Merge tag 'soundwire-streaming' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next

Vinod writes:

soundwire streaming

This contains:
 - Support for SoundWire Streaming
 - Documentation updates for streaming
 - Cadence and Intel driver updates for streaming
 - ASoC API for programming soundwire stream

Documentation/driver-api/soundwire/error_handling.rst

@@ -0,0 +1,65 @@
+========================
+SoundWire Error Handling
+========================
+
+The SoundWire PHY was designed with care and errors on the bus are going to
+be very unlikely, and if they happen it should be limited to single bit
+errors. Examples of this design can be found in the synchronization
+mechanism (sync loss after two errors) and short CRCs used for the Bulk
+Register Access.
+
+The errors can be detected with multiple mechanisms:
+
+1. Bus clash or parity errors: This mechanism relies on low-level detectors
+   that are independent of the payload and usages, and they cover both control
+   and audio data. The current implementation only logs such errors.
+   Improvements could be invalidating an entire programming sequence and
+   restarting from a known position. In the case of such errors outside of a
+   control/command sequence, there is no concealment or recovery for audio
+   data enabled by the SoundWire protocol, the location of the error will also
+   impact its audibility (most-significant bits will be more impacted in PCM),
+   and after a number of such errors are detected the bus might be reset. Note
+   that bus clashes due to programming errors (two streams using the same bit
+   slots) or electrical issues during the transmit/receive transition cannot
+   be distinguished, although a recurring bus clash when audio is enabled is a
+   indication of a bus allocation issue. The interrupt mechanism can also help
+   identify Slaves which detected a Bus Clash or a Parity Error, but they may
+   not be responsible for the errors so resetting them individually is not a
+   viable recovery strategy.
+
+2. Command status: Each command is associated with a status, which only
+   covers transmission of the data between devices. The ACK status indicates
+   that the command was received and will be executed by the end of the
+   current frame. A NAK indicates that the command was in error and will not
+   be applied. In case of a bad programming (command sent to non-existent
+   Slave or to a non-implemented register) or electrical issue, no response
+   signals the command was ignored. Some Master implementations allow for a
+   command to be retransmitted several times.  If the retransmission fails,
+   backtracking and restarting the entire programming sequence might be a
+   solution. Alternatively some implementations might directly issue a bus
+   reset and re-enumerate all devices.
+
+3. Timeouts: In a number of cases such as ChannelPrepare or
+   ClockStopPrepare, the bus driver is supposed to poll a register field until
+   it transitions to a NotFinished value of zero. The MIPI SoundWire spec 1.1
+   does not define timeouts but the MIPI SoundWire DisCo document adds
+   recommendation on timeouts. If such configurations do not complete, the
+   driver will return a -ETIMEOUT. Such timeouts are symptoms of a faulty
+   Slave device and are likely impossible to recover from.
+
+Errors during global reconfiguration sequences are extremely difficult to
+handle:
+
+1. BankSwitch: An error during the last command issuing a BankSwitch is
+   difficult to backtrack from. Retransmitting the Bank Switch command may be
+   possible in a single segment setup, but this can lead to synchronization
+   problems when enabling multiple bus segments (a command with side effects
+   such as frame reconfiguration would be handled at different times). A global
+   hard-reset might be the best solution.
+
+Note that SoundWire does not provide a mechanism to detect illegal values
+written in valid registers. In a number of cases the standard even mentions
+that the Slave might behave in implementation-defined ways. The bus
+implementation does not provide a recovery mechanism for such errors, Slave
+or Master driver implementers are responsible for writing valid values in
+valid registers and implement additional range checking if needed.

Documentation/driver-api/soundwire/index.rst

@@ -6,6 +6,9 @@ SoundWire Documentation
    :maxdepth: 1
 
    summary
+   stream
+   error_handling
+   locking
 
 .. only::  subproject
 

Documentation/driver-api/soundwire/locking.rst

@@ -0,0 +1,106 @@
+=================
+SoundWire Locking
+=================
+
+This document explains locking mechanism of the SoundWire Bus. Bus uses
+following locks in order to avoid race conditions in Bus operations on
+shared resources.
+
+  - Bus lock
+
+  - Message lock
+
+Bus lock
+========
+
+SoundWire Bus lock is a mutex and is part of Bus data structure
+(sdw_bus) which is used for every Bus instance. This lock is used to
+serialize each of the following operations(s) within SoundWire Bus instance.
+
+  - Addition and removal of Slave(s), changing Slave status.
+
+  - Prepare, Enable, Disable and De-prepare stream operations.
+
+  - Access of Stream data structure.
+
+Message lock
+============
+
+SoundWire message transfer lock. This mutex is part of
+Bus data structure (sdw_bus). This lock is used to serialize the message
+transfers (read/write) within a SoundWire Bus instance.
+
+Below examples show how locks are acquired.
+
+Example 1
+---------
+
+Message transfer.
+
+  1. For every message transfer
+
+     a. Acquire Message lock.
+
+     b. Transfer message (Read/Write) to Slave1 or broadcast message on
+        Bus in case of bank switch.
+
+     c. Release Message lock ::
+
+	+----------+                    +---------+
+	|          |                    |         |
+	|   Bus    |                    | Master  |
+	|          |                    | Driver  |
+	|          |                    |         |
+	+----+-----+                    +----+----+
+	     |                               |
+	     |     bus->ops->xfer_msg()      |
+	     <-------------------------------+   a. Acquire Message lock
+	     |                               |   b. Transfer message
+	     |                               |
+	     +------------------------------->   c. Release Message lock
+	     |    return success/error       |   d. Return success/error
+	     |                               |
+	     +                               +
+
+Example 2
+---------
+
+Prepare operation.
+
+  1. Acquire lock for Bus instance associated with Master 1.
+
+  2. For every message transfer in Prepare operation
+
+     a. Acquire Message lock.
+
+     b. Transfer message (Read/Write) to Slave1 or broadcast message on
+        Bus in case of bank switch.
+
+     c. Release Message lock.
+
+  3. Release lock for Bus instance associated with Master 1 ::
+
+	+----------+                    +---------+
+	|          |                    |         |
+	|   Bus    |                    | Master  |
+	|          |                    | Driver  |
+	|          |                    |         |
+	+----+-----+                    +----+----+
+	     |                               |
+	     |    sdw_prepare_stream()       |
+	     <-------------------------------+   1. Acquire bus lock
+	     |                               |   2. Perform stream prepare
+	     |                               |
+	     |                               |
+	     |     bus->ops->xfer_msg()      |
+	     <-------------------------------+   a. Acquire Message lock
+	     |                               |   b. Transfer message
+	     |                               |
+	     +------------------------------->   c. Release Message lock
+	     |    return success/error       |   d. Return success/error
+	     |                               |
+	     |                               |
+	     |    return success/error       |   3. Release bus lock
+	     +------------------------------->   4. Return success/error
+	     |                               |
+	     +                               +

Documentation/driver-api/soundwire/stream.rst

@@ -0,0 +1,372 @@
+=========================
+Audio Stream in SoundWire
+=========================
+
+An audio stream is a logical or virtual connection created between
+
+  (1) System memory buffer(s) and Codec(s)
+
+  (2) DSP memory buffer(s) and Codec(s)
+
+  (3) FIFO(s) and Codec(s)
+
+  (4) Codec(s) and Codec(s)
+
+which is typically driven by a DMA(s) channel through the data link. An
+audio stream contains one or more channels of data. All channels within
+stream must have same sample rate and same sample size.
+
+Assume a stream with two channels (Left & Right) is opened using SoundWire
+interface. Below are some ways a stream can be represented in SoundWire.
+
+Stream Sample in memory (System memory, DSP memory or FIFOs) ::
+
+	-------------------------
+	| L | R | L | R | L | R |
+	-------------------------
+
+Example 1: Stereo Stream with L and R channels is rendered from Master to
+Slave. Both Master and Slave is using single port. ::
+
+	+---------------+                    Clock Signal  +---------------+
+	|    Master     +----------------------------------+     Slave     |
+	|   Interface   |                                  |   Interface   |
+	|               |                                  |       1       |
+	|               |                     Data Signal  |               |
+	|    L  +  R    +----------------------------------+    L  +  R    |
+	|     (Data)    |     Data Direction               |     (Data)    |
+	+---------------+  +----------------------->       +---------------+
+
+
+Example 2: Stereo Stream with L and R channels is captured from Slave to
+Master. Both Master and Slave is using single port. ::
+
+
+	+---------------+                    Clock Signal  +---------------+
+	|    Master     +----------------------------------+     Slave     |
+	|   Interface   |                                  |   Interface   |
+	|               |                                  |       1       |
+	|               |                     Data Signal  |               |
+	|    L  +  R    +----------------------------------+    L  +  R    |
+	|     (Data)    |     Data Direction               |     (Data)    |
+	+---------------+  <-----------------------+       +---------------+
+
+
+Example 3: Stereo Stream with L and R channels is rendered by Master. Each
+of the L and R channel is received by two different Slaves. Master and both
+Slaves are using single port. ::
+
+	+---------------+                    Clock Signal  +---------------+
+	|    Master     +---------+------------------------+     Slave     |
+	|   Interface   |         |                        |   Interface   |
+	|               |         |                        |       1       |
+	|               |         |           Data Signal  |               |
+	|    L  +  R    +---+------------------------------+       L       |
+	|     (Data)    |   |     |    Data Direction      |     (Data)    |
+	+---------------+   |     |   +------------->      +---------------+
+	                    |     |
+	                    |     |
+	                    |     |                        +---------------+
+	                    |     +----------------------> |     Slave     |
+	                    |                              |   Interface   |
+	                    |                              |       2       |
+	                    |                              |               |
+	                    +----------------------------> |       R       |
+	                                                   |     (Data)    |
+	                                                   +---------------+
+
+
+Example 4: Stereo Stream with L and R channel is rendered by two different
+Ports of the Master and is received by only single Port of the Slave
+interface. ::
+
+	+--------------------+
+	|                    |
+	|     +--------------+                             +----------------+
+	|     |             ||                             |                |
+	|     |  Data Port  ||  L Channel                  |                |
+	|     |      1      |------------+                 |                |
+	|     |  L Channel  ||           |                 +-----+----+     |
+	|     |   (Data)    ||           |   L + R Channel ||    Data |     |
+	| Master  +----------+           | +---+---------> ||    Port |     |
+	| Interface          |           |                 ||     1   |     |
+	|     +--------------+           |                 ||         |     |
+	|     |             ||           |                 +----------+     |
+	|     |  Data Port  |------------+                 |                |
+	|     |      2      ||  R Channel                  |     Slave      |
+	|     |  R Channel  ||                             |   Interface    |
+	|     |   (Data)    ||                             |       1        |
+	|     +--------------+         Clock Signal        |     L  +  R    |
+	|                    +---------------------------> |      (Data)    |
+	+--------------------+                             |                |
+							   +----------------+
+
+SoundWire Stream Management flow
+================================
+
+Stream definitions
+------------------
+
+  (1) Current stream: This is classified as the stream on which operation has
+      to be performed like prepare, enable, disable, de-prepare etc.
+
+  (2) Active stream: This is classified as the stream which is already active
+      on Bus other than current stream. There can be multiple active streams
+      on the Bus.
+
+SoundWire Bus manages stream operations for each stream getting
+rendered/captured on the SoundWire Bus. This section explains Bus operations
+done for each of the stream allocated/released on Bus. Following are the
+stream states maintained by the Bus for each of the audio stream.
+
+
+SoundWire stream states
+-----------------------
+
+Below shows the SoundWire stream states and state transition diagram. ::
+
+	+-----------+     +------------+     +----------+     +----------+
+	| ALLOCATED +---->| CONFIGURED +---->| PREPARED +---->| ENABLED  |
+	|   STATE   |     |    STATE   |     |  STATE   |     |  STATE   |
+	+-----------+     +------------+     +----------+     +----+-----+
+	                                                           ^
+	                                                           |
+	                                                           |
+	                                                           v
+	         +----------+           +------------+        +----+-----+
+	         | RELEASED |<----------+ DEPREPARED |<-------+ DISABLED |
+	         |  STATE   |           |   STATE    |        |  STATE   |
+	         +----------+           +------------+        +----------+
+
+NOTE: State transition between prepare and deprepare is supported in Spec
+but not in the software (subsystem)
+
+NOTE2: Stream state transition checks need to be handled by caller
+framework, for example ALSA/ASoC. No checks for stream transition exist in
+SoundWire subsystem.
+
+Stream State Operations
+-----------------------
+
+Below section explains the operations done by the Bus on Master(s) and
+Slave(s) as part of stream state transitions.
+
+SDW_STREAM_ALLOCATED
+~~~~~~~~~~~~~~~~~~~~
+
+Allocation state for stream. This is the entry state
+of the stream. Operations performed before entering in this state:
+
+  (1) A stream runtime is allocated for the stream. This stream
+      runtime is used as a reference for all the operations performed
+      on the stream.
+
+  (2) The resources required for holding stream runtime information are
+      allocated and initialized. This holds all stream related information
+      such as stream type (PCM/PDM) and parameters, Master and Slave
+      interface associated with the stream, stream state etc.
+
+After all above operations are successful, stream state is set to
+``SDW_STREAM_ALLOCATED``.
+
+Bus implements below API for allocate a stream which needs to be called once
+per stream. From ASoC DPCM framework, this stream state maybe linked to
+.startup() operation.
+
+  .. code-block:: c
+  int sdw_alloc_stream(char * stream_name);
+
+
+SDW_STREAM_CONFIGURED
+~~~~~~~~~~~~~~~~~~~~~
+
+Configuration state of stream. Operations performed before entering in
+this state:
+
+  (1) The resources allocated for stream information in SDW_STREAM_ALLOCATED
+      state are updated here. This includes stream parameters, Master(s)
+      and Slave(s) runtime information associated with current stream.
+
+  (2) All the Master(s) and Slave(s) associated with current stream provide
+      the port information to Bus which includes port numbers allocated by
+      Master(s) and Slave(s) for current stream and their channel mask.
+
+After all above operations are successful, stream state is set to
+``SDW_STREAM_CONFIGURED``.
+
+Bus implements below APIs for CONFIG state which needs to be called by
+the respective Master(s) and Slave(s) associated with stream. These APIs can
+only be invoked once by respective Master(s) and Slave(s). From ASoC DPCM
+framework, this stream state is linked to .hw_params() operation.
+
+  .. code-block:: c
+  int sdw_stream_add_master(struct sdw_bus * bus,
+		struct sdw_stream_config * stream_config,
+		struct sdw_ports_config * ports_config,
+		struct sdw_stream_runtime * stream);
+
+  int sdw_stream_add_slave(struct sdw_slave * slave,
+		struct sdw_stream_config * stream_config,
+		struct sdw_ports_config * ports_config,
+		struct sdw_stream_runtime * stream);
+
+
+SDW_STREAM_PREPARED
+~~~~~~~~~~~~~~~~~~~
+
+Prepare state of stream. Operations performed before entering in this state:
+
+  (1) Bus parameters such as bandwidth, frame shape, clock frequency,
+      are computed based on current stream as well as already active
+      stream(s) on Bus. Re-computation is required to accommodate current
+      stream on the Bus.
+
+  (2) Transport and port parameters of all Master(s) and Slave(s) port(s) are
+      computed for the current as well as already active stream based on frame
+      shape and clock frequency computed in step 1.
+
+  (3) Computed Bus and transport parameters are programmed in Master(s) and
+      Slave(s) registers. The banked registers programming is done on the
+      alternate bank (bank currently unused). Port(s) are enabled for the
+      already active stream(s) on the alternate bank (bank currently unused).
+      This is done in order to not disrupt already active stream(s).
+
+  (4) Once all the values are programmed, Bus initiates switch to alternate
+      bank where all new values programmed gets into effect.
+
+  (5) Ports of Master(s) and Slave(s) for current stream are prepared by
+      programming PrepareCtrl register.
+
+After all above operations are successful, stream state is set to
+``SDW_STREAM_PREPARED``.
+
+Bus implements below API for PREPARE state which needs to be called once per
+stream. From ASoC DPCM framework, this stream state is linked to
+.prepare() operation.
+
+  .. code-block:: c
+  int sdw_prepare_stream(struct sdw_stream_runtime * stream);
+
+
+SDW_STREAM_ENABLED
+~~~~~~~~~~~~~~~~~~
+
+Enable state of stream. The data port(s) are enabled upon entering this state.
+Operations performed before entering in this state:
+
+  (1) All the values computed in SDW_STREAM_PREPARED state are programmed
+      in alternate bank (bank currently unused). It includes programming of
+      already active stream(s) as well.
+
+  (2) All the Master(s) and Slave(s) port(s) for the current stream are
+      enabled on alternate bank (bank currently unused) by programming
+      ChannelEn register.
+
+  (3) Once all the values are programmed, Bus initiates switch to alternate
+      bank where all new values programmed gets into effect and port(s)
+      associated with current stream are enabled.
+
+After all above operations are successful, stream state is set to
+``SDW_STREAM_ENABLED``.
+
+Bus implements below API for ENABLE state which needs to be called once per
+stream. From ASoC DPCM framework, this stream state is linked to
+.trigger() start operation.
+
+  .. code-block:: c
+  int sdw_enable_stream(struct sdw_stream_runtime * stream);
+
+SDW_STREAM_DISABLED
+~~~~~~~~~~~~~~~~~~~
+
+Disable state of stream. The data port(s) are disabled upon exiting this state.
+Operations performed before entering in this state:
+
+  (1) All the Master(s) and Slave(s) port(s) for the current stream are
+      disabled on alternate bank (bank currently unused) by programming
+      ChannelEn register.
+
+  (2) All the current configuration of Bus and active stream(s) are programmed
+      into alternate bank (bank currently unused).
+
+  (3) Once all the values are programmed, Bus initiates switch to alternate
+      bank where all new values programmed gets into effect and port(s) associated
+      with current stream are disabled.
+
+After all above operations are successful, stream state is set to
+``SDW_STREAM_DISABLED``.
+
+Bus implements below API for DISABLED state which needs to be called once
+per stream. From ASoC DPCM framework, this stream state is linked to
+.trigger() stop operation.
+
+  .. code-block:: c
+  int sdw_disable_stream(struct sdw_stream_runtime * stream);
+
+
+SDW_STREAM_DEPREPARED
+~~~~~~~~~~~~~~~~~~~~~
+
+De-prepare state of stream. Operations performed before entering in this
+state:
+
+  (1) All the port(s) of Master(s) and Slave(s) for current stream are
+      de-prepared by programming PrepareCtrl register.
+
+  (2) The payload bandwidth of current stream is reduced from the total
+      bandwidth requirement of bus and new parameters calculated and
+      applied by performing bank switch etc.
+
+After all above operations are successful, stream state is set to
+``SDW_STREAM_DEPREPARED``.
+
+Bus implements below API for DEPREPARED state which needs to be called once
+per stream. From ASoC DPCM framework, this stream state is linked to
+.trigger() stop operation.
+
+  .. code-block:: c
+  int sdw_deprepare_stream(struct sdw_stream_runtime * stream);
+
+
+SDW_STREAM_RELEASED
+~~~~~~~~~~~~~~~~~~~
+
+Release state of stream. Operations performed before entering in this state:
+
+  (1) Release port resources for all Master(s) and Slave(s) port(s)
+      associated with current stream.
+
+  (2) Release Master(s) and Slave(s) runtime resources associated with
+      current stream.
+
+  (3) Release stream runtime resources associated with current stream.
+
+After all above operations are successful, stream state is set to
+``SDW_STREAM_RELEASED``.
+
+Bus implements below APIs for RELEASE state which needs to be called by
+all the Master(s) and Slave(s) associated with stream. From ASoC DPCM
+framework, this stream state is linked to .hw_free() operation.
+
+  .. code-block:: c
+  int sdw_stream_remove_master(struct sdw_bus * bus,
+		struct sdw_stream_runtime * stream);
+  int sdw_stream_remove_slave(struct sdw_slave * slave,
+		struct sdw_stream_runtime * stream);
+
+
+The .shutdown() ASoC DPCM operation calls below Bus API to release
+stream assigned as part of ALLOCATED state.
+
+In .shutdown() the data structure maintaining stream state are freed up.
+
+  .. code-block:: c
+  void sdw_release_stream(struct sdw_stream_runtime * stream);
+
+Not Supported
+=============
+
+1. A single port with multiple channels supported cannot be used between two
+streams or across stream. For example a port with 4 channels cannot be used
+to handle 2 independent stereo streams even though it's possible in theory
+in SoundWire.

