Merge 3.19-rc5 into usb-next

We want the usb fixes in this branch as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

.mailmap

@@ -51,6 +51,7 @@ Greg Kroah-Hartman <gregkh@suse.de>
 Greg Kroah-Hartman <greg@kroah.com>
 Henk Vergonet <Henk.Vergonet@gmail.com>
 Henrik Kretzschmar <henne@nachtwindheim.de>
+Henrik Rydberg <rydberg@bitmath.org>
 Herbert Xu <herbert@gondor.apana.org.au>
 Jacob Shin <Jacob.Shin@amd.com>
 James Bottomley <jejb@mulgrave.(none)>

Documentation/ABI/testing/sysfs-class-mei

@@ -14,3 +14,18 @@ Description:
 		The /sys/class/mei/meiN directory is created for
 		each probed mei device
 
+What:		/sys/class/mei/meiN/fw_status
+Date:		Nov 2014
+KernelVersion:	3.19
+Contact:	Tomas Winkler <tomas.winkler@intel.com>
+Description:	Display fw status registers content
+
+		The ME FW writes its status information into fw status
+		registers for BIOS and OS to monitor fw health.
+
+		The register contains running state, power management
+		state, error codes, and others. The way the registers
+		are decoded depends on PCH or SoC generation.
+		Also number of registers varies between 1 and 6
+		depending on generation.
+

Documentation/devicetree/bindings/input/gpio-keys.txt

@@ -10,12 +10,13 @@ Optional properties:
 Each button (key) is represented as a sub-node of "gpio-keys":
 Subnode properties:
 
+	- gpios: OF device-tree gpio specification.
+	- interrupts: the interrupt line for that input.
 	- label: Descriptive name of the key.
 	- linux,code: Keycode to emit.
 
-Required mutual exclusive subnode-properties:
-	- gpios: OF device-tree gpio specification.
-	- interrupts: the interrupt line for that input
+Note that either "interrupts" or "gpios" properties can be omitted, but not
+both at the same time. Specifying both properties is allowed.
 
 Optional subnode-properties:
 	- linux,input-type: Specify event type this button/key generates.
@@ -23,6 +24,9 @@ Optional subnode-properties:
 	- debounce-interval: Debouncing interval time in milliseconds.
 	  If not specified defaults to 5.
 	- gpio-key,wakeup: Boolean, button can wake-up the system.
+	- linux,can-disable: Boolean, indicates that button is connected
+	  to dedicated (not shared) interrupt which can be disabled to
+	  suppress events from the button.
 
 Example nodes:
 

Documentation/devicetree/bindings/input/stmpe-keypad.txt

@@ -8,6 +8,8 @@ Optional properties:
  - debounce-interval        : Debouncing interval time in milliseconds
  - st,scan-count            : Scanning cycles elapsed before key data is updated
  - st,no-autorepeat         : If specified device will not autorepeat
+ - keypad,num-rows          : See ./matrix-keymap.txt
+ - keypad,num-columns       : See ./matrix-keymap.txt
 
 Example:
 

Documentation/networking/ip-sysctl.txt

@@ -66,6 +66,8 @@ fwmark_reflect - BOOLEAN
 route/max_size - INTEGER
 	Maximum number of routes allowed in the kernel.  Increase
 	this when using large numbers of interfaces and/or routes.
+	From linux kernel 3.6 onwards, this is deprecated for ipv4
+	as route cache is no longer used.
 
 neigh/default/gc_thresh1 - INTEGER
 	Minimum number of entries to keep.  Garbage collector will not

Documentation/target/tcm_mod_builder.py

@@ -389,9 +389,6 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 	buf += "	.release_cmd			= " + fabric_mod_name + "_release_cmd,\n"
 	buf += "	.shutdown_session		= " + fabric_mod_name + "_shutdown_session,\n"
 	buf += "	.close_session			= " + fabric_mod_name + "_close_session,\n"
-	buf += "	.stop_session			= " + fabric_mod_name + "_stop_session,\n"
-	buf += "	.fall_back_to_erl0		= " + fabric_mod_name + "_reset_nexus,\n"
-	buf += "	.sess_logged_in			= " + fabric_mod_name + "_sess_logged_in,\n"
 	buf += "	.sess_get_index			= " + fabric_mod_name + "_sess_get_index,\n"
 	buf += "	.sess_get_initiator_sid		= NULL,\n"
 	buf += "	.write_pending			= " + fabric_mod_name + "_write_pending,\n"
@@ -402,7 +399,7 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 	buf += "	.queue_data_in			= " + fabric_mod_name + "_queue_data_in,\n"
 	buf += "	.queue_status			= " + fabric_mod_name + "_queue_status,\n"
 	buf += "	.queue_tm_rsp			= " + fabric_mod_name + "_queue_tm_rsp,\n"
-	buf += "	.is_state_remove		= " + fabric_mod_name + "_is_state_remove,\n"
+	buf += "	.aborted_task			= " + fabric_mod_name + "_aborted_task,\n"
 	buf += "	/*\n"
 	buf += "	 * Setup function pointers for generic logic in target_core_fabric_configfs.c\n"
 	buf += "	 */\n"
@@ -428,7 +425,7 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 	buf += "	/*\n"
 	buf += "	 * Register the top level struct config_item_type with TCM core\n"
 	buf += "	 */\n"
-	buf += "	fabric = target_fabric_configfs_init(THIS_MODULE, \"" + fabric_mod_name[4:] + "\");\n"
+	buf += "	fabric = target_fabric_configfs_init(THIS_MODULE, \"" + fabric_mod_name + "\");\n"
 	buf += "	if (IS_ERR(fabric)) {\n"
 	buf += "		printk(KERN_ERR \"target_fabric_configfs_init() failed\\n\");\n"
 	buf += "		return PTR_ERR(fabric);\n"
@@ -595,7 +592,7 @@ def tcm_mod_dump_fabric_ops(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 		if re.search('get_fabric_name', fo):
 			buf += "char *" + fabric_mod_name + "_get_fabric_name(void)\n"
 			buf += "{\n"
-			buf += "	return \"" + fabric_mod_name[4:] + "\";\n"
+			buf += "	return \"" + fabric_mod_name + "\";\n"
 			buf += "}\n\n"
 			bufi += "char *" + fabric_mod_name + "_get_fabric_name(void);\n"
 			continue
@@ -820,27 +817,6 @@ def tcm_mod_dump_fabric_ops(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 			buf += "}\n\n"
 			bufi += "void " + fabric_mod_name + "_close_session(struct se_session *);\n"
 
-		if re.search('stop_session\)\(', fo):
-			buf += "void " + fabric_mod_name + "_stop_session(struct se_session *se_sess, int sess_sleep , int conn_sleep)\n"
-			buf += "{\n"
-			buf += "	return;\n"
-			buf += "}\n\n"
-			bufi += "void " + fabric_mod_name + "_stop_session(struct se_session *, int, int);\n"
-
-		if re.search('fall_back_to_erl0\)\(', fo):
-			buf += "void " + fabric_mod_name + "_reset_nexus(struct se_session *se_sess)\n"
-			buf += "{\n"
-			buf += "	return;\n"
-			buf += "}\n\n"
-			bufi += "void " + fabric_mod_name + "_reset_nexus(struct se_session *);\n"
-
-		if re.search('sess_logged_in\)\(', fo):
-			buf += "int " + fabric_mod_name + "_sess_logged_in(struct se_session *se_sess)\n"
-			buf += "{\n"
-			buf += "	return 0;\n"
-			buf += "}\n\n"
-			bufi += "int " + fabric_mod_name + "_sess_logged_in(struct se_session *);\n"
-
 		if re.search('sess_get_index\)\(', fo):
 			buf += "u32 " + fabric_mod_name + "_sess_get_index(struct se_session *se_sess)\n"
 			buf += "{\n"
@@ -898,19 +874,18 @@ def tcm_mod_dump_fabric_ops(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 			bufi += "int " + fabric_mod_name + "_queue_status(struct se_cmd *);\n"
 
 		if re.search('queue_tm_rsp\)\(', fo):
-			buf += "int " + fabric_mod_name + "_queue_tm_rsp(struct se_cmd *se_cmd)\n"
+			buf += "void " + fabric_mod_name + "_queue_tm_rsp(struct se_cmd *se_cmd)\n"
 			buf += "{\n"
-			buf += "	return 0;\n"
+			buf += "	return;\n"
 			buf += "}\n\n"
-			bufi += "int " + fabric_mod_name + "_queue_tm_rsp(struct se_cmd *);\n"
+			bufi += "void " + fabric_mod_name + "_queue_tm_rsp(struct se_cmd *);\n"
 
-		if re.search('is_state_remove\)\(', fo):
-			buf += "int " + fabric_mod_name + "_is_state_remove(struct se_cmd *se_cmd)\n"
+		if re.search('aborted_task\)\(', fo):
+			buf += "void " + fabric_mod_name + "_aborted_task(struct se_cmd *se_cmd)\n"
 			buf += "{\n"
-			buf += "	return 0;\n"
+			buf += "	return;\n"
 			buf += "}\n\n"
-			bufi += "int " + fabric_mod_name + "_is_state_remove(struct se_cmd *);\n"
-
+			bufi += "void " + fabric_mod_name + "_aborted_task(struct se_cmd *);\n"
 
 	ret = p.write(buf)
 	if ret:
@@ -1018,11 +993,11 @@ def main(modname, proto_ident):
 	tcm_mod_build_kbuild(fabric_mod_dir, fabric_mod_name)
 	tcm_mod_build_kconfig(fabric_mod_dir, fabric_mod_name)
 
-	input = raw_input("Would you like to add " + fabric_mod_name + "to drivers/target/Makefile..? [yes,no]: ")
+	input = raw_input("Would you like to add " + fabric_mod_name + " to drivers/target/Makefile..? [yes,no]: ")
 	if input == "yes" or input == "y":
 		tcm_mod_add_kbuild(tcm_dir, fabric_mod_name)
 
-	input = raw_input("Would you like to add " + fabric_mod_name + "to drivers/target/Kconfig..? [yes,no]: ")
+	input = raw_input("Would you like to add " + fabric_mod_name + " to drivers/target/Kconfig..? [yes,no]: ")
 	if input == "yes" or input == "y":
 		tcm_mod_add_kconfig(tcm_dir, fabric_mod_name)
 

Documentation/thermal/cpu-cooling-api.txt

@@ -3,7 +3,7 @@ CPU cooling APIs How To
 
 Written by Amit Daniel Kachhap <amit.kachhap@linaro.org>
 
-Updated: 12 May 2012
+Updated: 6 Jan 2015
 
 Copyright (c)  2012 Samsung Electronics Co., Ltd(http://www.samsung.com)
 
@@ -25,7 +25,18 @@ the user. The registration APIs returns the cooling device pointer.
 
    clip_cpus: cpumask of cpus where the frequency constraints will happen.
 
