Merge branch 'gpio-key-wakeup-fix' into omap-for-v4.11/fixes

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -151,6 +151,9 @@ Boards:
 - AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4
   compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"
 
+- AM335X phyCORE-AM335x: Development kit
+  compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx"
+
 - OMAP5 EVM : Evaluation Module
   compatible = "ti,omap5-evm", "ti,omap5"
 

arch/arm/boot/dts/Makefile

@@ -564,7 +564,9 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-base0033.dtb \
 	am335x-bone.dtb \
 	am335x-boneblack.dtb \
+	am335x-boneblack-wireless.dtb \
 	am335x-bonegreen.dtb \
+	am335x-bonegreen-wireless.dtb \
 	am335x-chiliboard.dtb \
 	am335x-cm-t335.dtb \
 	am335x-evm.dtb \
@@ -573,6 +575,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-lxm.dtb \
 	am335x-nano.dtb \
 	am335x-pepper.dtb \
+	am335x-phycore-rdk.dtb \
 	am335x-shc.dtb \
 	am335x-sbc-t335.dtb \
 	am335x-sl50.dtb \

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -207,6 +207,8 @@
 &usb0 {
 	status = "okay";
 	dr_mode = "peripheral";
+	interrupts-extended = <&intc 18 &tps 0>;
+	interrupt-names = "mc", "vbus";
 };
 
 &usb1 {

arch/arm/boot/dts/am335x-boneblack-common.dtsi

@@ -0,0 +1,163 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/display/tda998x.h>
+
+&ldo3_reg {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins>;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&am33xx_pinmux {
+	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr0 */
+			AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data0.lcd_data0 */
+			AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data1.lcd_data1 */
+			AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data2.lcd_data2 */
+			AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0)		/* lcd_data3.lcd_data3 */
+			AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data4.lcd_data4 */
+			AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data5.lcd_data5 */
+			AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data6.lcd_data6 */
+			AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0)		/* lcd_data7.lcd_data7 */
+			AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data8.lcd_data8 */
+			AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data9.lcd_data9 */
+			AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data10.lcd_data10 */
+			AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0)		/* lcd_data11.lcd_data11 */
+			AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data12.lcd_data12 */
+			AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data13.lcd_data13 */
+			AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data14.lcd_data14 */
+			AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0)		/* lcd_data15.lcd_data15 */
+			AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_vsync.lcd_vsync */
+			AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_hsync.lcd_hsync */
+			AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_pclk.lcd_pclk */
+			AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_ac_bias_en.lcd_ac_bias_en */
+		>;
+	};
+
+	nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr0 */
+		>;
+	};
+
+	mcasp0_pins: mcasp0_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
+			AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
+			AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
+			AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
+			AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */
+		>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+
+	/* If you want to get 24 bit RGB and 16 BGR mode instead of
+	 * current 16 bit RGB and 24 BGR modes, set the propety
+	 * below to "crossed" and uncomment the video-ports -property
+	 * in tda19988 node.
+	 */
+	blue-and-red-wiring = "straight";
+
+	port {
+		lcdc_0: endpoint@0 {
+			remote-endpoint = <&hdmi_0>;
+		};
+	};
+};
+
+&i2c0 {
+	tda19988: tda19988 {
+		compatible = "nxp,tda998x";
+		reg = <0x70>;
+
+		pinctrl-names = "default", "off";
+		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+
+		/* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
+		/* video-ports = <0x234501>; */
+
+		#sound-dai-cells = <0>;
+		audio-ports = <	TDA998x_I2S	0x03>;
+
+		ports {
+			port@0 {
+				hdmi_0: endpoint@0 {
+					remote-endpoint = <&lcdc_0>;
+				};
+			};
+		};
+	};
+};
+
+&rtc {
+	system-power-controller;
+};
+
+&mcasp0	{
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp0_pins>;
+	status = "okay";
+	op-mode = <0>;	/* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 0
+		>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
+
+/ {
+	clk_mcasp0_fixed: clk_mcasp0_fixed {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24576000>;
+	};
+
+	clk_mcasp0: clk_mcasp0 {
+		#clock-cells = <0>;
+		compatible = "gpio-gate-clock";
+		clocks = <&clk_mcasp0_fixed>;
+		enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "TI BeagleBone Black";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink0_master>;
+		simple-audio-card,frame-master = <&dailink0_master>;
+
+		dailink0_master: simple-audio-card,cpu {
+			sound-dai = <&mcasp0>;
+			clocks = <&clk_mcasp0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&tda19988>;
+		};
+	};
+};

arch/arm/boot/dts/am335x-boneblack-wireless.dts

@@ -0,0 +1,109 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "TI AM335x BeagleBone Black Wireless";
+	compatible = "ti,am335x-bone-black-wireless", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+	wlan_en_reg: fixedregulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		startup-delay-us= <70000>;
+
+		/* WL_EN */
+		gpio = <&gpio3 9 0>;
+		enable-active-high;
+	};
+};
+
+&am33xx_pinmux {
+	bt_pins: pinmux_bt_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gmii1_txd0.gpio0_28 - BT_EN */
+		>;
+	};
+
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */
+			AM33XX_IOPAD(0x914, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */
+			AM33XX_IOPAD(0x91c, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */
+			AM33XX_IOPAD(0x920, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */
+			AM33XX_IOPAD(0x908, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1)	/* gmii1_rxd3.uart3_rxd */
+			AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* gmii1_rxd2.uart3_txd */
+			AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3)		/* mdio_data.uart3_ctsn */
+			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* mdio_clk.uart3_rtsn */
+		>;
+	};
+
+	wl18xx_pins: pinmux_wl18xx_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gmii1_txclk.gpio3_9 WL_EN */
+			AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_refclk.gpio0_29 WL_IRQ */
+			AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gmii1_rxclk.gpio3_10 LS_BUF_EN */
+		>;
+	};
+};
+
+&mac {
+	status = "disabled";
+};
+
+&mmc3 {
+	dmas = <&edma_xbar 12 0 1
+		&edma_xbar 13 0 2>;
+	dma-names = "tx", "rx";
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	ti,needs-special-hs-handling;
+	keep-power-in-suspend;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins &bt_pins>;
+	status = "okay";
+};
+
+&gpio3 {
+	ls_buf_en {
+		gpio-hog;
+		gpios = <10 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "LS_BUF_EN";
+	};
+};

arch/arm/boot/dts/am335x-boneblack.dts

@@ -9,162 +9,9 @@
 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
-#include <dt-bindings/display/tda998x.h>
+#include "am335x-boneblack-common.dtsi"
 
