Merge branches 'clockevents/4.4-fixes' and 'clockevents/4.5-fixes' of http://git.linaro.org/people/daniel.lezcano/linux into timers/urgent

Pull in fixes from Daniel Lezcano:

 - Fix the vt8500 timer leading to a system lock up when dealing with too
   small delta (Roman Volkov)

 - Select the CLKSRC_MMIO when the fsl_ftm_timer is enabled with COMPILE_TEST
   (Daniel Lezcano)

 - Prevent to compile timers using the 'iomem' API when the architecture has
   not HAS_IOMEM set (Richard Weinberger)

Documentation/arm/keystone/Overview.txt

@@ -49,24 +49,6 @@ specified through DTS. Following are the DTS used:-
 The device tree documentation for the keystone machines are located at
         Documentation/devicetree/bindings/arm/keystone/keystone.txt
 
-Known issues & workaround
--------------------------
-
-Some of the device drivers used on keystone are re-used from that from
-DaVinci and other TI SoCs. These device drivers may use clock APIs directly.
-Some of the keystone specific drivers such as netcp uses run time power
-management API instead to enable clock. As this API has limitations on
-keystone, following workaround is needed to boot Linux.
-
-   Add 'clk_ignore_unused' to the bootargs env variable in u-boot. Otherwise
-   clock frameworks will try to disable clocks that are unused and disable
-   the hardware. This is because netcp related power domain and clock
-   domains are enabled in u-boot as run time power management API currently
-   doesn't enable clocks for netcp due to a limitation. This workaround is
-   expected to be removed in the future when proper API support becomes
-   available. Until then, this work around is needed.
-
-
 Document Author
 ---------------
 Murali Karicheri <m-karicheri2@ti.com>

Documentation/block/null_blk.txt

@@ -70,3 +70,6 @@ use_per_node_hctx=[0/1]: Default: 0
      parameter.
   1: The multi-queue block layer is instantiated with a hardware dispatch
      queue for each CPU node in the system.
+
+use_lightnvm=[0/1]: Default: 0
+  Register device with LightNVM. Requires blk-mq to be used.

Documentation/devicetree/bindings/dma/ti-edma.txt

@@ -22,8 +22,7 @@ Required properties:
 Optional properties:
 - ti,hwmods:	Name of the hwmods associated to the eDMA CC
 - ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow
-		these channels will be SW triggered channels. The list must
-		contain 16 bits numbers, see example.
+		these channels will be SW triggered channels. See example.
 - ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by
 		the driver, they are allocated to be used by for example the
 		DSP. See example.
@@ -56,10 +55,9 @@ edma: edma@49000000 {
 	ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 7>, <&edma_tptc2 0>;
 
 	/* Channel 20 and 21 is allocated for memcpy */
-	ti,edma-memcpy-channels = /bits/ 16 <20 21>;
-	/* The following PaRAM slots are reserved: 35-45 and 100-110 */
-	ti,edma-reserved-slot-ranges = /bits/ 16 <35 10>,
-				       /bits/ 16 <100 10>;
+	ti,edma-memcpy-channels = <20 21>;
+	/* The following PaRAM slots are reserved: 35-44 and 100-109 */
+	ti,edma-reserved-slot-ranges = <35 10>, <100 10>;
 };
 
 edma_tptc0: tptc@49800000 {

Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt

@@ -11,6 +11,10 @@ Required properties:
       0 = active high
       1 = active low
 
+Optional properties:
+- little-endian : GPIO registers are used as little endian. If not
+                  present registers are used as big endian by default.
+
 Example:
 
 gpio0: gpio@1100 {

Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt

@@ -12,7 +12,7 @@ Each key is represented as a sub-node of "allwinner,sun4i-a10-lradc-keys":
 Required subnode-properties:
 	- label: Descriptive name of the key.
 	- linux,code: Keycode to emit.
-	- channel: Channel this key is attached to, mut be 0 or 1.
+	- channel: Channel this key is attached to, must be 0 or 1.
 	- voltage: Voltage in µV at lradc input when this key is pressed.
 
 Example:

Documentation/devicetree/bindings/mtd/partition.txt

@@ -6,7 +6,9 @@ used for what purposes, but which don't use an on-flash partition table such
 as RedBoot.
 
 The partition table should be a subnode of the mtd node and should be named
-'partitions'. Partitions are defined in subnodes of the partitions node.
+'partitions'. This node should have the following property:
+- compatible : (required) must be "fixed-partitions"
+Partitions are then defined in subnodes of the partitions node.
 
 For backwards compatibility partitions as direct subnodes of the mtd device are
 supported. This use is discouraged.
@@ -36,6 +38,7 @@ Examples:
 
 flash@0 {
 	partitions {
+		compatible = "fixed-partitions";
 		#address-cells = <1>;
 		#size-cells = <1>;
 
@@ -53,6 +56,7 @@ flash@0 {
 
 flash@1 {
 	partitions {
+		compatible = "fixed-partitions";
 		#address-cells = <1>;
 		#size-cells = <2>;
 
@@ -66,6 +70,7 @@ flash@1 {
 
 flash@2 {
 	partitions {
+		compatible = "fixed-partitions";
 		#address-cells = <2>;
 		#size-cells = <2>;
 

Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt

@@ -8,6 +8,11 @@ Required properties:
 - phy-mode: See ethernet.txt file in the same directory
 - clocks: a pointer to the reference clock for this device.
 
+Optional properties:
+- tx-csum-limit: maximum mtu supported by port that allow TX checksum.
+  Value is presented in bytes. If not used, by default 1600B is set for
+  "marvell,armada-370-neta" and 9800B for others.
+
 Example:
 
 ethernet@d0070000 {
@@ -15,6 +20,7 @@ ethernet@d0070000 {
 	reg = <0xd0070000 0x2500>;
 	interrupts = <8>;
 	clocks = <&gate_clk 4>;
+	tx-csum-limit = <9800>
 	status = "okay";
 	phy = <&phy0>;
 	phy-mode = "rgmii-id";

Documentation/devicetree/bindings/thermal/rockchip-thermal.txt

@@ -1,7 +1,9 @@
 * Temperature Sensor ADC (TSADC) on rockchip SoCs
 
 Required properties:
-- compatible : "rockchip,rk3288-tsadc"
+- compatible : should be "rockchip,<name>-tsadc"
+   "rockchip,rk3288-tsadc": found on RK3288 SoCs
+   "rockchip,rk3368-tsadc": found on RK3368 SoCs
 - reg : physical base address of the controller and length of memory mapped
 	region.
 - interrupts : The interrupt number to the cpu. The interrupt specifier format

Documentation/networking/e100.txt

@@ -181,17 +181,3 @@ For general information, go to the Intel support website at:
 If an issue is identified with the released source code on the supported
 kernel with a supported adapter, email the specific information related to the
 issue to e1000-devel@lists.sourceforge.net.
-
-
-License
-=======
-
-This software program is released under the terms of a license agreement
-between you ('Licensee') and Intel. Do not use or load this software or any
-associated materials (collectively, the 'Software') until you have carefully
-read the full terms and conditions of the file COPYING located in this software
-package. By loading or using the Software, you agree to the terms of this
-Agreement. If you do not agree with the terms of this Agreement, do not install
-or use the Software.
-
-* Other names and brands may be claimed as the property of others.

