPAT_SYSCALL_WRAP5(renameat2, int, olddfd, const char __user *, oldname, int, newdfd, const char __user *, newname, unsigned int, flags);
+COMPAT_SYSCALL_WRAP3(seccomp, unsigned int, op, unsigned int, flags, const char __user *, uargs)
+COMPAT_SYSCALL_WRAP3(getrandom, char __user *, buf, size_t, count, unsigned int, flags)
+COMPAT_SYSCALL_WRAP2(memfd_create, const char __user *, uname, unsigned int, flags)

arch/s390/kernel/ipl.c

@@ -2060,6 +2060,13 @@ void s390_reset_system(void (*func)(void *), void *data)
 	S390_lowcore.program_new_psw.addr =
 		PSW_ADDR_AMODE | (unsigned long) s390_base_pgm_handler;
 
+	/*
+	 * Clear subchannel ID and number to signal new kernel that no CCW or
+	 * SCSI IPL has been done (for kexec and kdump)
+	 */
+	S390_lowcore.subchannel_id = 0;
+	S390_lowcore.subchannel_nr = 0;
+
 	/* Store status at absolute zero */
 	store_status();
 

arch/s390/kernel/setup.c

@@ -24,6 +24,7 @@
 #include <linux/stddef.h>
 #include <linux/unistd.h>
 #include <linux/ptrace.h>
+#include <linux/random.h>
 #include <linux/user.h>
 #include <linux/tty.h>
 #include <linux/ioport.h>
@@ -61,6 +62,7 @@
 #include <asm/diag.h>
 #include <asm/os_info.h>
 #include <asm/sclp.h>
+#include <asm/sysinfo.h>
 #include "entry.h"
 
 /*
@@ -766,6 +768,7 @@ static void __init setup_hwcaps(void)
 #endif
 
 	get_cpu_id(&cpu_id);
+	add_device_randomness(&cpu_id, sizeof(cpu_id));
 	switch (cpu_id.machine) {
 	case 0x9672:
 #if !defined(CONFIG_64BIT)
@@ -803,6 +806,19 @@ static void __init setup_hwcaps(void)
 	}
 }
 
+/*
+ * Add system information as device randomness
+ */
+static void __init setup_randomness(void)
+{
+	struct sysinfo_3_2_2 *vmms;
+
+	vmms = (struct sysinfo_3_2_2 *) alloc_page(GFP_KERNEL);
+	if (vmms && stsi(vmms, 3, 2, 2) == 0 && vmms->count)
+		add_device_randomness(&vmms, vmms->count);
+	free_page((unsigned long) vmms);
+}
+
 /*
  * Setup function called from init/main.c just after the banner
  * was printed.
@@ -901,6 +917,9 @@ void __init setup_arch(char **cmdline_p)
 
 	/* Setup zfcpdump support */
 	setup_zfcpdump();
+
+	/* Add system specific data to the random pool */
+	setup_randomness();
 }
 
 #ifdef CONFIG_32BIT

arch/s390/kernel/syscalls.S

@@ -356,3 +356,6 @@ SYSCALL(sys_finit_module,sys_finit_module,compat_sys_finit_module)
 SYSCALL(sys_sched_setattr,sys_sched_setattr,compat_sys_sched_setattr) /* 345 */
 SYSCALL(sys_sched_getattr,sys_sched_getattr,compat_sys_sched_getattr)
 SYSCALL(sys_renameat2,sys_renameat2,compat_sys_renameat2)
+SYSCALL(sys_seccomp,sys_seccomp,compat_sys_seccomp)
+SYSCALL(sys_getrandom,sys_getrandom,compat_sys_getrandom)
+SYSCALL(sys_memfd_create,sys_memfd_create,compat_sys_memfd_create) /* 350 */

arch/sh/Kconfig

@@ -598,8 +598,6 @@ source kernel/Kconfig.hz
 config KEXEC
 	bool "kexec system call (EXPERIMENTAL)"
 	depends on SUPERH32 && MMU
-	select CRYPTO
-	select CRYPTO_SHA256
 	help
 	  kexec is a system call that implements the ability to shutdown your
 	  current kernel, and to start another kernel.  It is like a reboot

arch/sh/mm/cache.c

@@ -229,6 +229,7 @@ void flush_icache_range(unsigned long start, unsigned long end)
 
 	cacheop_on_each_cpu(local_flush_icache_range, (void *)&data, 1);
 }
+EXPORT_SYMBOL(flush_icache_range);
 
