Merge tag 'asoc-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next

ASoC: Updates for v3.16

Lots of cleanup work going on in the core this release but very little
visible to external users except for the new drivers that have been
added.

 - Support for specifying aux CODECs in DT.
 - Removal of the deprecated mux and enum macros.
 - More moves towards full componentisation.
 - Removal of some unused I/O code.
 - Lots of cleanups, fixes and enhancements to the davinci, Freescale,
   Haswell and Realtek drivers.
 - Several drivers exposed directly in Kconfig for use with simple-card.
 - New drivers for Cirrus CS42L56, Realtek RT5639, RT5642 and RT5651 and
   ST STA350.

Documentation/devicetree/bindings/arm/arch_timer.txt

@@ -19,6 +19,9 @@ to deliver its interrupts via SPIs.
 
 - clock-frequency : The frequency of the main counter, in Hz. Optional.
 
+- always-on : a boolean property. If present, the timer is powered through an
+  always-on power domain, therefore it never loses context.
+
 Example:
 
 	timer {

Documentation/devicetree/bindings/ata/apm-xgene.txt

@@ -24,6 +24,7 @@ Required properties:
   * "sata-phy" for the SATA 6.0Gbps PHY
 
 Optional properties:
+- dma-coherent		: Present if dma operations are coherent
 - status		: Shall be "ok" if enabled or "disabled" if disabled.
 			  Default is "ok".
 
@@ -55,6 +56,7 @@ Example:
 			      <0x0 0x1f22e000 0x0 0x1000>,
 			      <0x0 0x1f227000 0x0 0x1000>;
 			interrupts = <0x0 0x87 0x4>;
+			dma-coherent;
 			status = "ok";
 			clocks = <&sataclk 0>;
 			phys = <&phy2 0>;
@@ -69,6 +71,7 @@ Example:
 			      <0x0 0x1f23e000 0x0 0x1000>,
 			      <0x0 0x1f237000 0x0 0x1000>;
 			interrupts = <0x0 0x88 0x4>;
+			dma-coherent;
 			status = "ok";
 			clocks = <&sataclk 0>;
 			phys = <&phy3 0>;

Documentation/devicetree/bindings/mfd/mc13xxx.txt

@@ -10,6 +10,9 @@ Optional properties:
 - fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used
 
 Sub-nodes:
+- codec: Contain the Audio Codec node.
+  - adc-port: Contain PMIC SSI port number used for ADC.
+  - dac-port: Contain PMIC SSI port number used for DAC.
 - leds : Contain the led nodes and initial register values in property
   "led-control". Number of register depends of used IC, for MC13783 is 6,
   for MC13892 is 4, for MC34708 is 1. See datasheet for bits definitions of

Documentation/devicetree/bindings/net/arc_emac.txt

@@ -4,11 +4,15 @@ Required properties:
 - compatible: Should be "snps,arc-emac"
 - reg: Address and length of the register set for the device
 - interrupts: Should contain the EMAC interrupts
-- clock-frequency: CPU frequency. It is needed to calculate and set polling
-period of EMAC.
 - max-speed: see ethernet.txt file in the same directory.
 - phy: see ethernet.txt file in the same directory.
 
+Clock handling:
+The clock frequency is needed to calculate and set polling period of EMAC.
+It must be provided by one of:
+- clock-frequency: CPU frequency.
+- clocks: reference to the clock supplying the EMAC.
+
 Child nodes of the driver are the individual PHY devices connected to the
 MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus.
 
@@ -19,7 +23,11 @@ Examples:
 		reg = <0xc0fc2000 0x3c>;
 		interrupts = <6>;
 		mac-address = [ 00 11 22 33 44 55 ];
+
 		clock-frequency = <80000000>;
+		/* or */
+		clocks = <&emac_clock>;
+
 		max-speed = <100>;
 		phy = <&phy0>;
 

Documentation/devicetree/bindings/net/socfpga-dwmac.txt

@@ -23,5 +23,5 @@ gmac0: ethernet@ff700000 {
 	interrupt-names = "macirq";
 	mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */
 	clocks = <&emac_0_clk>;
-	clocks-names = "stmmaceth";
+	clock-names = "stmmaceth";
 };

Documentation/devicetree/bindings/net/stmmac.txt

@@ -33,7 +33,7 @@ Optional properties:
 - max-frame-size: See ethernet.txt file in the same directory
 - clocks: If present, the first clock should be the GMAC main clock,
   further clocks may be specified in derived bindings.
-- clocks-names: One name for each entry in the clocks property, the
+- clock-names: One name for each entry in the clocks property, the
   first one should be "stmmaceth".
 
 Examples:

Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt

@@ -83,7 +83,7 @@ Example:
 		reg 		= <0xfe61f080 0x4>;
 		reg-names	= "irqmux";
 		interrupts 	= <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
-		interrupts-names = "irqmux";
+		interrupt-names	= "irqmux";
 		ranges 		= <0 0xfe610000 0x5000>;
 
 		PIO0: gpio@fe610000 {
@@ -165,7 +165,7 @@ sdhci0:sdhci@fe810000{
 	interrupt-parent = <&PIO3>;
 	#interrupt-cells = <2>;
 	interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; /* Interrupt line via PIO3-3 */
-	interrupts-names = "card-detect";
+	interrupt-names = "card-detect";
 	pinctrl-names = "default";
 	pinctrl-0	= <&pinctrl_mmc>;
 };

Documentation/devicetree/bindings/sound/ak4104.txt

@@ -8,6 +8,8 @@ Required properties:
 
   - reg : The chip select number on the SPI bus
 
+  - vdd-supply : A regulator node, providing 2.7V - 3.6V
+
 Optional properties:
 
   - reset-gpio : a GPIO spec for the reset pin. If specified, it will be
@@ -19,4 +21,5 @@ spdif: ak4104@0 {
 	compatible = "asahi-kasei,ak4104";
 	reg = <0>;
 	spi-max-frequency = <5000000>;
+	vdd-supply = <&vdd_3v3_reg>;
 };

Documentation/devicetree/bindings/sound/alc5623.txt

@@ -0,0 +1,25 @@
+ALC5621/ALC5622/ALC5623 audio Codec
+
+Required properties:
+
+ - compatible:	"realtek,alc5623"
+ - reg:		the I2C address of the device.
+
+Optional properties:
+
+ - add-ctrl:	  Default register value for Reg-40h, Additional Control
+		  Register. If absent or has the value of 0, the
+		  register is untouched.
+
+ - jack-det-ctrl: Default register value for Reg-5Ah, Jack Detect
+		  Control Register. If absent or has value 0, the
+		  register is untouched.
+
+Example:
+
+	alc5621: alc5621@1a {
+		compatible = "alc5621";
+		reg = <0x1a>;
+		add-ctrl = <0x3700>;
+		jack-det-ctrl = <0x4810>;
+	};

Documentation/devicetree/bindings/sound/cs42l56.txt

@@ -0,0 +1,63 @@
+CS42L52 audio CODEC
+
+Required properties:
+
+  - compatible : "cirrus,cs42l56"
+
+  - reg : the I2C address of the device for I2C
+
+  - VA-supply, VCP-supply, VLDO-supply : power supplies for the device,
+  as covered in Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+  - cirrus,gpio-nreset : GPIO controller's phandle and the number
+  of the GPIO used to reset the codec.
+
+  - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
+  Allowable values of 0x00 through 0x0F. These are raw values written to the
+  register, not the actual frequency. The frequency is determined by the following.
+  Frequency = MCLK / 4 * (N+2)
+  N = chgfreq_val
+  MCLK = Where MCLK is the frequency of the mclk signal after the MCLKDIV2 circuit.
+
+  - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured
+  as a pseudo-differential input referenced to AIN1REF/AIN3A.
+
+  - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured
+  as a pseudo-differential input referenced to AIN2REF/AIN3B.
+
+  - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin.
+  0 = 0.5 x VA
+  1 = 0.6 x VA
+  2 = 0.7 x VA
+  3 = 0.8 x VA
+  4 = 0.83 x VA
+  5 = 0.91 x VA
+
+  - cirrus,adaptive-pwr-cfg : Configures how the power to the Headphone and Lineout
+  Amplifiers adapt to the output signal levels.
+  0 = Adapt to Volume Mode. Voltage level determined by the sum of the relevant volume settings.
+  1 = Fixed - Headphone and Line Amp supply = + or - VCP/2.
+  2 = Fixed - Headphone and Line Amp supply = + or - VCP.
+  3 = Adapted to Signal; Voltage level is dynamically determined by the output signal.
+
+  - cirrus,hpf-left-freq, hpf-right-freq : Sets the corner frequency (-3dB point) for the internal High-Pass
+  Filter.
+  0 = 1.8Hz
+  1 = 119Hz
+  2 = 236Hz
+  3 = 464Hz
+
+
+Example:
+
+codec: codec@4b {
+	compatible = "cirrus,cs42l56";
+	reg = <0x4b>;
+	gpio-reset = <&gpio 10 0>;
+	cirrus,chgfreq-divisor = <0x05>;
+	cirrus.ain1_ref_cfg;
+	cirrus,micbias-lvl = <5>;
+	VA-supply = <&reg_audio>;
+};

Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt

@@ -47,7 +47,7 @@ mcasp0: mcasp0@1d00000 {
 	reg = <0x100000 0x3000>;
 	reg-names "mpu";
 	interrupts = <82>, <83>;
-	interrupts-names = "tx", "rx";
+	interrupt-names = "tx", "rx";
 	op-mode = <0>;		/* MCASP_IIS_MODE */
 	tdm-slots = <2>;
 	serial-dir = <

Documentation/devicetree/bindings/sound/fsl-sai.txt

@@ -7,10 +7,11 @@ codec/DSP interfaces.
 