MAINTAINERS

@@ -318,7 +318,7 @@ M:	Zhang Rui <rui.zhang@intel.com>
 L:	linux-acpi@vger.kernel.org
 W:	https://01.org/linux-acpi
 S:	Supported
-F:	drivers/acpi/video.c
+F:	drivers/acpi/acpi_video.c
 
 ACPI WMI DRIVER
 L:	platform-driver-x86@vger.kernel.org
@@ -1847,7 +1847,7 @@ S:	Supported
 F:	drivers/net/wireless/ath/ath6kl/
 
 WILOCITY WIL6210 WIRELESS DRIVER
-M:	Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
+M:	Maya Erez <qca_merez@qca.qualcomm.com>
 L:	linux-wireless@vger.kernel.org
 L:	wil6210@qca.qualcomm.com
 S:	Supported
@@ -1931,7 +1931,7 @@ S:	Supported
 F:	drivers/i2c/busses/i2c-at91.c
 
 ATMEL ISI DRIVER
-M:	Josh Wu <josh.wu@atmel.com>
+M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 L:	linux-media@vger.kernel.org
 S:	Supported
 F:	drivers/media/platform/soc_camera/atmel-isi.c
@@ -1950,7 +1950,8 @@ S:	Supported
 F:	drivers/net/ethernet/cadence/
 
 ATMEL NAND DRIVER
-M:	Josh Wu <josh.wu@atmel.com>
+M:	Wenyou Yang <wenyou.yang@atmel.com>
+M:	Josh Wu <rainyfeeling@outlook.com>
 L:	linux-mtd@lists.infradead.org
 S:	Supported
 F:	drivers/mtd/nand/atmel_nand*
@@ -2974,6 +2975,7 @@ F:	kernel/cpuset.c
 CONTROL GROUP - MEMORY RESOURCE CONTROLLER (MEMCG)
 M:	Johannes Weiner <hannes@cmpxchg.org>
 M:	Michal Hocko <mhocko@kernel.org>
+M:	Vladimir Davydov <vdavydov@virtuozzo.com>
 L:	cgroups@vger.kernel.org
 L:	linux-mm@kvack.org
 S:	Maintained
@@ -5576,7 +5578,7 @@ R:	Jesse Brandeburg <jesse.brandeburg@intel.com>
 R:	Shannon Nelson <shannon.nelson@intel.com>
 R:	Carolyn Wyborny <carolyn.wyborny@intel.com>
 R:	Don Skidmore <donald.c.skidmore@intel.com>
-R:	Matthew Vick <matthew.vick@intel.com>
+R:	Bruce Allan <bruce.w.allan@intel.com>
 R:	John Ronciak <john.ronciak@intel.com>
 R:	Mitch Williams <mitch.a.williams@intel.com>
 L:	intel-wired-lan@lists.osuosl.org
@@ -6366,6 +6368,7 @@ F:	arch/*/include/asm/pmem.h
 LIGHTNVM PLATFORM SUPPORT
 M:	Matias Bjorling <mb@lightnvm.io>
 W:	http://github/OpenChannelSSD
+L:	linux-block@vger.kernel.org
 S:	Maintained
 F:	drivers/lightnvm/
 F:	include/linux/lightnvm.h
@@ -8284,7 +8287,7 @@ F:	include/linux/delayacct.h
 F:	kernel/delayacct.c
 
 PERFORMANCE EVENTS SUBSYSTEM
-M:	Peter Zijlstra <a.p.zijlstra@chello.nl>
+M:	Peter Zijlstra <peterz@infradead.org>
 M:	Ingo Molnar <mingo@redhat.com>
 M:	Arnaldo Carvalho de Melo <acme@kernel.org>
 L:	linux-kernel@vger.kernel.org
@@ -8377,6 +8380,14 @@ L:	linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/pinctrl/samsung/
 
+PIN CONTROLLER - SINGLE
+M:	Tony Lindgren <tony@atomide.com>
+M:	Haojian Zhuang <haojian.zhuang@linaro.org>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-omap@vger.kernel.org
+S:	Maintained
+F:	drivers/pinctrl/pinctrl-single.c
+
 PIN CONTROLLER - ST SPEAR
 M:	Viresh Kumar <vireshk@kernel.org>
 L:	spear-devel@list.st.com
@@ -8943,6 +8954,13 @@ F:	drivers/rpmsg/
 F:	Documentation/rpmsg.txt
 F:	include/linux/rpmsg.h
 
+RENESAS ETHERNET DRIVERS
+R:	Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
+L:	netdev@vger.kernel.org
+L:	linux-sh@vger.kernel.org
+F:	drivers/net/ethernet/renesas/
+F:	include/linux/sh_eth.h
+
 RESET CONTROLLER FRAMEWORK
 M:	Philipp Zabel <p.zabel@pengutronix.de>
 S:	Maintained
@@ -9426,8 +9444,10 @@ F:	include/scsi/sg.h
 
 SCSI SUBSYSTEM
 M:	"James E.J. Bottomley" <JBottomley@odin.com>
-L:	linux-scsi@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi.git
+M:	"Martin K. Petersen" <martin.petersen@oracle.com>
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi.git
+L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/
 F:	include/scsi/
@@ -10902,9 +10922,9 @@ S:	Maintained
 F:	drivers/media/tuners/tua9001*
 
 TULIP NETWORK DRIVERS
-M:	Grant Grundler <grundler@parisc-linux.org>
 L:	netdev@vger.kernel.org
-S:	Maintained
+L:	linux-parisc@vger.kernel.org
+S:	Orphan
 F:	drivers/net/ethernet/dec/tulip/
 
 TUN/TAP driver

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 4
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc7
 NAME = Blurry Fish Butt
 
 # *DOCUMENTATION*

arch/arc/Kconfig

@@ -445,6 +445,7 @@ config LINUX_LINK_BASE
 	  However some customers have peripherals mapped at this addr, so
 	  Linux needs to be scooted a bit.
 	  If you don't know what the above means, leave this setting alone.
+	  This needs to match memory start address specified in Device Tree
 
 config HIGHMEM
 	bool "High Memory Support"

arch/arc/Makefile

@@ -81,7 +81,7 @@ endif
 LIBGCC	:= $(shell $(CC) $(cflags-y) --print-libgcc-file-name)
 
 # Modules with short calls might break for calls into builtin-kernel
-KBUILD_CFLAGS_MODULE	+= -mlong-calls
+KBUILD_CFLAGS_MODULE	+= -mlong-calls -mno-millicode
 
 # Finally dump eveything into kernel build system
 KBUILD_CFLAGS	+= $(cflags-y)

arch/arc/boot/dts/axs10x_mb.dtsi

@@ -46,6 +46,7 @@
 			snps,pbl = < 32 >;
 			clocks = <&apbclk>;
 			clock-names = "stmmaceth";
+			max-speed = <100>;
 		};
 
 		ehci@0x40000 {

arch/arc/boot/dts/nsim_hs.dts

@@ -17,7 +17,8 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0x0 0x80000000 0x0 0x40000000	/* 1 GB low mem */
+		/* CONFIG_LINUX_LINK_BASE needs to match low mem start */
+		reg = <0x0 0x80000000 0x0 0x20000000	/* 512 MB low mem */
 		       0x1 0x00000000 0x0 0x40000000>;	/* 1 GB highmem */
 	};
 

arch/arc/configs/axs101_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y

arch/arc/configs/axs103_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y

arch/arc/configs/axs103_smp_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y

arch/arc/configs/nsim_hs_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set

arch/arc/configs/nsim_hs_smp_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set

arch/arc/configs/nsimosci_hs_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set

arch/arc/configs/nsimosci_hs_smp_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y

arch/arc/configs/vdk_hs38_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_CROSS_MEMORY_ATTACH is not set

arch/arc/configs/vdk_hs38_smp_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_CROSS_MEMORY_ATTACH is not set

arch/arc/include/asm/cache.h

@@ -62,9 +62,7 @@ extern int ioc_exists;
 #define ARC_REG_IC_IVIC		0x10
 #define ARC_REG_IC_CTRL		0x11
 #define ARC_REG_IC_IVIL		0x19
-#if defined(CONFIG_ARC_MMU_V3) || defined(CONFIG_ARC_MMU_V4)
 #define ARC_REG_IC_PTAG		0x1E
-#endif
 #define ARC_REG_IC_PTAG_HI	0x1F
 
 /* Bit val in IC_CTRL */

arch/arc/include/asm/irqflags-arcv2.h

@@ -37,6 +37,9 @@
 #define ISA_INIT_STATUS_BITS	(STATUS_IE_MASK | STATUS_AD_MASK | \
 					(ARCV2_IRQ_DEF_PRIO << 1))
 
+/* SLEEP needs default irq priority (<=) which can interrupt the doze */
+#define ISA_SLEEP_ARG		(0x10 | ARCV2_IRQ_DEF_PRIO)
+
 #ifndef __ASSEMBLY__
 