 void flush_icache_page(struct vm_area_struct *vma, struct page *page)
 {

arch/tile/Kconfig

@@ -191,8 +191,6 @@ source "kernel/Kconfig.hz"
 
 config KEXEC
 	bool "kexec system call"
-	select CRYPTO
-	select CRYPTO_SHA256
 	---help---
 	  kexec is a system call that implements the ability to shutdown your
 	  current kernel, and to start another kernel.  It is like a reboot

arch/tile/kernel/smp.c

@@ -183,6 +183,7 @@ void flush_icache_range(unsigned long start, unsigned long end)
 		preempt_enable();
 	}
 }
+EXPORT_SYMBOL(flush_icache_range);
 
 
 /* Called when smp_send_reschedule() triggers IRQ_RESCHEDULE. */

arch/unicore32/kernel/signal.c

@@ -254,7 +254,8 @@ static int setup_frame(struct ksignal *ksig, sigset_t *set,
 
 	err |= setup_sigframe(frame, regs, set);
 	if (err == 0)
-		err |= setup_return(regs, &ksig->ka, frame->retcode, frame, usig);
+		err |= setup_return(regs, &ksig->ka, frame->retcode, frame,
+				    ksig->sig);
 
 	return err;
 }
@@ -276,7 +277,8 @@ static int setup_rt_frame(struct ksignal *ksig, sigset_t *set,
 	err |= __save_altstack(&frame->sig.uc.uc_stack, regs->UCreg_sp);
 	err |= setup_sigframe(&frame->sig, regs, set);
 	if (err == 0)
-		err |= setup_return(regs, &ksig->ka, frame->sig.retcode, frame, usig);
+		err |= setup_return(regs, &ksig->ka, frame->sig.retcode, frame,
+				    ksig->sig);
 
 	if (err == 0) {
 		/*
@@ -303,7 +305,6 @@ static void handle_signal(struct ksignal *ksig, struct pt_regs *regs,
 			  int syscall)
 {
 	struct thread_info *thread = current_thread_info();
-	struct task_struct *tsk = current;
 	sigset_t *oldset = sigmask_to_save();
 	int usig = ksig->sig;
 	int ret;
@@ -373,7 +374,7 @@ static void do_signal(struct pt_regs *regs, int syscall)
 	if (!user_mode(regs))
 		return;
 
-	if (get_signsl(&ksig)) {
+	if (get_signal(&ksig)) {
 		handle_signal(&ksig, regs, syscall);
 		return;
 	}

arch/x86/Kbuild

@@ -17,6 +17,4 @@ obj-$(CONFIG_IA32_EMULATION) += ia32/
 obj-y += platform/
 obj-y += net/
 
-ifeq ($(CONFIG_X86_64),y)
-obj-$(CONFIG_KEXEC) += purgatory/
-endif
+obj-$(CONFIG_KEXEC_FILE) += purgatory/

arch/x86/Kconfig

@@ -1585,9 +1585,6 @@ source kernel/Kconfig.hz
 
 config KEXEC
 	bool "kexec system call"
-	select BUILD_BIN2C
-	select CRYPTO
-	select CRYPTO_SHA256
 	---help---
 	  kexec is a system call that implements the ability to shutdown your
 	  current kernel, and to start another kernel.  It is like a reboot
@@ -1602,9 +1599,22 @@ config KEXEC
 	  interface is strongly in flux, so no good recommendation can be
 	  made.
 
+config KEXEC_FILE
+	bool "kexec file based system call"
+	select BUILD_BIN2C
+	depends on KEXEC
+	depends on X86_64
+	depends on CRYPTO=y
+	depends on CRYPTO_SHA256=y
+	---help---
+	  This is new version of kexec system call. This system call is
+	  file based and takes file descriptors as system call argument
+	  for kernel and initramfs as opposed to list of segments as
+	  accepted by previous system call.
+
 config KEXEC_VERIFY_SIG
 	bool "Verify kernel signature during kexec_file_load() syscall"
-	depends on KEXEC
+	depends on KEXEC_FILE
 	---help---
 	  This option makes kernel signature verification mandatory for
 	  kexec_file_load() syscall. If kernel is signature can not be

arch/x86/Makefile

@@ -184,11 +184,8 @@ archheaders:
 	$(Q)$(MAKE) $(build)=arch/x86/syscalls all
 
 archprepare:
-ifeq ($(CONFIG_KEXEC),y)
-# Build only for 64bit. No loaders for 32bit yet.
- ifeq ($(CONFIG_X86_64),y)
+ifeq ($(CONFIG_KEXEC_FILE),y)
 	$(Q)$(MAKE) $(build)=arch/x86/purgatory arch/x86/purgatory/kexec-purgatory.c
- endif
 endif
 