 
 Required properties:
-- compatible: Compatible list, contains "fsl,vf610-sai".
+- compatible: Compatible list, contains "fsl,vf610-sai" or "fsl,imx6sx-sai".
 - reg: Offset and length of the register set for the device.
 - clocks: Must contain an entry for each entry in clock-names.
-- clock-names : Must include the "sai" entry.
+- clock-names : Must include the "bus" for register access and "mclk1" "mclk2"
+  "mclk3" for bit clock and frame clock providing.
 - dmas : Generic dma devicetree binding as described in
   Documentation/devicetree/bindings/dma/dma.txt.
 - dma-names : Two dmas have to be defined, "tx" and "rx".
@@ -30,8 +31,10 @@ sai2: sai@40031000 {
 	      reg = <0x40031000 0x1000>;
 	      pinctrl-names = "default";
 	      pinctrl-0 = <&pinctrl_sai2_1>;
-	      clocks = <&clks VF610_CLK_SAI2>;
-	      clock-names = "sai";
+	      clocks = <&clks VF610_CLK_PLATFORM_BUS>,
+		     <&clks VF610_CLK_SAI2>,
+		     <&clks 0>, <&clks 0>;
+	      clock-names = "bus", "mclk1", "mclk2", "mclk3";
 	      dma-names = "tx", "rx";
 	      dmas = <&edma0 0 VF610_EDMA_MUXID0_SAI2_TX>,
 		   <&edma0 0 VF610_EDMA_MUXID0_SAI2_RX>;

Documentation/devicetree/bindings/sound/max98095.txt

@@ -0,0 +1,16 @@
+MAX98095 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : "maxim,max98095".
+
+- reg : The I2C address of the device.
+
+Example:
+
+max98095: codec@11 {
+	compatible = "maxim,max98095";
+	reg = <0x11>;
+};

Documentation/devicetree/bindings/sound/nokia,rx51.txt

@@ -0,0 +1,27 @@
+* Nokia N900 audio setup
+
+Required properties:
+- compatible: Should contain "nokia,n900-audio"
+- nokia,cpu-dai: phandle for the McBSP node
+- nokia,audio-codec: phandles for the main TLV320AIC3X node and the
+                     auxiliary TLV320AIC3X node (in this order)
+- nokia,headphone-amplifier: phandle for the TPA6130A2 node
+- tvout-selection-gpios: GPIO for tvout selection
+- jack-detection-gpios: GPIO for jack detection
+- eci-switch-gpios: GPIO for ECI (Enhancement Control Interface) switch
+- speaker-amplifier-gpios: GPIO for speaker amplifier
+
+Example:
+
+sound {
+	compatible = "nokia,n900-audio";
+
+	nokia,cpu-dai = <&mcbsp2>;
+	nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>;
+	nokia,headphone-amplifier = <&tpa6130a2>;
+
+	tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */
+	jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */
+	eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */
+	speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
+};

Documentation/devicetree/bindings/sound/rt5640.txt

@@ -1,10 +1,10 @@
-RT5640 audio CODEC
+RT5640/RT5639 audio CODEC
 
 This device supports I2C only.
 
 Required properties:
 
-- compatible : "realtek,rt5640".
+- compatible : One of "realtek,rt5640" or "realtek,rt5639".
 
 - reg : The I2C address of the device.
 
@@ -18,7 +18,7 @@ Optional properties:
 
 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
 
-Pins on the device (for linking into audio routes):
+Pins on the device (for linking into audio routes) for RT5639/RT5640:
 
   * DMIC1
   * DMIC2
@@ -31,13 +31,16 @@ Pins on the device (for linking into audio routes):
   * HPOR
   * LOUTL
   * LOUTR
-  * MONOP
-  * MONON
   * SPOLP
   * SPOLN
   * SPORP
   * SPORN
 
+Additional pins on the device for RT5640:
+
+  * MONOP
+  * MONON
+
 Example:
 
 rt5640 {

Documentation/devicetree/bindings/sound/simple-card.txt

@@ -1,6 +1,6 @@
 Simple-Card:
 
-Simple-Card specifies audio DAI connection of SoC <-> codec.
+Simple-Card specifies audio DAI connections of SoC <-> codec.
 
 Required properties:
 
@@ -10,26 +10,51 @@ Optional properties:
 
 - simple-audio-card,name		: User specified audio sound card name, one string
 					  property.
-- simple-audio-card,format		: CPU/CODEC common audio format.
-					  "i2s", "right_j", "left_j" , "dsp_a"
-					  "dsp_b", "ac97", "pdm", "msb", "lsb"
 - simple-audio-card,widgets		: Please refer to widgets.txt.
 - simple-audio-card,routing		: A list of the connections between audio components.
 					  Each entry is a pair of strings, the first being the
 					  connection's sink, the second being the connection's
 					  source.
-- dai-tdm-slot-num			: Please refer to tdm-slot.txt.
-- dai-tdm-slot-width			: Please refer to tdm-slot.txt.
+Optional subnodes:
+
+- simple-audio-card,dai-link		: Container for dai-link level
+					  properties and the CPU and CODEC
+					  sub-nodes. This container may be
+					  omitted when the card has only one
+					  DAI link. See the examples and the
+					  section bellow.
+
+Dai-link subnode properties and subnodes:
+
+If dai-link subnode is omitted and the subnode properties are directly
+under "sound"-node the subnode property and subnode names have to be
+prefixed with "simple-audio-card,"-prefix.
 
-Required subnodes:
+Required dai-link subnodes:
 
-- simple-audio-card,dai-link		: container for the CPU and CODEC sub-nodes
-					  This container may be omitted when the
-					  card has only one DAI link.
-					  See the examples.
+- cpu					: CPU   sub-node
+- codec					: CODEC sub-node
 
-- simple-audio-card,cpu			: CPU   sub-node
-- simple-audio-card,codec		: CODEC sub-node
+Optional dai-link subnode properties:
+
+- format				: CPU/CODEC common audio format.
+					  "i2s", "right_j", "left_j" , "dsp_a"
+					  "dsp_b", "ac97", "pdm", "msb", "lsb"
+- frame-master				: Indicates dai-link frame master.
+					  phandle to a cpu or codec subnode.
+- bitclock-master			: Indicates dai-link bit clock master.
+					  phandle to a cpu or codec subnode.
+- bitclock-inversion			: bool property. Add this if the
+					  dai-link uses bit clock inversion.
+- frame-inversion			: bool property. Add this if the
+					  dai-link uses frame clock inversion.
+
+For backward compatibility the frame-master and bitclock-master
+properties can be used as booleans in codec subnode to indicate if the
+codec is the dai-link frame or bit clock master. In this case there
+should be no dai-link node, the same properties should not be present
+at sound-node level, and the bitclock-inversion and frame-inversion
+properties should also be placed in the codec node if needed.
 
 Required CPU/CODEC subnodes properties:
 
@@ -37,29 +62,21 @@ Required CPU/CODEC subnodes properties:
 
 Optional CPU/CODEC subnodes properties:
 
-- format				: CPU/CODEC specific audio format if needed.
-					  see simple-audio-card,format
-- frame-master				: bool property. add this if subnode is frame master
-- bitclock-master			: bool property. add this if subnode is bitclock master
-- bitclock-inversion			: bool property. add this if subnode has clock inversion
-- frame-inversion			: bool property. add this if subnode has frame inversion
+- dai-tdm-slot-num			: Please refer to tdm-slot.txt.
+- dai-tdm-slot-width			: Please refer to tdm-slot.txt.
 - clocks / system-clock-frequency	: specify subnode's clock if needed.
 					  it can be specified via "clocks" if system has
 					  clock node (= common clock), or "system-clock-frequency"
 					  (if system doens't support common clock)
 
-Note:
- * For 'format', 'frame-master', 'bitclock-master', 'bitclock-inversion' and
-   'frame-inversion', the simple card will use the settings of CODEC for both
-   CPU and CODEC sides as we need to keep the settings identical for both ends
-   of the link.
-
 Example 1 - single DAI link:
 
 sound {
 	compatible = "simple-audio-card";
 	simple-audio-card,name = "VF610-Tower-Sound-Card";
 	simple-audio-card,format = "left_j";
+	simple-audio-card,bitclock-master = <&dailink0_master>;
+	simple-audio-card,frame-master = <&dailink0_master>;
 	simple-audio-card,widgets =
 		"Microphone", "Microphone Jack",
 		"Headphone", "Headphone Jack",
@@ -69,17 +86,12 @@ sound {
 		"Headphone Jack", "HP_OUT",
 		"External Speaker", "LINE_OUT";
 
-	dai-tdm-slot-num = <2>;
-	dai-tdm-slot-width = <8>;
-
 	simple-audio-card,cpu {
 		sound-dai = <&sh_fsi2 0>;
 	};
 
-	simple-audio-card,codec {
+	dailink0_master: simple-audio-card,codec {
 		sound-dai = <&ak4648>;
-		bitclock-master;
-		frame-master;
 		clocks = <&osc>;
 	};
 };
@@ -105,31 +117,31 @@ Example 2 - many DAI links:
 sound {
 	compatible = "simple-audio-card";
 	simple-audio-card,name = "Cubox Audio";
-	simple-audio-card,format = "i2s";
 
 	simple-audio-card,dai-link@0 {		/* I2S - HDMI */
-		simple-audio-card,cpu {
+		format = "i2s";
+		cpu {
 			sound-dai = <&audio1 0>;
 		};
-		simple-audio-card,codec {
+		codec {
 			sound-dai = <&tda998x 0>;
 		};
 	};
 
 	simple-audio-card,dai-link@1 {		/* S/PDIF - HDMI */
-		simple-audio-card,cpu {
+		cpu {
 			sound-dai = <&audio1 1>;
 		};
-		simple-audio-card,codec {
+		codec {
 			sound-dai = <&tda998x 1>;
 		};
 	};
 
 	simple-audio-card,dai-link@2 {		/* S/PDIF - S/PDIF */
-		simple-audio-card,cpu {
+		cpu {
 			sound-dai = <&audio1 1>;
 		};
-		simple-audio-card,codec {
+		codec {
 			sound-dai = <&spdif_codec>;
 		};
 	};

Documentation/devicetree/bindings/sound/snow.txt

@@ -0,0 +1,17 @@
+Audio Binding for Snow boards
+
+Required properties:
+- compatible : Can be one of the following,
+			"google,snow-audio-max98090" or
+			"google,snow-audio-max98095"
+- samsung,i2s-controller: The phandle of the Samsung I2S controller
+- samsung,audio-codec: The phandle of the audio codec
+
+Example:
+
+sound {
+		compatible = "google,snow-audio-max98095";
+
+		samsung,i2s-controller = <&i2s0>;
+		samsung,audio-codec = <&max98095>;
+};

