pinctrl: meson: separate soc drivers

When meson pinctrl is enabled, all meson platforms pinctrl drivers are
built in the kernel, with a significant amount of data.

This leads to situation where pinctrl drivers targeting an architecture
are also compiled and shipped on another one (ex: meson8 - ARM - compiled
and shipped on ARM64 builds). This is a waste of memory we can easily
avoid.

This change makes 4 pinctrl drivers (1 per SoC) out the original single
driver, allowing to compile and ship only the ones required.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

drivers/pinctrl/Kconfig

@@ -167,16 +167,6 @@ config PINCTRL_MCP23S08
 	  This provides a GPIO interface supporting inputs and outputs.
 	  The I2C versions of the chips can be used as interrupt-controller.
 
-config PINCTRL_MESON
-	bool
-	depends on OF
-	select PINMUX
-	select PINCONF
-	select GENERIC_PINCONF
-	select GPIOLIB
-	select OF_GPIO
-	select REGMAP_MMIO
-
 config PINCTRL_OXNAS
 	bool
 	depends on OF
@@ -369,6 +359,7 @@ source "drivers/pinctrl/uniphier/Kconfig"
 source "drivers/pinctrl/vt8500/Kconfig"
 source "drivers/pinctrl/mediatek/Kconfig"
 source "drivers/pinctrl/zte/Kconfig"
+source "drivers/pinctrl/meson/Kconfig"
 
 config PINCTRL_XWAY
 	bool

drivers/pinctrl/meson/Kconfig

@@ -0,0 +1,34 @@
+menuconfig PINCTRL_MESON
+	bool "Amlogic SoC pinctrl drivers"
+	depends on ARCH_MESON
+	depends on OF
+	select PINMUX
+	select PINCONF
+	select GENERIC_PINCONF
+	select GPIOLIB
+	select OF_GPIO
+	select REGMAP_MMIO
+
+if PINCTRL_MESON
+
+config PINCTRL_MESON8
+	bool "Meson 8 SoC pinctrl driver"
+	depends on ARM
+	default y
+
+config PINCTRL_MESON8B
+	bool "Meson 8b SoC pinctrl driver"
+	depends on ARM
+	default y
+
+config PINCTRL_MESON_GXBB
+	bool "Meson gxbb SoC pinctrl driver"
+	depends on ARM64
+	default y
+
+config PINCTRL_MESON_GXL
+	bool "Meson gxl SoC pinctrl driver"
+	depends on ARM64
+	default y
+
+endif

drivers/pinctrl/meson/Makefile

@@ -1,3 +1,5 @@
-obj-y	+= pinctrl-meson8.o pinctrl-meson8b.o
-obj-y	+= pinctrl-meson-gxbb.o pinctrl-meson-gxl.o
-obj-y	+= pinctrl-meson.o
+obj-$(CONFIG_PINCTRL_MESON) += pinctrl-meson.o
+obj-$(CONFIG_PINCTRL_MESON8) += pinctrl-meson8.o
+obj-$(CONFIG_PINCTRL_MESON8B) += pinctrl-meson8b.o
+obj-$(CONFIG_PINCTRL_MESON_GXBB) += pinctrl-meson-gxbb.o
+obj-$(CONFIG_PINCTRL_MESON_GXL) += pinctrl-meson-gxl.o

drivers/pinctrl/meson/pinctrl-meson-gxbb.c

@@ -824,7 +824,7 @@ static struct meson_bank meson_gxbb_aobus_banks[] = {
 	BANK("AO",   GPIOAO_0,  GPIOAO_13, 0, 13, 0,  0,  0, 16,  0,  0,  0, 16,  1,  0),
 };
 
-struct meson_pinctrl_data meson_gxbb_periphs_pinctrl_data = {
+static struct meson_pinctrl_data meson_gxbb_periphs_pinctrl_data = {
 	.name		= "periphs-banks",
 	.pins		= meson_gxbb_periphs_pins,
 	.groups		= meson_gxbb_periphs_groups,
@@ -836,7 +836,7 @@ struct meson_pinctrl_data meson_gxbb_periphs_pinctrl_data = {
 	.num_banks	= ARRAY_SIZE(meson_gxbb_periphs_banks),
 };
 