MAINTAINERS

@@ -13115,7 +13115,7 @@ F:	include/uapi/sound/
 F:	sound/
 
 SOUND - COMPRESSED AUDIO
-M:	Vinod Koul <vinod.koul@intel.com>
+M:	Vinod Koul <vkoul@kernel.org>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git
 S:	Supported

drivers/soundwire/Kconfig

@@ -27,7 +27,7 @@ config SOUNDWIRE_INTEL
 	tristate "Intel SoundWire Master driver"
 	select SOUNDWIRE_CADENCE
 	select SOUNDWIRE_BUS
-	depends on X86 && ACPI
+	depends on X86 && ACPI && SND_SOC
 	---help---
 	  SoundWire Intel Master driver.
 	  If you have an Intel platform which has a SoundWire Master then

drivers/soundwire/Makefile

@@ -3,7 +3,7 @@
 #
 
 #Bus Objs
-soundwire-bus-objs := bus_type.o bus.o slave.o mipi_disco.o
+soundwire-bus-objs := bus_type.o bus.o slave.o mipi_disco.o stream.o
 obj-$(CONFIG_SOUNDWIRE_BUS) += soundwire-bus.o
 
 #Cadence Objs

drivers/soundwire/bus.c

@@ -17,6 +17,7 @@
  */
 int sdw_add_bus_master(struct sdw_bus *bus)
 {
+	struct sdw_master_prop *prop = NULL;
 	int ret;
 
 	if (!bus->dev) {
@@ -32,6 +33,7 @@ int sdw_add_bus_master(struct sdw_bus *bus)
 	mutex_init(&bus->msg_lock);
 	mutex_init(&bus->bus_lock);
 	INIT_LIST_HEAD(&bus->slaves);
+	INIT_LIST_HEAD(&bus->m_rt_list);
 
 	if (bus->ops->read_prop) {
 		ret = bus->ops->read_prop(bus);
@@ -77,6 +79,21 @@ int sdw_add_bus_master(struct sdw_bus *bus)
 		return ret;
 	}
 
+	/*
+	 * Initialize clock values based on Master properties. The max
+	 * frequency is read from max_freq property. Current assumption
+	 * is that the bus will start at highest clock frequency when
+	 * powered on.
+	 *
+	 * Default active bank will be 0 as out of reset the Slaves have
+	 * to start with bank 0 (Table 40 of Spec)
+	 */
+	prop = &bus->prop;
+	bus->params.max_dr_freq = prop->max_freq * SDW_DOUBLE_RATE_FACTOR;
+	bus->params.curr_dr_freq = bus->params.max_dr_freq;
+	bus->params.curr_bank = SDW_BANK0;
+	bus->params.next_bank = SDW_BANK1;
+
 	return 0;
 }
 EXPORT_SYMBOL(sdw_add_bus_master);
@@ -576,6 +593,32 @@ static void sdw_modify_slave_status(struct sdw_slave *slave,
 	mutex_unlock(&slave->bus->bus_lock);
 }
 
+int sdw_configure_dpn_intr(struct sdw_slave *slave,
+			int port, bool enable, int mask)
+{
+	u32 addr;
+	int ret;
+	u8 val = 0;
+
+	addr = SDW_DPN_INTMASK(port);
+
+	/* Set/Clear port ready interrupt mask */
+	if (enable) {
+		val |= mask;
+		val |= SDW_DPN_INT_PORT_READY;
+	} else {
+		val &= ~(mask);
+		val &= ~SDW_DPN_INT_PORT_READY;
+	}
+
+	ret = sdw_update(slave, addr, (mask | SDW_DPN_INT_PORT_READY), val);
+	if (ret < 0)
+		dev_err(slave->bus->dev,
+				"SDW_DPN_INTMASK write failed:%d", val);
+
+	return ret;
+}
+
 static int sdw_initialize_slave(struct sdw_slave *slave)
 {
 	struct sdw_slave_prop *prop = &slave->prop;

drivers/soundwire/bus.h

@@ -45,6 +45,78 @@ struct sdw_msg {
 	bool page;
 };
 
+#define SDW_DOUBLE_RATE_FACTOR		2
+
+extern int rows[SDW_FRAME_ROWS];
+extern int cols[SDW_FRAME_COLS];
+
+/**
+ * sdw_port_runtime: Runtime port parameters for Master or Slave
+ *
+ * @num: Port number. For audio streams, valid port number ranges from
+ * [1,14]
+ * @ch_mask: Channel mask
+ * @transport_params: Transport parameters
+ * @port_params: Port parameters
+ * @port_node: List node for Master or Slave port_list
+ *
+ * SoundWire spec has no mention of ports for Master interface but the
+ * concept is logically extended.
+ */
+struct sdw_port_runtime {
+	int num;
+	int ch_mask;
+	struct sdw_transport_params transport_params;
+	struct sdw_port_params port_params;
+	struct list_head port_node;
+};
+
+/**
+ * sdw_slave_runtime: Runtime Stream parameters for Slave
+ *
+ * @slave: Slave handle
+ * @direction: Data direction for Slave
+ * @ch_count: Number of channels handled by the Slave for
+ * this stream
+ * @m_rt_node: sdw_master_runtime list node
+ * @port_list: List of Slave Ports configured for this stream
+ */
+struct sdw_slave_runtime {
+	struct sdw_slave *slave;
+	enum sdw_data_direction direction;
+	unsigned int ch_count;
+	struct list_head m_rt_node;
+	struct list_head port_list;
+};
+
+/**
+ * sdw_master_runtime: Runtime stream parameters for Master
+ *
+ * @bus: Bus handle
+ * @stream: Stream runtime handle
+ * @direction: Data direction for Master
+ * @ch_count: Number of channels handled by the Master for
+ * this stream, can be zero.
+ * @slave_rt_list: Slave runtime list
+ * @port_list: List of Master Ports configured for this stream, can be zero.
+ * @bus_node: sdw_bus m_rt_list node
+ */
+struct sdw_master_runtime {
+	struct sdw_bus *bus;
+	struct sdw_stream_runtime *stream;
+	enum sdw_data_direction direction;
+	unsigned int ch_count;
+	struct list_head slave_rt_list;
+	struct list_head port_list;
+	struct list_head bus_node;
+};
+
+struct sdw_dpn_prop *sdw_get_slave_dpn_prop(struct sdw_slave *slave,
+				enum sdw_data_direction direction,
+				unsigned int port_num);
+int sdw_configure_dpn_intr(struct sdw_slave *slave, int port,
+					bool enable, int mask);
+
 int sdw_transfer(struct sdw_bus *bus, struct sdw_msg *msg);
 int sdw_transfer_defer(struct sdw_bus *bus, struct sdw_msg *msg,
 				struct sdw_defer *defer);

drivers/soundwire/cadence_master.c

@@ -13,6 +13,8 @@
 #include <linux/mod_devicetable.h>
 #include <linux/soundwire/sdw_registers.h>
 #include <linux/soundwire/sdw.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
 #include "bus.h"
 #include "cadence_master.h"
 
@@ -396,7 +398,7 @@ static int cdns_prep_msg(struct sdw_cdns *cdns, struct sdw_msg *msg, int *cmd)
 	return 0;
 }
 
-static enum sdw_command_response
+enum sdw_command_response
 cdns_xfer_msg(struct sdw_bus *bus, struct sdw_msg *msg)
 {
 	struct sdw_cdns *cdns = bus_to_cdns(bus);
@@ -422,8 +424,9 @@ cdns_xfer_msg(struct sdw_bus *bus, struct sdw_msg *msg)
 exit:
 	return ret;
 }
+EXPORT_SYMBOL(cdns_xfer_msg);
 
-static enum sdw_command_response
+enum sdw_command_response
 cdns_xfer_msg_defer(struct sdw_bus *bus,
 		struct sdw_msg *msg, struct sdw_defer *defer)
 {
@@ -443,8 +446,9 @@ cdns_xfer_msg_defer(struct sdw_bus *bus,
 
 	return _cdns_xfer_msg(cdns, msg, cmd, 0, msg->len, true);
 }
+EXPORT_SYMBOL(cdns_xfer_msg_defer);
 
-static enum sdw_command_response
+enum sdw_command_response
 cdns_reset_page_addr(struct sdw_bus *bus, unsigned int dev_num)
 {
 	struct sdw_cdns *cdns = bus_to_cdns(bus);
@@ -456,6 +460,7 @@ cdns_reset_page_addr(struct sdw_bus *bus, unsigned int dev_num)
 
 	return cdns_program_scp_addr(cdns, &msg);
 }
+EXPORT_SYMBOL(cdns_reset_page_addr);
 
 /*
  * IRQ handling
@@ -666,6 +671,120 @@ int sdw_cdns_enable_interrupt(struct sdw_cdns *cdns)
 }
 EXPORT_SYMBOL(sdw_cdns_enable_interrupt);
 
+static int cdns_allocate_pdi(struct sdw_cdns *cdns,
+			struct sdw_cdns_pdi **stream,
+			u32 num, u32 pdi_offset)
+{
+	struct sdw_cdns_pdi *pdi;
+	int i;
+
+	if (!num)
+		return 0;
+
+	pdi = devm_kcalloc(cdns->dev, num, sizeof(*pdi), GFP_KERNEL);
+	if (!pdi)
+		return -ENOMEM;
+
+	for (i = 0; i < num; i++) {
+		pdi[i].num = i + pdi_offset;
+		pdi[i].assigned = false;
+	}
+
+	*stream = pdi;
+	return 0;
+}
+
+/**
+ * sdw_cdns_pdi_init() - PDI initialization routine
+ *
+ * @cdns: Cadence instance
+ * @config: Stream configurations
+ */
+int sdw_cdns_pdi_init(struct sdw_cdns *cdns,
+			struct sdw_cdns_stream_config config)
+{
+	struct sdw_cdns_streams *stream;
+	int offset, i, ret;
+
+	cdns->pcm.num_bd = config.pcm_bd;
+	cdns->pcm.num_in = config.pcm_in;
+	cdns->pcm.num_out = config.pcm_out;
+	cdns->pdm.num_bd = config.pdm_bd;
+	cdns->pdm.num_in = config.pdm_in;
+	cdns->pdm.num_out = config.pdm_out;
+
+	/* Allocate PDIs for PCMs */
+	stream = &cdns->pcm;
+
+	/* First two PDIs are reserved for bulk transfers */
+	stream->num_bd -= CDNS_PCM_PDI_OFFSET;
+	offset = CDNS_PCM_PDI_OFFSET;
+
+	ret = cdns_allocate_pdi(cdns, &stream->bd,
+				stream->num_bd, offset);
+	if (ret)
+		return ret;
+
+	offset += stream->num_bd;
+
+	ret = cdns_allocate_pdi(cdns, &stream->in,
+				stream->num_in, offset);
+	if (ret)
+		return ret;
+
+	offset += stream->num_in;
+
+	ret = cdns_allocate_pdi(cdns, &stream->out,
+				stream->num_out, offset);
+	if (ret)
+		return ret;
+
+	/* Update total number of PCM PDIs */
+	stream->num_pdi = stream->num_bd + stream->num_in + stream->num_out;
+	cdns->num_ports = stream->num_pdi;
+
+	/* Allocate PDIs for PDMs */
+	stream = &cdns->pdm;
+	offset = CDNS_PDM_PDI_OFFSET;
+	ret = cdns_allocate_pdi(cdns, &stream->bd,
+				stream->num_bd, offset);
+	if (ret)
+		return ret;
+
+	offset += stream->num_bd;
+
+	ret = cdns_allocate_pdi(cdns, &stream->in,
+				stream->num_in, offset);
+	if (ret)
+		return ret;
+
+	offset += stream->num_in;
+
+	ret = cdns_allocate_pdi(cdns, &stream->out,
+				stream->num_out, offset);
+	if (ret)
+		return ret;
+
+	/* Update total number of PDM PDIs */
+	stream->num_pdi = stream->num_bd + stream->num_in + stream->num_out;
+	cdns->num_ports += stream->num_pdi;
+
+	cdns->ports = devm_kcalloc(cdns->dev, cdns->num_ports,
+				sizeof(*cdns->ports), GFP_KERNEL);
+	if (!cdns->ports) {
+		ret = -ENOMEM;
+		return ret;
+	}
+
+	for (i = 0; i < cdns->num_ports; i++) {
+		cdns->ports[i].assigned = false;
+		cdns->ports[i].num = i + 1; /* Port 0 reserved for bulk */
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(sdw_cdns_pdi_init);
+
 /**
  * sdw_cdns_init() - Cadence initialization
  * @cdns: Cadence instance
@@ -727,13 +846,133 @@ int sdw_cdns_init(struct sdw_cdns *cdns)
 }
 EXPORT_SYMBOL(sdw_cdns_init);
 