 / {
 	model = "TI AM335x BeagleBone Black";
 	compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
 };
-
-&ldo3_reg {
-	regulator-min-microvolt = <1800000>;
-	regulator-max-microvolt = <1800000>;
-	regulator-always-on;
-};
-
-&mmc1 {
-	vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
-	vmmc-supply = <&vmmcsd_fixed>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_pins>;
-	bus-width = <8>;
-	status = "okay";
-};
-
-&am33xx_pinmux {
-	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
-		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr0 */
-			AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data0.lcd_data0 */
-			AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data1.lcd_data1 */
-			AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data2.lcd_data2 */
-			AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0)		/* lcd_data3.lcd_data3 */
-			AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data4.lcd_data4 */
-			AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data5.lcd_data5 */
-			AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data6.lcd_data6 */
-			AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0)		/* lcd_data7.lcd_data7 */
-			AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data8.lcd_data8 */
-			AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data9.lcd_data9 */
-			AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data10.lcd_data10 */
-			AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0)		/* lcd_data11.lcd_data11 */
-			AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0)		/* lcd_data12.lcd_data12 */
-			AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0)		/* lcd_data13.lcd_data13 */
-			AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0)		/* lcd_data14.lcd_data14 */
-			AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0)		/* lcd_data15.lcd_data15 */
-			AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_vsync.lcd_vsync */
-			AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_hsync.lcd_hsync */
-			AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_pclk.lcd_pclk */
-			AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* lcd_ac_bias_en.lcd_ac_bias_en */
-		>;
-	};
-	nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
-		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr0 */
-		>;
-	};
-
-	mcasp0_pins: mcasp0_pins {
-		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
-			AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
-			AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
-			AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
-			AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */
-		>;
-	};
-};
-
-&lcdc {
-	status = "okay";
-
-	/* If you want to get 24 bit RGB and 16 BGR mode instead of
-	 * current 16 bit RGB and 24 BGR modes, set the propety
-	 * below to "crossed" and uncomment the video-ports -property
-	 * in tda19988 node.
-	 */
-	blue-and-red-wiring = "straight";
-
-	port {
-		lcdc_0: endpoint@0 {
-			remote-endpoint = <&hdmi_0>;
-		};
-	};
-};
-
-&i2c0 {
-	tda19988: tda19988 {
-		compatible = "nxp,tda998x";
-		reg = <0x70>;
-
-		pinctrl-names = "default", "off";
-		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
-		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
-
-		/* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
-		/* video-ports = <0x234501>; */
-
-		#sound-dai-cells = <0>;
-		audio-ports = <	TDA998x_I2S	0x03>;
-
-		ports {
-			port@0 {
-				hdmi_0: endpoint@0 {
-					remote-endpoint = <&lcdc_0>;
-				};
-			};
-		};
-	};
-};
-
-&rtc {
-	system-power-controller;
-};
-
-&mcasp0	{
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcasp0_pins>;
-	status = "okay";
-	op-mode = <0>;	/* MCASP_IIS_MODE */
-	tdm-slots = <2>;
-	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
-			0 0 1 0
-		>;
-	tx-num-evt = <32>;
-	rx-num-evt = <32>;
-};
-
-/ {
-	clk_mcasp0_fixed: clk_mcasp0_fixed {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <24576000>;
-	};
-
-	clk_mcasp0: clk_mcasp0 {
-		#clock-cells = <0>;
-		compatible = "gpio-gate-clock";
-		clocks = <&clk_mcasp0_fixed>;
-		enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
-	};
-
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "TI BeagleBone Black";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,bitclock-master = <&dailink0_master>;
-		simple-audio-card,frame-master = <&dailink0_master>;
-
-		dailink0_master: simple-audio-card,cpu {
-			sound-dai = <&mcasp0>;
-			clocks = <&clk_mcasp0>;
-		};
-
-		simple-audio-card,codec {
-			sound-dai = <&tda19988>;
-		};
-	};
-};

arch/arm/boot/dts/am335x-bonegreen-common.dtsi

@@ -0,0 +1,44 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&ldo3_reg {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins>;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&am33xx_pinmux {
+	uart2_pins: uart2_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1)	/* spi0_sclk.uart2_rxd */
+			AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1)	/* spi0_d0.uart2_txd */
+		>;
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&rtc {
+	system-power-controller;
+};