-struct meson_pinctrl_data meson_gxbb_aobus_pinctrl_data = {
+static struct meson_pinctrl_data meson_gxbb_aobus_pinctrl_data = {
 	.name		= "aobus-banks",
 	.pins		= meson_gxbb_aobus_pins,
 	.groups		= meson_gxbb_aobus_groups,
@@ -847,3 +847,24 @@ struct meson_pinctrl_data meson_gxbb_aobus_pinctrl_data = {
 	.num_funcs	= ARRAY_SIZE(meson_gxbb_aobus_functions),
 	.num_banks	= ARRAY_SIZE(meson_gxbb_aobus_banks),
 };
+
+static const struct of_device_id meson_gxbb_pinctrl_dt_match[] = {
+	{
+		.compatible = "amlogic,meson-gxbb-periphs-pinctrl",
+		.data = &meson_gxbb_periphs_pinctrl_data,
+	},
+	{
+		.compatible = "amlogic,meson-gxbb-aobus-pinctrl",
+		.data = &meson_gxbb_aobus_pinctrl_data,
+	},
+	{ },
+};
+
+static struct platform_driver meson_gxbb_pinctrl_driver = {
+	.probe		= meson_pinctrl_probe,
+	.driver = {
+		.name	= "meson-gxbb-pinctrl",
+		.of_match_table = meson_gxbb_pinctrl_dt_match,
+	},
+};
+builtin_platform_driver(meson_gxbb_pinctrl_driver);

drivers/pinctrl/meson/pinctrl-meson-gxl.c

@@ -809,7 +809,7 @@ static struct meson_bank meson_gxl_aobus_banks[] = {
 	BANK("AO",   GPIOAO_0,  GPIOAO_9, 0, 9, 0,  0,  0, 16,  0,  0,  0, 16,  1,  0),
 };
 
-struct meson_pinctrl_data meson_gxl_periphs_pinctrl_data = {
+static struct meson_pinctrl_data meson_gxl_periphs_pinctrl_data = {
 	.name		= "periphs-banks",
 	.pins		= meson_gxl_periphs_pins,
 	.groups		= meson_gxl_periphs_groups,
@@ -821,7 +821,7 @@ struct meson_pinctrl_data meson_gxl_periphs_pinctrl_data = {
 	.num_banks	= ARRAY_SIZE(meson_gxl_periphs_banks),
 };
 
-struct meson_pinctrl_data meson_gxl_aobus_pinctrl_data = {
+static struct meson_pinctrl_data meson_gxl_aobus_pinctrl_data = {
 	.name		= "aobus-banks",
 	.pins		= meson_gxl_aobus_pins,
 	.groups		= meson_gxl_aobus_groups,
@@ -832,3 +832,24 @@ struct meson_pinctrl_data meson_gxl_aobus_pinctrl_data = {
 	.num_funcs	= ARRAY_SIZE(meson_gxl_aobus_functions),
 	.num_banks	= ARRAY_SIZE(meson_gxl_aobus_banks),
 };
+
+static const struct of_device_id meson_gxl_pinctrl_dt_match[] = {
+	{
+		.compatible = "amlogic,meson-gxl-periphs-pinctrl",
+		.data = &meson_gxl_periphs_pinctrl_data,
+	},
+	{
+		.compatible = "amlogic,meson-gxl-aobus-pinctrl",
+		.data = &meson_gxl_aobus_pinctrl_data,
+	},
+	{ },
+};
+
+static struct platform_driver meson_gxl_pinctrl_driver = {
+	.probe		= meson_pinctrl_probe,
+	.driver = {
+		.name	= "meson-gxl-pinctrl",
+		.of_match_table = meson_gxl_pinctrl_dt_match,
+	},
+};
+builtin_platform_driver(meson_gxl_pinctrl_driver);

drivers/pinctrl/meson/pinctrl-meson.c

@@ -50,6 +50,7 @@
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/pinctrl/pinconf-generic.h>
 #include <linux/pinctrl/pinconf.h>
 #include <linux/pinctrl/pinctrl.h>
@@ -481,42 +482,6 @@ static int meson_gpio_get(struct gpio_chip *chip, unsigned gpio)
 	return !!(val & BIT(bit));
 }
 