-struct sdw_master_ops sdw_cdns_master_ops = {
-	.read_prop = sdw_master_read_prop,
-	.xfer_msg = cdns_xfer_msg,
-	.xfer_msg_defer = cdns_xfer_msg_defer,
-	.reset_page_addr = cdns_reset_page_addr,
+int cdns_bus_conf(struct sdw_bus *bus, struct sdw_bus_params *params)
+{
+	struct sdw_cdns *cdns = bus_to_cdns(bus);
+	int mcp_clkctrl_off, mcp_clkctrl;
+	int divider;
+
+	if (!params->curr_dr_freq) {
+		dev_err(cdns->dev, "NULL curr_dr_freq");
+		return -EINVAL;
+	}
+
+	divider	= (params->max_dr_freq / params->curr_dr_freq) - 1;
+
+	if (params->next_bank)
+		mcp_clkctrl_off = CDNS_MCP_CLK_CTRL1;
+	else
+		mcp_clkctrl_off = CDNS_MCP_CLK_CTRL0;
+
+	mcp_clkctrl = cdns_readl(cdns, mcp_clkctrl_off);
+	mcp_clkctrl |= divider;
+	cdns_writel(cdns, mcp_clkctrl_off, mcp_clkctrl);
+
+	return 0;
+}
+EXPORT_SYMBOL(cdns_bus_conf);
+
+static int cdns_port_params(struct sdw_bus *bus,
+		struct sdw_port_params *p_params, unsigned int bank)
+{
+	struct sdw_cdns *cdns = bus_to_cdns(bus);
+	int dpn_config = 0, dpn_config_off;
+
+	if (bank)
+		dpn_config_off = CDNS_DPN_B1_CONFIG(p_params->num);
+	else
+		dpn_config_off = CDNS_DPN_B0_CONFIG(p_params->num);
+
+	dpn_config = cdns_readl(cdns, dpn_config_off);
+
+	dpn_config |= ((p_params->bps - 1) <<
+				SDW_REG_SHIFT(CDNS_DPN_CONFIG_WL));
+	dpn_config |= (p_params->flow_mode <<
+				SDW_REG_SHIFT(CDNS_DPN_CONFIG_PORT_FLOW));
+	dpn_config |= (p_params->data_mode <<
+				SDW_REG_SHIFT(CDNS_DPN_CONFIG_PORT_DAT));
+
+	cdns_writel(cdns, dpn_config_off, dpn_config);
+
+	return 0;
+}
+
+static int cdns_transport_params(struct sdw_bus *bus,
+			struct sdw_transport_params *t_params,
+			enum sdw_reg_bank bank)
+{
+	struct sdw_cdns *cdns = bus_to_cdns(bus);
+	int dpn_offsetctrl = 0, dpn_offsetctrl_off;
+	int dpn_config = 0, dpn_config_off;
+	int dpn_hctrl = 0, dpn_hctrl_off;
+	int num = t_params->port_num;
+	int dpn_samplectrl_off;
+
+	/*
+	 * Note: Only full data port is supported on the Master side for
+	 * both PCM and PDM ports.
+	 */
+
+	if (bank) {
+		dpn_config_off = CDNS_DPN_B1_CONFIG(num);
+		dpn_samplectrl_off = CDNS_DPN_B1_SAMPLE_CTRL(num);
+		dpn_hctrl_off = CDNS_DPN_B1_HCTRL(num);
+		dpn_offsetctrl_off = CDNS_DPN_B1_OFFSET_CTRL(num);
+	} else {
+		dpn_config_off = CDNS_DPN_B0_CONFIG(num);
+		dpn_samplectrl_off = CDNS_DPN_B0_SAMPLE_CTRL(num);
+		dpn_hctrl_off = CDNS_DPN_B0_HCTRL(num);
+		dpn_offsetctrl_off = CDNS_DPN_B0_OFFSET_CTRL(num);
+	}
+
+	dpn_config = cdns_readl(cdns, dpn_config_off);
+
+	dpn_config |= (t_params->blk_grp_ctrl <<
+				SDW_REG_SHIFT(CDNS_DPN_CONFIG_BGC));
+	dpn_config |= (t_params->blk_pkg_mode <<
+				SDW_REG_SHIFT(CDNS_DPN_CONFIG_BPM));
+	cdns_writel(cdns, dpn_config_off, dpn_config);
+
+	dpn_offsetctrl |= (t_params->offset1 <<
+				SDW_REG_SHIFT(CDNS_DPN_OFFSET_CTRL_1));
+	dpn_offsetctrl |= (t_params->offset2 <<
+				SDW_REG_SHIFT(CDNS_DPN_OFFSET_CTRL_2));
+	cdns_writel(cdns, dpn_offsetctrl_off,  dpn_offsetctrl);
+
+	dpn_hctrl |= (t_params->hstart <<
+				SDW_REG_SHIFT(CDNS_DPN_HCTRL_HSTART));
+	dpn_hctrl |= (t_params->hstop << SDW_REG_SHIFT(CDNS_DPN_HCTRL_HSTOP));
+	dpn_hctrl |= (t_params->lane_ctrl <<
+				SDW_REG_SHIFT(CDNS_DPN_HCTRL_LCTRL));
+
+	cdns_writel(cdns, dpn_hctrl_off, dpn_hctrl);
+	cdns_writel(cdns, dpn_samplectrl_off, (t_params->sample_interval - 1));
+
+	return 0;
+}
+
+static int cdns_port_enable(struct sdw_bus *bus,
+		struct sdw_enable_ch *enable_ch, unsigned int bank)
+{
+	struct sdw_cdns *cdns = bus_to_cdns(bus);
+	int dpn_chnen_off, ch_mask;
+
+	if (bank)
+		dpn_chnen_off = CDNS_DPN_B1_CH_EN(enable_ch->port_num);
+	else
+		dpn_chnen_off = CDNS_DPN_B0_CH_EN(enable_ch->port_num);
+
+	ch_mask = enable_ch->ch_mask * enable_ch->enable;
+	cdns_writel(cdns, dpn_chnen_off, ch_mask);
+
+	return 0;
+}
+
+static const struct sdw_master_port_ops cdns_port_ops = {
+	.dpn_set_port_params = cdns_port_params,
+	.dpn_set_port_transport_params = cdns_transport_params,
+	.dpn_port_enable_ch = cdns_port_enable,
 };
-EXPORT_SYMBOL(sdw_cdns_master_ops);
 
 /**
  * sdw_cdns_probe() - Cadence probe routine
@@ -742,10 +981,204 @@ EXPORT_SYMBOL(sdw_cdns_master_ops);
 int sdw_cdns_probe(struct sdw_cdns *cdns)
 {
 	init_completion(&cdns->tx_complete);
+	cdns->bus.port_ops = &cdns_port_ops;
 
 	return 0;
 }
 EXPORT_SYMBOL(sdw_cdns_probe);
 
+int cdns_set_sdw_stream(struct snd_soc_dai *dai,
+		void *stream, bool pcm, int direction)
+{
+	struct sdw_cdns *cdns = snd_soc_dai_get_drvdata(dai);
+	struct sdw_cdns_dma_data *dma;
+
+	dma = kzalloc(sizeof(*dma), GFP_KERNEL);
+	if (!dma)
+		return -ENOMEM;
+
+	if (pcm)
+		dma->stream_type = SDW_STREAM_PCM;
+	else
+		dma->stream_type = SDW_STREAM_PDM;
+
+	dma->bus = &cdns->bus;
+	dma->link_id = cdns->instance;
+
+	dma->stream = stream;
+
+	if (direction == SNDRV_PCM_STREAM_PLAYBACK)
+		dai->playback_dma_data = dma;
+	else
+		dai->capture_dma_data = dma;
+
+	return 0;
+}
+EXPORT_SYMBOL(cdns_set_sdw_stream);
+
+/**
+ * cdns_find_pdi() - Find a free PDI
+ *
+ * @cdns: Cadence instance
+ * @num: Number of PDIs
+ * @pdi: PDI instances
+ *
+ * Find and return a free PDI for a given PDI array
+ */
+static struct sdw_cdns_pdi *cdns_find_pdi(struct sdw_cdns *cdns,
+		unsigned int num, struct sdw_cdns_pdi *pdi)
+{
+	int i;
+
+	for (i = 0; i < num; i++) {
+		if (pdi[i].assigned == true)
+			continue;
+		pdi[i].assigned = true;
+		return &pdi[i];
+	}
+
+	return NULL;
+}
+
+/**
+ * sdw_cdns_config_stream: Configure a stream
+ *
+ * @cdns: Cadence instance
+ * @port: Cadence data port
+ * @ch: Channel count
+ * @dir: Data direction
+ * @pdi: PDI to be used
+ */
+void sdw_cdns_config_stream(struct sdw_cdns *cdns,
+				struct sdw_cdns_port *port,
+				u32 ch, u32 dir, struct sdw_cdns_pdi *pdi)
+{
+	u32 offset, val = 0;
+
+	if (dir == SDW_DATA_DIR_RX)
+		val = CDNS_PORTCTRL_DIRN;
+
+	offset = CDNS_PORTCTRL + port->num * CDNS_PORT_OFFSET;
+	cdns_updatel(cdns, offset, CDNS_PORTCTRL_DIRN, val);
+
+	val = port->num;
+	val |= ((1 << ch) - 1) << SDW_REG_SHIFT(CDNS_PDI_CONFIG_CHANNEL);
+	cdns_writel(cdns, CDNS_PDI_CONFIG(pdi->num), val);
+}
+EXPORT_SYMBOL(sdw_cdns_config_stream);
+
+/**
+ * cdns_get_num_pdi() - Get number of PDIs required
+ *
+ * @cdns: Cadence instance
+ * @pdi: PDI to be used
+ * @num: Number of PDIs
+ * @ch_count: Channel count
+ */
+static int cdns_get_num_pdi(struct sdw_cdns *cdns,
+		struct sdw_cdns_pdi *pdi,
+		unsigned int num, u32 ch_count)
+{
+	int i, pdis = 0;
+
+	for (i = 0; i < num; i++) {
+		if (pdi[i].assigned == true)
+			continue;
+
+		if (pdi[i].ch_count < ch_count)
+			ch_count -= pdi[i].ch_count;
+		else
+			ch_count = 0;
+
+		pdis++;
+
+		if (!ch_count)
+			break;
+	}
+
+	if (ch_count)
+		return 0;
+
+	return pdis;
+}
+
+/**
+ * sdw_cdns_get_stream() - Get stream information
+ *
+ * @cdns: Cadence instance
+ * @stream: Stream to be allocated
+ * @ch: Channel count
+ * @dir: Data direction
+ */
+int sdw_cdns_get_stream(struct sdw_cdns *cdns,
+			struct sdw_cdns_streams *stream,
+			u32 ch, u32 dir)
+{
+	int pdis = 0;
+
+	if (dir == SDW_DATA_DIR_RX)
+		pdis = cdns_get_num_pdi(cdns, stream->in, stream->num_in, ch);
+	else
+		pdis = cdns_get_num_pdi(cdns, stream->out, stream->num_out, ch);
+
+	/* check if we found PDI, else find in bi-directional */
+	if (!pdis)
+		pdis = cdns_get_num_pdi(cdns, stream->bd, stream->num_bd, ch);
+
+	return pdis;
+}
+EXPORT_SYMBOL(sdw_cdns_get_stream);
+
+/**
+ * sdw_cdns_alloc_stream() - Allocate a stream
+ *
+ * @cdns: Cadence instance
+ * @stream: Stream to be allocated
+ * @port: Cadence data port
+ * @ch: Channel count
+ * @dir: Data direction
+ */
+int sdw_cdns_alloc_stream(struct sdw_cdns *cdns,
+			struct sdw_cdns_streams *stream,
+			struct sdw_cdns_port *port, u32 ch, u32 dir)
+{
+	struct sdw_cdns_pdi *pdi = NULL;
+
+	if (dir == SDW_DATA_DIR_RX)
+		pdi = cdns_find_pdi(cdns, stream->num_in, stream->in);
+	else
+		pdi = cdns_find_pdi(cdns, stream->num_out, stream->out);
+
+	/* check if we found a PDI, else find in bi-directional */
+	if (!pdi)
+		pdi = cdns_find_pdi(cdns, stream->num_bd, stream->bd);
+
+	if (!pdi)
+		return -EIO;
+
+	port->pdi = pdi;
+	pdi->l_ch_num = 0;
+	pdi->h_ch_num = ch - 1;
+	pdi->dir = dir;
+	pdi->ch_count = ch;
+
+	return 0;
+}
+EXPORT_SYMBOL(sdw_cdns_alloc_stream);
+
+void sdw_cdns_shutdown(struct snd_pcm_substream *substream,
+					struct snd_soc_dai *dai)
+{
+	struct sdw_cdns_dma_data *dma;
+
+	dma = snd_soc_dai_get_dma_data(dai, substream);
+	if (!dma)
+		return;
+
+	snd_soc_dai_set_dma_data(dai, substream, NULL);
+	kfree(dma);
+}
+EXPORT_SYMBOL(sdw_cdns_shutdown);
+
 MODULE_LICENSE("Dual BSD/GPL");
 MODULE_DESCRIPTION("Cadence Soundwire Library");

drivers/soundwire/cadence_master.h

@@ -1,9 +1,116 @@
 // SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
 // Copyright(c) 2015-17 Intel Corporation.
+#include <sound/soc.h>
 
 #ifndef __SDW_CADENCE_H
 #define __SDW_CADENCE_H
 
+/**
+ * struct sdw_cdns_pdi: PDI (Physical Data Interface) instance
+ *
+ * @assigned: pdi assigned
+ * @num: pdi number
+ * @intel_alh_id: link identifier
+ * @l_ch_num: low channel for PDI
+ * @h_ch_num: high channel for PDI
+ * @ch_count: total channel count for PDI
+ * @dir: data direction
+ * @type: stream type, PDM or PCM
+ */
+struct sdw_cdns_pdi {
+	bool assigned;
+	int num;
+	int intel_alh_id;
+	int l_ch_num;
+	int h_ch_num;
+	int ch_count;
+	enum sdw_data_direction dir;
+	enum sdw_stream_type type;
+};
+
+/**
+ * struct sdw_cdns_port: Cadence port structure
+ *
+ * @num: port number
+ * @assigned: port assigned
+ * @ch: channel count
+ * @direction: data port direction
+ * @pdi: pdi for this port
+ */
+struct sdw_cdns_port {
+	unsigned int num;
+	bool assigned;
+	unsigned int ch;
+	enum sdw_data_direction direction;
+	struct sdw_cdns_pdi *pdi;
+};
+
+/**
+ * struct sdw_cdns_streams: Cadence stream data structure
+ *
+ * @num_bd: number of bidirectional streams
+ * @num_in: number of input streams
+ * @num_out: number of output streams
+ * @num_ch_bd: number of bidirectional stream channels
+ * @num_ch_bd: number of input stream channels
+ * @num_ch_bd: number of output stream channels
+ * @num_pdi: total number of PDIs
+ * @bd: bidirectional streams
+ * @in: input streams
+ * @out: output streams
+ */
+struct sdw_cdns_streams {
+	unsigned int num_bd;
+	unsigned int num_in;
+	unsigned int num_out;
+	unsigned int num_ch_bd;
+	unsigned int num_ch_in;
+	unsigned int num_ch_out;
+	unsigned int num_pdi;
+	struct sdw_cdns_pdi *bd;
+	struct sdw_cdns_pdi *in;
+	struct sdw_cdns_pdi *out;
+};
+
+/**
+ * struct sdw_cdns_stream_config: stream configuration
+ *
+ * @pcm_bd: number of bidirectional PCM streams supported
+ * @pcm_in: number of input PCM streams supported
+ * @pcm_out: number of output PCM streams supported
+ * @pdm_bd: number of bidirectional PDM streams supported
+ * @pdm_in: number of input PDM streams supported
+ * @pdm_out: number of output PDM streams supported
+ */
+struct sdw_cdns_stream_config {
+	unsigned int pcm_bd;
+	unsigned int pcm_in;
+	unsigned int pcm_out;
+	unsigned int pdm_bd;
+	unsigned int pdm_in;
+	unsigned int pdm_out;
+};
+
+/**
+ * struct sdw_cdns_dma_data: Cadence DMA data
+ *
+ * @name: SoundWire stream name
+ * @nr_ports: Number of ports
+ * @port: Ports
+ * @bus: Bus handle
+ * @stream_type: Stream type
+ * @link_id: Master link id
+ */
+struct sdw_cdns_dma_data {
+	char *name;
+	struct sdw_stream_runtime *stream;
+	int nr_ports;
+	struct sdw_cdns_port **port;
+	struct sdw_bus *bus;
+	enum sdw_stream_type stream_type;
+	int link_id;
+};
+
 /**
  * struct sdw_cdns - Cadence driver context
  * @dev: Linux device
@@ -12,6 +119,10 @@
  * @response_buf: SoundWire response buffer
  * @tx_complete: Tx completion
  * @defer: Defer pointer
+ * @ports: Data ports
+ * @num_ports: Total number of data ports
+ * @pcm: PCM streams
+ * @pdm: PDM streams
  * @registers: Cadence registers
  * @link_up: Link status
  * @msg_count: Messages sent on bus
@@ -25,6 +136,12 @@ struct sdw_cdns {
 	struct completion tx_complete;
 	struct sdw_defer *defer;
 
+	struct sdw_cdns_port *ports;
+	int num_ports;
+
+	struct sdw_cdns_streams pcm;
+	struct sdw_cdns_streams pdm;
+
 	void __iomem *registers;
 
 	bool link_up;
@@ -42,7 +159,41 @@ irqreturn_t sdw_cdns_irq(int irq, void *dev_id);
 irqreturn_t sdw_cdns_thread(int irq, void *dev_id);
 
 int sdw_cdns_init(struct sdw_cdns *cdns);
+int sdw_cdns_pdi_init(struct sdw_cdns *cdns,
+			struct sdw_cdns_stream_config config);
 int sdw_cdns_enable_interrupt(struct sdw_cdns *cdns);
 
+int sdw_cdns_get_stream(struct sdw_cdns *cdns,
+			struct sdw_cdns_streams *stream,
+			u32 ch, u32 dir);
+int sdw_cdns_alloc_stream(struct sdw_cdns *cdns,
+			struct sdw_cdns_streams *stream,
+			struct sdw_cdns_port *port, u32 ch, u32 dir);
+void sdw_cdns_config_stream(struct sdw_cdns *cdns, struct sdw_cdns_port *port,
+			u32 ch, u32 dir, struct sdw_cdns_pdi *pdi);
+
+void sdw_cdns_shutdown(struct snd_pcm_substream *substream,
+				struct snd_soc_dai *dai);
+int sdw_cdns_pcm_set_stream(struct snd_soc_dai *dai,
+				void *stream, int direction);
+int sdw_cdns_pdm_set_stream(struct snd_soc_dai *dai,
+				void *stream, int direction);
+
+enum sdw_command_response
+cdns_reset_page_addr(struct sdw_bus *bus, unsigned int dev_num);
+
+enum sdw_command_response
+cdns_xfer_msg(struct sdw_bus *bus, struct sdw_msg *msg);
+
+enum sdw_command_response
+cdns_xfer_msg_defer(struct sdw_bus *bus,
+		struct sdw_msg *msg, struct sdw_defer *defer);
+
+enum sdw_command_response
+cdns_reset_page_addr(struct sdw_bus *bus, unsigned int dev_num);
+
+int cdns_bus_conf(struct sdw_bus *bus, struct sdw_bus_params *params);
 
+int cdns_set_sdw_stream(struct snd_soc_dai *dai,
+		void *stream, bool pcm, int direction);
 #endif /* __SDW_CADENCE_H */

drivers/soundwire/intel.c

@@ -9,6 +9,8 @@
 #include <linux/delay.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
 #include <linux/soundwire/sdw_registers.h>
 #include <linux/soundwire/sdw.h>
 #include <linux/soundwire/sdw_intel.h>
@@ -85,6 +87,12 @@
 #define SDW_ALH_STRMZCFG_DMAT		GENMASK(7, 0)
 #define SDW_ALH_STRMZCFG_CHN		GENMASK(19, 16)
 