 /*

arch/arc/include/asm/irqflags-compact.h

@@ -43,6 +43,8 @@
 
 #define ISA_INIT_STATUS_BITS	STATUS_IE_MASK
 
+#define ISA_SLEEP_ARG		0x3
+
 #ifndef __ASSEMBLY__
 
 /******************************************************************

arch/arc/include/asm/mach_desc.h

@@ -23,7 +23,7 @@
  * @dt_compat:		Array of device tree 'compatible' strings
  * 			(XXX: although only 1st entry is looked at)
  * @init_early:		Very early callback [called from setup_arch()]
- * @init_cpu_smp:	for each CPU as it is coming up (SMP as well as UP)
+ * @init_per_cpu:	for each CPU as it is coming up (SMP as well as UP)
  * 			[(M):init_IRQ(), (o):start_kernel_secondary()]
  * @init_machine:	arch initcall level callback (e.g. populate static
  * 			platform devices or parse Devicetree)
@@ -35,7 +35,7 @@ struct machine_desc {
 	const char		**dt_compat;
 	void			(*init_early)(void);
 #ifdef CONFIG_SMP
-	void			(*init_cpu_smp)(unsigned int);
+	void			(*init_per_cpu)(unsigned int);
 #endif
 	void			(*init_machine)(void);
 	void			(*init_late)(void);

arch/arc/include/asm/smp.h

@@ -48,7 +48,7 @@ extern int smp_ipi_irq_setup(int cpu, int irq);
  * @init_early_smp:	A SMP specific h/w block can init itself
  * 			Could be common across platforms so not covered by
  * 			mach_desc->init_early()
- * @init_irq_cpu:	Called for each core so SMP h/w block driver can do
+ * @init_per_cpu:	Called for each core so SMP h/w block driver can do
  * 			any needed setup per cpu (e.g. IPI request)
  * @cpu_kick:		For Master to kickstart a cpu (optionally at a PC)
  * @ipi_send:		To send IPI to a @cpu
@@ -57,7 +57,7 @@ extern int smp_ipi_irq_setup(int cpu, int irq);
 struct plat_smp_ops {
 	const char 	*info;
 	void		(*init_early_smp)(void);
-	void		(*init_irq_cpu)(int cpu);
+	void		(*init_per_cpu)(int cpu);
 	void		(*cpu_kick)(int cpu, unsigned long pc);
 	void		(*ipi_send)(int cpu);
 	void		(*ipi_clear)(int irq);

arch/arc/include/asm/unwind.h

@@ -112,7 +112,6 @@ struct unwind_frame_info {
 
 extern int arc_unwind(struct unwind_frame_info *frame);
 extern void arc_unwind_init(void);
-extern void arc_unwind_setup(void);
 extern void *unwind_add_table(struct module *module, const void *table_start,
 			      unsigned long table_size);
 extern void unwind_remove_table(void *handle, int init_only);
@@ -152,9 +151,6 @@ static inline void arc_unwind_init(void)
 {
 }
 
-static inline void arc_unwind_setup(void)
-{
-}
 #define unwind_add_table(a, b, c)
 #define unwind_remove_table(a, b)
 

arch/arc/kernel/ctx_sw.c

@@ -58,8 +58,6 @@ __switch_to(struct task_struct *prev_task, struct task_struct *next_task)
 		"st      sp, [r24]       \n\t"
 #endif
 
-		"sync   \n\t"
-
 		/*
 		 * setup _current_task with incoming tsk.
 		 * optionally, set r25 to that as well

arch/arc/kernel/ctx_sw_asm.S

@@ -44,9 +44,6 @@ __switch_to:
 	* don't need to do anything special to return it
 	*/
 
-	/* hardware memory barrier */
-	sync
-
 	/*
 	 * switch to new task, contained in r1
 	 * Temp reg r3 is required to get the ptr to store val

arch/arc/kernel/intc-arcv2.c

@@ -106,10 +106,21 @@ static struct irq_chip arcv2_irq_chip = {
 static int arcv2_irq_map(struct irq_domain *d, unsigned int irq,
 			 irq_hw_number_t hw)
 {
-	if (irq == TIMER0_IRQ || irq == IPI_IRQ)
+	/*
+	 * core intc IRQs [16, 23]:
+	 * Statically assigned always private-per-core (Timers, WDT, IPI, PCT)
+	 */
+	if (hw < 24) {
+		/*
+		 * A subsequent request_percpu_irq() fails if percpu_devid is
+		 * not set. That in turns sets NOAUTOEN, meaning each core needs
+		 * to call enable_percpu_irq()
+		 */
+		irq_set_percpu_devid(irq);
 		irq_set_chip_and_handler(irq, &arcv2_irq_chip, handle_percpu_irq);
-	else
+	} else {
 		irq_set_chip_and_handler(irq, &arcv2_irq_chip, handle_level_irq);
+	}
 
 	return 0;
 }

arch/arc/kernel/irq.c

@@ -29,11 +29,11 @@ void __init init_IRQ(void)
 
 #ifdef CONFIG_SMP
 	/* a SMP H/w block could do IPI IRQ request here */
-	if (plat_smp_ops.init_irq_cpu)
-		plat_smp_ops.init_irq_cpu(smp_processor_id());
+	if (plat_smp_ops.init_per_cpu)
+		plat_smp_ops.init_per_cpu(smp_processor_id());
 
-	if (machine_desc->init_cpu_smp)
-		machine_desc->init_cpu_smp(smp_processor_id());
+	if (machine_desc->init_per_cpu)
+		machine_desc->init_per_cpu(smp_processor_id());
 #endif
 }
 
@@ -51,6 +51,18 @@ void arch_do_IRQ(unsigned int irq, struct pt_regs *regs)
 	set_irq_regs(old_regs);
 }
 
+/*
+ * API called for requesting percpu interrupts - called by each CPU
+ *  - For boot CPU, actually request the IRQ with genirq core + enables
+ *  - For subsequent callers only enable called locally
+ *
+ * Relies on being called by boot cpu first (i.e. request called ahead) of
+ * any enable as expected by genirq. Hence Suitable only for TIMER, IPI
+ * which are guaranteed to be setup on boot core first.
+ * Late probed peripherals such as perf can't use this as there no guarantee
+ * of being called on boot CPU first.
+ */
+
 void arc_request_percpu_irq(int irq, int cpu,
                             irqreturn_t (*isr)(int irq, void *dev),
                             const char *irq_nm,
@@ -60,14 +72,17 @@ void arc_request_percpu_irq(int irq, int cpu,
 	if (!cpu) {
 		int rc;
 
+#ifdef CONFIG_ISA_ARCOMPACT
 		/*
-		 * These 2 calls are essential to making percpu IRQ APIs work
-		 * Ideally these details could be hidden in irq chip map function
-		 * but the issue is IPIs IRQs being static (non-DT) and platform
-		 * specific, so we can't identify them there.
+		 * A subsequent request_percpu_irq() fails if percpu_devid is
+		 * not set. That in turns sets NOAUTOEN, meaning each core needs
+		 * to call enable_percpu_irq()
+		 *
+		 * For ARCv2, this is done in irq map function since we know
+		 * which irqs are strictly per cpu
 		 */
 		irq_set_percpu_devid(irq);
-		irq_modify_status(irq, IRQ_NOAUTOEN, 0);  /* @irq, @clr, @set */
+#endif
 
 		rc = request_percpu_irq(irq, isr, irq_nm, percpu_dev);
 		if (rc)

arch/arc/kernel/mcip.c

@@ -132,7 +132,7 @@ static void mcip_probe_n_setup(void)
 struct plat_smp_ops plat_smp_ops = {
 	.info		= smp_cpuinfo_buf,
 	.init_early_smp	= mcip_probe_n_setup,
-	.init_irq_cpu	= mcip_setup_per_cpu,
+	.init_per_cpu	= mcip_setup_per_cpu,
 	.ipi_send	= mcip_ipi_send,
 	.ipi_clear	= mcip_ipi_clear,
 };

arch/arc/kernel/perf_event.c

@@ -428,12 +428,11 @@ static irqreturn_t arc_pmu_intr(int irq, void *dev)
 