Documentation/devicetree/bindings/sound/st,sta350.txt

@@ -0,0 +1,131 @@
+STA350 audio CODEC
+
+The driver for this device only supports I2C.
+
+Required properties:
+
+  - compatible: "st,sta350"
+  - reg: the I2C address of the device for I2C
+  - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the codec starts.
+
+  - power-down-gpios: a GPIO spec for the power down pin. If specified,
+		      it will be deasserted before communication to the codec
+		      starts.
+
+  - vdd-dig-supply: regulator spec, providing 3.3V
+  - vdd-pll-supply: regulator spec, providing 3.3V
+  - vcc-supply: regulator spec, providing 5V - 26V
+
+Optional properties:
+
+  -  st,output-conf: number, Selects the output configuration:
+	0: 2-channel (full-bridge) power, 2-channel data-out
+	1: 2 (half-bridge). 1 (full-bridge) on-board power
+	2: 2 Channel (Full-Bridge) Power, 1 Channel FFX
+	3: 1 Channel Mono-Parallel
+	If parameter is missing, mode 0 will be enabled.
+	This property has to be specified as '/bits/ 8' value.
+
+  -  st,ch1-output-mapping: Channel 1 output mapping
+  -  st,ch2-output-mapping: Channel 2 output mapping
+  -  st,ch3-output-mapping: Channel 3 output mapping
+	0: Channel 1
+	1: Channel 2
+	2: Channel 3
+	If parameter is missing, channel 1 is choosen.
+	This properties have to be specified as '/bits/ 8' values.
+
+  -  st,thermal-warning-recover:
+	If present, thermal warning recovery is enabled.
+
+  -  st,thermal-warning-adjustment:
+	If present, thermal warning adjustment is enabled.
+
+  -  st,fault-detect-recovery:
+	If present, then fault recovery will be enabled.
+
+  -  st,ffx-power-output-mode: string
+	The FFX power output mode selects how the FFX output timing is
+	configured. Must be one of these values:
+	  -  "drop-compensation"
+	  -  "tapered-compensation"
+	  -  "full-power-mode"
+	  -  "variable-drop-compensation" (default)
+
+  -  st,drop-compensation-ns: number
+	Only required for "st,ffx-power-output-mode" ==
+	"variable-drop-compensation".
+	Specifies the drop compensation in nanoseconds.
+	The value must be in the range of 0..300, and only
+	multiples of 20 are allowed. Default is 140ns.
+
+  -  st,overcurrent-warning-adjustment:
+	If present, overcurrent warning adjustment is enabled.
+
+  -  st,max-power-use-mpcc:
+	If present, then MPCC bits are used for MPC coefficients,
+	otherwise standard MPC coefficients are used.
+
+  -  st,max-power-corr:
+	If present, power bridge correction for THD reduction near maximum
+	power output is enabled.
+
+  -  st,am-reduction-mode:
+	If present, FFX mode runs in AM reduction mode, otherwise normal
+	FFX mode is used.
+
+  -  st,odd-pwm-speed-mode:
+	If present, PWM speed mode run on odd speed mode (341.3 kHz) on all
+	channels. If not present, normal PWM spped mode (384 kHz) will be used.
+
+  -  st,distortion-compensation:
+	If present, distortion compensation variable uses DCC coefficient.
+	If not present, preset DC coefficient is used.
+
+  -  st,invalid-input-detect-mute:
+	If present, automatic invalid input detect mute is enabled.
+
+  -  st,activate-mute-output:
+	If present, a mute output will be activated in ase the volume will
+	reach a value lower than -76 dBFS.
+
+  -  st,bridge-immediate-off:
+	If present, the bridge will be switched off immediately after the
+	power-down-gpio goes low. Otherwise, the bridge will wait for 13
+	million clock cycles to pass before shutting down.
+
+  -  st,noise-shape-dc-cut:
+	If present, the noise-shaping technique on the DC cutoff filter are
+	enabled.
+
+  -  st,powerdown-master-volume:
+	If present, the power-down pin and I2C power-down functions will
+	act on the master volume. Otherwise, the functions will act on the
+	mute commands.
+
+  -  st,powerdown-delay-divider:
+	If present, the bridge power-down time will be divided by the provided
+	value. If not specified, a divider of 1 will be used. Allowed values
+	are 1, 2, 4, 8, 16, 32, 64 and 128.
+	This property has to be specified as '/bits/ 8' value.
+
+Example:
+
+codec: sta350@38 {
+	compatible = "st,sta350";
+	reg = <0x1c>;
+	reset-gpios = <&gpio1 19 0>;
+	power-down-gpios = <&gpio1 16 0>;
+	st,output-conf = /bits/ 8  <0x3>;	// set output to 2-channel
+						// (full-bridge) power,
+						// 2-channel data-out
+	st,ch1-output-mapping = /bits/ 8 <0>;	// set channel 1 output ch 1
+	st,ch2-output-mapping = /bits/ 8 <0>;	// set channel 2 output ch 1
+	st,ch3-output-mapping = /bits/ 8 <0>;	// set channel 3 output ch 1
+	st,max-power-correction;		// enables power bridge
+						// correction for THD reduction
+						// near maximum power output
+	st,invalid-input-detect-mute;		// mute if no valid digital
+						// audio signal is provided.
+};

Documentation/input/elantech.txt

@@ -504,9 +504,12 @@ byte 5:
 * reg_10
 
    bit   7   6   5   4   3   2   1   0
-         0   0   0   0   0   0   0   A
+         0   0   0   0   R   F   T   A
 
          A: 1 = enable absolute tracking
+         T: 1 = enable two finger mode auto correct
+         F: 1 = disable ABS Position Filter
+         R: 1 = enable real hardware resolution
 
 6.2 Native absolute mode 6 byte packet format
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Documentation/networking/scaling.txt

@@ -429,7 +429,7 @@ RPS and RFS were introduced in kernel 2.6.35. XPS was incorporated into
 (therbert@google.com)
 
 Accelerated RFS was introduced in 2.6.35. Original patches were
-submitted by Ben Hutchings (bhutchings@solarflare.com)
+submitted by Ben Hutchings (bwh@kernel.org)
 
 Authors:
 Tom Herbert (therbert@google.com)

MAINTAINERS

@@ -2245,12 +2245,6 @@ L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/host/ohci-ep93xx.c
 
-CIRRUS LOGIC CS4270 SOUND DRIVER
-M:	Timur Tabi <timur@tabi.org>
-L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
-S:	Odd Fixes
-F:	sound/soc/codecs/cs4270*
-
 CIRRUS LOGIC AUDIO CODEC DRIVERS
 M:	Brian Austin <brian.austin@cirrus.com>
 M:	Paul Handrigan <Paul.Handrigan@cirrus.com>
@@ -3485,6 +3479,12 @@ S:	Maintained
 F:	drivers/extcon/
 F:	Documentation/extcon/
 
+EXYNOS DP DRIVER
+M:	Jingoo Han <jg1.han@samsung.com>
+L:	dri-devel@lists.freedesktop.org
+S:	Maintained
+F:	drivers/gpu/drm/exynos/exynos_dp*
+
 EXYNOS MIPI DISPLAY DRIVERS
 M:	Inki Dae <inki.dae@samsung.com>
 M:	Donghwa Lee <dh09.lee@samsung.com>
@@ -3550,7 +3550,7 @@ F:	include/scsi/libfcoe.h
 F:	include/uapi/scsi/fc/
 
 FILE LOCKING (flock() and fcntl()/lockf())
-M:	Jeff Layton <jlayton@redhat.com>
+M:	Jeff Layton <jlayton@poochiereds.net>
 M:	J. Bruce Fields <bfields@fieldses.org>
 L:	linux-fsdevel@vger.kernel.org
 S:	Maintained
@@ -5108,14 +5108,19 @@ F:	drivers/s390/kvm/
 
 KERNEL VIRTUAL MACHINE (KVM) FOR ARM
 M:	Christoffer Dall <christoffer.dall@linaro.org>
+M:	Marc Zyngier <marc.zyngier@arm.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	kvmarm@lists.cs.columbia.edu
 W:	http://systems.cs.columbia.edu/projects/kvm-arm
 S:	Supported
 F:	arch/arm/include/uapi/asm/kvm*
 F:	arch/arm/include/asm/kvm*
 F:	arch/arm/kvm/
+F:	virt/kvm/arm/
+F:	include/kvm/arm_*
 
 KERNEL VIRTUAL MACHINE FOR ARM64 (KVM/arm64)
+M:	Christoffer Dall <christoffer.dall@linaro.org>
 M:	Marc Zyngier <marc.zyngier@arm.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	kvmarm@lists.cs.columbia.edu
@@ -7277,7 +7282,6 @@ F:	drivers/video/aty/aty128fb.c
 RALINK RT2X00 WIRELESS LAN DRIVER
 P:	rt2x00 project
 M:	Ivo van Doorn <IvDoorn@gmail.com>
-M:	Gertjan van Wingerde <gwingerde@gmail.com>
 M:	Helmut Schaa <helmut.schaa@googlemail.com>
 L:	linux-wireless@vger.kernel.org
 L:	users@rt2x00.serialmonkey.com (moderated for non-subscribers)
@@ -7293,7 +7297,7 @@ F:	Documentation/blockdev/ramdisk.txt
 F:	drivers/block/brd.c
 
 RANDOM NUMBER DRIVER
-M:	Theodore Ts'o" <tytso@mit.edu>
+M:	"Theodore Ts'o" <tytso@mit.edu>
 S:	Maintained
 F:	drivers/char/random.c
 
@@ -7674,7 +7678,6 @@ F:	drivers/clk/samsung/
 SAMSUNG SXGBE DRIVERS
 M:	Byungho An <bh74.an@samsung.com>
 M:	Girish K S <ks.giri@samsung.com>
-M:	Siva Reddy Kallam <siva.kallam@samsung.com>
 M:	Vipul Pandya <vipul.pandya@samsung.com>
 S:	Supported
 L:	netdev@vger.kernel.org
@@ -9952,7 +9955,7 @@ F:	drivers/net/hamradio/*scc.c
 F:	drivers/net/hamradio/z8530.h
 
 ZBUD COMPRESSED PAGE ALLOCATOR
-M:	Seth Jennings <sjenning@linux.vnet.ibm.com>
+M:	Seth Jennings <sjennings@variantweb.net>
 L:	linux-mm@kvack.org
 S:	Maintained
 F:	mm/zbud.c
@@ -9997,7 +10000,7 @@ F:	mm/zsmalloc.c
 F:	include/linux/zsmalloc.h
 
 ZSWAP COMPRESSED SWAP CACHING
-M:	Seth Jennings <sjenning@linux.vnet.ibm.com>
+M:	Seth Jennings <sjennings@variantweb.net>
 L:	linux-mm@kvack.org
 S:	Maintained
 F:	mm/zswap.c

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 15
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc5
 NAME = Shuffling Zombie Juror
 
 # *DOCUMENTATION*

arch/arc/kernel/entry.S

@@ -614,11 +614,13 @@ resume_user_mode_begin:
 
 resume_kernel_mode:
 
-#ifdef CONFIG_PREEMPT
-
-	; This is a must for preempt_schedule_irq()
+	; Disable Interrupts from this point on
+	; CONFIG_PREEMPT: This is a must for preempt_schedule_irq()
+	; !CONFIG_PREEMPT: To ensure restore_regs is intr safe
 	IRQ_DISABLE	r9
 