+enum intel_pdi_type {
+	INTEL_PDI_IN = 0,
+	INTEL_PDI_OUT = 1,
+	INTEL_PDI_BD = 2,
+};
+
 struct sdw_intel {
 	struct sdw_cdns cdns;
 	int instance;
@@ -234,6 +242,490 @@ static int intel_shim_init(struct sdw_intel *sdw)
 	return ret;
 }
 
+/*
+ * PDI routines
+ */
+static void intel_pdi_init(struct sdw_intel *sdw,
+			struct sdw_cdns_stream_config *config)
+{
+	void __iomem *shim = sdw->res->shim;
+	unsigned int link_id = sdw->instance;
+	int pcm_cap, pdm_cap;
+
+	/* PCM Stream Capability */
+	pcm_cap = intel_readw(shim, SDW_SHIM_PCMSCAP(link_id));
+
+	config->pcm_bd = (pcm_cap & SDW_SHIM_PCMSCAP_BSS) >>
+					SDW_REG_SHIFT(SDW_SHIM_PCMSCAP_BSS);
+	config->pcm_in = (pcm_cap & SDW_SHIM_PCMSCAP_ISS) >>
+					SDW_REG_SHIFT(SDW_SHIM_PCMSCAP_ISS);
+	config->pcm_out = (pcm_cap & SDW_SHIM_PCMSCAP_OSS) >>
+					SDW_REG_SHIFT(SDW_SHIM_PCMSCAP_OSS);
+
+	/* PDM Stream Capability */
+	pdm_cap = intel_readw(shim, SDW_SHIM_PDMSCAP(link_id));
+
+	config->pdm_bd = (pdm_cap & SDW_SHIM_PDMSCAP_BSS) >>
+					SDW_REG_SHIFT(SDW_SHIM_PDMSCAP_BSS);
+	config->pdm_in = (pdm_cap & SDW_SHIM_PDMSCAP_ISS) >>
+					SDW_REG_SHIFT(SDW_SHIM_PDMSCAP_ISS);
+	config->pdm_out = (pdm_cap & SDW_SHIM_PDMSCAP_OSS) >>
+					SDW_REG_SHIFT(SDW_SHIM_PDMSCAP_OSS);
+}
+
+static int
+intel_pdi_get_ch_cap(struct sdw_intel *sdw, unsigned int pdi_num, bool pcm)
+{
+	void __iomem *shim = sdw->res->shim;
+	unsigned int link_id = sdw->instance;
+	int count;
+
+	if (pcm) {
+		count = intel_readw(shim, SDW_SHIM_PCMSYCHC(link_id, pdi_num));
+	} else {
+		count = intel_readw(shim, SDW_SHIM_PDMSCAP(link_id));
+		count = ((count & SDW_SHIM_PDMSCAP_CPSS) >>
+					SDW_REG_SHIFT(SDW_SHIM_PDMSCAP_CPSS));
+	}
+
+	/* zero based values for channel count in register */
+	count++;
+
+	return count;
+}
+
+static int intel_pdi_get_ch_update(struct sdw_intel *sdw,
+				struct sdw_cdns_pdi *pdi,
+				unsigned int num_pdi,
+				unsigned int *num_ch, bool pcm)
+{
+	int i, ch_count = 0;
+
+	for (i = 0; i < num_pdi; i++) {
+		pdi->ch_count = intel_pdi_get_ch_cap(sdw, pdi->num, pcm);
+		ch_count += pdi->ch_count;
+		pdi++;
+	}
+
+	*num_ch = ch_count;
+	return 0;
+}
+
+static int intel_pdi_stream_ch_update(struct sdw_intel *sdw,
+				struct sdw_cdns_streams *stream, bool pcm)
+{
+	intel_pdi_get_ch_update(sdw, stream->bd, stream->num_bd,
+			&stream->num_ch_bd, pcm);
+
+	intel_pdi_get_ch_update(sdw, stream->in, stream->num_in,
+			&stream->num_ch_in, pcm);
+
+	intel_pdi_get_ch_update(sdw, stream->out, stream->num_out,
+			&stream->num_ch_out, pcm);
+
+	return 0;
+}
+
+static int intel_pdi_ch_update(struct sdw_intel *sdw)
+{
+	/* First update PCM streams followed by PDM streams */
+	intel_pdi_stream_ch_update(sdw, &sdw->cdns.pcm, true);
+	intel_pdi_stream_ch_update(sdw, &sdw->cdns.pdm, false);
+
+	return 0;
+}
+
+static void
+intel_pdi_shim_configure(struct sdw_intel *sdw, struct sdw_cdns_pdi *pdi)
+{
+	void __iomem *shim = sdw->res->shim;
+	unsigned int link_id = sdw->instance;
+	int pdi_conf = 0;
+
+	pdi->intel_alh_id = (link_id * 16) + pdi->num + 5;
+
+	/*
+	 * Program stream parameters to stream SHIM register
+	 * This is applicable for PCM stream only.
+	 */
+	if (pdi->type != SDW_STREAM_PCM)
+		return;
+
+	if (pdi->dir == SDW_DATA_DIR_RX)
+		pdi_conf |= SDW_SHIM_PCMSYCM_DIR;
+	else
+		pdi_conf &= ~(SDW_SHIM_PCMSYCM_DIR);
+
+	pdi_conf |= (pdi->intel_alh_id <<
+			SDW_REG_SHIFT(SDW_SHIM_PCMSYCM_STREAM));
+	pdi_conf |= (pdi->l_ch_num << SDW_REG_SHIFT(SDW_SHIM_PCMSYCM_LCHN));
+	pdi_conf |= (pdi->h_ch_num << SDW_REG_SHIFT(SDW_SHIM_PCMSYCM_HCHN));
+
+	intel_writew(shim, SDW_SHIM_PCMSYCHM(link_id, pdi->num), pdi_conf);
+}
+
+static void
+intel_pdi_alh_configure(struct sdw_intel *sdw, struct sdw_cdns_pdi *pdi)
+{
+	void __iomem *alh = sdw->res->alh;
+	unsigned int link_id = sdw->instance;
+	unsigned int conf;
+
+	pdi->intel_alh_id = (link_id * 16) + pdi->num + 5;
+
+	/* Program Stream config ALH register */
+	conf = intel_readl(alh, SDW_ALH_STRMZCFG(pdi->intel_alh_id));
+
+	conf |= (SDW_ALH_STRMZCFG_DMAT_VAL <<
+			SDW_REG_SHIFT(SDW_ALH_STRMZCFG_DMAT));
+
+	conf |= ((pdi->ch_count - 1) <<
+			SDW_REG_SHIFT(SDW_ALH_STRMZCFG_CHN));
+
+	intel_writel(alh, SDW_ALH_STRMZCFG(pdi->intel_alh_id), conf);
+}
+
+static int intel_config_stream(struct sdw_intel *sdw,
+			struct snd_pcm_substream *substream,
+			struct snd_soc_dai *dai,
+			struct snd_pcm_hw_params *hw_params, int link_id)
+{
+	if (sdw->res->ops && sdw->res->ops->config_stream)
+		return sdw->res->ops->config_stream(sdw->res->arg,
+				substream, dai, hw_params, link_id);
+
+	return -EIO;
+}
+
+/*
+ * DAI routines
+ */
+
+static struct sdw_cdns_port *intel_alloc_port(struct sdw_intel *sdw,
+				u32 ch, u32 dir, bool pcm)
+{
+	struct sdw_cdns *cdns = &sdw->cdns;
+	struct sdw_cdns_port *port = NULL;
+	int i, ret = 0;
+
+	for (i = 0; i < cdns->num_ports; i++) {
+		if (cdns->ports[i].assigned == true)
+			continue;
+
+		port = &cdns->ports[i];
+		port->assigned = true;
+		port->direction = dir;
+		port->ch = ch;
+		break;
+	}
+
+	if (!port) {
+		dev_err(cdns->dev, "Unable to find a free port\n");
+		return NULL;
+	}
+
+	if (pcm) {
+		ret = sdw_cdns_alloc_stream(cdns, &cdns->pcm, port, ch, dir);
+		if (ret)
+			goto out;
+
+		intel_pdi_shim_configure(sdw, port->pdi);
+		sdw_cdns_config_stream(cdns, port, ch, dir, port->pdi);
+
+		intel_pdi_alh_configure(sdw, port->pdi);
+
+	} else {
+		ret = sdw_cdns_alloc_stream(cdns, &cdns->pdm, port, ch, dir);
+	}
+
+out:
+	if (ret) {
+		port->assigned = false;
+		port = NULL;
+	}
+
+	return port;
+}
+
+static void intel_port_cleanup(struct sdw_cdns_dma_data *dma)
+{
+	int i;
+
+	for (i = 0; i < dma->nr_ports; i++) {
+		if (dma->port[i]) {
+			dma->port[i]->pdi->assigned = false;
+			dma->port[i]->pdi = NULL;
+			dma->port[i]->assigned = false;
+			dma->port[i] = NULL;
+		}
+	}
+}
+
+static int intel_hw_params(struct snd_pcm_substream *substream,
+				struct snd_pcm_hw_params *params,
+				struct snd_soc_dai *dai)
+{
+	struct sdw_cdns *cdns = snd_soc_dai_get_drvdata(dai);
+	struct sdw_intel *sdw = cdns_to_intel(cdns);
+	struct sdw_cdns_dma_data *dma;
+	struct sdw_stream_config sconfig;
+	struct sdw_port_config *pconfig;
+	int ret, i, ch, dir;
+	bool pcm = true;
+
+	dma = snd_soc_dai_get_dma_data(dai, substream);
+	if (!dma)
+		return -EIO;
+
+	ch = params_channels(params);
+	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
+		dir = SDW_DATA_DIR_RX;
+	else
+		dir = SDW_DATA_DIR_TX;
+
+	if (dma->stream_type == SDW_STREAM_PDM) {
+		/* TODO: Check whether PDM decimator is already in use */
+		dma->nr_ports = sdw_cdns_get_stream(cdns, &cdns->pdm, ch, dir);
+		pcm = false;
+	} else {
+		dma->nr_ports = sdw_cdns_get_stream(cdns, &cdns->pcm, ch, dir);
+	}
+
+	if (!dma->nr_ports) {
+		dev_err(dai->dev, "ports/resources not available");
+		return -EINVAL;
+	}
+
+	dma->port = kcalloc(dma->nr_ports, sizeof(*dma->port), GFP_KERNEL);
+	if (!dma->port)
+		return -ENOMEM;
+
+	for (i = 0; i < dma->nr_ports; i++) {
+		dma->port[i] = intel_alloc_port(sdw, ch, dir, pcm);
+		if (!dma->port[i]) {
+			ret = -EINVAL;
+			goto port_error;
+		}
+	}
+
+	/* Inform DSP about PDI stream number */
+	for (i = 0; i < dma->nr_ports; i++) {
+		ret = intel_config_stream(sdw, substream, dai, params,
+				dma->port[i]->pdi->intel_alh_id);
+		if (ret)
+			goto port_error;
+	}
+
+	sconfig.direction = dir;
+	sconfig.ch_count = ch;
+	sconfig.frame_rate = params_rate(params);
+	sconfig.type = dma->stream_type;
+
+	if (dma->stream_type == SDW_STREAM_PDM) {
+		sconfig.frame_rate *= 50;
+		sconfig.bps = 1;
+	} else {
+		sconfig.bps = snd_pcm_format_width(params_format(params));
+	}
+
+	/* Port configuration */
+	pconfig = kcalloc(dma->nr_ports, sizeof(*pconfig), GFP_KERNEL);
+	if (!pconfig) {
+		ret =  -ENOMEM;
+		goto port_error;
+	}
+
+	for (i = 0; i < dma->nr_ports; i++) {
+		pconfig[i].num = dma->port[i]->num;
+		pconfig[i].ch_mask = (1 << ch) - 1;
+	}
+
+	ret = sdw_stream_add_master(&cdns->bus, &sconfig,
+				pconfig, dma->nr_ports, dma->stream);
+	if (ret) {
+		dev_err(cdns->dev, "add master to stream failed:%d", ret);
+		goto stream_error;
+	}
+
+	kfree(pconfig);
+	return ret;
+
+stream_error:
+	kfree(pconfig);
+port_error:
+	intel_port_cleanup(dma);
+	kfree(dma->port);
+	return ret;
+}
+
+static int
+intel_hw_free(struct snd_pcm_substream *substream, struct snd_soc_dai *dai)
+{
+	struct sdw_cdns *cdns = snd_soc_dai_get_drvdata(dai);
+	struct sdw_cdns_dma_data *dma;
+	int ret;
+
+	dma = snd_soc_dai_get_dma_data(dai, substream);
+	if (!dma)
+		return -EIO;
+
+	ret = sdw_stream_remove_master(&cdns->bus, dma->stream);
+	if (ret < 0)
+		dev_err(dai->dev, "remove master from stream %s failed: %d",
+							dma->stream->name, ret);
+
+	intel_port_cleanup(dma);
+	kfree(dma->port);
+	return ret;
+}
+
+static int intel_pcm_set_sdw_stream(struct snd_soc_dai *dai,
+					void *stream, int direction)
+{
+	return cdns_set_sdw_stream(dai, stream, true, direction);
+}
+
+static int intel_pdm_set_sdw_stream(struct snd_soc_dai *dai,
+					void *stream, int direction)
+{
+	return cdns_set_sdw_stream(dai, stream, false, direction);
+}
+
+static struct snd_soc_dai_ops intel_pcm_dai_ops = {
+	.hw_params = intel_hw_params,
+	.hw_free = intel_hw_free,
+	.shutdown = sdw_cdns_shutdown,
+	.set_sdw_stream = intel_pcm_set_sdw_stream,
+};
+
+static struct snd_soc_dai_ops intel_pdm_dai_ops = {
+	.hw_params = intel_hw_params,
+	.hw_free = intel_hw_free,
+	.shutdown = sdw_cdns_shutdown,
+	.set_sdw_stream = intel_pdm_set_sdw_stream,
+};
+
+static const struct snd_soc_component_driver dai_component = {
+	.name           = "soundwire",
+};
+
+static int intel_create_dai(struct sdw_cdns *cdns,
+			struct snd_soc_dai_driver *dais,
+			enum intel_pdi_type type,
+			u32 num, u32 off, u32 max_ch, bool pcm)
+{
+	int i;
+
+	if (num == 0)
+		return 0;
+
+	 /* TODO: Read supported rates/formats from hardware */
+	for (i = off; i < (off + num); i++) {
+		dais[i].name = kasprintf(GFP_KERNEL, "SDW%d Pin%d",
+					cdns->instance, i);
+		if (!dais[i].name)
+			return -ENOMEM;
+
+		if (type == INTEL_PDI_BD || type == INTEL_PDI_OUT) {
+			dais[i].playback.stream_name = kasprintf(GFP_KERNEL,
+							"SDW%d Tx%d",
+							cdns->instance, i);
+			if (!dais[i].playback.stream_name) {
+				kfree(dais[i].name);
+				return -ENOMEM;
+			}
+
+			dais[i].playback.channels_min = 1;
+			dais[i].playback.channels_max = max_ch;
+			dais[i].playback.rates = SNDRV_PCM_RATE_48000;
+			dais[i].playback.formats = SNDRV_PCM_FMTBIT_S16_LE;
+		}
+
+		if (type == INTEL_PDI_BD || type == INTEL_PDI_IN) {
+			dais[i].capture.stream_name = kasprintf(GFP_KERNEL,
+							"SDW%d Rx%d",
+							cdns->instance, i);
+			if (!dais[i].capture.stream_name) {
+				kfree(dais[i].name);
+				kfree(dais[i].playback.stream_name);
+				return -ENOMEM;
+			}
+
+			dais[i].playback.channels_min = 1;
+			dais[i].playback.channels_max = max_ch;
+			dais[i].capture.rates = SNDRV_PCM_RATE_48000;
+			dais[i].capture.formats = SNDRV_PCM_FMTBIT_S16_LE;
+		}
+
+		dais[i].id = SDW_DAI_ID_RANGE_START + i;
+
+		if (pcm)
+			dais[i].ops = &intel_pcm_dai_ops;
+		else
+			dais[i].ops = &intel_pdm_dai_ops;
+	}
+
+	return 0;
+}
+
+static int intel_register_dai(struct sdw_intel *sdw)
+{
+	struct sdw_cdns *cdns = &sdw->cdns;
+	struct sdw_cdns_streams *stream;
+	struct snd_soc_dai_driver *dais;
+	int num_dai, ret, off = 0;
+
+	/* DAIs are created based on total number of PDIs supported */
+	num_dai = cdns->pcm.num_pdi + cdns->pdm.num_pdi;
+
+	dais = devm_kcalloc(cdns->dev, num_dai, sizeof(*dais), GFP_KERNEL);
+	if (!dais)
+		return -ENOMEM;
+
+	/* Create PCM DAIs */
+	stream = &cdns->pcm;
+
+	ret = intel_create_dai(cdns, dais, INTEL_PDI_IN,
+			stream->num_in, off, stream->num_ch_in, true);
+	if (ret)
+		return ret;
+
+	off += cdns->pcm.num_in;
+	ret = intel_create_dai(cdns, dais, INTEL_PDI_OUT,
+			cdns->pcm.num_out, off, stream->num_ch_out, true);
+	if (ret)
+		return ret;
+
+	off += cdns->pcm.num_out;
+	ret = intel_create_dai(cdns, dais, INTEL_PDI_BD,
+			cdns->pcm.num_bd, off, stream->num_ch_bd, true);
+	if (ret)
+		return ret;
+
+	/* Create PDM DAIs */
+	stream = &cdns->pdm;
+	off += cdns->pcm.num_bd;
+	ret = intel_create_dai(cdns, dais, INTEL_PDI_IN,
+			cdns->pdm.num_in, off, stream->num_ch_in, false);
+	if (ret)
+		return ret;
+
+	off += cdns->pdm.num_in;
+	ret = intel_create_dai(cdns, dais, INTEL_PDI_OUT,
+			cdns->pdm.num_out, off, stream->num_ch_out, false);
+	if (ret)
+		return ret;
+
+	off += cdns->pdm.num_bd;
+	ret = intel_create_dai(cdns, dais, INTEL_PDI_BD,
+			cdns->pdm.num_bd, off, stream->num_ch_bd, false);
+	if (ret)
+		return ret;
+
+	return snd_soc_register_component(cdns->dev, &dai_component,
+				dais, num_dai);
+}
+
 static int intel_prop_read(struct sdw_bus *bus)
 {
 	/* Initialize with default handler to read all DisCo properties */
@@ -252,11 +744,20 @@ static int intel_prop_read(struct sdw_bus *bus)
 	return 0;
 }
 