 #endif /* CONFIG_ISA_ARCV2 */
 
-void arc_cpu_pmu_irq_init(void)
+static void arc_cpu_pmu_irq_init(void *data)
 {
-	struct arc_pmu_cpu *pmu_cpu = this_cpu_ptr(&arc_pmu_cpu);
+	int irq = *(int *)data;
 
-	arc_request_percpu_irq(arc_pmu->irq, smp_processor_id(), arc_pmu_intr,
-			       "ARC perf counters", pmu_cpu);
+	enable_percpu_irq(irq, IRQ_TYPE_NONE);
 
 	/* Clear all pending interrupt flags */
 	write_aux_reg(ARC_REG_PCT_INT_ACT, 0xffffffff);
@@ -515,7 +514,6 @@ static int arc_pmu_device_probe(struct platform_device *pdev)
 
 	if (has_interrupts) {
 		int irq = platform_get_irq(pdev, 0);
-		unsigned long flags;
 
 		if (irq < 0) {
 			pr_err("Cannot get IRQ number for the platform\n");
@@ -524,24 +522,12 @@ static int arc_pmu_device_probe(struct platform_device *pdev)
 
 		arc_pmu->irq = irq;
 
-		/*
-		 * arc_cpu_pmu_irq_init() needs to be called on all cores for
-		 * their respective local PMU.
-		 * However we use opencoded on_each_cpu() to ensure it is called
-		 * on core0 first, so that arc_request_percpu_irq() sets up
-		 * AUTOEN etc. Otherwise enable_percpu_irq() fails to enable
-		 * perf IRQ on non master cores.
-		 * see arc_request_percpu_irq()
-		 */
-		preempt_disable();
-		local_irq_save(flags);
-		arc_cpu_pmu_irq_init();
-		local_irq_restore(flags);
-		smp_call_function((smp_call_func_t)arc_cpu_pmu_irq_init, 0, 1);
-		preempt_enable();
-
-		/* Clean all pending interrupt flags */
-		write_aux_reg(ARC_REG_PCT_INT_ACT, 0xffffffff);
+		/* intc map function ensures irq_set_percpu_devid() called */
+		request_percpu_irq(irq, arc_pmu_intr, "ARC perf counters",
+				   this_cpu_ptr(&arc_pmu_cpu));
+
+		on_each_cpu(arc_cpu_pmu_irq_init, &irq, 1);
+
 	} else
 		arc_pmu->pmu.capabilities |= PERF_PMU_CAP_NO_INTERRUPT;
 

arch/arc/kernel/process.c

@@ -44,11 +44,10 @@ SYSCALL_DEFINE0(arc_gettls)
 void arch_cpu_idle(void)
 {
 	/* sleep, but enable all interrupts before committing */
-	if (is_isa_arcompact()) {
-		__asm__("sleep 0x3");
-	} else {
-		__asm__("sleep 0x10");
-	}
+	__asm__ __volatile__(
+		"sleep %0	\n"
+		:
+		:"I"(ISA_SLEEP_ARG)); /* can't be "r" has to be embedded const */
 }
 
 asmlinkage void ret_from_fork(void);

arch/arc/kernel/setup.c

@@ -429,7 +429,6 @@ void __init setup_arch(char **cmdline_p)
 #endif
 
 	arc_unwind_init();
-	arc_unwind_setup();
 }
 
 static int __init customize_machine(void)

arch/arc/kernel/smp.c

@@ -132,11 +132,11 @@ void start_kernel_secondary(void)
 	pr_info("## CPU%u LIVE ##: Executing Code...\n", cpu);
 
 	/* Some SMP H/w setup - for each cpu */
-	if (plat_smp_ops.init_irq_cpu)
-		plat_smp_ops.init_irq_cpu(cpu);
+	if (plat_smp_ops.init_per_cpu)
+		plat_smp_ops.init_per_cpu(cpu);
 
-	if (machine_desc->init_cpu_smp)
-		machine_desc->init_cpu_smp(cpu);
+	if (machine_desc->init_per_cpu)
+		machine_desc->init_per_cpu(cpu);
 
 	arc_local_timer_setup();
 

arch/arc/kernel/unwind.c

@@ -170,6 +170,23 @@ static struct unwind_table *find_table(unsigned long pc)
 
 static unsigned long read_pointer(const u8 **pLoc,
 				  const void *end, signed ptrType);
+static void init_unwind_hdr(struct unwind_table *table,
+			    void *(*alloc) (unsigned long));
+
+/*
+ * wrappers for header alloc (vs. calling one vs. other at call site)
+ * to elide section mismatches warnings
+ */
+static void *__init unw_hdr_alloc_early(unsigned long sz)
+{
+	return __alloc_bootmem_nopanic(sz, sizeof(unsigned int),
+				       MAX_DMA_ADDRESS);
+}
+
+static void *unw_hdr_alloc(unsigned long sz)
+{
+	return kmalloc(sz, GFP_KERNEL);
+}
 
 static void init_unwind_table(struct unwind_table *table, const char *name,
 			      const void *core_start, unsigned long core_size,
@@ -209,6 +226,8 @@ void __init arc_unwind_init(void)
 			  __start_unwind, __end_unwind - __start_unwind,
 			  NULL, 0);
 	  /*__start_unwind_hdr, __end_unwind_hdr - __start_unwind_hdr);*/
+
+	init_unwind_hdr(&root_table, unw_hdr_alloc_early);
 }
 
 static const u32 bad_cie, not_fde;
@@ -241,8 +260,8 @@ static void swap_eh_frame_hdr_table_entries(void *p1, void *p2, int size)
 	e2->fde = v;
 }
 
-static void __init setup_unwind_table(struct unwind_table *table,
-				      void *(*alloc) (unsigned long))
+static void init_unwind_hdr(struct unwind_table *table,
+			    void *(*alloc) (unsigned long))
 {
 	const u8 *ptr;
 	unsigned long tableSize = table->size, hdrSize;
@@ -277,10 +296,10 @@ static void __init setup_unwind_table(struct unwind_table *table,
 		if (cie == &not_fde)
 			continue;
 		if (cie == NULL || cie == &bad_cie)
-			return;
+			goto ret_err;
 		ptrType = fde_pointer_type(cie);
 		if (ptrType < 0)
-			return;
+			goto ret_err;
 
 		ptr = (const u8 *)(fde + 2);
 		if (!read_pointer(&ptr, (const u8 *)(fde + 1) + *fde,
@@ -296,13 +315,15 @@ static void __init setup_unwind_table(struct unwind_table *table,
 	}
 
 	if (tableSize || !n)
-		return;
+		goto ret_err;
 
 	hdrSize = 4 + sizeof(unsigned long) + sizeof(unsigned int)
 	    + 2 * n * sizeof(unsigned long);
+
 	header = alloc(hdrSize);
 	if (!header)
-		return;
+		goto ret_err;
+
 	header->version = 1;
 	header->eh_frame_ptr_enc = DW_EH_PE_abs | DW_EH_PE_native;
 	header->fde_count_enc = DW_EH_PE_abs | DW_EH_PE_data4;
@@ -340,18 +361,10 @@ static void __init setup_unwind_table(struct unwind_table *table,
 	table->hdrsz = hdrSize;
 	smp_wmb();
 	table->header = (const void *)header;
-}
-
-static void *__init balloc(unsigned long sz)
-{
-	return __alloc_bootmem_nopanic(sz,
-				       sizeof(unsigned int),
-				       __pa(MAX_DMA_ADDRESS));
-}
+	return;
 
-void __init arc_unwind_setup(void)
-{
-	setup_unwind_table(&root_table, balloc);
+ret_err:
+	panic("Attention !!! Dwarf FDE parsing errors\n");;
 }
 
 #ifdef CONFIG_MODULES
@@ -377,6 +390,8 @@ void *unwind_add_table(struct module *module, const void *table_start,
 			  table_start, table_size,
 			  NULL, 0);
 
+	init_unwind_hdr(table, unw_hdr_alloc);
+
 #ifdef UNWIND_DEBUG
 	unw_debug("Table added for [%s] %lx %lx\n",
 		module->name, table->core.pc, table->core.range);
@@ -439,6 +454,7 @@ void unwind_remove_table(void *handle, int init_only)
 	info.init_only = init_only;
 
 	unlink_table(&info); /* XXX: SMP */
+	kfree(table->header);
 	kfree(table);
 }
 
@@ -588,9 +604,6 @@ static signed fde_pointer_type(const u32 *cie)
 	const u8 *ptr = (const u8 *)(cie + 2);
 	unsigned version = *ptr;
 