+#ifdef CONFIG_PREEMPT
+
 	; Can't preempt if preemption disabled
 	GET_CURR_THR_INFO_FROM_SP   r10
 	ld  r8, [r10, THREAD_INFO_PREEMPT_COUNT]

arch/arm/Kconfig

@@ -30,9 +30,9 @@ config ARM
 	select HAVE_ARCH_SECCOMP_FILTER if (AEABI && !OABI_COMPAT)
 	select HAVE_ARCH_TRACEHOOK
 	select HAVE_BPF_JIT
+	select HAVE_CC_STACKPROTECTOR
 	select HAVE_CONTEXT_TRACKING
 	select HAVE_C_RECORDMCOUNT
-	select HAVE_CC_STACKPROTECTOR
 	select HAVE_DEBUG_KMEMLEAK
 	select HAVE_DMA_API_DEBUG
 	select HAVE_DMA_ATTRS
@@ -311,6 +311,7 @@ config ARCH_MULTIPLATFORM
 	select ARM_HAS_SG_CHAIN
 	select ARM_PATCH_PHYS_VIRT
 	select AUTO_ZRELADDR
+	select CLKSRC_OF
 	select COMMON_CLK
 	select GENERIC_CLOCKEVENTS
 	select MULTI_IRQ_HANDLER
@@ -422,8 +423,8 @@ config ARCH_EFM32
 	bool "Energy Micro efm32"
 	depends on !MMU
 	select ARCH_REQUIRE_GPIOLIB
-	select AUTO_ZRELADDR
 	select ARM_NVIC
+	select AUTO_ZRELADDR
 	select CLKSRC_OF
 	select COMMON_CLK
 	select CPU_V7M
@@ -511,8 +512,8 @@ config ARCH_IXP4XX
 	bool "IXP4xx-based"
 	depends on MMU
 	select ARCH_HAS_DMA_SET_COHERENT_MASK
-	select ARCH_SUPPORTS_BIG_ENDIAN
 	select ARCH_REQUIRE_GPIOLIB
+	select ARCH_SUPPORTS_BIG_ENDIAN
 	select CLKSRC_MMIO
 	select CPU_XSCALE
 	select DMABOUNCE if PCI
@@ -1110,9 +1111,9 @@ config ARM_NR_BANKS
 	default 8
 
 config IWMMXT
-	bool "Enable iWMMXt support" if !CPU_PJ4
-	depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4
-	default y if PXA27x || PXA3xx || ARCH_MMP || CPU_PJ4
+	bool "Enable iWMMXt support"
+	depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4 || CPU_PJ4B
+	default y if PXA27x || PXA3xx || ARCH_MMP || CPU_PJ4 || CPU_PJ4B
 	help
 	  Enable support for iWMMXt context switching at run time if
 	  running on a CPU that supports it.
@@ -1575,8 +1576,8 @@ config BIG_LITTLE
 config BL_SWITCHER
 	bool "big.LITTLE switcher support"
 	depends on BIG_LITTLE && MCPM && HOTPLUG_CPU
-	select CPU_PM
 	select ARM_CPU_SUSPEND
+	select CPU_PM
 	help
 	  The big.LITTLE "switcher" provides the core functionality to
 	  transparently handle transition between a cluster of A15's
@@ -1920,9 +1921,9 @@ config XEN
 	depends on CPU_V7 && !CPU_V6
 	depends on !GENERIC_ATOMIC64
 	depends on MMU
+	select ARCH_DMA_ADDR_T_64BIT
 	select ARM_PSCI
 	select SWIOTLB_XEN
-	select ARCH_DMA_ADDR_T_64BIT
 	help
 	  Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
 

arch/arm/Kconfig.debug

@@ -1030,9 +1030,9 @@ config DEBUG_UART_PHYS
 	default 0x40100000 if DEBUG_PXA_UART1
 	default 0x42000000 if ARCH_GEMINI
 	default 0x7c0003f8 if FOOTBRIDGE
-	default 0x80230000 if DEBUG_PICOXCELL_UART
 	default 0x80070000 if DEBUG_IMX23_UART
 	default 0x80074000 if DEBUG_IMX28_UART
+	default 0x80230000 if DEBUG_PICOXCELL_UART
 	default 0x808c0000 if ARCH_EP93XX
 	default 0x90020000 if DEBUG_NSPIRE_CLASSIC_UART || DEBUG_NSPIRE_CX_UART
 	default 0xb0090000 if DEBUG_VEXPRESS_UART0_CRX
@@ -1096,22 +1096,22 @@ config DEBUG_UART_VIRT
 	default 0xfeb26000 if DEBUG_RK3X_UART1
 	default 0xfeb30c00 if DEBUG_KEYSTONE_UART0
 	default 0xfeb31000 if DEBUG_KEYSTONE_UART1
-	default 0xfec12000 if DEBUG_MVEBU_UART || DEBUG_MVEBU_UART_ALTERNATE
-	default 0xfed60000 if DEBUG_RK29_UART0
-	default 0xfed64000 if DEBUG_RK29_UART1 || DEBUG_RK3X_UART2
-	default 0xfed68000 if DEBUG_RK29_UART2 || DEBUG_RK3X_UART3
 	default 0xfec02000 if DEBUG_SOCFPGA_UART
+	default 0xfec12000 if DEBUG_MVEBU_UART || DEBUG_MVEBU_UART_ALTERNATE
 	default 0xfec20000 if DEBUG_DAVINCI_DMx_UART0
 	default 0xfed0c000 if DEBUG_DAVINCI_DA8XX_UART1
 	default 0xfed0d000 if DEBUG_DAVINCI_DA8XX_UART2
 	default 0xfed12000 if ARCH_KIRKWOOD
+	default 0xfed60000 if DEBUG_RK29_UART0
+	default 0xfed64000 if DEBUG_RK29_UART1 || DEBUG_RK3X_UART2
+	default 0xfed68000 if DEBUG_RK29_UART2 || DEBUG_RK3X_UART3
 	default 0xfedc0000 if ARCH_EP93XX
 	default 0xfee003f8 if FOOTBRIDGE
 	default 0xfee20000 if DEBUG_NSPIRE_CLASSIC_UART || DEBUG_NSPIRE_CX_UART
-	default 0xfef36000 if DEBUG_HIGHBANK_UART
 	default 0xfee82340 if ARCH_IOP13XX
 	default 0xfef00000 if ARCH_IXP4XX && !CPU_BIG_ENDIAN
 	default 0xfef00003 if ARCH_IXP4XX && CPU_BIG_ENDIAN
+	default 0xfef36000 if DEBUG_HIGHBANK_UART
 	default 0xfefff700 if ARCH_IOP33X
 	default 0xff003000 if DEBUG_U300_UART
 	default DEBUG_UART_PHYS if !MMU

arch/arm/boot/dts/Makefile

@@ -51,10 +51,9 @@ dtb-$(CONFIG_ARCH_AT91)	+= sama5d36ek.dtb
 
 dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
+dtb-$(CONFIG_ARCH_BCM_5301X) += bcm4708-netgear-r6250.dtb
 dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm28155-ap.dtb \
 	bcm21664-garnet.dtb
-dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
-dtb-$(CONFIG_ARCH_BCM_5301X) += bcm4708-netgear-r6250.dtb
 dtb-$(CONFIG_ARCH_BERLIN) += \
 	berlin2-sony-nsz-gs7.dtb	\
 	berlin2cd-google-chromecast.dtb
@@ -246,6 +245,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
+	omap3-beagle-xm-ab.dtb \
 	omap3-evm.dtb \
 	omap3-evm-37xx.dtb \
 	omap3-ldp.dtb \
@@ -294,13 +294,6 @@ dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
 dtb-$(CONFIG_ARCH_QCOM) += qcom-msm8660-surf.dtb \
 	qcom-msm8960-cdp.dtb \
 	qcom-apq8074-dragonboard.dtb
-dtb-$(CONFIG_ARCH_U8500) += ste-snowball.dtb \
-	ste-hrefprev60-stuib.dtb \
-	ste-hrefprev60-tvk.dtb \
-	ste-hrefv60plus-stuib.dtb \
-	ste-hrefv60plus-tvk.dtb \
-	ste-ccu8540.dtb \
-	ste-ccu9540.dtb
 dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb
 dtb-$(CONFIG_ARCH_S3C64XX) += s3c6410-mini6410.dtb \
 	s3c6410-smdk6410.dtb
@@ -369,9 +362,16 @@ dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra30-cardhu-a04.dtb \
 	tegra114-dalmore.dtb \
 	tegra124-venice2.dtb
+dtb-$(CONFIG_ARCH_U300) += ste-u300.dtb
+dtb-$(CONFIG_ARCH_U8500) += ste-snowball.dtb \
+	ste-hrefprev60-stuib.dtb \
+	ste-hrefprev60-tvk.dtb \
+	ste-hrefv60plus-stuib.dtb \
+	ste-hrefv60plus-tvk.dtb \
+	ste-ccu8540.dtb \
+	ste-ccu9540.dtb
 dtb-$(CONFIG_ARCH_VERSATILE) += versatile-ab.dtb \
 	versatile-pb.dtb
-dtb-$(CONFIG_ARCH_U300) += ste-u300.dtb
 dtb-$(CONFIG_ARCH_VEXPRESS) += vexpress-v2p-ca5s.dtb \
 	vexpress-v2p-ca9.dtb \
 	vexpress-v2p-ca15-tc1.dtb \

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -183,7 +183,7 @@
 &usb {
 	status = "okay";
 
-	control@44e10000 {
+	control@44e10620 {
 		status = "okay";
 	};
 
@@ -204,7 +204,7 @@
 		dr_mode = "host";
 	};
 
-	dma-controller@07402000  {
+	dma-controller@47402000  {
 		status = "okay";
 	};
 };

arch/arm/boot/dts/am335x-evm.dts

@@ -301,8 +301,8 @@
 
 	am335x_evm_audio_pins: am335x_evm_audio_pins {
 		pinctrl-single,pins = <
-			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */
-			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
 			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
 			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
 		>;
@@ -331,7 +331,7 @@
 &usb {
 	status = "okay";
 
-	control@44e10000 {
+	control@44e10620 {
 		status = "okay";
 	};
 
@@ -352,7 +352,7 @@
 		dr_mode = "host";
 	};
 
-	dma-controller@07402000  {
+	dma-controller@47402000  {
 		status = "okay";
 	};
 };

arch/arm/boot/dts/am335x-evmsk.dts

@@ -364,7 +364,7 @@
 &usb {
 	status = "okay";
 
-	control@44e10000 {
+	control@44e10620 {
 		status = "okay";
 	};
 
@@ -385,7 +385,7 @@
 		dr_mode = "host";
 	};
 
-	dma-controller@07402000  {
+	dma-controller@47402000  {
 		status = "okay";
 	};
 };

arch/arm/boot/dts/am335x-igep0033.dtsi

@@ -118,7 +118,6 @@
 		reg = <0 0 0>; /* CS0, offset 0 */
 		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
-		gpmc,device-nand = "true";
 		gpmc,device-width = <1>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
@@ -202,7 +201,7 @@
 &usb {
 	status = "okay";
 
-	control@44e10000 {
+	control@44e10620 {
 		status = "okay";
 	};
 
@@ -223,7 +222,7 @@
 		dr_mode = "host";
 	};
 
-	dma-controller@07402000  {
+	dma-controller@47402000  {
 		status = "okay";
 	};
 };

arch/arm/boot/dts/am33xx.dtsi

@@ -72,7 +72,7 @@
 	};
 
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -94,8 +94,8 @@
 
 	/*
 	 * XXX: Use a flat representation of the AM33XX interconnect.
-	 * The real AM33XX interconnect network is quite complex.Since
-	 * that will not bring real advantage to represent that in DT
+	 * The real AM33XX interconnect network is quite complex. Since
+	 * it will not bring real advantage to represent that in DT
 	 * for the moment, just use a fake OCP bus entry to represent
 	 * the whole bus hierarchy.
 	 */
@@ -802,7 +802,7 @@
 			      <0x46000000 0x400000>;
 			reg-names = "mpu", "dat";
 			interrupts = <80>, <81>;
-			interrupts-names = "tx", "rx";
+			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 8>,
 				<&edma 9>;
@@ -816,7 +816,7 @@
 			      <0x46400000 0x400000>;
 			reg-names = "mpu", "dat";
 			interrupts = <82>, <83>;
-			interrupts-names = "tx", "rx";
+			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 10>,
 				<&edma 11>;

arch/arm/boot/dts/am4372.dtsi

@@ -691,7 +691,7 @@
 			      <0x46000000 0x400000>;
 			reg-names = "mpu", "dat";
 			interrupts = <80>, <81>;
-			interrupts-names = "tx", "rx";
+			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 8>,
 			       <&edma 9>;
@@ -705,7 +705,7 @@
 			      <0x46400000 0x400000>;
 			reg-names = "mpu", "dat";
 			interrupts = <82>, <83>;
-			interrupts-names = "tx", "rx";
+			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 10>,
 			       <&edma 11>;