+static struct sdw_master_ops sdw_intel_ops = {
+	.read_prop = sdw_master_read_prop,
+	.xfer_msg = cdns_xfer_msg,
+	.xfer_msg_defer = cdns_xfer_msg_defer,
+	.reset_page_addr = cdns_reset_page_addr,
+	.set_bus_conf = cdns_bus_conf,
+};
+
 /*
  * probe and init
  */
 static int intel_probe(struct platform_device *pdev)
 {
+	struct sdw_cdns_stream_config config;
 	struct sdw_intel *sdw;
 	int ret;
 
@@ -276,8 +777,11 @@ static int intel_probe(struct platform_device *pdev)
 	sdw_cdns_probe(&sdw->cdns);
 
 	/* Set property read ops */
-	sdw_cdns_master_ops.read_prop = intel_prop_read;
-	sdw->cdns.bus.ops = &sdw_cdns_master_ops;
+	sdw_intel_ops.read_prop = intel_prop_read;
+	sdw->cdns.bus.ops = &sdw_intel_ops;
+
+	sdw_intel_ops.read_prop = intel_prop_read;
+	sdw->cdns.bus.ops = &sdw_intel_ops;
 
 	platform_set_drvdata(pdev, sdw);
 
@@ -296,9 +800,15 @@ static int intel_probe(struct platform_device *pdev)
 		goto err_init;
 
 	ret = sdw_cdns_enable_interrupt(&sdw->cdns);
+
+	/* Read the PDI config and initialize cadence PDI */
+	intel_pdi_init(sdw, &config);
+	ret = sdw_cdns_pdi_init(&sdw->cdns, config);
 	if (ret)
 		goto err_init;
 
+	intel_pdi_ch_update(sdw);
+
 	/* Acquire IRQ */
 	ret = request_threaded_irq(sdw->res->irq, sdw_cdns_irq,
 			sdw_cdns_thread, IRQF_SHARED, KBUILD_MODNAME,
@@ -309,8 +819,18 @@ static int intel_probe(struct platform_device *pdev)
 		goto err_init;
 	}
 
+	/* Register DAIs */
+	ret = intel_register_dai(sdw);
+	if (ret) {
+		dev_err(sdw->cdns.dev, "DAI registration failed: %d", ret);
+		snd_soc_unregister_component(sdw->cdns.dev);
+		goto err_dai;
+	}
+
 	return 0;
 
+err_dai:
+	free_irq(sdw->res->irq, sdw);
 err_init:
 	sdw_delete_bus_master(&sdw->cdns.bus);
 err_master_reg:
@@ -324,6 +844,7 @@ static int intel_remove(struct platform_device *pdev)
 	sdw = platform_get_drvdata(pdev);
 
 	free_irq(sdw->res->irq, sdw);
+	snd_soc_unregister_component(sdw->cdns.dev);
 	sdw_delete_bus_master(&sdw->cdns.bus);
 
 	return 0;

drivers/soundwire/intel.h

@@ -10,6 +10,8 @@
  * @shim: Audio shim pointer
  * @alh: ALH (Audio Link Hub) pointer
  * @irq: Interrupt line
+ * @ops: Shim callback ops
+ * @arg: Shim callback ops argument
  *
  * This is set as pdata for each link instance.
  */
@@ -18,6 +20,8 @@ struct sdw_intel_link_res {
 	void __iomem *shim;
 	void __iomem *alh;
 	int irq;
+	const struct sdw_intel_ops *ops;
+	void *arg;
 };
 
 #endif /* __SDW_INTEL_LOCAL_H */

drivers/soundwire/intel_init.c

@@ -111,6 +111,9 @@ static struct sdw_intel_ctx
 		link->res.shim = res->mmio_base + SDW_SHIM_BASE;
 		link->res.alh = res->mmio_base + SDW_ALH_BASE;
 
+		link->res.ops = res->ops;
+		link->res.arg = res->arg;
+
 		memset(&pdevinfo, 0, sizeof(pdevinfo));
 
 		pdevinfo.parent = res->parent;

