net: dsa: introduce dsa_user_ports helper

Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/dsa/mt7530.c

@@ -688,7 +688,7 @@ mt7530_cpu_port_enable(struct mt7530_priv *priv,
 	 * the switch
 	 */
 	mt7530_write(priv, MT7530_PCR_P(port),
-		     PCR_MATRIX(priv->ds->enabled_port_mask));
+		     PCR_MATRIX(dsa_user_ports(priv->ds)));
 
 	return 0;
 }

drivers/net/dsa/mv88e6060.c

@@ -175,9 +175,8 @@ static int mv88e6060_setup_port(struct dsa_switch *ds, int p)
 	 */
 	REG_WRITE(addr, PORT_VLAN_MAP,
 		  ((p & 0xf) << PORT_VLAN_MAP_DBNUM_SHIFT) |
-		   (dsa_is_cpu_port(ds, p) ?
-			ds->enabled_port_mask :
-			BIT(dsa_to_port(ds, p)->cpu_dp->index)));
+		   (dsa_is_cpu_port(ds, p) ? dsa_user_ports(ds) :
+		    BIT(dsa_to_port(ds, p)->cpu_dp->index)));
 
 	/* Port Association Vector: when learning source addresses
 	 * of packets, add the address to the address database using

drivers/net/dsa/qca8k.c

@@ -551,8 +551,7 @@ qca8k_setup(struct dsa_switch *ds)
 		/* CPU port gets connected to all user ports of the switch */
 		if (dsa_is_cpu_port(ds, i)) {
 			qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT),
-				  QCA8K_PORT_LOOKUP_MEMBER,
-				  ds->enabled_port_mask);
+				  QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds));
 		}
 
 		/* Invividual user ports get connected to CPU port only */

include/net/dsa.h

@@ -276,6 +276,11 @@ static inline bool dsa_is_user_port(struct dsa_switch *ds, int p)
 	return !!(ds->enabled_port_mask & BIT(p));
 }
 
+static inline u32 dsa_user_ports(struct dsa_switch *ds)
+{
+	return ds->enabled_port_mask;
+}
+
 static inline const struct dsa_port *dsa_to_port(struct dsa_switch *ds, int p)
 {
 	return &ds->ports[p];

net/dsa/dsa2.c

@@ -312,7 +312,7 @@ static int dsa_ds_apply(struct dsa_switch_tree *dst, struct dsa_switch *ds)
 	 * the slave MDIO bus driver rely on these values for probing PHY
 	 * devices or not
 	 */
-	ds->phys_mii_mask = ds->enabled_port_mask;
+	ds->phys_mii_mask |= dsa_user_ports(ds);
 
 	/* Add the switch to devlink before calling setup, so that setup can
 	 * add dpipe tables

net/dsa/legacy.c

@@ -136,7 +136,7 @@ static int dsa_switch_setup_one(struct dsa_switch *ds,
 	/* Make the built-in MII bus mask match the number of ports,
 	 * switch drivers can override this later
 	 */
-	ds->phys_mii_mask = ds->enabled_port_mask;
+	ds->phys_mii_mask |= dsa_user_ports(ds);
 
 	/*
 	 * If the CPU connects to this switch, set the switch tree