-1.1.2 void cpufreq_cooling_unregister(struct thermal_cooling_device *cdev)
+1.1.2 struct thermal_cooling_device *of_cpufreq_cooling_register(
+	struct device_node *np, const struct cpumask *clip_cpus)
+
+    This interface function registers the cpufreq cooling device with
+    the name "thermal-cpufreq-%x" linking it with a device tree node, in
+    order to bind it via the thermal DT code. This api can support multiple
+    instances of cpufreq cooling devices.
+
+    np: pointer to the cooling device device tree node
+    clip_cpus: cpumask of cpus where the frequency constraints will happen.
+
+1.1.3 void cpufreq_cooling_unregister(struct thermal_cooling_device *cdev)
 
     This interface function unregisters the "thermal-cpufreq-%x" cooling device.
 

MAINTAINERS

@@ -724,15 +724,15 @@ F:	include/uapi/linux/apm_bios.h
 F:	drivers/char/apm-emulation.c
 
 APPLE BCM5974 MULTITOUCH DRIVER
-M:	Henrik Rydberg <rydberg@euromail.se>
+M:	Henrik Rydberg <rydberg@bitmath.org>
 L:	linux-input@vger.kernel.org
-S:	Maintained
+S:	Odd fixes
 F:	drivers/input/mouse/bcm5974.c
 
 APPLE SMC DRIVER
-M:	Henrik Rydberg <rydberg@euromail.se>
+M:	Henrik Rydberg <rydberg@bitmath.org>
 L:	lm-sensors@lm-sensors.org
-S:	Maintained
+S:	Odd fixes
 F:	drivers/hwmon/applesmc.c
 
 APPLETALK NETWORK LAYER
@@ -2259,6 +2259,7 @@ F:	drivers/gpio/gpio-bt8xx.c
 BTRFS FILE SYSTEM
 M:	Chris Mason <clm@fb.com>
 M:	Josef Bacik <jbacik@fb.com>
+M:	David Sterba <dsterba@suse.cz>
 L:	linux-btrfs@vger.kernel.org
 W:	http://btrfs.wiki.kernel.org/
 Q:	http://patchwork.kernel.org/project/linux-btrfs/list/
@@ -3182,7 +3183,7 @@ L:	dmaengine@vger.kernel.org
 Q:	https://patchwork.kernel.org/project/linux-dmaengine/list/
 S:	Maintained
 F:	drivers/dma/
-F:	include/linux/dma*
+F:	include/linux/dmaengine.h
 F:	Documentation/dmaengine/
 T:	git git://git.infradead.org/users/vkoul/slave-dma.git
 
@@ -4748,7 +4749,7 @@ S:	Supported
 F:	drivers/scsi/ipr.*
 
 IBM Power Virtual Ethernet Device Driver
-M:	Santiago Leon <santil@linux.vnet.ibm.com>
+M:	Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/ethernet/ibm/ibmveth.*
@@ -4940,10 +4941,10 @@ F:	include/uapi/linux/input.h
 F:	include/linux/input/
 
 INPUT MULTITOUCH (MT) PROTOCOL
-M:	Henrik Rydberg <rydberg@euromail.se>
+M:	Henrik Rydberg <rydberg@bitmath.org>
 L:	linux-input@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/rydberg/input-mt.git
-S:	Maintained
+S:	Odd fixes
 F:	Documentation/input/multi-touch-protocol.txt
 F:	drivers/input/input-mt.c
 K:	\b(ABS|SYN)_MT_
@@ -5279,6 +5280,15 @@ W:	www.open-iscsi.org
 Q:	http://patchwork.kernel.org/project/linux-rdma/list/
 F:	drivers/infiniband/ulp/iser/
 
+ISCSI EXTENSIONS FOR RDMA (ISER) TARGET
+M:	Sagi Grimberg <sagig@mellanox.com>
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending.git master
+L:	linux-rdma@vger.kernel.org
+L:	target-devel@vger.kernel.org
+S:	Supported
+W:	http://www.linux-iscsi.org
+F:	drivers/infiniband/ulp/isert
+
 ISDN SUBSYSTEM
 M:	Karsten Keil <isdn@linux-pingi.de>
 L:	isdn4linux@listserv.isdn4linux.de (subscribers-only)
@@ -7737,8 +7747,7 @@ F:	Documentation/scsi/LICENSE.qla2xxx
 F:	drivers/scsi/qla2xxx/
 
 QLOGIC QLA4XXX iSCSI DRIVER
-M:	Vikas Chaudhary <vikas.chaudhary@qlogic.com>
-M:	iscsi-driver@qlogic.com
+M:	QLogic-Storage-Upstream@qlogic.com
 L:	linux-scsi@vger.kernel.org
 S:	Supported
 F:	Documentation/scsi/LICENSE.qla4xxx
@@ -9533,7 +9542,8 @@ F:	drivers/platform/x86/thinkpad_acpi.c
 TI BANDGAP AND THERMAL DRIVER
 M:	Eduardo Valentin <edubezval@gmail.com>
 L:	linux-pm@vger.kernel.org
-S:	Supported
+L:	linux-omap@vger.kernel.org
+S:	Maintained
 F:	drivers/thermal/ti-soc-thermal/
 
 TI CLOCK DRIVER

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 19
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc5
 NAME = Diseased Newt
 
 # *DOCUMENTATION*
@@ -391,6 +391,7 @@ USERINCLUDE    := \
 # Needed to be compatible with the O= option
 LINUXINCLUDE    := \
 		-I$(srctree)/arch/$(hdr-arch)/include \
+		-Iarch/$(hdr-arch)/include/generated/uapi \
 		-Iarch/$(hdr-arch)/include/generated \
 		$(if $(KBUILD_SRC), -I$(srctree)/include) \
 		-Iinclude \

arch/arm/boot/dts/armada-370-db.dts

@@ -203,27 +203,3 @@
 		compatible = "linux,spdif-dir";
 	};
 };
-
-&pinctrl {
-	/*
-	 * These pins might be muxed as I2S by
-	 * the bootloader, but it conflicts
-	 * with the real I2S pins that are
-	 * muxed using i2s_pins. We must mux
-	 * those pins to a function other than
-	 * I2S.
-	 */
-	pinctrl-0 = <&hog_pins1 &hog_pins2>;
-	pinctrl-names = "default";
-
-	hog_pins1: hog-pins1 {
-		marvell,pins = "mpp6",  "mpp8", "mpp10",
-			       "mpp12", "mpp13";
-		marvell,function = "gpio";
-	};
-
-	hog_pins2: hog-pins2 {
-		marvell,pins = "mpp5", "mpp7", "mpp9";
-		marvell,function = "gpo";
-	};
-};

arch/arm/boot/dts/at91sam9263.dtsi

@@ -953,6 +953,8 @@
 			interrupts = <26 IRQ_TYPE_LEVEL_HIGH 3>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_fb>;
+			clocks = <&lcd_clk>, <&lcd_clk>;
+			clock-names = "lcdc_clk", "hclk";
 			status = "disabled";
 		};
 

arch/arm/boot/dts/berlin2q-marvell-dmp.dts

@@ -65,6 +65,8 @@
 };
 
 &sdhci2 {
+	broken-cd;
+	bus-width = <8>;
 	non-removable;
 	status = "okay";
 };

arch/arm/boot/dts/berlin2q.dtsi

@@ -83,7 +83,8 @@
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab1000 0x200>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&chip CLKID_SDIO1XIN>;
+			clocks = <&chip CLKID_NFC_ECC>, <&chip CLKID_NFC>;
+			clock-names = "io", "core";
 			status = "disabled";
 		};
 
@@ -348,36 +349,6 @@
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 			};
-
-			gpio4: gpio@5000 {
-				compatible = "snps,dw-apb-gpio";
-				reg = <0x5000 0x400>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				porte: gpio-port@4 {
-					compatible = "snps,dw-apb-gpio-port";
-					gpio-controller;
-					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
-					reg = <0>;
-				};
-			};
-
-			gpio5: gpio@c000 {
-				compatible = "snps,dw-apb-gpio";
-				reg = <0xc000 0x400>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				portf: gpio-port@5 {
-					compatible = "snps,dw-apb-gpio-port";
-					gpio-controller;
-					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
-					reg = <0>;
-				};
-			};
 		};
 
 		chip: chip-control@ea0000 {
@@ -466,6 +437,21 @@
 			ranges = <0 0xfc0000 0x10000>;
 			interrupt-parent = <&sic>;
 
+			sm_gpio1: gpio@5000 {
+				compatible = "snps,dw-apb-gpio";
+				reg = <0x5000 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				portf: gpio-port@5 {
+					compatible = "snps,dw-apb-gpio-port";
+					gpio-controller;
+					#gpio-cells = <2>;
+					snps,nr-gpios = <32>;
+					reg = <0>;
+				};
+			};
+
 			i2c2: i2c@7000 {
 				compatible = "snps,designware-i2c";
 				#address-cells = <1>;
@@ -516,6 +502,21 @@
 				status = "disabled";
 			};
 
+			sm_gpio0: gpio@c000 {
+				compatible = "snps,dw-apb-gpio";
+				reg = <0xc000 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				porte: gpio-port@4 {
+					compatible = "snps,dw-apb-gpio-port";
+					gpio-controller;
+					#gpio-cells = <2>;
+					snps,nr-gpios = <32>;
+					reg = <0>;
+				};
+			};
+
 			sysctrl: pin-controller@d000 {
 				compatible = "marvell,berlin2q-system-ctrl";
 				reg = <0xd000 0x100>;

arch/arm/boot/dts/dra7-evm.dts

@@ -499,23 +499,23 @@
 		};
 		partition@5 {
 			label = "QSPI.u-boot-spl-os";
-			reg = <0x00140000 0x00010000>;
+			reg = <0x00140000 0x00080000>;
 		};
 		partition@6 {
 			label = "QSPI.u-boot-env";
-			reg = <0x00150000 0x00010000>;
+			reg = <0x001c0000 0x00010000>;
 		};
 		partition@7 {
 			label = "QSPI.u-boot-env.backup1";
-			reg = <0x00160000 0x0010000>;
+			reg = <0x001d0000 0x0010000>;
 		};
 		partition@8 {
 			label = "QSPI.kernel";
-			reg = <0x00170000 0x0800000>;
+			reg = <0x001e0000 0x0800000>;
 		};
 		partition@9 {
 			label = "QSPI.file-system";
-			reg = <0x00970000 0x01690000>;
+			reg = <0x009e0000 0x01620000>;
 		};
 	};
 };

arch/arm/boot/dts/exynos5250.dtsi

@@ -736,7 +736,7 @@
 
 	dp_phy: video-phy@10040720 {
 		compatible = "samsung,exynos5250-dp-video-phy";
-		reg = <0x10040720 4>;
+		samsung,pmu-syscon = <&pmu_system_controller>;
 		#phy-cells = <0>;
 	};
 

arch/arm/boot/dts/exynos5420-arndale-octa.dts

@@ -372,3 +372,7 @@
 &usbdrd_dwc3_1 {
 	dr_mode = "host";
 };
+
+&cci {
+	status = "disabled";
+};

arch/arm/boot/dts/exynos5420.dtsi

@@ -120,7 +120,7 @@
 		};
 	};
 