-static const struct of_device_id meson_pinctrl_dt_match[] = {
-	{
-		.compatible = "amlogic,meson8-cbus-pinctrl",
-		.data = &meson8_cbus_pinctrl_data,
-	},
-	{
-		.compatible = "amlogic,meson8b-cbus-pinctrl",
-		.data = &meson8b_cbus_pinctrl_data,
-	},
-	{
-		.compatible = "amlogic,meson8-aobus-pinctrl",
-		.data = &meson8_aobus_pinctrl_data,
-	},
-	{
-		.compatible = "amlogic,meson8b-aobus-pinctrl",
-		.data = &meson8b_aobus_pinctrl_data,
-	},
-	{
-		.compatible = "amlogic,meson-gxbb-periphs-pinctrl",
-		.data = &meson_gxbb_periphs_pinctrl_data,
-	},
-	{
-		.compatible = "amlogic,meson-gxbb-aobus-pinctrl",
-		.data = &meson_gxbb_aobus_pinctrl_data,
-	},
-	{
-		.compatible = "amlogic,meson-gxl-periphs-pinctrl",
-		.data = &meson_gxl_periphs_pinctrl_data,
-	},
-	{
-		.compatible = "amlogic,meson-gxl-aobus-pinctrl",
-		.data = &meson_gxl_aobus_pinctrl_data,
-	},
-	{ },
-};
-
 static int meson_gpiolib_register(struct meson_pinctrl *pc)
 {
 	int ret;
@@ -624,9 +589,8 @@ static int meson_pinctrl_parse_dt(struct meson_pinctrl *pc,
 	return 0;
 }
 
-static int meson_pinctrl_probe(struct platform_device *pdev)
+int meson_pinctrl_probe(struct platform_device *pdev)
 {
-	const struct of_device_id *match;
 	struct device *dev = &pdev->dev;
 	struct meson_pinctrl *pc;
 	int ret;
@@ -636,10 +600,9 @@ static int meson_pinctrl_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	pc->dev = dev;
-	match = of_match_node(meson_pinctrl_dt_match, pdev->dev.of_node);
-	pc->data = (struct meson_pinctrl_data *) match->data;
+	pc->data = (struct meson_pinctrl_data *) of_device_get_match_data(dev);
 
-	ret = meson_pinctrl_parse_dt(pc, pdev->dev.of_node);
+	ret = meson_pinctrl_parse_dt(pc, dev->of_node);
 	if (ret)
 		return ret;
 
@@ -659,12 +622,3 @@ static int meson_pinctrl_probe(struct platform_device *pdev)
 
 	return meson_gpiolib_register(pc);
 }
-
-static struct platform_driver meson_pinctrl_driver = {
-	.probe		= meson_pinctrl_probe,
-	.driver = {
-		.name	= "meson-pinctrl",
-		.of_match_table = meson_pinctrl_dt_match,
-	},
-};
-builtin_platform_driver(meson_pinctrl_driver);

drivers/pinctrl/meson/pinctrl-meson.h

@@ -13,6 +13,7 @@
 
 #include <linux/gpio.h>
 #include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/types.h>
 
@@ -165,11 +166,5 @@ struct meson_pinctrl {
 
 #define MESON_PIN(x) PINCTRL_PIN(x, #x)
 
-extern struct meson_pinctrl_data meson8_cbus_pinctrl_data;
-extern struct meson_pinctrl_data meson8_aobus_pinctrl_data;
-extern struct meson_pinctrl_data meson8b_cbus_pinctrl_data;
-extern struct meson_pinctrl_data meson8b_aobus_pinctrl_data;
-extern struct meson_pinctrl_data meson_gxbb_periphs_pinctrl_data;
-extern struct meson_pinctrl_data meson_gxbb_aobus_pinctrl_data;
-extern struct meson_pinctrl_data meson_gxl_periphs_pinctrl_data;
-extern struct meson_pinctrl_data meson_gxl_aobus_pinctrl_data;
+/* Common probe function */
+int meson_pinctrl_probe(struct platform_device *pdev);

drivers/pinctrl/meson/pinctrl-meson8.c

@@ -1044,7 +1044,7 @@ static struct meson_bank meson8_aobus_banks[] = {
 	BANK("AO",   GPIOAO_0, GPIO_TEST_N, 0, 13, 0,  0,  0, 16,  0,  0,  0, 16,  1,  0),
 };
 
