Revert "uart: pl011: Rename regs with enumeration"

This reverts commit 534e14e2293d8cd714b94513686228453b21fae2 as with
this patch the serial console is broken on lots of platforms.

Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/amba-pl011.c

@@ -85,25 +85,6 @@ struct vendor_data {
 	unsigned int (*get_fifosize)(struct amba_device *dev);
 };
 
-enum reg_idx {
-	REG_DR		= UART01x_DR,
-	REG_RSR		= UART01x_RSR,
-	REG_ST_DMAWM	= ST_UART011_DMAWM,
-	REG_FR		= UART01x_FR,
-	REG_ST_LCRH_RX  = ST_UART011_LCRH_RX,
-	REG_ILPR	= UART01x_ILPR,
-	REG_IBRD	= UART011_IBRD,
-	REG_FBRD	= UART011_FBRD,
-	REG_LCRH	= UART011_LCRH,
-	REG_CR		= UART011_CR,
-	REG_IFLS	= UART011_IFLS,
-	REG_IMSC	= UART011_IMSC,
-	REG_RIS		= UART011_RIS,
-	REG_MIS		= UART011_MIS,
-	REG_ICR		= UART011_ICR,
-	REG_DMACR	= UART011_DMACR,
-};
-
 static unsigned int get_fifosize_arm(struct amba_device *dev)
 {
 	return amba_rev(dev) < 3 ? 16 : 32;
@@ -111,8 +92,8 @@ static unsigned int get_fifosize_arm(struct amba_device *dev)
 
 static struct vendor_data vendor_arm = {
 	.ifls			= UART011_IFLS_RX4_8|UART011_IFLS_TX4_8,
-	.lcrh_tx		= REG_LCRH,
-	.lcrh_rx		= REG_LCRH,
+	.lcrh_tx		= UART011_LCRH,
+	.lcrh_rx		= UART011_LCRH,
 	.oversampling		= false,
 	.dma_threshold		= false,
 	.cts_event_workaround	= false,
@@ -136,8 +117,8 @@ static unsigned int get_fifosize_st(struct amba_device *dev)
 
 static struct vendor_data vendor_st = {
 	.ifls			= UART011_IFLS_RX_HALF|UART011_IFLS_TX_HALF,
-	.lcrh_tx		= REG_LCRH,
-	.lcrh_rx		= REG_ST_LCRH_RX,
+	.lcrh_tx		= ST_UART011_LCRH_TX,
+	.lcrh_rx		= ST_UART011_LCRH_RX,
 	.oversampling		= true,
 	.dma_threshold		= true,
 	.cts_event_workaround	= true,
@@ -215,12 +196,12 @@ static int pl011_fifo_to_tty(struct uart_amba_port *uap)
 	int fifotaken = 0;
 
 	while (max_count--) {
-		status = readw(uap->port.membase + REG_FR);
+		status = readw(uap->port.membase + UART01x_FR);
 		if (status & UART01x_FR_RXFE)
 			break;
 
 		/* Take chars from the FIFO and update status */
-		ch = readw(uap->port.membase + REG_DR) |
+		ch = readw(uap->port.membase + UART01x_DR) |
 			UART_DUMMY_DR_RX;
 		flag = TTY_NORMAL;
 		uap->port.icount.rx++;
@@ -303,7 +284,7 @@ static void pl011_dma_probe(struct uart_amba_port *uap)
 	struct amba_pl011_data *plat = dev_get_platdata(uap->port.dev);
 	struct device *dev = uap->port.dev;
 	struct dma_slave_config tx_conf = {
-		.dst_addr = uap->port.mapbase + REG_DR,
+		.dst_addr = uap->port.mapbase + UART01x_DR,
 		.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
 		.direction = DMA_MEM_TO_DEV,
 		.dst_maxburst = uap->fifosize >> 1,
@@ -358,7 +339,7 @@ static void pl011_dma_probe(struct uart_amba_port *uap)
 