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -230,6 +230,7 @@
 				#size-cells = <0>;
 				compatible = "marvell,orion-mdio";
 				reg = <0x72004 0x4>;
+				clocks = <&gateclk 4>;
 			};
 
 			eth1: ethernet@74000 {

arch/arm/boot/dts/armada-38x.dtsi

@@ -336,6 +336,7 @@
 				#size-cells = <0>;
 				compatible = "marvell,orion-mdio";
 				reg = <0x72004 0x4>;
+				clocks = <&gateclk 4>;
 			};
 
 			coredivclk: clock@e4250 {

arch/arm/boot/dts/dra7.dtsi

@@ -80,7 +80,7 @@
 	};
 
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -94,7 +94,7 @@
 	/*
 	 * XXX: Use a flat representation of the SOC interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 * Since that will not bring real advantage to represent that in DT for
+	 * Since it will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */

arch/arm/boot/dts/dra7xx-clocks.dtsi

@@ -1640,7 +1640,7 @@
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
 		clocks = <&abe_24m_fclk>, <&abe_sys_clk_div>, <&func_24m_clk>, <&atlclkin3_ck>, <&atl_clkin2_ck>, <&atl_clkin1_ck>, <&atl_clkin0_ck>, <&sys_clkin2>, <&ref_clkin0_ck>, <&ref_clkin1_ck>, <&ref_clkin2_ck>, <&ref_clkin3_ck>, <&mlb_clk>, <&mlbp_clk>;
-		ti,bit-shift = <28>;
+		ti,bit-shift = <24>;
 		reg = <0x1860>;
 	};
 

arch/arm/boot/dts/imx25.dtsi

@@ -56,6 +56,7 @@
 
 		osc {
 			compatible = "fsl,imx-osc", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};

arch/arm/boot/dts/imx27-apf27.dts

@@ -29,6 +29,7 @@
 
 		osc26m {
 			compatible = "fsl,imx-osc26m", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 	};

arch/arm/boot/dts/imx27.dtsi

@@ -48,6 +48,7 @@
 
 		osc26m {
 			compatible = "fsl,imx-osc26m", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <26000000>;
 		};
 	};

arch/arm/boot/dts/imx50.dtsi

@@ -53,21 +53,25 @@
 
 		ckil {
 			compatible = "fsl,imx-ckil", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
 			compatible = "fsl,imx-ckih1", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <22579200>;
 		};
 
 		ckih2 {
 			compatible = "fsl,imx-ckih2", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
 			compatible = "fsl,imx-osc", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};

arch/arm/boot/dts/imx51.dtsi

@@ -50,21 +50,25 @@
 
 		ckil {
 			compatible = "fsl,imx-ckil", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
 			compatible = "fsl,imx-ckih1", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		ckih2 {
 			compatible = "fsl,imx-ckih2", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
 			compatible = "fsl,imx-osc", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};

arch/arm/boot/dts/imx53-m53evk.dts

@@ -17,7 +17,8 @@
 	compatible = "denx,imx53-m53evk", "fsl,imx53";
 
 	memory {
-		reg = <0x70000000 0x20000000>;
+		reg = <0x70000000 0x20000000>,
+		      <0xb0000000 0x20000000>;
 	};
 
 	soc {
@@ -193,17 +194,17 @@
 		irq-trigger = <0x1>;
 
 		stmpe_touchscreen {
-			compatible = "stmpe,ts";
+			compatible = "st,stmpe-ts";
 			reg = <0>;
-			ts,sample-time = <4>;
-			ts,mod-12b = <1>;
-			ts,ref-sel = <0>;
-			ts,adc-freq = <1>;
-			ts,ave-ctrl = <3>;
-			ts,touch-det-delay = <3>;
-			ts,settling = <4>;
-			ts,fraction-z = <7>;
-			ts,i-drive = <1>;
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <3>;
+			st,touch-det-delay = <3>;
+			st,settling = <4>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
 		};
 	};
 

arch/arm/boot/dts/imx53-qsb-common.dtsi

@@ -14,7 +14,8 @@
 
 / {
 	memory {
-		reg = <0x70000000 0x40000000>;
+		reg = <0x70000000 0x20000000>,
+		      <0xb0000000 0x20000000>;
 	};
 
 	display0: display@di0 {

arch/arm/boot/dts/imx53-tx53-x03x.dts

@@ -25,12 +25,17 @@
 	soc {
 		display: display@di0 {
 			compatible = "fsl,imx-parallel-display";
-			crtcs = <&ipu 0>;
 			interface-pix-fmt = "rgb24";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_rgb24_vga1>;
 			status = "okay";
 
+			port {
+				display0_in: endpoint {
+					remote-endpoint = <&ipu_di0_disp0>;
+				};
+			};
+
 			display-timings {
 				VGA {
 					clock-frequency = <25200000>;
@@ -293,6 +298,10 @@
 	};
 };
 
+&ipu_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
 &kpp {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_kpp>;

arch/arm/boot/dts/imx53.dtsi

@@ -70,21 +70,25 @@
 
 		ckil {
 			compatible = "fsl,imx-ckil", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
 			compatible = "fsl,imx-ckih1", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <22579200>;
 		};
 
 		ckih2 {
 			compatible = "fsl,imx-ckih2", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
 			compatible = "fsl,imx-osc", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};
@@ -430,7 +434,7 @@
 
 					port {
 						lvds1_in: endpoint {
-							remote-endpoint = <&ipu_di0_lvds0>;
+							remote-endpoint = <&ipu_di1_lvds1>;
 						};
 					};
 				};

arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts

@@ -19,7 +19,10 @@
 	compatible = "dmo,imx6q-edmqmx6", "fsl,imx6q";
 
 	aliases {
-		gpio7 = &stmpe_gpio;
+		gpio7 = &stmpe_gpio1;
+		gpio8 = &stmpe_gpio2;
+		stmpe-i2c0 = &stmpe1;
+		stmpe-i2c1 = &stmpe2;
 	};
 
 	memory {
@@ -40,13 +43,15 @@
 			regulator-always-on;
 		};
 
-		reg_usb_otg_vbus: regulator@1 {
+		reg_usb_otg_switch: regulator@1 {
 			compatible = "regulator-fixed";
 			reg = <1>;
-			regulator-name = "usb_otg_vbus";
+			regulator-name = "usb_otg_switch";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio7 12 0>;
+			regulator-boot-on;
+			regulator-always-on;
 		};
 
 		reg_usb_host1: regulator@2 {
@@ -65,23 +70,23 @@
 
 		led-blue {
 			label = "blue";
-			gpios = <&stmpe_gpio 8 GPIO_ACTIVE_HIGH>;
+			gpios = <&stmpe_gpio1 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		led-green {
 			label = "green";
-			gpios = <&stmpe_gpio 9 GPIO_ACTIVE_HIGH>;
+			gpios = <&stmpe_gpio1 9 GPIO_ACTIVE_HIGH>;
 		};
 
 		led-pink {
 			label = "pink";
-			gpios = <&stmpe_gpio 10 GPIO_ACTIVE_HIGH>;
+			gpios = <&stmpe_gpio1 10 GPIO_ACTIVE_HIGH>;
 		};
 
 		led-red {
 			label = "red";
-			gpios = <&stmpe_gpio 11 GPIO_ACTIVE_HIGH>;
+			gpios = <&stmpe_gpio1 11 GPIO_ACTIVE_HIGH>;
 		};
 	};
 };
@@ -99,7 +104,8 @@
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2
-		     &pinctrl_stmpe>;
+		     &pinctrl_stmpe1
+		     &pinctrl_stmpe2>;
 	status = "okay";
 
 	pmic: pfuze100@08 {
@@ -205,13 +211,25 @@
 		};
 	};
 
-	stmpe: stmpe1601@40 {
+	stmpe1: stmpe1601@40 {
 		compatible = "st,stmpe1601";
 		reg = <0x40>;
 		interrupts = <30 0>;
 		interrupt-parent = <&gpio3>;
 
-		stmpe_gpio: stmpe_gpio {
+		stmpe_gpio1: stmpe_gpio {
+			#gpio-cells = <2>;
+			compatible = "st,stmpe-gpio";
+		};
+	};
+
+	stmpe2: stmpe1601@44 {
+		compatible = "st,stmpe1601";
+		reg = <0x44>;
+		interrupts = <2 0>;
+		interrupt-parent = <&gpio5>;
+
+		stmpe_gpio2: stmpe_gpio {
 			#gpio-cells = <2>;
 			compatible = "st,stmpe-gpio";
 		};
@@ -273,10 +291,14 @@
 			>;
 		};
 
-		pinctrl_stmpe: stmpegrp {
+		pinctrl_stmpe1: stmpe1grp {
 			fsl,pins = <MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x80000000>;
 		};
 
+		pinctrl_stmpe2: stmpe2grp {
+			fsl,pins = <MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x80000000>;
+		};
+
 		pinctrl_uart1: uart1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
@@ -293,7 +315,7 @@
 
 		pinctrl_usbotg: usbotggrp {
 			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
 			>;
 		};
 
@@ -344,11 +366,11 @@
 &usbh1 {
 	vbus-supply = <&reg_usb_host1>;
 	disable-over-current;
+	dr_mode = "host";
 	status = "okay";
 };
 
 &usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg>;
 	disable-over-current;

arch/arm/boot/dts/imx6q-gw5400-a.dts

@@ -487,9 +487,6 @@
 
 &ldb {
 	status = "okay";
-	lvds-channel@0 {
-		crtcs = <&ipu1 0>, <&ipu1 1>, <&ipu2 0>, <&ipu2 1>;
-	};
 };
 
 &pcie {

arch/arm/boot/dts/imx6qdl-gw52xx.dtsi

@@ -436,9 +436,6 @@
 
 &ldb {
 	status = "okay";
-	lvds-channel@0 {
-		crtcs = <&ipu1 0>, <&ipu1 1>;
-	};
 };
 
 &pcie {

arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi

@@ -26,25 +26,25 @@
 				/* GPIO16 -> AR8035 25MHz */
 				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0xc0000000
 				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x80000000
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
 				/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
 				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1
 				/* AR8035 pin strapping: IO voltage: pull up */
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
 				/* AR8035 pin strapping: PHYADDR#0: pull down */
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x130b0
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030
 				/* AR8035 pin strapping: PHYADDR#1: pull down */
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x130b0
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030
 				/* AR8035 pin strapping: MODE#1: pull up */
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
 				/* AR8035 pin strapping: MODE#3: pull up */
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
 				/* AR8035 pin strapping: MODE#0: pull down */
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x130b0
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x13030
 