-	cci@10d20000 {
+	cci: cci@10d20000 {
 		compatible = "arm,cci-400";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -503,8 +503,8 @@
 	};
 
 	dp_phy: video-phy@10040728 {
-		compatible = "samsung,exynos5250-dp-video-phy";
-		reg = <0x10040728 4>;
+		compatible = "samsung,exynos5420-dp-video-phy";
+		samsung,pmu-syscon = <&pmu_system_controller>;
 		#phy-cells = <0>;
 	};
 

arch/arm/boot/dts/imx25.dtsi

@@ -162,7 +162,7 @@
 				#size-cells = <0>;
 				compatible = "fsl,imx25-cspi", "fsl,imx35-cspi";
 				reg = <0x43fa4000 0x4000>;
-				clocks = <&clks 62>, <&clks 62>;
+				clocks = <&clks 78>, <&clks 78>;
 				clock-names = "ipg", "per";
 				interrupts = <14>;
 				status = "disabled";

arch/arm/boot/dts/imx51-babbage.dts

@@ -127,24 +127,12 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		reg_usbh1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1reg>;
-			reg = <0>;
-			regulator-name = "usbh1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio2 5 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		reg_usbotg_vbus: regulator@1 {
+		reg_hub_reset: regulator@0 {
 			compatible = "regulator-fixed";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usbotgreg>;
-			reg = <1>;
-			regulator-name = "usbotg_vbus";
+			reg = <0>;
+			regulator-name = "hub_reset";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
@@ -176,6 +164,7 @@
 			reg = <0>;
 			clocks = <&clks IMX5_CLK_DUMMY>;
 			clock-names = "main_clk";
+			reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -419,7 +408,7 @@
 &usbh1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh1>;
-	vbus-supply = <&reg_usbh1_vbus>;
+	vbus-supply = <&reg_hub_reset>;
 	fsl,usbphy = <&usbh1phy>;
 	phy_type = "ulpi";
 	status = "okay";
@@ -429,7 +418,6 @@
 	dr_mode = "otg";
 	disable-over-current;
 	phy_type = "utmi_wide";
-	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx6qdl.dtsi

@@ -335,8 +335,8 @@
 			vpu: vpu@02040000 {
 				compatible = "cnm,coda960";
 				reg = <0x02040000 0x3c000>;
-				interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>,
-				             <0 12 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>,
+					     <0 3 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "bit", "jpeg";
 				clocks = <&clks IMX6QDL_CLK_VPU_AXI>,
 					 <&clks IMX6QDL_CLK_MMDC_CH0_AXI>,

arch/arm/boot/dts/imx6sx-sdb.dts

@@ -159,13 +159,28 @@
 	pinctrl-0 = <&pinctrl_enet1>;
 	phy-supply = <&reg_enet_3v3>;
 	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@0 {
+			reg = <0>;
+		};
+
+		ethphy2: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
 };
 
 &fec2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet2>;
 	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
 	status = "okay";
 };
 

arch/arm/boot/dts/ls1021a.dtsi

@@ -142,6 +142,7 @@
 		scfg: scfg@1570000 {
 			compatible = "fsl,ls1021a-scfg", "syscon";
 			reg = <0x0 0x1570000 0x0 0x10000>;
+			big-endian;
 		};
 
 		clockgen: clocking@1ee1000 {

arch/arm/boot/dts/omap3-n900.dts

@@ -700,11 +700,9 @@
 		};
 	};
 
+	/* Ethernet is on some early development boards and qemu */
 	ethernet@gpmc {
 		compatible = "smsc,lan91c94";
-
-		status = "disabled";
-
 		interrupt-parent = <&gpio2>;
 		interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;	/* gpio54 */
 		reg = <1 0x300 0xf>;		/* 16 byte IO range at offset 0x300 */

arch/arm/boot/dts/rk3288-evb.dtsi

@@ -155,6 +155,15 @@
 };
 
 &pinctrl {
+	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+		drive-strength = <8>;
+	};
+
+	pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
 	backlight {
 		bl_en: bl-en {
 			rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
@@ -173,6 +182,27 @@
 		};
 	};
 
+	sdmmc {
+		/*
+		 * Default drive strength isn't enough to achieve even
+		 * high-speed mode on EVB board so bump up to 8ma.
+		 */
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+	};
+
 	usb {
 		host_vbus_drv: host-vbus-drv {
 			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;

arch/arm/boot/dts/sama5d3xmb.dtsi

@@ -176,7 +176,7 @@
 			"Headphone Jack", "HPOUTR",
 			"IN2L", "Line In Jack",
 			"IN2R", "Line In Jack",
-			"MICBIAS", "IN1L",
+			"Mic", "MICBIAS",
 			"IN1L", "Mic";
 
 		atmel,ssc-controller = <&ssc0>;

arch/arm/boot/dts/sama5d4.dtsi

@@ -1008,7 +1008,7 @@
 
 			pit: timer@fc068630 {
 				compatible = "atmel,at91sam9260-pit";
-				reg = <0xfc068630 0xf>;
+				reg = <0xfc068630 0x10>;
 				interrupts = <3 IRQ_TYPE_LEVEL_HIGH 5>;
 				clocks = <&h32ck>;
 			};

arch/arm/boot/dts/ste-nomadik-nhk15.dts

@@ -25,11 +25,11 @@
 		stmpe2401_1 {
 			stmpe2401_1_nhk_mode: stmpe2401_1_nhk {
 				nhk_cfg1 {
-					ste,pins = "GPIO76_B20"; // IRQ line
+					pins = "GPIO76_B20"; // IRQ line
 					ste,input = <0>;
 				};
 				nhk_cfg2 {
-					ste,pins = "GPIO77_B8"; // reset line
+					pins = "GPIO77_B8"; // reset line
 					ste,output = <1>;
 				};
 			};
@@ -37,11 +37,11 @@
 		stmpe2401_2 {
 			stmpe2401_2_nhk_mode: stmpe2401_2_nhk {
 				nhk_cfg1 {
-					ste,pins = "GPIO78_A8"; // IRQ line
+					pins = "GPIO78_A8"; // IRQ line
 					ste,input = <0>;
 				};
 				nhk_cfg2 {
-					ste,pins = "GPIO79_C9"; // reset line
+					pins = "GPIO79_C9"; // reset line
 					ste,output = <1>;
 				};
 			};

arch/arm/boot/dts/vf610-twr.dts

@@ -129,13 +129,28 @@
 
 &fec0 {
 	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec0>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
 };
 
 &fec1 {
 	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec1>;
 	status = "okay";

arch/arm/configs/exynos_defconfig

@@ -84,7 +84,8 @@ CONFIG_DEBUG_GPIO=y
 CONFIG_POWER_SUPPLY=y
 CONFIG_BATTERY_SBS=y
 CONFIG_CHARGER_TPS65090=y
-# CONFIG_HWMON is not set
+CONFIG_HWMON=y
+CONFIG_SENSORS_LM90=y
 CONFIG_THERMAL=y
 CONFIG_EXYNOS_THERMAL=y
 CONFIG_EXYNOS_THERMAL_CORE=y
@@ -109,11 +110,26 @@ CONFIG_REGULATOR_S2MPA01=y
 CONFIG_REGULATOR_S2MPS11=y
 CONFIG_REGULATOR_S5M8767=y
 CONFIG_REGULATOR_TPS65090=y
+CONFIG_DRM=y
+CONFIG_DRM_BRIDGE=y
+CONFIG_DRM_PTN3460=y
+CONFIG_DRM_PS8622=y
+CONFIG_DRM_EXYNOS=y
+CONFIG_DRM_EXYNOS_FIMD=y
+CONFIG_DRM_EXYNOS_DP=y
+CONFIG_DRM_PANEL=y
+CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_FB=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_FB_SIMPLE=y
 CONFIG_EXYNOS_VIDEO=y
 CONFIG_EXYNOS_MIPI_DSI=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+CONFIG_LCD_PLATFORM=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_GENERIC=y
+CONFIG_BACKLIGHT_PWM=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FONTS=y
 CONFIG_FONT_7x14=y

arch/arm/configs/multi_v7_defconfig

@@ -338,6 +338,7 @@ CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_MVEBU=y
 CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_EXYNOS=y
 CONFIG_USB_EHCI_TEGRA=y
 CONFIG_USB_EHCI_HCD_STI=y
 CONFIG_USB_EHCI_HCD_PLATFORM=y

arch/arm/configs/omap2plus_defconfig

@@ -68,7 +68,7 @@ CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
 CONFIG_CPU_FREQ_GOV_POWERSAVE=y
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
-CONFIG_GENERIC_CPUFREQ_CPU0=y
+CONFIG_CPUFREQ_DT=y
 # CONFIG_ARM_OMAP2PLUS_CPUFREQ is not set
 CONFIG_CPU_IDLE=y
 CONFIG_BINFMT_MISC=y

arch/arm/include/uapi/asm/unistd.h

@@ -413,6 +413,7 @@
 #define __NR_getrandom			(__NR_SYSCALL_BASE+384)
 #define __NR_memfd_create		(__NR_SYSCALL_BASE+385)
 #define __NR_bpf			(__NR_SYSCALL_BASE+386)
+#define __NR_execveat			(__NR_SYSCALL_BASE+387)
 
 /*
  * The following SWIs are ARM private.

arch/arm/kernel/calls.S

@@ -396,6 +396,7 @@
 		CALL(sys_getrandom)
 /* 385 */	CALL(sys_memfd_create)
 		CALL(sys_bpf)
+		CALL(sys_execveat)
 #ifndef syscalls_counted
 .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
 #define syscalls_counted

arch/arm/kernel/perf_regs.c

@@ -28,3 +28,11 @@ u64 perf_reg_abi(struct task_struct *task)
 {
 	return PERF_SAMPLE_REGS_ABI_32;
 }
+
+void perf_get_regs_user(struct perf_regs *regs_user,
+			struct pt_regs *regs,
+			struct pt_regs *regs_user_copy)
+{
+	regs_user->regs = task_pt_regs(current);
+	regs_user->abi = perf_reg_abi(current);
+}

arch/arm/kernel/setup.c

@@ -1046,6 +1046,15 @@ static int c_show(struct seq_file *m, void *v)
 		seq_printf(m, "model name\t: %s rev %d (%s)\n",
 			   cpu_name, cpuid & 15, elf_platform);
 
+#if defined(CONFIG_SMP)
+		seq_printf(m, "BogoMIPS\t: %lu.%02lu\n",
+			   per_cpu(cpu_data, i).loops_per_jiffy / (500000UL/HZ),
+			   (per_cpu(cpu_data, i).loops_per_jiffy / (5000UL/HZ)) % 100);
+#else
+		seq_printf(m, "BogoMIPS\t: %lu.%02lu\n",
+			   loops_per_jiffy / (500000/HZ),
+			   (loops_per_jiffy / (5000/HZ)) % 100);
+#endif
 		/* dump out the processor features */
 		seq_puts(m, "Features\t: ");
 

arch/arm/kernel/smp.c

@@ -387,6 +387,18 @@ asmlinkage void secondary_start_kernel(void)
 
 void __init smp_cpus_done(unsigned int max_cpus)
 {
+	int cpu;
+	unsigned long bogosum = 0;
+
+	for_each_online_cpu(cpu)
+		bogosum += per_cpu(cpu_data, cpu).loops_per_jiffy;
+
+	printk(KERN_INFO "SMP: Total of %d processors activated "
+	       "(%lu.%02lu BogoMIPS).\n",
+	       num_online_cpus(),
+	       bogosum / (500000/HZ),
+	       (bogosum / (5000/HZ)) % 100);
+
 	hyp_mode_check();
 }
 

arch/arm/mach-at91/board-dt-sama5.c

@@ -17,6 +17,7 @@
 #include <linux/of_platform.h>
 #include <linux/phy.h>
 #include <linux/clk-provider.h>
+#include <linux/phy.h>
 