 	if (chan) {
 		struct dma_slave_config rx_conf = {
-			.src_addr = uap->port.mapbase + REG_DR,
+			.src_addr = uap->port.mapbase + UART01x_DR,
 			.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
 			.direction = DMA_DEV_TO_MEM,
 			.src_maxburst = uap->fifosize >> 2,
@@ -457,7 +438,7 @@ static void pl011_dma_tx_callback(void *data)
 
 	dmacr = uap->dmacr;
 	uap->dmacr = dmacr & ~UART011_TXDMAE;
-	writew(uap->dmacr, uap->port.membase + REG_DMACR);
+	writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 
 	/*
 	 * If TX DMA was disabled, it means that we've stopped the DMA for
@@ -571,7 +552,7 @@ static int pl011_dma_tx_refill(struct uart_amba_port *uap)
 	dma_dev->device_issue_pending(chan);
 
 	uap->dmacr |= UART011_TXDMAE;
-	writew(uap->dmacr, uap->port.membase + REG_DMACR);
+	writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 	uap->dmatx.queued = true;
 
 	/*
@@ -607,9 +588,9 @@ static bool pl011_dma_tx_irq(struct uart_amba_port *uap)
 	 */
 	if (uap->dmatx.queued) {
 		uap->dmacr |= UART011_TXDMAE;
-		writew(uap->dmacr, uap->port.membase + REG_DMACR);
+		writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 		uap->im &= ~UART011_TXIM;
-		writew(uap->im, uap->port.membase + REG_IMSC);
+		writew(uap->im, uap->port.membase + UART011_IMSC);
 		return true;
 	}
 
@@ -619,7 +600,7 @@ static bool pl011_dma_tx_irq(struct uart_amba_port *uap)
 	 */
 	if (pl011_dma_tx_refill(uap) > 0) {
 		uap->im &= ~UART011_TXIM;
-		writew(uap->im, uap->port.membase + REG_IMSC);
+		writew(uap->im, uap->port.membase + UART011_IMSC);
 		return true;
 	}
 	return false;
@@ -633,7 +614,7 @@ static inline void pl011_dma_tx_stop(struct uart_amba_port *uap)
 {
 	if (uap->dmatx.queued) {
 		uap->dmacr &= ~UART011_TXDMAE;
-		writew(uap->dmacr, uap->port.membase + REG_DMACR);
+		writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 	}
 }
 
@@ -660,13 +641,13 @@ static inline bool pl011_dma_tx_start(struct uart_amba_port *uap)
 			if (pl011_dma_tx_refill(uap) > 0) {
 				uap->im &= ~UART011_TXIM;
 				writew(uap->im, uap->port.membase +
-				       REG_IMSC);
+				       UART011_IMSC);
 			} else
 				ret = false;
 		} else if (!(uap->dmacr & UART011_TXDMAE)) {
 			uap->dmacr |= UART011_TXDMAE;
 			writew(uap->dmacr,
-				       uap->port.membase + REG_DMACR);
+				       uap->port.membase + UART011_DMACR);
 		}
 		return ret;
 	}
@@ -677,9 +658,9 @@ static inline bool pl011_dma_tx_start(struct uart_amba_port *uap)
 	 */
 	dmacr = uap->dmacr;
 	uap->dmacr &= ~UART011_TXDMAE;
-	writew(uap->dmacr, uap->port.membase + REG_DMACR);
+	writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 
-	if (readw(uap->port.membase + REG_FR) & UART01x_FR_TXFF) {
+	if (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF) {
 		/*
 		 * No space in the FIFO, so enable the transmit interrupt
 		 * so we know when there is space.  Note that once we've
@@ -688,13 +669,13 @@ static inline bool pl011_dma_tx_start(struct uart_amba_port *uap)
 		return false;
 	}
 
-	writew(uap->port.x_char, uap->port.membase + REG_DR);
+	writew(uap->port.x_char, uap->port.membase + UART01x_DR);
 	uap->port.icount.tx++;
 	uap->port.x_char = 0;
 