arch/arm/boot/dts/am335x-bonegreen-wireless.dts

@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "TI AM335x BeagleBone Green Wireless";
+	compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+	wlan_en_reg: fixedregulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		startup-delay-us= <70000>;
+
+		/* WL_EN */
+		gpio = <&gpio0 26 0>;
+		enable-active-high;
+	};
+};
+
+&am33xx_pinmux {
+	bt_pins: pinmux_bt_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x878, PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_ad12.gpio1_28 BT_EN */
+		>;
+	};
+
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_ad12.mmc2_dat0 */
+			AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_ad13.mmc2_dat1 */
+			AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_ad14.mmc2_dat2 */
+			AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_ad15.mmc2_dat3 */
+			AM33XX_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_csn3.mmc2_cmd */
+			AM33XX_IOPAD(0x88c, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_clk.mmc2_clk */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1)	/* gmii1_rxd3.uart3_rxd */
+			AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* gmii1_rxd2.uart3_txd */
+			AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3)		/* mdio_data.uart3_ctsn */
+			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* mdio_clk.uart3_rtsn */
+		>;
+	};
+
+	wl18xx_pins: pinmux_wl18xx_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x828, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_ad10.gpio0_26 WL_EN */
+			AM33XX_IOPAD(0x82C, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_ad11.gpio0_27 WL_IRQ */
+			AM33XX_IOPAD(0x87C, PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_csn0.gpio1_29 LS_BUF_EN */
+		>;
+	};
+};
+
+&mac {
+	status = "disabled";
+};
+
+&mmc3 {
+	dmas = <&edma_xbar 12 0 1
+		&edma_xbar 13 0 2>;
+	dma-names = "tx", "rx";
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	ti,needs-special-hs-handling;
+	keep-power-in-suspend;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins &bt_pins>;
+	status = "okay";
+};
+
+&gpio1 {
+	ls_buf_en {
+		gpio-hog;
+		gpios = <29 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "LS_BUF_EN";
+	};
+};
+
+/* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/
+/* in case it isn't, wilink8 ends up in one of the test modes that     */
+/* intruces various issues (elp wkaeup timeouts etc.)                  */
+/* On the BBGW this pin is routed through the level shifter (U21) that */
+/* introduces a pullup on the line and wilink8 ends up in a bad state. */
+/* use a gpio hog to force this pin low. An alternative may be adding  */
+/* an external pulldown on U21 pin 4.                                  */
+
+&gpio3 {
+	bt_aud_in {
+		gpio-hog;
+		gpios = <16 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "MCASP0_AHCLKR";
+	};
+};

arch/arm/boot/dts/am335x-bonegreen.dts

@@ -9,45 +9,9 @@
 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
 
 / {
 	model = "TI AM335x BeagleBone Green";
 	compatible = "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
 };
-
-&ldo3_reg {
-	regulator-min-microvolt = <1800000>;
-	regulator-max-microvolt = <1800000>;
-	regulator-always-on;
-};
-
-&mmc1 {
-	vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
-	vmmc-supply = <&vmmcsd_fixed>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_pins>;
-	bus-width = <8>;
-	status = "okay";
-};
-
-&am33xx_pinmux {
-	uart2_pins: uart2_pins {
-		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1)	/* spi0_sclk.uart2_rxd */
-			AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1)	/* spi0_d0.uart2_txd */
-		>;
-	};
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart2_pins>;
-	status = "okay";
-};
-
-&rtc {
-	system-power-controller;
-};

arch/arm/boot/dts/am335x-chilisom.dtsi

@@ -124,6 +124,14 @@
 
 &rtc {
 	system-power-controller;
+
+	pinctrl-0 = <&ext_wakeup>;
+	pinctrl-names = "default";
+
+	ext_wakeup: ext-wakeup {
+		pins = "ext_wakeup0";
+		input-enable;
+	};
 };
 
 /* NAND Flash */

arch/arm/boot/dts/am335x-evm.dts

@@ -25,6 +25,10 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
+	chosen {
+		stdout-path = &uart0;
+	};
+
 	vbat: fixedregulator0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vbat";

arch/arm/boot/dts/am335x-evmsk.dts

@@ -32,6 +32,10 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
+	chosen {
+		stdout-path = &uart0;
+	};
+
 	vbat: fixedregulator0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vbat";

arch/arm/boot/dts/am335x-icev2.dts

@@ -24,6 +24,10 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
+	chosen {
+		stdout-path = &uart3;
+	};
+
 	vbat: fixedregulator0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vbat";

arch/arm/boot/dts/am335x-nano.dts

@@ -249,7 +249,8 @@
 
 	#address-cells = <2>;
 	#size-cells = <1>;
-	ranges = <0 0 0x08000000 0x08000000>;	/* CS0: NOR 128M */
+	ranges = <0 0 0x08000000 0x08000000>,	/* CS0: NOR 128M */
+		 <1 0 0x1c000000 0x01000000>;	/* CS1: FRAM 16M */
 
 	nor@0,0 {
 		reg = <0 0x00000000 0x08000000>;
@@ -342,6 +343,34 @@
 			reg = <0x04000000 0x04000000>; /* 64MB */
 		};
 	};
+
+	fram@1,0 {
+		reg = <1 0x00000000 0x01000000>;
+		bank-width = <2>;
+
+		gpmc,mux-add-data = <2>;
+
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <160>;
+		gpmc,cs-wr-off-ns = <160>;
+		gpmc,adv-on-ns = <10>;
+		gpmc,adv-rd-off-ns = <20>;
+		gpmc,adv-wr-off-ns = <20>;
+		gpmc,oe-on-ns = <30>;
+		gpmc,oe-off-ns = <150>;
+		gpmc,we-on-ns = <30>;
+		gpmc,we-off-ns = <150>;
+		gpmc,rd-cycle-ns = <160>;
+		gpmc,wr-cycle-ns = <160>;
+		gpmc,access-ns = <130>;
+		gpmc,page-burst-access-ns = <10>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		gpmc,cycle2cycle-delay-ns = <10>;
+		gpmc,wr-data-mux-bus-ns = <30>;
+		gpmc,wr-access-ns = <0>;
+	};
 };
 