 #include <asm/setup.h>
 #include <asm/irq.h>
@@ -26,8 +27,25 @@
 
 #include "generic.h"
 
+static int ksz8081_phy_fixup(struct phy_device *phy)
+{
+	int value;
+
+	value = phy_read(phy, 0x16);
+	value &= ~0x20;
+	phy_write(phy, 0x16, value);
+
+	return 0;
+}
+
 static void __init sama5_dt_device_init(void)
 {
+	if (of_machine_is_compatible("atmel,sama5d4ek") &&
+	   IS_ENABLED(CONFIG_PHYLIB)) {
+		phy_register_fixup_for_id("fc028000.etherne:00",
+						ksz8081_phy_fixup);
+	}
+
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 

arch/arm/mach-imx/clk-imx6q.c

@@ -144,7 +144,7 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 		post_div_table[1].div = 1;
 		post_div_table[2].div = 1;
 		video_div_table[1].div = 1;
-		video_div_table[2].div = 1;
+		video_div_table[3].div = 1;
 	}
 
 	clk[IMX6QDL_PLL1_BYPASS_SRC] = imx_clk_mux("pll1_bypass_src", base + 0x00, 14, 2, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels));

arch/arm/mach-imx/clk-imx6sx.c

@@ -558,6 +558,9 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node)
 	clk_set_parent(clks[IMX6SX_CLK_GPU_CORE_SEL], clks[IMX6SX_CLK_PLL3_PFD0]);
 	clk_set_parent(clks[IMX6SX_CLK_GPU_AXI_SEL], clks[IMX6SX_CLK_PLL3_PFD0]);
 
+	clk_set_parent(clks[IMX6SX_CLK_QSPI1_SEL], clks[IMX6SX_CLK_PLL2_BUS]);
+	clk_set_parent(clks[IMX6SX_CLK_QSPI2_SEL], clks[IMX6SX_CLK_PLL2_BUS]);
+
 	/* Set initial power mode */
 	imx6q_set_lpm(WAIT_CLOCKED);
 }

arch/arm/mach-omap2/board-generic.c

@@ -77,6 +77,24 @@ MACHINE_END
 #endif
 
 #ifdef CONFIG_ARCH_OMAP3
+/* Some boards need board name for legacy userspace in /proc/cpuinfo */
+static const char *const n900_boards_compat[] __initconst = {
+	"nokia,omap3-n900",
+	NULL,
+};
+
+DT_MACHINE_START(OMAP3_N900_DT, "Nokia RX-51 board")
+	.reserve	= omap_reserve,
+	.map_io		= omap3_map_io,
+	.init_early	= omap3430_init_early,
+	.init_machine	= omap_generic_init,
+	.init_late	= omap3_init_late,
+	.init_time	= omap3_sync32k_timer_init,
+	.dt_compat	= n900_boards_compat,
+	.restart	= omap3xxx_restart,
+MACHINE_END
+
+/* Generic omap3 boards, most boards can use these */
 static const char *const omap3_boards_compat[] __initconst = {
 	"ti,omap3430",
 	"ti,omap3",

arch/arm/mach-omap2/common.h

@@ -249,6 +249,7 @@ extern void omap4_cpu_die(unsigned int cpu);
 extern struct smp_operations omap4_smp_ops;
 
 extern void omap5_secondary_startup(void);
+extern void omap5_secondary_hyp_startup(void);
 #endif
 
 #if defined(CONFIG_SMP) && defined(CONFIG_PM)

arch/arm/mach-omap2/control.h

@@ -286,6 +286,10 @@
 #define OMAP5XXX_CONTROL_STATUS                0x134
 #define OMAP5_DEVICETYPE_MASK          (0x7 << 6)
 
+/* DRA7XX CONTROL CORE BOOTSTRAP */
+#define DRA7_CTRL_CORE_BOOTSTRAP	0x6c4
+#define DRA7_SPEEDSELECT_MASK		(0x3 << 8)
+
 /*
  * REVISIT: This list of registers is not comprehensive - there are more
  * that should be added.

arch/arm/mach-omap2/omap-headsmp.S

@@ -22,6 +22,7 @@
 
 /* Physical address needed since MMU not enabled yet on secondary core */
 #define AUX_CORE_BOOT0_PA			0x48281800
+#define API_HYP_ENTRY				0x102
 
 /*
  * OMAP5 specific entry point for secondary CPU to jump from ROM
@@ -40,6 +41,26 @@ wait:	ldr	r2, =AUX_CORE_BOOT0_PA	@ read from AuxCoreBoot0
 	bne	wait
 	b	secondary_startup
 ENDPROC(omap5_secondary_startup)
+/*
+ * Same as omap5_secondary_startup except we call into the ROM to
+ * enable HYP mode first.  This is called instead of
+ * omap5_secondary_startup if the primary CPU was put into HYP mode by
+ * the boot loader.
+ */
+ENTRY(omap5_secondary_hyp_startup)
+wait_2:	ldr	r2, =AUX_CORE_BOOT0_PA	@ read from AuxCoreBoot0
+	ldr	r0, [r2]
+	mov	r0, r0, lsr #5
+	mrc	p15, 0, r4, c0, c0, 5
+	and	r4, r4, #0x0f
+	cmp	r0, r4
+	bne	wait_2
+	ldr	r12, =API_HYP_ENTRY
+	adr	r0, hyp_boot
+	smc	#0
+hyp_boot:
+	b	secondary_startup
+ENDPROC(omap5_secondary_hyp_startup)
 /*
  * OMAP4 specific entry point for secondary CPU to jump from ROM
  * code.  This routine also provides a holding flag into which

arch/arm/mach-omap2/omap-smp.c

@@ -22,6 +22,7 @@
 #include <linux/irqchip/arm-gic.h>
 
 #include <asm/smp_scu.h>
+#include <asm/virt.h>
 
 #include "omap-secure.h"
 #include "omap-wakeupgen.h"
@@ -227,8 +228,16 @@ static void __init omap4_smp_prepare_cpus(unsigned int max_cpus)
 	if (omap_secure_apis_support())
 		omap_auxcoreboot_addr(virt_to_phys(startup_addr));
 	else
-		writel_relaxed(virt_to_phys(omap5_secondary_startup),
-			       base + OMAP_AUX_CORE_BOOT_1);
+		/*
+		 * If the boot CPU is in HYP mode then start secondary
+		 * CPU in HYP mode as well.
+		 */
+		if ((__boot_cpu_mode & MODE_MASK) == HYP_MODE)
+			writel_relaxed(virt_to_phys(omap5_secondary_hyp_startup),
+				       base + OMAP_AUX_CORE_BOOT_1);
+		else
+			writel_relaxed(virt_to_phys(omap5_secondary_startup),
+				       base + OMAP_AUX_CORE_BOOT_1);
 
 }
 

arch/arm/mach-omap2/timer.c

@@ -54,6 +54,7 @@
 
 #include "soc.h"
 #include "common.h"
+#include "control.h"
 #include "powerdomain.h"
 #include "omap-secure.h"
 
@@ -496,7 +497,8 @@ static void __init realtime_counter_init(void)
 	void __iomem *base;
 	static struct clk *sys_clk;
 	unsigned long rate;
-	unsigned int reg, num, den;
+	unsigned int reg;
+	unsigned long long num, den;
 
 	base = ioremap(REALTIME_COUNTER_BASE, SZ_32);
 	if (!base) {
@@ -511,13 +513,42 @@ static void __init realtime_counter_init(void)
 	}
 
 	rate = clk_get_rate(sys_clk);
+
+	if (soc_is_dra7xx()) {
+		/*
+		 * Errata i856 says the 32.768KHz crystal does not start at
+		 * power on, so the CPU falls back to an emulated 32KHz clock
+		 * based on sysclk / 610 instead. This causes the master counter
+		 * frequency to not be 6.144MHz but at sysclk / 610 * 375 / 2
+		 * (OR sysclk * 75 / 244)
+		 *
+		 * This affects at least the DRA7/AM572x 1.0, 1.1 revisions.
+		 * Of course any board built without a populated 32.768KHz
+		 * crystal would also need this fix even if the CPU is fixed
+		 * later.
+		 *
+		 * Either case can be detected by using the two speedselect bits
+		 * If they are not 0, then the 32.768KHz clock driving the
+		 * coarse counter that corrects the fine counter every time it
+		 * ticks is actually rate/610 rather than 32.768KHz and we
+		 * should compensate to avoid the 570ppm (at 20MHz, much worse
+		 * at other rates) too fast system time.
+		 */
+		reg = omap_ctrl_readl(DRA7_CTRL_CORE_BOOTSTRAP);
+		if (reg & DRA7_SPEEDSELECT_MASK) {
+			num = 75;
+			den = 244;
+			goto sysclk1_based;
+		}
+	}
+
 	/* Numerator/denumerator values refer TRM Realtime Counter section */
 	switch (rate) {
-	case 1200000:
+	case 12000000:
 		num = 64;
 		den = 125;
 		break;
-	case 1300000:
+	case 13000000:
 		num = 768;
 		den = 1625;
 		break;
@@ -529,11 +560,11 @@ static void __init realtime_counter_init(void)
 		num = 192;
 		den = 625;
 		break;
-	case 2600000:
+	case 26000000:
 		num = 384;
 		den = 1625;
 		break;
-	case 2700000:
+	case 27000000:
 		num = 256;
 		den = 1125;
 		break;
@@ -545,6 +576,7 @@ static void __init realtime_counter_init(void)
 		break;
 	}
 
+sysclk1_based:
 	/* Program numerator and denumerator registers */
 	reg = readl_relaxed(base + INCREMENTER_NUMERATOR_OFFSET) &
 			NUMERATOR_DENUMERATOR_MASK;
@@ -556,7 +588,7 @@ static void __init realtime_counter_init(void)
 	reg |= den;
 	writel_relaxed(reg, base + INCREMENTER_DENUMERATOR_RELOAD_OFFSET);
 
-	arch_timer_freq = (rate / den) * num;
+	arch_timer_freq = DIV_ROUND_UP_ULL(rate * num, den);
 	set_cntfreq();
 
 	iounmap(base);

arch/arm/mach-rockchip/rockchip.c

@@ -19,11 +19,37 @@
 #include <linux/init.h>
 #include <linux/of_platform.h>
 #include <linux/irqchip.h>
+#include <linux/clk-provider.h>
+#include <linux/clocksource.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <asm/hardware/cache-l2x0.h>
 #include "core.h"
 
