Merge tag 'omap-for-v4.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.15-rc cycle with two fixes for hangs with the
rest being compiler warning fixes and fixes for power states and devices
on various boards:

- Fix smatch issue introduced by recent omap device changes for legacy
  resources

- Fix SRAM virt to phys related boot hang affecting n900 and other omap3 hs
  devices found by pending CMA changes. While it seems that we have not hit
  this in other use cases, let's fix it to avoid a nasty and hard to find
  suprise as right now there is just luck keeping the SRAM virtual address
  to physical address translation working with the 0xffff high_mask.

- Fix am335x reading of domain state registers that only exist for the
  PM_CEFUSE domain and produce wrong results for other domains

- Fix missing setting for error code for omap device if allocation fails

- Fix missing modules_offs for omap3 MMC3 affecting n9/n950

- Fix cm_split_idlest() reading reserved registers showing wrong
  idlestatus

- Fixes to correct #phy-cells property for compiler warnings that
  recently started happening

- Add a missing OHCI remote-wakeup-connected property that I was supposed
  to merge after the ohci-omap3 to ohci-platform changes but somehow managed
  to drop. I only noticed this was missing while debugging the OHCI/EHCI GPS
  and modem hang

- Fix a system hang with GPS or modem connected to the OHCI/EHCI bus that
  typically happened within 20 - 40 minutes on an idle system. This turned
  out to be an issue caused by using the parent interrupt controller directly
  with the WUGEN + GIC stacked interrupt controller domains

- Fixes for logicpd-somlv GPMC for Ethernet and NAND that clearly
  have been broken since we changed GPMC to use the interrupt controller
  binding for some pins. And fix the wrong pin muxing for WLAN while at it

- Fixes for am437x interrupt and dma properties to fix compiler warnings
  that recently started happening

* tag 'omap-for-v4.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am437x-cm-t43: Correct the dmas property of spi0
  ARM: dts: am4372: Correct the interrupts_properties of McASP
  ARM: dts: logicpd-somlv: Fix wl127x pinmux
  ARM: dts: logicpd-som-lv: Fix gpmc addresses for NAND and enet
  ARM: dts: Fix omap4 hang with GPS connected to USB by using wakeupgen
  ARM: OMAP2+: Missing error code in omap_device_build()
  ARM: AM33xx: PRM: Remove am33xx_pwrdm_read_prev_pwrst function
  ARM: OMAP2+: Fix SRAM virt to phys translation for save_secure_ram_context
  ARM: dts: Add remote-wakeup-connected for omap OHCI
  ARM: dts: am33xx: Add missing #phy-cells to ti,am335x-usb-phy
  ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
  ARM: OMAP2+: Fix smatch found issue for omap_device
  ARM: OMAP2/3: CM: fix cm_split_idlest functionality
  ARM: OMAP3: hwmod_data: add missing module_offs for MMC3

Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/usb/am33xx-usb.txt

@@ -95,6 +95,7 @@ usb: usb@47400000 {
 		reg = <0x47401300 0x100>;
 		reg-names = "phy";
 		ti,ctrl_mod = <&ctrl_mod>;
+		#phy-cells = <0>;
 	};
 
 	usb0: usb@47401000 {
@@ -141,6 +142,7 @@ usb: usb@47400000 {
 		reg = <0x47401b00 0x100>;
 		reg-names = "phy";
 		ti,ctrl_mod = <&ctrl_mod>;
+		#phy-cells = <0>;
 	};
 
 	usb1: usb@47401800 {

arch/arm/boot/dts/am33xx.dtsi

@@ -630,6 +630,7 @@
 				reg-names = "phy";
 				status = "disabled";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb0: usb@47401000 {
@@ -678,6 +679,7 @@
 				reg-names = "phy";
 				status = "disabled";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb1: usb@47401800 {

arch/arm/boot/dts/am4372.dtsi

@@ -927,7 +927,8 @@
 			reg = <0x48038000 0x2000>,
 			      <0x46000000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <80>, <81>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 8 2>,
@@ -941,7 +942,8 @@
 			reg = <0x4803C000 0x2000>,
 			      <0x46400000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <82>, <83>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 10 2>,

arch/arm/boot/dts/am437x-cm-t43.dts

@@ -301,8 +301,8 @@
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
-	dmas = <&edma 16
-		&edma 17>;
+	dmas = <&edma 16 0
+		&edma 17 0>;
 	dma-names = "tx0", "rx0";
 
 	flash: w25q64cvzpig@0 {

arch/arm/boot/dts/dm814x.dtsi

@@ -75,6 +75,7 @@
 				reg = <0x47401300 0x100>;
 				reg-names = "phy";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb0: usb@47401000 {

arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts

@@ -72,7 +72,8 @@
 };
 