drivers/soundwire/stream.c

@@ -0,0 +1,1479 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+// Copyright(c) 2015-18 Intel Corporation.
+
+/*
+ *  stream.c - SoundWire Bus stream operations.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/slab.h>
+#include <linux/soundwire/sdw_registers.h>
+#include <linux/soundwire/sdw.h>
+#include "bus.h"
+
+/*
+ * Array of supported rows and columns as per MIPI SoundWire Specification 1.1
+ *
+ * The rows are arranged as per the array index value programmed
+ * in register. The index 15 has dummy value 0 in order to fill hole.
+ */
+int rows[SDW_FRAME_ROWS] = {48, 50, 60, 64, 75, 80, 125, 147,
+			96, 100, 120, 128, 150, 160, 250, 0,
+			192, 200, 240, 256, 72, 144, 90, 180};
+
+int cols[SDW_FRAME_COLS] = {2, 4, 6, 8, 10, 12, 14, 16};
+
+static int sdw_find_col_index(int col)
+{
+	int i;
+
+	for (i = 0; i < SDW_FRAME_COLS; i++) {
+		if (cols[i] == col)
+			return i;
+	}
+
+	pr_warn("Requested column not found, selecting lowest column no: 2\n");
+	return 0;
+}
+
+static int sdw_find_row_index(int row)
+{
+	int i;
+
+	for (i = 0; i < SDW_FRAME_ROWS; i++) {
+		if (rows[i] == row)
+			return i;
+	}
+
+	pr_warn("Requested row not found, selecting lowest row no: 48\n");
+	return 0;
+}
+static int _sdw_program_slave_port_params(struct sdw_bus *bus,
+				struct sdw_slave *slave,
+				struct sdw_transport_params *t_params,
+				enum sdw_dpn_type type)
+{
+	u32 addr1, addr2, addr3, addr4;
+	int ret;
+	u16 wbuf;
+
+	if (bus->params.next_bank) {
+		addr1 = SDW_DPN_OFFSETCTRL2_B1(t_params->port_num);
+		addr2 = SDW_DPN_BLOCKCTRL3_B1(t_params->port_num);
+		addr3 = SDW_DPN_SAMPLECTRL2_B1(t_params->port_num);
+		addr4 = SDW_DPN_HCTRL_B1(t_params->port_num);
+	} else {
+		addr1 = SDW_DPN_OFFSETCTRL2_B0(t_params->port_num);
+		addr2 = SDW_DPN_BLOCKCTRL3_B0(t_params->port_num);
+		addr3 = SDW_DPN_SAMPLECTRL2_B0(t_params->port_num);
+		addr4 = SDW_DPN_HCTRL_B0(t_params->port_num);
+	}
+
+	/* Program DPN_OffsetCtrl2 registers */
+	ret = sdw_write(slave, addr1, t_params->offset2);
+	if (ret < 0) {
+		dev_err(bus->dev, "DPN_OffsetCtrl2 register write failed");
+		return ret;
+	}
+
+	/* Program DPN_BlockCtrl3 register */
+	ret = sdw_write(slave, addr2, t_params->blk_pkg_mode);
+	if (ret < 0) {
+		dev_err(bus->dev, "DPN_BlockCtrl3 register write failed");
+		return ret;
+	}
+
+	/*
+	 * Data ports are FULL, SIMPLE and REDUCED. This function handles
+	 * FULL and REDUCED only and and beyond this point only FULL is
+	 * handled, so bail out if we are not FULL data port type
+	 */
+	if (type != SDW_DPN_FULL)
+		return ret;
+
+	/* Program DPN_SampleCtrl2 register */
+	wbuf = (t_params->sample_interval - 1);
+	wbuf &= SDW_DPN_SAMPLECTRL_HIGH;
+	wbuf >>= SDW_REG_SHIFT(SDW_DPN_SAMPLECTRL_HIGH);
+
+	ret = sdw_write(slave, addr3, wbuf);
+	if (ret < 0) {
+		dev_err(bus->dev, "DPN_SampleCtrl2 register write failed");
+		return ret;
+	}
+
+	/* Program DPN_HCtrl register */
+	wbuf = t_params->hstart;
+	wbuf <<= SDW_REG_SHIFT(SDW_DPN_HCTRL_HSTART);
+	wbuf |= t_params->hstop;
+
+	ret = sdw_write(slave, addr4, wbuf);
+	if (ret < 0)
+		dev_err(bus->dev, "DPN_HCtrl register write failed");
+
+	return ret;
+}
+
+static int sdw_program_slave_port_params(struct sdw_bus *bus,
+			struct sdw_slave_runtime *s_rt,
+			struct sdw_port_runtime *p_rt)
+{
+	struct sdw_transport_params *t_params = &p_rt->transport_params;
+	struct sdw_port_params *p_params = &p_rt->port_params;
+	struct sdw_slave_prop *slave_prop = &s_rt->slave->prop;
+	u32 addr1, addr2, addr3, addr4, addr5, addr6;
+	struct sdw_dpn_prop *dpn_prop;
+	int ret;
+	u8 wbuf;
+
+	dpn_prop = sdw_get_slave_dpn_prop(s_rt->slave,
+					s_rt->direction,
+					t_params->port_num);
+	if (!dpn_prop)
+		return -EINVAL;
+
+	addr1 = SDW_DPN_PORTCTRL(t_params->port_num);
+	addr2 = SDW_DPN_BLOCKCTRL1(t_params->port_num);
+
+	if (bus->params.next_bank) {
+		addr3 = SDW_DPN_SAMPLECTRL1_B1(t_params->port_num);
+		addr4 = SDW_DPN_OFFSETCTRL1_B1(t_params->port_num);
+		addr5 = SDW_DPN_BLOCKCTRL2_B1(t_params->port_num);
+		addr6 = SDW_DPN_LANECTRL_B1(t_params->port_num);
+
+	} else {
+		addr3 = SDW_DPN_SAMPLECTRL1_B0(t_params->port_num);
+		addr4 = SDW_DPN_OFFSETCTRL1_B0(t_params->port_num);
+		addr5 = SDW_DPN_BLOCKCTRL2_B0(t_params->port_num);
+		addr6 = SDW_DPN_LANECTRL_B0(t_params->port_num);
+	}
+
+	/* Program DPN_PortCtrl register */
+	wbuf = p_params->data_mode << SDW_REG_SHIFT(SDW_DPN_PORTCTRL_DATAMODE);
+	wbuf |= p_params->flow_mode;
+
+	ret = sdw_update(s_rt->slave, addr1, 0xF, wbuf);
+	if (ret < 0) {
+		dev_err(&s_rt->slave->dev,
+			"DPN_PortCtrl register write failed for port %d",
+			t_params->port_num);
+		return ret;
+	}
+
+	/* Program DPN_BlockCtrl1 register */
+	ret = sdw_write(s_rt->slave, addr2, (p_params->bps - 1));
+	if (ret < 0) {
+		dev_err(&s_rt->slave->dev,
+			"DPN_BlockCtrl1 register write failed for port %d",
+			t_params->port_num);
+		return ret;
+	}
+
+	/* Program DPN_SampleCtrl1 register */
+	wbuf = (t_params->sample_interval - 1) & SDW_DPN_SAMPLECTRL_LOW;
+	ret = sdw_write(s_rt->slave, addr3, wbuf);
+	if (ret < 0) {
+		dev_err(&s_rt->slave->dev,
+			"DPN_SampleCtrl1 register write failed for port %d",
+			t_params->port_num);
+		return ret;
+	}
+
+	/* Program DPN_OffsetCtrl1 registers */
+	ret = sdw_write(s_rt->slave, addr4, t_params->offset1);
+	if (ret < 0) {
+		dev_err(&s_rt->slave->dev,
+			"DPN_OffsetCtrl1 register write failed for port %d",
+			t_params->port_num);
+		return ret;
+	}
+
+	/* Program DPN_BlockCtrl2 register*/
+	if (t_params->blk_grp_ctrl_valid) {
+		ret = sdw_write(s_rt->slave, addr5, t_params->blk_grp_ctrl);
+		if (ret < 0) {
+			dev_err(&s_rt->slave->dev,
+				"DPN_BlockCtrl2 reg write failed for port %d",
+				t_params->port_num);
+			return ret;
+		}
+	}
+
+	/* program DPN_LaneCtrl register */
+	if (slave_prop->lane_control_support) {
+		ret = sdw_write(s_rt->slave, addr6, t_params->lane_ctrl);
+		if (ret < 0) {
+			dev_err(&s_rt->slave->dev,
+				"DPN_LaneCtrl register write failed for port %d",
+				t_params->port_num);
+			return ret;
+		}
+	}
+
+	if (dpn_prop->type != SDW_DPN_SIMPLE) {
+		ret = _sdw_program_slave_port_params(bus, s_rt->slave,
+						t_params, dpn_prop->type);
+		if (ret < 0)
+			dev_err(&s_rt->slave->dev,
+				"Transport reg write failed for port: %d",
+				t_params->port_num);
+	}
+
+	return ret;
+}
+
+static int sdw_program_master_port_params(struct sdw_bus *bus,
+		struct sdw_port_runtime *p_rt)
+{
+	int ret;
+
+	/*
+	 * we need to set transport and port parameters for the port.
+	 * Transport parameters refers to the smaple interval, offsets and
+	 * hstart/stop etc of the data. Port parameters refers to word
+	 * length, flow mode etc of the port
+	 */
+	ret = bus->port_ops->dpn_set_port_transport_params(bus,
+					&p_rt->transport_params,
+					bus->params.next_bank);
+	if (ret < 0)
+		return ret;
+
+	return bus->port_ops->dpn_set_port_params(bus,
+				&p_rt->port_params,
+				bus->params.next_bank);
+}
+
+/**
+ * sdw_program_port_params() - Programs transport parameters of Master(s)
+ * and Slave(s)
+ *
+ * @m_rt: Master stream runtime
+ */
+static int sdw_program_port_params(struct sdw_master_runtime *m_rt)
+{
+	struct sdw_slave_runtime *s_rt = NULL;
+	struct sdw_bus *bus = m_rt->bus;
+	struct sdw_port_runtime *p_rt;
+	int ret = 0;
+
+	/* Program transport & port parameters for Slave(s) */
+	list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+		list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
+			ret = sdw_program_slave_port_params(bus, s_rt, p_rt);
+			if (ret < 0)
+				return ret;
+		}
+	}
+
+	/* Program transport & port parameters for Master(s) */
+	list_for_each_entry(p_rt, &m_rt->port_list, port_node) {
+		ret = sdw_program_master_port_params(bus, p_rt);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * sdw_enable_disable_slave_ports: Enable/disable slave data port
+ *
+ * @bus: bus instance
+ * @s_rt: slave runtime
+ * @p_rt: port runtime
+ * @en: enable or disable operation
+ *
+ * This function only sets the enable/disable bits in the relevant bank, the
+ * actual enable/disable is done with a bank switch
+ */
+static int sdw_enable_disable_slave_ports(struct sdw_bus *bus,
+				struct sdw_slave_runtime *s_rt,
+				struct sdw_port_runtime *p_rt, bool en)
+{
+	struct sdw_transport_params *t_params = &p_rt->transport_params;
+	u32 addr;
+	int ret;
+
+	if (bus->params.next_bank)
+		addr = SDW_DPN_CHANNELEN_B1(p_rt->num);
+	else
+		addr = SDW_DPN_CHANNELEN_B0(p_rt->num);
+
+	/*
+	 * Since bus doesn't support sharing a port across two streams,
+	 * it is safe to reset this register
+	 */
+	if (en)
+		ret = sdw_update(s_rt->slave, addr, 0xFF, p_rt->ch_mask);
+	else
+		ret = sdw_update(s_rt->slave, addr, 0xFF, 0x0);
+
+	if (ret < 0)
+		dev_err(&s_rt->slave->dev,
+			"Slave chn_en reg write failed:%d port:%d",
+			ret, t_params->port_num);
+
+	return ret;
+}
+
+static int sdw_enable_disable_master_ports(struct sdw_master_runtime *m_rt,
+			struct sdw_port_runtime *p_rt, bool en)
+{
+	struct sdw_transport_params *t_params = &p_rt->transport_params;
+	struct sdw_bus *bus = m_rt->bus;
+	struct sdw_enable_ch enable_ch;
+	int ret = 0;
+
+	enable_ch.port_num = p_rt->num;
+	enable_ch.ch_mask = p_rt->ch_mask;
+	enable_ch.enable = en;
+
+	/* Perform Master port channel(s) enable/disable */
+	if (bus->port_ops->dpn_port_enable_ch) {
+		ret = bus->port_ops->dpn_port_enable_ch(bus,
+				&enable_ch, bus->params.next_bank);
+		if (ret < 0) {
+			dev_err(bus->dev,
+				"Master chn_en write failed:%d port:%d",
+				ret, t_params->port_num);
+			return ret;
+		}
+	} else {
+		dev_err(bus->dev,
+			"dpn_port_enable_ch not supported, %s failed\n",
+			en ? "enable" : "disable");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * sdw_enable_disable_ports() - Enable/disable port(s) for Master and
+ * Slave(s)
+ *
+ * @m_rt: Master stream runtime
+ * @en: mode (enable/disable)
+ */
+static int sdw_enable_disable_ports(struct sdw_master_runtime *m_rt, bool en)
+{
+	struct sdw_port_runtime *s_port, *m_port;
+	struct sdw_slave_runtime *s_rt = NULL;
+	int ret = 0;
+
+	/* Enable/Disable Slave port(s) */
+	list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+		list_for_each_entry(s_port, &s_rt->port_list, port_node) {
+			ret = sdw_enable_disable_slave_ports(m_rt->bus, s_rt,
+							s_port, en);
+			if (ret < 0)
+				return ret;
+		}
+	}
+
+	/* Enable/Disable Master port(s) */
+	list_for_each_entry(m_port, &m_rt->port_list, port_node) {
+		ret = sdw_enable_disable_master_ports(m_rt, m_port, en);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int sdw_do_port_prep(struct sdw_slave_runtime *s_rt,
+		struct sdw_prepare_ch prep_ch, enum sdw_port_prep_ops cmd)
+{
+	const struct sdw_slave_ops *ops = s_rt->slave->ops;
+	int ret;
+
+	if (ops->port_prep) {
+		ret = ops->port_prep(s_rt->slave, &prep_ch, cmd);
+		if (ret < 0) {
+			dev_err(&s_rt->slave->dev,
+				"Slave Port Prep cmd %d failed: %d", cmd, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int sdw_prep_deprep_slave_ports(struct sdw_bus *bus,
+			struct sdw_slave_runtime *s_rt,
+			struct sdw_port_runtime *p_rt, bool prep)
+{
+	struct completion *port_ready = NULL;
+	struct sdw_dpn_prop *dpn_prop;
+	struct sdw_prepare_ch prep_ch;
+	unsigned int time_left;
+	bool intr = false;
+	int ret = 0, val;
+	u32 addr;
+
+	prep_ch.num = p_rt->num;
+	prep_ch.ch_mask = p_rt->ch_mask;
+
+	dpn_prop = sdw_get_slave_dpn_prop(s_rt->slave,
+					s_rt->direction,
+					prep_ch.num);
+	if (!dpn_prop) {
+		dev_err(bus->dev,
+			"Slave Port:%d properties not found", prep_ch.num);
+		return -EINVAL;
+	}
+
+	prep_ch.prepare = prep;
+
+	prep_ch.bank = bus->params.next_bank;
+
+	if (dpn_prop->device_interrupts || !dpn_prop->simple_ch_prep_sm)
+		intr = true;
+
+	/*
+	 * Enable interrupt before Port prepare.
+	 * For Port de-prepare, it is assumed that port
+	 * was prepared earlier
+	 */
+	if (prep && intr) {
+		ret = sdw_configure_dpn_intr(s_rt->slave, p_rt->num, prep,
+						dpn_prop->device_interrupts);
+		if (ret < 0)
+			return ret;
+	}
+
+	/* Inform slave about the impending port prepare */
+	sdw_do_port_prep(s_rt, prep_ch, SDW_OPS_PORT_PRE_PREP);
+
+	/* Prepare Slave port implementing CP_SM */
+	if (!dpn_prop->simple_ch_prep_sm) {
+		addr = SDW_DPN_PREPARECTRL(p_rt->num);
+
+		if (prep)
+			ret = sdw_update(s_rt->slave, addr,
+					0xFF, p_rt->ch_mask);
+		else
+			ret = sdw_update(s_rt->slave, addr, 0xFF, 0x0);
+
+		if (ret < 0) {
+			dev_err(&s_rt->slave->dev,
+				"Slave prep_ctrl reg write failed");
+			return ret;
+		}
+
+		/* Wait for completion on port ready */
+		port_ready = &s_rt->slave->port_ready[prep_ch.num];
+		time_left = wait_for_completion_timeout(port_ready,
+				msecs_to_jiffies(dpn_prop->ch_prep_timeout));
+
+		val = sdw_read(s_rt->slave, SDW_DPN_PREPARESTATUS(p_rt->num));
+		val &= p_rt->ch_mask;
+		if (!time_left || val) {
+			dev_err(&s_rt->slave->dev,
+				"Chn prep failed for port:%d", prep_ch.num);
+			return -ETIMEDOUT;
+		}
+	}
+
+	/* Inform slaves about ports prepared */
+	sdw_do_port_prep(s_rt, prep_ch, SDW_OPS_PORT_POST_PREP);
+
+	/* Disable interrupt after Port de-prepare */
+	if (!prep && intr)
+		ret = sdw_configure_dpn_intr(s_rt->slave, p_rt->num, prep,
+						dpn_prop->device_interrupts);
+
+	return ret;
+}
+
+static int sdw_prep_deprep_master_ports(struct sdw_master_runtime *m_rt,
+				struct sdw_port_runtime *p_rt, bool prep)
+{
+	struct sdw_transport_params *t_params = &p_rt->transport_params;
+	struct sdw_bus *bus = m_rt->bus;
+	const struct sdw_master_port_ops *ops = bus->port_ops;
+	struct sdw_prepare_ch prep_ch;
+	int ret = 0;
+
+	prep_ch.num = p_rt->num;
+	prep_ch.ch_mask = p_rt->ch_mask;
+	prep_ch.prepare = prep; /* Prepare/De-prepare */
+	prep_ch.bank = bus->params.next_bank;
+
+	/* Pre-prepare/Pre-deprepare port(s) */
+	if (ops->dpn_port_prep) {
+		ret = ops->dpn_port_prep(bus, &prep_ch);
+		if (ret < 0) {
+			dev_err(bus->dev, "Port prepare failed for port:%d",
+					t_params->port_num);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+/**
+ * sdw_prep_deprep_ports() - Prepare/De-prepare port(s) for Master(s) and
+ * Slave(s)
+ *
+ * @m_rt: Master runtime handle
+ * @prep: Prepare or De-prepare
+ */
+static int sdw_prep_deprep_ports(struct sdw_master_runtime *m_rt, bool prep)
+{
+	struct sdw_slave_runtime *s_rt = NULL;
+	struct sdw_port_runtime *p_rt;
+	int ret = 0;
+
+	/* Prepare/De-prepare Slave port(s) */
+	list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+		list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
+			ret = sdw_prep_deprep_slave_ports(m_rt->bus, s_rt,
+							p_rt, prep);
+			if (ret < 0)
+				return ret;
+		}
+	}
+
+	/* Prepare/De-prepare Master port(s) */
+	list_for_each_entry(p_rt, &m_rt->port_list, port_node) {
+		ret = sdw_prep_deprep_master_ports(m_rt, p_rt, prep);
+		if (ret < 0)
+			return ret;
+	}
+
+	return ret;
+}
+
+/**
+ * sdw_notify_config() - Notify bus configuration
+ *
+ * @m_rt: Master runtime handle
+ *
+ * This function notifies the Master(s) and Slave(s) of the
+ * new bus configuration.
+ */
+static int sdw_notify_config(struct sdw_master_runtime *m_rt)
+{
+	struct sdw_slave_runtime *s_rt;
+	struct sdw_bus *bus = m_rt->bus;
+	struct sdw_slave *slave;
+	int ret = 0;
+
+	if (bus->ops->set_bus_conf) {
+		ret = bus->ops->set_bus_conf(bus, &bus->params);
+		if (ret < 0)
+			return ret;
+	}
+
+	list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+		slave = s_rt->slave;
+
+		if (slave->ops->bus_config) {
+			ret = slave->ops->bus_config(slave, &bus->params);
+			if (ret < 0)
+				dev_err(bus->dev, "Notify Slave: %d failed",
+								slave->dev_num);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+/**
+ * sdw_program_params() - Program transport and port parameters for Master(s)
+ * and Slave(s)
+ *
+ * @bus: SDW bus instance
+ */
+static int sdw_program_params(struct sdw_bus *bus)
+{
+	struct sdw_master_runtime *m_rt = NULL;
+	int ret = 0;
+
+	list_for_each_entry(m_rt, &bus->m_rt_list, bus_node) {
+		ret = sdw_program_port_params(m_rt);
+		if (ret < 0) {
+			dev_err(bus->dev,
+				"Program transport params failed: %d", ret);
+			return ret;
+		}
+
+		ret = sdw_notify_config(m_rt);
+		if (ret < 0) {
+			dev_err(bus->dev, "Notify bus config failed: %d", ret);
+			return ret;
+		}
+
+		/* Enable port(s) on alternate bank for all active streams */
+		if (m_rt->stream->state != SDW_STREAM_ENABLED)
+			continue;
+
+		ret = sdw_enable_disable_ports(m_rt, true);
+		if (ret < 0) {
+			dev_err(bus->dev, "Enable channel failed: %d", ret);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static int sdw_bank_switch(struct sdw_bus *bus)
+{
+	int col_index, row_index;
+	struct sdw_msg *wr_msg;
+	u8 *wbuf = NULL;
+	int ret = 0;
+	u16 addr;
+
+	wr_msg = kzalloc(sizeof(*wr_msg), GFP_KERNEL);
+	if (!wr_msg)
+		return -ENOMEM;
+
+	wbuf = kzalloc(sizeof(*wbuf), GFP_KERNEL);
+	if (!wbuf) {
+		ret = -ENOMEM;
+		goto error_1;
+	}
+
+	/* Get row and column index to program register */
+	col_index = sdw_find_col_index(bus->params.col);
+	row_index = sdw_find_row_index(bus->params.row);
+	wbuf[0] = col_index | (row_index << 3);
+
+	if (bus->params.next_bank)
+		addr = SDW_SCP_FRAMECTRL_B1;
+	else
+		addr = SDW_SCP_FRAMECTRL_B0;
+
+	sdw_fill_msg(wr_msg, NULL, addr, 1, SDW_BROADCAST_DEV_NUM,
+					SDW_MSG_FLAG_WRITE, wbuf);
+	wr_msg->ssp_sync = true;
+
+	ret = sdw_transfer(bus, wr_msg);
+	if (ret < 0) {
+		dev_err(bus->dev, "Slave frame_ctrl reg write failed");
+		goto error;
+	}
+
+	kfree(wr_msg);
+	kfree(wbuf);
+	bus->defer_msg.msg = NULL;
+	bus->params.curr_bank = !bus->params.curr_bank;
+	bus->params.next_bank = !bus->params.next_bank;
+
+	return 0;
+
+error:
+	kfree(wbuf);
+error_1:
+	kfree(wr_msg);
+	return ret;
+}
+
+static int do_bank_switch(struct sdw_stream_runtime *stream)
+{
+	struct sdw_master_runtime *m_rt = stream->m_rt;
+	const struct sdw_master_ops *ops;
+	struct sdw_bus *bus = m_rt->bus;
+	int ret = 0;
+
+	ops = bus->ops;
+
+	/* Pre-bank switch */
+	if (ops->pre_bank_switch) {
+		ret = ops->pre_bank_switch(bus);
+		if (ret < 0) {
+			dev_err(bus->dev, "Pre bank switch op failed: %d", ret);
+			return ret;
+		}
+	}
+
+	/* Bank switch */
+	ret = sdw_bank_switch(bus);
+	if (ret < 0) {
+		dev_err(bus->dev, "Bank switch failed: %d", ret);
+		return ret;
+	}
+
+	/* Post-bank switch */
+	if (ops->post_bank_switch) {
+		ret = ops->post_bank_switch(bus);
+		if (ret < 0) {
+			dev_err(bus->dev,
+					"Post bank switch op failed: %d", ret);
+		}
+	}
+
+	return ret;
+}
+
+/**
+ * sdw_release_stream() - Free the assigned stream runtime
+ *
+ * @stream: SoundWire stream runtime
+ *