+#define RK3288_GRF_SOC_CON0 0x244
+
+static void __init rockchip_timer_init(void)
+{
+	if (of_machine_is_compatible("rockchip,rk3288")) {
+		struct regmap *grf;
+
+		/*
+		 * Disable auto jtag/sdmmc switching that causes issues
+		 * with the mmc controllers making them unreliable
+		 */
+		grf = syscon_regmap_lookup_by_compatible("rockchip,rk3288-grf");
+		if (!IS_ERR(grf))
+			regmap_write(grf, RK3288_GRF_SOC_CON0, 0x10000000);
+		else
+			pr_err("rockchip: could not get grf syscon\n");
+	}
+
+	of_clk_init(NULL);
+	clocksource_of_init();
+}
+
 static void __init rockchip_dt_init(void)
 {
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
@@ -42,6 +68,7 @@ static const char * const rockchip_board_dt_compat[] = {
 DT_MACHINE_START(ROCKCHIP_DT, "Rockchip Cortex-A9 (Device Tree)")
 	.l2c_aux_val	= 0,
 	.l2c_aux_mask	= ~0,
+	.init_time	= rockchip_timer_init,
 	.dt_compat	= rockchip_board_dt_compat,
 	.init_machine	= rockchip_dt_init,
 MACHINE_END

arch/arm/mach-shmobile/setup-r8a7740.c

@@ -800,7 +800,14 @@ void __init r8a7740_init_irq_of(void)
 	void __iomem *intc_msk_base = ioremap_nocache(0xe6900040, 0x10);
 	void __iomem *pfc_inta_ctrl = ioremap_nocache(0xe605807c, 0x4);
 
+#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
+	void __iomem *gic_dist_base = ioremap_nocache(0xc2800000, 0x1000);
+	void __iomem *gic_cpu_base = ioremap_nocache(0xc2000000, 0x1000);
+
+	gic_init(0, 29, gic_dist_base, gic_cpu_base);
+#else
 	irqchip_init();
+#endif
 
 	/* route signals to GIC */
 	iowrite32(0x0, pfc_inta_ctrl);

arch/arm/mach-shmobile/setup-sh73a0.c

@@ -595,6 +595,7 @@ static struct platform_device ipmmu_device = {
 
 static struct renesas_intc_irqpin_config irqpin0_platform_data = {
 	.irq_base = irq_pin(0), /* IRQ0 -> IRQ7 */
+	.control_parent = true,
 };
 
 static struct resource irqpin0_resources[] = {
@@ -656,6 +657,7 @@ static struct platform_device irqpin1_device = {
 
 static struct renesas_intc_irqpin_config irqpin2_platform_data = {
 	.irq_base = irq_pin(16), /* IRQ16 -> IRQ23 */
+	.control_parent = true,
 };
 
 static struct resource irqpin2_resources[] = {
@@ -686,6 +688,7 @@ static struct platform_device irqpin2_device = {
 
 static struct renesas_intc_irqpin_config irqpin3_platform_data = {
 	.irq_base = irq_pin(24), /* IRQ24 -> IRQ31 */
+	.control_parent = true,
 };
 
 static struct resource irqpin3_resources[] = {

arch/arm/mm/dump.c

@@ -220,9 +220,6 @@ static void note_page(struct pg_state *st, unsigned long addr, unsigned level, u
 	static const char units[] = "KMGTPE";
 	u64 prot = val & pg_level[level].mask;
 
-	if (addr < USER_PGTABLES_CEILING)
-		return;
-
 	if (!st->level) {
 		st->level = level;
 		st->current_prot = prot;
@@ -308,15 +305,13 @@ static void walk_pgd(struct seq_file *m)
 	pgd_t *pgd = swapper_pg_dir;
 	struct pg_state st;
 	unsigned long addr;
-	unsigned i, pgdoff = USER_PGTABLES_CEILING / PGDIR_SIZE;
+	unsigned i;
 
 	memset(&st, 0, sizeof(st));
 	st.seq = m;
 	st.marker = address_markers;
 
-	pgd += pgdoff;
-
-	for (i = pgdoff; i < PTRS_PER_PGD; i++, pgd++) {
+	for (i = 0; i < PTRS_PER_PGD; i++, pgd++) {
 		addr = i * PGDIR_SIZE;
 		if (!pgd_none(*pgd)) {
 			walk_pud(&st, pgd, addr);

arch/arm/mm/init.c

@@ -658,8 +658,8 @@ static struct section_perm ro_perms[] = {
 		.start  = (unsigned long)_stext,
 		.end    = (unsigned long)__init_begin,
 #ifdef CONFIG_ARM_LPAE
-		.mask   = ~PMD_SECT_RDONLY,
-		.prot   = PMD_SECT_RDONLY,
+		.mask   = ~L_PMD_SECT_RDONLY,
+		.prot   = L_PMD_SECT_RDONLY,
 #else
 		.mask   = ~(PMD_SECT_APX | PMD_SECT_AP_WRITE),
 		.prot   = PMD_SECT_APX | PMD_SECT_AP_WRITE,

arch/arm/mm/mmu.c

@@ -1329,8 +1329,8 @@ static void __init kmap_init(void)
 static void __init map_lowmem(void)
 {
 	struct memblock_region *reg;
-	unsigned long kernel_x_start = round_down(__pa(_stext), SECTION_SIZE);
-	unsigned long kernel_x_end = round_up(__pa(__init_end), SECTION_SIZE);
+	phys_addr_t kernel_x_start = round_down(__pa(_stext), SECTION_SIZE);
+	phys_addr_t kernel_x_end = round_up(__pa(__init_end), SECTION_SIZE);
 
 	/* Map all the lowmem memory banks. */
 	for_each_memblock(memory, reg) {

arch/arm64/include/asm/arch_timer.h

@@ -21,6 +21,7 @@
 
 #include <asm/barrier.h>
 
+#include <linux/bug.h>
 #include <linux/init.h>
 #include <linux/types.h>
 

arch/arm64/include/asm/cpu.h

@@ -39,6 +39,7 @@ struct cpuinfo_arm64 {
 	u64		reg_id_aa64pfr0;
 	u64		reg_id_aa64pfr1;
 
+	u32		reg_id_dfr0;
 	u32		reg_id_isar0;
 	u32		reg_id_isar1;
 	u32		reg_id_isar2;
@@ -51,6 +52,10 @@ struct cpuinfo_arm64 {
 	u32		reg_id_mmfr3;
 	u32		reg_id_pfr0;
 	u32		reg_id_pfr1;
+
+	u32		reg_mvfr0;
+	u32		reg_mvfr1;
+	u32		reg_mvfr2;
 };
 
 DECLARE_PER_CPU(struct cpuinfo_arm64, cpu_data);

arch/arm64/include/asm/kvm_emulate.h

@@ -41,6 +41,8 @@ void kvm_inject_pabt(struct kvm_vcpu *vcpu, unsigned long addr);
 static inline void vcpu_reset_hcr(struct kvm_vcpu *vcpu)
 {
 	vcpu->arch.hcr_el2 = HCR_GUEST_FLAGS;
+	if (test_bit(KVM_ARM_VCPU_EL1_32BIT, vcpu->arch.features))
+		vcpu->arch.hcr_el2 &= ~HCR_RW;
 }
 
 static inline unsigned long *vcpu_pc(const struct kvm_vcpu *vcpu)

arch/arm64/include/asm/processor.h

@@ -31,6 +31,7 @@
 
 #include <asm/fpsimd.h>
 #include <asm/hw_breakpoint.h>
+#include <asm/pgtable-hwdef.h>
 #include <asm/ptrace.h>
 #include <asm/types.h>
 
@@ -123,9 +124,6 @@ struct task_struct;
 /* Free all resources held by a thread. */
 extern void release_thread(struct task_struct *);
 
-/* Prepare to copy thread state - unlazy all lazy status */
-#define prepare_to_copy(tsk)	do { } while (0)
-
 unsigned long get_wchan(struct task_struct *p);
 
 #define cpu_relax()			barrier()

arch/arm64/include/asm/unistd.h

@@ -44,7 +44,7 @@
 #define __ARM_NR_compat_cacheflush	(__ARM_NR_COMPAT_BASE+2)
 #define __ARM_NR_compat_set_tls		(__ARM_NR_COMPAT_BASE+5)
 
-#define __NR_compat_syscalls		386
+#define __NR_compat_syscalls		388
 #endif
 
 #define __ARCH_WANT_SYS_CLONE

arch/arm64/include/asm/unistd32.h

@@ -795,3 +795,5 @@ __SYSCALL(__NR_getrandom, sys_getrandom)
 __SYSCALL(__NR_memfd_create, sys_memfd_create)
 #define __NR_bpf 386
 __SYSCALL(__NR_bpf, sys_bpf)
+#define __NR_execveat 387
+__SYSCALL(__NR_execveat, compat_sys_execveat)

arch/arm64/kernel/cpuinfo.c

@@ -147,6 +147,7 @@ static void cpuinfo_sanity_check(struct cpuinfo_arm64 *cur)
 	 * If we have AArch32, we care about 32-bit features for compat. These
 	 * registers should be RES0 otherwise.
 	 */
+	diff |= CHECK(id_dfr0, boot, cur, cpu);
 	diff |= CHECK(id_isar0, boot, cur, cpu);
 	diff |= CHECK(id_isar1, boot, cur, cpu);
 	diff |= CHECK(id_isar2, boot, cur, cpu);
@@ -165,6 +166,10 @@ static void cpuinfo_sanity_check(struct cpuinfo_arm64 *cur)
 	diff |= CHECK(id_pfr0, boot, cur, cpu);
 	diff |= CHECK(id_pfr1, boot, cur, cpu);
 
+	diff |= CHECK(mvfr0, boot, cur, cpu);
+	diff |= CHECK(mvfr1, boot, cur, cpu);
+	diff |= CHECK(mvfr2, boot, cur, cpu);
+
 	/*
 	 * Mismatched CPU features are a recipe for disaster. Don't even
 	 * pretend to support them.
@@ -189,6 +194,7 @@ static void __cpuinfo_store_cpu(struct cpuinfo_arm64 *info)
 	info->reg_id_aa64pfr0 = read_cpuid(ID_AA64PFR0_EL1);
 	info->reg_id_aa64pfr1 = read_cpuid(ID_AA64PFR1_EL1);
 
+	info->reg_id_dfr0 = read_cpuid(ID_DFR0_EL1);
 	info->reg_id_isar0 = read_cpuid(ID_ISAR0_EL1);
 	info->reg_id_isar1 = read_cpuid(ID_ISAR1_EL1);
 	info->reg_id_isar2 = read_cpuid(ID_ISAR2_EL1);
@@ -202,6 +208,10 @@ static void __cpuinfo_store_cpu(struct cpuinfo_arm64 *info)
 	info->reg_id_pfr0 = read_cpuid(ID_PFR0_EL1);
 	info->reg_id_pfr1 = read_cpuid(ID_PFR1_EL1);
 
+	info->reg_mvfr0 = read_cpuid(MVFR0_EL1);
+	info->reg_mvfr1 = read_cpuid(MVFR1_EL1);
+	info->reg_mvfr2 = read_cpuid(MVFR2_EL1);
+
 	cpuinfo_detect_icache_policy(info);
 
 	check_local_cpu_errata();

arch/arm64/kernel/efi.c

@@ -326,6 +326,7 @@ void __init efi_idmap_init(void)
 