 	/* Success - restore the DMA state */
 	uap->dmacr = dmacr;
-	writew(dmacr, uap->port.membase + REG_DMACR);
+	writew(dmacr, uap->port.membase + UART011_DMACR);
 
 	return true;
 }
@@ -722,7 +703,7 @@ __acquires(&uap->port.lock)
 			     DMA_TO_DEVICE);
 		uap->dmatx.queued = false;
 		uap->dmacr &= ~UART011_TXDMAE;
-		writew(uap->dmacr, uap->port.membase + REG_DMACR);
+		writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 	}
 }
 
@@ -762,11 +743,11 @@ static int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap)
 	dma_async_issue_pending(rxchan);
 
 	uap->dmacr |= UART011_RXDMAE;
-	writew(uap->dmacr, uap->port.membase + REG_DMACR);
+	writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 	uap->dmarx.running = true;
 
 	uap->im &= ~UART011_RXIM;
-	writew(uap->im, uap->port.membase + REG_IMSC);
+	writew(uap->im, uap->port.membase + UART011_IMSC);
 
 	return 0;
 }
@@ -825,7 +806,7 @@ static void pl011_dma_rx_chars(struct uart_amba_port *uap,
 	if (dma_count == pending && readfifo) {
 		/* Clear any error flags */
 		writew(UART011_OEIS | UART011_BEIS | UART011_PEIS | UART011_FEIS,
-		       uap->port.membase + REG_ICR);
+		       uap->port.membase + UART011_ICR);
 
 		/*
 		 * If we read all the DMA'd characters, and we had an
@@ -873,7 +854,7 @@ static void pl011_dma_rx_irq(struct uart_amba_port *uap)
 
 	/* Disable RX DMA - incoming data will wait in the FIFO */
 	uap->dmacr &= ~UART011_RXDMAE;
-	writew(uap->dmacr, uap->port.membase + REG_DMACR);
+	writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 	uap->dmarx.running = false;
 
 	pending = sgbuf->sg.length - state.residue;
@@ -893,7 +874,7 @@ static void pl011_dma_rx_irq(struct uart_amba_port *uap)
 		dev_dbg(uap->port.dev, "could not retrigger RX DMA job "
 			"fall back to interrupt mode\n");
 		uap->im |= UART011_RXIM;
-		writew(uap->im, uap->port.membase + REG_IMSC);
+		writew(uap->im, uap->port.membase + UART011_IMSC);
 	}
 }
 
@@ -941,7 +922,7 @@ static void pl011_dma_rx_callback(void *data)
 		dev_dbg(uap->port.dev, "could not retrigger RX DMA job "
 			"fall back to interrupt mode\n");
 		uap->im |= UART011_RXIM;
-		writew(uap->im, uap->port.membase + REG_IMSC);
+		writew(uap->im, uap->port.membase + UART011_IMSC);
 	}
 }
 
@@ -954,7 +935,7 @@ static inline void pl011_dma_rx_stop(struct uart_amba_port *uap)
 {
 	/* FIXME.  Just disable the DMA enable */
 	uap->dmacr &= ~UART011_RXDMAE;
-	writew(uap->dmacr, uap->port.membase + REG_DMACR);
+	writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 }
 
 /*
@@ -998,7 +979,7 @@ static void pl011_dma_rx_poll(unsigned long args)
 		spin_lock_irqsave(&uap->port.lock, flags);
 		pl011_dma_rx_stop(uap);
 		uap->im |= UART011_RXIM;
-		writew(uap->im, uap->port.membase + REG_IMSC);
+		writew(uap->im, uap->port.membase + UART011_IMSC);
 		spin_unlock_irqrestore(&uap->port.lock, flags);
 
 		uap->dmarx.running = false;
@@ -1060,7 +1041,7 @@ static void pl011_dma_startup(struct uart_amba_port *uap)
 skip_rx:
 	/* Turn on DMA error (RX/TX will be enabled on demand) */
 	uap->dmacr |= UART011_DMAONERR;
-	writew(uap->dmacr, uap->port.membase + REG_DMACR);
+	writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 
 	/*
 	 * ST Micro variants has some specific dma burst threshold
@@ -1069,8 +1050,7 @@ skip_rx:
 	 */
 	if (uap->vendor->dma_threshold)
 		writew(ST_UART011_DMAWM_RX_16 | ST_UART011_DMAWM_TX_16,
-				uap->port.membase + REG_ST_DMAWM);
-
+			       uap->port.membase + ST_UART011_DMAWM);
 
 	if (uap->using_rx_dma) {
 		if (pl011_dma_rx_trigger_dma(uap))
@@ -1095,12 +1075,12 @@ static void pl011_dma_shutdown(struct uart_amba_port *uap)
 		return;
 