 ###
@@ -254,6 +251,7 @@ archclean:
 	$(Q)rm -rf $(objtree)/arch/x86_64
 	$(Q)$(MAKE) $(clean)=$(boot)
 	$(Q)$(MAKE) $(clean)=arch/x86/tools
+	$(Q)$(MAKE) $(clean)=arch/x86/purgatory
 
 PHONY += kvmconfig
 kvmconfig:

arch/x86/include/asm/io_apic.h

@@ -227,6 +227,8 @@ static inline void io_apic_modify(unsigned int apic, unsigned int reg, unsigned
 
 extern void io_apic_eoi(unsigned int apic, unsigned int vector);
 
+extern bool mp_should_keep_irq(struct device *dev);
+
 #else  /* !CONFIG_X86_IO_APIC */
 
 #define io_apic_assign_pci_irqs 0

arch/x86/include/asm/pgtable.h

@@ -131,8 +131,13 @@ static inline int pte_exec(pte_t pte)
 
 static inline int pte_special(pte_t pte)
 {
-	return (pte_flags(pte) & (_PAGE_PRESENT|_PAGE_SPECIAL)) ==
-				 (_PAGE_PRESENT|_PAGE_SPECIAL);
+	/*
+	 * See CONFIG_NUMA_BALANCING pte_numa in include/asm-generic/pgtable.h.
+	 * On x86 we have _PAGE_BIT_NUMA == _PAGE_BIT_GLOBAL+1 ==
+	 * __PAGE_BIT_SOFTW1 == _PAGE_BIT_SPECIAL.
+	 */
+	return (pte_flags(pte) & _PAGE_SPECIAL) &&
+		(pte_flags(pte) & (_PAGE_PRESENT|_PAGE_PROTNONE));
 }
 
 static inline unsigned long pte_pfn(pte_t pte)

arch/x86/kernel/Makefile

@@ -71,6 +71,7 @@ obj-$(CONFIG_FTRACE_SYSCALLS)	+= ftrace.o
 obj-$(CONFIG_X86_TSC)		+= trace_clock.o
 obj-$(CONFIG_KEXEC)		+= machine_kexec_$(BITS).o
 obj-$(CONFIG_KEXEC)		+= relocate_kernel_$(BITS).o crash.o
+obj-$(CONFIG_KEXEC_FILE)	+= kexec-bzimage64.o
 obj-$(CONFIG_CRASH_DUMP)	+= crash_dump_$(BITS).o
 obj-y				+= kprobes/
 obj-$(CONFIG_MODULES)		+= module.o
@@ -118,5 +119,4 @@ ifeq ($(CONFIG_X86_64),y)
 
 	obj-$(CONFIG_PCI_MMCONFIG)	+= mmconf-fam10h_64.o
 	obj-y				+= vsmp_64.o
-	obj-$(CONFIG_KEXEC)		+= kexec-bzimage64.o
 endif

arch/x86/kernel/apic/io_apic.c

@@ -1070,6 +1070,11 @@ static int mp_map_pin_to_irq(u32 gsi, int idx, int ioapic, int pin,
 	}
 
 	if (flags & IOAPIC_MAP_ALLOC) {
+		/* special handling for legacy IRQs */
+		if (irq < nr_legacy_irqs() && info->count == 1 &&
+		    mp_irqdomain_map(domain, irq, pin) != 0)
+			irq = -1;
+
 		if (irq > 0)
 			info->count++;
 		else if (info->count == 0)
@@ -3896,7 +3901,15 @@ int mp_irqdomain_map(struct irq_domain *domain, unsigned int virq,
 			info->polarity = 1;
 		}
 		info->node = NUMA_NO_NODE;
-		info->set = 1;
+
+		/*
+		 * setup_IO_APIC_irqs() programs all legacy IRQs with default
+		 * trigger and polarity attributes. Don't set the flag for that
+		 * case so the first legacy IRQ user could reprogram the pin
+		 * with real trigger and polarity attributes.
+		 */
+		if (virq >= nr_legacy_irqs() || info->count)
+			info->set = 1;
 	}
 	set_io_apic_irq_attr(&attr, ioapic, hwirq, info->trigger,
 			     info->polarity);
@@ -3946,6 +3959,18 @@ int mp_set_gsi_attr(u32 gsi, int trigger, int polarity, int node)
 	return ret;
 }
 
+bool mp_should_keep_irq(struct device *dev)
+{
+	if (dev->power.is_prepared)
+		return true;
+#ifdef	CONFIG_PM_RUNTIME
+	if (dev->power.runtime_status == RPM_SUSPENDING)
+		return true;
+#endif
+
+	return false;
+}
+
 /* Enable IOAPIC early just for system timer */
 void __init pre_init_apic_IRQ0(void)
 {

arch/x86/kernel/crash.c

@@ -182,8 +182,7 @@ void native_machine_crash_shutdown(struct pt_regs *regs)
 	crash_save_cpu(regs, safe_smp_processor_id());
 }
 
-#ifdef CONFIG_X86_64
-
+#ifdef CONFIG_KEXEC_FILE
 static int get_nr_ram_ranges_callback(unsigned long start_pfn,
 				unsigned long nr_pfn, void *arg)
 {
@@ -696,5 +695,4 @@ int crash_load_segments(struct kimage *image)
 
 	return ret;
 }
-
-#endif /* CONFIG_X86_64 */
+#endif /* CONFIG_KEXEC_FILE */

arch/x86/kernel/irqinit.c

@@ -203,7 +203,7 @@ void __init native_init_IRQ(void)
 		set_intr_gate(i, interrupt[i - FIRST_EXTERNAL_VECTOR]);
 	}
 
-	if (!acpi_ioapic && !of_ioapic)
+	if (!acpi_ioapic && !of_ioapic && nr_legacy_irqs())
 		setup_irq(2, &irq2);
 
 #ifdef CONFIG_X86_32

arch/x86/kernel/machine_kexec_64.c

@@ -25,9 +25,11 @@
 #include <asm/debugreg.h>
 #include <asm/kexec-bzimage64.h>
 
+#ifdef CONFIG_KEXEC_FILE
 static struct kexec_file_ops *kexec_file_loaders[] = {
 		&kexec_bzImage64_ops,
 };
+#endif
 
 static void free_transition_pgtable(struct kimage *image)
 {
@@ -178,6 +180,7 @@ static void load_segments(void)
 		);
 }
 
+#ifdef CONFIG_KEXEC_FILE
 /* Update purgatory as needed after various image segments have been prepared */
 static int arch_update_purgatory(struct kimage *image)
 {
@@ -209,6 +212,12 @@ static int arch_update_purgatory(struct kimage *image)
 
 	return ret;
 }
+#else /* !CONFIG_KEXEC_FILE */
+static inline int arch_update_purgatory(struct kimage *image)
+{
+	return 0;
+}
+#endif /* CONFIG_KEXEC_FILE */
 
 int machine_kexec_prepare(struct kimage *image)
 {
@@ -329,6 +338,7 @@ void arch_crash_save_vmcoreinfo(void)
 
 /* arch-dependent functionality related to kexec file-based syscall */
 
+#ifdef CONFIG_KEXEC_FILE
 int arch_kexec_kernel_image_probe(struct kimage *image, void *buf,
 				  unsigned long buf_len)
 {
@@ -522,3 +532,4 @@ overflow:
 	       (int)ELF64_R_TYPE(rel[i].r_info), value);
 	return -ENOEXEC;
 }
+#endif /* CONFIG_KEXEC_FILE */

arch/x86/kernel/time.c

@@ -68,6 +68,8 @@ static struct irqaction irq0  = {
 
 void __init setup_default_timer_irq(void)
 {
+	if (!nr_legacy_irqs())
+		return;
 	setup_irq(0, &irq0);
 }
 

arch/x86/pci/intel_mid_pci.c

@@ -229,7 +229,7 @@ static int intel_mid_pci_irq_enable(struct pci_dev *dev)
 
 static void intel_mid_pci_irq_disable(struct pci_dev *dev)
 {
-	if (!dev->dev.power.is_prepared && dev->irq > 0)
+	if (!mp_should_keep_irq(&dev->dev) && dev->irq > 0)
 		mp_unmap_irq(dev->irq);
 }
 

arch/x86/pci/irq.c

@@ -1256,7 +1256,7 @@ static int pirq_enable_irq(struct pci_dev *dev)
 
 static void pirq_disable_irq(struct pci_dev *dev)
 {
-	if (io_apic_assign_pci_irqs && !dev->dev.power.is_prepared &&
+	if (io_apic_assign_pci_irqs && !mp_should_keep_irq(&dev->dev) &&
 	    dev->irq) {
 		mp_unmap_irq(dev->irq);
 		dev->irq = 0;

arch/x86/purgatory/Makefile

@@ -11,6 +11,7 @@ targets += purgatory.ro
 # sure how to relocate those. Like kexec-tools, use custom flags.
 
 KBUILD_CFLAGS := -fno-strict-aliasing -Wall -Wstrict-prototypes -fno-zero-initialized-in-bss -fno-builtin -ffreestanding -c -MD -Os -mcmodel=large
+KBUILD_CFLAGS += -m$(BITS)
 
 $(obj)/purgatory.ro: $(PURGATORY_OBJS) FORCE
 		$(call if_changed,ld)
@@ -24,7 +25,4 @@ $(obj)/kexec-purgatory.c: $(obj)/purgatory.ro FORCE
 	$(call if_changed,bin2c)
 
 
-# No loaders for 32bits yet.
-ifeq ($(CONFIG_X86_64),y)
- obj-$(CONFIG_KEXEC)		+= kexec-purgatory.o
-endif
+obj-$(CONFIG_KEXEC_FILE)	+= kexec-purgatory.o

arch/xtensa/Kconfig

@@ -4,24 +4,23 @@ config ZONE_DMA
 config XTENSA
 	def_bool y
 	select ARCH_WANT_FRAME_POINTERS
-	select HAVE_IDE
-	select GENERIC_ATOMIC64
-	select GENERIC_CLOCKEVENTS
-	select VIRT_TO_BUS
-	select GENERIC_IRQ_SHOW
-	select GENERIC_SCHED_CLOCK
-	select MODULES_USE_ELF_RELA
-	select GENERIC_PCI_IOMAP
 	select ARCH_WANT_IPC_PARSE_VERSION
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select BUILDTIME_EXTABLE_SORT
 	select CLONE_BACKWARDS
-	select IRQ_DOMAIN
-	select HAVE_OPROFILE
+	select COMMON_CLK
+	select GENERIC_ATOMIC64
+	select GENERIC_CLOCKEVENTS
+	select GENERIC_IRQ_SHOW
+	select GENERIC_PCI_IOMAP
+	select GENERIC_SCHED_CLOCK
 	select HAVE_FUNCTION_TRACER
 	select HAVE_IRQ_TIME_ACCOUNTING
+	select HAVE_OPROFILE
 	select HAVE_PERF_EVENTS
-	select COMMON_CLK
+	select IRQ_DOMAIN
+	select MODULES_USE_ELF_RELA
+	select VIRT_TO_BUS
 	help
 	  Xtensa processors are 32-bit RISC machines designed by Tensilica
 	  primarily for embedded systems.  These processors are both
@@ -62,7 +61,9 @@ config TRACE_IRQFLAGS_SUPPORT
 	def_bool y
 
 config MMU
-	def_bool n
+	bool
+	default n if !XTENSA_VARIANT_CUSTOM
+	default XTENSA_VARIANT_MMU if XTENSA_VARIANT_CUSTOM
 
 config VARIANT_IRQ_SWITCH
 	def_bool n
@@ -102,8 +103,40 @@ config XTENSA_VARIANT_S6000
 	select VARIANT_IRQ_SWITCH
 	select ARCH_REQUIRE_GPIOLIB
 	select XTENSA_CALIBRATE_CCOUNT
+
+config XTENSA_VARIANT_CUSTOM
+	bool "Custom Xtensa processor configuration"
+	select MAY_HAVE_SMP
+	select HAVE_XTENSA_GPIO32
+	help
+	  Select this variant to use a custom Xtensa processor configuration.
+	  You will be prompted for a processor variant CORENAME.
 endchoice
 
+config XTENSA_VARIANT_CUSTOM_NAME
+	string "Xtensa Processor Custom Core Variant Name"
+	depends on XTENSA_VARIANT_CUSTOM
+	help
+	  Provide the name of a custom Xtensa processor variant.
+	  This CORENAME selects arch/xtensa/variant/CORENAME.
+	  Dont forget you have to select MMU if you have one.
+
+config XTENSA_VARIANT_NAME
+	string
+	default "dc232b"			if XTENSA_VARIANT_DC232B
+	default "dc233c"			if XTENSA_VARIANT_DC233C
+	default "fsf"				if XTENSA_VARIANT_FSF
+	default "s6000"				if XTENSA_VARIANT_S6000
+	default XTENSA_VARIANT_CUSTOM_NAME	if XTENSA_VARIANT_CUSTOM
+
+config XTENSA_VARIANT_MMU
+	bool "Core variant has a Full MMU (TLB, Pages, Protection, etc)"
+	depends on XTENSA_VARIANT_CUSTOM
+	default y
+	help
+	  Build a Conventional Kernel with full MMU support,
+	  ie: it supports a TLB with auto-loading, page protection.
+
 config XTENSA_UNALIGNED_USER
 	bool "Unaligned memory access in use space"
 	help
@@ -156,13 +189,9 @@ config HOTPLUG_CPU
 
 	  Say N if you want to disable CPU hotplug.
 
-config MATH_EMULATION
-	bool "Math emulation"
-	help
-	Can we use information of configuration file?
-
 config INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
 	bool "Initialize Xtensa MMU inside the Linux kernel code"
+	depends on MMU
 	default y
 	help
 	  Earlier version initialized the MMU in the exception vector
@@ -192,6 +221,7 @@ config INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
 
 config HIGHMEM
 	bool "High Memory Support"
+	depends on MMU
 	help
 	  Linux can use the full amount of RAM in the system by
 	  default. However, the default MMUv2 setup only maps the
@@ -208,6 +238,32 @@ config HIGHMEM
 
 	  If unsure, say Y.
 
+config FAST_SYSCALL_XTENSA
+	bool "Enable fast atomic syscalls"
+	default n
+	help
+	  fast_syscall_xtensa is a syscall that can make atomic operations
+	  on UP kernel when processor has no s32c1i support.
+
+	  This syscall is deprecated. It may have issues when called with
+	  invalid arguments. It is provided only for backwards compatibility.
+	  Only enable it if your userspace software requires it.
+
+	  If unsure, say N.
+
+config FAST_SYSCALL_SPILL_REGISTERS
+	bool "Enable spill registers syscall"
+	default n
+	help
+	  fast_syscall_spill_registers is a syscall that spills all active
+	  register windows of a calling userspace task onto its stack.
+
+	  This syscall is deprecated. It may have issues when called with
+	  invalid arguments. It is provided only for backwards compatibility.
+	  Only enable it if your userspace software requires it.
+
+	  If unsure, say N.
+
 endmenu
 
 config XTENSA_CALIBRATE_CCOUNT
@@ -250,12 +306,14 @@ config XTENSA_PLATFORM_ISS
 
 config XTENSA_PLATFORM_XT2000
 	bool "XT2000"
+	select HAVE_IDE
 	help
 	  XT2000 is the name of Tensilica's feature-rich emulation platform.
 	  This hardware is capable of running a full Linux distribution.
 
 config XTENSA_PLATFORM_S6105
 	bool "S6105"
+	select HAVE_IDE
 	select SERIAL_CONSOLE
 	select NO_IOPORT_MAP
 

arch/xtensa/Makefile

@@ -4,6 +4,7 @@
 # for more details.
 #
 # Copyright (C) 2001 - 2005  Tensilica Inc.
+# Copyright (C) 2014 Cadence Design Systems Inc.
 #
 # This file is included by the global makefile so that you can add your own
 # architecture-specific flags and dependencies. Remember to do have actions
@@ -13,11 +14,7 @@
 # Core configuration.
 # (Use VAR=<xtensa_config> to use another default compiler.)
 
-variant-$(CONFIG_XTENSA_VARIANT_FSF)		:= fsf
-variant-$(CONFIG_XTENSA_VARIANT_DC232B)		:= dc232b
-variant-$(CONFIG_XTENSA_VARIANT_DC233C)		:= dc233c
-variant-$(CONFIG_XTENSA_VARIANT_S6000)		:= s6000
-variant-$(CONFIG_XTENSA_VARIANT_LINUX_CUSTOM)	:= custom
+variant-y := $(patsubst "%",%,$(CONFIG_XTENSA_VARIANT_NAME))
 
 VARIANT = $(variant-y)
 export VARIANT

arch/xtensa/boot/dts/kc705.dts

@@ -4,8 +4,11 @@
 
 / {
 	compatible = "cdns,xtensa-kc705";
+	chosen {
+		bootargs = "earlycon=uart8250,mmio32,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug memmap=0x38000000";
+	};
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000>;
+		reg = <0x00000000 0x38000000>;
 	};
 };