 &gpmc {
-	ranges = <1 0 0x08000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
+	ranges = <0 0 0x30000000 0x1000000	/* CS0: 16MB for NAND */
+		  1 0 0x2c000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
 
 	ethernet@gpmc {
 		pinctrl-names = "default";

arch/arm/boot/dts/logicpd-som-lv.dtsi

@@ -33,11 +33,12 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
+		#phy-cells = <0>;
 	};
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x1000000>;	/* CS0: 16MB for NAND */
+	ranges = <0 0 0x30000000 0x1000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
@@ -121,7 +122,7 @@
 
 &mmc3 {
 	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
-	pinctrl-0 = <&mmc3_pins>;
+	pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
 	pinctrl-names = "default";
 	vmmc-supply = <&wl12xx_vmmc>;
 	non-removable;
@@ -132,8 +133,8 @@
 	wlcore: wlcore@2 {
 		compatible = "ti,wl1273";
 		reg = <2>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+		interrupt-parent = <&gpio1>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 2 */
 		ref-clock-frequency = <26000000>;
 	};
 };
@@ -157,8 +158,6 @@
 			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
 			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat2 */
 			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat3 */
-			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
-			OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
 			OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
 			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs2.sdmmc_clk */
 		>;
@@ -228,6 +227,12 @@
 			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
 		>;
 	};
+	wl127x_gpio: pinmux_wl127x_gpio_pin {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
+			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
+		>;
+	};
 };
 
 &omap3_pmx_core2 {

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -90,6 +90,7 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	tfp410: encoder0 {

arch/arm/boot/dts/omap3-beagle.dts

@@ -64,6 +64,7 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;	/* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	sound {

arch/arm/boot/dts/omap3-cm-t3x.dtsi

@@ -43,12 +43,14 @@
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&hsusb1_power>;
+		#phy-cells = <0>;
 	};
 
 	/* HS USB Host PHY on PORT 2 */
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	ads7846reg: ads7846-reg {

arch/arm/boot/dts/omap3-evm-common.dtsi

@@ -29,6 +29,7 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; /* gpio_21 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	leds {

arch/arm/boot/dts/omap3-gta04.dtsi

@@ -120,6 +120,7 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+		#phy-cells = <0>;
 	};
 
 	tv0: connector {

arch/arm/boot/dts/omap3-igep0020-common.dtsi

@@ -58,6 +58,7 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
 		vcc-supply = <&hsusb1_power>;
+		#phy-cells = <0>;
 	};
 
 	tfp410: encoder {

arch/arm/boot/dts/omap3-igep0030-common.dtsi

@@ -37,6 +37,7 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;		/* gpio_54 */
+		#phy-cells = <0>;
 	};
 };
 

arch/arm/boot/dts/omap3-lilly-a83x.dtsi

@@ -51,6 +51,7 @@
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&reg_vcc3>;
+		#phy-cells = <0>;
 	};
 };
 

arch/arm/boot/dts/omap3-overo-base.dtsi

@@ -51,6 +51,7 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;	/* gpio_183 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	/* Regulator to trigger the nPoweron signal of the Wifi module */

arch/arm/boot/dts/omap3-pandora-common.dtsi

@@ -205,6 +205,7 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; /* GPIO_16 */
 		vcc-supply = <&vaux2>;
+		#phy-cells = <0>;
 	};
 
 	/* HS USB Host VBUS supply

arch/arm/boot/dts/omap3-tao3530.dtsi

@@ -46,6 +46,7 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>;	/* gpio_162 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	sound {

arch/arm/boot/dts/omap3.dtsi

@@ -715,6 +715,7 @@
 				compatible = "ti,ohci-omap3";
 				reg = <0x48064400 0x400>;
 				interrupts = <76>;
+				remote-wakeup-connected;
 			};
 
 			usbhsehci: ehci@48064800 {

arch/arm/boot/dts/omap4-droid4-xt894.dts

@@ -73,6 +73,7 @@
 	/* HS USB Host PHY on PORT 1 */
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
 	};
 
 	/* LCD regulator from sw5 source */

arch/arm/boot/dts/omap4-duovero.dtsi

@@ -43,6 +43,7 @@
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;	/* gpio_62 */
+		#phy-cells = <0>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&hsusb1phy_pins>;

