staging: typec: fusb302: Get max snk mv/ma/mw from device-properties

This is board specific info so it should come from board config, such
as devicetree.

I've chosen to prefix these with "fcs," treating them as fusb302 driver
specific for now. We may want to revisit this and replace these with
properties which are part of a (to be written) generic type-c controller
devicetree binding.

Since this commit adds new dt-properties it also adds devicetree-bindings
documentation (which so far was absent for the fusb302 driver).

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: "Yueyao (Nathan) Zhu" <yueyao@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/devicetree/bindings/usb/fcs,fusb302.txt

@@ -0,0 +1,29 @@
+Fairchild FUSB302 Type-C Port controllers
+
+Required properties :
+- compatible             : "fcs,fusb302"
+- reg                    : I2C slave address
+- interrupts             : Interrupt specifier
+
+Optional properties :
+- fcs,max-sink-microvolt : Maximum voltage to negotiate when configured as sink
+- fcs,max-sink-microamp  : Maximum current to negotiate when configured as sink
+- fcs,max-sink-microwatt : Maximum power to negotiate when configured as sink
+			   If this is less then max-sink-microvolt *
+			   max-sink-microamp then the configured current will
+			   be clamped.
+- fcs,operating-sink-microwatt :
+			   Minimum amount of power accepted from a sink
+			   when negotiating
+
+Example:
+
+fusb302: typec-portc@54 {
+	compatible = "fcs,fusb302";
+	reg = <0x54>;
+	interrupt-parent = <&nmi_intc>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	fcs,max-sink-microvolt = <12000000>;
+	fcs,max-sink-microamp = <3000000>;
+	fcs,max-sink-microwatt = <36000000>;
+};

drivers/staging/typec/fusb302/TODO

@@ -4,3 +4,7 @@ fusb302:
 - Find a non-hacky way to coordinate between PM and I2C access
 - Documentation? The FUSB302 datasheet provides information on the chip to help
   understand the code. But it may still be helpful to have a documentation.
+- We may want to replace the  "fcs,max-snk-microvolt", "fcs,max-snk-microamp",
+  "fcs,max-snk-microwatt" and "fcs,operating-snk-microwatt" device(tree)
+  properties with properties which are part of a generic type-c controller
+  devicetree binding.

drivers/staging/typec/fusb302/fusb302.c

@@ -90,6 +90,7 @@ struct fusb302_chip {
 	struct i2c_client *i2c_client;
 	struct tcpm_port *tcpm_port;
 	struct tcpc_dev tcpc_dev;
+	struct tcpc_config tcpc_config;
 
 	struct regulator *vbus;
 
@@ -1198,7 +1199,6 @@ static const struct tcpc_config fusb302_tcpc_config = {
 
 static void init_tcpc_dev(struct tcpc_dev *fusb302_tcpc_dev)
 {
-	fusb302_tcpc_dev->config = &fusb302_tcpc_config;
 	fusb302_tcpc_dev->init = tcpm_init;
 	fusb302_tcpc_dev->get_vbus = tcpm_get_vbus;
 	fusb302_tcpc_dev->set_cc = tcpm_set_cc;
@@ -1684,7 +1684,9 @@ static int fusb302_probe(struct i2c_client *client,
 {
 	struct fusb302_chip *chip;
 	struct i2c_adapter *adapter;
+	struct device *dev = &client->dev;
 	int ret = 0;
+	u32 v;
 
 	adapter = to_i2c_adapter(client->dev.parent);
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_I2C_BLOCK)) {
@@ -1699,8 +1701,22 @@ static int fusb302_probe(struct i2c_client *client,
 	chip->i2c_client = client;
 	i2c_set_clientdata(client, chip);
 	chip->dev = &client->dev;
+	chip->tcpc_config = fusb302_tcpc_config;
+	chip->tcpc_dev.config = &chip->tcpc_config;
 	mutex_init(&chip->lock);
 
+	if (!device_property_read_u32(dev, "fcs,max-sink-microvolt", &v))
+		chip->tcpc_config.max_snk_mv = v / 1000;
+
+	if (!device_property_read_u32(dev, "fcs,max-sink-microamp", &v))
+		chip->tcpc_config.max_snk_ma = v / 1000;
+
+	if (!device_property_read_u32(dev, "fcs,max-sink-microwatt", &v))
+		chip->tcpc_config.max_snk_mw = v / 1000;
+
+	if (!device_property_read_u32(dev, "fcs,operating-sink-microwatt", &v))
+		chip->tcpc_config.operating_snk_mw = v / 1000;
+
 	ret = fusb302_debugfs_init(chip);
 	if (ret < 0)
 		return ret;