-struct meson_pinctrl_data meson8_cbus_pinctrl_data = {
+static struct meson_pinctrl_data meson8_cbus_pinctrl_data = {
 	.name		= "cbus-banks",
 	.pins		= meson8_cbus_pins,
 	.groups		= meson8_cbus_groups,
@@ -1056,7 +1056,7 @@ struct meson_pinctrl_data meson8_cbus_pinctrl_data = {
 	.num_banks	= ARRAY_SIZE(meson8_cbus_banks),
 };
 
-struct meson_pinctrl_data meson8_aobus_pinctrl_data = {
+static struct meson_pinctrl_data meson8_aobus_pinctrl_data = {
 	.name		= "ao-bank",
 	.pins		= meson8_aobus_pins,
 	.groups		= meson8_aobus_groups,
@@ -1067,3 +1067,24 @@ struct meson_pinctrl_data meson8_aobus_pinctrl_data = {
 	.num_funcs	= ARRAY_SIZE(meson8_aobus_functions),
 	.num_banks	= ARRAY_SIZE(meson8_aobus_banks),
 };
+
+static const struct of_device_id meson8_pinctrl_dt_match[] = {
+	{
+		.compatible = "amlogic,meson8-cbus-pinctrl",
+		.data = &meson8_cbus_pinctrl_data,
+	},
+	{
+		.compatible = "amlogic,meson8-aobus-pinctrl",
+		.data = &meson8_aobus_pinctrl_data,
+	},
+	{ },
+};
+
+static struct platform_driver meson8_pinctrl_driver = {
+	.probe		= meson_pinctrl_probe,
+	.driver = {
+		.name	= "meson8-pinctrl",
+		.of_match_table = meson8_pinctrl_dt_match,
+	},
+};
+builtin_platform_driver(meson8_pinctrl_driver);

drivers/pinctrl/meson/pinctrl-meson8b.c

@@ -904,7 +904,7 @@ static struct meson_bank meson8b_aobus_banks[] = {
 	BANK("AO",   GPIOAO_0, GPIO_TEST_N, 0, 13, 0,  0,  0, 16,  0,  0,  0, 16,  1,  0),
 };
 
-struct meson_pinctrl_data meson8b_cbus_pinctrl_data = {
+static struct meson_pinctrl_data meson8b_cbus_pinctrl_data = {
 	.name		= "cbus-banks",
 	.pins		= meson8b_cbus_pins,
 	.groups		= meson8b_cbus_groups,
@@ -916,7 +916,7 @@ struct meson_pinctrl_data meson8b_cbus_pinctrl_data = {
 	.num_banks	= ARRAY_SIZE(meson8b_cbus_banks),
 };
 
-struct meson_pinctrl_data meson8b_aobus_pinctrl_data = {
+static struct meson_pinctrl_data meson8b_aobus_pinctrl_data = {
 	.name		= "aobus-banks",
 	.pins		= meson8b_aobus_pins,
 	.groups		= meson8b_aobus_groups,
@@ -927,3 +927,24 @@ struct meson_pinctrl_data meson8b_aobus_pinctrl_data = {
 	.num_funcs	= ARRAY_SIZE(meson8b_aobus_functions),
 	.num_banks	= ARRAY_SIZE(meson8b_aobus_banks),
 };
+
+static const struct of_device_id meson8b_pinctrl_dt_match[] = {
+	{
+		.compatible = "amlogic,meson8b-cbus-pinctrl",
+		.data = &meson8b_cbus_pinctrl_data,
+	},
+	{
+		.compatible = "amlogic,meson8b-aobus-pinctrl",
+		.data = &meson8b_aobus_pinctrl_data,
+	},
+	{ },
+};
+
+static struct platform_driver meson8b_pinctrl_driver = {
+	.probe		= meson_pinctrl_probe,
+	.driver = {
+		.name	= "meson8b-pinctrl",
+		.of_match_table = meson8b_pinctrl_dt_match,
+	},
+};
+builtin_platform_driver(meson8b_pinctrl_driver);