-	if (version != 1)
-		return -1;	/* unsupported */
-
 	if (*++ptr) {
 		const char *aug;
 		const u8 *end = (const u8 *)(cie + 1) + *cie;
@@ -986,42 +999,13 @@ int arc_unwind(struct unwind_frame_info *frame)
 							    (const u8 *)(fde +
 									 1) +
 							    *fde, ptrType);
-				if (pc >= endLoc)
+				if (pc >= endLoc) {
 					fde = NULL;
-			} else
-				fde = NULL;
-		}
-		if (fde == NULL) {
-			for (fde = table->address, tableSize = table->size;
-			     cie = NULL, tableSize > sizeof(*fde)
-			     && tableSize - sizeof(*fde) >= *fde;
-			     tableSize -= sizeof(*fde) + *fde,
-			     fde += 1 + *fde / sizeof(*fde)) {
-				cie = cie_for_fde(fde, table);
-				if (cie == &bad_cie) {
 					cie = NULL;
-					break;
 				}
-				if (cie == NULL
-				    || cie == &not_fde
-				    || (ptrType = fde_pointer_type(cie)) < 0)
-					continue;
-				ptr = (const u8 *)(fde + 2);
-				startLoc = read_pointer(&ptr,
-							(const u8 *)(fde + 1) +
-							*fde, ptrType);
-				if (!startLoc)
-					continue;
-				if (!(ptrType & DW_EH_PE_indirect))
-					ptrType &=
-					    DW_EH_PE_FORM | DW_EH_PE_signed;
-				endLoc =
-				    startLoc + read_pointer(&ptr,
-							    (const u8 *)(fde +
-									 1) +
-							    *fde, ptrType);
-				if (pc >= startLoc && pc < endLoc)
-					break;
+			} else {
+				fde = NULL;
+				cie = NULL;
 			}
 		}
 	}
@@ -1031,9 +1015,7 @@ int arc_unwind(struct unwind_frame_info *frame)
 		ptr = (const u8 *)(cie + 2);
 		end = (const u8 *)(cie + 1) + *cie;
 		frame->call_frame = 1;
-		if ((state.version = *ptr) != 1)
-			cie = NULL;	/* unsupported version */
-		else if (*++ptr) {
+		if (*++ptr) {
 			/* check if augmentation size is first (thus present) */
 			if (*ptr == 'z') {
 				while (++ptr < end && *ptr) {

arch/arc/mm/highmem.c

@@ -111,7 +111,7 @@ void __kunmap_atomic(void *kv)
 }
 EXPORT_SYMBOL(__kunmap_atomic);
 
-noinline pte_t *alloc_kmap_pgtable(unsigned long kvaddr)
+static noinline pte_t * __init alloc_kmap_pgtable(unsigned long kvaddr)
 {
 	pgd_t *pgd_k;
 	pud_t *pud_k;
@@ -127,7 +127,7 @@ noinline pte_t *alloc_kmap_pgtable(unsigned long kvaddr)
 	return pte_k;
 }
 
-void kmap_init(void)
+void __init kmap_init(void)
 {
 	/* Due to recursive include hell, we can't do this in processor.h */
 	BUILD_BUG_ON(PAGE_OFFSET < (VMALLOC_END + FIXMAP_SIZE + PKMAP_SIZE));

arch/arc/mm/init.c

@@ -51,7 +51,9 @@ void __init early_init_dt_add_memory_arch(u64 base, u64 size)
 	int in_use = 0;
 
 	if (!low_mem_sz) {
-		BUG_ON(base != low_mem_start);
+		if (base != low_mem_start)
+			panic("CONFIG_LINUX_LINK_BASE != DT memory { }");
+
 		low_mem_sz = size;
 		in_use = 1;
 	} else {

arch/arc/mm/tlb.c

@@ -619,10 +619,10 @@ void update_mmu_cache(struct vm_area_struct *vma, unsigned long vaddr_unaligned,
 
 		int dirty = !test_and_set_bit(PG_dc_clean, &page->flags);
 		if (dirty) {
-			/* wback + inv dcache lines */
+			/* wback + inv dcache lines (K-mapping) */
 			__flush_dcache_page(paddr, paddr);
 
-			/* invalidate any existing icache lines */
+			/* invalidate any existing icache lines (U-mapping) */
 			if (vma->vm_flags & VM_EXEC)
 				__inv_icache_page(paddr, vaddr);
 		}

arch/arm/Kconfig

@@ -76,6 +76,8 @@ config ARM
 	select IRQ_FORCED_THREADING
 	select MODULES_USE_ELF_REL
 	select NO_BOOTMEM
+	select OF_EARLY_FLATTREE if OF
+	select OF_RESERVED_MEM if OF
 	select OLD_SIGACTION
 	select OLD_SIGSUSPEND3
 	select PERF_USE_VMALLOC
@@ -1825,8 +1827,6 @@ config USE_OF
 	bool "Flattened Device Tree support"
 	select IRQ_DOMAIN
 	select OF
-	select OF_EARLY_FLATTREE
-	select OF_RESERVED_MEM
 	help
 	  Include support for flattened device tree machine descriptions.
 

arch/arm/boot/dts/am4372.dtsi

@@ -74,7 +74,7 @@
 		reg = <0x48240200 0x100>;
 		interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-parent = <&gic>;
-		clocks = <&dpll_mpu_m2_ck>;
+		clocks = <&mpu_periphclk>;
 	};
 
 	local_timer: timer@48240600 {
@@ -82,7 +82,7 @@
 		reg = <0x48240600 0x100>;
 		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-parent = <&gic>;
-		clocks = <&dpll_mpu_m2_ck>;
+		clocks = <&mpu_periphclk>;
 	};
 
 	l2-cache-controller@48242000 {

arch/arm/boot/dts/am43xx-clocks.dtsi

@@ -259,6 +259,14 @@
 		ti,invert-autoidle-bit;
 	};
 
+	mpu_periphclk: mpu_periphclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_mpu_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
 	dpll_ddr_ck: dpll_ddr_ck {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -604,6 +604,7 @@
 		reg = <0x6f>;
 		interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>,
 				      <&dra7_pmx_core 0x424>;
+		interrupt-names = "irq", "wakeup";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcp79410_pins_default>;

arch/arm/boot/dts/animeo_ip.dts

@@ -155,21 +155,21 @@
 			label = "keyswitch_in";
 			gpios = <&pioB 1 GPIO_ACTIVE_HIGH>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		error_in {
 			label = "error_in";
 			gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
 			linux,code = <29>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		btn {
 			label = "btn";
 			gpios = <&pioC 23 GPIO_ACTIVE_HIGH>;
 			linux,code = <31>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 };

arch/arm/boot/dts/armada-38x.dtsi

@@ -498,6 +498,7 @@
 				reg = <0x70000 0x4000>;
 				interrupts-extended = <&mpic 8>;
 				clocks = <&gateclk 4>;
+				tx-csum-limit = <9800>;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91-foxg20.dts

@@ -159,7 +159,7 @@
 			label = "Button";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 };

arch/arm/boot/dts/at91-kizbox.dts

@@ -24,15 +24,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <18432000>;
-		};
-
 		main_xtal {
 			clock-frequency = <18432000>;
 		};
@@ -94,14 +85,14 @@
 			label = "PB_RST";
 			gpios = <&pioB 30 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		user {
 			label = "PB_USER";
 			gpios = <&pioB 31 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x101>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-kizbox2.dts

@@ -171,21 +171,21 @@
 			label = "PB_PROG";
 			gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		reset {
 			label = "PB_RST";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		user {
 			label = "PB_USER";
 			gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x101>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-kizboxmini.dts

@@ -98,14 +98,14 @@
 			label = "PB_PROG";
 			gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		reset {
 			label = "PB_RST";
 			gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-qil_a9260.dts

@@ -183,7 +183,7 @@
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-sama5d2_xplained.dts