 	/* Disable RX and TX DMA */
-	while (readw(uap->port.membase + REG_FR) & UART01x_FR_BUSY)
+	while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_BUSY)
 		barrier();
 
 	spin_lock_irq(&uap->port.lock);
 	uap->dmacr &= ~(UART011_DMAONERR | UART011_RXDMAE | UART011_TXDMAE);
-	writew(uap->dmacr, uap->port.membase + REG_DMACR);
+	writew(uap->dmacr, uap->port.membase + UART011_DMACR);
 	spin_unlock_irq(&uap->port.lock);
 
 	if (uap->using_tx_dma) {
@@ -1201,7 +1181,7 @@ static void pl011_stop_tx(struct uart_port *port)
 	    container_of(port, struct uart_amba_port, port);
 
 	uap->im &= ~UART011_TXIM;
-	writew(uap->im, uap->port.membase + REG_IMSC);
+	writew(uap->im, uap->port.membase + UART011_IMSC);
 	pl011_dma_tx_stop(uap);
 }
 
@@ -1211,7 +1191,7 @@ static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq);
 static void pl011_start_tx_pio(struct uart_amba_port *uap)
 {
 	uap->im |= UART011_TXIM;
-	writew(uap->im, uap->port.membase + REG_IMSC);
+	writew(uap->im, uap->port.membase + UART011_IMSC);
 	pl011_tx_chars(uap, false);
 }
 
@@ -1231,7 +1211,7 @@ static void pl011_stop_rx(struct uart_port *port)
 
 	uap->im &= ~(UART011_RXIM|UART011_RTIM|UART011_FEIM|
 		     UART011_PEIM|UART011_BEIM|UART011_OEIM);
-	writew(uap->im, uap->port.membase + REG_IMSC);
+	writew(uap->im, uap->port.membase + UART011_IMSC);
 
 	pl011_dma_rx_stop(uap);
 }
@@ -1242,7 +1222,7 @@ static void pl011_enable_ms(struct uart_port *port)
 	    container_of(port, struct uart_amba_port, port);
 
 	uap->im |= UART011_RIMIM|UART011_CTSMIM|UART011_DCDMIM|UART011_DSRMIM;
-	writew(uap->im, uap->port.membase + REG_IMSC);
+	writew(uap->im, uap->port.membase + UART011_IMSC);
 }
 
 static void pl011_rx_chars(struct uart_amba_port *uap)
@@ -1262,7 +1242,7 @@ __acquires(&uap->port.lock)
 			dev_dbg(uap->port.dev, "could not trigger RX DMA job "
 				"fall back to interrupt mode again\n");
 			uap->im |= UART011_RXIM;
-			writew(uap->im, uap->port.membase + REG_IMSC);
+			writew(uap->im, uap->port.membase + UART011_IMSC);
 		} else {
 #ifdef CONFIG_DMA_ENGINE
 			/* Start Rx DMA poll */
@@ -1283,10 +1263,10 @@ static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,
 			  bool from_irq)
 {
 	if (unlikely(!from_irq) &&
-	    readw(uap->port.membase + REG_FR) & UART01x_FR_TXFF)
+	    readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
 		return false; /* unable to transmit character */
 
-	writew(c, uap->port.membase + REG_DR);
+	writew(c, uap->port.membase + UART01x_DR);
 	uap->port.icount.tx++;
 
 	return true;
@@ -1333,7 +1313,7 @@ static void pl011_modem_status(struct uart_amba_port *uap)
 {
 	unsigned int status, delta;
 
