wil6210: fix printouts for better readability

Reshuffle prints to consolidate firmware/hardware information
report upon card init

Convert print for unhandled MISC ISR bits to "debug" - it is
normal situation and not an "error"

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/wil6210/interrupt.c

@@ -338,7 +338,7 @@ static irqreturn_t wil6210_irq_misc_thread(int irq, void *cookie)
 	}
 
 	if (isr)
-		wil_err(wil, "un-handled MISC ISR bits 0x%08x\n", isr);
+		wil_dbg_irq(wil, "un-handled MISC ISR bits 0x%08x\n", isr);
 
 	wil->isr_misc = 0;
 

drivers/net/wireless/ath/wil6210/main.c

@@ -363,8 +363,8 @@ static int wil_wait_for_fw_ready(struct wil6210_priv *wil)
 		wil_err(wil, "Firmware not ready\n");
 		return -ETIME;
 	} else {
-		wil_dbg_misc(wil, "FW ready after %d ms\n",
-			     jiffies_to_msecs(to-left));
+		wil_info(wil, "FW ready after %d ms. HW version 0x%08x\n",
+			 jiffies_to_msecs(to-left), wil->hw_version);
 	}
 	return 0;
 }

drivers/net/wireless/ath/wil6210/pcie_bus.c

@@ -74,8 +74,6 @@ static int wil_if_pcie_enable(struct wil6210_priv *wil)
 	if (rc)
 		goto release_irq;
 
-	wil_info(wil, "HW version: 0x%08x\n", wil->hw_version);
-
 	return 0;
 
  release_irq:

drivers/net/wireless/ath/wil6210/wmi.c

@@ -192,7 +192,7 @@ static int __wmi_send(struct wil6210_priv *wil, u16 cmdid, void *buf, u16 len)
 	might_sleep();
 
 	if (!test_bit(wil_status_fwready, &wil->status)) {
-		wil_err(wil, "FW not ready\n");
+		wil_err(wil, "WMI: cannot send command while FW not ready\n");
 		return -EAGAIN;
 	}
 
@@ -276,8 +276,8 @@ static void wmi_evt_ready(struct wil6210_priv *wil, int id, void *d, int len)
 	wil->fw_version = le32_to_cpu(evt->sw_version);
 	wil->n_mids = evt->numof_additional_mids;
 
-	wil_dbg_wmi(wil, "FW ver. %d; MAC %pM; %d MID's\n", wil->fw_version,
-		    evt->mac, wil->n_mids);
+	wil_info(wil, "FW ver. %d; MAC %pM; %d MID's\n", wil->fw_version,
+		 evt->mac, wil->n_mids);
 
 	if (!is_valid_ether_addr(ndev->dev_addr)) {
 		memcpy(ndev->dev_addr, evt->mac, ETH_ALEN);
@@ -290,7 +290,7 @@ static void wmi_evt_ready(struct wil6210_priv *wil, int id, void *d, int len)
 static void wmi_evt_fw_ready(struct wil6210_priv *wil, int id, void *d,
 			     int len)
 {
-	wil_dbg_wmi(wil, "WMI: FW ready\n");
+	wil_dbg_wmi(wil, "WMI: got FW ready event\n");
 
 	set_bit(wil_status_fwready, &wil->status);
 	/* reuse wmi_ready for the firmware ready indication */