@@ -45,6 +45,7 @@
 /dts-v1/;
 #include "sama5d2.dtsi"
 #include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
 
 / {
 	model = "Atmel SAMA5D2 Xplained";
@@ -59,15 +60,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -91,6 +83,22 @@
 			status = "okay";
 		};
 
+		sdmmc0: sdio-host@a0000000 {
+			bus-width = <8>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc0_default>;
+			non-removable;
+			mmc-ddr-1_8v;
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
 		apb {
 			spi0: spi@f8000000 {
 				pinctrl-names = "default";
@@ -176,17 +184,55 @@
 							regulator-name = "VDD_SDHC_1V8";
 							regulator-min-microvolt = <1800000>;
 							regulator-max-microvolt = <1800000>;
+							regulator-always-on;
 						};
 					};
 				};
 			};
 
+			flx0: flexcom@f8034000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+				status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
+
+				uart5: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx0_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx0_default>;
+					atmel,fifo-size = <32>;
+					status = "okay";
+				};
+			};
+
 			uart3: serial@fc008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart3_default>;
 				status = "okay";
 			};
 
+			flx4: flexcom@fc018000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+				status = "okay";
+
+				i2c2: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <0>, <0>;
+					dma-names = "tx", "rx";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&flx4_clk>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx4_default>;
+					atmel,fifo-size = <16>;
+					status = "okay";
+				};
+			};
+
 			i2c1: i2c@fc028000 {
 				dmas = <0>, <0>;
 				pinctrl-names = "default";
@@ -201,6 +247,18 @@
 			};
 
 			pinctrl@fc038000 {
+				pinctrl_flx0_default: flx0_default {
+					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+						 <PIN_PB29__FLEXCOM0_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx4_default: flx4_default {
+					pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+						 <PIN_PD13__FLEXCOM4_IO1>;
+					bias-disable;
+				};
+
 				pinctrl_i2c0_default: i2c0_default {
 					pinmux = <PIN_PD21__TWD0>,
 						 <PIN_PD22__TWCK0>;
@@ -227,6 +285,46 @@
 					bias-disable;
 				};
 
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>,
+							 <PIN_PA6__SDMMC0_DAT4>,
+							 <PIN_PA7__SDMMC0_DAT5>,
+							 <PIN_PA8__SDMMC0_DAT6>,
+							 <PIN_PA9__SDMMC0_DAT7>;
+						bias-pull-up;
+					};
+
+					ck_cd_rstn_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA10__SDMMC0_RSTN>,
+							 <PIN_PA11__SDMMC0_VDDSEL>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>,
+							 <PIN_PA30__SDMMC1_CD>;
+						bias-disable;
+					};
+				};
+
 				pinctrl_spi0_default: spi0_default {
 					pinmux = <PIN_PA14__SPI0_SPCK>,
 						 <PIN_PA15__SPI0_MOSI>,

arch/arm/boot/dts/at91-sama5d3_xplained.dts

@@ -315,7 +315,7 @@
 			label = "PB_USER";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x104>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-sama5d4_xplained.dts

@@ -50,7 +50,6 @@
 	compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "ignore_loglevel earlyprintk";
 		stdout-path = "serial0:115200n8";
 	};
 
@@ -59,15 +58,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -235,7 +225,7 @@
 			label = "pb_user1";
 			gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-sama5d4ek.dts

@@ -50,7 +50,6 @@
 	compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "ignore_loglevel earlyprintk";
 		stdout-path = "serial0:115200n8";
 	};
 
@@ -59,15 +58,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -304,7 +294,7 @@
 			label = "pb_user1";
 			gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91rm9200ek.dts

@@ -21,15 +21,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <18432000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};

arch/arm/boot/dts/at91sam9261ek.dts

@@ -22,15 +22,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <18432000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -149,7 +140,7 @@
 					ti,debounce-tol = /bits/ 16 <65535>;
 					ti,debounce-max = /bits/ 16 <1>;
 
-					linux,wakeup;
+					wakeup-source;
 				};
 			};
 
@@ -193,28 +184,28 @@
 			label = "button_0";
 			gpios = <&pioA 27 GPIO_ACTIVE_LOW>;
 			linux,code = <256>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		button_1 {
 			label = "button_1";
 			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
 			linux,code = <257>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		button_2 {
 			label = "button_2";
 			gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
 			linux,code = <258>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		button_3 {
 			label = "button_3";
 			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
 			linux,code = <259>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 };

arch/arm/boot/dts/at91sam9263ek.dts

@@ -22,15 +22,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <16367660>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -213,14 +204,14 @@
 			label = "left_click";
 			gpios = <&pioC 5 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		right_click {
 			label = "right_click";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91sam9g20ek_common.dtsi

@@ -19,15 +19,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <18432000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -206,14 +197,14 @@
 			label = "Button 3";
 			gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		btn4 {
 			label = "Button 4";
 			gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
 			linux,code = <0x104>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91sam9m10g45ek.dts

@@ -24,15 +24,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 		      clock-frequency = <32768>;
 		};
@@ -323,14 +314,14 @@
 			label = "left_click";
 			gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		right_click {
 			label = "right_click";
 			gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		left {

arch/arm/boot/dts/at91sam9n12ek.dts

@@ -23,15 +23,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <16000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -219,7 +210,7 @@
 			label = "Enter";
 			gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91sam9rlek.dts

@@ -22,15 +22,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -225,14 +216,14 @@
 			label = "right_click";
 			gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		left_click {
 			label = "left_click";
 			gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91sam9x5cm.dtsi

@@ -12,17 +12,6 @@
 		reg = <0x20000000 0x8000000>;
 	};
 
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-	};
-
 	clocks {
 		slow_xtal {
 			clock-frequency = <32768>;

arch/arm/boot/dts/berlin2q.dtsi

@@ -118,7 +118,8 @@
 		sdhci0: sdhci@ab0000 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab0000 0x200>;
-			clocks = <&chip_clk CLKID_SDIO1XIN>;
+			clocks = <&chip_clk CLKID_SDIO1XIN>, <&chip_clk CLKID_SDIO>;
+			clock-names = "io", "core";
 			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
@@ -126,7 +127,8 @@
 		sdhci1: sdhci@ab0800 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab0800 0x200>;
-			clocks = <&chip_clk CLKID_SDIO1XIN>;
+			clocks = <&chip_clk CLKID_SDIO1XIN>, <&chip_clk CLKID_SDIO>;
+			clock-names = "io", "core";
 			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
@@ -135,7 +137,7 @@
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab1000 0x200>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&chip_clk CLKID_NFC_ECC>, <&chip_clk CLKID_NFC>;
+			clocks = <&chip_clk CLKID_NFC_ECC>, <&chip_clk CLKID_SDIO>;
 			clock-names = "io", "core";
 			status = "disabled";
 		};

arch/arm/boot/dts/dm816x.dtsi

@@ -218,6 +218,7 @@
 			reg = <0x480c8000 0x2000>;
 			interrupts = <77>;
 			ti,hwmods = "mailbox";
+			#mbox-cells = <1>;
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <12>;
 			mbox_dsp: mbox_dsp {
@@ -279,8 +280,11 @@
 			ti,spi-num-cs = <4>;
 			ti,hwmods = "mcspi1";
 			dmas = <&edma 16 &edma 17
-				&edma 18 &edma 19>;
-			dma-names = "tx0", "rx0", "tx1", "rx1";
+				&edma 18 &edma 19
+				&edma 20 &edma 21
+				&edma 22 &edma 23>;
+			dma-names = "tx0", "rx0", "tx1", "rx1",
+				    "tx2", "rx2", "tx3", "rx3";
 		};
 
 		mmc1: mmc@48060000 {

arch/arm/boot/dts/dra7.dtsi

@@ -1459,8 +1459,8 @@
 			interrupt-names = "tx", "rx";
 			dmas = <&sdma_xbar 133>, <&sdma_xbar 132>;
 			dma-names = "tx", "rx";
-			clocks = <&mcasp3_ahclkx_mux>;
-			clock-names = "fck";
+			clocks = <&mcasp3_aux_gfclk_mux>, <&mcasp3_ahclkx_mux>;
+			clock-names = "fck", "ahclkx";
 			status = "disabled";
 		};
 

arch/arm/boot/dts/imx6q-gw5400-a.dts

@@ -154,7 +154,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-gw51xx.dtsi

@@ -94,7 +94,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-gw52xx.dtsi

@@ -154,7 +154,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-gw53xx.dtsi

@@ -155,7 +155,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-gw54xx.dtsi

@@ -145,7 +145,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-sabreauto.dtsi