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -89,6 +89,7 @@
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;   /* gpio_62 */
+		#phy-cells = <0>;
 		vcc-supply = <&hsusb1_power>;
 		clocks = <&auxclk3_ck>;
 		clock-names = "main_clk";

arch/arm/boot/dts/omap4-var-som-om44.dtsi

@@ -44,6 +44,7 @@
 
 		reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>; /* gpio 177 */
 		vcc-supply = <&vbat>;
+		#phy-cells = <0>;
 
 		clocks = <&auxclk3_ck>;
 		clock-names = "main_clk";

arch/arm/boot/dts/omap4.dtsi

@@ -1081,14 +1081,13 @@
 			usbhsohci: ohci@4a064800 {
 				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
-				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+				remote-wakeup-connected;
 			};
 
 			usbhsehci: ehci@4a064c00 {
 				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
-				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};

arch/arm/boot/dts/omap5-board-common.dtsi

@@ -73,12 +73,14 @@
 		clocks = <&auxclk1_ck>;
 		clock-names = "main_clk";
 		clock-frequency = <19200000>;
+		#phy-cells = <0>;
 	};
 
 	/* HS USB Host PHY on PORT 3 */
 	hsusb3_phy: hsusb3_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
+		#phy-cells = <0>;
 	};
 
 	tpd12s015: encoder {

arch/arm/boot/dts/omap5-cm-t54.dts

@@ -63,12 +63,14 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
+		#phy-cells = <0>;
 	};
 
 	/* HS USB Host PHY on PORT 3 */
 	hsusb3_phy: hsusb3_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
+		#phy-cells = <0>;
 	};
 
 	leds {

arch/arm/boot/dts/omap5.dtsi

@@ -940,6 +940,7 @@
 				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+				remote-wakeup-connected;
 			};
 
 			usbhsehci: ehci@4a064c00 {

arch/arm/mach-omap2/cm_common.c

@@ -68,14 +68,17 @@ void __init omap2_set_globals_cm(void __iomem *cm, void __iomem *cm2)
 int cm_split_idlest_reg(struct clk_omap_reg *idlest_reg, s16 *prcm_inst,
 			u8 *idlest_reg_id)
 {
+	int ret;
 	if (!cm_ll_data->split_idlest_reg) {
 		WARN_ONCE(1, "cm: %s: no low-level function defined\n",
 			  __func__);
 		return -EINVAL;
 	}
 
-	return cm_ll_data->split_idlest_reg(idlest_reg, prcm_inst,
+	ret = cm_ll_data->split_idlest_reg(idlest_reg, prcm_inst,
 					   idlest_reg_id);
+	*prcm_inst -= cm_base.offset;
+	return ret;
 }
 
 /**
@@ -337,6 +340,7 @@ int __init omap2_cm_base_init(void)
 		if (mem) {
 			mem->pa = res.start + data->offset;
 			mem->va = data->mem + data->offset;
+			mem->offset = data->offset;
 		}
 
 		data->np = np;

arch/arm/mach-omap2/omap-secure.c

@@ -73,6 +73,25 @@ phys_addr_t omap_secure_ram_mempool_base(void)
 	return omap_secure_memblock_base;
 }
 
+u32 omap3_save_secure_ram(void __iomem *addr, int size)
+{
+	u32 ret;
+	u32 param[5];
+
+	if (size != OMAP3_SAVE_SECURE_RAM_SZ)
+		return OMAP3_SAVE_SECURE_RAM_SZ;
+
+	param[0] = 4;		/* Number of arguments */
+	param[1] = __pa(addr);	/* Physical address for saving */
+	param[2] = 0;
+	param[3] = 1;
+	param[4] = 1;
+
+	ret = save_secure_ram_context(__pa(param));
+
+	return ret;
+}
+
 /**
  * rx51_secure_dispatcher: Routine to dispatch secure PPA API calls
  * @idx: The PPA API index

arch/arm/mach-omap2/omap-secure.h

@@ -31,6 +31,8 @@
 /* Maximum Secure memory storage size */
 #define OMAP_SECURE_RAM_STORAGE	(88 * SZ_1K)
 