-	status = readw(uap->port.membase + REG_FR) & UART01x_FR_MODEM_ANY;
+	status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
 
 	delta = status ^ uap->old_status;
 	uap->old_status = status;
@@ -1361,15 +1341,15 @@ static void check_apply_cts_event_workaround(struct uart_amba_port *uap)
 		return;
 
 	/* workaround to make sure that all bits are unlocked.. */
-	writew(0x00, uap->port.membase + REG_ICR);
+	writew(0x00, uap->port.membase + UART011_ICR);
 
 	/*
 	 * WA: introduce 26ns(1 uart clk) delay before W1C;
 	 * single apb access will incur 2 pclk(133.12Mhz) delay,
 	 * so add 2 dummy reads
 	 */
-	dummy_read = readw(uap->port.membase + REG_ICR);
-	dummy_read = readw(uap->port.membase + REG_ICR);
+	dummy_read = readw(uap->port.membase + UART011_ICR);
+	dummy_read = readw(uap->port.membase + UART011_ICR);
 }
 
 static irqreturn_t pl011_int(int irq, void *dev_id)
@@ -1381,15 +1361,15 @@ static irqreturn_t pl011_int(int irq, void *dev_id)
 	int handled = 0;
 
 	spin_lock_irqsave(&uap->port.lock, flags);
-	imsc = readw(uap->port.membase + REG_IMSC);
-	status = readw(uap->port.membase + REG_RIS) & imsc;
+	imsc = readw(uap->port.membase + UART011_IMSC);
+	status = readw(uap->port.membase + UART011_RIS) & imsc;
 	if (status) {
 		do {
 			check_apply_cts_event_workaround(uap);
 
 			writew(status & ~(UART011_TXIS|UART011_RTIS|
 					  UART011_RXIS),
-			       uap->port.membase + REG_ICR);
+			       uap->port.membase + UART011_ICR);
 
 			if (status & (UART011_RTIS|UART011_RXIS)) {
 				if (pl011_dma_rx_running(uap))
@@ -1406,7 +1386,7 @@ static irqreturn_t pl011_int(int irq, void *dev_id)
 			if (pass_counter-- == 0)
 				break;
 
-			status = readw(uap->port.membase + REG_RIS) & imsc;
+			status = readw(uap->port.membase + UART011_RIS) & imsc;
 		} while (status != 0);
 		handled = 1;
 	}
@@ -1420,7 +1400,7 @@ static unsigned int pl011_tx_empty(struct uart_port *port)
 {
 	struct uart_amba_port *uap =
 	    container_of(port, struct uart_amba_port, port);
-	unsigned int status = readw(uap->port.membase + REG_FR);
+	unsigned int status = readw(uap->port.membase + UART01x_FR);
 	return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
 }
 
@@ -1429,7 +1409,7 @@ static unsigned int pl011_get_mctrl(struct uart_port *port)
 	struct uart_amba_port *uap =
 	    container_of(port, struct uart_amba_port, port);
 	unsigned int result = 0;
-	unsigned int status = readw(uap->port.membase + REG_FR);
+	unsigned int status = readw(uap->port.membase + UART01x_FR);
 
 #define TIOCMBIT(uartbit, tiocmbit)	\
 	if (status & uartbit)		\
@@ -1449,7 +1429,7 @@ static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl)
 	    container_of(port, struct uart_amba_port, port);
 	unsigned int cr;
 
-	cr = readw(uap->port.membase + REG_CR);
+	cr = readw(uap->port.membase + UART011_CR);
 
 #define	TIOCMBIT(tiocmbit, uartbit)		\
 	if (mctrl & tiocmbit)		\
@@ -1469,7 +1449,7 @@ static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl)
 	}
 #undef TIOCMBIT
 
-	writew(cr, uap->port.membase + REG_CR);
+	writew(cr, uap->port.membase + UART011_CR);
 }
 
 static void pl011_break_ctl(struct uart_port *port, int break_state)
@@ -1497,7 +1477,7 @@ static void pl011_quiesce_irqs(struct uart_port *port)
 	    container_of(port, struct uart_amba_port, port);
 	unsigned char __iomem *regs = uap->port.membase;
 