 	/* boot time idmap_pg_dir is incomplete, so fill in missing parts */
 	efi_setup_idmap();
+	early_memunmap(memmap.map, memmap.map_end - memmap.map);
 }
 
 static int __init remap_region(efi_memory_desc_t *md, void **new)
@@ -380,7 +381,6 @@ static int __init arm64_enter_virtual_mode(void)
 	}
 
 	mapsize = memmap.map_end - memmap.map;
-	early_memunmap(memmap.map, mapsize);
 
 	if (efi_runtime_disabled()) {
 		pr_info("EFI runtime services will be disabled.\n");

arch/arm64/kernel/module.c

@@ -25,6 +25,7 @@
 #include <linux/mm.h>
 #include <linux/moduleloader.h>
 #include <linux/vmalloc.h>
+#include <asm/alternative.h>
 #include <asm/insn.h>
 #include <asm/sections.h>
 

arch/arm64/kernel/perf_regs.c

@@ -50,3 +50,11 @@ u64 perf_reg_abi(struct task_struct *task)
 	else
 		return PERF_SAMPLE_REGS_ABI_64;
 }
+
+void perf_get_regs_user(struct perf_regs *regs_user,
+			struct pt_regs *regs,
+			struct pt_regs *regs_user_copy)
+{
+	regs_user->regs = task_pt_regs(current);
+	regs_user->abi = perf_reg_abi(current);
+}

arch/arm64/kernel/setup.c

@@ -402,6 +402,7 @@ void __init setup_arch(char **cmdline_p)
 	request_standard_resources();
 
 	efi_idmap_init();
+	early_ioremap_reset();
 
 	unflatten_device_tree();
 

arch/arm64/kernel/smp_spin_table.c

@@ -25,6 +25,7 @@
 #include <asm/cacheflush.h>
 #include <asm/cpu_ops.h>
 #include <asm/cputype.h>
+#include <asm/io.h>
 #include <asm/smp_plat.h>
 
 extern void secondary_holding_pen(void);

arch/arm64/kvm/hyp.S

@@ -1014,6 +1014,7 @@ ENTRY(__kvm_tlb_flush_vmid_ipa)
 	 * Instead, we invalidate Stage-2 for this IPA, and the
 	 * whole of Stage-1. Weep...
 	 */
+	lsr	x1, x1, #12
 	tlbi	ipas2e1is, x1
 	/*
 	 * We have to ensure completion of the invalidation at Stage-2,

arch/arm64/kvm/reset.c

@@ -90,7 +90,6 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
 			if (!cpu_has_32bit_el1())
 				return -EINVAL;
 			cpu_reset = &default_regs_reset32;
-			vcpu->arch.hcr_el2 &= ~HCR_RW;
 		} else {
 			cpu_reset = &default_regs_reset;
 		}

arch/arm64/mm/init.c

@@ -335,14 +335,8 @@ static int keep_initrd;
 
 void free_initrd_mem(unsigned long start, unsigned long end)
 {
-	if (!keep_initrd) {
-		if (start == initrd_start)
-			start = round_down(start, PAGE_SIZE);
-		if (end == initrd_end)
-			end = round_up(end, PAGE_SIZE);
-
+	if (!keep_initrd)
 		free_reserved_area((void *)start, (void *)end, 0, "initrd");
-	}
 }
 
 static int __init keepinitrd_setup(char *__unused)

arch/blackfin/mach-bf533/boards/stamp.c

@@ -7,6 +7,7 @@
  */
 
 #include <linux/device.h>
+#include <linux/delay.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>

arch/ia64/include/asm/unistd.h

@@ -11,7 +11,7 @@
 
 
 
-#define NR_syscalls			318 /* length of syscall table */
+#define NR_syscalls			319 /* length of syscall table */
 
 /*
  * The following defines stop scripts/checksyscalls.sh from complaining about

arch/ia64/include/uapi/asm/unistd.h

@@ -331,5 +331,6 @@
 #define __NR_getrandom			1339
 #define __NR_memfd_create		1340
 #define __NR_bpf			1341
+#define __NR_execveat			1342
 
 #endif /* _UAPI_ASM_IA64_UNISTD_H */

arch/ia64/kernel/acpi.c

@@ -893,13 +893,13 @@ static int _acpi_map_lsapic(acpi_handle handle, int physid, int *pcpu)
 }
 
 /* wrapper to silence section mismatch warning */
-int __ref acpi_map_lsapic(acpi_handle handle, int physid, int *pcpu)
+int __ref acpi_map_cpu(acpi_handle handle, int physid, int *pcpu)
 {
 	return _acpi_map_lsapic(handle, physid, pcpu);
 }
-EXPORT_SYMBOL(acpi_map_lsapic);
+EXPORT_SYMBOL(acpi_map_cpu);
 
-int acpi_unmap_lsapic(int cpu)
+int acpi_unmap_cpu(int cpu)
 {
 	ia64_cpu_to_sapicid[cpu] = -1;
 	set_cpu_present(cpu, false);
@@ -910,8 +910,7 @@ int acpi_unmap_lsapic(int cpu)
 
 	return (0);
 }
-
-EXPORT_SYMBOL(acpi_unmap_lsapic);
+EXPORT_SYMBOL(acpi_unmap_cpu);
 #endif				/* CONFIG_ACPI_HOTPLUG_CPU */
 
 #ifdef CONFIG_ACPI_NUMA

arch/ia64/kernel/entry.S

@@ -1779,6 +1779,7 @@ sys_call_table:
 	data8 sys_getrandom
 	data8 sys_memfd_create			// 1340
 	data8 sys_bpf
+	data8 sys_execveat
 
 	.org sys_call_table + 8*NR_syscalls	// guard against failures to increase NR_syscalls
 #endif /* __IA64_ASM_PARAVIRTUALIZED_NATIVE */

arch/m68k/include/asm/unistd.h

@@ -4,7 +4,7 @@
 #include <uapi/asm/unistd.h>
 
 
-#define NR_syscalls		355
+#define NR_syscalls		356
 
 #define __ARCH_WANT_OLD_READDIR
 #define __ARCH_WANT_OLD_STAT

arch/m68k/include/uapi/asm/unistd.h

@@ -360,5 +360,6 @@
 #define __NR_getrandom		352
 #define __NR_memfd_create	353
 #define __NR_bpf		354
+#define __NR_execveat		355
 
 #endif /* _UAPI_ASM_M68K_UNISTD_H_ */

arch/m68k/kernel/syscalltable.S

@@ -375,4 +375,5 @@ ENTRY(sys_call_table)
 	.long sys_getrandom
 	.long sys_memfd_create
 	.long sys_bpf
+	.long sys_execveat		/* 355 */
 

arch/nios2/kernel/cpuinfo.c

@@ -72,6 +72,7 @@ void __init setup_cpuinfo(void)
 	cpuinfo.has_div = fcpu_has(cpu, "altr,has-div");
 	cpuinfo.has_mul = fcpu_has(cpu, "altr,has-mul");
 	cpuinfo.has_mulx = fcpu_has(cpu, "altr,has-mulx");
+	cpuinfo.mmu = fcpu_has(cpu, "altr,has-mmu");
 
 	if (IS_ENABLED(CONFIG_NIOS2_HW_DIV_SUPPORT) && !cpuinfo.has_div)
 		err_cpu("DIV");

arch/nios2/kernel/entry.S

@@ -365,30 +365,14 @@ ENTRY(ret_from_interrupt)
 	GET_THREAD_INFO	r1
 	ldw	r4, TI_PREEMPT_COUNT(r1)
 	bne	r4, r0, restore_all
-
-need_resched:
 	ldw	r4, TI_FLAGS(r1)		/* ? Need resched set */
 	BTBZ	r10, r4, TIF_NEED_RESCHED, restore_all
 	ldw	r4, PT_ESTATUS(sp)	/* ? Interrupts off */
 	andi	r10, r4, ESTATUS_EPIE
 	beq	r10, r0, restore_all
-	movia	r4, PREEMPT_ACTIVE
-	stw	r4, TI_PREEMPT_COUNT(r1)
-	rdctl	r10, status		/* enable intrs again */
-	ori	r10, r10 ,STATUS_PIE
-	wrctl	status, r10
-	PUSH	r1
-	call	schedule
-	POP	r1
-	mov	r4, r0
-	stw	r4, TI_PREEMPT_COUNT(r1)
-	rdctl	r10, status		/* disable intrs */
-	andi	r10, r10, %lo(~STATUS_PIE)
-	wrctl	status, r10
-	br	need_resched
-#else
-	br	restore_all
+	call	preempt_schedule_irq
 #endif
+	br	restore_all
 
 /***********************************************************************
  * A few syscall wrappers

arch/powerpc/include/asm/kexec.h

@@ -86,6 +86,11 @@ extern int overlaps_crashkernel(unsigned long start, unsigned long size);
 extern void reserve_crashkernel(void);
 extern void machine_kexec_mask_interrupts(void);
 
+static inline bool kdump_in_progress(void)
+{
+	return crashing_cpu >= 0;
+}
+
 #else /* !CONFIG_KEXEC */
 static inline void crash_kexec_secondary(struct pt_regs *regs) { }
 
@@ -106,6 +111,11 @@ static inline int crash_shutdown_unregister(crash_shutdown_t handler)
 	return 0;
 }
 
+static inline bool kdump_in_progress(void)
+{
+	return false;
+}
+
 #endif /* CONFIG_KEXEC */
 #endif /* ! __ASSEMBLY__ */
 #endif /* __KERNEL__ */

arch/powerpc/include/asm/systbl.h

@@ -366,3 +366,4 @@ SYSCALL_SPU(seccomp)
 SYSCALL_SPU(getrandom)
 SYSCALL_SPU(memfd_create)
 SYSCALL_SPU(bpf)
+COMPAT_SYS(execveat)

arch/powerpc/include/asm/thread_info.h

@@ -23,9 +23,9 @@
 #define THREAD_SIZE		(1 << THREAD_SHIFT)
 
 #ifdef CONFIG_PPC64
-#define CURRENT_THREAD_INFO(dest, sp)	clrrdi dest, sp, THREAD_SHIFT
+#define CURRENT_THREAD_INFO(dest, sp)	stringify_in_c(clrrdi dest, sp, THREAD_SHIFT)
 #else
-#define CURRENT_THREAD_INFO(dest, sp)	rlwinm dest, sp, 0, 0, 31-THREAD_SHIFT
+#define CURRENT_THREAD_INFO(dest, sp)	stringify_in_c(rlwinm dest, sp, 0, 0, 31-THREAD_SHIFT)
 #endif
 
 #ifndef __ASSEMBLY__
@@ -71,12 +71,13 @@ struct thread_info {
 #define THREAD_SIZE_ORDER	(THREAD_SHIFT - PAGE_SHIFT)
 
 /* how to get the thread information struct from C */
-register unsigned long __current_r1 asm("r1");
 static inline struct thread_info *current_thread_info(void)
 {
-	/* gcc4, at least, is smart enough to turn this into a single
-	 * rlwinm for ppc32 and clrrdi for ppc64 */
-	return (struct thread_info *)(__current_r1 & ~(THREAD_SIZE-1));
+	unsigned long val;
+
+	asm (CURRENT_THREAD_INFO(%0,1) : "=r" (val));
+
+	return (struct thread_info *)val;
 }
 