 				/*
 				 * As the RMII pins are also connected to RGMII

arch/arm/boot/dts/imx6qdl.dtsi

@@ -10,6 +10,8 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
 #include "skeleton.dtsi"
 
 / {
@@ -46,8 +48,6 @@
 	intc: interrupt-controller@00a01000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 		interrupt-controller;
 		reg = <0x00a01000 0x1000>,
 		      <0x00a00100 0x100>;
@@ -59,16 +59,19 @@
 
 		ckil {
 			compatible = "fsl,imx-ckil", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
 			compatible = "fsl,imx-ckih1", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
 			compatible = "fsl,imx-osc", "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};
@@ -138,6 +141,12 @@
 				  0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
 			interrupts = <0 123 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+			                <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+			                <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+			                <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>;
 			clock-names = "pcie_ref_125m", "sata_ref_100m", "lvds_gate", "pcie_axi";
 			status = "disabled";

arch/arm/boot/dts/imx6sl-evk.dts

@@ -282,6 +282,7 @@
 				MX6SL_PAD_ECSPI1_MISO__ECSPI1_MISO	0x100b1
 				MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI	0x100b1
 				MX6SL_PAD_ECSPI1_SCLK__ECSPI1_SCLK	0x100b1
+				MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11	0x80000000
 			>;
 		};
 

arch/arm/boot/dts/imx6sl.dtsi

@@ -68,8 +68,6 @@
 	intc: interrupt-controller@00a01000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 		interrupt-controller;
 		reg = <0x00a01000 0x1000>,
 		      <0x00a00100 0x100>;
@@ -81,11 +79,13 @@
 
 		ckil {
 			compatible = "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		osc {
 			compatible = "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};

arch/arm/boot/dts/kirkwood-b3.dts

@@ -75,7 +75,7 @@
 			m25p16@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "m25p16";
+				compatible = "st,m25p16";
 				reg = <0>;
 				spi-max-frequency = <40000000>;
 				mode = <0>;

arch/arm/boot/dts/kirkwood-cloudbox.dts

@@ -46,7 +46,7 @@
 			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "mx25l4005a";
+				compatible = "mxicy,mx25l4005a";
 				reg = <0>;
 				spi-max-frequency = <20000000>;
 				mode = <0>;

arch/arm/boot/dts/kirkwood-dreamplug.dts

@@ -43,7 +43,7 @@
 			m25p40@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "mx25l1606e";
+				compatible = "mxicy,mx25l1606e";
 				reg = <0>;
 				spi-max-frequency = <50000000>;
 				mode = <0>;

arch/arm/boot/dts/kirkwood-laplug.dts

@@ -48,7 +48,7 @@
 			status = "okay";
 
 			eeprom@50 {
-				compatible = "at,24c04";
+				compatible = "atmel,24c04";
 				pagesize = <16>;
 				reg = <0x50>;
 			};

arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts

@@ -56,7 +56,7 @@
 			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "mx25l12805d";
+				compatible = "mxicy,mx25l12805d";
 				reg = <0>;
 				spi-max-frequency = <50000000>;
 				mode = <0>;

arch/arm/boot/dts/kirkwood-ns2-common.dtsi

@@ -32,7 +32,7 @@
 			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "mx25l4005a";
+				compatible = "mxicy,mx25l4005a";
 				reg = <0>;
 				spi-max-frequency = <20000000>;
 				mode = <0>;
@@ -50,7 +50,7 @@
 			status = "okay";
 
 			eeprom@50 {
-				compatible = "at,24c04";
+				compatible = "atmel,24c04";
 				pagesize = <16>;
 				reg = <0x50>;
 			};

arch/arm/boot/dts/kirkwood-nsa310.dts

@@ -104,7 +104,7 @@
 			status = "okay";
 
 			adt7476: adt7476a@2e {
-				compatible = "adt7476";
+				compatible = "adi,adt7476";
 				reg = <0x2e>;
 			};
 		};

arch/arm/boot/dts/kirkwood-nsa310a.dts

@@ -94,7 +94,7 @@
 			status = "okay";
 
 			lm85: lm85@2e {
-				compatible = "lm85";
+				compatible = "national,lm85";
 				reg = <0x2e>;
 			};
 		};

arch/arm/boot/dts/kirkwood-openblocks_a6.dts

@@ -40,7 +40,7 @@
 			pinctrl-names = "default";
 
 			s35390a: s35390a@30 {
-				compatible = "s35390a";
+				compatible = "sii,s35390a";
 				reg = <0x30>;
 			};
 		};

arch/arm/boot/dts/kirkwood-openblocks_a7.dts

@@ -52,7 +52,7 @@
 			pinctrl-names = "default";
 
 			s24c02: s24c02@50 {
-				compatible = "24c02";
+				compatible = "atmel,24c02";
 				reg = <0x50>;
 			};
 		};

arch/arm/boot/dts/omap3-beagle-xm-ab.dts

@@ -0,0 +1,16 @@
+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "omap3-beagle-xm.dts"
+
+/ {
+	/* HS USB Port 2 Power enable was inverted with the xM C */
+	hsusb2_power: hsusb2_power_reg {
+		enable-active-high;
+	};
+};

arch/arm/boot/dts/omap3-devkit8000.dts

@@ -112,7 +112,6 @@
 		reg = <0 0 0>; /* CS0, offset 0 */
 		nand-bus-width = <16>;
 
-		gpmc,device-nand;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <44>;

arch/arm/boot/dts/omap3-lilly-a83x.dtsi

@@ -368,7 +368,6 @@
 		/* no elm on omap3 */
 
 		gpmc,mux-add-data = <0>;
-		gpmc,device-nand;
 		gpmc,device-width = <2>;
 		gpmc,wait-pin = <0>;
 		gpmc,wait-monitoring-ns = <0>;

arch/arm/boot/dts/omap3.dtsi

@@ -74,7 +74,7 @@
 	/*
 	 * XXX: Use a flat representation of the OMAP3 interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 * Since that will not bring real advantage to represent that in DT for
+	 * Since it will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */

arch/arm/boot/dts/omap4.dtsi

@@ -72,7 +72,7 @@
 	};
 
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -96,7 +96,7 @@
 	/*
 	 * XXX: Use a flat representation of the OMAP4 interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 * Since that will not bring real advantage to represent that in DT for
+	 * Since it will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */

arch/arm/boot/dts/omap5.dtsi

@@ -93,7 +93,7 @@
 	};
 
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -107,7 +107,7 @@
 	/*
 	 * XXX: Use a flat representation of the OMAP3 interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 * Since that will not bring real advantage to represent that in DT for
+	 * Since it will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */
@@ -813,6 +813,12 @@
 				      <0x4a084c00 0x40>;
 				reg-names = "phy_rx", "phy_tx", "pll_ctrl";
 				ctrl-module = <&omap_control_usb3phy>;
+				clocks = <&usb_phy_cm_clk32k>,
+					 <&sys_clkin>,
+					 <&usb_otg_ss_refclk960m>;
+				clock-names =	"wkupclk",
+						"sysclk",
+						"refclk";
 				#phy-cells = <0>;
 			};
 		};

arch/arm/boot/dts/r8a7740.dtsi

@@ -28,7 +28,6 @@
 	gic: interrupt-controller@c2800000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
-		#address-cells = <1>;
 		interrupt-controller;
 		reg = <0xc2800000 0x1000>,
 		      <0xc2000000 0x1000>;

arch/arm/boot/dts/r8a7790-lager.dts

@@ -141,12 +141,12 @@
 	};
 
 	sdhi0_pins: sd0 {
-		renesas,gpios = "sdhi0_data4", "sdhi0_ctrl";
+		renesas,groups = "sdhi0_data4", "sdhi0_ctrl";
 		renesas,function = "sdhi0";
 	};
 
 	sdhi2_pins: sd2 {
-		renesas,gpios = "sdhi2_data4", "sdhi2_ctrl";
+		renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
 		renesas,function = "sdhi2";
 	};
 

arch/arm/boot/dts/r8a7790.dtsi

@@ -673,7 +673,7 @@
 			renesas,clock-indices = <
 				R8A7790_CLK_TMU1 R8A7790_CLK_TMU3 R8A7790_CLK_TMU2
 				R8A7790_CLK_CMT0 R8A7790_CLK_TMU0 R8A7790_CLK_VSP1_DU1
-				R8A7790_CLK_VSP1_DU0 R8A7790_CLK_VSP1_RT R8A7790_CLK_VSP1_SY
+				R8A7790_CLK_VSP1_DU0 R8A7790_CLK_VSP1_R R8A7790_CLK_VSP1_S
 			>;
 			clock-output-names =
 				"tmu1", "tmu3", "tmu2", "cmt0", "tmu0", "vsp1-du1",

arch/arm/boot/dts/r8a7791-koelsch.dts

@@ -230,17 +230,17 @@
 	};
 
 	sdhi0_pins: sd0 {
-		renesas,gpios = "sdhi0_data4", "sdhi0_ctrl";
+		renesas,groups = "sdhi0_data4", "sdhi0_ctrl";
 		renesas,function = "sdhi0";
 	};
 
 	sdhi1_pins: sd1 {
-		renesas,gpios = "sdhi1_data4", "sdhi1_ctrl";
+		renesas,groups = "sdhi1_data4", "sdhi1_ctrl";
 		renesas,function = "sdhi1";
 	};
 
 	sdhi2_pins: sd2 {
-		renesas,gpios = "sdhi2_data4", "sdhi2_ctrl";
+		renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
 		renesas,function = "sdhi2";
 	};
 

arch/arm/boot/dts/r8a7791.dtsi

@@ -688,7 +688,7 @@
 			renesas,clock-indices = <
 				R8A7791_CLK_TMU1 R8A7791_CLK_TMU3 R8A7791_CLK_TMU2
 				R8A7791_CLK_CMT0 R8A7791_CLK_TMU0 R8A7791_CLK_VSP1_DU1
-				R8A7791_CLK_VSP1_DU0 R8A7791_CLK_VSP1_SY
+				R8A7791_CLK_VSP1_DU0 R8A7791_CLK_VSP1_S
 			>;
 			clock-output-names =
 				"tmu1", "tmu3", "tmu2", "cmt0", "tmu0", "vsp1-du1",

arch/arm/boot/dts/rk3188.dtsi

@@ -149,7 +149,7 @@
 
 			uart0 {
 				uart0_xfer: uart0-xfer {
-					rockchip,pins = <RK_GPIO1 0 RK_FUNC_1 &pcfg_pull_none>,
+					rockchip,pins = <RK_GPIO1 0 RK_FUNC_1 &pcfg_pull_up>,
 							<RK_GPIO1 1 RK_FUNC_1 &pcfg_pull_none>;
 				};
 
@@ -164,7 +164,7 @@
 
 			uart1 {
 				uart1_xfer: uart1-xfer {
-					rockchip,pins = <RK_GPIO1 4 RK_FUNC_1 &pcfg_pull_none>,
+					rockchip,pins = <RK_GPIO1 4 RK_FUNC_1 &pcfg_pull_up>,
 							<RK_GPIO1 5 RK_FUNC_1 &pcfg_pull_none>;
 				};
 
