Merge tag 'amlogic-dt64-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt64

Pull "Amlogic 64-bit DT updates for v4.10, round 2" from Kevin Hilman:

- new SoC support: S912/GXM series (8x A53)
- new boards: Nexbox A1 (S912), Nexbox A95X (S905X)
- resets for 2nd USB PHY
- update SCPI compatible for pre-v1.0 devices

* tag 'amlogic-dt64-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
  ARM64: dts: meson-gxl: Add support for Nexbox A95X
  ARM64: dts: meson-gxm: Add support for the Nexbox A1
  ARM64: dts: Add support for Meson GXM
  ARM64: dts: meson-gxbb: add the USB reset also to the second USB PHY

Documentation/devicetree/bindings/arm/amlogic.txt

@@ -25,6 +25,10 @@ Boards with the Amlogic Meson GXL S905D SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,s905d", "amlogic,meson-gxl";
 
+Boards with the Amlogic Meson GXM S912 SoC shall have the following properties:
+  Required root node property:
+    compatible: "amlogic,s912", "amlogic,meson-gxm";
+
 Board compatible values:
   - "geniatech,atv1200" (Meson6)
   - "minix,neo-x8" (Meson8)
@@ -39,3 +43,7 @@ Board compatible values:
   - "amlogic,p212" (Meson gxl s905x)
   - "amlogic,p230" (Meson gxl s905d)
   - "amlogic,p231" (Meson gxl s905d)
+  - "amlogic,q200" (Meson gxm s912)
+  - "amlogic,q201" (Meson gxm s912)
+  - "nexbox,a95x" (Meson gxbb or Meson gxl s905x)
+  - "nexbox,a1" (Meson gxm s912)

arch/arm64/boot/dts/amlogic/Makefile

@@ -8,6 +8,10 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-nexbox-a95x.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxm-s912-q200.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxm-s912-q201.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxm-nexbox-a1.dtb
 
 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)

arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi → arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi

@@ -41,7 +41,9 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "meson-gxl-s905d.dtsi"
+/* Common DTSI for same Amlogic Q200/Q201 and P230/P231 boards using either
+ * the pin-compatible S912 (GXM) or S905D (GXL) SoCs.
+ */
 
 / {
 	aliases {

arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi

@@ -51,7 +51,7 @@
 	compatible = "amlogic,meson-gxbb";
 
 	scpi {
-		compatible = "amlogic,meson-gxbb-scpi";
+		compatible = "amlogic,meson-gxbb-scpi", "arm,scpi-pre-1.0";
 		mboxes = <&mailbox 1 &mailbox 2>;
 		shmem = <&cpu_scp_lpri &cpu_scp_hpri>;
 
@@ -87,6 +87,7 @@
 			compatible = "amlogic,meson-gxbb-usb2-phy";
 			#phy-cells = <0>;
 			reg = <0x0 0xc0000020 0x0 0x20>;
+			resets = <&reset RESET_USB_OTG>;
 			clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>;
 			clock-names = "usb_general", "usb";
 			status = "disabled";

arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts

@@ -0,0 +1,205 @@
+/*
+ * Copyright (c) 2016 Andreas Färber
+ * Copyright (c) 2016 BayLibre, Inc.
+ * Author: Neil Armstrong <narmstrong@kernel.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905x.dtsi"
+
+/ {
+	compatible = "nexbox,a95x", "amlogic,s905x", "amlogic,meson-gxl";
+	model = "NEXBOX A95X (S905X)";
+
+	aliases {
+		serial0 = &uart_AO;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	vddio_card: gpio-regulator {
+		compatible = "regulator-gpio";
+
+		regulator-name = "VDDIO_CARD";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+
+		/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
+		states = <1800000 0
+			  3300000 1>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_card>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};

arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts

@@ -43,7 +43,8 @@
 
 /dts-v1/;
 
-#include "meson-gxl-s905d-p23x.dtsi"
+#include "meson-gxl-s905d.dtsi"
+#include "meson-gx-p23x-q20x.dtsi"
 
 / {
 	compatible = "amlogic,p230", "amlogic,s905d", "amlogic,meson-gxl";

arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p231.dts

@@ -43,7 +43,8 @@
 
 /dts-v1/;
 
-#include "meson-gxl-s905d-p23x.dtsi"
+#include "meson-gxl-s905d.dtsi"
+#include "meson-gx-p23x-q20x.dtsi"
 
 / {
 	compatible = "amlogic,p231", "amlogic,s905d", "amlogic,meson-gxl";

arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts

@@ -0,0 +1,169 @@
+/*
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "meson-gxm.dtsi"
+
+/ {
+	compatible = "nexbox,a1", "amlogic,s912", "amlogic,meson-gxm";
+	model = "NEXBOX A1";
+
+	aliases {
+		serial0 = &uart_AO;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	vddio_boot: regulator-vddio-boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+};
+
+/* This UART is brought out to the DB9 connector */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+&ethmac {
+	status = "okay";
+
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+
+	/* Select external PHY by default */
+	phy-handle = <&external_phy>;
+
+	snps,reset-gpio = <&gpio GPIOZ_14 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+
+	/* External PHY is in RGMII */
+	phy-mode = "rgmii";
+};
+
+&external_mdio {
+	external_phy: ethernet-phy@0 {
+		compatible = "ethernet-phy-id001c.c916", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		max-speed = <1000>;
+	};
+};

arch/arm64/boot/dts/amlogic/meson-gxm-s912-q200.dts

@@ -0,0 +1,77 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "meson-gxm.dtsi"
+#include "meson-gx-p23x-q20x.dtsi"
+
+/ {
+	compatible = "amlogic,q200", "amlogic,s912", "amlogic,meson-gxm";
+	model = "Amlogic Meson GXM (S912) Q200 Development Board";
+};
+
+/* Q200 has exclusive choice between internal or external PHY */
+&ethmac {
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+
+	/* Select external PHY by default */
+	phy-handle = <&external_phy>;
+
+	/* External PHY reset is shared with internal PHY Led signals */
+	snps,reset-gpio = <&gpio GPIOZ_14 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+
+	/* External PHY is in RGMII */
+	phy-mode = "rgmii";
+};
+
+&external_mdio {
+	external_phy: ethernet-phy@0 {
+		compatible = "ethernet-phy-id001c.c916", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		max-speed = <1000>;
+	};
+};

arch/arm64/boot/dts/amlogic/meson-gxm-s912-q201.dts

@@ -0,0 +1,58 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "meson-gxm.dtsi"
+#include "meson-gx-p23x-q20x.dtsi"
+
+/ {
+	compatible = "amlogic,q201", "amlogic,s912", "amlogic,meson-gxm";
+	model = "Amlogic Meson GXM (S912) Q201 Development Board";
+};
+
+/* Q201 has only internal PHY port */
+&ethmac {
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};

arch/arm64/boot/dts/amlogic/meson-gxm.dtsi

@@ -0,0 +1,114 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "meson-gxl.dtsi"
+
+/ {
+	compatible = "amlogic,meson-gxm";
+
+	cpus {
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+				core1 {
+					cpu = <&cpu5>;
+				};
+				core2 {
+					cpu = <&cpu6>;
+				};
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		cpu4: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu5: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x101>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu6: cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x102>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu7: cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x103>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+	};
+};