can: Kconfig: sort drivers alphabetically

Sort the drivers that are directly listed in the Kconfig alphabetically, no
functional change.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

drivers/net/can/Kconfig

@@ -70,13 +70,6 @@ config CAN_AT91
 	  This is a driver for the SoC CAN controller in Atmel's AT91SAM9263
 	  and AT91SAM9X5 processors.
 
-config CAN_TI_HECC
-	depends on ARM
-	tristate "TI High End CAN Controller"
-	---help---
-	  Driver for TI HECC (High End CAN Controller) module found on many
-	  TI devices. The device specifications are available from www.ti.com
-
 config CAN_BFIN
 	depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x
 	tristate "Analog Devices Blackfin on-chip CAN"
@@ -86,30 +79,12 @@ config CAN_BFIN
 	  To compile this driver as a module, choose M here: the
 	  module will be called bfin_can.
 
-config CAN_JANZ_ICAN3
-	tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
-	depends on MFD_JANZ_CMODIO
-	---help---
-	  Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
-	  connects to a MODULbus carrier board.
-
-	  This driver can also be built as a module. If so, the module will be
-	  called janz-ican3.ko.
-
 config CAN_FLEXCAN
 	tristate "Support for Freescale FLEXCAN based chips"
 	depends on ARM || PPC
 	---help---
 	  Say Y here if you want to support for Freescale FlexCAN.
 
-config PCH_CAN
-	tristate "Intel EG20T PCH CAN controller"
-	depends on PCI && (X86_32 || COMPILE_TEST)
-	---help---
-	  This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which
-	  is an IOH for x86 embedded processor (Intel Atom E6xx series).
-	  This driver can access CAN bus.
-
 config CAN_GRCAN
 	tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices"
 	depends on OF && HAS_DMA
@@ -119,6 +94,16 @@ config CAN_GRCAN
 	  endian syntheses of the cores would need some modifications on
 	  the hardware level to work.
 
+config CAN_JANZ_ICAN3
+	tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
+	depends on MFD_JANZ_CMODIO
+	---help---
+	  Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
+	  connects to a MODULbus carrier board.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called janz-ican3.ko.
+
 config CAN_RCAR
 	tristate "Renesas R-Car CAN controller"
 	depends on ARM
@@ -139,6 +124,13 @@ config CAN_SUN4I
 	  To compile this driver as a module, choose M here: the module will
 	  be called sun4i_can.
 
+config CAN_TI_HECC
+	depends on ARM
+	tristate "TI High End CAN Controller"
+	---help---
+	  Driver for TI HECC (High End CAN Controller) module found on many
+	  TI devices. The device specifications are available from www.ti.com
+
 config CAN_XILINXCAN
 	tristate "Xilinx CAN"
 	depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST
@@ -147,6 +139,13 @@ config CAN_XILINXCAN
 	  Xilinx CAN driver. This driver supports both soft AXI CAN IP and
 	  Zynq CANPS IP.
 
+config PCH_CAN
+	tristate "Intel EG20T PCH CAN controller"
+	depends on PCI && (X86_32 || COMPILE_TEST)
+	---help---
+	  This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which
+	  is an IOH for x86 embedded processor (Intel Atom E6xx series).
+	  This driver can access CAN bus.
 
 source "drivers/net/can/c_can/Kconfig"
 source "drivers/net/can/cc770/Kconfig"