@@ -179,7 +179,7 @@
 
 			uart2 {
 				uart2_xfer: uart2-xfer {
-					rockchip,pins = <RK_GPIO1 8 RK_FUNC_1 &pcfg_pull_none>,
+					rockchip,pins = <RK_GPIO1 8 RK_FUNC_1 &pcfg_pull_up>,
 							<RK_GPIO1 9 RK_FUNC_1 &pcfg_pull_none>;
 				};
 				/* no rts / cts for uart2 */
@@ -187,7 +187,7 @@
 
 			uart3 {
 				uart3_xfer: uart3-xfer {
-					rockchip,pins = <RK_GPIO1 10 RK_FUNC_1 &pcfg_pull_none>,
+					rockchip,pins = <RK_GPIO1 10 RK_FUNC_1 &pcfg_pull_up>,
 							<RK_GPIO1 11 RK_FUNC_1 &pcfg_pull_none>;
 				};
 

arch/arm/boot/dts/sh73a0.dtsi

@@ -34,7 +34,6 @@
 	gic: interrupt-controller@f0001000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
-		#address-cells = <1>;
 		interrupt-controller;
 		reg = <0xf0001000 0x1000>,
 		      <0xf0000100 0x100>;

arch/arm/boot/dts/stih415-pinctrl.dtsi

@@ -49,7 +49,7 @@
 			reg 		= <0xfe61f080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges 		= <0 0xfe610000 0x5000>;
 
 			PIO0: gpio@fe610000 {
@@ -187,7 +187,7 @@
 			reg 		= <0xfee0f080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges		= <0 0xfee00000 0x8000>;
 
 			PIO5: gpio@fee00000 {
@@ -282,7 +282,7 @@
 			reg 		= <0xfe82f080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges		= <0 0xfe820000 0x8000>;
 
 			PIO13: gpio@fe820000 {
@@ -423,7 +423,7 @@
 			reg 		= <0xfd6bf080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges		= <0 0xfd6b0000 0x3000>;
 
 			PIO100: gpio@fd6b0000 {
@@ -460,7 +460,7 @@
 			reg 		= <0xfd33f080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges		= <0 0xfd330000 0x5000>;
 
 			PIO103: gpio@fd330000 {

arch/arm/boot/dts/stih416-pinctrl.dtsi

@@ -53,7 +53,7 @@
 			reg 		= <0xfe61f080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges		= <0 0xfe610000 0x6000>;
 
 			PIO0: gpio@fe610000 {
@@ -201,7 +201,7 @@
 			reg 		= <0xfee0f080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges		= <0 0xfee00000 0x10000>;
 
 			PIO5: gpio@fee00000 {
@@ -333,7 +333,7 @@
 			reg 		= <0xfe82f080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges 		= <0 0xfe820000 0x6000>;
 
 			PIO13: gpio@fe820000 {
@@ -461,7 +461,7 @@
 			reg 		= <0xfd6bf080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges		= <0 0xfd6b0000 0x3000>;
 
 			PIO100: gpio@fd6b0000 {
@@ -498,7 +498,7 @@
 			reg 		= <0xfd33f080 0x4>;
 			reg-names	= "irqmux";
 			interrupts 	= <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts-names = "irqmux";
+			interrupt-names	= "irqmux";
 			ranges			= <0 0xfd330000 0x5000>;
 
 			PIO103: gpio@fd330000 {

arch/arm/boot/dts/tegra124.dtsi

@@ -233,19 +233,6 @@
 		status = "disabled";
 	};
 
-	serial@0,70006400 {
-		compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
-		reg = <0x0 0x70006400 0x0 0x40>;
-		reg-shift = <2>;
-		interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&tegra_car TEGRA124_CLK_UARTE>;
-		resets = <&tegra_car 66>;
-		reset-names = "serial";
-		dmas = <&apbdma 20>, <&apbdma 20>;
-		dma-names = "rx", "tx";
-		status = "disabled";
-	};
-
 	pwm@0,7000a000 {
 		compatible = "nvidia,tegra124-pwm", "nvidia,tegra20-pwm";
 		reg = <0x0 0x7000a000 0x0 0x100>;

arch/arm/boot/dts/vf610-twr.dts

@@ -25,11 +25,13 @@
 	clocks {
 		audio_ext {
 			compatible = "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <24576000>;
 		};
 
 		enet_ext {
 			compatible = "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <50000000>;
 		};
 	};

arch/arm/boot/dts/vf610.dtsi

@@ -45,11 +45,13 @@
 
 		sxosc {
 			compatible = "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		fxosc {
 			compatible = "fixed-clock";
+			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};
@@ -72,8 +74,6 @@
 			intc: interrupt-controller@40002000 {
 				compatible = "arm,cortex-a9-gic";
 				#interrupt-cells = <3>;
-				#address-cells = <1>;
-				#size-cells = <1>;
 				interrupt-controller;
 				reg = <0x40003000 0x1000>,
 				      <0x40002100 0x100>;

arch/arm/boot/dts/zynq-7000.dtsi

@@ -24,6 +24,7 @@
 			device_type = "cpu";
 			reg = <0>;
 			clocks = <&clkc 3>;
+			clock-latency = <1000>;
 			operating-points = <
 				/* kHz    uV */
 				666667  1000000
@@ -54,6 +55,28 @@
 		interrupt-parent = <&intc>;
 		ranges;
 
+		i2c0: zynq-i2c@e0004000 {
+			compatible = "cdns,i2c-r1p10";
+			status = "disabled";
+			clocks = <&clkc 38>;
+			interrupt-parent = <&intc>;
+			interrupts = <0 25 4>;
+			reg = <0xe0004000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: zynq-i2c@e0005000 {
+			compatible = "cdns,i2c-r1p10";
+			status = "disabled";
+			clocks = <&clkc 39>;
+			interrupt-parent = <&intc>;
+			interrupts = <0 48 4>;
+			reg = <0xe0005000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		intc: interrupt-controller@f8f01000 {
 			compatible = "arm,cortex-a9-gic";
 			#interrupt-cells = <3>;

arch/arm/boot/dts/zynq-zc702.dts

@@ -34,6 +34,82 @@
 	phy-mode = "rgmii";
 };
 
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	i2cswitch@74 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			si570: clock-generator@5d {
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				temperature-stability = <50>;
+				reg = <0x5d>;
+				factory-fout = <156250000>;
+				clock-frequency = <148500000>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@54 {
+				compatible = "at,24c08";
+				reg = <0x54>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			gpio@21 {
+				compatible = "ti,tca6416";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			rtc@51 {
+				compatible = "nxp,pcf8563";
+				reg = <0x51>;
+			};
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			hwmon@52 {
+				compatible = "ti,ucd9248";
+				reg = <52>;
+			};
+			hwmon@53 {
+				compatible = "ti,ucd9248";
+				reg = <53>;
+			};
+			hwmon@54 {
+				compatible = "ti,ucd9248";
+				reg = <54>;
+			};
+		};
+	};
+};
+
 &sdhci0 {
 	status = "okay";
 };

arch/arm/boot/dts/zynq-zc706.dts

@@ -35,6 +35,74 @@
 	phy-mode = "rgmii";
 };
 
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	i2cswitch@74 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			si570: clock-generator@5d {
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				temperature-stability = <50>;
+				reg = <0x5d>;
+				factory-fout = <156250000>;
+				clock-frequency = <148500000>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@54 {
+				compatible = "at,24c08";
+				reg = <0x54>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			gpio@21 {
+				compatible = "ti,tca6416";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			rtc@51 {
+				compatible = "nxp,pcf8563";
+				reg = <0x51>;
+			};
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			ucd90120@65 {
+				compatible = "ti,ucd90120";
+				reg = <0x65>;
+			};
+		};
+	};
+};
+
 &sdhci0 {
 	status = "okay";
 };

arch/arm/common/bL_switcher.c

@@ -797,10 +797,8 @@ static int __init bL_switcher_init(void)
 {
 	int ret;
 
-	if (MAX_NR_CLUSTERS != 2) {
-		pr_err("%s: only dual cluster systems are supported\n", __func__);
-		return -EINVAL;
-	}
+	if (!mcpm_is_available())
+		return -ENODEV;
 
 	cpu_notifier(bL_switcher_hotplug_callback, 0);
 

arch/arm/common/mcpm_entry.c

@@ -48,6 +48,11 @@ int __init mcpm_platform_register(const struct mcpm_platform_ops *ops)
 	return 0;
 }
 
+bool mcpm_is_available(void)
+{
+	return (platform_ops) ? true : false;
+}
+
 int mcpm_cpu_power_up(unsigned int cpu, unsigned int cluster)
 {
 	if (!platform_ops)

arch/arm/configs/omap2plus_defconfig

@@ -226,7 +226,7 @@ CONFIG_USB_DWC3=m
 CONFIG_USB_TEST=y
 CONFIG_NOP_USB_XCEIV=y
 CONFIG_OMAP_USB2=y
-CONFIG_OMAP_USB3=y
+CONFIG_TI_PIPE3=y
 CONFIG_AM335X_PHY_USB=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_DEBUG=y

arch/arm/configs/u300_defconfig

@@ -11,6 +11,7 @@ CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 # CONFIG_LBDAF is not set
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
 # CONFIG_IOSCHED_CFQ is not set
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_U300=y
@@ -21,7 +22,6 @@ CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="root=/dev/ram0 rw rootfstype=rootfs console=ttyAMA0,115200n8 lpj=515072"
 CONFIG_CPU_IDLE=y
-CONFIG_FPE_NWFPE=y
 # CONFIG_SUSPEND is not set
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
@@ -64,8 +64,8 @@ CONFIG_TMPFS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_FS=y
 # CONFIG_SCHED_DEBUG is not set
 CONFIG_TIMER_STATS=y
 # CONFIG_DEBUG_PREEMPT is not set
-CONFIG_DEBUG_INFO=y