 #endif /* __ASSEMBLY__ */

arch/powerpc/include/asm/unistd.h

@@ -12,7 +12,7 @@
 #include <uapi/asm/unistd.h>
 
 
-#define __NR_syscalls		362
+#define __NR_syscalls		363
 
 #define __NR__exit __NR_exit
 #define NR_syscalls	__NR_syscalls

arch/powerpc/include/uapi/asm/unistd.h

@@ -384,5 +384,6 @@
 #define __NR_getrandom		359
 #define __NR_memfd_create	360
 #define __NR_bpf		361
+#define __NR_execveat		362
 
 #endif /* _UAPI_ASM_POWERPC_UNISTD_H_ */

arch/powerpc/kernel/machine_kexec_64.c

@@ -330,7 +330,7 @@ void default_machine_kexec(struct kimage *image)
         * using debugger IPI.
         */
 
-	if (crashing_cpu == -1)
+	if (!kdump_in_progress())
 		kexec_prepare_cpus();
 
 	pr_debug("kexec: Starting switchover sequence.\n");

arch/powerpc/kernel/smp.c

@@ -700,6 +700,7 @@ void start_secondary(void *unused)
 	smp_store_cpu_info(cpu);
 	set_dec(tb_ticks_per_jiffy);
 	preempt_disable();
+	cpu_callin_map[cpu] = 1;
 
 	if (smp_ops->setup_cpu)
 		smp_ops->setup_cpu(cpu);
@@ -738,14 +739,6 @@ void start_secondary(void *unused)
 	notify_cpu_starting(cpu);
 	set_cpu_online(cpu, true);
 
-	/*
-	 * CPU must be marked active and online before we signal back to the
-	 * master, because the scheduler needs to see the cpu_online and
-	 * cpu_active bits set.
-	 */
-	smp_wmb();
-	cpu_callin_map[cpu] = 1;
-
 	local_irq_enable();
 
 	cpu_startup_entry(CPUHP_ONLINE);

arch/powerpc/platforms/powernv/opal-wrappers.S

@@ -40,7 +40,6 @@ BEGIN_FTR_SECTION;						\
 	b	1f;						\
 END_FTR_SECTION(0, 1);						\
 	ld	r12,opal_tracepoint_refcount@toc(r2);		\
-	std	r12,32(r1);					\
 	cmpdi	r12,0;						\
 	bne-	LABEL;						\
 1:

arch/powerpc/platforms/pseries/lpar.c

@@ -43,6 +43,7 @@
 #include <asm/trace.h>
 #include <asm/firmware.h>
 #include <asm/plpar_wrappers.h>
+#include <asm/kexec.h>
 #include <asm/fadump.h>
 
 #include "pseries.h"
@@ -267,8 +268,13 @@ static void pSeries_lpar_hptab_clear(void)
 		 * out to the user, but at least this will stop us from
 		 * continuing on further and creating an even more
 		 * difficult to debug situation.
+		 *
+		 * There is a known problem when kdump'ing, if cpus are offline
+		 * the above call will fail. Rather than panicking again, keep
+		 * going and hope the kdump kernel is also little endian, which
+		 * it usually is.
 		 */
-		if (rc)
+		if (rc && !kdump_in_progress())
 			panic("Could not enable big endian exceptions");
 	}
 #endif

arch/s390/hypfs/hypfs_vm.c

@@ -231,7 +231,7 @@ failed:
 struct dbfs_d2fc_hdr {
 	u64	len;		/* Length of d2fc buffer without header */
 	u16	version;	/* Version of header */
-	char	tod_ext[16];	/* TOD clock for d2fc */
+	char	tod_ext[STORE_CLOCK_EXT_SIZE]; /* TOD clock for d2fc */
 	u64	count;		/* Number of VM guests in d2fc buffer */
 	char	reserved[30];
 } __attribute__ ((packed));

arch/s390/include/asm/irqflags.h

@@ -36,7 +36,7 @@ static inline notrace void __arch_local_irq_ssm(unsigned long flags)
 
 static inline notrace unsigned long arch_local_save_flags(void)
 {
-	return __arch_local_irq_stosm(0x00);
+	return __arch_local_irq_stnsm(0xff);
 }
 
 static inline notrace unsigned long arch_local_irq_save(void)

arch/s390/include/asm/timex.h

@@ -67,20 +67,22 @@ static inline void local_tick_enable(unsigned long long comp)
 	set_clock_comparator(S390_lowcore.clock_comparator);
 }
 
-#define CLOCK_TICK_RATE	1193180 /* Underlying HZ */
+#define CLOCK_TICK_RATE		1193180 /* Underlying HZ */
+#define STORE_CLOCK_EXT_SIZE	16	/* stcke writes 16 bytes */
 
 typedef unsigned long long cycles_t;
 
-static inline void get_tod_clock_ext(char clk[16])
+static inline void get_tod_clock_ext(char *clk)
 {
-	typedef struct { char _[sizeof(clk)]; } addrtype;
+	typedef struct { char _[STORE_CLOCK_EXT_SIZE]; } addrtype;
 
 	asm volatile("stcke %0" : "=Q" (*(addrtype *) clk) : : "cc");
 }
 
 static inline unsigned long long get_tod_clock(void)
 {
-	unsigned char clk[16];
+	unsigned char clk[STORE_CLOCK_EXT_SIZE];
+
 	get_tod_clock_ext(clk);
 	return *((unsigned long long *)&clk[1]);
 }

arch/s390/include/uapi/asm/unistd.h

@@ -289,7 +289,8 @@
 #define __NR_bpf		351
 #define __NR_s390_pci_mmio_write	352
 #define __NR_s390_pci_mmio_read		353
-#define NR_syscalls 354
+#define __NR_execveat		354
+#define NR_syscalls 355
 
 /* 
  * There are some system calls that are not present on 64 bit, some

arch/s390/kernel/syscalls.S

@@ -362,3 +362,4 @@ SYSCALL(sys_memfd_create,sys_memfd_create,compat_sys_memfd_create) /* 350 */
 SYSCALL(sys_bpf,sys_bpf,compat_sys_bpf)
 SYSCALL(sys_ni_syscall,sys_s390_pci_mmio_write,compat_sys_s390_pci_mmio_write)
 SYSCALL(sys_ni_syscall,sys_s390_pci_mmio_read,compat_sys_s390_pci_mmio_read)
+SYSCALL(sys_execveat,sys_execveat,compat_sys_execveat)

arch/s390/kernel/uprobes.c

@@ -48,6 +48,30 @@ bool arch_uprobe_xol_was_trapped(struct task_struct *tsk)
 	return false;
 }
 
+static int check_per_event(unsigned short cause, unsigned long control,
+			   struct pt_regs *regs)
+{
+	if (!(regs->psw.mask & PSW_MASK_PER))
+		return 0;
+	/* user space single step */
+	if (control == 0)
+		return 1;
+	/* over indication for storage alteration */
+	if ((control & 0x20200000) && (cause & 0x2000))
+		return 1;
+	if (cause & 0x8000) {
+		/* all branches */
+		if ((control & 0x80800000) == 0x80000000)
+			return 1;
+		/* branch into selected range */
+		if (((control & 0x80800000) == 0x80800000) &&
+		    regs->psw.addr >= current->thread.per_user.start &&
+		    regs->psw.addr <= current->thread.per_user.end)
+			return 1;
+	}
+	return 0;
+}
+
 int arch_uprobe_post_xol(struct arch_uprobe *auprobe, struct pt_regs *regs)
 {
 	int fixup = probe_get_fixup_type(auprobe->insn);
@@ -71,9 +95,13 @@ int arch_uprobe_post_xol(struct arch_uprobe *auprobe, struct pt_regs *regs)
 		if (regs->psw.addr - utask->xol_vaddr == ilen)
 			regs->psw.addr = utask->vaddr + ilen;
 	}
-	/* If per tracing was active generate trap */
-	if (regs->psw.mask & PSW_MASK_PER)
-		do_per_trap(regs);
+	if (check_per_event(current->thread.per_event.cause,
+			    current->thread.per_user.control, regs)) {
+		/* fix per address */
+		current->thread.per_event.address = utask->vaddr;
+		/* trigger per event */
+		set_pt_regs_flag(regs, PIF_PER_TRAP);
+	}
 	return 0;
 }
 
@@ -106,6 +134,7 @@ void arch_uprobe_abort_xol(struct arch_uprobe *auprobe, struct pt_regs *regs)
 	clear_thread_flag(TIF_UPROBE_SINGLESTEP);
 	regs->int_code = auprobe->saved_int_code;
 	regs->psw.addr = current->utask->vaddr;
+	current->thread.per_event.address = current->utask->vaddr;
 }
 
 unsigned long arch_uretprobe_hijack_return_addr(unsigned long trampoline,
@@ -146,17 +175,20 @@ static void adjust_psw_addr(psw_t *psw, unsigned long len)
 	__rc;						\
 })
 
-#define emu_store_ril(ptr, input)			\
+#define emu_store_ril(regs, ptr, input)			\
 ({							\
 	unsigned int mask = sizeof(*(ptr)) - 1;		\
+	__typeof__(ptr) __ptr = (ptr);			\
 	int __rc = 0;					\
 							\
 	if (!test_facility(34))				\
 		__rc = EMU_ILLEGAL_OP;			\
-	else if ((u64 __force)ptr & mask)		\
+	else if ((u64 __force)__ptr & mask)		\
 		__rc = EMU_SPECIFICATION;		\
-	else if (put_user(*(input), ptr))		\
+	else if (put_user(*(input), __ptr))		\
 		__rc = EMU_ADDRESSING;			\
+	if (__rc == 0)					\
+		sim_stor_event(regs, __ptr, mask + 1);	\
 	__rc;						\
 })
 
@@ -197,6 +229,25 @@ union split_register {
 	s16 s16[4];
 };
 
+/*
+ * If user per registers are setup to trace storage alterations and an
+ * emulated store took place on a fitting address a user trap is generated.
+ */
+static void sim_stor_event(struct pt_regs *regs, void *addr, int len)
+{
+	if (!(regs->psw.mask & PSW_MASK_PER))
+		return;
+	if (!(current->thread.per_user.control & PER_EVENT_STORE))
+		return;
+	if ((void *)current->thread.per_user.start > (addr + len))
+		return;
+	if ((void *)current->thread.per_user.end < addr)
+		return;
+	current->thread.per_event.address = regs->psw.addr;
+	current->thread.per_event.cause = PER_EVENT_STORE >> 16;
+	set_pt_regs_flag(regs, PIF_PER_TRAP);
+}
+
 /*
  * pc relative instructions are emulated, since parameters may not be
  * accessible from the xol area due to range limitations.
@@ -249,13 +300,13 @@ static void handle_insn_ril(struct arch_uprobe *auprobe, struct pt_regs *regs)
 			rc = emu_load_ril((u32 __user *)uptr, &rx->u64);
 			break;
 		case 0x07: /* sthrl */
-			rc = emu_store_ril((u16 __user *)uptr, &rx->u16[3]);
+			rc = emu_store_ril(regs, (u16 __user *)uptr, &rx->u16[3]);
 			break;
 		case 0x0b: /* stgrl */
-			rc = emu_store_ril((u64 __user *)uptr, &rx->u64);
+			rc = emu_store_ril(regs, (u64 __user *)uptr, &rx->u64);
 			break;
 		case 0x0f: /* strl */
-			rc = emu_store_ril((u32 __user *)uptr, &rx->u32[1]);
+			rc = emu_store_ril(regs, (u32 __user *)uptr, &rx->u32[1]);
 			break;
 		}
 		break;

arch/s390/kernel/vtime.c

@@ -128,8 +128,6 @@ void vtime_account_irq_enter(struct task_struct *tsk)
 	struct thread_info *ti = task_thread_info(tsk);
 	u64 timer, system;
 