+#define OMAP3_SAVE_SECURE_RAM_SZ	0x803F
+
 /* Secure low power HAL API index */
 #define OMAP4_HAL_SAVESECURERAM_INDEX	0x1a
 #define OMAP4_HAL_SAVEHW_INDEX		0x1b
@@ -65,6 +67,8 @@ extern u32 omap_smc2(u32 id, u32 falg, u32 pargs);
 extern u32 omap_smc3(u32 id, u32 process, u32 flag, u32 pargs);
 extern phys_addr_t omap_secure_ram_mempool_base(void);
 extern int omap_secure_ram_reserve_memblock(void);
+extern u32 save_secure_ram_context(u32 args_pa);
+extern u32 omap3_save_secure_ram(void __iomem *save_regs, int size);
 
 extern u32 rx51_secure_dispatcher(u32 idx, u32 process, u32 flag, u32 nargs,
 				  u32 arg1, u32 arg2, u32 arg3, u32 arg4);

arch/arm/mach-omap2/omap_device.c

@@ -391,10 +391,8 @@ omap_device_copy_resources(struct omap_hwmod *oh,
 	const char *name;
 	int error, irq = 0;
 
-	if (!oh || !oh->od || !oh->od->pdev) {
-		error = -EINVAL;
-		goto error;
-	}
+	if (!oh || !oh->od || !oh->od->pdev)
+		return -EINVAL;
 
 	np = oh->od->pdev->dev.of_node;
 	if (!np) {
@@ -516,8 +514,10 @@ struct platform_device __init *omap_device_build(const char *pdev_name,
 		goto odbs_exit1;
 
 	od = omap_device_alloc(pdev, &oh, 1);
-	if (IS_ERR(od))
+	if (IS_ERR(od)) {
+		ret = PTR_ERR(od);
 		goto odbs_exit1;
+	}
 
 	ret = platform_device_add_data(pdev, pdata, pdata_len);
 	if (ret)

arch/arm/mach-omap2/omap_hwmod_3xxx_data.c

@@ -1646,6 +1646,7 @@ static struct omap_hwmod omap3xxx_mmc3_hwmod = {
 	.main_clk	= "mmchs3_fck",
 	.prcm		= {
 		.omap2 = {
+			.module_offs = CORE_MOD,
 			.prcm_reg_id = 1,
 			.module_bit = OMAP3430_EN_MMC3_SHIFT,
 			.idlest_reg_id = 1,

arch/arm/mach-omap2/pm.h

@@ -81,10 +81,6 @@ extern unsigned int omap3_do_wfi_sz;
 /* ... and its pointer from SRAM after copy */
 extern void (*omap3_do_wfi_sram)(void);
 
-/* save_secure_ram_context function pointer and size, for copy to SRAM */
-extern int save_secure_ram_context(u32 *addr);
-extern unsigned int save_secure_ram_context_sz;
-
 extern void omap3_save_scratchpad_contents(void);
 
 #define PM_RTA_ERRATUM_i608		(1 << 0)

arch/arm/mach-omap2/pm34xx.c

@@ -48,6 +48,7 @@
 #include "prm3xxx.h"
 #include "pm.h"
 #include "sdrc.h"
+#include "omap-secure.h"
 #include "sram.h"
 #include "control.h"
 #include "vc.h"
@@ -66,7 +67,6 @@ struct power_state {
 
 static LIST_HEAD(pwrst_list);
 
-static int (*_omap_save_secure_sram)(u32 *addr);
 void (*omap3_do_wfi_sram)(void);
 
 static struct powerdomain *mpu_pwrdm, *neon_pwrdm;
@@ -121,8 +121,8 @@ static void omap3_save_secure_ram_context(void)
 		 * will hang the system.
 		 */
 		pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
-		ret = _omap_save_secure_sram((u32 *)(unsigned long)
-				__pa(omap3_secure_ram_storage));
+		ret = omap3_save_secure_ram(omap3_secure_ram_storage,
+					    OMAP3_SAVE_SECURE_RAM_SZ);
 		pwrdm_set_next_pwrst(mpu_pwrdm, mpu_next_state);
 		/* Following is for error tracking, it should not happen */
 		if (ret) {
@@ -434,15 +434,10 @@ static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
  *
  * The minimum set of functions is pushed to SRAM for execution:
  * - omap3_do_wfi for erratum i581 WA,
- * - save_secure_ram_context for security extensions.
  */
 void omap_push_sram_idle(void)
 {
 	omap3_do_wfi_sram = omap_sram_push(omap3_do_wfi, omap3_do_wfi_sz);
-
-	if (omap_type() != OMAP2_DEVICE_TYPE_GP)
-		_omap_save_secure_sram = omap_sram_push(save_secure_ram_context,
-				save_secure_ram_context_sz);
 }
 