-	writew(readw(regs + REG_MIS), regs + REG_ICR);
+	writew(readw(regs + UART011_MIS), regs + UART011_ICR);
 	/*
 	 * There is no way to clear TXIM as this is "ready to transmit IRQ", so
 	 * we simply mask it. start_tx() will unmask it.
@@ -1511,7 +1491,7 @@ static void pl011_quiesce_irqs(struct uart_port *port)
 	 * (including tx queue), so we're also fine with start_tx()'s caller
 	 * side.
 	 */
-	writew(readw(regs + REG_IMSC) & ~UART011_TXIM, regs + REG_IMSC);
+	writew(readw(regs + UART011_IMSC) & ~UART011_TXIM, regs + UART011_IMSC);
 }
 
 static int pl011_get_poll_char(struct uart_port *port)
@@ -1526,11 +1506,11 @@ static int pl011_get_poll_char(struct uart_port *port)
 	 */
 	pl011_quiesce_irqs(port);
 
-	status = readw(uap->port.membase + REG_FR);
+	status = readw(uap->port.membase + UART01x_FR);
 	if (status & UART01x_FR_RXFE)
 		return NO_POLL_CHAR;
 
-	return readw(uap->port.membase + REG_DR);
+	return readw(uap->port.membase + UART01x_DR);
 }
 
 static void pl011_put_poll_char(struct uart_port *port,
@@ -1539,10 +1519,10 @@ static void pl011_put_poll_char(struct uart_port *port,
 	struct uart_amba_port *uap =
 	    container_of(port, struct uart_amba_port, port);
 
-	while (readw(uap->port.membase + REG_FR) & UART01x_FR_TXFF)
+	while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
 		barrier();
 
-	writew(ch, uap->port.membase + REG_DR);
+	writew(ch, uap->port.membase + UART01x_DR);
 }
 
 #endif /* CONFIG_CONSOLE_POLL */
@@ -1567,14 +1547,14 @@ static int pl011_hwinit(struct uart_port *port)
 
 	/* Clear pending error and receive interrupts */
 	writew(UART011_OEIS | UART011_BEIS | UART011_PEIS | UART011_FEIS |
-	       UART011_RTIS | UART011_RXIS, uap->port.membase + REG_ICR);
+	       UART011_RTIS | UART011_RXIS, uap->port.membase + UART011_ICR);
 
 	/*
 	 * Save interrupts enable mask, and enable RX interrupts in case if
 	 * the interrupt is used for NMI entry.
 	 */
-	uap->im = readw(uap->port.membase + REG_IMSC);
-	writew(UART011_RTIM | UART011_RXIM, uap->port.membase + REG_IMSC);
+	uap->im = readw(uap->port.membase + UART011_IMSC);
+	writew(UART011_RTIM | UART011_RXIM, uap->port.membase + UART011_IMSC);
 
 	if (dev_get_platdata(uap->port.dev)) {
 		struct amba_pl011_data *plat;
@@ -1596,14 +1576,14 @@ static void pl011_write_lcr_h(struct uart_amba_port *uap, unsigned int lcr_h)
 		 * to get this delay write read only register 10 times
 		 */
 		for (i = 0; i < 10; ++i)
-			writew(0xff, uap->port.membase + REG_MIS);
+			writew(0xff, uap->port.membase + UART011_MIS);
 		writew(lcr_h, uap->port.membase + uap->lcrh_tx);
 	}
 }
 
 static int pl011_allocate_irq(struct uart_amba_port *uap)
 {
-	writew(uap->im, uap->port.membase + REG_IMSC);
+	writew(uap->im, uap->port.membase + UART011_IMSC);
 
 	return request_irq(uap->port.irq, pl011_int, 0, "uart-pl011", uap);
 }
@@ -1619,11 +1599,11 @@ static void pl011_enable_interrupts(struct uart_amba_port *uap)
 
 	/* Clear out any spuriously appearing RX interrupts */
 	writew(UART011_RTIS | UART011_RXIS,
-	       uap->port.membase + REG_ICR);
+	       uap->port.membase + UART011_ICR);
 	uap->im = UART011_RTIM;
 	if (!pl011_dma_rx_running(uap))
 		uap->im |= UART011_RXIM;
-	writew(uap->im, uap->port.membase + REG_IMSC);
+	writew(uap->im, uap->port.membase + UART011_IMSC);
 	spin_unlock_irq(&uap->port.lock);
 }
 