 &mac {

arch/arm/boot/dts/am335x-pcm-953.dtsi

@@ -0,0 +1,288 @@
+/*
+ * Copyright (C) 2014-2017 Phytec Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *	   Teresa Remmet <t.remmet@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Phytec AM335x PCM-953";
+	compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx";
+
+	/* Power */
+	regulators {
+		vcc3v3: fixedregulator@1 {
+			compatible = "regulator-fixed";
+			regulator-name = "vcc3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+		};
+
+		vcc1v8: fixedregulator@2 {
+			compatible = "regulator-fixed";
+			regulator-name = "vcc1v8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+	};
+
+	/* User IO */
+	user_leds: user_leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds_pins>;
+
+		green {
+			label = "green:user";
+			gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "gpio";
+			default-state = "on";
+		};
+
+		yellow {
+			label = "yellow:user";
+			gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "gpio";
+			default-state = "on";
+		};
+	};
+
+	user_buttons: user_buttons {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_buttons_pins>;
+
+		button@0 {
+			label = "home";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+			wakeup-source;
+		};
+
+		button@1 {
+			label = "menu";
+			linux,code = <KEY_MENU>;
+			gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
+			wakeup-source;
+		};
+
+	};
+};
+
+&am33xx_pinmux {
+	user_buttons_pins: pinmux_user_buttons {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9e4, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* emu0.gpio3_7 */
+			AM33XX_IOPAD(0x9e8, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* emu1.gpio3_8 */
+		>;
+	};
+
+	user_leds_pins: pinmux_user_leds {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x880, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn1.gpio1_30 */
+			AM33XX_IOPAD(0x884, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn2.gpio1_31 */
+		>;
+	};
+};
+
+/* CAN */
+&am33xx_pinmux {
+	dcan1_pins: pinmux_dcan1 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x980, PIN_OUTPUT_PULLUP | MUX_MODE2)	/* uart1_rxd.dcan1_tx_mux2 */
+			AM33XX_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE2)	/* uart1_txd.dcan1_rx_mux2 */
+		>;
+	};
+};
+
+&dcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan1_pins>;
+	status = "okay";
+};
+
+/* Ethernet */
+&am33xx_pinmux {
+	ethernet1_pins: pinmux_ethernet1 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a0.rgmii2_tctl */
+			AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a1.rgmii2_rctl */
+			AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a2.rgmii2_td3 */
+			AM33XX_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a3.rgmii2_td2 */
+			AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a4.rgmii2_td1 */
+			AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a5.rgmii2_td0 */
+			AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a6.rgmii2_tclk */
+			AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a7.rgmii2_rclk */
+			AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a8.rgmii2_rd3 */
+			AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a9.rgmii2_rd2 */
+			AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a10.rgmii2_rd1 */
+			AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a11.rgmii2_rd0 */
+		>;
+	};
+};
+
+&cpsw_emac1 {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	dual_emac_res_vlan = <2>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	phy1: ethernet-phy@2 {
+		reg = <2>;
+
+		/* Register 260 (104h) – RGMII Clock and Control Pad Skew */
+		rxc-skew-ps = <1400>;
+		rxdv-skew-ps = <0>;
+		txc-skew-ps = <1400>;
+		txen-skew-ps = <0>;
+		/* Register 261 (105h) – RGMII RX Data Pad Skew */
+		rxd3-skew-ps = <0>;
+		rxd2-skew-ps = <0>;
+		rxd1-skew-ps = <0>;
+		rxd0-skew-ps = <0>;
+		/* Register 262 (106h) – RGMII TX Data Pad Skew */
+		txd3-skew-ps = <0>;
+		txd2-skew-ps = <0>;
+		txd1-skew-ps = <0>;
+		txd0-skew-ps = <0>;
+	};
+};
+
+&mac {
+	slaves = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
+	dual_emac;
+};
+
+/* Misc */
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cb_gpio_pins>;
+
+	cb_gpio_pins: pinmux_cb_gpio {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart0_ctsn.gpio1_8 */
+			AM33XX_IOPAD(0x96c, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart0_rtsn.gpio1_9 */
+		>;
+	};
+};
+
+/* MMC */
+&am33xx_pinmux {
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat3.mmc0_dat3 */
+			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat2.mmc0_dat2 */
+			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat1.mmc0_dat1 */
+			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat0.mmc0_dat0 */
+			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_clk.mmc0_clk */
+			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_cmd.mmc0_cmd */
+			AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE7)	/* spi0_cs1.mmc0_sdcd */
+		>;
+	};
+};
+
+&mmc1 {
+	vmmc-supply = <&vcc3v3>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+/* UARTs */
+&am33xx_pinmux {
+	uart0_pins: pinmux_uart0 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	uart1_pins: pinmux_uart1 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_rxd.uart1_rxd */
+			AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
+			AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0)		/* uart1_ctsn.uart1_ctsn */
+			AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_rtsn.uart1_rtsn */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE1)	/* mii1_tx_clk.uart2_rxd */
+			AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_rx_clk.uart2_txd */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1)	/* mii1_rxd3.uart3_rxd */
+			AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd2.uart3_txd */
+		>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "okay";
+};
+
+/* USB */
+&cppi41dma {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usb1_phy {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-phycore-rdk.dts

@@ -0,0 +1,27 @@
+/*
+ * Copyright (C) 2014 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am335x-phycore-som.dtsi"
+#include "am335x-pcm-953.dtsi"
+
+/* SoM */
+&i2c_eeprom {
+	status = "okay";
+};
+
+&i2c_rtc {
+	status = "okay";
+};
+
+&serial_flash {
+	status = "okay";
+
+};

arch/arm/boot/dts/am335x-phycore-som.dtsi

@@ -78,7 +78,7 @@
 };
 
 &cpsw_emac0 {
-	phy_id = <&davinci_mdio>, <0>;
+	phy-handle = <&phy0>;
 	phy-mode = "rmii";
 	dual_emac_res_vlan = <1>;
 };
@@ -87,6 +87,10 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mdio_pins>;
 	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
 };
 
 &mac {
@@ -120,6 +124,12 @@
 		reg = <0x2d>;
 	};
 
+	i2c_tmp102: temp@4b {
+		compatible = "ti,tmp102";
+		reg = <0x4b>;
+		status = "disabled";
+	};
+
 	i2c_eeprom: eeprom@52 {
 		compatible = "atmel,24c32";
 		pagesize = <32>;
@@ -201,43 +211,6 @@
 
