arm64: dts: qcom: Fix broken interrupt trigger settings

When a device uses the GIC as its interrupt controller and generates
SPIs, only the values 1 (edge rising) and 4 (level high) are legal.

Anything else is just plain wrong (can't be programmed into the HW),
and leads to aborted driver probes (USB doesn't work with 4.8-rc1
on a Dragonboard 410C).

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -494,7 +494,7 @@
 			compatible = "qcom,ci-hdrc";
 			reg = <0x78d9000 0x400>;
 			dr_mode = "peripheral";
-			interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			usb-phy = <&usb_otg>;
 			status = "disabled";
 		};
@@ -502,7 +502,7 @@
 		usb_host: ehci@78d9000 {
 			compatible = "qcom,ehci-host";
 			reg = <0x78d9000 0x400>;
-			interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			usb-phy = <&usb_otg>;
 			status = "disabled";
 		};
@@ -510,8 +510,8 @@
 		usb_otg: phy@78d9000 {
 			compatible = "qcom,usb-otg-snps";
 			reg = <0x78d9000 0x400>;
-			interrupts = <GIC_SPI 134 IRQ_TYPE_EDGE_BOTH>,
-				     <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 
 			qcom,vdd-levels = <500000 1000000 1320000>;
 			qcom,phy-init-sequence = <0x44 0x6B 0x24 0x13>;
@@ -605,7 +605,7 @@
 			      <0x200a000 0x002100>;
 			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
 			interrupt-names = "periph_irq";
-			interrupts = <GIC_SPI 190 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
 			qcom,ee = <0>;
 			qcom,channel = <0>;
 			#address-cells = <2>;

arch/arm64/boot/dts/qcom/msm8996.dtsi

@@ -339,7 +339,7 @@
 			      <0x400a000 0x002100>;
 			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
 			interrupt-names = "periph_irq";
-			interrupts = <GIC_SPI 326 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
 			qcom,ee = <0>;
 			qcom,channel = <0>;
 			#address-cells = <2>;