+ * sdw_release_stream should be called only once per stream
+ */
+void sdw_release_stream(struct sdw_stream_runtime *stream)
+{
+	kfree(stream);
+}
+EXPORT_SYMBOL(sdw_release_stream);
+
+/**
+ * sdw_alloc_stream() - Allocate and return stream runtime
+ *
+ * @stream_name: SoundWire stream name
+ *
+ * Allocates a SoundWire stream runtime instance.
+ * sdw_alloc_stream should be called only once per stream. Typically
+ * invoked from ALSA/ASoC machine/platform driver.
+ */
+struct sdw_stream_runtime *sdw_alloc_stream(char *stream_name)
+{
+	struct sdw_stream_runtime *stream;
+
+	stream = kzalloc(sizeof(*stream), GFP_KERNEL);
+	if (!stream)
+		return NULL;
+
+	stream->name = stream_name;
+	stream->state = SDW_STREAM_ALLOCATED;
+
+	return stream;
+}
+EXPORT_SYMBOL(sdw_alloc_stream);
+
+/**
+ * sdw_alloc_master_rt() - Allocates and initialize Master runtime handle
+ *
+ * @bus: SDW bus instance
+ * @stream_config: Stream configuration
+ * @stream: Stream runtime handle.
+ *
+ * This function is to be called with bus_lock held.
+ */
+static struct sdw_master_runtime
+*sdw_alloc_master_rt(struct sdw_bus *bus,
+			struct sdw_stream_config *stream_config,
+			struct sdw_stream_runtime *stream)
+{
+	struct sdw_master_runtime *m_rt;
+
+	m_rt = stream->m_rt;
+
+	/*
+	 * check if Master is already allocated (as a result of Slave adding
+	 * it first), if so skip allocation and go to configure
+	 */
+	if (m_rt)
+		goto stream_config;
+
+	m_rt = kzalloc(sizeof(*m_rt), GFP_KERNEL);
+	if (!m_rt)
+		return NULL;
+
+	/* Initialization of Master runtime handle */
+	INIT_LIST_HEAD(&m_rt->port_list);
+	INIT_LIST_HEAD(&m_rt->slave_rt_list);
+	stream->m_rt = m_rt;
+
+	list_add_tail(&m_rt->bus_node, &bus->m_rt_list);
+
+stream_config:
+	m_rt->ch_count = stream_config->ch_count;
+	m_rt->bus = bus;
+	m_rt->stream = stream;
+	m_rt->direction = stream_config->direction;
+
+	return m_rt;
+}
+
+/**
+ * sdw_alloc_slave_rt() - Allocate and initialize Slave runtime handle.
+ *
+ * @slave: Slave handle
+ * @stream_config: Stream configuration
+ * @stream: Stream runtime handle
+ *
+ * This function is to be called with bus_lock held.
+ */
+static struct sdw_slave_runtime
+*sdw_alloc_slave_rt(struct sdw_slave *slave,
+			struct sdw_stream_config *stream_config,
+			struct sdw_stream_runtime *stream)
+{
+	struct sdw_slave_runtime *s_rt = NULL;
+
+	s_rt = kzalloc(sizeof(*s_rt), GFP_KERNEL);
+	if (!s_rt)
+		return NULL;
+
+	INIT_LIST_HEAD(&s_rt->port_list);
+	s_rt->ch_count = stream_config->ch_count;
+	s_rt->direction = stream_config->direction;
+	s_rt->slave = slave;
+
+	return s_rt;
+}
+
+static void sdw_master_port_release(struct sdw_bus *bus,
+			struct sdw_master_runtime *m_rt)
+{
+	struct sdw_port_runtime *p_rt, *_p_rt;
+
+	list_for_each_entry_safe(p_rt, _p_rt,
+			&m_rt->port_list, port_node) {
+		list_del(&p_rt->port_node);
+		kfree(p_rt);
+	}
+}
+
+static void sdw_slave_port_release(struct sdw_bus *bus,
+			struct sdw_slave *slave,
+			struct sdw_stream_runtime *stream)
+{
+	struct sdw_port_runtime *p_rt, *_p_rt;
+	struct sdw_master_runtime *m_rt = stream->m_rt;
+	struct sdw_slave_runtime *s_rt;
+
+	list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+		if (s_rt->slave != slave)
+			continue;
+
+		list_for_each_entry_safe(p_rt, _p_rt,
+				&s_rt->port_list, port_node) {
+			list_del(&p_rt->port_node);
+			kfree(p_rt);
+		}
+	}
+}
+
+/**
+ * sdw_release_slave_stream() - Free Slave(s) runtime handle
+ *
+ * @slave: Slave handle.
+ * @stream: Stream runtime handle.
+ *
+ * This function is to be called with bus_lock held.
+ */
+static void sdw_release_slave_stream(struct sdw_slave *slave,
+			struct sdw_stream_runtime *stream)
+{
+	struct sdw_slave_runtime *s_rt, *_s_rt;
+	struct sdw_master_runtime *m_rt = stream->m_rt;
+
+	/* Retrieve Slave runtime handle */
+	list_for_each_entry_safe(s_rt, _s_rt,
+			&m_rt->slave_rt_list, m_rt_node) {
+
+		if (s_rt->slave == slave) {
+			list_del(&s_rt->m_rt_node);
+			kfree(s_rt);
+			return;
+		}
+	}
+}
+
+/**
+ * sdw_release_master_stream() - Free Master runtime handle
+ *
+ * @stream: Stream runtime handle.
+ *
+ * This function is to be called with bus_lock held
+ * It frees the Master runtime handle and associated Slave(s) runtime
+ * handle. If this is called first then sdw_release_slave_stream() will have
+ * no effect as Slave(s) runtime handle would already be freed up.
+ */
+static void sdw_release_master_stream(struct sdw_stream_runtime *stream)
+{
+	struct sdw_master_runtime *m_rt = stream->m_rt;
+	struct sdw_slave_runtime *s_rt, *_s_rt;
+
+	list_for_each_entry_safe(s_rt, _s_rt,
+			&m_rt->slave_rt_list, m_rt_node)
+		sdw_stream_remove_slave(s_rt->slave, stream);
+
+	list_del(&m_rt->bus_node);
+}
+
+/**
+ * sdw_stream_remove_master() - Remove master from sdw_stream
+ *
+ * @bus: SDW Bus instance
+ * @stream: SoundWire stream
+ *
+ * This removes and frees port_rt and master_rt from a stream
+ */
+int sdw_stream_remove_master(struct sdw_bus *bus,
+		struct sdw_stream_runtime *stream)
+{
+	mutex_lock(&bus->bus_lock);
+
+	sdw_release_master_stream(stream);
+	sdw_master_port_release(bus, stream->m_rt);
+	stream->state = SDW_STREAM_RELEASED;
+	kfree(stream->m_rt);
+	stream->m_rt = NULL;
+
+	mutex_unlock(&bus->bus_lock);
+
+	return 0;
+}
+EXPORT_SYMBOL(sdw_stream_remove_master);
+
+/**
+ * sdw_stream_remove_slave() - Remove slave from sdw_stream
+ *
+ * @slave: SDW Slave instance
+ * @stream: SoundWire stream
+ *
+ * This removes and frees port_rt and slave_rt from a stream
+ */
+int sdw_stream_remove_slave(struct sdw_slave *slave,
+		struct sdw_stream_runtime *stream)
+{
+	mutex_lock(&slave->bus->bus_lock);
+
+	sdw_slave_port_release(slave->bus, slave, stream);
+	sdw_release_slave_stream(slave, stream);
+
+	mutex_unlock(&slave->bus->bus_lock);
+
+	return 0;
+}
+EXPORT_SYMBOL(sdw_stream_remove_slave);
+
+/**
+ * sdw_config_stream() - Configure the allocated stream
+ *
+ * @dev: SDW device
+ * @stream: SoundWire stream
+ * @stream_config: Stream configuration for audio stream
+ * @is_slave: is API called from Slave or Master
+ *
+ * This function is to be called with bus_lock held.
+ */
+static int sdw_config_stream(struct device *dev,
+		struct sdw_stream_runtime *stream,
+		struct sdw_stream_config *stream_config, bool is_slave)
+{
+	/*
+	 * Update the stream rate, channel and bps based on data
+	 * source. For more than one data source (multilink),
+	 * match the rate, bps, stream type and increment number of channels.
+	 *
+	 * If rate/bps is zero, it means the values are not set, so skip
+	 * comparison and allow the value to be set and stored in stream
+	 */
+	if (stream->params.rate &&
+			stream->params.rate != stream_config->frame_rate) {
+		dev_err(dev, "rate not matching, stream:%s", stream->name);
+		return -EINVAL;
+	}
+
+	if (stream->params.bps &&
+			stream->params.bps != stream_config->bps) {
+		dev_err(dev, "bps not matching, stream:%s", stream->name);
+		return -EINVAL;
+	}
+
+	stream->type = stream_config->type;
+	stream->params.rate = stream_config->frame_rate;
+	stream->params.bps = stream_config->bps;
+
+	/* TODO: Update this check during Device-device support */
+	if (is_slave)
+		stream->params.ch_count += stream_config->ch_count;
+
+	return 0;
+}
+
+static int sdw_is_valid_port_range(struct device *dev,
+				struct sdw_port_runtime *p_rt)
+{
+	if (!SDW_VALID_PORT_RANGE(p_rt->num)) {
+		dev_err(dev,
+			"SoundWire: Invalid port number :%d", p_rt->num);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static struct sdw_port_runtime *sdw_port_alloc(struct device *dev,
+				struct sdw_port_config *port_config,
+				int port_index)
+{
+	struct sdw_port_runtime *p_rt;
+
+	p_rt = kzalloc(sizeof(*p_rt), GFP_KERNEL);
+	if (!p_rt)
+		return NULL;
+
+	p_rt->ch_mask = port_config[port_index].ch_mask;
+	p_rt->num = port_config[port_index].num;
+
+	return p_rt;
+}
+
+static int sdw_master_port_config(struct sdw_bus *bus,
+			struct sdw_master_runtime *m_rt,
+			struct sdw_port_config *port_config,
+			unsigned int num_ports)
+{
+	struct sdw_port_runtime *p_rt;
+	int i;
+
+	/* Iterate for number of ports to perform initialization */
+	for (i = 0; i < num_ports; i++) {
+		p_rt = sdw_port_alloc(bus->dev, port_config, i);
+		if (!p_rt)
+			return -ENOMEM;
+
+		/*
+		 * TODO: Check port capabilities for requested
+		 * configuration (audio mode support)
+		 */
+
+		list_add_tail(&p_rt->port_node, &m_rt->port_list);
+	}
+
+	return 0;
+}
+
+static int sdw_slave_port_config(struct sdw_slave *slave,
+			struct sdw_slave_runtime *s_rt,
+			struct sdw_port_config *port_config,
+			unsigned int num_config)
+{
+	struct sdw_port_runtime *p_rt;
+	int i, ret;
+
+	/* Iterate for number of ports to perform initialization */
+	for (i = 0; i < num_config; i++) {
+		p_rt = sdw_port_alloc(&slave->dev, port_config, i);
+		if (!p_rt)
+			return -ENOMEM;
+
+		/*
+		 * TODO: Check valid port range as defined by DisCo/
+		 * slave
+		 */
+		ret = sdw_is_valid_port_range(&slave->dev, p_rt);
+		if (ret < 0) {
+			kfree(p_rt);
+			return ret;
+		}
+
+		/*
+		 * TODO: Check port capabilities for requested
+		 * configuration (audio mode support)
+		 */
+
+		list_add_tail(&p_rt->port_node, &s_rt->port_list);
+	}
+
+	return 0;
+}
+
+/**
+ * sdw_stream_add_master() - Allocate and add master runtime to a stream
+ *
+ * @bus: SDW Bus instance
+ * @stream_config: Stream configuration for audio stream
+ * @port_config: Port configuration for audio stream
+ * @num_ports: Number of ports
+ * @stream: SoundWire stream
+ */
+int sdw_stream_add_master(struct sdw_bus *bus,
+		struct sdw_stream_config *stream_config,
+		struct sdw_port_config *port_config,
+		unsigned int num_ports,
+		struct sdw_stream_runtime *stream)
+{
+	struct sdw_master_runtime *m_rt = NULL;
+	int ret;
+
+	mutex_lock(&bus->bus_lock);
+
+	m_rt = sdw_alloc_master_rt(bus, stream_config, stream);
+	if (!m_rt) {
+		dev_err(bus->dev,
+				"Master runtime config failed for stream:%s",
+				stream->name);
+		ret = -ENOMEM;
+		goto error;
+	}
+
+	ret = sdw_config_stream(bus->dev, stream, stream_config, false);
+	if (ret)
+		goto stream_error;
+
+	ret = sdw_master_port_config(bus, m_rt, port_config, num_ports);
+	if (ret)
+		goto stream_error;
+
+	stream->state = SDW_STREAM_CONFIGURED;
+
+stream_error:
+	sdw_release_master_stream(stream);
+error:
+	mutex_unlock(&bus->bus_lock);
+	return ret;
+}
+EXPORT_SYMBOL(sdw_stream_add_master);
+
+/**
+ * sdw_stream_add_slave() - Allocate and add master/slave runtime to a stream
+ *
+ * @slave: SDW Slave instance
+ * @stream_config: Stream configuration for audio stream
+ * @stream: SoundWire stream
+ * @port_config: Port configuration for audio stream
+ * @num_ports: Number of ports
+ */
+int sdw_stream_add_slave(struct sdw_slave *slave,
+		struct sdw_stream_config *stream_config,
+		struct sdw_port_config *port_config,
+		unsigned int num_ports,
+		struct sdw_stream_runtime *stream)
+{
+	struct sdw_slave_runtime *s_rt;
+	struct sdw_master_runtime *m_rt;
+	int ret;
+
+	mutex_lock(&slave->bus->bus_lock);
+
+	/*
+	 * If this API is invoked by Slave first then m_rt is not valid.
+	 * So, allocate m_rt and add Slave to it.
+	 */
+	m_rt = sdw_alloc_master_rt(slave->bus, stream_config, stream);
+	if (!m_rt) {
+		dev_err(&slave->dev,
+				"alloc master runtime failed for stream:%s",
+				stream->name);
+		ret = -ENOMEM;
+		goto error;
+	}
+
+	s_rt = sdw_alloc_slave_rt(slave, stream_config, stream);
+	if (!s_rt) {
+		dev_err(&slave->dev,
+				"Slave runtime config failed for stream:%s",
+				stream->name);
+		ret = -ENOMEM;
+		goto stream_error;
+	}
+
+	ret = sdw_config_stream(&slave->dev, stream, stream_config, true);
+	if (ret)
+		goto stream_error;
+
+	list_add_tail(&s_rt->m_rt_node, &m_rt->slave_rt_list);
+
+	ret = sdw_slave_port_config(slave, s_rt, port_config, num_ports);
+	if (ret)
+		goto stream_error;
+
+	stream->state = SDW_STREAM_CONFIGURED;
+	goto error;
+
+stream_error:
+	/*
+	 * we hit error so cleanup the stream, release all Slave(s) and
+	 * Master runtime
+	 */
+	sdw_release_master_stream(stream);
+error:
+	mutex_unlock(&slave->bus->bus_lock);
+	return ret;
+}
+EXPORT_SYMBOL(sdw_stream_add_slave);
+
+/**
+ * sdw_get_slave_dpn_prop() - Get Slave port capabilities
+ *
+ * @slave: Slave handle
+ * @direction: Data direction.
+ * @port_num: Port number
+ */
+struct sdw_dpn_prop *sdw_get_slave_dpn_prop(struct sdw_slave *slave,
+				enum sdw_data_direction direction,
+				unsigned int port_num)
+{
+	struct sdw_dpn_prop *dpn_prop;
+	u8 num_ports;
+	int i;
+
+	if (direction == SDW_DATA_DIR_TX) {
+		num_ports = hweight32(slave->prop.source_ports);
+		dpn_prop = slave->prop.src_dpn_prop;
+	} else {
+		num_ports = hweight32(slave->prop.sink_ports);
+		dpn_prop = slave->prop.sink_dpn_prop;
+	}
+
+	for (i = 0; i < num_ports; i++) {
+		dpn_prop = &dpn_prop[i];
+
+		if (dpn_prop->num == port_num)
+			return &dpn_prop[i];
+	}
+
+	return NULL;
+}
+
+static int _sdw_prepare_stream(struct sdw_stream_runtime *stream)
+{
+	struct sdw_master_runtime *m_rt = stream->m_rt;
+	struct sdw_bus *bus = m_rt->bus;
+	struct sdw_master_prop *prop = NULL;
+	struct sdw_bus_params params;
+	int ret;
+
+	prop = &bus->prop;
+	memcpy(&params, &bus->params, sizeof(params));
+
+	/* TODO: Support Asynchronous mode */
+	if ((prop->max_freq % stream->params.rate) != 0) {
+		dev_err(bus->dev, "Async mode not supported");
+		return -EINVAL;
+	}
+
+	/* Increment cumulative bus bandwidth */
+	/* TODO: Update this during Device-Device support */
+	bus->params.bandwidth += m_rt->stream->params.rate *
+		m_rt->ch_count * m_rt->stream->params.bps;
+
+	/* Program params */
+	ret = sdw_program_params(bus);
+	if (ret < 0) {
+		dev_err(bus->dev, "Program params failed: %d", ret);
+		goto restore_params;
+	}
+
+	ret = do_bank_switch(stream);
+	if (ret < 0) {
+		dev_err(bus->dev, "Bank switch failed: %d", ret);
+		goto restore_params;
+	}
+
+	/* Prepare port(s) on the new clock configuration */
+	ret = sdw_prep_deprep_ports(m_rt, true);
+	if (ret < 0) {
+		dev_err(bus->dev, "Prepare port(s) failed ret = %d",
+				ret);
+		return ret;
+	}
+
+	stream->state = SDW_STREAM_PREPARED;
+
+	return ret;
+
+restore_params:
+	memcpy(&bus->params, &params, sizeof(params));
+	return ret;
+}
+
+/**
+ * sdw_prepare_stream() - Prepare SoundWire stream
+ *
+ * @stream: Soundwire stream
+ *
+ * Documentation/soundwire/stream.txt explains this API in detail
+ */
+int sdw_prepare_stream(struct sdw_stream_runtime *stream)
+{
+	int ret = 0;
+
+	if (!stream) {
+		pr_err("SoundWire: Handle not found for stream");
+		return -EINVAL;
+	}
+
+	mutex_lock(&stream->m_rt->bus->bus_lock);
+
+	ret = _sdw_prepare_stream(stream);
+	if (ret < 0)
+		pr_err("Prepare for stream:%s failed: %d", stream->name, ret);
+
+	mutex_unlock(&stream->m_rt->bus->bus_lock);
+	return ret;
+}
+EXPORT_SYMBOL(sdw_prepare_stream);
+
+static int _sdw_enable_stream(struct sdw_stream_runtime *stream)
+{
+	struct sdw_master_runtime *m_rt = stream->m_rt;
+	struct sdw_bus *bus = m_rt->bus;
+	int ret;
+
+	/* Program params */
+	ret = sdw_program_params(bus);
+	if (ret < 0) {
+		dev_err(bus->dev, "Program params failed: %d", ret);
+		return ret;
+	}
+
+	/* Enable port(s) */
+	ret = sdw_enable_disable_ports(m_rt, true);
+	if (ret < 0) {
+		dev_err(bus->dev, "Enable port(s) failed ret: %d", ret);
+		return ret;
+	}
+
+	ret = do_bank_switch(stream);
+	if (ret < 0) {
+		dev_err(bus->dev, "Bank switch failed: %d", ret);
+		return ret;
+	}
+
+	stream->state = SDW_STREAM_ENABLED;
+	return 0;
+}
+
+/**
+ * sdw_enable_stream() - Enable SoundWire stream
+ *
+ * @stream: Soundwire stream
+ *
+ * Documentation/soundwire/stream.txt explains this API in detail
+ */
+int sdw_enable_stream(struct sdw_stream_runtime *stream)
+{
+	int ret = 0;
+
+	if (!stream) {
+		pr_err("SoundWire: Handle not found for stream");
+		return -EINVAL;
+	}
+
+	mutex_lock(&stream->m_rt->bus->bus_lock);
+
+	ret = _sdw_enable_stream(stream);
+	if (ret < 0)
+		pr_err("Enable for stream:%s failed: %d", stream->name, ret);
+
+	mutex_unlock(&stream->m_rt->bus->bus_lock);
+	return ret;
+}
+EXPORT_SYMBOL(sdw_enable_stream);
+
+static int _sdw_disable_stream(struct sdw_stream_runtime *stream)
+{
+	struct sdw_master_runtime *m_rt = stream->m_rt;
+	struct sdw_bus *bus = m_rt->bus;
+	int ret;
+
+	/* Disable port(s) */
+	ret = sdw_enable_disable_ports(m_rt, false);
+	if (ret < 0) {
+		dev_err(bus->dev, "Disable port(s) failed: %d", ret);
+		return ret;
+	}
+
+	stream->state = SDW_STREAM_DISABLED;
+
+	/* Program params */
+	ret = sdw_program_params(bus);
+	if (ret < 0) {
+		dev_err(bus->dev, "Program params failed: %d", ret);
+		return ret;
+	}
+
+	return do_bank_switch(stream);
+}
+
+/**
+ * sdw_disable_stream() - Disable SoundWire stream
+ *
+ * @stream: Soundwire stream
+ *
+ * Documentation/soundwire/stream.txt explains this API in detail
+ */
+int sdw_disable_stream(struct sdw_stream_runtime *stream)
+{
+	int ret = 0;
+
+	if (!stream) {
+		pr_err("SoundWire: Handle not found for stream");
+		return -EINVAL;
+	}
+
+	mutex_lock(&stream->m_rt->bus->bus_lock);
+
+	ret = _sdw_disable_stream(stream);
+	if (ret < 0)
+		pr_err("Disable for stream:%s failed: %d", stream->name, ret);
+
+	mutex_unlock(&stream->m_rt->bus->bus_lock);
+	return ret;
+}
+EXPORT_SYMBOL(sdw_disable_stream);
+
+static int _sdw_deprepare_stream(struct sdw_stream_runtime *stream)
+{
+	struct sdw_master_runtime *m_rt = stream->m_rt;
+	struct sdw_bus *bus = m_rt->bus;
+	int ret = 0;
+
+	/* De-prepare port(s) */
+	ret = sdw_prep_deprep_ports(m_rt, false);
+	if (ret < 0) {
+		dev_err(bus->dev, "De-prepare port(s) failed: %d", ret);
+		return ret;
+	}
+
+	stream->state = SDW_STREAM_DEPREPARED;
+
+	/* TODO: Update this during Device-Device support */
+	bus->params.bandwidth -= m_rt->stream->params.rate *
+		m_rt->ch_count * m_rt->stream->params.bps;
+
+	/* Program params */
+	ret = sdw_program_params(bus);
+	if (ret < 0) {
+		dev_err(bus->dev, "Program params failed: %d", ret);
+		return ret;
+	}
+
+	return do_bank_switch(stream);
+}
+
+/**
+ * sdw_deprepare_stream() - Deprepare SoundWire stream
+ *
+ * @stream: Soundwire stream
+ *
+ * Documentation/soundwire/stream.txt explains this API in detail
+ */
+int sdw_deprepare_stream(struct sdw_stream_runtime *stream)
+{
+	int ret = 0;
+
+	if (!stream) {
+		pr_err("SoundWire: Handle not found for stream");
+		return -EINVAL;
+	}
+
+	mutex_lock(&stream->m_rt->bus->bus_lock);
+
+	ret = _sdw_deprepare_stream(stream);
+	if (ret < 0)
+		pr_err("De-prepare for stream:%d failed: %d", ret, ret);
+
+	mutex_unlock(&stream->m_rt->bus->bus_lock);
+	return ret;
+}
+EXPORT_SYMBOL(sdw_deprepare_stream);