 		#address-cells = <1>;
 		#size-cells = <1>;
-
-		partition@0 {
-			label = "xload";
-			reg = <0x0 0x20000>;
-		};
-		partition@1 {
-			label = "xload_backup1";
-			reg = <0x20000 0x20000>;
-		};
-		partition@2 {
-			label = "xload_backup2";
-			reg = <0x40000 0x20000>;
-		};
-		partition@3 {
-			label = "xload_backup3";
-			reg = <0x60000 0x20000>;
-		};
-		partition@4 {
-			label = "barebox";
-			reg = <0x80000 0x80000>;
-		};
-		partition@5 {
-			label = "bareboxenv";
-			reg = <0x100000 0x40000>;
-		};
-		partition@6 {
-			label = "oftree";
-			reg = <0x140000 0x40000>;
-		};
-		partition@7 {
-			label = "kernel";
-			reg = <0x180000 0x800000>;
-		};
-		partition@8 {
-			label = "root";
-			reg = <0x980000 0x0>;
-		};
 	};
 };
 
@@ -341,33 +314,12 @@
 	status = "okay";
 
 	serial_flash: m25p80@0 {
-		compatible = "m25p80";
+		compatible = "jedec,spi-nor";
 		spi-max-frequency = <48000000>;
 		reg = <0x0>;
 		m25p,fast-read;
 		status = "disabled";
 		#address-cells = <1>;
 		#size-cells = <1>;
-
-		partition@0 {
-			label = "xload";
-			reg = <0x0 0x20000>;
-		};
-		partition@1 {
-			label = "barebox";
-			reg = <0x20000 0x80000>;
-		};
-		partition@2 {
-			label = "bareboxenv";
-			reg = <0xa0000 0x20000>;
-		};
-		partition@3 {
-			label = "oftree";
-			reg = <0xc0000 0x20000>;
-		};
-		partition@4 {
-			label = "kernel";
-			reg = <0xe0000 0x0>;
-		};
 	};
 };

arch/arm/boot/dts/am335x-sl50.dts

@@ -136,6 +136,13 @@
 		>;
 	};
 
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_rxd.uart1_rxd */
+			AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
+		>;
+	};
+
 	uart4_pins: pinmux_uart4_pins {
 		pinctrl-single,pins = <
 			AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE6)	/* gpmc_wait0.uart4_rxd */
@@ -150,13 +157,6 @@
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
-		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_rxd.i2c1_sda */
-			AM33XX_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_txdi2c1_scl */
-		>;
-	};
-
 	i2c2_pins: pinmux_i2c2_pins {
 		pinctrl-single,pins = <
 			AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_ctsn.i2c2_sda */
@@ -262,6 +262,16 @@
 		>;
 	};
 
+	spi0_pins: pinmux_spi0_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE0)	/* SPI0_MOSI - spi0_d0.spi0_d0 */
+			AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0)	/* SPI0_MISO - spi0_d1.spi0_d1 */
+			AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE0)	/* SPI0_CLK  - spi0_clk.spi0_clk */
+			AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE0)	/* SPI0_CS0 (NBATTSS) - spi0_cs0.spi0_cs0 */
+			AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE0)	/* SPI0_CS1 (FPGA_FLASH_NCS) - spi0_cs1.spi0_cs1 */
+		>;
+	};
+
 	lwb_pins: pinmux_lwb_pins {
 		pinctrl-single,pins = <
 			AM33XX_IOPAD(0x9a4, PIN_OUTPUT | MUX_MODE7)	/* SoundPA_en - mcasp0_fsr.gpio3_19 */
@@ -292,16 +302,22 @@
 		reg = <0x24>;
 	};
 
+	bq32000: rtc@68 {
+		compatible = "ti,bq32000";
+		trickle-resistor-ohms = <1120>;
+		reg = <0x68>;
+	};
+
 	eeprom: eeprom@50 {
 		compatible = "at,24c256";
 		reg = <0x50>;
 	};
-};
 
-&i2c1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
+	gpio_exp: mcp23017@20 {
+		compatible = "microchip,mcp23017";
+		reg = <0x20>;
+	};
+
 };
 
 &i2c2 {
@@ -321,6 +337,16 @@
 		DRVDD-supply = <&ldo4_reg>;
 		DVDD-supply = <&ldo3_reg>;
 	};
+
+	/* Ambient Light Sensor */
+	als: isl29023@44 {
+		compatible = "isil,isl29023";
+		reg = <0x44>;
+	};
+};
+
+&rtc {
+	status = "disabled";
 };
 
 &usb {
@@ -394,12 +420,32 @@
 	pinctrl-0 = <&uart0_pins>;
 };
 
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
 &uart4 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins>;
 };
 
+&spi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+
+	flash: n25q032@1 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q032";
+		reg = <1>;
+		spi-max-frequency = <5000000>;
+	};
+};
+
 #include "tps65217.dtsi"
 
 &tps {

arch/arm/boot/dts/am335x-wega.dtsi

@@ -119,11 +119,17 @@
 };
 
 &cpsw_emac1 {
-	phy_id = <&davinci_mdio>, <1>;
+	phy-handle = <&phy1>;
 	phy-mode = "mii";
 	dual_emac_res_vlan = <2>;
 };
 
+&davinci_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mac {
 	slaves = <2>;
 	pinctrl-names = "default";
@@ -206,7 +212,6 @@
 };
 
 &usb0 {
-	dr_mode = "peripheral";
 	status = "okay";
 };
 

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -23,6 +23,10 @@
 		display0 = &lcd0;
 	};
 
+	chosen {
+		stdout-path = &uart0;
+	};
+
 	evm_v3_3d: fixedregulator-v3_3d {
 		compatible = "regulator-fixed";
 		regulator-name = "evm_v3_3d";

arch/arm/boot/dts/am437x-idk-evm.dts

@@ -18,6 +18,10 @@
 	model = "TI AM437x Industrial Development Kit";
 	compatible = "ti,am437x-idk-evm","ti,am4372","ti,am43";
 