 static void __init pm_errata_configure(void)
@@ -553,7 +548,7 @@ int __init omap3_pm_init(void)
 	clkdm_add_wkdep(neon_clkdm, mpu_clkdm);
 	if (omap_type() != OMAP2_DEVICE_TYPE_GP) {
 		omap3_secure_ram_storage =
-			kmalloc(0x803F, GFP_KERNEL);
+			kmalloc(OMAP3_SAVE_SECURE_RAM_SZ, GFP_KERNEL);
 		if (!omap3_secure_ram_storage)
 			pr_err("Memory allocation failed when allocating for secure sram context\n");
 

arch/arm/mach-omap2/prcm-common.h

@@ -528,6 +528,7 @@ struct omap_prcm_irq_setup {
 struct omap_domain_base {
 	u32 pa;
 	void __iomem *va;
+	s16 offset;
 };
 
 /**

arch/arm/mach-omap2/prm33xx.c

@@ -176,17 +176,6 @@ static int am33xx_pwrdm_read_pwrst(struct powerdomain *pwrdm)
 	return v;
 }
 
-static int am33xx_pwrdm_read_prev_pwrst(struct powerdomain *pwrdm)
-{
-	u32 v;
-
-	v = am33xx_prm_read_reg(pwrdm->prcm_offs, pwrdm->pwrstst_offs);
-	v &= AM33XX_LASTPOWERSTATEENTERED_MASK;
-	v >>= AM33XX_LASTPOWERSTATEENTERED_SHIFT;
-
-	return v;
-}
-
 static int am33xx_pwrdm_set_lowpwrstchange(struct powerdomain *pwrdm)
 {
 	am33xx_prm_rmw_reg_bits(AM33XX_LOWPOWERSTATECHANGE_MASK,
@@ -357,7 +346,6 @@ struct pwrdm_ops am33xx_pwrdm_operations = {
 	.pwrdm_set_next_pwrst		= am33xx_pwrdm_set_next_pwrst,
 	.pwrdm_read_next_pwrst		= am33xx_pwrdm_read_next_pwrst,
 	.pwrdm_read_pwrst		= am33xx_pwrdm_read_pwrst,
-	.pwrdm_read_prev_pwrst		= am33xx_pwrdm_read_prev_pwrst,
 	.pwrdm_set_logic_retst		= am33xx_pwrdm_set_logic_retst,
 	.pwrdm_read_logic_pwrst		= am33xx_pwrdm_read_logic_pwrst,
 	.pwrdm_read_logic_retst		= am33xx_pwrdm_read_logic_retst,

arch/arm/mach-omap2/sleep34xx.S

@@ -93,20 +93,13 @@ ENTRY(enable_omap3630_toggle_l2_on_restore)
 ENDPROC(enable_omap3630_toggle_l2_on_restore)
 
 /*
- * Function to call rom code to save secure ram context. This gets
- * relocated to SRAM, so it can be all in .data section. Otherwise
- * we need to initialize api_params separately.
+ * Function to call rom code to save secure ram context.
+ *
+ * r0 = physical address of the parameters
  */
-	.data
-	.align	3
 ENTRY(save_secure_ram_context)
 	stmfd	sp!, {r4 - r11, lr}	@ save registers on stack
-	adr	r3, api_params		@ r3 points to parameters
-	str	r0, [r3,#0x4]		@ r0 has sdram address
-	ldr	r12, high_mask
-	and	r3, r3, r12
-	ldr	r12, sram_phy_addr_mask
-	orr	r3, r3, r12
+	mov	r3, r0			@ physical address of parameters
 	mov	r0, #25			@ set service ID for PPA
 	mov	r12, r0			@ copy secure service ID in r12
 	mov	r1, #0			@ set task id for ROM code in r1
@@ -120,18 +113,7 @@ ENTRY(save_secure_ram_context)
 	nop
 	nop
 	ldmfd	sp!, {r4 - r11, pc}
-	.align
-sram_phy_addr_mask:
-	.word	SRAM_BASE_P
-high_mask:
-	.word	0xffff
-api_params:
-	.word	0x4, 0x0, 0x0, 0x1, 0x1
 ENDPROC(save_secure_ram_context)
-ENTRY(save_secure_ram_context_sz)
-	.word	. - save_secure_ram_context
-
-	.text
 
 /*
  * ======================