-	WARN_ON_ONCE(!irqs_disabled());
-
 	timer = S390_lowcore.last_update_timer;
 	S390_lowcore.last_update_timer = get_vtimer();
 	S390_lowcore.system_timer += timer - S390_lowcore.last_update_timer;

arch/s390/mm/pgtable.c

@@ -322,11 +322,12 @@ static int gmap_alloc_table(struct gmap *gmap, unsigned long *table,
 static unsigned long __gmap_segment_gaddr(unsigned long *entry)
 {
 	struct page *page;
-	unsigned long offset;
+	unsigned long offset, mask;
 
 	offset = (unsigned long) entry / sizeof(unsigned long);
 	offset = (offset & (PTRS_PER_PMD - 1)) * PMD_SIZE;
-	page = pmd_to_page((pmd_t *) entry);
+	mask = ~(PTRS_PER_PMD * sizeof(pmd_t) - 1);
+	page = virt_to_page((void *)((unsigned long) entry & mask));
 	return page->index + offset;
 }
 

arch/s390/net/bpf_jit_comp.c

@@ -431,8 +431,8 @@ static int bpf_jit_insn(struct bpf_jit *jit, struct sock_filter *filter,
 		EMIT4_DISP(0x88500000, K);
 		break;
 	case BPF_ALU | BPF_NEG: /* A = -A */
-		/* lnr %r5,%r5 */
-		EMIT2(0x1155);
+		/* lcr %r5,%r5 */
+		EMIT2(0x1355);
 		break;
 	case BPF_JMP | BPF_JA: /* ip += K */
 		offset = addrs[i + K] + jit->start - jit->prg;
@@ -502,8 +502,8 @@ branch:		if (filter->jt == filter->jf) {
 xbranch:	/* Emit compare if the branch targets are different */
 		if (filter->jt != filter->jf) {
 			jit->seen |= SEEN_XREG;
-			/* cr %r5,%r12 */
-			EMIT2(0x195c);
+			/* clr %r5,%r12 */
+			EMIT2(0x155c);
 		}
 		goto branch;
 	case BPF_JMP | BPF_JSET | BPF_X: /* ip += (A & X) ? jt : jf */

arch/um/Kconfig.common

@@ -3,6 +3,7 @@ config UML
 	default y
 	select HAVE_ARCH_AUDITSYSCALL
 	select HAVE_UID16
+	select HAVE_FUTEX_CMPXCHG if FUTEX
 	select GENERIC_IRQ_SHOW
 	select GENERIC_CPU_DEVICES
 	select GENERIC_IO

arch/x86/boot/Makefile

@@ -51,6 +51,7 @@ targets += cpustr.h
 $(obj)/cpustr.h: $(obj)/mkcpustr FORCE
 	$(call if_changed,cpustr)
 endif
+clean-files += cpustr.h
 
 # ---------------------------------------------------------------------------
 

arch/x86/crypto/Makefile

@@ -26,7 +26,6 @@ obj-$(CONFIG_CRYPTO_GHASH_CLMUL_NI_INTEL) += ghash-clmulni-intel.o
 
 obj-$(CONFIG_CRYPTO_CRC32C_INTEL) += crc32c-intel.o
 obj-$(CONFIG_CRYPTO_SHA1_SSSE3) += sha1-ssse3.o
-obj-$(CONFIG_CRYPTO_SHA1_MB) += sha-mb/
 obj-$(CONFIG_CRYPTO_CRC32_PCLMUL) += crc32-pclmul.o
 obj-$(CONFIG_CRYPTO_SHA256_SSSE3) += sha256-ssse3.o
 obj-$(CONFIG_CRYPTO_SHA512_SSSE3) += sha512-ssse3.o
@@ -46,6 +45,7 @@ endif
 ifeq ($(avx2_supported),yes)
 	obj-$(CONFIG_CRYPTO_CAMELLIA_AESNI_AVX2_X86_64) += camellia-aesni-avx2.o
 	obj-$(CONFIG_CRYPTO_SERPENT_AVX2_X86_64) += serpent-avx2.o
+	obj-$(CONFIG_CRYPTO_SHA1_MB) += sha-mb/
 endif
 
 aes-i586-y := aes-i586-asm_32.o aes_glue.o

arch/x86/crypto/aes_ctrby8_avx-x86_64.S

@@ -208,7 +208,7 @@ ddq_add_8:
 
 	.if (klen == KEY_128)
 		.if (load_keys)
-			vmovdqa	3*16(p_keys), xkeyA
+			vmovdqa	3*16(p_keys), xkey4
 		.endif
 	.else
 		vmovdqa	3*16(p_keys), xkeyA
@@ -224,7 +224,7 @@ ddq_add_8:
 	add	$(16*by), p_in
 
 	.if (klen == KEY_128)
-		vmovdqa	4*16(p_keys), xkey4
+		vmovdqa	4*16(p_keys), xkeyB
 	.else
 		.if (load_keys)
 			vmovdqa	4*16(p_keys), xkey4
@@ -234,7 +234,12 @@ ddq_add_8:
 	.set i, 0
 	.rept by
 		club XDATA, i
-		vaesenc	xkeyA, var_xdata, var_xdata		/* key 3 */
+		/* key 3 */
+		.if (klen == KEY_128)
+			vaesenc	xkey4, var_xdata, var_xdata
+		.else
+			vaesenc	xkeyA, var_xdata, var_xdata
+		.endif
 		.set i, (i +1)
 	.endr
 
@@ -243,13 +248,18 @@ ddq_add_8:
 	.set i, 0
 	.rept by
 		club XDATA, i
-		vaesenc	xkey4, var_xdata, var_xdata		/* key 4 */
+		/* key 4 */
+		.if (klen == KEY_128)
+			vaesenc	xkeyB, var_xdata, var_xdata
+		.else
+			vaesenc	xkey4, var_xdata, var_xdata
+		.endif
 		.set i, (i +1)
 	.endr
 
 	.if (klen == KEY_128)
 		.if (load_keys)
-			vmovdqa	6*16(p_keys), xkeyB
+			vmovdqa	6*16(p_keys), xkey8
 		.endif
 	.else
 		vmovdqa	6*16(p_keys), xkeyB
@@ -267,12 +277,17 @@ ddq_add_8:
 	.set i, 0
 	.rept by
 		club XDATA, i
-		vaesenc	xkeyB, var_xdata, var_xdata		/* key 6 */
+		/* key 6 */
+		.if (klen == KEY_128)
+			vaesenc	xkey8, var_xdata, var_xdata
+		.else
+			vaesenc	xkeyB, var_xdata, var_xdata
+		.endif
 		.set i, (i +1)
 	.endr
 
 	.if (klen == KEY_128)
-		vmovdqa	8*16(p_keys), xkey8
+		vmovdqa	8*16(p_keys), xkeyB
 	.else
 		.if (load_keys)
 			vmovdqa	8*16(p_keys), xkey8
@@ -288,7 +303,7 @@ ddq_add_8:
 
 	.if (klen == KEY_128)
 		.if (load_keys)
-			vmovdqa	9*16(p_keys), xkeyA
+			vmovdqa	9*16(p_keys), xkey12
 		.endif
 	.else
 		vmovdqa	9*16(p_keys), xkeyA
@@ -297,7 +312,12 @@ ddq_add_8:
 	.set i, 0
 	.rept by
 		club XDATA, i
-		vaesenc	xkey8, var_xdata, var_xdata		/* key 8 */
+		/* key 8 */
+		.if (klen == KEY_128)
+			vaesenc	xkeyB, var_xdata, var_xdata
+		.else
+			vaesenc	xkey8, var_xdata, var_xdata
+		.endif
 		.set i, (i +1)
 	.endr
 
@@ -306,7 +326,12 @@ ddq_add_8:
 	.set i, 0
 	.rept by
 		club XDATA, i
-		vaesenc	xkeyA, var_xdata, var_xdata		/* key 9 */
+		/* key 9 */
+		.if (klen == KEY_128)
+			vaesenc	xkey12, var_xdata, var_xdata
+		.else
+			vaesenc	xkeyA, var_xdata, var_xdata
+		.endif
 		.set i, (i +1)
 	.endr
 
@@ -412,7 +437,6 @@ ddq_add_8:
 /* main body of aes ctr load */
 
 .macro do_aes_ctrmain key_len
-
 	cmp	$16, num_bytes
 	jb	.Ldo_return2\key_len
 

arch/x86/include/asm/vgtod.h

@@ -80,9 +80,11 @@ static inline unsigned int __getcpu(void)
 
 	/*
 	 * Load per CPU data from GDT.  LSL is faster than RDTSCP and
-	 * works on all CPUs.
+	 * works on all CPUs.  This is volatile so that it orders
+	 * correctly wrt barrier() and to keep gcc from cleverly
+	 * hoisting it out of the calling function.
 	 */
-	asm("lsl %1,%0" : "=r" (p) : "r" (__PER_CPU_SEG));
+	asm volatile ("lsl %1,%0" : "=r" (p) : "r" (__PER_CPU_SEG));
 
 	return p;
 }

arch/x86/kernel/acpi/boot.c

@@ -750,13 +750,13 @@ static int _acpi_map_lsapic(acpi_handle handle, int physid, int *pcpu)
 }
 
 /* wrapper to silence section mismatch warning */
-int __ref acpi_map_lsapic(acpi_handle handle, int physid, int *pcpu)
+int __ref acpi_map_cpu(acpi_handle handle, int physid, int *pcpu)
 {
 	return _acpi_map_lsapic(handle, physid, pcpu);
 }
-EXPORT_SYMBOL(acpi_map_lsapic);
+EXPORT_SYMBOL(acpi_map_cpu);
 
-int acpi_unmap_lsapic(int cpu)
+int acpi_unmap_cpu(int cpu)
 {
 #ifdef CONFIG_ACPI_NUMA
 	set_apicid_to_node(per_cpu(x86_cpu_to_apicid, cpu), NUMA_NO_NODE);
@@ -768,8 +768,7 @@ int acpi_unmap_lsapic(int cpu)
 
 	return (0);
 }
-
-EXPORT_SYMBOL(acpi_unmap_lsapic);
+EXPORT_SYMBOL(acpi_unmap_cpu);
 #endif				/* CONFIG_ACPI_HOTPLUG_CPU */
 
 int acpi_register_ioapic(acpi_handle handle, u64 phys_addr, u32 gsi_base)