+	chosen {
+		stdout-path = &uart0;
+	};
+
 	v24_0d: fixed-regulator-v24_0d {
 		compatible = "regulator-fixed";
 		regulator-name = "V24_0D";

arch/arm/boot/dts/am437x-sk-evm.dts

@@ -24,6 +24,10 @@
 		display0 = &lcd0;
 	};
 
+	chosen {
+		stdout-path = &uart0;
+	};
+
 	/* fixed 32k external oscillator clock */
 	clk_32k_rtc: clk_32k_rtc {
 		#clock-cells = <0>;

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -24,6 +24,10 @@
 		display0 = &lcd0;
 	};
 
+	chosen {
+		stdout-path = &uart0;
+	};
+
 	vmmcsd_fixed: fixedregulator-sd {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmcsd_fixed";

arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi

@@ -22,6 +22,10 @@
 		display0 = &hdmi0;
 	};
 
+	chosen {
+		stdout-path = &uart3;
+	};
+
 	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x80000000 0x0 0x80000000>;
@@ -421,19 +425,29 @@
 			      <&dra7_pmx_core 0x3f8>;
 };
 
+&davinci_mdio {
+	phy0: ethernet-phy@1 {
+		reg = <1>;
+	};
+
+	phy1: ethernet-phy@2 {
+		reg = <2>;
+	};
+};
+
 &mac {
 	status = "okay";
 	dual_emac;
 };
 
 &cpsw_emac0 {
-	phy_id = <&davinci_mdio>, <1>;
+	phy-handle = <&phy0>;
 	phy-mode = "rgmii";
 	dual_emac_res_vlan = <1>;
 };
 
 &cpsw_emac1 {
-	phy_id = <&davinci_mdio>, <2>;
+	phy-handle = <&phy1>;
 	phy-mode = "rgmii";
 	dual_emac_res_vlan = <2>;
 };

arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts

@@ -22,3 +22,8 @@
 	vmmc-supply = <&vdd_3v3>;
 	vmmc-aux-supply = <&ldo1_reg>;
 };
+
+/* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
+&phy1 {
+	max-speed = <100>;
+};

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -22,3 +22,8 @@
 &mmc1 {
 	vmmc-supply = <&ldo1_reg>;
 };
+
+/* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
+&phy1 {
+	max-speed = <100>;
+};

arch/arm/boot/dts/am57xx-idk-common.dtsi

@@ -14,6 +14,10 @@
 		rtc1 = &rtc;
 	};
 
+	chosen {
+		stdout-path = &uart3;
+	};
+
 	vmain: fixedregulator-vmain {
 		compatible = "regulator-fixed";
 		regulator-name = "VMAIN";

arch/arm/boot/dts/dra7-evm.dts

@@ -21,6 +21,10 @@
 		reg = <0x0 0x80000000 0x0 0x60000000>; /* 1536 MB */
 	};
 
+	chosen {
+		stdout-path = &uart1;
+	};
+
 	evm_3v3_sd: fixedregulator-sd {
 		compatible = "regulator-fixed";
 		regulator-name = "evm_3v3_sd";
@@ -151,204 +155,6 @@
 };
 
