rsi: configure new boot parameters to device

Boot parameters are changed in new firmware. Also three
new sdio sleep parameters are added for ultra low power
save.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

drivers/net/wireless/rsi/rsi_91x_mgmt.c

@@ -45,10 +45,10 @@ static struct bootup_params boot_params_20 = {
 			}
 		},
 		.switch_clk_g = {
-			.switch_clk_info = cpu_to_le16(BIT(3)),
-			.bbp_lmac_clk_reg_val = cpu_to_le16(0x121),
-			.umac_clock_reg_config = 0x0,
-			.qspi_uart_clock_reg_config = 0x0
+			.switch_clk_info = cpu_to_le16(0xb),
+			.bbp_lmac_clk_reg_val = cpu_to_le16(0x111),
+			.umac_clock_reg_config = cpu_to_le16(0x48),
+			.qspi_uart_clock_reg_config = cpu_to_le16(0x1211)
 		}
 	},
 	{
@@ -106,7 +106,10 @@ static struct bootup_params boot_params_20 = {
 	.wdt_prog_value = 0x0,
 	.wdt_soc_rst_delay = 0x0,
 	.dcdc_operation_mode = 0x0,
-	.soc_reset_wait_cnt = 0x0
+	.soc_reset_wait_cnt = 0x0,
+	.waiting_time_at_fresh_sleep = 0x0,
+	.max_threshold_to_avoid_sleep = 0x0,
+	.beacon_resedue_alg_en = 0,
 };
 
 static struct bootup_params boot_params_40 = {
@@ -139,7 +142,7 @@ static struct bootup_params boot_params_40 = {
 			.switch_clk_info = cpu_to_le16(0x09),
 			.bbp_lmac_clk_reg_val = cpu_to_le16(0x1121),
 			.umac_clock_reg_config = cpu_to_le16(0x48),
-			.qspi_uart_clock_reg_config = 0x0
+			.qspi_uart_clock_reg_config = cpu_to_le16(0x1211)
 		}
 	},
 	{
@@ -197,7 +200,10 @@ static struct bootup_params boot_params_40 = {
 	.wdt_prog_value = 0x0,
 	.wdt_soc_rst_delay = 0x0,
 	.dcdc_operation_mode = 0x0,
-	.soc_reset_wait_cnt = 0x0
+	.soc_reset_wait_cnt = 0x0,
+	.waiting_time_at_fresh_sleep = 0x0,
+	.max_threshold_to_avoid_sleep = 0x0,
+	.beacon_resedue_alg_en = 0,
 };
 
 static u16 mcs[] = {13, 26, 39, 52, 78, 104, 117, 130};

drivers/net/wireless/rsi/rsi_boot_params.h

@@ -24,19 +24,19 @@
 #define WIFI_AFEPLL_CONFIGS              BIT(7)
 #define WIFI_SWITCH_CLK_CONFIGS          BIT(8)
 
-#define TA_PLL_M_VAL_20                  8
-#define TA_PLL_N_VAL_20                  1
+#define TA_PLL_M_VAL_20                  9
+#define TA_PLL_N_VAL_20                  0
 #define TA_PLL_P_VAL_20                  4
 
 #define PLL960_M_VAL_20                  0x14
 #define PLL960_N_VAL_20                  0
 #define PLL960_P_VAL_20                  5
 
-#define UMAC_CLK_40MHZ                   40
+#define UMAC_CLK_40MHZ                   80
 
-#define TA_PLL_M_VAL_40                  46
-#define TA_PLL_N_VAL_40                  3
-#define TA_PLL_P_VAL_40                  3
+#define TA_PLL_M_VAL_40                  9
+#define TA_PLL_N_VAL_40                  0
+#define TA_PLL_P_VAL_40                  4
 
 #define PLL960_M_VAL_40                  0x14
 #define PLL960_N_VAL_40                  0
@@ -122,5 +122,8 @@ struct bootup_params {
 	/* dcdc modes configs */
 	__le32 dcdc_operation_mode;
 	__le32 soc_reset_wait_cnt;
+	__le32 waiting_time_at_fresh_sleep;
+	__le32 max_threshold_to_avoid_sleep;
+	u8 beacon_resedue_alg_en;
 } __packed;
 #endif