@@ -113,14 +113,14 @@
 &clks {
 	assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 			  <&clks IMX6QDL_PLL4_BYPASS>,
-			  <&clks IMX6QDL_CLK_PLL4_POST_DIV>,
 			  <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+			  <&clks IMX6QDL_CLK_PLL4_POST_DIV>;
 	assigned-clock-parents = <&clks IMX6QDL_CLK_LVDS2_IN>,
 				 <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
 				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-	assigned-clock-rates = <0>, <0>, <24576000>;
+	assigned-clock-rates = <0>, <0>, <0>, <0>, <24576000>;
 };
 
 &ecspi1 {

arch/arm/boot/dts/k2l-netcp.dtsi

@@ -137,7 +137,7 @@ netcp: netcp@26000000 {
 	/* NetCP address range */
 	ranges = <0 0x26000000 0x1000000>;
 
-	clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>;
+	clocks = <&clkosr>, <&papllclk>, <&clkcpgmac>, <&chipclk12>;
 	dma-coherent;
 
 	ti,navigator-dmas = <&dma_gbe 0>,

arch/arm/boot/dts/kirkwood-ts219.dtsi

@@ -40,7 +40,7 @@
 		};
 		poweroff@12100 {
 			compatible = "qnap,power-off";
-			reg = <0x12000 0x100>;
+			reg = <0x12100 0x100>;
 			clocks = <&gate_clk 7>;
 		};
 		spi@10600 {

arch/arm/boot/dts/omap4-duovero-parlor.dts

@@ -189,3 +189,7 @@
 	};
 };
 
+&uart3 {
+	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
+			       &omap4_pmx_core OMAP4_UART3_RX>;
+};

arch/arm/boot/dts/rk3288-veyron-minnie.dts

@@ -86,6 +86,10 @@
 	};
 };
 
+&emmc {
+	/delete-property/mmc-hs200-1_8v;
+};
+
 &gpio_keys {
 	pinctrl-0 = <&pwr_key_l &ap_lid_int_l &volum_down_l &volum_up_l>;
 

arch/arm/boot/dts/rk3288.dtsi

@@ -452,8 +452,10 @@
 		clock-names = "tsadc", "apb_pclk";
 		resets = <&cru SRST_TSADC>;
 		reset-names = "tsadc-apb";
-		pinctrl-names = "default";
-		pinctrl-0 = <&otp_out>;
+		pinctrl-names = "init", "default", "sleep";
+		pinctrl-0 = <&otp_gpio>;
+		pinctrl-1 = <&otp_out>;
+		pinctrl-2 = <&otp_gpio>;
 		#thermal-sensor-cells = <1>;
 		rockchip,hw-tshut-temp = <95000>;
 		status = "disabled";
@@ -1395,6 +1397,10 @@
 		};
 
 		tsadc {
+			otp_gpio: otp-gpio {
+				rockchip,pins = <0 10 RK_FUNC_GPIO &pcfg_pull_none>;
+			};
+
 			otp_out: otp-out {
 				rockchip,pins = <0 10 RK_FUNC_1 &pcfg_pull_none>;
 			};

arch/arm/boot/dts/sama5d35ek.dts

@@ -49,7 +49,7 @@
 			label = "pb_user1";
 			gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 };

arch/arm/boot/dts/sama5d4.dtsi

@@ -1300,7 +1300,7 @@
 			};
 
 			watchdog@fc068640 {
-				compatible = "atmel,at91sam9260-wdt";
+				compatible = "atmel,sama5d4-wdt";
 				reg = <0xfc068640 0x10>;
 				clocks = <&clk32k>;
 				status = "disabled";

arch/arm/boot/dts/sun6i-a31s-primo81.dts

@@ -83,6 +83,7 @@
 		reg = <0x5d>;
 		interrupt-parent = <&pio>;
 		interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>; /* PA3 */
+		touchscreen-swapped-x-y;
 	};
 };
 

arch/arm/boot/dts/tegra124-nyan.dtsi

@@ -399,7 +399,7 @@
 
 	/* CPU DFLL clock */
 	clock@0,70110000 {
-		status = "okay";
+		status = "disabled";
 		vdd-cpu-supply = <&vdd_cpu>;
 		nvidia,i2c-fs-rate = <400000>;
 	};

arch/arm/boot/dts/usb_a9260_common.dtsi

@@ -115,7 +115,7 @@
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/usb_a9263.dts

@@ -143,7 +143,7 @@
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/vf610-colibri.dtsi

@@ -18,8 +18,3 @@
 		reg = <0x80000000 0x10000000>;
 	};
 };
-
-&L2 {
-	arm,data-latency = <2 1 2>;
-	arm,tag-latency = <3 2 3>;
-};

arch/arm/boot/dts/vf610.dtsi

@@ -19,7 +19,7 @@
 		reg = <0x40006000 0x1000>;
 		cache-unified;
 		cache-level = <2>;
-		arm,data-latency = <1 1 1>;
+		arm,data-latency = <3 3 3>;
 		arm,tag-latency = <2 2 2>;
 	};
 };

arch/arm/boot/dts/vfxxx.dtsi

@@ -158,7 +158,7 @@
 				interrupts = <67 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_DSPI0>;
 				clock-names = "dspi";
-				spi-num-chipselects = <5>;
+				spi-num-chipselects = <6>;
 				status = "disabled";
 			};
 
@@ -170,7 +170,7 @@
 				interrupts = <68 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_DSPI1>;
 				clock-names = "dspi";
-				spi-num-chipselects = <5>;
+				spi-num-chipselects = <4>;
 				status = "disabled";
 			};
 
@@ -178,8 +178,10 @@
 				compatible = "fsl,vf610-sai";
 				reg = <0x40031000 0x1000>;
 				interrupts = <86 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clks VF610_CLK_SAI2>;
-				clock-names = "sai";
+				clocks = <&clks VF610_CLK_SAI2>,
+					<&clks VF610_CLK_SAI2_DIV>,
+					<&clks 0>, <&clks 0>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
 				dma-names = "tx", "rx";
 				dmas = <&edma0 0 21>,
 					<&edma0 0 20>;
@@ -461,6 +463,8 @@
 				clock-names = "adc";
 				#io-channel-cells = <1>;
 				status = "disabled";
+				fsl,adck-max-frequency = <30000000>, <40000000>,
+							<20000000>;
 			};
 
 			esdhc0: esdhc@400b1000 {
@@ -472,8 +476,6 @@
 					<&clks VF610_CLK_ESDHC0>;
 				clock-names = "ipg", "ahb", "per";
 				status = "disabled";
-				fsl,adck-max-frequency = <30000000>, <40000000>,
-							<20000000>;
 			};
 
 			esdhc1: esdhc@400b2000 {

arch/arm/configs/at91_dt_defconfig

@@ -125,7 +125,6 @@ CONFIG_POWER_RESET=y
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
 CONFIG_AT91SAM9X_WATCHDOG=y
-CONFIG_SSB=m
 CONFIG_MFD_ATMEL_HLCDC=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y

arch/arm/configs/sama5_defconfig

@@ -129,7 +129,6 @@ CONFIG_GPIO_SYSFS=y
 CONFIG_POWER_SUPPLY=y
 CONFIG_POWER_RESET=y
 # CONFIG_HWMON is not set
-CONFIG_SSB=m
 CONFIG_MFD_ATMEL_FLEXCOM=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y

arch/arm/include/asm/arch_gicv3.h

@@ -21,6 +21,7 @@
 #ifndef __ASSEMBLY__
 
 #include <linux/io.h>
+#include <asm/barrier.h>
 
 #define __ACCESS_CP15(CRn, Op1, CRm, Op2)	p15, Op1, %0, CRn, CRm, Op2
 #define __ACCESS_CP15_64(Op1, CRm)		p15, Op1, %Q0, %R0, CRm

arch/arm/include/asm/irq.h

@@ -40,6 +40,11 @@ extern void arch_trigger_all_cpu_backtrace(bool);
 #define arch_trigger_all_cpu_backtrace(x) arch_trigger_all_cpu_backtrace(x)
 #endif
 