 &dra7_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <&vtt_pin>;
-
-	vtt_pin: pinmux_vtt_pin {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37b4, PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */
-		>;
-	};
-
-	i2c1_pins: pinmux_i2c1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda */
-			DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl */
-		>;
-	};
-
-	i2c2_pins: pinmux_i2c2_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
-			DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
-		>;
-	};
-
-	i2c3_pins: pinmux_i2c3_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3688, PIN_INPUT | MUX_MODE9) /* gpio6_14.i2c3_sda */
-			DRA7XX_CORE_IOPAD(0x368c, PIN_INPUT | MUX_MODE9) /* gpio6_15.i2c3_scl */
-		>;
-	};
-
-	mcspi1_pins: pinmux_mcspi1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37a4, PIN_INPUT | MUX_MODE0) /* spi1_sclk */
-			DRA7XX_CORE_IOPAD(0x37a8, PIN_INPUT | MUX_MODE0) /* spi1_d1 */
-			DRA7XX_CORE_IOPAD(0x37ac, PIN_INPUT | MUX_MODE0) /* spi1_d0 */
-			DRA7XX_CORE_IOPAD(0x37b0, PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */
-			DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */
-			DRA7XX_CORE_IOPAD(0x37bc, PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */
-		>;
-	};
-
-	mcspi2_pins: pinmux_mcspi2_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37c0, PIN_INPUT | MUX_MODE0) /* spi2_sclk */
-			DRA7XX_CORE_IOPAD(0x37c4, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
-			DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
-			DRA7XX_CORE_IOPAD(0x37cc, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
-		>;
-	};
-
-	uart1_pins: pinmux_uart1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37e0, PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */
-			DRA7XX_CORE_IOPAD(0x37e4, PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */
-			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT | MUX_MODE3) /* uart1_ctsn */
-			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT | MUX_MODE3) /* uart1_rtsn */
-		>;
-	};
-
-	uart2_pins: pinmux_uart2_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT | MUX_MODE0) /* uart2_rxd */
-			DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT | MUX_MODE0) /* uart2_txd */
-			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT | MUX_MODE0) /* uart2_ctsn */
-			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT | MUX_MODE0) /* uart2_rtsn */
-		>;
-	};
-
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */
-			DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */
-		>;
-	};
-
-	usb1_pins: pinmux_usb1_pins {
-                pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
-                >;
-        };
-
-	usb2_pins: pinmux_usb2_pins {
-                pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */
-                >;
-        };
-
-	nand_flash_x16: nand_flash_x16 {
-		/* On DRA7 EVM, GPMC_WPN and NAND_BOOTn comes from DIP switch
-		 * So NAND flash requires following switch settings:
-		 * SW5.1 (NAND_BOOTn) = ON (LOW)
-		 * SW5.9 (GPMC_WPN) = OFF (HIGH)
-		 */
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad0	*/
-			DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad1	*/
-			DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad2	*/
-			DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad3	*/
-			DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad4	*/
-			DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad5	*/
-			DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad6	*/
-			DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad7	*/
-			DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad8	*/
-			DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad9	*/
-			DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad10	*/
-			DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad11	*/
-			DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad12	*/
-			DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad13	*/
-			DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad14	*/
-			DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad15	*/
-			DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT_PULLUP  | MUX_MODE0)	/* gpmc_wait0	*/
-			DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0)	/* gpmc_wen	*/
-			DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* gpmc_csn0	*/
-			DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0)	/* gpmc_advn_ale */
-			DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0)	/* gpmc_oen_ren	 */
-			DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0)	/* gpmc_be0n_cle */
-		>;
-	};
-
-	cpsw_default: cpsw_default {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txc.rgmii0_txc */
-			DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txctl.rgmii0_txctl */
-			DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_td3.rgmii0_txd3 */
-			DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txd2.rgmii0_txd2 */
-			DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txd1.rgmii0_txd1 */
-			DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txd0.rgmii0_txd0 */
-			DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxc.rgmii0_rxc */
-			DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxctl.rgmii0_rxctl */
-			DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd3.rgmii0_rxd3 */
-			DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd2.rgmii0_rxd2 */
-			DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd1.rgmii0_rxd1 */
-			DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd0.rgmii0_rxd0 */
-
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d12.rgmii1_txc */
-			DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d13.rgmii1_tctl */
-			DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d14.rgmii1_td3 */
-			DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d15.rgmii1_td2 */
-			DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d16.rgmii1_td1 */
-			DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d17.rgmii1_td0 */
-			DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3)	/* vin2a_d18.rgmii1_rclk */
-			DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3)	/* vin2a_d19.rgmii1_rctl */
-			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3)	/* vin2a_d20.rgmii1_rd3 */
-			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3)	/* vin2a_d21.rgmii1_rd2 */
-			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3)	/* vin2a_d22.rgmii1_rd1 */
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3)	/* vin2a_d23.rgmii1_rd0 */
-		>;
-
-	};
-
-	cpsw_sleep: cpsw_sleep {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			DRA7XX_CORE_IOPAD(0x3650, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3654, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3658, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x365c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3660, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3664, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3668, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x366c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3670, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3674, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3678, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x367c, MUX_MODE15)
-
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15)
-		>;
-	};
-
-	davinci_mdio_default: davinci_mdio_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* mdio_d.mdio_d */
-			DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0)	/* mdio_clk.mdio_clk */
-		>;
-	};
-
-	davinci_mdio_sleep: davinci_mdio_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15)
-		>;
-	};
-
 	dcan1_pins_default: dcan1_pins_default {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
@@ -363,36 +169,36 @@
 		>;
 	};
 
-	atl_pins: pinmux_atl_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5)	/* xref_clk1.atl_clk1 */
-			DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5)	/* xref_clk2.atl_clk2 */
-		>;
-	};
-
-	mcasp3_pins: pinmux_mcasp3_pins {
+	mmc1_pins_default: mmc1_pins_default {
 		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_aclkx */
-			DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_fsx */
-			DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_axr0 */
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_axr1 */
+			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
 		>;
 	};
 
-	mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins {
+	mmc2_pins_default: mmc2_pins_default {
 		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3728, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x372c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3730, MUX_MODE15)
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
 		>;
 	};
 };
 
 &i2c1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	clock-frequency = <400000>;
 
 	tps659038: tps659038@58 {
@@ -581,8 +387,6 @@
 
 &i2c2 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
 	clock-frequency = <400000>;
 
 	pcf_hdmi: gpio@26 {
@@ -602,45 +406,35 @@
 
 &i2c3 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c3_pins>;
 	clock-frequency = <400000>;
 };
 
 &mcspi1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi1_pins>;
 };
 
 &mcspi2 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi2_pins>;
 };
 
 &uart1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>;
 	interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
 			      <&dra7_pmx_core 0x3e0>;
 };
 
 &uart2 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart2_pins>;
 };
 
 &uart3 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins>;
 };
 
 &mmc1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_default>;
 	vmmc-supply = <&evm_3v3_sd>;
 	vmmc_aux-supply = <&ldo1_reg>;
 	bus-width = <4>;
@@ -653,6 +447,8 @@
 
 &mmc2 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins_default>;
 	vmmc-supply = <&evm_3v3_sw>;
 	bus-width = <8>;
 };
@@ -732,14 +528,10 @@
 
 &usb1 {
 	dr_mode = "peripheral";
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_pins>;
 };
 
 &usb2 {
 	dr_mode = "host";
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb2_pins>;
 };
 
 &elm {
@@ -747,9 +539,12 @@
 };
 
 &gpmc {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&nand_flash_x16>;
+	/*
+	* For the existing IOdelay configuration via U-Boot we don't
+	* support NAND on dra7-evm. Keep it disabled. Enabling it
+	* requires a different configuration by U-Boot.
+	*/
+	status = "disabled";
 	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
@@ -845,9 +640,6 @@
 
 &mac {
 	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&cpsw_default>;
-	pinctrl-1 = <&cpsw_sleep>;
 	dual_emac;
 };
 
@@ -863,12 +655,6 @@
 	dual_emac_res_vlan = <2>;
 };
 
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_default>;
-	pinctrl-1 = <&davinci_mdio_sleep>;
-};
-
 &dcan1 {
 	status = "ok";
 	pinctrl-names = "default", "sleep", "active";
@@ -878,9 +664,6 @@
 };
 
 &atl {
-	pinctrl-names = "default";
-	pinctrl-0 = <&atl_pins>;
-
 	assigned-clocks = <&abe_dpll_sys_clk_mux>,
 			  <&atl_gfclk_mux>,
 			  <&dpll_abe_ck>,
@@ -899,9 +682,6 @@
 
 &mcasp3 {
 	#sound-dai-cells = <0>;
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&mcasp3_pins>;
-	pinctrl-1 = <&mcasp3_sleep_pins>;
 
 	assigned-clocks = <&mcasp3_ahclkx_mux>;
 	assigned-clock-parents = <&atl_clkin2_ck>;

arch/arm/boot/dts/dra71-evm.dts

@@ -138,6 +138,11 @@
 	};
 };
 
+&pcf_lcd {
+	interrupt-parent = <&gpio7>;
+	interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+};
+
 &pcf_gpio_21 {
 	interrupt-parent = <&gpio7>;
 	interrupts = <31 IRQ_TYPE_EDGE_FALLING>;

arch/arm/boot/dts/dra72-evm-common.dtsi

@@ -18,6 +18,10 @@
 		display0 = &hdmi0;
 	};
 
+	chosen {
+		stdout-path = &uart1;
+	};
+
 	evm_12v0: fixedregulator-evm12v0 {
 		/* main supply */
 		compatible = "regulator-fixed";
@@ -216,6 +220,15 @@
 	status = "okay";
 	clock-frequency = <400000>;
 
+	pcf_lcd: gpio@20 {
+		compatible = "nxp,pcf8575";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
 	pcf_gpio_21: gpio@21 {
 		compatible = "ti,pcf8575", "nxp,pcf8575";
 		reg = <0x21>;
@@ -280,7 +293,12 @@
 };
 
 &gpmc {
-	status = "okay";
+	/*
+	 * For the existing IOdelay configuration via U-Boot we don't
+	 * support NAND on dra72-evm. Keep it disabled. Enabling it
+	 * requires a different configuration by U-Boot.
+	 */
+	status = "disabled";
 	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
 	nand@0,0 {
 		/* To use NAND, DIP switch SW5 must be set like so:

arch/arm/boot/dts/dra72-evm-revc.dts

@@ -68,6 +68,8 @@
 		ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
 		ti,min-output-impedance;
+		interrupt-parent = <&gpio6>;
+		interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
 	};
 
 	dp83867_1: ethernet-phy@3 {
@@ -76,5 +78,7 @@
 		ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
 		ti,min-output-impedance;
+		interrupt-parent = <&gpio6>;
+		interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
 	};
 };

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -27,6 +27,7 @@
 	aliases {
 		display0 = &dvi0;
 		display1 = &tv0;
+		ethernet = &ethernet;
 	};
 
 	leds {
@@ -348,6 +349,21 @@
 
 &usbhsehci {
 	phys = <0 &hsusb2_phy>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub@2 {
+		compatible = "usb424,9514";
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethernet: usbether@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+		};
+	};
 };
 
 &vaux2 {

arch/arm/boot/dts/omap3-igep.dtsi

@@ -126,27 +126,6 @@
 
 		#address-cells = <1>;
 		#size-cells = <1>;
-
-		partition@0 {
-			label = "SPL";
-			reg = <0 0x100000>;
-		};
-		partition@80000 {
-			label = "U-Boot";
-			reg = <0x100000 0x180000>;
-		};
-		partition@1c0000 {
-			label = "Environment";
-			reg = <0x280000 0x100000>;
-		};
-		partition@280000 {
-			label = "Kernel";
-			reg = <0x380000 0x300000>;
-		};
-		partition@780000 {
-			label = "Filesystem";
-			reg = <0x680000 0x1f980000>;
-		};
 	};
 };
 

arch/arm/boot/dts/omap3-n900.dts

@@ -47,7 +47,7 @@
 		compatible = "gpio-leds";
 		heartbeat {
 			label = "debug::sleep";
-			gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;  /* gpio162 */
+			gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;  /* 162 */
 			linux,default-trigger = "default-on";
 			pinctrl-names = "default";
 			pinctrl-0 = <&debug_leds>;
@@ -625,6 +625,7 @@
 		reg = <0x55>;
 	};
 
+	/* Stereo headphone amplifier */
 	tpa6130a2: tpa6130a2@60 {
 		compatible = "ti,tpa6130a2";
 		reg = <0x60>;

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -16,6 +16,7 @@
 	aliases {
 		display0 = &dvi0;
 		display1 = &hdmi0;
+		ethernet = &ethernet;
 	};
 
 	leds: leds {
@@ -520,6 +521,21 @@
 
 &usbhsehci {
 	phys = <&hsusb1_phy>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub@1 {
+		compatible = "usb424,9514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethernet: usbether@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+		};
+	};
 };
 
 &dss {

arch/arm/boot/dts/omap5-igep0050.dts

@@ -19,6 +19,10 @@
 		reg = <0x0 0x80000000 0 0x7f000000>;	/* 2032 MB */
 	};
 
+	aliases {
+		ethernet = &ethernet;
+	};
+
 	gpio_keys {
 		compatible = "gpio-keys";
 		pinctrl-0 = <&power_button_pin>;
@@ -116,3 +120,20 @@
 		OMAP5_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE6)	/* perslimbus2_clock.gpio5_145 */
 	>;
 };
+
+&usbhsehci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub@2 {
+		compatible = "usb424,3503";
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethernet: usbether@3 {
+			compatible = "usb424,7500";
+			reg = <3>;
+		};
+	};
+};

arch/arm/boot/dts/omap5-uevm.dts

@@ -18,6 +18,10 @@
 		reg = <0 0x80000000 0 0x7f000000>; /* 2032 MB */
 	};
 
+	aliases {
+		ethernet = &ethernet;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		led1 {
@@ -164,6 +168,23 @@
 	>;
 };
 
+&usbhsehci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub@2 {
+		compatible = "usb424,3503";
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	ethernet: usbether@3 {
+		compatible = "usb424,9730";
+		reg = <3>;
+	};
+};
+
 &wlcore {
 	compatible = "ti,wl1837";
 };