include/linux/soundwire/sdw.h

@@ -23,9 +23,24 @@ struct sdw_slave;
 #define SDW_MASTER_DEV_NUM		14
 
 #define SDW_NUM_DEV_ID_REGISTERS	6
+/* frame shape defines */
 
+/*
+ * Note: The maximum row define in SoundWire spec 1.1 is 23. In order to
+ * fill hole with 0, one more dummy entry is added
+ */
+#define SDW_FRAME_ROWS		24
+#define SDW_FRAME_COLS		8
+#define SDW_FRAME_ROW_COLS		(SDW_FRAME_ROWS * SDW_FRAME_COLS)
+
+#define SDW_FRAME_CTRL_BITS		48
 #define SDW_MAX_DEVICES			11
 
+#define SDW_VALID_PORT_RANGE(n)		(n <= 14 && n >= 1)
+
+#define SDW_DAI_ID_RANGE_START		100
+#define SDW_DAI_ID_RANGE_END		200
+
 /**
  * enum sdw_slave_status - Slave status
  * @SDW_SLAVE_UNATTACHED: Slave is not attached with the bus.
@@ -61,6 +76,30 @@ enum sdw_command_response {
 	SDW_CMD_FAIL_OTHER = 4,
 };
 
+/**
+ * enum sdw_stream_type: data stream type
+ *
+ * @SDW_STREAM_PCM: PCM data stream
+ * @SDW_STREAM_PDM: PDM data stream
+ *
+ * spec doesn't define this, but is used in implementation
+ */
+enum sdw_stream_type {
+	SDW_STREAM_PCM = 0,
+	SDW_STREAM_PDM = 1,
+};
+
+/**
+ * enum sdw_data_direction: Data direction
+ *
+ * @SDW_DATA_DIR_RX: Data into Port
+ * @SDW_DATA_DIR_TX: Data out of Port
+ */
+enum sdw_data_direction {
+	SDW_DATA_DIR_RX = 0,
+	SDW_DATA_DIR_TX = 1,
+};
+
 /*
  * SDW properties, defined in MIPI DisCo spec v1.0
  */
@@ -341,11 +380,92 @@ struct sdw_slave_intr_status {
 };
 
 /**
- * struct sdw_slave_ops - Slave driver callback ops
+ * sdw_reg_bank - SoundWire register banks
+ * @SDW_BANK0: Soundwire register bank 0
+ * @SDW_BANK1: Soundwire register bank 1
+ */
+enum sdw_reg_bank {
+	SDW_BANK0,
+	SDW_BANK1,
+};
+
+/**
+ * struct sdw_bus_conf: Bus configuration
+ *
+ * @clk_freq: Clock frequency, in Hz
+ * @num_rows: Number of rows in frame
+ * @num_cols: Number of columns in frame
+ * @bank: Next register bank
+ */
+struct sdw_bus_conf {
+	unsigned int clk_freq;
+	unsigned int num_rows;
+	unsigned int num_cols;
+	unsigned int bank;
+};
+
+/**
+ * struct sdw_prepare_ch: Prepare/De-prepare Data Port channel
+ *
+ * @num: Port number
+ * @ch_mask: Active channel mask
+ * @prepare: Prepare (true) /de-prepare (false) channel
+ * @bank: Register bank, which bank Slave/Master driver should program for
+ * implementation defined registers. This is always updated to next_bank
+ * value read from bus params.
+ *
+ */
+struct sdw_prepare_ch {
+	unsigned int num;
+	unsigned int ch_mask;
+	bool prepare;
+	unsigned int bank;
+};
+
+/**
+ * enum sdw_port_prep_ops: Prepare operations for Data Port
+ *
+ * @SDW_OPS_PORT_PRE_PREP: Pre prepare operation for the Port
+ * @SDW_OPS_PORT_PREP: Prepare operation for the Port
+ * @SDW_OPS_PORT_POST_PREP: Post prepare operation for the Port
+ */
+enum sdw_port_prep_ops {
+	SDW_OPS_PORT_PRE_PREP = 0,
+	SDW_OPS_PORT_PREP = 1,
+	SDW_OPS_PORT_POST_PREP = 2,
+};
+
+/**
+ * struct sdw_bus_params: Structure holding bus configuration
+ *
+ * @curr_bank: Current bank in use (BANK0/BANK1)
+ * @next_bank: Next bank to use (BANK0/BANK1). next_bank will always be
+ * set to !curr_bank
+ * @max_dr_freq: Maximum double rate clock frequency supported, in Hz
+ * @curr_dr_freq: Current double rate clock frequency, in Hz
+ * @bandwidth: Current bandwidth
+ * @col: Active columns
+ * @row: Active rows
+ */
+struct sdw_bus_params {
+	enum sdw_reg_bank curr_bank;
+	enum sdw_reg_bank next_bank;
+	unsigned int max_dr_freq;
+	unsigned int curr_dr_freq;
+	unsigned int bandwidth;
+	unsigned int col;
+	unsigned int row;
+};
+
+/**
+ * struct sdw_slave_ops: Slave driver callback ops
+ *
  * @read_prop: Read Slave properties
  * @interrupt_callback: Device interrupt notification (invoked in thread
  * context)
  * @update_status: Update Slave status
+ * @bus_config: Update the bus config for Slave
+ * @port_prep: Prepare the port with parameters
  */
 struct sdw_slave_ops {
 	int (*read_prop)(struct sdw_slave *sdw);
@@ -353,6 +473,11 @@ struct sdw_slave_ops {
 			struct sdw_slave_intr_status *status);
 	int (*update_status)(struct sdw_slave *slave,
 			enum sdw_slave_status status);
+	int (*bus_config)(struct sdw_slave *slave,
+			struct sdw_bus_params *params);
+	int (*port_prep)(struct sdw_slave *slave,
+			struct sdw_prepare_ch *prepare_ch,
+			enum sdw_port_prep_ops pre_ops);
 };
 
 /**
@@ -406,6 +531,93 @@ int sdw_handle_slave_status(struct sdw_bus *bus,
  * SDW master structures and APIs
  */
 
+/**
+ * struct sdw_port_params: Data Port parameters
+ *
+ * @num: Port number
+ * @bps: Word length of the Port
+ * @flow_mode: Port Data flow mode
+ * @data_mode: Test modes or normal mode
+ *
+ * This is used to program the Data Port based on Data Port stream
+ * parameters.
+ */
+struct sdw_port_params {
+	unsigned int num;
+	unsigned int bps;
+	unsigned int flow_mode;
+	unsigned int data_mode;
+};
+
+/**
+ * struct sdw_transport_params: Data Port Transport Parameters
+ *
+ * @blk_grp_ctrl_valid: Port implements block group control
+ * @num: Port number
+ * @blk_grp_ctrl: Block group control value
+ * @sample_interval: Sample interval
+ * @offset1: Blockoffset of the payload data
+ * @offset2: Blockoffset of the payload data
+ * @hstart: Horizontal start of the payload data
+ * @hstop: Horizontal stop of the payload data
+ * @blk_pkg_mode: Block per channel or block per port
+ * @lane_ctrl: Data lane Port uses for Data transfer. Currently only single
+ * data lane is supported in bus
+ *
+ * This is used to program the Data Port based on Data Port transport
+ * parameters. All these parameters are banked and can be modified
+ * during a bank switch without any artifacts in audio stream.
+ */
+struct sdw_transport_params {
+	bool blk_grp_ctrl_valid;
+	unsigned int port_num;
+	unsigned int blk_grp_ctrl;
+	unsigned int sample_interval;
+	unsigned int offset1;
+	unsigned int offset2;
+	unsigned int hstart;
+	unsigned int hstop;
+	unsigned int blk_pkg_mode;
+	unsigned int lane_ctrl;
+};
+
+/**
+ * struct sdw_enable_ch: Enable/disable Data Port channel
+ *
+ * @num: Port number
+ * @ch_mask: Active channel mask
+ * @enable: Enable (true) /disable (false) channel
+ */
+struct sdw_enable_ch {
+	unsigned int port_num;
+	unsigned int ch_mask;
+	bool enable;
+};
+
+/**
+ * struct sdw_master_port_ops: Callback functions from bus to Master
+ * driver to set Master Data ports.
+ *
+ * @dpn_set_port_params: Set the Port parameters for the Master Port.
+ * Mandatory callback
+ * @dpn_set_port_transport_params: Set transport parameters for the Master
+ * Port. Mandatory callback
+ * @dpn_port_prep: Port prepare operations for the Master Data Port.
+ * @dpn_port_enable_ch: Enable the channels of Master Port.
+ */
+struct sdw_master_port_ops {
+	int (*dpn_set_port_params)(struct sdw_bus *bus,
+			struct sdw_port_params *port_params,
+			unsigned int bank);
+	int (*dpn_set_port_transport_params)(struct sdw_bus *bus,
+			struct sdw_transport_params *transport_params,
+			enum sdw_reg_bank bank);
+	int (*dpn_port_prep)(struct sdw_bus *bus,
+			struct sdw_prepare_ch *prepare_ch);
+	int (*dpn_port_enable_ch)(struct sdw_bus *bus,
+			struct sdw_enable_ch *enable_ch, unsigned int bank);
+};
+
 struct sdw_msg;
 
 /**
@@ -426,6 +638,9 @@ struct sdw_defer {
  * @xfer_msg: Transfer message callback
  * @xfer_msg_defer: Defer version of transfer message callback
  * @reset_page_addr: Reset the SCP page address registers
+ * @set_bus_conf: Set the bus configuration
+ * @pre_bank_switch: Callback for pre bank switch
+ * @post_bank_switch: Callback for post bank switch
  */
 struct sdw_master_ops {
 	int (*read_prop)(struct sdw_bus *bus);
@@ -437,6 +652,11 @@ struct sdw_master_ops {
 			struct sdw_defer *defer);
 	enum sdw_command_response (*reset_page_addr)
 			(struct sdw_bus *bus, unsigned int dev_num);
+	int (*set_bus_conf)(struct sdw_bus *bus,
+			struct sdw_bus_params *params);
+	int (*pre_bank_switch)(struct sdw_bus *bus);
+	int (*post_bank_switch)(struct sdw_bus *bus);
+
 };
 
 /**
@@ -449,9 +669,15 @@ struct sdw_master_ops {
  * @bus_lock: bus lock
  * @msg_lock: message lock
  * @ops: Master callback ops
+ * @port_ops: Master port callback ops
+ * @params: Current bus parameters
  * @prop: Master properties
+ * @m_rt_list: List of Master instance of all stream(s) running on Bus. This
+ * is used to compute and program bus bandwidth, clock, frame shape,
+ * transport and port parameters
  * @defer_msg: Defer message
  * @clk_stop_timeout: Clock stop timeout computed
+ * @bank_switch_timeout: Bank switch timeout computed
  */
 struct sdw_bus {
 	struct device *dev;
@@ -461,14 +687,118 @@ struct sdw_bus {
 	struct mutex bus_lock;
 	struct mutex msg_lock;
 	const struct sdw_master_ops *ops;
+	const struct sdw_master_port_ops *port_ops;
+	struct sdw_bus_params params;
 	struct sdw_master_prop prop;
+	struct list_head m_rt_list;
 	struct sdw_defer defer_msg;
 	unsigned int clk_stop_timeout;
+	u32 bank_switch_timeout;
 };
 
 int sdw_add_bus_master(struct sdw_bus *bus);
 void sdw_delete_bus_master(struct sdw_bus *bus);
 
+/**
+ * sdw_port_config: Master or Slave Port configuration
+ *
+ * @num: Port number
+ * @ch_mask: channels mask for port
+ */
+struct sdw_port_config {
+	unsigned int num;
+	unsigned int ch_mask;
+};
+
+/**
+ * sdw_stream_config: Master or Slave stream configuration
+ *
+ * @frame_rate: Audio frame rate of the stream, in Hz
+ * @ch_count: Channel count of the stream
+ * @bps: Number of bits per audio sample
+ * @direction: Data direction
+ * @type: Stream type PCM or PDM
+ */
+struct sdw_stream_config {
+	unsigned int frame_rate;
+	unsigned int ch_count;
+	unsigned int bps;
+	enum sdw_data_direction direction;
+	enum sdw_stream_type type;
+};
+
+/**
+ * sdw_stream_state: Stream states
+ *
+ * @SDW_STREAM_ALLOCATED: New stream allocated.
+ * @SDW_STREAM_CONFIGURED: Stream configured
+ * @SDW_STREAM_PREPARED: Stream prepared
+ * @SDW_STREAM_ENABLED: Stream enabled
+ * @SDW_STREAM_DISABLED: Stream disabled
+ * @SDW_STREAM_DEPREPARED: Stream de-prepared
+ * @SDW_STREAM_RELEASED: Stream released
+ */
+enum sdw_stream_state {
+	SDW_STREAM_ALLOCATED = 0,
+	SDW_STREAM_CONFIGURED = 1,
+	SDW_STREAM_PREPARED = 2,
+	SDW_STREAM_ENABLED = 3,
+	SDW_STREAM_DISABLED = 4,
+	SDW_STREAM_DEPREPARED = 5,
+	SDW_STREAM_RELEASED = 6,
+};
+
+/**
+ * sdw_stream_params: Stream parameters
+ *
+ * @rate: Sampling frequency, in Hz
+ * @ch_count: Number of channels
+ * @bps: bits per channel sample
+ */
+struct sdw_stream_params {
+	unsigned int rate;
+	unsigned int ch_count;
+	unsigned int bps;
+};
+
+/**
+ * sdw_stream_runtime: Runtime stream parameters
+ *
+ * @name: SoundWire stream name
+ * @params: Stream parameters
+ * @state: Current state of the stream
+ * @type: Stream type PCM or PDM
+ * @m_rt: Master runtime
+ */
+struct sdw_stream_runtime {
+	char *name;
+	struct sdw_stream_params params;
+	enum sdw_stream_state state;
+	enum sdw_stream_type type;
+	struct sdw_master_runtime *m_rt;
+};
+
+struct sdw_stream_runtime *sdw_alloc_stream(char *stream_name);
+void sdw_release_stream(struct sdw_stream_runtime *stream);
+int sdw_stream_add_master(struct sdw_bus *bus,
+		struct sdw_stream_config *stream_config,
+		struct sdw_port_config *port_config,
+		unsigned int num_ports,
+		struct sdw_stream_runtime *stream);
+int sdw_stream_add_slave(struct sdw_slave *slave,
+		struct sdw_stream_config *stream_config,
+		struct sdw_port_config *port_config,
+		unsigned int num_ports,
+		struct sdw_stream_runtime *stream);
+int sdw_stream_remove_master(struct sdw_bus *bus,
+		struct sdw_stream_runtime *stream);
+int sdw_stream_remove_slave(struct sdw_slave *slave,
+		struct sdw_stream_runtime *stream);
+int sdw_prepare_stream(struct sdw_stream_runtime *stream);
+int sdw_enable_stream(struct sdw_stream_runtime *stream);
+int sdw_disable_stream(struct sdw_stream_runtime *stream);
+int sdw_deprepare_stream(struct sdw_stream_runtime *stream);
+
 /* messaging and data APIs */
 
 int sdw_read(struct sdw_slave *slave, u32 addr);

include/linux/soundwire/sdw_intel.h

@@ -4,18 +4,32 @@
 #ifndef __SDW_INTEL_H
 #define __SDW_INTEL_H
 
+/**
+ * struct sdw_intel_ops: Intel audio driver callback ops
+ *
+ * @config_stream: configure the stream with the hw_params
+ */
+struct sdw_intel_ops {
+	int (*config_stream)(void *arg, void *substream,
+			void *dai, void *hw_params, int stream_num);
+};
+
 /**
  * struct sdw_intel_res - Soundwire Intel resource structure
  * @mmio_base: mmio base of SoundWire registers
  * @irq: interrupt number
  * @handle: ACPI parent handle
  * @parent: parent device
+ * @ops: callback ops
+ * @arg: callback arg
  */
 struct sdw_intel_res {
 	void __iomem *mmio_base;
 	int irq;
 	acpi_handle handle;
 	struct device *parent;
+	const struct sdw_intel_ops *ops;
+	void *arg;
 };
 
 void *sdw_intel_init(acpi_handle *parent_handle, struct sdw_intel_res *res);

include/sound/soc-dai.h

@@ -170,6 +170,8 @@ struct snd_soc_dai_ops {
 		unsigned int rx_num, unsigned int *rx_slot);
 	int (*set_tristate)(struct snd_soc_dai *dai, int tristate);
 
+	int (*set_sdw_stream)(struct snd_soc_dai *dai,
+			void *stream, int direction);
 	/*
 	 * DAI digital mute - optional.
 	 * Called by soc-core to minimise any pops.
@@ -358,4 +360,25 @@ static inline void *snd_soc_dai_get_drvdata(struct snd_soc_dai *dai)
 	return dev_get_drvdata(dai->dev);
 }
 
+/**
+ * snd_soc_dai_set_sdw_stream() - Configures a DAI for SDW stream operation
+ * @dai: DAI
+ * @stream: STREAM
+ * @direction: Stream direction(Playback/Capture)
+ * SoundWire subsystem doesn't have a notion of direction and we reuse
+ * the ASoC stream direction to configure sink/source ports.
+ * Playback maps to source ports and Capture for sink ports.
+ *
+ * This should be invoked with NULL to clear the stream set previously.
+ * Returns 0 on success, a negative error code otherwise.
+ */
+static inline int snd_soc_dai_set_sdw_stream(struct snd_soc_dai *dai,
+				void *stream, int direction)
+{
+	if (dai->driver->ops->set_sdw_stream)
+		return dai->driver->ops->set_sdw_stream(dai, stream, direction);
+	else
+		return -ENOTSUPP;
+}
+
 #endif