+static inline int nr_legacy_irqs(void)
+{
+	return NR_IRQS_LEGACY;
+}
+
 #endif
 
 #endif

arch/arm/include/asm/kvm_emulate.h

@@ -28,6 +28,18 @@
 unsigned long *vcpu_reg(struct kvm_vcpu *vcpu, u8 reg_num);
 unsigned long *vcpu_spsr(struct kvm_vcpu *vcpu);
 
+static inline unsigned long vcpu_get_reg(struct kvm_vcpu *vcpu,
+					 u8 reg_num)
+{
+	return *vcpu_reg(vcpu, reg_num);
+}
+
+static inline void vcpu_set_reg(struct kvm_vcpu *vcpu, u8 reg_num,
+				unsigned long val)
+{
+	*vcpu_reg(vcpu, reg_num) = val;
+}
+
 bool kvm_condition_valid(struct kvm_vcpu *vcpu);
 void kvm_skip_instr(struct kvm_vcpu *vcpu, bool is_wide_instr);
 void kvm_inject_undefined(struct kvm_vcpu *vcpu);

arch/arm/include/asm/uaccess.h

@@ -510,10 +510,14 @@ __copy_to_user_std(void __user *to, const void *from, unsigned long n);
 static inline unsigned long __must_check
 __copy_to_user(void __user *to, const void *from, unsigned long n)
 {
+#ifndef CONFIG_UACCESS_WITH_MEMCPY
 	unsigned int __ua_flags = uaccess_save_and_enable();
 	n = arm_copy_to_user(to, from, n);
 	uaccess_restore(__ua_flags);
 	return n;
+#else
+	return arm_copy_to_user(to, from, n);
+#endif
 }
 
 extern unsigned long __must_check

arch/arm/include/uapi/asm/unistd.h

@@ -416,6 +416,7 @@
 #define __NR_execveat			(__NR_SYSCALL_BASE+387)
 #define __NR_userfaultfd		(__NR_SYSCALL_BASE+388)
 #define __NR_membarrier			(__NR_SYSCALL_BASE+389)
+#define __NR_mlock2			(__NR_SYSCALL_BASE+390)
 
 /*
  * The following SWIs are ARM private.

arch/arm/kernel/bios32.c

@@ -17,11 +17,6 @@
 #include <asm/mach/pci.h>
 
 static int debug_pci;
-static resource_size_t (*align_resource)(struct pci_dev *dev,
-		  const struct resource *res,
-		  resource_size_t start,
-		  resource_size_t size,
-		  resource_size_t align) = NULL;
 
 /*
  * We can't use pci_get_device() here since we are
@@ -461,7 +456,6 @@ static void pcibios_init_hw(struct device *parent, struct hw_pci *hw,
 		sys->busnr   = busnr;
 		sys->swizzle = hw->swizzle;
 		sys->map_irq = hw->map_irq;
-		align_resource = hw->align_resource;
 		INIT_LIST_HEAD(&sys->resources);
 
 		if (hw->private_data)
@@ -470,6 +464,8 @@ static void pcibios_init_hw(struct device *parent, struct hw_pci *hw,
 		ret = hw->setup(nr, sys);
 
 		if (ret > 0) {
+			struct pci_host_bridge *host_bridge;
+
 			ret = pcibios_init_resources(nr, sys);
 			if (ret)  {
 				kfree(sys);
@@ -491,6 +487,9 @@ static void pcibios_init_hw(struct device *parent, struct hw_pci *hw,
 			busnr = sys->bus->busn_res.end + 1;
 
 			list_add(&sys->node, head);
+
+			host_bridge = pci_find_host_bridge(sys->bus);
+			host_bridge->align_resource = hw->align_resource;
 		} else {
 			kfree(sys);
 			if (ret < 0)
@@ -578,14 +577,18 @@ resource_size_t pcibios_align_resource(void *data, const struct resource *res,
 {
 	struct pci_dev *dev = data;
 	resource_size_t start = res->start;
+	struct pci_host_bridge *host_bridge;
 
 	if (res->flags & IORESOURCE_IO && start & 0x300)
 		start = (start + 0x3ff) & ~0x3ff;
 
 	start = (start + align - 1) & ~(align - 1);
 
-	if (align_resource)
-		return align_resource(dev, res, start, size, align);
+	host_bridge = pci_find_host_bridge(dev->bus);
+
+	if (host_bridge->align_resource)
+		return host_bridge->align_resource(dev, res,
+				start, size, align);
 
 	return start;
 }

arch/arm/kernel/calls.S

@@ -399,6 +399,7 @@
 		CALL(sys_execveat)
 		CALL(sys_userfaultfd)
 		CALL(sys_membarrier)
+		CALL(sys_mlock2)
 #ifndef syscalls_counted
 .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
 #define syscalls_counted

arch/arm/kernel/process.c

@@ -95,6 +95,22 @@ void __show_regs(struct pt_regs *regs)
 {
 	unsigned long flags;
 	char buf[64];
+#ifndef CONFIG_CPU_V7M
+	unsigned int domain;
+#ifdef CONFIG_CPU_SW_DOMAIN_PAN
+	/*
+	 * Get the domain register for the parent context. In user
+	 * mode, we don't save the DACR, so lets use what it should
+	 * be. For other modes, we place it after the pt_regs struct.
+	 */
+	if (user_mode(regs))
+		domain = DACR_UACCESS_ENABLE;
+	else
+		domain = *(unsigned int *)(regs + 1);
+#else
+	domain = get_domain();
+#endif
+#endif
 
 	show_regs_print_info(KERN_DEFAULT);
 
@@ -123,21 +139,8 @@ void __show_regs(struct pt_regs *regs)
 
 #ifndef CONFIG_CPU_V7M
 	{
-		unsigned int domain = get_domain();
 		const char *segment;
 
-#ifdef CONFIG_CPU_SW_DOMAIN_PAN
-		/*
-		 * Get the domain register for the parent context. In user
-		 * mode, we don't save the DACR, so lets use what it should
-		 * be. For other modes, we place it after the pt_regs struct.
-		 */
-		if (user_mode(regs))
-			domain = DACR_UACCESS_ENABLE;
-		else
-			domain = *(unsigned int *)(regs + 1);
-#endif
-
 		if ((domain & domain_mask(DOMAIN_USER)) ==
 		    domain_val(DOMAIN_USER, DOMAIN_NOACCESS))
 			segment = "none";
@@ -163,11 +166,11 @@ void __show_regs(struct pt_regs *regs)
 		buf[0] = '\0';
 #ifdef CONFIG_CPU_CP15_MMU
 		{
-			unsigned int transbase, dac = get_domain();
+			unsigned int transbase;
 			asm("mrc p15, 0, %0, c2, c0\n\t"
 			    : "=r" (transbase));
 			snprintf(buf, sizeof(buf), "  Table: %08x  DAC: %08x",
-			  	transbase, dac);
+				transbase, domain);
 		}
 #endif
 		asm("mrc p15, 0, %0, c1, c0\n" : "=r" (ctrl));

arch/arm/kernel/swp_emulate.c

@@ -36,10 +36,10 @@
  */
 #define __user_swpX_asm(data, addr, res, temp, B)		\
 	__asm__ __volatile__(					\
-	"	mov		%2, %1\n"			\
-	"0:	ldrex"B"	%1, [%3]\n"			\
-	"1:	strex"B"	%0, %2, [%3]\n"			\
+	"0:	ldrex"B"	%2, [%3]\n"			\
+	"1:	strex"B"	%0, %1, [%3]\n"			\
 	"	cmp		%0, #0\n"			\
+	"	moveq		%1, %2\n"			\
 	"	movne		%0, %4\n"			\
 	"2:\n"							\
 	"	.section	 .text.fixup,\"ax\"\n"		\