@@ -1642,22 +1622,21 @@ static int pl011_startup(struct uart_port *port)
 	if (retval)
 		goto clk_dis;
 
-	writew(uap->vendor->ifls, uap->port.membase + REG_IFLS);
+	writew(uap->vendor->ifls, uap->port.membase + UART011_IFLS);
 
 	spin_lock_irq(&uap->port.lock);
 
 	/* restore RTS and DTR */
 	cr = uap->old_cr & (UART011_CR_RTS | UART011_CR_DTR);
 	cr |= UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE;
-	writew(cr, uap->port.membase + REG_CR);
+	writew(cr, uap->port.membase + UART011_CR);
 
 	spin_unlock_irq(&uap->port.lock);
 
 	/*
 	 * initialise the old status of the modem signals
 	 */
-	uap->old_status = readw(uap->port.membase + REG_FR) &
-			UART01x_FR_MODEM_ANY;
+	uap->old_status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
 
 	/* Startup DMA */
 	pl011_dma_startup(uap);
@@ -1714,11 +1693,11 @@ static void pl011_disable_uart(struct uart_amba_port *uap)
 
 	uap->autorts = false;
 	spin_lock_irq(&uap->port.lock);
-	cr = readw(uap->port.membase + REG_CR);
+	cr = readw(uap->port.membase + UART011_CR);
 	uap->old_cr = cr;
 	cr &= UART011_CR_RTS | UART011_CR_DTR;
 	cr |= UART01x_CR_UARTEN | UART011_CR_TXE;
-	writew(cr, uap->port.membase + REG_CR);
+	writew(cr, uap->port.membase + UART011_CR);
 	spin_unlock_irq(&uap->port.lock);
 
 	/*
@@ -1735,8 +1714,8 @@ static void pl011_disable_interrupts(struct uart_amba_port *uap)
 
 	/* mask all interrupts and clear all pending ones */
 	uap->im = 0;
-	writew(uap->im, uap->port.membase + REG_IMSC);
-	writew(0xffff, uap->port.membase + REG_ICR);
+	writew(uap->im, uap->port.membase + UART011_IMSC);
+	writew(0xffff, uap->port.membase + UART011_ICR);
 
 	spin_unlock_irq(&uap->port.lock);
 }
@@ -1888,8 +1867,8 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios,
 		pl011_enable_ms(port);
 
 	/* first, disable everything */
-	old_cr = readw(port->membase + REG_CR);
-	writew(0, port->membase + REG_CR);
+	old_cr = readw(port->membase + UART011_CR);
+	writew(0, port->membase + UART011_CR);
 
 	if (termios->c_cflag & CRTSCTS) {
 		if (old_cr & UART011_CR_RTS)
@@ -1922,17 +1901,17 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios,
 			quot -= 2;
 	}
 	/* Set baud rate */
-	writew(quot & 0x3f, port->membase + REG_FBRD);
-	writew(quot >> 6, port->membase + REG_IBRD);
+	writew(quot & 0x3f, port->membase + UART011_FBRD);
+	writew(quot >> 6, port->membase + UART011_IBRD);
 
 	/*
 	 * ----------v----------v----------v----------v-----
 	 * NOTE: lcrh_tx and lcrh_rx MUST BE WRITTEN AFTER
-	 * REG_FBRD & REG_IBRD.
+	 * UART011_FBRD & UART011_IBRD.
 	 * ----------^----------^----------^----------^-----
 	 */
 	pl011_write_lcr_h(uap, lcr_h);
-	writew(old_cr, port->membase + REG_CR);
+	writew(old_cr, port->membase + UART011_CR);
 
 	spin_unlock_irqrestore(&port->lock, flags);
 }
@@ -2073,9 +2052,9 @@ static void pl011_console_putchar(struct uart_port *port, int ch)
 	struct uart_amba_port *uap =
 	    container_of(port, struct uart_amba_port, port);
 
-	while (readw(uap->port.membase + REG_FR) & UART01x_FR_TXFF)
+	while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
 		barrier();
-	writew(ch, uap->port.membase + REG_DR);
+	writew(ch, uap->port.membase + UART01x_DR);
 }
 
 static void
@@ -2100,10 +2079,10 @@ pl011_console_write(struct console *co, const char *s, unsigned int count)
 	 *	First save the CR then disable the interrupts
 	 */
 	if (!uap->vendor->always_enabled) {
-		old_cr = readw(uap->port.membase + REG_CR);
+		old_cr = readw(uap->port.membase + UART011_CR);
 		new_cr = old_cr & ~UART011_CR_CTSEN;
 		new_cr |= UART01x_CR_UARTEN | UART011_CR_TXE;
-		writew(new_cr, uap->port.membase + REG_CR);
+		writew(new_cr, uap->port.membase + UART011_CR);
 	}
 
 	uart_console_write(&uap->port, s, count, pl011_console_putchar);
@@ -2113,10 +2092,10 @@ pl011_console_write(struct console *co, const char *s, unsigned int count)
 	 *	and restore the TCR
 	 */
 	do {
-		status = readw(uap->port.membase + REG_FR);
+		status = readw(uap->port.membase + UART01x_FR);
 	} while (status & UART01x_FR_BUSY);
 	if (!uap->vendor->always_enabled)
-		writew(old_cr, uap->port.membase + REG_CR);
+		writew(old_cr, uap->port.membase + UART011_CR);
 
 	if (locked)
 		spin_unlock(&uap->port.lock);
@@ -2129,7 +2108,7 @@ static void __init
 pl011_console_get_options(struct uart_amba_port *uap, int *baud,
 			     int *parity, int *bits)
 {
-	if (readw(uap->port.membase + REG_CR) & UART01x_CR_UARTEN) {
+	if (readw(uap->port.membase + UART011_CR) & UART01x_CR_UARTEN) {
 		unsigned int lcr_h, ibrd, fbrd;
 
 		lcr_h = readw(uap->port.membase + uap->lcrh_tx);
@@ -2147,13 +2126,13 @@ pl011_console_get_options(struct uart_amba_port *uap, int *baud,
 		else
 			*bits = 8;
 
-		ibrd = readw(uap->port.membase + REG_IBRD);
-		fbrd = readw(uap->port.membase + REG_FBRD);
+		ibrd = readw(uap->port.membase + UART011_IBRD);
+		fbrd = readw(uap->port.membase + UART011_FBRD);
 
 		*baud = uap->port.uartclk * 4 / (64 * ibrd + fbrd);
 
 		if (uap->vendor->oversampling) {
-			if (readw(uap->port.membase + REG_CR)
+			if (readw(uap->port.membase + UART011_CR)
 				  & ST_UART011_CR_OVSFACT)
 				*baud *= 2;
 		}
@@ -2225,10 +2204,10 @@ static struct console amba_console = {
 
 static void pl011_putc(struct uart_port *port, int c)
 {
-	while (readl(port->membase + REG_FR) & UART01x_FR_TXFF)
+	while (readl(port->membase + UART01x_FR) & UART01x_FR_TXFF)
 		;
-	writeb(c, port->membase + REG_DR);
-	while (readl(port->membase + REG_FR) & UART01x_FR_BUSY)
+	writeb(c, port->membase + UART01x_DR);
+	while (readl(port->membase + UART01x_FR) & UART01x_FR_BUSY)
 		;
 }
 
@@ -2355,8 +2334,8 @@ static int pl011_register_port(struct uart_amba_port *uap)
 	int ret;
 
 	/* Ensure interrupts from this UART are masked and cleared */
-	writew(0, uap->port.membase + REG_IMSC);
-	writew(0xffff, uap->port.membase + REG_ICR);
+	writew(0, uap->port.membase + UART011_IMSC);
+	writew(0xffff, uap->port.membase + UART011_ICR);
 
 	if (!amba_reg.state) {
 		ret = uart_register_driver(&amba_reg);