arch/arm/configs/u8500_defconfig

@@ -1,16 +1,16 @@
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_ARCH_U8500=y
 CONFIG_MACH_HREFV60=y
 CONFIG_MACH_SNOWBALL=y
-CONFIG_MACH_UX500_DT=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_PREEMPT=y
@@ -34,16 +34,22 @@ CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
 CONFIG_NETFILTER=y
 CONFIG_PHONET=y
-# CONFIG_WIRELESS is not set
+CONFIG_CFG80211=y
+CONFIG_CFG80211_DEBUGFS=y
+CONFIG_MAC80211=y
+CONFIG_MAC80211_LEDS=y
 CONFIG_CAIF=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=65536
 CONFIG_SENSORS_BH1780=y
 CONFIG_NETDEVICES=y
 CONFIG_SMSC911X=y
 CONFIG_SMSC_PHY=y
-# CONFIG_WLAN is not set
+CONFIG_CW1200=y
+CONFIG_CW1200_WLAN_SDIO=y
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
 CONFIG_INPUT_EVDEV=y
 # CONFIG_KEYBOARD_ATKBD is not set
@@ -85,15 +91,12 @@ CONFIG_AB8500_USB=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_ETH=m
 CONFIG_MMC=y
-CONFIG_MMC_UNSAFE_RESUME=y
-# CONFIG_MMC_BLOCK_BOUNCE is not set
 CONFIG_MMC_ARMMMCI=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_LM3530=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_LP5521=y
-CONFIG_LEDS_TRIGGERS=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_AB8500=y
@@ -103,6 +106,11 @@ CONFIG_STE_DMA40=y
 CONFIG_STAGING=y
 CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI4=y
 CONFIG_HSEM_U8500=y
+CONFIG_IIO=y
+CONFIG_IIO_ST_ACCEL_3AXIS=y
+CONFIG_IIO_ST_GYRO_3AXIS=y
+CONFIG_IIO_ST_MAGN_3AXIS=y
+CONFIG_IIO_ST_PRESS=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
@@ -110,8 +118,6 @@ CONFIG_EXT2_FS_SECURITY=y
 CONFIG_EXT3_FS=y
 CONFIG_EXT4_FS=y
 CONFIG_VFAT_FS=y
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_TMPFS=y
 CONFIG_TMPFS_POSIX_ACL=y
 # CONFIG_MISC_FILESYSTEMS is not set

arch/arm/include/asm/cputype.h

@@ -222,22 +222,22 @@ static inline int cpu_is_xsc3(void)
 #endif
 
 /*
- * Marvell's PJ4 core is based on V7 version. It has some modification
- * for coprocessor setting. For this reason, we need a way to distinguish
- * it.
+ * Marvell's PJ4 and PJ4B cores are based on V7 version,
+ * but require a specical sequence for enabling coprocessors.
+ * For this reason, we need a way to distinguish them.
  */
-#ifndef CONFIG_CPU_PJ4
-#define cpu_is_pj4()	0
-#else
+#if defined(CONFIG_CPU_PJ4) || defined(CONFIG_CPU_PJ4B)
 static inline int cpu_is_pj4(void)
 {
 	unsigned int id;
 
 	id = read_cpuid_id();
-	if ((id & 0xfffffff0) == 0x562f5840)
+	if ((id & 0xff0fff00) == 0x560f5800)
 		return 1;
 
 	return 0;
 }
+#else
+#define cpu_is_pj4()	0
 #endif
 #endif

arch/arm/include/asm/div64.h

@@ -156,7 +156,7 @@
 		/* Select the best insn combination to perform the   */	\
 		/* actual __m * __n / (__p << 64) operation.         */	\
 		if (!__c) {						\
-			asm (	"umull	%Q0, %R0, %1, %Q2\n\t"		\
+			asm (	"umull	%Q0, %R0, %Q1, %Q2\n\t"		\
 				"mov	%Q0, #0"			\
 				: "=&r" (__res)				\
 				: "r" (__m), "r" (__n)			\

arch/arm/include/asm/mcpm.h

@@ -53,6 +53,13 @@ void mcpm_set_early_poke(unsigned cpu, unsigned cluster,
  * CPU/cluster power operations API for higher subsystems to use.
  */
 
+/**
+ * mcpm_is_available - returns whether MCPM is initialized and available
+ *
+ * This returns true or false accordingly.
+ */
+bool mcpm_is_available(void);
+
 /**
  * mcpm_cpu_power_up - make given CPU in given cluster runable
  *

arch/arm/include/asm/tlb.h

@@ -98,15 +98,25 @@ static inline void __tlb_alloc_page(struct mmu_gather *tlb)
 	}
 }
 
-static inline void tlb_flush_mmu(struct mmu_gather *tlb)
+static inline void tlb_flush_mmu_tlbonly(struct mmu_gather *tlb)
 {
 	tlb_flush(tlb);
+}
+
+static inline void tlb_flush_mmu_free(struct mmu_gather *tlb)
+{
 	free_pages_and_swap_cache(tlb->pages, tlb->nr);
 	tlb->nr = 0;
 	if (tlb->pages == tlb->local)
 		__tlb_alloc_page(tlb);
 }
 
+static inline void tlb_flush_mmu(struct mmu_gather *tlb)
+{
+	tlb_flush_mmu_tlbonly(tlb);
+	tlb_flush_mmu_free(tlb);
+}
+
 static inline void
 tlb_gather_mmu(struct mmu_gather *tlb, struct mm_struct *mm, unsigned long start, unsigned long end)
 {

arch/arm/include/uapi/asm/unistd.h

@@ -408,6 +408,7 @@
 #define __NR_finit_module		(__NR_SYSCALL_BASE+379)
 #define __NR_sched_setattr		(__NR_SYSCALL_BASE+380)
 #define __NR_sched_getattr		(__NR_SYSCALL_BASE+381)
+#define __NR_renameat2			(__NR_SYSCALL_BASE+382)
 
 /*
  * This may need to be greater than __NR_last_syscall+1 in order to

arch/arm/kernel/Makefile

@@ -79,6 +79,7 @@ obj-$(CONFIG_CPU_XSCALE)	+= xscale-cp0.o
 obj-$(CONFIG_CPU_XSC3)		+= xscale-cp0.o
 obj-$(CONFIG_CPU_MOHAWK)	+= xscale-cp0.o
 obj-$(CONFIG_CPU_PJ4)		+= pj4-cp0.o
+obj-$(CONFIG_CPU_PJ4B)		+= pj4-cp0.o
 obj-$(CONFIG_IWMMXT)		+= iwmmxt.o
 obj-$(CONFIG_PERF_EVENTS)	+= perf_regs.o
 obj-$(CONFIG_HW_PERF_EVENTS)	+= perf_event.o perf_event_cpu.o

arch/arm/kernel/calls.S

@@ -391,6 +391,7 @@
 		CALL(sys_finit_module)
 /* 380 */	CALL(sys_sched_setattr)
 		CALL(sys_sched_getattr)
+		CALL(sys_renameat2)
 #ifndef syscalls_counted
 .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
 #define syscalls_counted

arch/arm/kernel/head.S

@@ -587,7 +587,7 @@ __fixup_pv_table:
 	add	r6, r6, r3	@ adjust __pv_phys_pfn_offset address
 	add	r7, r7, r3	@ adjust __pv_offset address
 	mov	r0, r8, lsr #12	@ convert to PFN
-	str	r0, [r6, #LOW_OFFSET]	@ save computed PHYS_OFFSET to __pv_phys_pfn_offset
+	str	r0, [r6]	@ save computed PHYS_OFFSET to __pv_phys_pfn_offset
 	strcc	ip, [r7, #HIGH_OFFSET]	@ save to __pv_offset high bits
 	mov	r6, r3, lsr #24	@ constant for add/sub instructions
 	teq	r3, r6, lsl #24 @ must be 16MiB aligned

arch/arm/kernel/iwmmxt.S

@@ -19,12 +19,16 @@
 #include <asm/thread_info.h>
 #include <asm/asm-offsets.h>
 
-#if defined(CONFIG_CPU_PJ4)
+#if defined(CONFIG_CPU_PJ4) || defined(CONFIG_CPU_PJ4B)
 #define PJ4(code...)		code
 #define XSC(code...)
-#else
+#elif defined(CONFIG_CPU_MOHAWK) || \
+	defined(CONFIG_CPU_XSC3) || \
+	defined(CONFIG_CPU_XSCALE)
 #define PJ4(code...)
 #define XSC(code...)		code
+#else
+#error "Unsupported iWMMXt architecture"
 #endif
 
 #define MMX_WR0		 	(0x00)

arch/arm/kernel/machine_kexec.c

@@ -184,3 +184,10 @@ void machine_kexec(struct kimage *image)
 
 	soft_restart(reboot_entry_phys);
 }
+
+void arch_crash_save_vmcoreinfo(void)
+{
+#ifdef CONFIG_ARM_LPAE
+	VMCOREINFO_CONFIG(ARM_LPAE);
+#endif
+}

arch/arm/kernel/pj4-cp0.c

@@ -45,7 +45,7 @@ static int iwmmxt_do(struct notifier_block *self, unsigned long cmd, void *t)
 	return NOTIFY_DONE;
 }
 
-static struct notifier_block iwmmxt_notifier_block = {
+static struct notifier_block __maybe_unused iwmmxt_notifier_block = {
 	.notifier_call	= iwmmxt_do,
 };
 
@@ -72,6 +72,33 @@ static void __init pj4_cp_access_write(u32 value)
 		: "=r" (temp) : "r" (value));
 }
 
+static int __init pj4_get_iwmmxt_version(void)
+{
+	u32 cp_access, wcid;
+
+	cp_access = pj4_cp_access_read();
+	pj4_cp_access_write(cp_access | 0xf);
+
+	/* check if coprocessor 0 and 1 are available */
+	if ((pj4_cp_access_read() & 0xf) != 0xf) {
+		pj4_cp_access_write(cp_access);
+		return -ENODEV;
+	}
+
+	/* read iWMMXt coprocessor id register p1, c0 */
+	__asm__ __volatile__ ("mrc    p1, 0, %0, c0, c0, 0\n" : "=r" (wcid));
+
+	pj4_cp_access_write(cp_access);
+
+	/* iWMMXt v1 */
+	if ((wcid & 0xffffff00) == 0x56051000)
+		return 1;
+	/* iWMMXt v2 */
+	if ((wcid & 0xffffff00) == 0x56052000)
+		return 2;
+
+	return -EINVAL;
+}
 
 /*
  * Disable CP0/CP1 on boot, and let call_fpe() and the iWMMXt lazy
@@ -79,17 +106,26 @@ static void __init pj4_cp_access_write(u32 value)
  */
 static int __init pj4_cp0_init(void)
 {
-	u32 cp_access;
+	u32 __maybe_unused cp_access;
+	int vers;
 
 	if (!cpu_is_pj4())
 		return 0;
 
+	vers = pj4_get_iwmmxt_version();
+	if (vers < 0)
+		return 0;
+
+#ifndef CONFIG_IWMMXT
+	pr_info("PJ4 iWMMXt coprocessor detected, but kernel support is missing.\n");
+#else
 	cp_access = pj4_cp_access_read() & ~0xf;
 	pj4_cp_access_write(cp_access);
 
-	printk(KERN_INFO "PJ4 iWMMXt coprocessor enabled.\n");
+	pr_info("PJ4 iWMMXt v%d coprocessor enabled.\n", vers);
 	elf_hwcap |= HWCAP_IWMMXT;
 	thread_register_notifier(&iwmmxt_notifier_block);
+#endif
 
 	return 0;
 }

arch/arm/kernel/sys_oabi-compat.c

@@ -203,9 +203,9 @@ asmlinkage long sys_oabi_fcntl64(unsigned int fd, unsigned int cmd,
 	int ret;
 
 	switch (cmd) {
-	case F_GETLKP:
-	case F_SETLKP:
-	case F_SETLKPW:
+	case F_OFD_GETLK:
+	case F_OFD_SETLK:
+	case F_OFD_SETLKW:
 	case F_GETLK64:
 	case F_SETLK64:
 	case F_SETLKW64: