pktgen: add sample script pktgen_sample02_multiqueue.sh

Add the pktgen samples script pktgen_sample02_multiqueue.sh that
demonstrates generating packets on multiqueue NICs.

Specifically notice the options "-t" that specifies how many
kernel threads to activate.  Also notice the flag QUEUE_MAP_CPU,
which cause the SKB TX queue to be mapped to the CPU running the
kernel thread.  For best scalability people are also encourage to
map NIC IRQ /proc/irq/*/smp_affinity to CPU number.

Usage example with "-t" 4 threads and help:
 ./pktgen_sample02_multiqueue.sh -i eth4 -m 00:1B:21:3C:9D:F8 -t 4

Usage: ./pktgen_sample02_multiqueue.sh [-vx] -i ethX
  -i : ($DEV)       output interface/device (required)
  -s : ($PKT_SIZE)  packet size
  -d : ($DEST_IP)   destination IP
  -m : ($DST_MAC)   destination MAC-addr
  -t : ($THREADS)   threads to start
  -c : ($SKB_CLONE) SKB clones send before alloc new SKB
  -b : ($BURST)     HW level bursting of SKBs
  -v : ($VERBOSE)   verbose
  -x : ($DEBUG)     debug

Removing pktgen.conf-2-1 and pktgen.conf-2-2 as these examples
should be covered now.

Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/networking/pktgen.txt

@@ -244,8 +244,6 @@ pktgen_sampleXX scripts and modify them to fit your own needs.
 The old scripts:
 
 pktgen.conf-1-2                  # 1 CPU 2 dev
-pktgen.conf-2-1                  # 2 CPU's 1 dev 
-pktgen.conf-2-2                  # 2 CPU's 2 dev
 pktgen.conf-1-1-rdos             # 1 CPU 1 dev w. route DoS 
 pktgen.conf-1-1-ip6              # 1 CPU 1 dev ipv6
 pktgen.conf-1-1-ip6-rdos         # 1 CPU 1 dev ipv6  w. route DoS

samples/pktgen/pktgen.conf-2-1

@@ -1,66 +0,0 @@
-#!/bin/bash
-
-#modprobe pktgen
-
-
-function pgset() {
-    local result
-
-    echo $1 > $PGDEV
-
-    result=`cat $PGDEV | fgrep "Result: OK:"`
-    if [ "$result" = "" ]; then
-         cat $PGDEV | fgrep Result:
-    fi
-}
-
-# Config Start Here -----------------------------------------------------------
-
-
-# thread config
-# Each CPU has its own thread. Two CPU example. We add eth1 to the first
-# and leave the second idle.
-
-PGDEV=/proc/net/pktgen/kpktgend_0
-  echo "Removing all devices"
- pgset "rem_device_all"
-  echo "Adding eth1"
- pgset "add_device eth1"
-
-# We need to remove old config since we dont use this thread. We can only
-# one NIC on one CPU due to affinity reasons.
-
-PGDEV=/proc/net/pktgen/kpktgend_1
-  echo "Removing all devices"
- pgset "rem_device_all"
-
-# device config
-# delay 0 means maximum speed.
-
-CLONE_SKB="clone_skb 1000000"
-# NIC adds 4 bytes CRC
-PKT_SIZE="pkt_size 60"
-
-# COUNT 0 means forever
-#COUNT="count 0"
-COUNT="count 10000000"
-DELAY="delay 0"
-
-PGDEV=/proc/net/pktgen/eth1
-  echo "Configuring $PGDEV"
- pgset "$COUNT"
- pgset "$CLONE_SKB"
- pgset "$PKT_SIZE"
- pgset "$DELAY"
- pgset "dst 10.10.11.2"
- pgset "dst_mac  00:04:23:08:91:dc"
-
-
-# Time to run
-PGDEV=/proc/net/pktgen/pgctrl
-
- echo "Running... ctrl^C to stop"
- trap true INT
- pgset "start"
- echo "Done"
- cat /proc/net/pktgen/eth1

samples/pktgen/pktgen.conf-2-2

@@ -1,73 +0,0 @@
-#!/bin/bash
-
-#modprobe pktgen
-
-
-function pgset() {
-    local result
-
-    echo $1 > $PGDEV
-
-    result=`cat $PGDEV | fgrep "Result: OK:"`
-    if [ "$result" = "" ]; then
-         cat $PGDEV | fgrep Result:
-    fi
-}
-
-# Config Start Here -----------------------------------------------------------
-
-
-# thread config
-# Each CPU has its own thread. Two CPU example. We add eth1, eth2 respectively.
-
-PGDEV=/proc/net/pktgen/kpktgend_0
-  echo "Removing all devices"
- pgset "rem_device_all"
-  echo "Adding eth1"
- pgset "add_device eth1"
-
-PGDEV=/proc/net/pktgen/kpktgend_1
-  echo "Removing all devices"
- pgset "rem_device_all"
-  echo "Adding eth2"
- pgset "add_device eth2"
-
-
-# device config
-# delay 0 means maximum speed.
-
-CLONE_SKB="clone_skb 1000000"
-# NIC adds 4 bytes CRC
-PKT_SIZE="pkt_size 60"
-
-# COUNT 0 means forever
-#COUNT="count 0"
-COUNT="count 10000000"
-DELAY="delay 0"
-
-PGDEV=/proc/net/pktgen/eth1
-  echo "Configuring $PGDEV"
- pgset "$COUNT"
- pgset "$CLONE_SKB"
- pgset "$PKT_SIZE"
- pgset "$DELAY"
- pgset "dst 10.10.11.2"
- pgset "dst_mac  00:04:23:08:91:dc"
-
-PGDEV=/proc/net/pktgen/eth2
-  echo "Configuring $PGDEV"
- pgset "$COUNT"
- pgset "$CLONE_SKB"
- pgset "$PKT_SIZE"
- pgset "$DELAY"
- pgset "dst 192.168.2.2"
- pgset "dst_mac  00:04:23:08:91:de"
-
-# Time to run
-PGDEV=/proc/net/pktgen/pgctrl
-
- echo "Running... ctrl^C to stop"
- trap true INT
- pgset "start"
- echo "Done"
- cat /proc/net/pktgen/eth1 /proc/net/pktgen/eth2

samples/pktgen/pktgen_sample02_multiqueue.sh

@@ -0,0 +1,75 @@
+#!/bin/bash
+#
+# Multiqueue: Using pktgen threads for sending on multiple CPUs
+#  * adding devices to kernel threads
+#  * notice the naming scheme for keeping device names unique
+#  * nameing scheme: dev@thread_number
+#  * flow variation via random UDP source port
+#
+basedir=`dirname $0`
+source ${basedir}/functions.sh
+root_check_run_with_sudo "$@"
+#
+# Required param: -i dev in $DEV
+source ${basedir}/parameters.sh
+
+# Base Config
+DELAY="0"        # Zero means max speed
+COUNT="100000"   # Zero means indefinitely
+[ -z "$CLONE_SKB" ] && CLONE_SKB="0"
+
+# Flow variation random source port between min and max
+UDP_MIN=9
+UDP_MAX=109
+
+# (example of setting default params in your script)
+[ -z "$DEST_IP" ] && DEST_IP="198.18.0.42"
+[ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff"
+
+# General cleanup everything since last run
+pg_ctrl "reset"
+
+# Threads are specified with parameter -t value in $THREADS
+for ((thread = 0; thread < $THREADS; thread++)); do
+    # The device name is extended with @name, using thread number to
+    # make then unique, but any name will do.
+    dev=${DEV}@${thread}
+
+    # Add remove all other devices and add_device $dev to thread
+    pg_thread $thread "rem_device_all"
+    pg_thread $thread "add_device" $dev
+
+    # Notice config queue to map to cpu (mirrors smp_processor_id())
+    # It is beneficial to map IRQ /proc/irq/*/smp_affinity 1:1 to CPU number
+    pg_set $dev "flag QUEUE_MAP_CPU"
+
+    # Base config of dev
+    pg_set $dev "count $COUNT"
+    pg_set $dev "clone_skb $CLONE_SKB"
+    pg_set $dev "pkt_size $PKT_SIZE"
+    pg_set $dev "delay $DELAY"
+
+    # Flag example disabling timestamping
+    pg_set $dev "flag NO_TIMESTAMP"
+
+    # Destination
+    pg_set $dev "dst_mac $DST_MAC"
+    pg_set $dev "dst $DEST_IP"
+
+    # Setup random UDP port src range
+    pg_set $dev "flag UDPSRC_RND"
+    pg_set $dev "udp_src_min $UDP_MIN"
+    pg_set $dev "udp_src_max $UDP_MAX"
+done
+
+# start_run
+echo "Running... ctrl^C to stop" >&2
+pg_ctrl "start"
+echo "Done" >&2
+
+# Print results
+for ((thread = 0; thread < $THREADS; thread++)); do
+    dev=${DEV}@${thread}
+    echo "Device: $dev"
+    cat /proc/net/pktgen/$dev | grep -A2 "Result:"
+done